ED-901
Dolby surr ound AC-3 Decoder
Instruction Manual
DOLBY SURROUND AC-3 DECODER
INPUT SELECTOR
OUTPUT CH. MODE
ON
ON
－10dB
C
S
POWER
PROGRAM STATUS
R
DELAY TIME
CINEMA Re-EQ MIDNIGHT THEATER LEF LEVEL
CENTER
SURROUND
INPUT
1
(VDP)
INPUT
2
(DVD)
L
C
LS
RS
mSEC.
AC-3
ED-901
ON
OFF
CONTENTS
Features................................................ 2
Important Safeguards........................... 3
Precautions .......................................... 4
Introduction ......................................... 5
Speaker Placement............................... 6
Control Positions and Names .............. 7
Connections ......................................... 8
Operations............................................ 9
Block Diagram................................... 13
Troubleshooting Guide ...................... 14
Specifications .................................... 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
1. Read Instructions — All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions — The safety and operating instructions
should be retained for future reference.
3. Heed Warnings — All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions — All operating and use instructions should
be followed.
5. Water and Moisture — The appliance should not be used near
water — for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement; or near a swimming pool, and the
like.
6. Carts and Stands — The appliance should be used only with a
cart or stand that is recommended by the manufacturer.
6A. An appliance and cart combination should be moved with care. Quick
stops, excessive force, and uneven surface may cause the appliance
and cart combination to overturn.
PORTABLE CART WARNING
S3125A
7. Wall or Ceiling Mounting —
The appliance should be mounted
to a wall or ceiling only as recommended by the manufacturer.
8. Ventilation — The appliance should be situated so that its
location or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed, sofa,
rug, or similar surface that may block the ventilation openings; or if
placed in a built-in installation, such as a book case or cabinet that
may impede the flow of air through the ventilation openings, there
should be free space of at least 20 cm (8 in.) and open up behind the
appliance.
9. Heat — The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10. Power Sources — The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
11. Polarization — The polarization of the plug is a safety feature. The
polarized plug will only fit the outlet one way. If the plug does not fit
fully into the outlet, try reversing it. If there is still trouble, the user
should seek the services of a qualified electrician. Under no
circumstances should the user attempt to defeat the polarization of the
plug.
12. Power-Cord Protection — Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items placed
upon or against them, convenience receptacles, and the point where
they exit from the appliance.
13. Cleaning — The appliance should be cleaned only as recom-
mended by the manufacturer.
14. Nonuse Periods — The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
15. Object and Liquid Entry — Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
16. Damage Requiring Service —
The appliance should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance;
or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
17. Servicing — The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Warranty card
The serial number is written on the rear panel of the unit.
Write the serial number and model number on your warranty
card and keep it in a safe place.
2. Recording Copyright
Recording of copyrighted material for other than personal use
is illegal without permission of the copyright holder.
3. AC fuse
The fuse is located inside the chassis and is not user service-
able. If power does not come on, contact your ONKYO
service center.
4. Care
From time to time you should wipe off the front and rear
panels and the cabinet with a soft cloth. For heavier dirt,
dampen a soft cloth in a weak solution of mild detergent and
water, wring it out, and wipe away the dirt. Following this,
dry immediately with a clean cloth. Do not use rough
material, thinners, alcohol or other chemical solvents or
cloths since these may damage the finish or remove the panel
lettering.
5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
• Some models are designed for use only with the power supply
voltage of the region where they are sold.
European model:
U.S.A. and Canadian models:
AC 230 V, 50 Hz
AC 120 V, 60 Hz
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Onkyo’s ED-901 Dolby Surround AC-3 Decoder brings your home the excitement of Dolby Surround AC-3 sound effects from your
LaserDiscs, etc. that employ the latest Dolby AC-3 technology. The ED-901 consists of an AC-3RF demodulator, an AC-3 decoder, and
a Cinema Re-EQ circuit.
An ideal AC-3 home theater system may include either an Onkyo TX-SV919THX or TX-SV828THX surround receiver. These receivers
can be connected to the ED-901 through the DB-25 connector.
