Onkyo Laser Pointer ABX N300 User Manual

Getting Started............................En-2

Wireless Music System

Connections.............................. En-13

ABX-N300

Basic Operation....................... En-15

Playing Your iPod/iPhone... En-16

Listening via the Network... En-18

Clock and Timer ...................... En-23

Network Setup.......................... En-26

Instruction Manual

Thank you for purchasing an Onkyo Wireless Music System.

Please read this manual thoroughly before making any

connections and plugging it in.

Following the instructions in this manual will enable you to obtain

optimum performance and listening enjoyment from your new

Wireless Music System.

Requirements for Internet Radio

and Media Servers ................. En-32

Please retain this manual for future reference.

Miscellaneous .......................... En-33

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal with-

out the permission of the copyright holder.

For U.S. models

FCC Statement

Federal Communication Commission Interference

Statement

2. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

3. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING

SECTION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the AC adapter.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

The AC adapter is used to disconnect this unit from

the AC power source. Make sure that the adapter is

readily operable (easily accessible) at all times.

If you do not intend to use the unit for an extended

period, remove the AC adapter from the AC outlet.

4. Batteries and Heat Exposure

Warning

FCC Caution:

Batteries (battery pack or batteries installed) shall not be

exposed to excessive heat as sunshine, fire or the like.

FCC WARNING

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment. This device complies

with Part 15 of FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause

interference, and (2) this device must accept any

interference, including interference that may cause

undesired operation of this device.

For product available in the USA/Canada market, only

channel 1~11 can be operated. Selection of other

channels is not possible. This device and its antenna(s)

must not be colocated or operation in conjunction with

any other antenna or transmitter.

5. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands

are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Onkyo

dealer.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you origi-

nally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on

the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so

be sure to use it occasionally.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment and

meets the FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65. This equipment

should be installed and operated keeping the radiator at

least 20 cm or more away from person’s body (excluding

extremities: hands, wrists, feet and ankles).

En-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions—Continued

For Canadian Models

For European Models

IC Statement

Hereby, ONKYO SOUND & VISION CORPORATION,

declares that this ABX-N300 is in compliance with the

essential requirements and other relevant provisions of

Directive 1999/5/EC.

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause

interference, and (2) this device must accept any

interference, including interference that may cause

undesired operation of the device.

С настоящето, ONKYO SOUND & VISION

CORPORATION, декларира, че ABX-N300 е в

съответствие със съществените изисквания и

другитеприложими разпоредби на Директива

1999/5/EC.

ONKYO SOUND & VISION CORPORATION tímto

prohlašuje, že ABX-N300 splňuje základní požadavky a

všechna příslušná ustanoveni Směrnice 1999/5/ES.

Undertegnede ONKYO SOUND & VISION

CORPORATION erklærer herved, at følgende udstyr

ABX-N300 overholder de væsentlige krav og øvrige

relevante krav i direktiv 1999/5/EF.

For product available in the USA/Canada market, only

channel 1~11 can be operated. Selection of other

channels is not possible. This device and its antenna(s)

must not be colocated or operation in conjunction with

any other antenna or transmitter.

IMPORTANT NOTE:

Hiermit erklärt ONKYO SOUND & VISION

CORPORATION, dass sich das Gerät ABX-N300 in

Übereinstimmung mit den grundlegenden

IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure

limits set forth for an uncontrolled environment and

meets RSS-102 of the IC radio frequency (RF) Exposure

rules. This equipment should be installed and operated

keeping the radiator at least 20cm or more away from

person’s body (excluding extremities: hands, wrists, feet

and ankles).

Anforderungen und den übrigen einschlägigen

Bestimmungen der Richtlinie 1999/5/EG befindet.

Käesolevaga kinnitab ONKYO SOUND &

VISIONCORPORATION seadme ABX-N300 vastavust

direktiivi 1999/5/EÜ põhinõuetele ja nimetatud

direktiivist tulenevatele teistele asjakohastele sätetele.

NOTE:

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ ONKYO

SOUND & VISION CORPORATION ΔΗΛΩΝΕΙ ΟΤΙ

ABX-N300 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ

ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ

Modèle pour les Canadien

IC Statement

Le présent appareil est conforme aux CNR d’Industrie

Canada applicables aux appareils radio exempts de

licence.

L’exploitation est autorisée aux deux conditions

suivantes :

(1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

Por la presente, ONKYO SOUND & VISION

CORPORATION, declara que este ABX-N300 cumple

con los requisitos esenciales y otras exigencias relevantes

de la Directiva 1999/5/EC.

Par la présente, ONKYO SOUND & VISION

CORPORATION déclare que l’appareil ABX-N300 est

conforme aux exigences essentielles et aux autres

dispositions pertinentes de la directive 1999/5/CE.

Con la presente ONKYO SOUND & VISION

CORPORATION dichiara che questo ABX-N300 è

conforme ai requisiti essenziali ed alle altre disposizioni

pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo ONKYO SOUND & VISION CORPORATION

deklarē, ka ABX-N300 atbilst Direktīvas 1999/5/EK

būtiskajām prasībām un citiem ar to saistītajiem

noteikumiem.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

Cet équipement est conforme aux limites d’exposition

aux rayonnements énoncées pour un environnement non

contrôlé et respecte les règles d’exposition aux

fréquences radioélectriques (RF) CNR-102 de l’IC. Cet

équipement doit être installé et utilisé en gardant une

distance de 20 cm ou plus entre le dispositif rayonnant et

le corps (à l’exception des extrémités : mains, poignets,

pieds et chevilles).

Šiuo ONKYO SOUND & VISION CORPORATION

deklaruoja, kad šis ABX-N300 atitinka esminius

reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

REMARQUE:

A ONKYO SOUND & VISION CORPORATION

ezzennel kijelenti, hogy a ABX-N300 típusú beren-dezés

teljesíti az alapvető követelményeket és más 1999/5/EK

irányelvben meghatározott vonatkozó rendelkezéseket.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B

EST CONFORME À LA NORME NMB-003 DU

CANADA.

En-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions—Continued

Hierbij verklaart ONKYO SOUND & VISION

CORPORATION dat het toestel l ABX-N300 in

overeenstemming is met de essentiële eisen en de andere

relevante bepalin-gen van richtlijn 1999/5/EG.

Niniejszym ONKYO SOUND & VISION

CORPORATION deklaruje że ABX-N300 jest zgodny z

zasadniczymi wymaganiami i innymi właściwymi

postanowieniami Dyrektywy 1999/5/EC.

Eu, ONKYO SOUND & VISION CORPORATION,

declaro que o ABX-N300 cumpre os requisitos

essenciais e outras provisões relevantes da Directiva

1999/5/EC.

Prin prezenta, ONKYO SOUND & VISION

CORPORATION, declară că aparatul ABX-N300 este în

conformitate cu cerinţele esenţiale şi cu alte prevederi

pertinente ale Directivei 1999/5/CE.

ONKYO SOUND & VISION CORPORATION týmto

vyhlasuje, že ABX-N300 a spĺňa základné požiadavky a

všetky príslušné ustanovenia Smernice 1999/5/ES.

ONKYO SOUND & VISION CORPORATION izjavlja,

da je ta ABX-N300 v skladu z bistvenimi zahtevami in

drugimi relevantnimi določili direktive 1999/5/ES.

ONKYO SOUND & VISION CORPORATION

vakuuttaa täten että ABX-N300 tyyppinen laite on

direktiivin 1999/5/EY oleellisten vaatimusten ja sitä

koskevien direktiivin muiden ehtojen mukainen.

Härmed förklarar ONKYO SOUND & VISION

CORPORATION att denna ABX-N300 följer de

väsentliga kraven och andra relevanta stadgar i Direktiv

1999/5/EC.

Hér með lýsir ONKYO SOUND & VISION

CORPORATION því yfir að varan ABX-N300 er í

samræmi við grunnkröfur og aðrar kröfur sem gerðar

eru í tilskipun 1999/5/EC.

ONKYO SOUND & VISION CORPORATION

erklærer herved at

denne ABX-N300 er i overensstemmelse med vesentlige

krav og andre relevante bestemmelser i direktiv 1999/5/

EC.

