CD Receiver
CR-555
CR-555DAB
Instruction Manual
Thank you for purchasing an Onkyo CD receiver.
Please read this manual thoroughly before
making any connections and plugging it in.
Following the instructions in this manual will
enable you to obtain optimum performance and
listening enjoyment from your new CD receiver.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal
without the permission of the copyright holder.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical solvents,
because they may damage the finish or remove the
panel lettering.
• When you’ve finished using this unit, remove all
discs and turn off the power.
9. Installing this Unit
4. Power
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do
not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
10. To Obtain a Clear Picture—This unit is a
hightech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
your Onkyo dealer for details.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
extended period, remove the power cord from the
AC outlet.
5. Preventing Hearing Loss
Caution
11. Moisture Condensation
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from
an air conditioned room to a hot and humid
place.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
– The unit is used in a humid place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
If condensation does occur, unplug the power cord
and leave the unit for two to three hours in the room
temperature.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for the
ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
The label on the right is
applied on the rear panel.
For European Models
1. This unit is a CLASS 1 LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified
personnel.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Amplifier
• WRAT (Wide Range Amplifier Technology)
• Symmetrical Designed Power Amplifier Circuitry
• 2 Digital Inputs (1 Optical/1 Coaxial)
• 3 Audio Inputs and 1 Output
VLSC™ is a trademark of Onkyo Corporation.
• Optimum Gain Volume Circuitry
• 3 Stage Inverted Darlington Amplifier Design
• Subwoofer Pre Out
Windows Media, and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
CD Player
• Plays CDs, MP3/WMA CDs, CD-Rs and CD-RWs
• 25 Track Programming
• 2 Repeat Mode (Track/Full)
• 3 Play Modes (Normal/Random/Memory)
• VLSC (Vector Linear Shaping Circuitry)
• 192 kHz/24-bit D/A Converters
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and
iPod touch are trademarks of Apple Inc., registered in the
U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect specifically
to iPod or iPhone, respectively, and has been certified by the
developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance
with safety and regulatory standards.
iPod / iPhone
®
®
• iPod /iPhone Digital Direct Connection via USB
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
USB Interface
• MP3/WMA compatible
• 3 Repeat Modes (Track/Full/1 Folder)
• 3 Play Modes (Normal/Random/1 Folder)
Tuner & Other
• 40 AM/FM Presets (CR-555)
• 40 FM/40 DAB Presets (CR-555DAB)
• Sleep Timer
• Sleep&Charge Function
• Phase-Matching Bass Boost System
• Auto Standby Function
• Headphone Jack
• Aluminium Front Panel
• RI-Dock Compatible Remote Control (iPod/iPhone
Control Capable)
• Aluminium Volume Knob
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Make sure you have the following accessories:
Remote controller (RC-849S) and two batteries
(AAA/R03)
(Note for China: The battery for the remote controller is not
supplied for this unit.)
Indoor FM antenna (CR-555)
Indoor FM/DAB antenna (CR-555DAB)
AM loop antenna (CR-555)
Power cord
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
Before Using the CD receiver
Installing the Batteries
Using the Remote Controller
When you operate the remote controller, point it at the
CD receiver’s remote control sensor, as shown below.
CD receiver
Batteries (AAA/R03)
Note:
Remote control
sensor
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
Note:
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or corrosion.
• The remote controller may not work reliably if the CD
receiver is subjected to bright light, such as direct
sunlight or inverter-type fluorescent lights. Keep this
in mind when installing.
• If another remote controller of the same type is used in
the same room, or the CD receiver is installed close to
equipment that uses infrared rays, the remote
controller may not work reliably.
• Don’t put anything, such as a book, on the remote
controller because the buttons may be pressed
inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the CD
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and the CD receiver’s remote
control sensor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting Started
Listening to the Radio
Presetting FM Stations Automatically
Connections
Advanced Operations
Connecting an Onkyo RI Dock
Miscellaneous
Basic Operations
Playing CDs
iPod / iPhone Playback
Using USB interface
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the CD receiver
Front Panel
a
b
c
d
e
f
g
hi jk l
m n
The page numbers in parentheses show where you can find the main explanation for each item.
h TONE button
Used to adjust the tone.
b VOLUME control
This control is used to adjust the volume of the
CD receiver to “Min”, “1” through “41”, “Max”.
d USB port
l MENU/ENTER jog dial
Used as the Previous/Next button and the
MENU/ENTER button.
Connect an iPod/iPhone or USB flash drive to this
port.
It is also used for various settings.
g INPUT button
Used to select the input source.
Display
a
b
c
d
ef g h
i j
n
p
k
l
m
o
The page numbers in parentheses show where you can find the main explanation for each item.
AUTO indicator
c DIGITAL, ANALOG indicators
1FOLDER indicator
TUNED indicator
MEMORY indicator
AM indicator (CR-555)
RANDOM indicator
FM STEREO indicator
DAB indicator (CR-555DAB)
RDS indicator (European models)
̃ indicator
̃1 indicator
8
Download from Www.Somanuals.com. All Manuals Search And Download.
f Message area
Rear Panel
(CR-555)
(CR-555DAB)
a
b c d
e
f
j
g
h
i
a SPEAKERS
f AC INLET
b u REMOTE CONTROL
g SUBWOOFER PRE OUT
This u (Remote Interactive) jack can be
This jack is for connecting a powered subwoofer.
connected to an u jack on Onkyo RI Dock.
h LINE OUT
c AUX IN
This analog audio output is for connecting a
recorder such as cassette deck.
This stereo minijack (ø3.5mm) is for connecting an
audio source.
i DIGITAL IN COAXIAL and OPTICAL
d LINE IN
j DAB/FM ANTENNA (CR-555DAB)
These analog audio inputs are for connecting Onkyo
RI Dock and cassette deck, etc.
See pages 13–15 for connection information.
e FM ANTENNA
AM ANTENNA (CR-555)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
The page numbers in parentheses show where you can
find the main explanation for each item.
a
b
c
n
o
b DISPLAY button
Used to change the information shown on the
display.
d
f Previous/Next [7]/[6] and
e
p
q
f
g
h Arrow [!]/["]/[#]/[$] and ENTER buttons
i MENU button
Used with various functions and settings for
selecting.
h
i
j TONE/BAL button
Used to adjust the tone.
r
s
m Number buttons
Used to select tracks and radio presets.
j
t
u
k
l
m
v
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Notes
Note:
Precautions for Playback
• A disc recorded with a recorder or personal computer
may not play in some cases. (Cause: Disc’s
characteristics, damaged or dirty disc, dirt on player’s
lens, dew condensation, etc.)
• A disc recorded on a personal computer may not play
because of the application settings or environment.
Record the disc with the proper format. (Contact the
application maker for details.)
Compact discs (CDs) with the following logo on the
label surface can be used. Do not use discs designed for
purposes other than audio, such as CD-ROMs for PC
use. Abnormal noise could damage the speakers or
amplifier.
• A disc with insufficient storage capacity may not
playback properly.