What is Dolby Surround AC-3?
· Dolby Surround AC-3 is a new-generation digital audio format for multi-channel surround audio. With this digital audio format, you
can create a five full-range channel system called a “3/2” channel surround system (left, center, right, and two surround channels),
which is a developed version of the conventional “3/1” channel surround system” (left, center, right, and only one surround channel).
· Adding to its five full range channels, Dolby Surround AC-3 supports an LFE (low frequency effect) channel, which is used solely
for low frequency sounds independent of the other channels. Dolby Surround AC-3 is sometimes referred to as a “5.1” channel
format since this LFE channel is indicated as 0.1.
· This fully discrete 5.1 channel Dolby Surround AC-3 can reproduce sound of wide and dynamic range, changing your room into a
home theater.
· Currently, LaserDisc is the only medium that employs the Dolby Surround AC-3 technology. In the near future, however, Dolby
Surround AC-3 will be implemented in such media as DVD (Digital Video Disc), CATV (Cable Television), DBS (Direct Broadcast-
ing), and HDTV (High Definition Television).
Dolby Surronud AC-3
Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, “AC-3”, and the double-D symbol are trademarks
of Dolby Laboratories Licensing Corporation.
Copyright 1992 Dolby Laboratories, Inc. All rights reserved.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Placement
Speaker Placement
We recommend that you use the ED-901 in conjunction with the Onkyo TX-SV919THX or TX-SV828THX surround receiver. If you
have a complete THX speaker system that is connected to either of these receivers, the addition of new speakers or arrangement of the
current speaker configuration is unnecessary.
If you do not have a complete THX speaker system...
The highest quality Dolby Surround AC-3 sound can be reproduced when the ED-901 is connected to five full range THX speakers and
one or more subwoofers. To get the most out of the ED-901, it is strongly recommended that you set-up a complete THX speaker system.
To use ED-901 without a complete THX speaker system...
If no Center speaker or Surround speaker is connected to your system, the sound to the unused channel can be properly distributed to
other channels.
To do so, turn off the indicator corresponding to the unused channel by pressing the CENTER button or SURROUND button on the front
panel (see page 10).
Note:
You must make the similar setting on your TX-SV919THX or TX-SV828THX surround receiver. See the Receiver Instruction Manual.
<Fig. Speaker Placement>
Center
Center
Front Left
Front Left
Front Right
Front Right
Subwoofer
Subwoofer
Left Surround
Right Surround
Left Surround
Right Surround
Front Right
Right Surround
Front Left
Center
Subwoofer
Left Surround
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Positions and Names
NOTE:
If there is a protective film on the surface of the display, making it difficult to read the display, remove it.
For more information about the function of a particular button, please turn to the page listed in the brackets ([ ]) following each name.
11
10
9
8
7
1
2
3
4
5
6
DOLBY SURROUND AC-3 DECODER
INPUT SELECTOR
OUTPUT CH. MODE
ON
ON
－10dB
C
S
POWER
PROGRAM STATUS
R
DELAY TIME
CINEMA Re-EQ MIDNIGHT THEATER LEFT LEVEL
CENTER
SURROUND
INPUT
1
(VDP)
INPUT
2
(DVD)
L
C
LS
RS
mSEC.
AC-3
ED-901
ON
OFF
Front panel
1. POWER button [9]
6. DELAY TIME button and indicator [11]
7. CINEMA Re-EQ button and indicator [12]
8. MIDNIGHT THEATER button and indicator [12]
9. LFE LEVEL button and indicator [12]
10. CENTER button and indicator [10]
2. INPUT1 (VDP) Input Selector [9]
3. INPUT2 (DVD) Input Selector [9]
4. AC-3 indicator
This LED lights if you play AC-3 compatible software.
5. PROGRAM STATUS indicators
11. SURROUND button and indicator [10]
These LEDs indicate which output channels the software
uses.
Supplied accessories
Audio connection cable (1)
Video/Digital (Coaxial) connection cable
(2)
DB-25 cord (1)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
· Do not plug in the power cord until all connections have been made.
