Contents
9-Channel Amplifier
PA-MC5501
Instruction Manual
Thank you for purchasing an Onkyo 9-Channel
Amplifier. Please read this manual thoroughly before
making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 9-Channel Amplifier.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
• This unit’s top and rear panels may get warm after
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do
not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
extended period, remove the power cord from the AC
outlet.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME NMB-
003 DU CANADA.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
8. Handling Notes
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
En
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
Features
■ 150 Watts per channel, minimum RMS into
8 ohms, 2 channels driven, from 20 to 20,000 Hz
with no more than 0.05 % total harmonic
distortion
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
*1
■ THX™ Ultra2™ certified
Blue: Neutral
Brown: Live
■ WRAT–Wide Range Amplifier Technology
(5 Hz-100 kHz bandwidth)
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
■ Push-Pull amplification design with three-stage
inverted Darlington circuitry
■ Massive toroidal transformer
■ Customized 22,000 µF large capacitors for
effective power supply
■ Audio-tuned reference capacitors for each
channel
■ Low-impedance, copper bus plates for perfect
ground potential
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved
by ASTA or BSI to BS1362 and have the same ampere
rating as that indicated on the plug. Check for the ASTA
mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
■ Gold-plated, XLR and machined, solid brass
RCA input terminals
■ Custom-designed large power transistors to
drive high currents
■ High-current, low-impedance circuit board by
using thick copper foil (70 µ)
■ Gold-plated, color-coded, transparent speaker
posts
For European Models
Declaration of Conformity
■ Auto Standby function
*2
We,
ONKYO EUROPE
■ Multi-zone capability (up to Zone 3)
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
*2
■ Bi-amping capability
■ 12V trigger in
■ Aluminum front panel
■ Detachable power cord
*1
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
EN55013, EN55020 and EN61000-3-2, -3-3.
technical standards such as EN60065,
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
THX and Ultra2 are trademarks of THX Ltd. THX may be
registered in some jurisdictions. All rights reserved.
*2
Depends on AV controller.
En
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Supplied Accessories
Check that the following accessories are supplied with the
PA-MC5501.
Before using
Operations
Power cord
(Plug type varies from country to country.)
Connections
Mono mini-plug cable
(For connecting to the 12V trigger terminals.)
Appendix
Speaker cable labels
En
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Amplifier Precautions
Before using the PA-MC5501 power amplifier, be sure to
read the page above entitled Important Safety Instructions
and this page of Amplifier Precautions.
Care
From time to time you should wipe the front and rear
panels and the cabinet with a soft cloth. For heavier dirt,
dampen a soft cloth in a weak solution of mild detergent
and water, wring it out dry, and wipe off the dirt.
Following this, dry immediately with a clean cloth. Do not
use rough material, thinners, alcohol or other Chemical
solvents or cloths since these could damage the finish or
remove the panel lettering.
Whenever performing maintenance on the PA-MC5501,
any of its supplied accessories, or any device connected to
it, do not use solvents or cleaners of any kind that are
inflammable or combustible.
Ventilation
While using the PA-MC5501, the internal temperature
will fairly rise. Excessive temperature rise may affect the
amplifier performance. To prevent damage from occurring
due to high internal temperatures, it is vital to have proper
ventilation and passage of air to carry out the heat and
keep the internal temperature within acceptable ranges.
Caution
• Do not place the PA-MC5501 inside cabinets or closets where
there is poor passage of air and ventilation.
• Do not place the PA-MC5501 near external heat sources such as
heaters or hot air ducts.
When you clean the input/output terminals on the rear
panel, do not use contact restorer. Doing so may cause
resin deterioration.
• Do not place other components or object on top of or under the
PA-MC5501.
• The cover of the PA-MC5501 contains ventilation holes to allow
the passage of air. Do not cover or block these holes in any way.
Other
Below is a list of actions that you should never perform.
• Do not use the PA-MC5501 as a broadcast system or
musical instrument amplifier.
• Never use a generator, DC/AC converter, AC/AC
converter, or transformer to supply power for the
PA-MC5501.
If you are planning to place it within a cabinet, either open
holes in the rear panel of the cabinet to improve
ventilation or use a fan to force air circulation.
As a general rule, if during idling the cover is too hot to
touch, then ventilation needs to be improved.
• Never perform a “thumb test” (checking whether current
is reaching the lead wire on the hot end of the input by
touching it with your fingers) on the ends of the input
jacks or input cables.
Doing so may damage the speakers.
• Do not short across the output terminals or across the
output terminals and rear panel.
• Never remove the cover of the PA-MC5501.
• Do not install the PA-MC5501 in a location within the
reach of small children.
Installation location and space
Make sure that the floor or cabinet or rack where it will be
located is strong enough to support its weight.
You will also need to leave enough space behind the
PA-MC5501 to allow room for the power cord and other
cables for connecting system components. A minimum of
four inches is required behind the PA-MC5501 to allow
room for the cables and cords without excessively bending
them.