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding technical standards such as EN60950-1,

EN55022, EN55024 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

En-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Important Safety Instructions .......................... 2

Precautions........................................................ 3

Features ............................................................. 7

Supplied Accessories....................................... 7

Using the Remote Controller ........................... 8

Replacing the Battery ....................................... 8

Setting the Clock (remote controller only)....23

Setting the Time and Day of the Week ........23

Displaying the Clock ....................................23

Using the Timers (remote controller only)....24

About the Timers..........................................24

Setting a Timer.............................................24

Switching the Timer On (active) /

About Your iPod/iPhone................................... 9

iPod/iPhone Models that can be Connected... 9

Caution .......................................................... 9

Off (disabled).............................................25

Using the Snooze Function..........................25

Using the Sleep Timer .................................25

Getting to Know the ABX-N300...................... 10

Top/Front Panel........................................... 10

Rear Panel................................................... 11

Remote Controller (RC-806S) ..................... 12

Network Setup .................................................26

Network Essentials ......................................26

Connecting via Wireless LAN ......................27

Connecting via Wired LAN...........................28

About Standby Mode ...................................30

Checking Network Information.....................30

Viewing the “WEB Setup Menu” Window.....31

Connections .................................................... 13

Basic Operation............................................... 14

Turning On the ABX-N300........................... 14

Selecting the Input Source .......................... 14

Adjusting the Volume................................... 14

About Internet Radio and Media Servers ......32

Internet Radio Function................................32

Media Server Function.................................32

Server Requirements...................................32

Muting the ABX-N300

(remote controller only) ............................. 14

Changing the Downlight Brightness

(remote controller only) ............................. 14

Troubleshooting ..............................................33

Power...........................................................33

Audio............................................................33

iPod/iPhone..................................................33

Network........................................................34

Internet Radio ..............................................34

Adjusting the Bass and Treble

(remote controller only) ............................. 15

Using Super Bass

(remote controller only) ............................. 15

Using Headphones...................................... 15

Playing Music Files Saved on a

Network Server or Computer.....................34

Silencing the beep tone during operation

(remote controller only) ............................. 15

Can’t view the ABX-N300’s Information

in your Web Browser .................................34

Playing Your iPod/iPhone .............................. 16

Navigating the iPod/iPhone Menus ............. 17

AirPlay..........................................................34

Random Playback

(remote controller only) ............................. 17

Rocketboost™

(North American models only)...................35

Repeat Playback

(remote controller only) ............................. 17

Remote Controller........................................35

External Components ..................................35

Timers..........................................................35

Using the AirPlay......................................... 17

Listening to Internet Radio............................. 18

Specifications ..................................................36

Receiving a Broadcast................................. 18

Playing Music Files on a Server .................... 19

Setting Up a Network Server....................... 19

Rocketboost™

(North American models only) ................... 21

Rocketboost Wireless Card Ready.............. 21

What is Rocketboost?.................................. 21

Typical Rocketboost Applications................ 21

Rocketboost Setup ...................................... 22

En-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Supplied Accessories

Make sure you have the following accessories:

❏

iPod/iPhone dock digital connection

AirPlay

Media server capability

Internet radio support

iPod/iPhone charging capability

Control your iPod/iPhone with the remote controller

Bass and treble tone controls

Super Bass (S.Bass) function for deeper bass sounds

Line input for external audio source

Downlight with adjustable dimmer

2 programmable timers

Remote controller (RC-806S) and battery (CR2025)

The lithium button battery (CR2025) is already installed

in the remote control when you purchase the ABX-N300.

Sleep timer

Snooze function

Rocketboost™ Expandable Wireless Audio

Technology receives wireless audio from

Rocketboost devices (Requires Rocketboost Wireless

Card, WLC-TR1, sold separately)

AC adapter (DC output 16V 3A)

(Adapter varies from country to country.)

(North American models only)

Note:

Use only the AC adapter included with the ABX-N300.

Using any other AC adapter may damage the

ABX-N300. The included AC adapter is only for use

with the ABX-N300. It cannot be connected to other

devices and used.

AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod classic,

iPod nano, iPod shuffle, and iPod touch are trademarks of Apple

Inc., registered in the U.S. and other countries.

“Made for iPod” and “Made for iPhone” mean that an electronic

accessory has been designed to connect specifically to iPod or

iPhone, respectively, and has been certified by the developer to

meet Apple performance standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod or iPhone

may affect wireless performance.

In catalogs and on packaging, the letter at the end of the product

name indicates the color. Specifications and operation are the same

regardless of color.

Windows and Windows Media Player are trademarks of Microsoft

Corporation registered in the USA and in other countries.

En-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote

Controller

Replacing the Battery

While sliding the stopper to the side, pull

Remove the plastic film before using the remote controller.

out the battery holder.

Back side

When using the remote controller, point it toward the

ABX-N300’s remote control sensor, as shown below.

Insert a lithium button battery in the battery

holder, and then replace the holder.

Remote control sensor

ABX-N300

Positive (+) side

Approx. 5 m

(16 ft.)

When replacing the battery

When you replace the battery, be sure to use the specified

type of battery.

Notes:

Battery holder

• The remote controller may not work reliably if the

ABX-N300 is subjected to bright light, such as direct

sunlight or inverter-type fluorescent lights. Keep this

in mind when installing.

• If another remote controller of the same type is used in

the same room, or the ABX-N300 is installed close to

equipment that uses infrared rays, the remote

controller may not work reliably.

• Don’t put anything, such as a book, on the remote

controller because the buttons may be pressed

inadvertently, thereby draining the batteries.

• The remote controller may not work reliably if the

ABX-N300 is installed in a rack behind colored glass

doors. Keep this in mind when installing.

• The remote controller will not work if there’s an

obstacle between it and ABX-N300’s remote control

sensor.

Required battery

3V lithium button battery

CR2025

Polarity

indication 

Battery model

number

Latch

Notes:

• If the remote controller doesn’t work reliably, try

replacing the battery.

• If you intend not to use the remote controller for a long

time, remove the battery to prevent damage from

leakage or corrosion.

• Expired batteries should be removed as soon as

possible to prevent damage from leakage or corrosion.

• Make sure that the battery is oriented in the correct

polarity (observe the “+” and “–” indication).

• Never use a battery of a different model number.

• If not handled correctly, a lithium battery may ignite

or chemically cause skin irritation. Keep lithium

batteries out of the reach of children.

Do not disassemble, recharge, or incinerate a lithium

battery, and do not allow it to reach a temperature

exceeding 100 °C (212 °F). When replacing the

battery, use only the specified type of battery. If you

use the wrong battery, you risk causing fire or

explosion.

En-8

Download from Www.Somanuals.com. All Manuals Search And Download.

About Your iPod/iPhone

■ Removing the Dock Adapter

iPod/iPhone Models that can be

Connected

As shown in the illustration below, insert a slotted

screwdriver or similar object into the slit of the dock

adapter, and lift the adapter up.

Compatible iPod/iPhone models

Made for:

• iPod touch (1st, 2nd, 3rd and 4th generation)

• iPod classic

• iPod nano (2nd, 3rd, 4th, 5th and 6th generation)

• iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Note:

Before you begin using it, please update your iPod/

iPhone to the latest version. For details, refer to the

Apple website.

■ About the Dock Adapter

The ABX-N300’s dock uses the Universal Dock system.

By attaching an interchangeable part called a dock

adapter, you’ll be able to insert your model of supported

iPod/iPhone.

• Use a commercially available dock adapter or the one

that was included with your iPod/iPhone.

Caution

• If you connect an iPod/iPhone to the ABX-N300

without attaching a dock adapter, you risk straining

and damaging the connector. Even if the dock adapter

is connected, you should avoid straining the connector

by moving or wiggling the connected iPod/iPhone.

• When inserting or removing your iPod/iPhone, take

care to insert or remove it in a straight line with the

angle of the connector, and do not use excessive force.

• Do not forcefully press the controls of your iPod/

iPhone while it is connected to the ABX-N300, or

wiggle your iPod/iPhone forward or backward. Doing

so will cause damage or faulty contacts in the

connector.

• If your iPod is a compact and lightweight model, and

has no compatible adapter, you may connect it directly.

Move the slide cover to the

left to expose the dock.

• Do not use the system in conjunction with other

accessories such as an FM transmitter or microphone.

Doing so may cause faulty operation.

Dock adapter

• If your iPod/iPhone is in a case, it might not be able to

fully connect with the connector, causing failure to

sound or inability to operate the remote control.

Remove your iPod/iPhone from its case before

inserting it in the ABX-N300.

First align the front

edge of the dock

adapter, and then

press down on the

rear edge.

En-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the ABX-N300

Top/Front Panel

The page numbers in parentheses show where you can find the main explanation for each item.

Open

6 7 8 9 j

a Slide cover

i [/] button (16, 20, 22)

Close the slide cover when transporting the

ABX-N300 or when not using the dock.

This button starts playback on the iPod/iPhone.

Pressing this during playback will pause the

playback.

b iPod/iPhone dock (9, 16)

j INPUT button (14, 17, 18, 20, 22)

Insert your iPod/iPhone here.

This button selects the source that will be heard.

c Display

k VOL []/[] buttons (14)

d MENU button (17, 19)

This button displays the menu, or returns to the

previous screen.

These buttons adjust the volume.

l ON/STANDBY [] button (14, 22)

This button switches the power between on/standby.

e []/[] buttons (17, 18, 20)

When the menu is displayed, use these buttons to

select a menu item.

m Network standby indicator (30)

If the standby mode is set to “Network,” this

indicator will light orange when the ABX-N300 is

in standby mode.

f ENTER button (17– 20)

Press this button to confirm a setting you’ve made in

a menu, etc.

n Stand

g [] button (19)

o Downlike (14)

This button takes you back to the previous menu.

This will be lit when the power is on, and unlit in

standby mode.

h [] button (20)

This button stops playback.

En-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the ABX-N300—Continued

Rear Panel

The page numbers in parentheses show where you can find the main explanation for each item.

Bottom

Rear Panel

2 3 4

a Wireless LAN antenna (13, 27)

e AC adapter jack (DC IN 16V 3A) (13)

Unfold this antenna if you’re connecting to the

network wirelessly.