· Before connecting the ED-901 to the receiver, make sure that the POWER switches on both the ED-901 and the receiver are in the
OFF position.
· On each pair of input jacks, the lower jack (marked R: Red) corresponds to the right channel and the upper jack (marked L: White) to
the left channel.
· Be sure to read the Receiver Instruction Manual in addition to this manual.
For connection to the Onkyo TX-SV828THX surround
receiver...
For connection to the Onkyo TX-SV919THX surround
receiver...
· Connect the other end of the video cable (supplied) to the
VIDEO-1 IN terminal of the TX-SV828THX.
· Read “AC-3 decoder connection” in the “Optical pre-
amplifier connections” section of the TX-SV828THX
Manual.
· On the TX-SV828THX, select “External Decoder” in the
Surround Setup menu. See Fig. 4 in the “Operating Sur-
round” section (page 42) of the TX-SV828THX Manual.
· Connect the other end of the video cable (supplied) to the
VIDEO-4 IN terminal of the TX-SV919THX.
· On the TX-SV919THX, set the External Decoder mode to
“ON”.
See the “Setting External Decoder Parameter” section (page
55) of the TX-SV919THX Manual and set the parameters set
by "Level Calibration (TEST TONE)..."(page 33), because
External decoder parameters are able to be set independently
from THX mode parameters.
VDP
DVD
Note:
S video
VDP with AC-3RF output is
S video Audio Video
OUT
Audio
out
required for AC-3 reproduction.
Optical
OUT
Video
OUT
OUT
AC-3RF
out OUT
L
R
L
R
Coaxial
OUT
ED-901
Plug in the AC
power cord to a
wall outlet if
you have
connected all the
other cables.
OUTPUT
IT
I
2
OUTPUT
IN
INP
2
S-VIDEO
VIDEO
DOLBY SURROUND AC-3 DECODER
MODEL NO. ED-901
RATING:
INPUT 2
(D)
INPUT 1
(VDP)
AC120V 60Hz
25W
COAL
OL
ARF
ONKYO CORPORATION
MULTI-CHANNEL AUDIO OUTPUT
DB-25
2-1,NISSHIN-CHO,NEYAGAWA-SHI,OSAKA,
JAPAN
MADE IN JAPAN
COAXIAL OPTICAL
AUDIO
DB-25 cable
(included)
Audio cable
(included)
Video cable
(included)
S cable
(option)
Note:
Fasten the screws
with a screwdriver
to secure
the connections.
R
L
VideoS-Video
VIDEO-4
IN
External decorder input
S
TX-SV828THX or TX-SV919THX
VIDEO-1
IN
External
decorder
input
V
L
IN
R
VIDEO-1
VIDEO-4 IN
(TX-SV919THX)
VIDEO-1 IN
(TX-SV828THX)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Note:
• Before performing the following procedure, make sure that the
ED-901 is properly connected to the surround receiver.
• To play Dolby Pro Logic sound sources...
4
3
The ED-901 is not equipped with a Dolby Pro Logic decoder.
To play Dolby Pro Logic sound sources, connect the ED-901 to
your receiver by audio cables and set the receiver's Input
Selector to Analog Input ("VIDEO-4" for the TX-SV919THX
and "VIDEO-1" for the TX-SV828THX).
1. Turn on the power of the sur-
round receiver.
Perform the necessary settings, such as
adjusting output level of each channel,
on the surround receiver.
3
POWER
See the instruction manual of your
surround receiver for details.
2. Set the surround receiver’s Input
Selector as follows:
ON
OFF
TX-SV919THX: “VIDEO-4”
TX-SV828THX: “VIDEO-1”
Then, select the External Decoder mode
on the surround receiver.
4
(See also "For connection to the Onkyo
TX-SV919THX/TX-SV828THX
surround receiver..." on page 8.)
3. Press the POWER button on the
ED-901 to turn it on.
INPUT 1 (VDP)
INPUT 2 (DVD)
4. Press the INPUT 1 (VDP) or
INPUT 2 (DVD) input selector
button.