Do not place the PA-MC5501 near TV or radio. This may
cause noise or instable video on radio or TV respectively.
Lightning storms
During lightning storm, never touch the power cord, plug
or cover of the PA-MC5501, and any devices connected to
the PA-MC5501.
Power cord
Do not use a power cord other than the one supplied with
the PA-MC5501. The power cord supplied is designed for
use with the PA-MC5501 and should not be used with any
other device.
Be sure to only use wall sockets that properly fit the plug
of the power cord. If the socket does not match the plug of
the power cord, you will need to prepare an adapter.
Always use an adapter that is properly certified for this
application.
Power
WARNING:
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC
220-240 V, 50/60 Hz or AC 120 V, 60 Hz).
Speakers
Connected speakers should have an impedance of 4 ohms
or greater.
If speakers with an impedance of less than 4 ohms are
connected, it may damage the PA-MC5501.
En
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Quick Operation Guide
Here is a quick guide for those who want to listen to music
or view their favorite movies as soon as possible.
Connections and operations are explained briefly here for
the purpose of just getting you started.
1. Lower the volume at the control amplifier.
Lower the volume of the control amplifier to the
minimum so that when the amplifier is turned on, you
do not hear loud unwanted sounds.
2. Connect the speakers to the amplifier.
Connect the speakers to the amplifier using the proper
speaker cables. Be sure to match the channels and the
positive (+) and negative (–) polarities between the
speakers and the amplifier. If the connections are
mistaken, the correct orientation will not be obtained.
3. Select balanced input (XLR) or unbalanced input
(RCA) with the INPUT SELECT switch.
For those of you who want to operate the PA-MC5501
(the amplifier) right away, follow the guide below.
However, this instruction manual contains a great deal of
other information that you should know for the proper
operation of the amplifier and for a more pleasurable
experience with the amplifier. Be sure to read the rest of
this manual as well after reading this quick guide.
The procedures given below assume that the other system
components are already connected and configured. (For
example, that the source components are already
connected to the control amplifier.)
The amplifier possesses a balanced input (XLR) and
unbalanced input (RCA) for each channel and the
switch for the two is located between the two input
terminals. Select the proper input type depending on
the functionality of the connected cables and the
control amplifier.
Note
• Do not change the INPUT SELECT switch setting when the
amplifier is turned on.
4. Connect the control amplifier to the amplifier.
After selecting the correct input type in step 3 above,
connect the output from the control amplifier to the
corresponding input terminal on the amplifier.
Note
• Do not connect anything to the other input jack.
5. Connect the supplied power cord to the amplifier
and to the wall power outlet.
Be sure to properly plug the power cord all the way in.
6. Press the 8ON/STANDBY button.
The ON indicator flashes white for about 5 seconds
before it lights up.
When you connect other device to the 12V
TRIGGER IN terminal using the supplied cable, the
power on or off status of the amplifier synchronizes to
the action of turning on or off the connected device.
7. Slowly increase the control amplifier volume.
Note
• After the amplifier is turned on, it takes approximately
10 seconds before the output sounds. During this time, do not
turn up the volume.
Now all that remains is to control the control amplifier and
the other connected system components and enjoy your
music or movies.
En
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels
Front Panel
a
b
a 8ON/STANDBY button
This button is used to set the amplifier to On or
Standby.
b ON indicator
Once the main power of the amplifier has been turned
on, this indicator flashes white for about 5 seconds
before it lights up.
When it lights up, the amplifier is turned on and you
can enjoy an input source.
Note
• If you wish to turn on the amplifier again after it is set to standby,
wait for several seconds.
Note
• If the 8ON/STANDBY button is pressed and ON indicator do
not light, check that the power cord is properly connected. If the
indicator still doesn’t light, turn off the amplifier, disconnect the
power cord from the wall outlet, and contact your Onkyo dealer.
• If the power doesn’t turn on or immediately turns off upon
pressing the 8ON/STANDBY button, the protection circuitry
of the amplifier has activated. The protection circuitry activates
if a problem such as a speaker cable shorting or excessive
temperature occurs. Remove the power cord from the wall outlet
immediately. Make sure that all speaker cables and input sources
are properly connected, and leave the amplifier with its power
cord disconnected for 1 hour. After that, reconnect the power
cord and turn the power on. If the amplifier turns off again,
unplug the power cord and contact your Onkyo dealer.
WARNING
If smoke, smell or abnormal noise is produced by the
amplifier, unplug the power cord from the wall outlet
immediately and contact your Onkyo dealer.
En
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
This unit comprises 9 independent power amplifiers, each being capable of reproducing the same quality sound through
its channel. Note that you should connect an input source and a speaker to each channel in use.
Caution
• Do not connect the power cord until you have finished all other connections.
• Read the instructions that came with the other components you are connecting.