*
This CD receiver supports CD-R and CD-RW discs. Note
Playback of MP3 Discs
that some discs may not playback because of the disc
characteristics, scratches, contamination or the recording
state. A disc recorded with an audio CD record will not
playback unless it is finalized.
• Only MP3 files with the extension “.MP3” or “.mp3”
are supported.
• This CD receiver supports files recorded in MPEG 1
Audio Layer 3 (32-320 kbps), with the sampling rate
of 32/44.1/48 kHz.
• Variable bitrates (VBR) between 32 kbps and
320 kbps are supported. The time information during
VBR playback may not display correctly.
Never use discs which have a special shape (such as
hearts or octagons). These types of discs could jam and
damage the CD receiver.
Playback of WMA Discs
®
• WMA stands for “Windows Media Audio”, an audio
compression technology developed by Microsoft
Corporation USA.
• Only WMA files with the extension “.WMA” or
“.wma” are supported.
• Encode the WMA file with an application approved by
Microsoft Corporation USA. The file may not
playback correct if encoded with an unapproved
application.
CD Playback with Copy-control Function
Some audio CDs with copy-control function do not
comply with official CD standards. These are special
discs and cannot be played with this CD receiver.
Playback of MP3 and WMA Discs
MP3 and WMA files recorded on a CD-R/CD-RW can
be played with this CD receiver.
• Variable bitrates (VBR) between 32 kbps and
192 kbps (32/44.1/48 kHz) are supported.
• Copyright-protected WMA files cannot be played
back.
• Use discs which have been recorded following the
ISO9660 Level 2 file system. (The supported directory
depth is eight levels, the same as ISO9660 Level 1)
Discs recorded with the hierarchical file system (HFS)
cannot be played.
• WMA Pro, Lossless and Voice are not supported.
• Up to 99 folders (including the root folder), and up to
499 folders (including root) and files can be
recognized and played.
• Always close the disc tray.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Discs
Caring for Discs
Hold discs by the edge, or by the center hole and edge.
Avoid touching the playback surface (surface with
nothing printed on it).
If the disc is dirty, the CD receiver will have a hard time
reading signals, and the audio quality may drop. If the
disc is dirty, gently wipe off fingerprints and dust with a
soft cloth. Lightly wipe from the center outwards.
To remove stubborn dust or dirt,
Label surface
(printed surface)
wipe the disc with a soft cloth
dampened with water, and then
dry it with a dry cloth. Do not
use cleaning spray for analog
records or antistatic agents, etc.
Playback surface
Never use volatile chemicals
Do not attach paper or stickers, or write on the playback
or label surface of the disc. Take care not to scratch or
damage the disc.
such as benzine or paint thinner
as they can impregnate the disc
surface.
Precautions for Rental Discs
Do not use discs with residue from cellophane tape,
rental discs with labels which are peeling off, or discs
with decorative labels. This type of disc could get stuck
in the CD receiver, or could damage the CD receiver.
Precautions for Inkjet Printable Discs
Do not leave a CD-R/CD-RW having a label printed with
an inkjet printer in the CD receiver for a long time. The
disc could get stuck in the CD receiver, or could damage
the CD receiver.
Remove the disc from the CD receiver when not being
played, and store it in a case. A freshly printed disc will
stick easily, and should not be played immediately.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas
This section explains how to connect the supplied FM antenna, AM loop antenna (CR-555), and DAB antenna (CR-
555DAB). The CD receiver won’t pick up any radio signals without an antenna connected, so you must connect the
antenna to use the tuner.
(CR-555)
Insert the plug fully into the jack.
Push.
Insert wire.
Release.
Caution:
Assembling the AM loop antenna
• Be careful not to injure yourself when
using thumbtacks.
Thumbtacks, etc.
AM loop antenna (supplied)
Indoor FM antenna (supplied)
(CR-555DAB)
Caution:
• Be careful not to injure
yourself when using
thumbtacks.
Insert the plug fully into
the jack.
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM
antenna instead.
• (CR-555) If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a
commercially available outdoor AM antenna.
• Once the CD receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM
antenna to achieve the best possible reception.
• Keep the antenna as far away as possible from the CD receiver, TV, speaker cables, and power cords.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Speakers
■ Screw-type speaker terminals
Strip 12 to 15 mm of insulation from the ends of the
speaker cables, and twist the bare wires tightly, as
shown.
Connecting Your Speakers
• Connect the right speaker to the CD receiver’s right
(R) SPEAKERS terminals. Connect the left speaker to
the left (L) SPEAKERS terminals.
12 to 15 mm
• Connect the positive (+) terminal on each speaker to
the corresponding positive (+) terminal on the CD
receiver. Connect the negative (–) terminal on each
speaker to the corresponding negative (–) terminal on
the CD receiver. Use the red wires to connect the
positive (+) terminals.
• Connect only speakers with an impedance of between
4 and 16 ohms. Connecting a speaker with a lower
impedance may damage the speaker.
Left speaker
Right speaker
• Be careful not to short the positive and negative wires.
Doing so may damage the CD receiver.
• Do not connect both speaker cables to the same L or R
terminals (Fig. 1). Do not connect more than two
speaker terminals to each speaker (Fig. 2).
Speaker
cable
Red wires
Fig. 1
Fig. 2
LINE INPUT
LINE INPUT
Powered subwoofer
Connecting Other Components
About Connections
• Before making any connections, read the manuals
supplied with your other components.
• Don’t connect the power cord until you’ve completed
and double-checked all connections.
Note:
• Do not put anything on top of the CD receiver, as it
may interfere with proper ventilation.
Caution:
• To prevent shutter damage, hold the optical plug
straight when inserting and removing.
• Push plugs in all the way to make
good connections (loose
Right!
connections can cause noise or
malfunctions).
• To prevent interference, keep
audio cables away from power
cords and speaker cables.
Wrong!
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an Onkyo RI Dock (Remote Interactive Dock)
The following diagram shows how to connect an optional Onkyo RI Dock (Remote Interactive Dock).
Connect either of them.
R
L
ON/STANDBY
STANDBY
ANALOG
AUDIO OUT
iPod
PC
U
NSYNC
SYNC/
RI Dock
Digital Media Transport
What can you do with u?
• Connecting an Onkyo RI Dock to the CD receiver with an u cable allows you to control the RI Dock with the CD
receiver’s remote controller. In addition, when playback is started on the RI Dock, the CD receiver will automatically
select it as the input source.
• To use u, you must connect the Onkyo RI Dock to the CD receiver with an u cable (If you connect the Onkyo RI
Dock to LINE IN, you also need to connect it with an analog audio cable.). On the RI Dock, set the RI MODE switch
to “HDD” or “HDD/DOCK”. See the RI Dock’s instruction manual for details.
Connecting the Power Cord
Note:
• Before connecting the power cord, connect all of your speakers and components.
• Turning on the CD receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the CD receiver into a different branch circuit.
• Never disconnect the power cord from the CD receiver while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the CD receiver.
• Do not use a power cord other than the one supplied with the CD receiver. The supplied power cord is designed
exclusively for use with the CD receiver and should not be used with any other equipment.
