SKW-205
English
SKW-205
POWERED SUBWOOFER
POWERED SUBWOOFER
Instruction manual
SKW-205
SKW-205
Thank you
for your purchase of the Onkyo powered subwoofer.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new
powered subwoofer.
Please retain this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Warranty card
You can find the serial number on the rear panel of this
unit. In case of warranty claim, please report this number.
2. Recording Copyright
Recording of copyrighted material for other than
personal use is illegal without permission of the
copyright holder.
3. AC Fuse
The fuse is located inside the chassis and is not user-
servicable.
If power does not come on, contact your Onkyo
authorized service station.
4. Care
From time to time you should wipe off the front and
rear panels and the cabinet with a soft cloth. For
heavier dirt, dampen a soft cloth in a weak solution of
mild detergent and water, wring it out dry, and wipe off
the dirt. Following this, dry immediately with a clean
cloth. Do not use rough material, thinners, alcohol or
other chemical solvents or cloths since these may
damage the finish or remove the panel lettering.
5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION
CAREFULLY.
• The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit will
be used meets the required voltage (e.g., AC230V
50Hz or AC120V 60Hz) written on the rear panel.
• Models Equipped with a Voltage Selector
Worldwide models are equipped with a voltage
selector to conform to local power supplies. Be sure
to set this switch to match the voltage of the power
supply in your area before plugging in the unit.
Setting the voltage selector
SKW-205
220-230V
VOLTAGE
SELECTOR
120V
220-230V
120V
VOLTAGE
SELECTOR
Setting the voltage selector
1. Determine the proper voltage for your
area: 220-230V or 120V.
2. If the preset voltage is not proper for
your area, insert a screwdriver into the
groove in the switch. Slide the switch
all the way to the lower (120V) or to
the upper (220-230V) whichever is
proper.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
This subwoofer system is equipped with a
built-in amplifier solely for the reproduction of
the superbass range.
With the built-in left-right mixing circuit and
cut-off filter, you can just connect the unit to
your existing system powerful bass
reproduction.
Control positions and names
Front panel
Rear panel
A
B
SKW-205
LINE
INPUT
SPEAKER LEVEL
AUTO STANDBY
_
_
POWERED SUBWOOFER
+
R
L
L
+
+
SKW-205
INPUT
FROM
AMP/RECEIVER
L
(MONO)
OFF
ON
OUTPUT
R
TO SPEAKERS
SKW-205
_
_
+
R
POWER
1
SKW-205
C D
LISTENING MODE
MOVIE
2
3
4
MUSIC
OUTPUT LEVEL
MIN
MAX
FREQUENCY
50Hz
200Hz
To AC outlet
A Speaker-level input terminals
(INPUT FROM AMP/RECEIVER)
Connect these input terminals to the speaker output
terminals of your amplifier or receiver.
1
2
Power switch (POWER) and indicator
Pressing this button turns the power on (the indicator
lights). Pressing the button again turns the power off
(the indicator goes out).
B Speaker-level output terminals
(OUTPUT TO SPEAKERS)
The speaker-level signal to the front speakers is output
from these terminals.
Red:
Unit is in standby mode
Green: Unit is in operation
C Low-level input jacks (LINE INPUT)
Connect these jacks to the LINE OUT jacks of the
amplifier etc.
Mode selector switch (LISTENING MODE)
Selecting the MOVIE or MUSIC position provides the
optimal frequency characteristics for reproducing
movie soundtracks or music, respectively. Of course,
you can enjoy movie soundtracks and music in either
listening mode.
D Auto standby switch (AUTO STANDBY)
This switch is used to turn on and off the auto standby
function.
ON: This activates the auto standby function.
If a constant level signal is not received from the
amplifier (or receiver) over a period of a few minutes,
the SKW-205 automatically enters the standby state. If
a constant level signal is later received from the
amplifier (or receiver), the power is automatically
turned back on.
3
4
Output level adjusting knob (OUTPUT LEVEL)
Use this knob to adjust the output level of the
subwoofer.
Frequency adjusting knob (FREQUENCY)
Use this knob to select the high-frequency range at
which you wish to cut off the signal to the subwoofer.
You can select any frequency between 50 Hz and 200
Hz depending on the characteristics of the speaker
system being used with the SKW-205.
OFF: Deactivates the auto standby function.
Note:
• The auto standby function operates on the existence
or absence of a constant level input signal. If the
auto standby function does not operate properly, try
slightly increasing (or decreasing) the output level of
the amplifier or receiver. (Note that output levels of
some amplifiers and receivers cannot be adjusted.
For more details regarding your components, refer to
the instruction manual supplied with them.)