The LED for the selected input source
will light.
5. Play the AC-3 sound source.
The PROGRAM STATUS indicator
will appear on the display.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Output Channel Mode
Setting the Output Channel Mode
(OUTPUT CH. MODE)
·
The highest quality Dolby Surround
AC-3 sound can be reproduced when
the ED-901 is connected to five full-
range THX speakers and one or more
subwoofers. To get the most out of the
ED-901, it is strongly recommended
that you set-up a complete THX
speaker system.
·
If no Center speaker or Surround
speaker is connected to your system,
the sound to the unused channel can be
properly distributed to other channels:
If Center speaker is not connected...
Turn off the C indicator by pressing the
CENTER button.
C
turn off
turn off
If Surround speakers are not con-
nected...
Turn off the S indicator by pressing the
SURROUND button.
CENTER
Note:
Setting the Output Channel mode on the
ED-901 does not change the Speaker Mode
setting of the surround receiver (TX-
SV919THX or TX-SV828THX). Be sure to
set the surround receiver properly accord-
ing to the instructions in the Receiver
Instruction Manual.
S
SURROUND
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
DELAY TIME
Setting the Surround Delay
For Dolby Surround AC-3, as opposed to
the conventional Dolby Pro Logic technol-
ogy, it is unnecessary to set the time delay
between front speakers and surround
speakers. The only thing you should
consider is the difference between the front
speaker-listener distance and surround
speaker-listener distance.
1. Press the DELAY TIME button
repeatedly until the desired
delay time is displayed.
The factory-set default is 5 ms (millisec-
onds). Each time the DELAY TIME button
is pressed, the time increases by 1 ms. You
can set a delay time within the range of 0
to 15 ms.
DELAY TIME
mSEC.
A rule of thumb is that it takes 1 ms for
sound to travel one foot. For example, if
the front speakers and the surround
speakers are located the same distance
from the listening position, you should set
the delay time as “0”; If the front speaker-
listener distance is one foot longer, set the
delay time to “1 ms” and so on.
Note:
· If your surround receiver’s delay time
has been accurately set for Dolby Pro
Logic Surround play, make the ED-
901’s delay time 15 ms shorter than
that time.
· If you have changed the speaker
arrangement, change the speaker
output setting as appropriate both on
the ED-901 and on the surround
receiver. The settings of these two are
independent of each other.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Re-EQ is licensed from Lucasfilm, Ltd. U.S. patent numbers 5,043,970; 5,189,703; 5,222,059. Foreign patents pending. Lucasfilm and
Re-EQ are trademarks of Lucasfilm Ltd.
MIDNIGHT TEATER
LFE LEVEL
CINEMA Re-EQ
Using the Cinema Re-EQ, Mid-
night Theater and LFE Modes
Using the Cinema Re-EQ Mode
Press the CINEMA Re-EQ button. The
LED indicator (ON) immediately above
this button will light to indicate that you are
in the CINEMA Re-EQ mode.
ON
· Use the Cinema Re-EQ mode if your
system is placed in a small room.
CINEMA Re-EQ
Motion pictures are produced on the
assumption that they will be shown at a
large cinema. If they are shown in a
small room, however, high-frequency
range sound will be raised, resulting in
uncomfortable sound. In the Cinema
Re-EQ mode, however, the ED-901
compensates this and reproduces
optimal sound for the home theater
system.
Using the Midnight Theater Mode
Press the MIDNIGHT THEATER button.
The LED indicator (ON) immediately
above this button will light to indicate that
ON
you are in the Midnight Theater mode.
· Use the Midnight Theater mode if you
MIDNIGHT THEATER
must play a movie at low sound volume
at night. In the Midnight Theater mode,
the ED-901 makes the dynamic range
of the reproduced sound narrower for
easy-to-hear sound.
Setting the LFE Mode
Press the LFE LEVEL button. The LED
indicator (-10dB) immediately above this
button will light to indicate that the LFE
－10dB
(Low Frequency Effect) circuit is enabled.