Connect the included AC adapter here.

f Rocketboost™ Module Slot

b ETHERNET port (13, 28)

(North American models only) (22)

Insert Rocketboost Wireless Card here if you’re

using the Rocketboost wireless digital audio.

Connect your Ethernet cable here if you’re

connecting to the network via a cable.

c [] Headphones jack (13, 15)

You can connect the stereo mini-plug of your

headphones here.

d LINE IN jack (13)

Use a commercially available stereo mini-plug

audio cable to connect an external device’s audio

output to this jack. This allows the ABX-N300 to

play back audio from a device such as a portable

audio player, game device, television, or record

player with built-in phono equalizer.

About Installation

The ABX-N300 features a speaker bass reflex duct on each side panel. Allow a space of 20 cm or more on each side

to avoid blocking the bass sound.

En-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the ABX-N300—Continued

Remote Controller (RC-806S)

The page numbers in parentheses show where you can find the main explanation for each item.

h TONE button (15)

Press this button when you want to adjust the bass

(low range) or treble (high range).

i S.BASS (Super Bass) button (15)

This button lets you make Super Bass settings.

j VOLUME []/[] buttons (14)

These buttons adjust the volume.

k MUTING button (14)

This button temporarily silences the sound.

l REPEAT button (17)

During iPod/iPhone playback, this button makes the

songs play repeatedly.

m SHUFFLE button (17)

During iPod/iPhone playback, this button makes the

song play randomly.

n PLAYLIST []/[] buttons

These buttons are not used.

o [/] button (16, 17, 20, 22)

This button starts playback. During playback, you

can press this button to pause.

p [] button (19, 23, 25, 28, 30)

This button takes you back to the previous menu.

q []/[] buttons (16, 20, 25, 28, 29)

These buttons select the previous or next song.

r ENTER button (15, 17–20, 23–25, 27–31, 33)

Press this button to confirm a setting you’ve made in

a menu, etc.

a [] (on/standby) button (14, 22, 23, 24, 27,

28)

s MENU button (15, 17, 19, 27, 29–31, 33)

This button displays the menu, or returns to the

previous screen.

This button switches the power between on/standby.

b TIMER button (23–25)

t []/[] buttons (15, 17, 18, 20, 23–25, 27–31,

This button lets you set the clock and timer.

33)

c SLEEP button (25)

When the menu is displayed, use these buttons to

select a menu item.

This button is used to set the sleep timer.

d SNOOZE button (25)

u DIMMER button (14)

This button switches the brightness of the

downlight.

Press this button to use the snooze function

(temporarily stopping timer playback).

e DISPLAY button (20, 23)

The information (album title, artist name) shown in

the display will change each time you press this

button. If you press this button when the

ABX-N300 is in standby mode, the clock will be

displayed for eight seconds.

f INPUT []/[] button (14, 17, 18, 20, 22)

This button selects the source that will be heard.

g [] button (20)

This button stops playback.

En-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Before you make connections

• This illustration is only one example. The connection method is the same even if you’re using other devices. Be sure

to also read the owner’s manual of the device you’re connecting.

• Don’t connect the AC adapter until you’ve finished making all connections.

Unfold the antenna if you’re

connecting to the network

wirelessly.

WirelessLAN

router

Internet

Modem

Stereo mini-plug

Stereo

Connect the audio output jacks of your

external device to the LINE IN jack. The

ABX-N300’s jack is a stereo mini-jack.

Use a commercially-available cable

that’s appropriate for the jack(s) of the

device you’re connecting.

WAN

mini-plug

LAN

Router

* Use a connection cable that does not

contain a built-in resistor.

Included AC adapter

Earphone jack or

audio output jack

Caution

Use only the included

AC adapter. Do not use

the included AC

adapter with any other

device. Doing so may

cause malfunctions or

accidents.

Portable audio

player etc.

* If the volume is

insufficient, raise

the volume of the

connected device.

Stereo

mini-plug

Computer

Analog audio

output jacks

RCA plug

White

Headphones

Game console

Red

Television

Record player with built-in

phono equalizer

Caution

If you connect the earphone jack of another device to the ABX-N300’s LINE IN jack, you must first adjust the volume

of the connected device.

En-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operation

ꢀ

DIMMER

INPUT ꢃ/ꢄ

ꢂ ꢁ

TONE

S.BASS

ENTER

INPUT

VOLUME ꢂ/ꢁ

VOL ꢁ/ꢂ

ꢀON/STANDBY

Downlight (below the speakers)

MUTING

Buttons on the top panel can be operated via the touch

screen.

Muting the ABX-N300

(remote controller only)

To mute the ABX-N300, press the remote controller’s

[MUTING] button.

Turning On the ABX-N300

To turn on the ABX-N300, press the [] button on the

ABX-N300 or remote controller.

“Muting” will appear on the display.

To unmute the ABX-N300, press the [MUTING] button

again.

The power will turn on, and the downlight located in the

lower part of the ABX-N300 will illuminate.

Press the [] button again to set the ABX-N300 to

Muting will also be disabled in the following cases.

standby.

• When you adjust the volume

• When you enter standby mode, and then turn the

power on again

Selecting the Input Source

Press the ABX-N300’s [INPUT] button or the remote

controller’s INPUT []/[] button to switch the input

source for playback.

Changing the Downlight Brightness

(remote controller only)

You can choose from iPod, Rocketboost™ (North

American models only), LINE (the connected external

device), Internet Radio, Media Server, or AirPlay. Each

time you press the [INPUT] button, the input will cycle

through the following choices.

You can adjust the brightness of the downlight.

Press the remote controller’s [DIMMER] button.

Each time you press the button, the brightness will cycle

through the following settings.

Bright

(default setting)

Dim

Off

Rocketboost

(North American

models only)

iPod

LINE

AirPlay

Internet Radio

Media Server

Adjusting the Volume

Press the VOL [] button to increase the volume or the

VOL [] button to decrease it.

You can also use the remote controller’s VOLUME []/

[] buttons.

You can adjust the volume in the range of “0” – “39,” and

“Max.”

En-14

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operation—Continued

Adjusting the Bass and Treble

(remote controller only)

Using Headphones

You can connect a pair of stereo headphones (ø3.5 mm,

1/8-inch phone plug) to the ABX-N300’s headphones

[] jack (see page 11) for private listening.

Note:

Tone adjustments (Bass, Treble, S.Bass) do not affect the

headphones.

Notes:

• Always turn down the volume before connecting your

headphones.

Press the [TONE] button to make the

display indicate “Tone Control.”

The value of the Bass setting will blink.

• If headphones are connected, no beep will be heard

when you operate the touch screen of the ABX-N300.

• While the headphones plug is inserted in the

headphones [] jack, the speakers are turned off.

• If the input is set to iPod or Rocketboost™ (North

American models only), no sound will be output from

the headphones. Disconnect the headphones and listen

via the speakers.

Use the []/[] buttons to adjust the value.

You can adjust the value in the range of –3 to +3.

Note:

If you press no buttons for eight seconds, the

previous display will appear automatically.

Silencing the beep tone during

operation (remote controller only)

Press the [ENTER] button.

The value of the Treble setting will blink.

You can silence the beep tone that is heard when you

operate the touch screen of the ABX-N300.

Use the []/[] buttons to adjust the value.

You can adjust the value in the range of –3 to +3.

Note:

While the ABX-N300 is in standby mode,

press the remote controller’s [MENU]

button.

If you press no buttons for eight seconds, the

previous display will appear automatically.

Press the [ENTER] button.

Use the []/[] buttons to select “Beep,”

and press the [ENTER] button.

The original display will reappear.

Use the []/[] buttons to select “Off,” and

press the [ENTER] button.

Using Super Bass

(remote controller only)

To turn on Super Bass, press the [S.BASS] button.

The “S.BASS” indication will appear on the display.

Tip:

If you want to re-enable the beep tone, choose “On” in

step 3 of the procedure above.

.BASS

The strength of the ultra-low range will change each time

you press the [S.BASS] button.

The “S.BASS” indication will disappear when this

setting is off.

S.Bass Off

(default setting)

S.Bass On

En-15

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Your iPod/iPhone

INPUT ꢃ/ꢄ

ꢅ/ꢆ

ENTER

ꢂ/ꢁ

ꢄ/

Slide cover

ꢂ/ꢁ

ENTER

ꢄ/

INPUT

SHUFFLE

REPEAT

Notes:

• Before using your iPod/iPhone with the ABX-N300,

be sure to update your iPod/iPhone with the latest

software, available from the Apple website.

• If you leave your iPod/iPhone paused when using it on

its own, eventually it will go into hibernation. If you

insert it into the ABX-N300 dock in this state, you’ll

need to wait a few moments before your iPod/iPhone

is ready for use.

• To prevent damage to the dock connector, do not

twist or force your iPod/iPhone into the dock, and

be careful not to wiggle your iPod/iPhone while

inserting it.

• If you use a case with your iPod/iPhone, always

remove it before you insert it. Otherwise, it may

not connect properly and a malfunction may

occur.

• Always remove your iPod/iPhone before moving the

ABX-N300.