• If noise from peripheral components causes the
incorrect operation of the auto standby function, or if
outputting low volumes (i.e., during the nighttime)
causes the auto standby function to activate, turn off
the auto standby function.
• The auto standby function only operates while the
power switch for the SKW-205 is turned on.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
For safety, be sure to turn off the power of this unit and all other system components before connecting or disconnecting
any components.
When used in combination with an AV amplifier
When using the SKW-205 in conjunction with AV amplifiers and receivers with surround capability, be sure to connect the
SKW-205 to the subwoofer preout terminal (SUBWOOFER PREOUT) using the supplied pin cable. If connected using speaker
cable, depending on the amplifier or receiver settings, the bass signals may be cut out resulting in decreased fidelity in the
lower bass sounds.
For more details regarding proper connecting procedures, refer to the instruction manual supplied with your amplifier or
receiver.
Connection with amplifier’s special subwoofer jack
Connection with a preamplifier
Amplifier with subwoofer terminal
Preamplifier
Output terminals
L
To power amplifier
R
(Not supplied)
(Supplied)
LINE
INPUT
SPEAKER LEVEL
AUTO STANDBY
LINE
INPU
SPEAKER LEVEL
AUTO STANDBY
_
_
+
R
L
+
_
_
+
R
L
+
INPUT
FROM
INPUT
FROM
AMP/RECEIVER
AMP/RECEIVER
L
(MONO)
L
(MONO)
FF
ON
OFF
ON
OUTPUT
R
TO SPEAKERS
OUTPUT
R
TO SPEAKERS
_
_
+
R
L
+
_
_
+
R
L
+
SKW-205
SKW-205
Note:
Note:
If your receiver (amplifier) is equipped with a monaural
subwoofer jack, connect it to the SKW-205 Right or Left
low-level (LINE INPUT) jack.
With an ordinary preamplifier having two output chan-
nels, connect both the Right and Left jacks.
Connection to receiver's (amplifier's) speaker terminals
1. Using the supplied speaker cables and speaker cables
that came with your speakers, connect the SKW-205
speaker-level input (INPUT FROM AMP/ RECEIVER)
terminals and the amplifier’s speaker terminals.
2. Connect the Right and Left speakers to the SKW-205
speaker-level output (OUTPUT TO SPEAKERS)
terminals.
Receiver
(Amplifier)
Speaker (R)
Speaker (L)
Speaker terminals
_
_
+
R
L
+
Note:
SKW-205
SPEAKER LEVEL
• When connecting the speaker cables, be sure not to
mistake the (+) and (-) and the L (left) and R (left). If
the speaker cables are connecting incorrectly, there
will be a loss of fidelity in the bass sound ranges.
• The speakers connected to the SKW-205 speaker-
level output (OUTPUT TO SPEAKERS) terminals must
have an impedance equal to or greater than the rating
indicated on the amplifier connected to the speaker-
level input (INPUT FROM AMP/ RECEIVER) terminals.
Otherwise, amplifier damage may occur.
_
_
+
R
L
L
+
+
INPUT
FROM
AMP/RECEIVER
OUTPUT
TO SPEAKERS
_
_
+
R
Connecting the speaker cables
1. Press the lever of the speaker output terminal, fully
insert the twisted core wires into the terminal hole, and
then release the lever.
2. Pull the speaker cable lightly to ensure that it is
connected firmly.
Note:
• When you have connected the speaker cables, make
sure that the core wires are not in contact with other
terminals or metallic parts of the unit.
• Do not use BTL (Balanced Transformer-Less) type
amplifiers. Using a BTL amplifier may cause damage
to both the amplifier and the subwoofer. Ordinary
amplifiers are not BTL amplifiers. For details, see the
amplifier’s instruction manual.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Subwoofer effects
Adding a subwoofer to your speaker system expands the bandwidth of reproduced bass-range sound. If the subwoofer’s
reproduction bandwidth or sound output level is improperly adjusted, however, the overall performance may be decreased
as shown in the graphs below.
When subwoofer’s reproduction bandwidth is
correct
When subwoofer’s reproduction bandwidth is
far from speaker’s bandwidth
Overall characteristics
Speaker characteristics
Curve is sunken
Subwoofer characteristics
When subwoofer’s output level is incorrect
When subwoofer’s reproduction bandwidth is
close to speaker’s bandwidth
Output level is too high
Curve is raised
Output level is too low
Adjustments
Crossover frequency and output level
The placement of the SKW-205 can greatly affect the
sound that is produced. Under normal circumstances,
placement in the corner of the room provides the best
results.
• Adjust the SKW-205 output level and the crossover fre-
quency properly for your listening room and connected
speakers.
• When the unit is connected to an amplifier via the speaker-
level input (INPUT FROM AMP/RECEIVER) terminals,
setting the OUTPUT LEVEL knob near the center position
will provide a well-balanced sound level with most speakers.