Connect the supplied power cord to the CD receiver’s AC INLET.
1
To AC wall outlet
Plug the power cord into an AC wall outlet.
2
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
This manual describes the procedure for using the
remote controller, unless otherwise specified.
Adjusting the Tone
Press the [TONE] button repeatedly.
Setting will change in the following orders:
1
Turning On the CD receiver
Bass, Treble, Balance, PM.Bass, Direct
To turn on the CD receiver, press the On/Standby [8]
Use the Arrow [#]/[$] buttons to adjust the
button on the remote controller.
2
tone.
Press the On/Standby [8] button again to set the CD
receiver to Standby.
Bass, Treble
–3 to 0 to +3 in 1 steps. (The default value is 0.)
You can also use the [8ON/STANDBY] button on the
CD receiver.
Balance
Tip:
L7 to 0 to R7 in 1 steps. (The default value is 0.)
PM.Bass (Phase Matching Bass)
From the warm low notes produced by a cello to the
deep frequencies of electronic music, a good
compact audio system should be able to deliver
plenty of bass resonance.
While traditional enhancement systems effectively
boost low-frequency sound, they are often prone to
the effects of phase shifting, which can overwhelm
mid-range frequencies and muddy the sound. Our
Phase-Matching Bass Boost technology effectively
preserves mid-range clarity-allowing vocals and
strings to shine-while maintaining a smooth,
powerful bass response at all volume levels.
When the Phase Matching Bass function is on, the
S.Bass indicator appears on the display.
On
Adjusting the Volume
To adjust the volume, use the VOLUME [q/w] button.
You can also use the [VOLUME] control on the CD
receiver.
Selecting the Input Source
To select the input source, press the remote controller’s
[INPUT SELECTOR] button. On the CD receiver, press
the [INPUT] button repeatedly. The input sources are
selected in the following order.
(CD receiver)
→
CD
→
←
LINE1
FM
→
USB
LINE2
→
AUX IN
OPTICAL
Off (default)
AM
←
←
COAXIAL
←
Note:
DAB
• If the PM.Bass function is set to “On”, “Direct”
function cannot be selected. You need to set the
PM.Bass function to “Off” to enable “Direct”
function.
(Remote controller)
[LINE]:
LINE1
→
LINE2
→
AUX IN
Direct
[DIGITAL]:
[TUNER]:
OPTICAL ↔ COAXIAL
When the Direct function is on, the tone controls are
bypassed, so you can enjoy a pure sound.
The DIRECT indicator appears on the display.
On
AM
FM
↔
DAB
Off (default)
Note:
• If the Direct function is set to “On”, the “Bass”,
“Treble” and “PM.Bass” functions cannot be
selected. You need to set the Direct function to
“Off” to enable those settings.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Display Brightness
Muting the Sound
You can adjust the brightness of the CD receiver’s
display.
To mute the output of the CD receiver, press the remote
controller’s [MUTING] button. The MUTING indicator
appears on the display.
To unmute the CD receiver, press the [MUTING] button
again.
Press the [DIMMER] button repeatedly to
cycle through the following patterns:
1
• Normal brightness.
• Dim brightness.
• Dimmer brightness.
Tip:
While the CD receiver is muted:
• Turning the [VOLUME] control on the CD receiver or
pressing the VOLUME [q/w] buttons on the remote
controller will unmute the CD receiver.
• If you turn the CD receiver off, the next time you turn
it on, the CD receiver will be unmuted.
Using Headphones
Turn down the volume, then connect your stereo
headphones to the Phones minijack.
The speakers output no sound while the headphones are
connected.
Using the Sleep Timer
With the sleep timer, you can set the CD receiver so that
it automatically turns off after a specified period.
Press the [SLEEP] button repeatedly to select
the required sleep time.
With the [SLEEP] button, you can set the sleep time from
90 to 10 minutes in 10 minute increments.
When the sleep timer has been set, the SLEEP indicator
appears on the display. The sleep time appears on the
display for about 5 seconds, then the previous display
reappears.
Checking the Remaining Sleep Time
To check the remaining sleep time, press the [SLEEP]
button.
Note that if you press the [SLEEP] button while the sleep
time is being displayed, you’ll shorten the sleep time by
10 minutes.
Canceling the Sleep Timer
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs
Displaying CD Information
Press the Open/Close [0] button to open the
1
disc tray.
During playback, press the remote controller’s
[DISPLAY] button repeatedly to display the following
CD information.
Place the CD on the tray with the label-side
facing up.
2
Place 8 cm CDs in the center of the tray.
• Elapsed time
• REMAIN
Lights up while the remaining track time is being
displayed.
• TOTAL REMAIN
Lights up while the remaining disc time is being
displayed.
To start playback, press the Play [1]
3
button.
The disc tray closes and playback starts.
The Play 1 indicator appears.
To stop playback:
Press the Stop [2] button.
The total time is more than 99 minutes and 59 seconds,
“– –:– –” is displayed.
To pause playback:
Press the Pause [3] button. The Pause 3 indicator
appears. To resume playback, press the Pause [3] or
Play [1] button again.
Selecting Files (MP3/WMA)
There are two modes for selecting files (MP3/WMA
files): Navigation mode and All Folder mode.
In Navigation mode, you can select files (MP3/WMA
files) by navigating through the folder hierarchy, moving
in and out of folders and subfolders.
In All Folder mode, all folders appear at the same level,
making it easy to select folders regardless of the
hierarchy.
To Fast-Forward or Fast-Reverse
During playback or while playback is paused, press
and hold the Fast Forward [4] button to fast
forward, or the Reverse [5] button to fast reverse.
To remove the CD:
Press the Open/Close [0] button to open the disc
tray.
• Audio CD Display
In this manual, MP3/WMA files are referred to as
files. Likewise, folders (directories) are referred to as
folders.
“DISC TOTAL” lights up.
Note:
Total number
of tracks
Total playing time
• If you don’t select a specific MP3/WMA file or folder
for playback, all of the MP3/WMA files on the disc
will be played in numerical order starting with file #1.
• MP3/WMA CD Display
Disc name or Format
Selecting Files in Navigation Mode
This mode can only be used while playback is stopped.
While playback is stopped, press the Stop
1
Total number
of folders
Total number
of files
[2] button.
The CD receiver enters Navigation mode and
“[Root]” appears on the display.
Selecting Tracks
Press the Play [1] button.
2
The name of the first folder one level down from root
appears on the display.
To return to the beginning of the track currently
playing, press the Previous [7] button.
If the disc contains no folders, the first file name
appears.
Press the Previous [7] button repeatedly to select
earlier tracks.
• While playback is stopped, pressing the Previous
[7] button will select the previous track.
Use the Previous and Next [7]/[6]
3
buttons to select other folders and files at
the same level.
Press the Next [6] button to select subsequent
tracks.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Cancelling Navigation or All Folder Mode
To cancel Navigation mode or All Folder mode while
selecting MP3/WMA files, return to upper hierarchy and
press the Stop [2] button.
To access files or subfolders inside another
4
folder, select the folder, and then press Play
[1] button.