· Use the LFE mode if the bass repro-
LFE LEVEL
duced is too loud. In the LFE mode,
the ED-901 decreases the reproduced
sound in the low-frequency channel by
10 dB.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Block Diagram
L
20 bit
D/A
AC - RF
R
AC - 3 RF
VDP
Demodulator
LS
OPTICAL
20 bit
D/A
AC-3 Decoder
RS
DVD
C
20 bit
D/A
COAXIAL
+10dB
LFE
SUB-WOOFER
VIDEO SELECTOR
S
VIDEO OUTPUT
VDP
S
VIDEO
S
Composite
VIDEO
DVD
VIDEO
AUDIO SELECTOR
L
AUDIO OUTPUT
VDP
L
R
L
R
DVD
R
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
• No power.
Cause:
pletely
Power cord is not plugged in or is not com-
inserted.
Remedy:
Firmly plug in the power cord.
• No Sound.
Cause:
Incorrect cord connections.
Remedy:
Cause:
Remedy:
Cause:
Remedy:
Cause:
Remedy:
Connect the cord properly.
Wrong input selector.
Select the proper input.
Wrong position of coaxial/optical selector.
Select the proper position.
Wrong input mode selection on the receiver.
Select the proper mode on the receiver.
• No Sound from Center or Surround Speakers.
Cause:
Remedy:
indicator for
speaker.
Wrong OUTPUT CH. MODE selection.
Put on the OUTPUT CH. MODE
the
• No Sound from Subwoofer.
Cause: No Subwoofer is selected on the receiver.
Remedy: Select Subwoofer on the receiver.
• Low Frequency Noise, Hum.
Cause: Incorrect audio cord connection.
Remedy: Firmly connect audio cords.
• Poor Bass Sound.
Cause:
Remedy:
LFE LEVEL setting is -10dB.
Put off the LFE LEVEL indicator.
• The Difference of Sound Level between Channels.
Cause:
receiver.
Remedy:
properly.
Incorrect volume level adjustment on the
Adjust volume level for each Channel
• Noise from/to nearby TV or Tuner.
Cause: This unit is too close to the affected equipment.
Remedy:
Move this unit or the affected equipment
from each other.
far
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Input Seneitivity:
and Impedance
INPUT-1,2 analog audio:
50kΩ
INPUT-1 AC-3RF:
INPUT-2digital (coaxial):
INPUT-1,2video:
S-video Y:
S-video C:
75Ω
75Ω
1Vp-p/75Ω
1Vp-p/75Ω
0.28Vp-p/75Ω
Output Level:
and Impedance
D-SUB25 5.1CH OUTPUT
LEFT, RIGHT, CENTER,
LEFT SURROUND, RIGHT SURROUND
(SUB WOOFER) :
Dolby AC-3 5CH out
L/C/R/LS/RS:
0.2V/470Ω
20 Hz - 20 kHz+0/-3dB
0.05%/1kHz
Frequency response:
Distortion:
SUBWOOFER:
0.05%/50Hz
Signal to noise ratio:
Power consumption:
Power supply rating:
98dB (Output=2v)(IHF-A)
25 watts
USA and Canadian models:
AC 120 V, 60 Hz
European model:
AC 230 V, 50 Hz
Dimensions (W × H × D): 455 × 90 × 320 mm
(17-15/16" × 3-9/16" × 12-5/8")
4.3 kg, (9.5 lbs.)
Weight:
Specifications and external appearance are subject to change without notice because of product improvements.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales Planning & Promotion Dept.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572, JAPAN
Tel: 0720-31-8111 Fax: 0720-33-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramsey, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa. com
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 18-20, 82110 Germering, GERMANY
Tel: 089 84 93 20 Fax: 089 84 93 226
ONKYO FRANCE
Immeuble Le Diamant, Domaine Technologique de Saclay, 4 Rue René Razel,
91892 SACLAY, FRANCE Tel: (1) 69 33 14 00 Fax: (1) 69 41 35 84
HOMEPAGE
SN29342251
Printed in Japan
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|