• Depending on your iPod/iPhone, or the type of content

being played, some functions may not work as

expected.

• Do not close the slide cover while an iPod/iPhone

is inserted. We recommend that you leave the

slide cover closed when not using the

ABX-N300.

• Do not use with any iPod/iPhone accessories,

such as FM transmitters and microphones, as they

may cause a malfunction.

Move the slide cover to the left.

Press the [/] button.

Playback will start.

Power-on the ABX-N300, and select “iPod”

as the input source.

Insert your iPod or iPhone into the iPod/

iPhone dock.

Pausing Playback

To pause playback, press the [/] button.

Press the button once again to resume playback from

where you paused.

Dock for iPod/iPhone

iPod/iPhone

Selecting Songs (remote controller only)

To return to the beginning of the track that’s currently

playing or paused, press the [] button.

Press the [] button repeatedly to select earlier songs.

Press the [] button repeatedly to select subsequent

songs.

Fast Forward and Fast Reverse

(remote controller only)

To fast forward or fast reverse during playback or while

playback is paused, press and hold down the [] or

[] button, respectively.

Insert your iPod/iPhone securely into the

ABX-N300’s dock.

If you use a dock adapter, refer to page 9.

En-16

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Your iPod/iPhone—Continued

Navigating the iPod/iPhone Menus

Using the AirPlay

With this unit, you can enjoy the music of iOS-based

devices or iTunes music library using Apple Inc.’s AirPlay.

Press the [MENU] button on the ABX-N300

or the remote controller to display the

menu/list on the iPod/iPhone.

Note:

To use AirPlay, you’ll need one of the following

equipments.

Use the []/[] buttons to select an item on

the menu, and then press [ENTER].

• iPod touch, iPhone, iPad with iOS 4.2 or greater

• A personal computer with iTunes 10 (or greater)

installed

Tips:

Random Playback

• Before you use this feature, you must update your

iPod touch/iPhone/iPad to the latest version.

• For optimal performance, we recommend you always

use the latest version of iOS and iTunes.

• For details on AirPlay or how to obtain the latest

version for your software, please visit Apple web site.

(remote controller only)

With random playback, the songs on the iPod/iPhone are

played in random order.

Press the [SHUFFLE] button.

The  symbol will appear in the screen of the

iPod/iPhone.

To start random playback, press the [/]

button.

Random playback will start.

AirPlay, the AirPlay logo, iPad, iPhone, iPod,

iPod classic, iPod nano, iPod shuffle, and iPod touch are

trademarks of Apple Inc., registered in the U.S. and other

countries.

Cancelling Random Playback

To cancel random playback, press the [SHUFFLE]

button.

Caution

In order to using the AirPlay, the ABX-N300 must be

connected to a network. For details on connecting to a

network, refer to “Network Setup” (see page 26).

The  symbol will disappear from the screen of the

iPod/iPhone.

Playback

Repeat Playback

(remote controller only)

Follow the procedure below to play back.

If you press the [REPEAT] button, the song on the iPod/

iPhone will play repeatedly. The type of repeat playback

will change as follows each time you press the

[REPEAT] button.

Select “AirPlay” as the input.

Use the ABX-N300’s [INPUT] button or the

remote controller’s INPUT []/[] buttons to

select “AirPlay.”

 : Repeat one song

From the AirPlay icon [] of iTunes or your

iPod touch/iPhone/iPad, select “Onkyo

ABX-N300 ******” (default setting).

 : Repeat all songs

Cancelling Repeat Playback

Press the [REPEAT] button several times until the  or

 symbol disappears from the screen of the iPod/

iPhone.

Start playback in iTunes or on your iPod

touch/iPhone/iPad.

Notes:

• If there’s no sound via AirPlay, temporarily select

something other than the ABX-N300 from [], wait

for a while, and then select the ABX-N300 once again.

• Elapsed time or other indicators may not be displayed

correctly.

En-17

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to Internet Radio

The ABX-N300 supports vTuner Internet Radio.

INPUT ꢃ/ꢄ

ENTER

ꢇ

ꢂ/ꢁ

INPUT

ENTER

Caution

Use the []/[] buttons to select “United

Kingdom,” and press the [ENTER] button.

In order to listen to Internet radio, the ABX-N300 must

be connected to a network. For details on connecting to

a network, refer to “Network Setup” (see page 26).

“United Kingdom” is merely an example. You are

free to select any country you like, not just “United

Kingdom.”

Receiving a Broadcast

Select “Internet Radio” as the input.

United Kingdom

+ All Stations

1/ 50

Use the ABX-N300’s [INPUT] button or the

remote controller’s INPUT []/[] buttons to

select “Internet Radio.”

A list of Internet radio stations will be automatically

loaded from the vTuner radio station database

service.

Use the []/[] buttons to select the genre

that you want to hear, and press the

[ENTER] button.

If you don’t want to choose a genre, leave “All

Stations” selected and simply press the [ENTER]

button.

Internet Radio

+ Favorites

1/ 8

Use the []/[] buttons to select a station,

and press the [ENTER] button.

Use the []/[] buttons to select “Stations

By Location,” and press the [ENTER]

button.

The ABX-N300 will automatically connect to the

station, data will be loaded, and playback will

begin.

“Stations By Location” is merely an example. You

are free to select any item.

Music Now

BGM

Buffering

Use the []/[] buttons to select “Europe,”

and press the [ENTER] button.

“Europe” is merely an example. You are free to

select any region you like, not just “Europe.”

70%

En-18

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to Internet Radio—Continued

Tips:

Make a note of the ABX-N300’s MAC

Address (see page 30).

• The “+” shown at the left edge indicates a folder.

By pressing the [ENTER] button at the “+”

indication, you can move to the level below.

The “>” indicates a broadcast station. When you

press the [ENTER] button at the “>” indication,

playback will begin.

Turn on the power of the ABX-N300, and

switch the input to “Internet Radio.”

The vTuner menu “+ Favorites” will appear. If this

menu does not appear, check the network

connections and settings.

• By pressing the [MENU] button, you can return

to step 1 and select a station.

• By pressing the [] button, you can return to

the previous step and re-select the station.

• “Recent Launches” contains the stations that you

recently listened to.

Use your computer’s browser to access

http://onkyo.vtuner.com/.

as the ID#.

Caution

Internet radio cannot be paused.

Enter only the 12 alphanumerical digits, omitting

any “-” (hyphen).

As directed in the screen, register “Favorites” or

“My Added Stations.”

Using “Favorites” and “My Added Stations”

of vTuner Internet Radio

The stations you registered will be available in

“Favorites” or “My Added Stations” in the

ABX-N300’s vTuner menu.

You can save your favorite radio stations in vTuner’s

“Favorites” and “My Added Stations.”

Playing Music Files on a Server

This section explains how to play music files on a computer or media server through the ABX-N300 (Server Playback).

DISPLAY

INPUT ꢃ/ꢄ

ꢈ

ꢅ/ꢆ

ENTER

ꢄ/

ꢂ/ꢁ

INPUT

ꢂ/ꢁ

ꢈ

ꢄ/

ENTER

Caution

Setting Up a Network Server

The ABX-N300 must be connected to a network. For

details on connecting to a network, refer to “Network

Setup” (see page 26).

This section explains how to configure Windows

Media Player 11/12 so that the ABX-N300 can play the

music files stored on your computer.

En-19

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Music Files on a Server—Continued

Windows Media^®Player 11 Setup

Playing Music Files

Start your computer or media server.

Start Windows Media Player 11.

Start up the ABX-N300, and set the input to

“Media Server.”

On the “Library” menu, select “Media

Sharing.”

Press the ABX-N300’s [INPUT] button or use the

remote controls INPUT []/[] buttons to select

“Media Server.”

The “Media Sharing” dialog box will appear.

Select the “Share my media” check box,

and then click “OK.”

A list of network servers will appear.

Use the []/[] buttons to select the

network server that you want to use, and

then press the [ENTER] button.

Select the ABX-N300 in the list, and then

click “Allow.”

Click “OK” to close the dialog box.

Notes:

• The ABX-N300 cannot access photos or videos

on a network server.

• Some content might not be displayed depending

on the sharing settings of the network server.

Refer to the owner’s manual of the network

server.

This completes the Windows Media Player 11

configuration.

You can now play the music files in your Windows

Media Player 11 library through the ABX-N300.

Windows Media Player 11 can be downloaded for

free from the Microsoft web site.

Use the[]/[] buttons to select the music

file that you want to hear, and press the

[ENTER] button.

Windows Media^®Player 12 Setup

Playback will start.

Tips:

Start Windows Media Player 12.

• The “+” mark shown at the left edge indicates a

folder. By pressing the [ENTER] button at the

“+” mark, you can move to the lower level. The

“>” mark indicates a file. When you press the

[ENTER] button at the “>” mark, playback will

begin.

• Press the [MENU] button to resume from Step 2.

• By pressing the [] button, you can return to

the previous step and again select a file.

On the “Stream” menu, select “Turn on

media streaming.”

A dialog box will appear.

Move your cursor and click on “Turn on

media streaming.”

A list of media server will appear. Wording may

vary slightly depending on the network location.

Select the ABX-N300 in the list, and then

click “Allowed.”