Use the Previous and Next [7]/[6] buttons to
select the files and subfolders within that folder.
To move up a level, press the Pause [3] button.
■ To Select Folders and Files by Number
Use the number buttons as shown in the examples
below to enter folder numbers.
To start playback, press the [ENTER] or Play
5
(Audio CD)
[1] button.
For example, to specify file #8, press [8].
To specify file #34, press [>10], [3], and [4].
To specify file #134, press [>10], [1], [3], and [4].
Tip:
• You can also use the Stop [2] button and
[MENU/ENTER] jog dial on the CD receiver.
Tip:
Note:
• If a folder contains more than 99 files, single- and
double-digit file numbers must be preceded by
zeros.
be set from “STOP KEY” (see page 21).
Selecting Files in All Folder Mode
(MP3/WMA CD)
Press [>10] once to select the files, twice to select
the folders and enter the numbers.
This mode can only be used while playback is stopped.
While playback is stopped, press the Pause
1
[3] button.
Displaying MP3/WMA Information
You can display various information about the
MP3/WMA file currently playing, including ID3 tags
such as title, artist name, and album name.
The CD receiver enters All Folder mode, and “1”
appears on the display.
Use the Previous and Next [7]/[6]
2
buttons to select the other folders.
To play the first file in the selected folder, go to Step
4.
During playback, press the [DISPLAY] button
repeatedly to display the following MP3/WMA
information.
To access the files inside the folder, press
3
the Play [1] button.
• Elapsed time
To select the files in the folder, repeat the step 2.
To select another folder, press the Pause [3] button
again, and then use the Previous and Next
[7]/[6] buttons to select it.
If the elapsed time is more than 99 minutes and 59
seconds, “– –:– –” is displayed.
• File name
• Folder name
To start playback, press the [ENTER] or Play
4
• Title name (if ID3 tag present)
• Artist name (if ID3 tag present)
• Album name (if ID3 tag present)
• Sampling rate and bit rate
[1] button.
Tip:
• You can also use the Stop [2] button (press and hold)
Note:
and [MENU/ENTER] jog dial on the CD receiver.
• If a file or folder name contains any characters that
cannot be displayed, an underscore will be displayed
in place of those characters. Alternatively, you can set
the CD receiver so that names containing such
characters are displayed as “File_n” or “Folder_n”,
“n” being the file or folder number (see page 21).
Note:
set from “STOP KEY” (see page 21).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Playback
Random Playback
With memory playback, you can create a playlist of up
to 25 tracks.
With random playback, all of the tracks on the disc are
played in random order.
This mode can only be used while playback is stopped.
This mode can only be used while playback is stopped.
Press the [RANDOM] button. The RANDOM
indicator appears.
Press the [MEMORY] button. The MEMORY
1
indicator appears.
Cancelling Random Playback
• To cancel random playback, press the [RANDOM]
button.
Use the Previous and Next [7]/[6]
2
buttons to select the first track you want to
add to the playlist, and then press the Play
[1] button.
• Random playback is cancelled when you press the
Open/Close [0] button to open the disc tray, or turn
off the CD receiver.
Repeat this step to add additional tracks to the
playlist.
You can also use the number buttons on the remote
controller to select tracks.
Repeat Playback
To select MP3/WMA files for memory
playback:
With repeat playback, you can play an entire CD
repeatedly, play one track repeatedly, or combine it with
memory playback to play the playlist repeatedly, or
random playback to play all of the tracks on the disc in
random order repeatedly.
In All Folder mode, use steps 1-3 on page 19.
• You can add up to 25 tracks to the playlist. If you
try to add more, the message “Memory Full”
appears.
Press the [REPEAT] button repeatedly until the
̃ or ̃1 indicator appears.
To start memory playback, press the Play
3
[1] button.
Repeat-1 playback can’t be combined with memory
playback, random playback.
Selecting Other Tracks During Memory
Playback
Cancelling Repeat Playback
• To cancel repeat playback, press the [REPEAT] button
repeatedly until both the ̃ and ̃1 indicators
disappear.
To select other playlist tracks during memory playback,
use the remote controller’s Previous and Next
[7]/[6] buttons.
• Repeat playback is cancelled when you press the
Open/Close [0] button to open the disc tray, or turn
off the CD receiver.
Checking What’s on the Playlist
To check what tracks are on the playlist, with playback
stopped, use the Fast Reverse and Fast Forward
[5]/[4] buttons to scroll through the playlist.
Removing Tracks from the Playlist
• While memory playback is stopped, press the
[CLEAR] button. Each press removes the last track
from the playlist.
Cancelling Memory Playback
• To cancel Memory playback, press the [MEMORY]
button.
• The playlist will be deleted when you cancel memory
playback, select random playback, press the
Open/Close [0] button to open the disc tray, or turn
off the CD receiver.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ID3 VER.2
Setting MP3/WMA Preferences
This preference determines whether or not version
2.2/2.3/2.4 tags are read and displayed. When set to “Not
Read”, version 2.2/2.3/2.4 ID3 tags will not be
displayed.
With the MP3/WMA preferences, you can change the
way MP3/WMA file information is displayed and the
way MP3/WMA CDs are played.
This mode can only be used while playback is stopped.
Read (default)
Not Read
Press the [MENU] button, and then use the
1
Arrow [!]/["] buttons to select “MP3
CD EXTRA
Setting”.
This preference applies to CD Extra discs and
determines whether music in the audio session or
MP3/WMA files in the data session are played.
Press [ENTER].
2
Use the Arrow [!]/["] buttons to select the
Audio (default)
MP3
3
preference you want to change.
The preferences are explained in the next column.
JOLIET
Press [ENTER].
This preference applies to MP3/WMA CDs in Joliet
format and determines whether the CD receiver reads the
SVD data or treats the disc as an ISO 9660 disc.
Normally, this preference doesn’t need to be changed.
SVD (Supplementary Volume Descriptor) supports long
file and folder names and characters other than letters
and numbers.
4
5
Use the Arrow [#]/[$] buttons to select the
preference’s options.
Press [ENTER].
6
When the preference has been set, “Complete”
appears on the display.
Use SVD (default)
ISO9660
Tip:
• To cancel the procedure at any point, press the
[MENU] button.
HIDE NUMBER
This preference determines whether or not the numbers
at the beginning of file and folder names are hidden.
When you create an MP3/WMA CD on a personal
computer, you cannot normally determine the playback
order of the files. However, if you number the
MP3/WMA files in order, starting with 01, 02, 03, and so
on, they will play in that order. If you don’t want these
numbers to appear on the display, choose “Enable”.
• Press the [RETURN] button to return to the previous
menu.
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
Preferences
BAD NAME
This preference determines whether or not file and folder
names that contain undisplayable characters are replaced
with “File_n” or “Folder_n”, “n” being the file or folder
number. When set to “Not”, displayable characters are
displayed and underscore characters are used in place of
any undisplayable characters.
Disable:
(default)
Enable:
The file and folder name, including
numbers, will be displayed as is.
The file and folder name will be
displayed but numbers will be
hidden.
For ID3 tags, underscore characters are used in place of
undisplayable characters regardless of this preference.