• Note that you may possibly set the subwoofer at high output
levels because superbass-range sound is not so audible as
sound in other ranges. To obtain well-balanced frequency
characteristics, set the output level to a slightly lower level
than seems optimal. (This will also prevent the input of too
strong signals.)
Note:
Be careful not to allow the input of excessive power. Input
levels that greatly exceed normal situations can damage
the SKW-205. Also note that switching operations at the
amplifier can also cause excessive noises that may cause
damage. When using switches at the amplifier, first lower
the volume to prevent accidental damage.
Precaution on use
• Four slip-proof spacers are provided with the SKW-205. If the
SKW-205 is to be placed on flooring or other similar surfaces,
attach these spacers to the bottom surface at the corners. This
will not only prevent scratching, but also provide a stable
footing. However, note that depending on the surface, the
spacers may leave markings.
• This unit is designed to be used in the upright vertical position
only. Do not use it in the horizontal or tilted position.
• If the unit is used near a turntable or CD player, howling or
skipping of sound may occur. To prevent this, move the unit
away from the turntable or CD player or otherwise lower the
unit’s output level.
Placement
• The enclosure is made of wood and therefore sensitive to
extreme temperatures and humidity. Avoid placing the unit in
locations subjected to direct sunlight or in humid places such as
near an air conditioner, bathroom or kitchen, as well as in
locations subjected to soot or steam such as near a kitchen
table and humidifier. Otherwise, damage may occur.
• Keep water or other liquids away from the unit. If water is spilled
into the unit, not only the unit but also the connected receiver
(amplifier) may be damaged.
• Place the unit on a level and rigid surface free from vibration.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Howling when a microphone is used
• This unit can handle the specified input power when it is used
for ordinary music reproduction. If the following abnormal
signals are fed to the unit, however, an overcurrent may flow in
the internal circuits, causing burning or breakage of the wires
even if the input power is below the specified rating.
1. Special test signals produced by audio checking CD, etc.
2. Sound produced when connecting or disconnecting audio
connection cables
4. Abnormal sound produced when bass-range signals are
excessively boosted by using the receiver's (amplifier's)
tone controls, a graphic equalizer, etc., or when a source
whose bass range is abnormally boosted is being played
This state called “rattling” occurs when the signal is beyond
the driver’s reproduction capacity. Although it is not a sign
of damage, decrease the speaker output level to prevent
damage to the driver.
(Always turn off the amplifier's power before connecting or
disconnecting cables.)
Troubleshooting guide
Symptom
Cause
Remedy
The unit does not turn on.
• The power plug is not fully inserted.
• Insert the power plug fully into the power
outlet.
No sound output
• The OUTPUT LEVEL knob is set to
the MIN level.
• Pin-connector cable(s) are discon-
nected at the LINE INPUT jacks.
• Speaker cables are not properly
connected to the INPUT FROM
RECEIVER terminals.
• Set the OUTPUT LEVEL knob properly.
• Connect cable(s) to the LINE INPUT jacks.
• Connect the speaker cables properly.
• The input signal is so small that the
unit entered the standby state.
• Set the AUTO STANDBY switch to OFF.
• Connect the speaker cables properly.
Small sound output
Hum noise
• Speaker cables are connected to the
INPUT FROM RECEIVER terminals
with reversed phase.
• Playing source does not include
superbass sound.
• Play sources with superbass sound.
• Fully insert the pin-connector.
• Pin-connector is not inserted com-
pletely.
• External leakage flux (induction noise • Separate from the noise source and connect.
by TV etc.) occurs.
Specifications
Type
Bass-reflex with built-in power
Speaker
20-cm woofer
amplifier
Power supply
AC 220-230 V and 120 V
switchable, 50/60 Hz
Use
For superbass-range
reproduction
Power consumption
42 W
Frequency response
30-200 Hz
(at maximum crossover frequency)
Dimensions (W × H × D)
235 × 455 × 347 (mm)
9-1/4" × 17-15/16" × 13-11/16"
Crossover frequency
Maximum output power
Input impedance
50-200 Hz (variable)
60 W
Weight
Others
11.2 kg 24.7 lbs
AUTO STANDBY ON/OFF
(with CANCELLING Switch)
MOVIE/MUSIC mode selection
Magnetic shielding
4.7 kΩ
(for speaker-level input terminals)
12 kΩ
(for low-level input jacks)
Sensitivity
Speaker-Level
Line
✽
Specifications and appearance may subject to change
for improvement without prior notice.
0.8 V
30 mV
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
HOMEPAGE
D0004-1
SN 29342918
Download from Www.Somanuals.com. All Manuals Search And Download.
|