Pausing Playback

To pause playback, press the [/] button.

Press the [/] button again to resume playback from

the pause point.

Click “OK” to close the dialog box.

This completes the Windows Media Player 12

Stopping Playback

To stop playback, press the [] button.

configuration.

You can now play the music files in your Windows

Switching to the previous or next song

To switch songs, use the remote controller’s [] or

[] buttons.

Media Player 12 library.

Switching the information display

Press the remote controller’s [DISPLAY] button

repeatedly to toggle the information display between

album title and artist name.

En-20

Download from Www.Somanuals.com. All Manuals Search And Download.

Rocketboost™ (North American models only)

The ABX-N300 can play back music from another

Rocketboost device (Sender).

Typical Rocketboost Applications

Rocketboost Wireless Card Ready

Send audio from MP3 or PC

Installing a Rocketboost

Wireless Card (sold

separately) enables this

product to receive wireless

audio from your other

Rocketboost products.

Rocketboost

Sender

What is Rocketboost?

Rocketboost is expandable wireless digital audio.

ABX-N300 with WLC-TR1

• Products with Rocketboost technology let you easily

expand your listening experience throughout your

home.

• Rocketboost does not interfere with other wireless

products in your home.

• Rocketboost is uncompressed digital audio

compatible with all audio formats.

When you see the Rocketboost logo on any product, it

has been designed to work with other Rocketboost

products, no matter who manufactures them.

How Can I Use Rocketboost with the

ABX-N300?

Rocketboost Wireless Card

(WLC-TR1, sold separately)

A Rocketboost Wireless Card (WLC-TR1, sold

separately) can be used to receive any Rocketboost audio

stream from your other Rocketboost products. For

example, you can play music from audio sources that are

in other rooms.

You can learn more about Rocketboost products at

www.rocketboost.com.

En-21

Download from Www.Somanuals.com. All Manuals Search And Download.

Rocketboost™ (North American models only)—Continued

Pairing

Rocketboost Setup

Rocketboost products form an audio network. Every

Initial Rocketboost Setup

Rocketboost network must contain one hub device,

which helps devices join the network. To add the

ABX-N300 to your Rocketboost network, you need to

pair it with your hub device.

Insert the WLC-TR1 into the Rocketboost Module Slot

on the back of the ABX-N300.

Note:

The ABX-N300 must be in standby mode when you

attach the Rocketboost Wireless Card (WLC-TR1, sold

separately). If the ABX-N300 is powered-on, press the

[] button to put it in standby mode.

Insert the Rocketboost Wireless Card

(WLC-TR1, sold separately) to the

ABX-N300.

Take care that the connector is oriented correctly,

and insert it all the way.

Power-on the ABX-N300, and set the input

to “Rocketboost.”

Use the ABX-N300’s [INPUT] button or the

remote controller’s INPUT []/[] buttons to

select “Rocketboost.”

Refer to the owner’s manual for your hub

device for the relevant pairing information,

then pair the ABX-N300 with the hub device.

Hold down the [] button on the ABX-N300

until the Status indicator of the

Rocketboost Wireless Card (WLC-TR1, sold

separately) is lit.

While pairing is occurring, the display will indicate

“Pairing” and the Status indicator will blink.

Reception will begin when the Status indicator has

changed from blinking to steadily lit, and pairing

has been completed.

When pairing is complete, the ABX-N300 is now

part of your Rocketboost wireless network and it

can receive audio from other Rocketboost sender

devices. The Rocketboost network can include a

total of nine devices (any combination of sender

and receiver devices). The maximum number of

wireless audio stream being sent over the network

at the same time is five.

Turn on the audio source connected to the

Rocketboost wireless sender.

Make sure the volume of the audio source is turned

up and not muted, otherwise no audio will be sent

over the Rocketboost network. You can also adjust

the volume level at the ABX-N300.

Tips:

If you have multiple audio sources in your Rocketboost

network, press the [/] button to hear the next audio

source. Press the [/] button again to cycle through all

available audio sources.

En-22

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Clock (remote controller only)

ꢀ

DISPLAY

TIMER

ꢇ

ENTER

ꢂ/ꢁ

Setting the Time and Day of the Week

Use the []/[] buttons to set the “day of the

week.”

While the ABX-N300 is in standby mode,

press the [TIMER] button.

Press the [ENTER] button.

If the ABX-N300 is powered-on, press the []

button to enter standby mode.

The setting will be completed, and then the display

will return to the standby condition.

Use the []/[] buttons to select “Clock

Setup.”

Cancelling without setting the time

Press the [TIMER] button.

Timer1 Setup

Timer2 Setup

Clock Setup

Returning to the previous screen

Press the [] button.

Caution

If the power supply is interrupted by a power failure or

by disconnecting the AC adapter, “--:--” will be

displayed, and the clock will stop. If this occurs, set the

clock again.

Press the [ENTER] button.

Use the []/[] buttons to set the time, and

press the [ENTER] button.

Displaying the Clock

If you hold down the []/[] buttons, the value

If you press the [DISPLAY] button while in standby

mode, the clock and day of the week will be shown for

approximately eight seconds.

will change continuously.

To switch between 12-hour and 24-hour display,

press the [DISPLAY] button.

Clock Setup

10:15

Sunday

En-23

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers (remote controller only)

The ABX-N300 provides three different timers: two program timers that can automatically play your iPod/iPhone at the

specified time, and a sleep timer that can put the unit in standby mode after the specified duration has elapsed.

ꢀ

SNOOZE

SLEEP

TIMER

ꢅ/ꢆ

ENTER

ꢇ

ꢂ/ꢁ

About the Timers

While the ABX-N300 is in standby mode,

press the [TIMER] button.

If the ABX-N300 is powered-on, press the []

Selecting the timer number

You can set up to two timers.

button to enter standby mode.

Setting the time

You can set the timer-on time and timer-off time.

Timer1 Setup

Timer2 Setup

Clock Setup

Specifying the day of the week

You can choose “Everyday” to make the timer operate

each day, or choose “Every” and specify the days of the

week on which the timer will operate.

Setting the playback volume

You can specify the volume for timer playback.

Use the []/[] buttons to select “Timer1

Setup” or “Timer2 Setup,” and press the

[ENTER] button.

Setting a Timer

Caution

Timer1 Setup

Timer1 On

• If the operating time of the two timers overlaps, the

timer that would have turned on later will not operate.

Please leave at least one minute between the off-time

of the first timer and the on-time of the second timer.

• If you’ve set the sleep timer within the time that a

timer had turned the power on, the power will operate

according to the sleep timer.

Off

6:30

7:00

Use the []/[] buttons to select “Timer1

On” or “Timer2 On,” and press the [ENTER]

button.

• Insert your iPod/iPhone into the iPod dock, and

prepare it for playback.

Use the []/[] buttons to set the timer-on

time, and press the [ENTER] button.

Use the []/[] buttons to set the timer-off

time and press the [ENTER] button.

En-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers (remote controller only)—Continued

Switching the Timer On (active) / Off

(disabled)

Use the []/[] buttons to select “Everyday”

or “Every,” and press the [ENTER] button.

^{If you selected “Everyday,” proceed to step}8.

Press the [TIMER] button.

Timer1 Setup

Every

MoTuWeThFrSaSu

Use the []/[] buttons to select “Timer1

Setup” or “Timer2 Setup,” and press the

[ENTER] button.

Use the []/[] buttons to select “On” or

“Off,” and press the [ENTER] button.

If you selected “Every,” use the []/[]

buttons to move to the day of the week that

you don’t want the timer to operate, and use

the []/[] buttons to make an underline

character appear. When you’ve finished

making the desired setting for each day of

the week, press the [ENTER] button.

The timer will not operate on days of the week that

are shown as an underline character. If you want

the timer to operate on a certain day of the week,

use the []/[] buttons to change the underline

character back to the weekday indication.

Press the [TIMER] button.

The clock will be displayed for a short time, and

then the ABX-N300 will enter standby mode.

Using the Snooze Function

When the timer has initiated playback, you can

temporarily stop playback by using the Snooze function;

playback will resume five minutes later.

To use the snooze function

During playback that has been started by the timer, press

the [SNOOZE] button.

Timer1 Setup

Every

TuWeThFrSaSu

Playback will temporarily stop, and will resume five

minutes later.

Using the Sleep Timer

The sleep timer automatically puts the ABX-N300 in

standby mode after the specified duration has elapsed.

Use the []/[] buttons to specify the

playback volume, and press the [ENTER]

button.

The timer indication and number will appear in the

upper right of the clock display; then after a time,

the ABX-N300 will switch to standby mode.

Press the [SLEEP] button.

The display will indicate “Sleep 90 min.” Each time you

press the [SLEEP] button, the setting will change in ten-

minute steps in the range of “Sleep 90 min” - “Sleep

10 min.” When the specified duration has elapsed, the

power will turn off.

Caution

In order for the timer to operate, the ABX-N300

must be in standby mode.

Checking the remaining time

When you press the [SLEEP] button, the display will

indicate the time remaining until the power will turn off.

However if the remaining time is less than ten minutes,

pressing the [SLEEP] button once again will cancel the

Sleep timer.