STOP KEY
This preference determines how the Stop [2] button on
the CD receiver works.
Replace
Not (default)
When the “Navigation” option is selected, pressing the
Stop [2] button once selects Navigation mode.
When the “All Folder” option is selected, pressing the
Stop [2] button once selects All Folder mode.
• When the “Disable” option is selected, CD receiver
does not enter Navigation or All Folder mode by
pressing the Stop [2] button.
ID3 VER.1
This preference determines whether or not version
1.0/1.1 tags are read and displayed. When set to “Not
Read”, version 1.0/1.1 ID3 tags will not be displayed.
Read (default)
Not Read
Navigation (default)
All Folder
Disable
21
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod / iPhone Playback
Playing an iPod/iPhone via USB
iPod/iPhone Playback via Onkyo
Dock
• Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
• Set the CD receiver’s Input Display to “DOCK”.
Use the [INPUT SELECTOR] button to select
“DOCK”.
1
To start playback, press [ENTER] or the Play
[1] button.
2
To pause playback:
Press the [3] button. To resume playback, press the
[3] button again.
To Fast-Forward or Fast-Reverse
During playback, press and hold the Fast Forward
[4] button to fast forward, or the Reverse [5]
button to fast reverse.
Compatible iPod/iPhone models
Made for:
iPod touch (1st, 2nd, 3rd and 4th generation),
iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th
generation), iPhone 4S, iPhone 4, iPhone 3GS,
iPhone 3G, iPhone
Selecting Tracks
Note:
the previous or next track.
• With the following iPod/iPhone, the charging mode
does not work when it is connected in standby mode.
iPod touch (1st, 2nd and 3rd generation), iPod nano
(2nd generation), iPhone 3GS, iPhone 3G, iPhone
Tip:
on a USB Flash Drive” (see page 23). With some
iPod/iPhone models and generations, certain buttons
may not work as expected.
Press the [USB] button.
1
• The [RETURN] button is used as a menu button.
• The Arrow [!]/["] buttons are used to scroll up and
down the list and file.
Connect the USB cable that comes with the
iPod/iPhone to the USB port on the front of
the CD receiver.
2
Note:
• To adjust the volume, use the VOLUME [q/w] button.
You can also use the [VOLUME] control on the CD
receiver.
The message “iPod” appears.
Tip:
• When connecting your iPod/iPhone with a USB
cable, we recommend you use an official USB
cable from Apple Inc.
• If you use your iPod/iPhone with any other
accessories, iPod/iPhone playback detection may not
work.
Use the Arrow [!]/["] buttons to select a
3
folder, and then press [ENTER] to open it.
Displaying Music File Information
Use Arrow [!]/["] buttons to select a
4
You can display various information about the music
files currently playing.
music file, and press [ENTER] or the Play
[1] button to start playback.
During playback, press the [DISPLAY] button
repeatedly to display the following music file
information.
Tip:
• You can also use the [INPUT] button and
[MENU/ENTER] jog dial on the front panel.
• The [RETURN] button is used as a menu button.
• For the basic button operation and play mode, refer to
page 23). With some iPod/iPhone models and
generations, certain buttons may not work as
expected.
• Title name
• Artist name
• Album name
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using USB interface
The CD receiver can play back MP3 and WMA files that
have been stored on USB flash drives and MP3 players.
Use the [USB] buttons to select “USB”.
The USB indicator lights.
• When no USB flash drive is connected, “No USB”
will be displayed.
• When there is no MP3, WMA or AAC file in the
USB flash drive, “No USB” will be displayed.
1
2
Supported Audio File Formats
For USB flash drive playback, the CD receiver supports
the following music file formats.
To start playback, press the Play [1]
■ About FAT
button.
• Supports FAT16 and 32.
• Supports up to 499 files per folder.
• Supports up to 499 folders.
Playback will begin with the top file in the folder
organization.
To stop playback:
■ MP3 decoder
Press the Stop [2] button.
• Supports MPEG Audio 1, 2 and 2.5.
• Supports Layer 1, 2 and 3.
• Supports sample rates 8 k, 16 k, 32 k, 11.025 k,
22.05 k, 44.1 k, 12 k, 24 k and 48 kHz.
• Supports bit rates 8 to 320 kbps and VBR (Variable
Bit Rate).
To pause playback:
Press the Pause [3] button. The Pause 3 indicator
appears. To resume playback, press the Pause [3]
button again.
■ WMA decoder
• Supports WMA Ver. 9 standard.
• Does not support DRM.
Display during Stop
USB indicator
• Supports sample rates 8 k, 16 k, 32 k, 11.025 k,
22.05 k, 44.1 k, 12 k, 24 k and 48 kHz.
• Supports bit rates 5 to 384 kbps and VBR (Variable
Bit Rate).
Total number of folders
Total number of files
■ AAC decoder
• Supports MPEG4 AAC-LC encoded by iTunes.
• Does not support DRM.
Note:
• In general, playback of USB flash drive music files is
a repeating playback. When all music files have been
played, playback will repeat from the top music file in
the folder organization. The type of repeat playback
• Supports sample rates 8 k, 16 k, 32 k, 11.025 k,
22.05 k, 44.1 k, 12 k, 24 k and 48 kHz.
• Supports bit rates 8 to 320 kbps and VBR (Variable
Bit Rate).
Selecting Music files
Playing Music Files on a USB Flash
Drive
To return to the beginning of the music file currently
playing, press the Previous [7] button.
This section explains how to play music files on a USB
flash drive.
Connect a USB flash drive as shown below.
Press the Previous [7] button repeatedly to select
previous file.
• While playback is stopped, pressing the Previous
[7] button will select the previous file.
Press the Next [6] button to select next file.
Selecting Music files in other folders
1. Press the [<10] button to display the current folder
name.
The folder name will flash.
2. To select the previous folder, press the Previous
[7] button.
USB flash drive
To select the next folder, press the Next [6]
button.
3. To start playback, press the Play [1] button.
Playback will start from the first file in the
selected folder.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
Press the [REPEAT] button repeatedly to select
the type of repeat playback.
• Repeat playback (default):
• Do not connect the CD receiver’s USB port to a USB
port on your computer. Music on your computer
cannot be played through the CD receiver in this way.
• Operation with all USB flash drives including the
ability to power them is not guaranteed.
• Do not connect your USB flash drive via a USB hub.
The USB flash drive must be connected directly to the
CD receiver’s USB port.
̃ indicator appears
• Repeat-1 playback:
Repeats a single selected file.
̃1 indicator appears
• 1-Folder playback:
• If the USB flash drive contains a lot of data, the CD
receiver make take a while to read it.
Repeat playback of all files in a selected folder. ̃
and 1FOLDER indicators appear.
Resume Playback
Note:
After playback has been stopped, when the Play [1]
button is pressed to begin playback again, it will resume
playback from the beginning of the file in which it
stopped.
Repeat-1 or 1-Folder playback can’t be combined with
random playback.
Displaying Music File Information
Cancelling Resume Playback
You can display various information about the MP3,
WMA or AAC files currently playing, including ID3
tags such as title, artist name, and album name.
While playback is stopped, press the Stop [2] button.
“ResumeClear” will appear on the display.
Resume will be cleared even if the following operations
are performed:
• another music file is selected;
• the power cord is unplugged;
During playback, press the [DISPLAY] button
repeatedly to display the following music file
information.
• the USB flash drive is unplugged during playback.
Elapsed time
The length of time that the current MP3, WMA or
AAC file has been playing (default display). If the
elapsed time is more than 99 minutes and 59
seconds, “– –:– –” is displayed.
• File name
Random Playback
With random playback, all of the music files on the USB
flash drive are played in random order.
This mode can only be used while playback is stopped.
• Folder name
Press the [RANDOM] button.
The RANDOM indicator appears.
1
• Title name (if ID3 tag present)
• Artist name (if ID3 tag present)
• Album name (if ID3 tag present)
To start random playback, press the Play
2
[1] button.
Charging Mode
Cancelling Random Playback
If you set the “SleepCharge” function to “On”, you can
supply power to the USB device (mobile device)
connected to the CD receiver. If you connect the USB
device (mobile device) while the CD receiver is in the
standby mode, charging will start and the message
“Charging” appears. The same applies to the case when
the CD receiver enters the standby mode by pressing the
On/Standby [8] button.
• To cancel random playback, press the [RANDOM]
button. The RANDOM indicator disappears.
• Random playback is cancelled when the USB flash
drive is removed or the CD receiver is set to Standby.
Select the type of Repeat Playback
When playing back USB flash drive music files, all files
on the USB flash drive will be played according to repeat
playback (̃ indicator is already lit up). The type of
Repeat playback can be selected.
Tip:
• If you press any of the On/Standby [8] button,
Open/Close [0] button and Play [1] button,
charging will stop.
Note:
• For details of the charging mode, refer to
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
Tuning into Radio Stations
Presetting FM Stations Automatically
(Auto Preset)
With the Auto Preset function, you can automatically
preset all of the FM radio stations available in your area
in one go. Presets make it easy to select your favorite
stations and eliminate the need to tune the radio
manually each time you want to change stations. The
Auto Preset function does not preset AM radio stations
Band
Frequency
(Actual display depends on country)
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Auto Preset Caution!
Any existing presets will be deleted when the
Auto Preset function is run.
Press the [TUNER] button repeatedly to
select “AM” or “FM”.
1
Press the [ENTER] button repeatedly. The
AUTO indicator appears.
2
Press the [TUNER] button repeatedly to
select “FM”.
1
•
Auto Tuning Mode
Press the [MENU] button, and then use the
2
The AUTO indicator appears and stereo radio
reception is possible.
Arrow [!]/["] buttons to select
“TunerSetting”.
•
Manual Tuning Mode
Press [ENTER].
The AUTO indicator is not displayed and radio
reception will be in mono.
3
4
Use the Arrow [!]/["] buttons to select
Use the TUN [e]/[r] buttons to tune into a
station.
“AutoPreset”.
3
Press [ENTER].
5
In Auto tuning mode, once a station is found,
tuning stops automatically.
A message requesting confirmation appears.
To cancel the Auto Preset function at this point, press
the [MENU] button.
Radio frequency can be changed in 0.05 MHz steps
for FM and 9 kHz or 10 kHz steps for AM.
In Manual Tuning mode, the frequency stops
changing when you release the button. Press the
button repeatedly to change the frequency one step at
a time.
To start the Auto Preset function, press
[ENTER].
Up to 40 stations can be preset and presets are stored
in frequency order.
6
Tip:
Tip:
• Press and hold the Play/Pause [1/3] button on
• You can also use the [INPUT] button and
[MENU/ENTER] jog dial on the CD receiver.
the CD receiver to switch between modes.
Tuning into stations by frequency
Changing radio wave intensity
(CR-555DAB)
You can tune into AM and FM stations directly by
entering the appropriate frequency.
If the weak radio station is frequently received during
Auto Preset/Scan, set the “SearchLevel” setting to
“Strong” to receive the strong radio station only. The
default setting is “Normal”.
Press the [TUNER] button repeatedly to
select “AM” or “FM”, followed by the
[D.TUN] button.
1
Within 8 seconds, use the number buttons
2
Press the [MENU] button, and then use the
1
to enter the frequency of the radio station.
For example, to tune to 87.5 (FM), press [8], [7], [5],
[0].
If you have entered the wrong number, you can retry
after 8 seconds.
Arrow [!]/["] buttons to select
“TunerSetting”.
Press [ENTER].
2
3
Use the Arrow [!]/["] buttons to select
“SearchLevel”.
Press [ENTER].
4
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the Arrow [#]/[$] buttons to select
Selecting Preset Stations
5
“Normal” or “Strong”.
You must store some presets before you can select them
Press [ENTER].
“Complete” appears on the display.
6
Use the [TUNER] button to select “AM” or
“FM”.
1
Tip:
The preset you selected the last time you listened to
the radio will still be selected.
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
Use the PRESET [e]/[r] buttons to select a
2
Presetting AM/FM Stations Manually
preset.
You can also use the number buttons to
select presets.
With the Preset Write function, you can manually preset
individual AM and FM radio stations. You can store a
combination of up to 40 of your favorite AM/FM radio
stations as presets.
Tip:
• You can also use the [INPUT] button and
[MENU/ENTER] jog dial on the CD receiver.
Tune into the station that you want to store
as a preset.
1
Press the [MENU] button, and then use the
Receiving RDS
2
Arrow [!]/["] buttons to select
Press the [DISPLAY] button repeatedly to display the
following RDS information.
• Frequency and preset number
• Preset name*1
• Program Service Name
• Radio Text (if available)
“TunerSetting”.
Press [ENTER].
3
4
Use the Arrow [!]/["] buttons to select
“PresetWrite”.
Press [ENTER].
5
RDS is only available on European models and only in
areas where RDS broadcasts are available.
The preset number flashes.
To cancel the Preset Write function at this point,
press the [MENU] button.
What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
within the European Broadcasting Union (EBU) and
many European FM radio stations use it these days.
The CD receiver supports and displays the Program
Service Name (PS) and Radio Text (RT) types of RDS
data.
Use the Arrow [#]/[$] buttons to select a
6
preset.
To store the station, press [ENTER].
7
If no station has yet been stored to the selected
preset, “Complete” appears and the station is stored.
If a station has already been stored in the selected
preset, the message “OverWrite?” appears.
To overwrite the previously stored station, press the
[ENTER] button.
The RDS indicator appears on the display when the CD
receiver is tuned to an FM station that supports RDS.
Note:
To not overwrite the previously stored station, press
the [MENU] button.
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
• The message “Waiting…” may appear while the RT
data is being received.
Tip:
• You can also use the [MENU/ENTER] jog dial on
the CD receiver.
*1
If the selected preset has no name, it will be skipped and the next
Program Service Name will be displayed.
For European models
If the current FM station supports RDS and PS (Program
Service Name), the station’s name will be displayed
instead of the frequency.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying Presets
Erasing Presets
With the Preset Copy function, you can organize your
presets in the order you want. When you copy a preset,
its name is also copied.