Cancelling without setting the timer

Press the [TIMER] button. You’ll return to standby

mode.

Returning to the previous screen

Press the [] button.

Cancelling the sleep timer

Repeatedly press the [SLEEP] button until the “Sleep

Off” indication appears.

Checking the timer setting

Press the [TIMER] button, then select “Timer1 Setup” or

“Timer2 Setup” and press the [ENTER] button

repeatedly to check the settings.

En-25

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup

In order to use the media server function (playing back music files saved on a computer), AirPlay, or Internet radio, the

ABX-N300 must be connected to a network.

The ABX-N300 can connect to the network in either of two ways: wirelessly or by a cable. You’ll need to make the

settings that are appropriate for the type of network you’re using.

Connect the ABX-N300 to your wireless LAN or wired LAN as described in “Connections” (page 13).

The ABX-N300’s wireless LAN conforms to Wi-Fi.

Network Essentials

A network is a setup in which multiple devices are connected by a cable (or wirelessly) so that they can communicate

with each other.

In a home, it is common to set up a network so that computers or game consoles can connect to the Internet, or so that

data can be transferred between multiple computers.

A network of this type that is limited to a relatively small area, such as a home, is called a Local Area Network (LAN).

If the ABX-N300 is connected to a network server such as a computer, it can play back music files stored on the network

server (computer), or connect to the Internet to play Internet radio.

In such cases, you do not connect the ABX-N300 directly to the other computer or to the Internet.

In order to connect to a computer or to the Internet, several other pieces of equipment (network devices) are required.

The following equipment is required in order to use the ABX-N300’s network functionality.

■ Router

A router is a device that sits between the ABX-N300 and a computer, or between the ABX-N300 and the Internet, and

controls the flow of data.

In a network, the flow of data is referred to as “traffic.” The router plays the role of a traffic controller between the

various devices.

• For use with the ABX-N300, we recommend a broadband router that contains a 100Base-TX switch.

• If you want to connect via wireless LAN, you’ll need to provide a wireless LAN router.

• If your router has DHCP functionality, it will be easy to make network settings.

• If you have a contract with an Internet Service Provider (ISP), use the router recommended by your ISP.

For more information about routers, please consult your dealer or your ISP.

■ Ethernet cable (CAT-5)

Ethernet cable is what is used to actually connect the devices making up the network. There are two types of Ethernet

cable: straight cables and cross cables.

• The ABX-N300 uses an Ethernet straight cable that complies with CAT-5 standards. Consult your dealer for more

information on Ethernet cables.

• If you’re connecting via a wireless LAN, an Ethernet cable is not needed.

■ Network server (such as a computer / if using a network server)

This is a device that stores music files and delivers them to the ABX-N300 for playback.

• The requirements for use with the ABX-N300 will differ depending on the device you’re using as a network server

(see page 32).

• For details about media servers supported by the ABX-N300, refer to page 32.

• The conditions for optimal playback of music files on the ABX-N300 will depend on the network server (the

performance of the computer) that you’re using. For details on each device, refer to the owner’s manual of the

corresponding device.

■ Internet Access (for Internet radio)

To receive Internet radio, your Ethernet network must have Internet access. A narrowband Internet connection (e.g.,

56 K modem, ISDN) will not provide satisfactory results, so a broadband connection is strongly recommended (e.g.,

cable modem, xDSL modem, etc). Please consult your ISP or computer dealer if you’re unsure.

Notes:

• To receive Internet radio with the ABX-N300, your broadband Internet connection must be working and able to access

the Web. Consult your ISP if you have any problems with your Internet connection.

• The ABX-N300 uses DHCP to configure its network settings automatically. If you want to configure these settings

manually, see “Network connections (Manual)” on page 29.

• The ABX-N300 does not support PPPoE settings, so if you have a PPPoE-type Internet connection, you must use a

PPPoEcompatible router.

• Depending on your ISP, you may need to specify a proxy server to use Internet radio. If your computer is configured

to use a proxy server, use the same settings for the ABX-N300 (page 30).

En-26

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup—Continued

Are you connecting to the

network by a cable or by a

wireless connection?

Cable

Wireless

Do you have a wireless LAN

router?

Do you have a router, or a modem

that includes router functionality?

Yes

See “Connecting via

Wireless LAN” below.

Obtain a wireless LAN

router.

Is DHCP enabled on your

router or router-capable

modem?

Obtain a router.

Yes

See “Network

connections(DHCP)” on

page 28.

See “Network

connections (Manual)”

on page 29.

Caution

Use the []/[] buttons to select “Standby

Mode,” and press the [ENTER] button; then

use the []/[] buttons to select “Network,”

and press the [ENTER] button.

• You’ll use the remote controller to perform these

operations.

• Network settings are made while the ABX-N300 is in

standby mode. If the ABX-N300 is powered-on, press

the [] button to put it in standby mode.

Standby Mode

Network

Connecting via Wireless LAN

Caution

• When setting up a wireless network connection, you’ll

need to enter the authentication method and security

key. Have these settings ready before you begin.

• Unfold the Wireless LAN antenna located on the back

of the ABX-N300.

Press the [MENU] button.

Use the []/[] buttons to select “Network

Setup,” and press the [ENTER] button.

Wait until the “Connection” indication appears.

Disconnect the AC adapter, wait at least ten

seconds, and then reconnect the AC

adapter.

Do not connect the Ethernet cable. If it is

connected, disconnect the Ethernet cable and the

AC adapter, and wait at least ten seconds before

reconnecting only the AC adapter.

Network Setup

Connection

Ethernet

Press the [MENU] button.

Network Setup

Network Info

Standby Mode

Beep

En-27

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup—Continued

Use the []/[] buttons to select “Wireless,”

and press the [ENTER] button.

The ABX-N300 will search for wireless LAN

access points, and will display the access points it

finds.

Move the cursor to “OK” and press the

10 _{[ENTER] button.}

Processing will be performed, and the system

will restart. Then the network connection will be

made.

If it succeeds, the display will indicate

“Succeeded”; if it fails, the display will indicate

“Failed.”

Network Setup

Select AP: 1/1

wireless ap

Tip:

If three minutes or longer have passed and the

ABX-N300 is still not connected to the network or if the

indication “Failed” is displayed, it may be that the

security type or the security key was not entered

correctly. In this case, try making the settings once again

from the beginning. If you have made the settings several

times and are still unable to connect, disconnect the AC

adapter, wait at least ten seconds before reconnecting it,

and then make the settings once again.

Note:

If an Ethernet cable is connected, you won’t be able to

select “Wireless.” If you want to connect via wireless

LAN, you must disconnect the Ethernet cable.

Use the []/[] buttons to select the access

point to which you want to connect, and

press the [ENTER] button.

Connecting via Wired LAN

Select the security type for the access

If you’re using a broadband router that supports DHCP

server functionality, the ABX-N300 will automatically

make IP address settings when you connect an Ethernet

cable.

point, and press the [ENTER] button.

Network Setup

Security Type

WPA-PSK(AES)

If you connect the ABX-N300 to a network that does not

support DHCP server functionality, you’ll have to

manually make settings such as the IP address.

Caution

For more about the security type, refer to the router

settings.

• You’ll use the remote controller to perform these

operations.

• Make network settings while the ABX-N300 is in

standby mode.

If the ABX-N300 is powered-on, press the [] button

to put it in standby mode.

• If you want to specify the network connection

manually, first check details on the settings.

• Depending on your Internet service provider, it might

not be possible for the connection to be made

automatically. If so, please make the settings manually.

Enter the security key.

Use the following buttons to enter characters.

[]/[] buttons: Move the cursor to left or

right

[ENTER] button: Enter one character

[]/[] buttons: Switch character groups

[] button: Delete the character immediately

before the cursor

Security Key

ABCDEFGHIJKLMNOP

QRSTUVWXYZ BS OK

Network connections (DHCP)

Disconnect the AC adapter, then connect

the Ethernet cable and wait at least ten

seconds before reconnecting the AC

adapter.

Characters that can be entered

Alphabetical: uppercase A–Z, lowercase a–z

Numerals: 0–9

Other characters: @ # $ % & ( ) _ - + = / ?

BS: Delete the character immediately before the

cursor

En-28

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup—Continued

Network connections (Manual)

Press the [MENU] button.

Disconnect the AC adapter, then connect

Network Setup

Network Info

Standby Mode

Beep

the Ethernet cable and wait at least ten

seconds before reconnecting the AC

adapter.

Press the [MENU] button.

Use the []/[] buttons to select “Standby

Mode,” and press the [ENTER] button; then

use the []/[] buttons to select “Network,”

Use the []/[] buttons to select “Standby

Mode,” and press the [ENTER] button; then

use the []/[] buttons to select “Network,”

and press the [ENTER] button.

Standby Mode

Network

Press the [MENU] button.

Use the []/[] buttons to select “Network

Setup,” and press the [ENTER] button.

Wait until the “Connection” indication appears.

Use the []/[] buttons to select “Ethernet,”

and press the [ENTER] button.

Press the [MENU] button.

Use the []/[] buttons to select “Network

Setup,” and press the [ENTER] button.

Wait until the “Connection” indication appears.

Use the []/[] buttons to select “Disable,”

and press the [ENTER] button.

Specify the “IP Address,” and press the

[ENTER] button.

Use the []/[] buttons to move the cursor,

and use the []/[] buttons to select numerals. The

following IP addresses can be specified.

Network Setup

Connection

Ethernet

Class A: “10.0.0.0”–“10.255.255.255”

Class B: “172.16.0.0”–“172.31.255.255”

Class C: “192.168.0.0”–“192.168.255.255”

Use the []/[] buttons to select “Ethernet,”

and press the [ENTER] button.

Specify the “Subnet Mask,” and press the

[ENTER] button.

Enter the subnet mask address provided by your

ISP (typically 255.255.255.0).

Network Setup

DHCP: Enable

Use the []/[] buttons to move the cursor,

and use the []/[] buttons to select numerals.

Specify the “Gateway,” and press the

10 _{[ENTER] button.}

Use the []/[] buttons to select “Enable,”

and press the [ENTER] button.

Processing will be performed, and the system will

restart. Then the network connection will be made.

If it succeeds, the display will indicate “Succeeded”;

if it fails, the display will indicate “Failed.”

Enter the gateway address provided by your ISP.

Use the []/[] buttons to move the

cursor, and use the []/[] buttons to select

numerals.

Specify the “DNS Server (Primary DNS,

11 _{Secondary DNS),” and then press the}

[ENTER] button.

Enter a DNS server address provided by your ISP.

Use the []/[] buttons to move the

cursor, and use the []/[] buttons to select

numerals.

En-29

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup—Continued

Caution

Specify the “Proxy Enable” setting, and

12 _{press the [ENTER] button.}

“Network Setup” and “Network Info” cannot be set or

viewed if “Standby Mode” is set to “Normal.” If you

want to set or view these settings, you must first set

“Standby Mode” to “Network.”

Use the []/[] buttons to select “No” or “Yes.”

Choose “No” if you are not using a proxy server.

If you are using a proxy server, choose “Yes,”

and then enter the Proxy URL.

Processing will be performed, and the system

will restart. Then the network connection will be

made. If it succeeds, the display will indicate

“Succeeded”; if it fails, the display will indicate

“Failed.”

Later, you can set “Standby Mode” to “Normal” if

desired.

Checking Network Information

Here’s how to view the IP address assigned to the

ABX-N300, as well as other information.

While the ABX-N300 is in standby mode,

press the remote controller’s [MENU]

button.

Cancelling without completing the settings

Press the [MENU] button.

All settings you had made up to this point will be

cancelled.

Use the []/[] buttons to select “Standby

Mode,” and press the [ENTER] button; then

use the []/[] buttons to select “Network,”

and press the [ENTER] button.

Returning to the previous setting item

Press the [] button.

You’ll return to the previous setting item.

Standby Mode

Network

About Standby Mode

There are two types of standby mode: “Normal” and

“Network.”

Network Setup

Network Info

Standby Mode

Beep

Press the [MENU] button.

Use the []/[] buttons to select “Network

Info,” and press the [ENTER] button.

Network Setup

Network Info

Standby Mode

Beep

In “Normal,” the network circuitry will also power-off in

standby mode, minimizing the electrical power

consumption. However when the power is turned on, the

ABX-N300’s power will turn on first, and then the

network circuitry will be powered and started up; this

means that it will take approximately 30 seconds before

functions related to the network or to your iPod/iPhone

will start operating.

The IP Address will be displayed. When you press

the [ENTER] button again, the MAC Address will

be displayed.

In “Network,” the network circuitry remains powered

even in standby mode; this means that functions related

to the network and to your iPod/iPhone will begin

operating immediately when the ABX-N300 is powered-

on. However, this will increase the amount of power used

while in standby mode up to approximately six watts.

If this is set to “Network,” the network standby indicator

(orange) will light when the ABX-N300 is in standby

mode.

En-30

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Setup—Continued

Editing the name shown in AirPlay

Viewing the “WEB Setup Menu”

Window

You can edit the ABX-N300’s name as it appears on a

network such as AirPlay.

If the ABX-N300 is connected to the network, you can

use a computer connected to that network to view and

edit the settings.

From the menu in the left side of the “WEB Setup

Menu” window, choose “Profile Configuration,” edit the

text in the “Digital Media Player Name” field, and press

the [Apply] button.

While the ABX-N300 is in standby mode,

press the remote controller’s [MENU] button.

Use the []/[] buttons to select “Network

Info,” and press the [ENTER] button.

The ABX-N300’s IP address will be displayed.

Start up a browser on your computer; in the

URL field, enter the IP address displayed in

step to access it.

The “WEB Setup Menu” window will appear.

En-31

Download from Www.Somanuals.com. All Manuals Search And Download.

About Internet Radio and Media Servers

Internet Radio Function

Internet radio refers to radio broadcasts that are distributed via the Internet. Numerous Internet radio stations from

around the world are being broadcast.

The ABX-N300 supports vTuner Internet Radio.

The ABX-N300’s list of Internet radio stations uses the vTuner radio station database service.

* vTuner may become unavailable without notice.

The ABX-N300’s Internet radio function can play the following audio file formats.

Format

Sampling frequency

Bit rate

MP3

WMA

AAC

32 kHz, 44.1 kHz, 48 kHz

32 kbps–320 kbps, VBR

Media Server Function

The ABX-N300 supports media servers; music files saved on a server or computer can be played back by the ABX-N300

via the network.

The ABX-N300 supports the following media server functionality.

• Communication protocol: UPnP-AV

• Device class: DMP

The ABX-N300’s media server function can play the following audio file formats.

Format

Sampling frequency

Bit rate

Extension

.mp3

MP3

32 kbps–320 kbps, VBR

WMA

.wma

32 kHz, 44.1 kHz, 48 kHz

.m4a

.aac

AAC

WAV

48 kbps–320 kbps

–

.wav

Server Requirements

The ABX-N300 can play digital music files stored on a computer or media server and supports the following

technologies:

• Windows Media Player 11

• Windows Media Player 12

The computer or media server must be on the same network as the ABX-N300.

Note:

Depending on the media server, the ABX-N300 may not recognize it, or may not be able to play its music files.

Tip:

If the operating system of your computer is Windows 7, Windows Media Player 12 is already installed.

If the operating system of your computer is Windows Vista , Windows Media Player 11 is already installed. Windows

Media Player 11 for Windows XP can be downloaded for free from the Microsoft website.

For more information, see the Microsoft website.

En-32

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you experience any problem while using the

ABX-N300, look for a solution in this section.

Audio

There’s no sound.

If a problem occurs with the ABX-N300’s operation, you

may be able to solve the problem by resetting the unit.

• Make sure the ABX-N300’s volume is not set too low

(see page 14).

Before you request service, please reset the

ABX-N300 as described below.

• Make sure the correct input source is selected

(see page 14).

• Make sure the ABX-N300 is not muted (see page 14).

• Check all connections and correct as necessary

(see page 13).

1. While the ABX-N300 is in standby mode, press

the remote controller’s [MENU] button.

2. Use the []/[] buttons to select “Reset,” and

press the [ENTER] button.

The sound quality is not good.

The screen will indicate “Cancel.”

• The sound quality can be affected by strong magnetic

fields, such as that from a TV. Try moving any such

devices away from the ABX-N300.

• If you have any devices that emit high-intensity radio

waves near the ABX-N300, such as a cellular phone

that’s being used to make a call, the ABX-N300 may

output noise.

3. If you decide not to reset, press the [ENTER]

button.

4. To reset, use the []/[] buttons to select

“Settings,” and press the [ENTER] button.

All settings other than the network settings will

return to their factory-set state, and the

ABX-N300 will enter standby mode.

Low range sounds are inaudible.

Note:

• Adjust the tone to your taste or according to the audio

source by activating S.Bass (see page 15).

• Allow a space of 20 cm or more on each side of the

unit (see page 11).

Selecting “Network” and then pressing the

[ENTER] button will reset network-related

functions. Perform this reset operation ONLY

when the unit’s network or iPod/iPhone does not

function properly.

iPod/iPhone

There’s no sound.

Power

• Make sure that your iPod/iPhone is playing.

• Make sure your iPod/iPhone is properly seated in the

ABX-N300’s iPod dock. (see pages 9 and 16).

• Disconnect your iPod/iPhone from the dock, and then

firmly insert it back into the dock.

• Make sure the ABX-N300 is turned on, the input

source is set to iPod, and the volume is not set too low.

• If your iPod or iPhone is in a case, remove the case

before inserting the iPod or iPhone (see page 9).

Can’t turn on the ABX-N300.

• Make sure that the AC adapter is properly plugged

into the wall outlet, and that the DC IN connection has

been made correctly (see page 13).

• Unplug the AC adapter from the wall outlet, wait ten

seconds or more, then plug it in again.

The ABX-N300 turns off unexpectedly.

Can’t control your iPod with the

ABX-N300’s remote controller.

• If the sleep timer has been set and the SLEEP

indication is shown on the display, the ABX-N300

will turn off automatically after a specified period

(see page 25).

• When timed playback finishes, the ABX-N300

automatically switches to standby mode

(see page 24).