Select the preset you want to erase (see
1
Press the [MENU] button, and then use the
Arrow [!]/["] buttons to select
“TunerSetting”.
2
Select the preset you want to copy (see
page 26).
1
Press the [MENU] button, and then use the
Press [ENTER].
2
3
4
Arrow [!]/["] buttons to select
Use the Arrow [!]/["] buttons to select
“TunerSetting”.
“PresetErase”.
Press [ENTER].
3
Press [ENTER].
5
Use the Arrow [!]/["] buttons to select
A message requesting confirmation appears.
To cancel the Preset Erase function at this point,
press the [MENU] button.
4
“PresetCopy”.
Press [ENTER].
The number of the preset to be copied flashes.
5
To erase the preset, press [ENTER].
The preset is erased and “Complete” appears on the
display.
6
Use the Arrow [#]/[$] buttons to select the
6
destination preset.
The number of the destination preset flashes.
Tip:
To copy the preset, press [ENTER].
7
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
If no station has yet been stored in the destination
preset, the station is copied and “Complete” appears.
If a station has already been stored in the destination
preset, the message “OverWrite?” appears.
To overwrite the previously stored station, press
[ENTER].
To not overwrite the previously stored station, press
the [MENU] button.
Tip:
• If you favorite station is stored in preset #5 and you
want to make it preset #1, copy preset #5 to preset #1.
To keep the station that’s already stored in preset #1,
you may want to copy it to an unused preset first.
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Naming Presets
Space:
Enters a space character.
Shift*1:
Toggles between lower and upper case
You can name presets for easy identification. The preset
name may contain of up to eight characters.
Select the preset you want to name (see
characters.
(Left)/ (Right):
1
Press the [MENU] button, and then use the
Moves the cursor left or right in the Name input
2
Arrow [!]/["] buttons to select
area.
“TunerSetting”.
BS (Back Space)*2:
Moves the cursor backward and deletes one
character.
OK:
Press [ENTER].
3
4
Use the Arrow [!]/["] buttons to select
Confirms your entry.
“Name Edit”.
Press [ENTER].
Tip:
5
*1
The available characters appear.
This can also be performed by using the [>10]
button.
Use the Arrow [!]/["]/[#]/[$] buttons to
6
*2
Press the [CLEAR] button to clear all the characters
you have input.
select a character, and then press [ENTER].
Repeat this step to enter up to 8 characters.
When you’ve finished editing the name and
7
Changing AM Frequency Step
want to store it, be sure to use the Arrow
[!]/["]/[#]/[$] buttons to select “OK” and
then press [ENTER]. If you fail to do this, the
name won’t be saved.
Press the [MENU] button, and then use the
1
Arrow [!]/["] buttons to select
“TunerSetting”.
Press [ENTER].
• The following table shows available characters.
2
3
Use the Arrow [!]/["] buttons to select
“AMFreq.Step”.
Press [ENTER].
4
5
Use the Arrow [#]/[$] buttons to select
“AMStep 9kHz” or “AMStep10kHz”.
Press [ENTER].
6
“Complete” appears on the display.
Tip:
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Preferences
Listening to DAB Digital Radio
(CR-555DAB)
Use the following functions and settings to set up DAB
digital radio.
Press the [TUNER] button repeatedly to select
“DAB”.
Press the [MENU] button, and then use the
1
Arrow [!]/["] buttons to select
“TunerSetting”.
Selecting DAB for the Very First Time
The very first time you select DAB, the Auto Scan
function automatically scans the DAB Band III for the
multiplexes (i.e., stations) available in your area. Once
the scanning process is complete, the first station that
was detected is selected.
Press [ENTER].
2
Use the Arrow [!]/["] buttons to select the
3
preference you want to change.
Press [ENTER].
4
Use the Arrow [#]/[$] buttons to select the
Using the Auto Scan Function Manually
If a new DAB station is introduced, or you move to a new
area, you can run the Auto Scan function again.
5
preference’s options.
Press [ENTER].
6
Press the [MENU] button, and then use the
1
Arrow [!]/["] buttons to select
Tip:
“TunerSetting”.
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
Press [ENTER].
2
DAB Scan
Use the Arrow [!]/["] buttons to select
3
This setting determines which DAB bands are scanned
by the Auto Scan function.
“DAB Scan”.
Press [ENTER].
4
U.K:
Band III (11B-12D)
World Wide: Band III (5A-13F)
(default)
Use the Arrow [#] / [$] buttons to select
5
“U.K” or “World Wide”, and then press
[ENTER] to start the Auto Scan function.
DAB DRC
With the DRC (Dynamic Range Control) setting, you
can reduce the dynamic range of DAB digital radio so
that you can still hear quiet parts even when listening at
low volume levels-ideal for listening to the radio late at
night when you don’t want to disturb anyone.
The number of stations found and the scanning progress
are shown on the display.
Displaying DAB Radio Information
Press the [DISPLAY] button repeatedly to display more
information about the selected DAB station.
Off:
(default)
Low:
High:
Small reduction in dynamic range.
Large reduction in dynamic range.
1. DLS (Dynamic Label Segment)
When tuned to a station that’s broadcasting DLS
text data, the text will scroll across the display.
DAB Mode
2. Program Type
With this setting, you can sort the available stations
alphabetically, by active stations, or multiplex.
3. Bit Rate and Audio Mode
4. Signal Quality
Alphabet:
(default)
Active ST.:
Sort stations alphabetically.
Sort by active stations.
Receivable stations appear at the
top of the list. Stations that cannot
be received properly appear at the
bottom of the list.
0-59: Poor reception
60-79: Good reception
80-100: Excellent reception
5. Multiplex Name
6. Multiplex Number and Frequency
Multiplex:
Sort stations by multiplex.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Setup
Sel Change
Setting Common Preferences
When you connect an Onkyo u-capable component,
it’s important that you select the input source name that
matches the type of component for u to work properly.
Before operating this setting, you need to select the input
source that you want to set.
The common setting for each input selector is explained
below. Go through the following steps for setup.
Press the [MENU] button, and then use the
1
Arrow [!]/["] buttons to select the
LINE1, LINE2, OPTICAL, COAXIAL
preference you want to change.
Press [ENTER].
2
DOCK
Note:
Use the Arrow [#]/[$] buttons to select the
3
• “DOCK” can be selected for the “LINE1”, “LINE2”,
“OPTICAL”, “COAXIAL” input selector, but not at
the same time.
preference’s options.
Press [ENTER].
4
Tip:
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
Preferences
ASb (Auto Standby)
When “Auto Standby” is set to “On”, the CD receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio signal input.
The ASb indicator lights up when the Auto Standby
function is enabled.
On
Off
Default setting: On (European models), Off (Other
models)
SleepCharge
You can specify how the power is fed to your USB
device (mobile device) when the CD receiver is in
standby mode.
On:
(default)
If you connect USB device (mobile
device), charging will start.
“Charging” appears on the display.
Your USB device (mobile device)
is not charged.