• Make sure your iPod/iPhone is properly seated in the

ABX-N300’s iPod dock. Even very thin iPod/iPhone

cases can prevent the iPod/iPhone from seating

properly on the dock connector, so always remove any

case before inserting your iPod/iPhone

(see pages 9 and 16).

• Disconnect your iPod/iPhone from the dock, and then

firmly insert it back into the dock.

It takes a long time from power-on until

operation begins.

• It will take some time for functions related to the

network or to your iPod/iPhone to begin operating.

• If you set “Standby Mode” (see page 30) to

“Network,” the power consumption while in standby

mode will increase, but operation will begin

immediately when you turn the power on.

• Depending on your iPod/iPhone model, its software

version, or the content your playing, some functions

may not work as expected (see pages 9 and 16).

En-33

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

• To operate your iPod/iPhone using the remote

controller, point the remote controller toward the

ABX-N300’s remote control sensor (see page 8).

• Make sure that your router’s LAN port is correctly

connected to the ABX-N300.

• Make sure that the correct IP address is assigned in the

ABX-N300’s “Network Info” (see page 30).

• Depending on your ISP, you might need to make

proxy server setting.

Can’t recharge the iPod/iPhone.

• Make sure your iPod/iPhone is properly seated in the

ABX-N300’s iPod dock. (see pages 9 and 16).

• Disconnect your iPod/iPhone from the dock, and then

firmly insert it back into the dock.

• Make sure you’re using a router and modem that are

supported by your ISP.

• If your iPod or iPhone is in a case, remove the case

before inserting the iPod or iPhone (see page 9).

Playing Music Files Saved on a

Network Server or Computer

The indication “No Dock” or “Connecting”

remains even though your iPod/iPhone is

connected.

Network server or computer does not

display a list.

• Make sure that the network settings are correct

(see page 20).

• Disconnect your iPod/iPhone from the dock, and then

firmly insert it back into the dock.

• Power-off the ABX-N300, or disconnect the AC

adapter. Then turn on the power once again, and

connect your iPod/iPhone.

• Make sure that the router is set correctly.

• If the ABX-N300 is connected via a wireless LAN, the

state of the radio signal may make it impossible for the

ABX-N300 to connect to the server, or may cause the

connection to be interrupted. Try connecting via a

wired LAN.

Network

Can’t use the network server.

Can’t play back.

• Make sure that the network server has the correct

settings (see page 20).

• Is the file you’re attempting to play supported by the

ABX-N300 (see page 32)?

• Make sure that the network server is running.

• Make sure that the network server is correctly

connected to your home network.

• Make sure that the router’s LAN port is correctly

connected to the ABX-N300.

• If the ABX-N300 is connected via a wireless LAN, the

state of the radio signal may make playback

impossible, or may cause the audio to be interrupted.

Try connecting via a wired LAN.

• In order to play back music files from a computer,

• Make sure that the correct IP address is assigned in the

ABX-N300’s “Network Info” (see page 30).

you’ll need to start up Windows Media Player 11 or

12, and make settings for it (see pages 20).

Sound is interrupted while playing music

files from a network server.

AirPlay

No Sound during AirPlay playback.

• Make sure that the network server meets the operating

requirements (see page 32).

• After switching the input to something other than

“AirPlay,” pause iTunes or your iPod touch/iPhone/

iPad and wait at least ten seconds before resuming

playback.

• If you’re using a computer as the network server, try

closing all application software other than the server

software (such as Windows Media Player 12).

• The playback sound might be interrupted if your

computer is downloading or copying a large amount of

files.

• Click the AirPlay icon [] to temporarily disable the

iTunes or iPod touch/iPhone/iPad connection, and

then try reconnecting and playing back (see page 17).

• Try turning the ABX-N300’s power off and then on

again. Alternatively, disconnect the AC adapter, and

wait at least ten seconds before reconnecting it and

turning the power on again.

Internet Radio

Can’t listen to Internet radio.

• Try resetting the ABX-N300 (see page 33).

• Try restarting or resetting iTunes or your iPod touch/

iPhone/iPad.

• Make sure that the format being transmitted by the

radio station is supported by the ABX-N300

(see page 32).

• The radio station may be off air or overly busy. Try

again after a while.

• Check whether you can connect to the Internet from a

different device. If not, power-off all devices

connected to the network, wait for a while, and then

turn them on again.

En-34

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

• When connected via a wireless LAN, radio conditions

may make it impossible for the ABX-N300 to connect

to the server, or the audio might be interrupted, or the

image and audio might lose synchronization. Try

connecting via a wired LAN.

External Components

Insufficient volume from portable audio

player.

• Raise the volume on the portable audio player.

• Use a connection cable that does not contain a built-in

resistor.

Can’t operate AirPlay.

• In some cases you won’t be able to perform operations

from the ABX-N300 itself or using the buttons of the

remote controller. If so, perform the operations from

your iPod touch/iPhone/iPad.

• If you’ve switched the input to something other than

“AirPlay,” pause your iPod touch/iPhone/iPad and

wait at least ten seconds before resuming playback.

• If you turned the power off during AirPlay playback,

pause your iPod touch/iPhone/iPad and wait at least

ten seconds before resuming playback.

No sound is heard from your turntable.

• Make sure the turntable has a built-in phono equalizer.

If the turntable doesn’t have a phono equalizer built-

in, you must provide one.

• If you’re using a record player with an MC cartridge,

you’ll need a step-up transformer or a head amp.

Timers

• If multiple ABX-N300 units are playing

The timers don’t work.

simultaneously, AirPlay might not be controlled

correctly. Be careful not to let the remote control laser

beam be received by multiple ABX-N300 units.

• Are the clock and timer set correctly? Could there be

a mistake in the day of the week, the 24-hour/12-hour

time display setting, or the AM/PM setting

(see pages 23 and 24)?

Rocketboost™

(North American models only)

• The timer will not operate if the power is already on at

the start time. Make sure that the ABX-N300 is in

standby mode at the timer start time (see page 25).

• If the times of the two timers overlap, the timer that is

set later will not operate. Set the two timers to non-

overlapping times (see page 24).

Cannot connect to a Rocketboost network.

• If the joining process is failing, make sure that only

one of your Rocketboost wireless devices has the Hub

switch enabled.

• Make sure the timer is set to suitable volume setting

(see page 25).

• Make sure that you have installed the WLC-TR1

(sold separately).

• If “Standby Mode” is set to “Normal,” the system will

start up when the timer-on time arrives; this means

that it will be approximately 30 seconds later when

sound actually begins to play.

• Make sure that the link is established by Rocketboost

setup menu.

• The maximum number of Rocketboost devices in a

Rocketboost Network at the same time is five. If you

already have five devices and attempt to join another

one, then joining will fail for the new device. Power

down one of your devices and try again.

Clock is not shown in standby mode.

• Pressing the remote control’s [DISPLAY] button will

make the clock appear for eight seconds (see page 23).

• It’s not possible to make the clock remain displayed in

standby mode.

Remote Controller

The remote controller doesn’t work

properly.

The ABX-N300 contains a microcomputer. In very

rare situations, severe interference, noise from an

external source, or static electricity may cause it to

malfunction or lockup. In the unlikely event that this

should happen, unplug the AC adapter, wait at least ten

seconds, and then plug it back in again. If this doesn’t

resolve the issue, reset the ABX-N300 to its factory

defaults (see page 33).

• Replace the battery with a new one (see page 8).

• The ABX-N300’s remote control sensor is being

subjected to bright light (inverter-type fluorescent

light or sunlight) (see page 8).

• The ABX-N300 may malfunction if fluorescent light

bulbs in the room are wearing out and flickering.

Please check the fluorescent lights.

En-35

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

■ General

AC 100 V-240 V, 50/60 Hz

38 W

Power Supply:

Power Consumption:

Stand-by Power Consumption: 0.7 W (with “Standby Mode” set to “Normal,” and no iPod/iPhone connected)

Dimensions (W × H × D):

430 × 131 × 148 mm

(16-15/16 × 5-3/16 × 5-13/16 inches)

2.6 kg (5.7 lbs.)

Weight:

Analog Input:

LINE

■ Amplifier

Power Output:

2ch × 10 W (6 Ω, 1 kHz, 1% THD)

■ Speakers

Type:

Unit:

Full-Range bass reflex

6 cm (2-3/8") cone (magnetically shielded)

Specifications and features are subject to change without notice.

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650

http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4208-213

http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.

Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,

China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

http://www.cn.onkyo.com/

I1205-1

SN 29401122

* 2 9 4 0 1 1 2 2 *

Download from Www.Somanuals.com. All Manuals Search And Download.

MSi Computer Hardware MS 7304 User Manual
National Instruments Switch DIO 6533 User Manual
NEC Server 5800 320Fd User Manual
NHT Speaker VT 2 User Manual
Nikon Digital Camera S6500 User Manual
Nokia Network Card DNT2Mi fp User Manual
Omega Vehicle Security Stud Sensor OS1562 User Manual
Oregon Log Splitter S402022H0 S402022K0 User Manual
Parasound Stereo Amplifier 275 V2 User Manual
Parkside Cordless Drill PABS 108 A1 User Manual