Off:
Note:
• When the “SleepCharge” setting is set to “On”, the
power consumption slightly increases in standby
mode.
• If the iPod/iPhone completely runs out of battery,
charging might not work. In that case you need to turn
the power on again.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the CD receiver, look for a solution in this section.
If you can’t resolve the issue yourself, try resetting the CD receiver before contacting your Onkyo dealer.
Note that resetting the CD receiver will delete your radio presets and custom settings.
To reset the CD receiver to its factory defaults, turn it on and, while holding down the Stop [2] button, press
the [8ON/STANDBY] button.
2
1
HOLD
“Clear” will appear on the display and the CD receiver will enter Standby mode.
Power
Can’t turn on the CD receiver.
• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
The CD receiver turns off unexpectedly.
• The CD receiver will automatically enter standby mode when Auto Standby has been set and launches.
Audio
There’s no sound.
The sound quality is not good.
• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices
away from the CD receiver.
• If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone that’s being
used to make a call, the CD receiver may output noise.
• The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during playback or
when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
Headphone output is intermittent or there’s no sound.
• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for cleaning
information. Also, make sure that the headphones cable is not broken or damaged.
Audio performance
• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time
to warm up.
• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CD Playback
Playback jumps.
Can’t add tracks to the playlist for memory playback.
• Make sure there’s a disc in the CD receiver. Also, you can only add valid track numbers. For example, if the CD
contains 11 tracks, you cannot add track #12.
The disc will not play.
• Make sure the disc has been loaded correctly, with the label-side facing up.
It takes a long time for playback to start.
• It may take the CD receiver a while to read CDs that contain many tracks or files.
Can’t Play MP3/WMA/AAC discs.
• The disc has not been finalized. Finalize the disc.
• MP3/WMA/AAC files without a “.MP3/.WMA/.AAC” or “.mp3/.wma/.aac” filename extension are not recognized.
Tuner
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all
stations, when tuned to a stereo FM station.
• Change the position of the antenna.
• Move the CD receiver away from a nearby TV or computer.
• Cars or airplanes can cause noisy interference.
• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
• Move power cords and speaker cables as far away as possible from the tuner’s antenna.
• When listening to an AM station, noise may be heard when you operate the remote controller.
• If none of the above improves the reception, install an outdoor antenna.
If a power outage occurs or the power cable is disconnected.
Can’t adjust the frequency of the radio.
• Use the Fast Reverse and Fast Forward [5]/[4] buttons to change the frequency of the radio (see page 25).
RDS doesn’t work.
• The FM station you are tuned to doesn’t support RDS.
• Install an outdoor FM antenna.
• Change the position or direction of your outdoor FM antenna.
• Move the FM antenna as far away as possible from fluorescent lights.
Remote Controller
The remote controller doesn’t work properly.
• Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)
• The remote controller is too far away from the CD receiver, or there’s an obstacle between them (see page 6).
• The CD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
• The CD receiver is located behind the glass doors of a audio rack or cabinet.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
USB flash drive Playback
Can’t access the music files on a USB flash drive.
• Make sure that the USB indicator light is on. If the light is not on, make sure that it is connected correctly and that
the USB flash drive is one that is supported (see page 23).
• The CD receiver supports USB flash drives that support the USB Mass Storage Class. However, playback may not be
possible with some USB flash drives even if they conform to the USB Mass Storage Class.
• This CD receiver cannot recognize .WAV or .wav files.
• Check that the memory format is FAT16 or FAT32.
• USB flash drives with an internal USB hub are not supported.
Can’t Play MP3/WMA/AAC Files.
• MP3/WMA/AAC files without a “.MP3/.WMA/.AAC” or “.mp3/.wma/.aac” filename extension are not recognized.
iPod/iPhone
The RI functions don’t work properly.
• Make sure the u cable is connected correctly (see page 15). If you connect the Onkyo RI Dock to LINE IN, you
also need to connect it with an analog audio cable.
• Try resetting your iPod/iPhone.
iPod/iPhone connected via USB doesn’t work properly.
• Make sure that the iPod/iPhone is connected correctly.
• Try resetting your iPod/iPhone.
Charging Mode
The charging mode does not work.
• Make sure the “SleepCharge” function is set to “On”.
• Check if the iPod/iPhone completely runs out of battery. If it completely runs out of battery, charging will start after
the CD receiver is turned on again.
• The CD receiver supports USB flash drives that support the USB Mass Storage Class. However, some of the USB
devices that meet the USB Mass Storage Class may not be supplied power.
Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure that the material will be recorded correctly.
The CD receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this
should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Amplifier Section
General
Power Supply
Power Consumption (CR-555) 72 W
AC 220 - 230 V, 50/60 Hz
Rated Output Power
All channels:
(European)
2 ch × 22 W at 4 ohms, 1 kHz, 2 ch driven
of 0.4% (IEC)
(CR-555DAB) 77 W
No-sound Power Consumption
Damping Factor
THD+N (Total Harmonic Distortion+Noise)
0.4% (1 kHz, 1 W)
22 (Front, 1 kHz, 8 Ω)
(CR-555) 30 (USB 1ALoad) W
(CR-555DAB) 35 (USB 1ALoad:DAB)
W
Stand-by Power Consumption
Input Sensitivity and Impedance (Unbalance)
150 mV/47 kΩ (LINE)
Rated RCA Output Level and Impedance
0.15 V/330 Ω (LINE OUT)
Frequency Response 10 Hz - 100 kHz/ 3 dB (LINE1)
Tone Control Characteristics
(CR-555) 0.26 W
(CR-555DAB) 0.27 W
Dimensions (W × H × D)
215 mm × 119 mm × 331 mm
4.8 kg
Weight
6 dB, 80 Hz (BASS)
8 dB, 10 kHz (TREBLE)
+8 dB, 30 Hz (PM.Bass)
■ Audio Inputs
Digital
Optical: 1
Coaxial: 1
Signal to Noise Ratio 100 dB (LINE, IHF-A)
Speaker Impedance
4 Ω - 16 Ω
Analog
LINE1, LINE2, AUX
■ Audio Outputs
Tuner Section
Analog
Subwoofer Pre Output
LINE OUT
FM Tuning Frequency Range
(European)
1
87.5 MHz - 108.0 MHz, RDS
(Others) 87.5 MHz - 108.0 MHz
AM Tuning Frequency Range (CR-555)
Speaker Outputs
Phones
Main (L, R)
1 (3.5 ø)
522 kHz - 1611 kHz
40
■ Others
Preset Channel
CD
RI
USB
1
1
Signal Readout
Optical non-contact
Specifications and features are subject to change
without notice.
Frequency Response 10 Hz - 20 kHz
Audio Dynamic Range 96 dB
THD (Total Harmonic Distortion)
0.025%
Wow and Flutter
Below threshold of measurability
Audio Output/Impedance (Analog)
2.0 V (rms)/330 Ω
34
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
Y1207-2
SN 29401160A
(C) Copyright 2012 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 1 6 0 A *
Download from Www.Somanuals.com. All Manuals Search And Download.
|