• Do not make connections to input or output jacks while the amplifier is turned on.
• Turn the volume of the control amplifier down before turning on the amplifier.
e f
g
h
a
b
c
d
Plugging the XLR cable
a Balanced Input (XLR terminal)
Match the pins and insert the terminal until you hear a
“click.” Make sure that the terminal is locked by lightly
pulling the connection cable.
Connect AV controllers or control amplifiers with
balanced outputs for high-quality sound.
1. GND
3. COLD
Unpugging the XLR cable
Pull out the connection cable while holding down the
lever.
2. HOT
Connector ground terminal: Chassis grounded
The pin assignments for this terminal are given above.
This pin assignment conforms to the standard adopted
by the Audio Engineering Society. Refer to the
instruction manual supplied with the control amplifier
and verify that its output terminal is compatible with
the pin assignments for this terminal. The output
terminal of Onkyo PR-SC5509 is compatible with the
pin assignments for the terminal of the amplifier.
Push
Note
• When using this balanced connection for a specific channel
between the control amplifier and the amplifier, set the INPUT
SELECT switch to the upper side (the balanced input side) to
select balanced input. Next, use commercial XLR balanced
cable and connect the balanced output from the control amplifier
to the corresponding balanced input on the amplifier.
The amplifier uses the European type XLR terminal.
Phase is reversed when an XLR cable is connected to
the control amplifier that uses the USA type XLR
terminal. In this case, swap pin 2 and pin 3 to set the
polarity to the European type before connecting.
• Do not connect anything to the RCA-type audio input jack.
En
9
Download from Www.Somanuals.com. All Manuals Search And Download.
b INPUT SELECT switch
g 12V TRIGGER IN
This switch is located between the balanced input and
single-ended RCA input for each channel. Use this
switch to select the input type for its channel.
When setting the switch to the upper side, the
balanced input is selected.
Connects to the 12V trigger output terminal on the
other component to control the amplifier. This enables
the amplifier to turn on or go into standby state based
on the power on/standby status of the connected
component.
When setting the switch to the lower side, the RCA
audio input is selected.
Use the supplied or commercially available 1/8-inch
mono cable to connect to the 12V trigger output
terminal on the other device.
Note
The tip polarity of the connectors are as shown below.
• Do not change the INPUT SELECT switch setting when the
amplifier is turned on.
• Make sure that connections have been made only to the inputs
selected with the INPUT SELECT switches and nothing is
connected to the other ones.
5 to 12 volts, positive
tip polarity
h AC INLET
c Unbalanced Input (single end RCA input)
Connect AV controllers or control amplifiers with
single-ended outputs.
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
Powercord
(supplied)
RCA type
Note
To an AC
wall outlet
• When using this single-ended connection for a specific channel,
set the INPUT SELECT switch to the lower side (the RCA
audio input side), use commercial RCA audio pin cable and
connect the single-ended outputs.
• Do not plug the amplifier into the AC outlet other than
an AC wall socket.
• Do not connect anything to the balanced input jack.
• Do not use a power cord other than the one supplied with
the amplifier. The power cord supplied is designed for
use with the amplifier and should not be used with any
other device.
• Never have the power cord disconnected from the
amplifier while the other end is plugged into the wall
outlet. Doing so may cause an electric shock. Always
connect by plugging into the wall outlet last and
disconnect by unplugging from the wall outlet first.
• Before you plug in the amplifier, confirm that all
connections have been made properly.
d OUTPUT (Speaker output and binding post)
These terminal posts are for connecting the front L/R,
center, surround L/R, surround back L/R, and
front high/wide L/R speakers.
The FRONT L/R and FRONT HIGH/WIDE L/R
terminal posts can be used with front speakers and
front high/wide respectively, or used to bi-amp the
front speakers. See “Bi-amping the Front Speakers”
e SPEAKER IMPEDANCE switch
Use this switch to select the speaker impedance.
• Turning on the power may cause a momentary power
surge, which might interfere with other electrical
equipment on the same circuit, such as computers. If this
happens, use a wall outlet on a different circuit.
4Ω: Select if the impedance of any speaker is 4 ohms
or more but less than 6.
6Ω: Select if the impedances of all speakers are
between 6 and 16 ohms.
f AUTO STANDBY switch
You can use the auto standby function. If the amplifier
receives no signal for 3 hours, it will automatically
enter standby mode. Once the auto standby function
has been activated, the amplifier will not
automatically turn on even if it receives the signal. To
turn on the amplifier, press the 8ON/STANDBY
button manually. You can also disable the function by
setting this switch to OFF side.
Default setting: ON (European models), OFF
(North American and Asian models)
Note
• Regardless of the position of this switch, this function will not
work when the amplifier has been turned on by the 12V trigger.
• Before entering standby mode by the auto standby function, the
amplifier notifies you by flashing the ON indicator for
10 seconds.
• Depending on some sources, the auto standby function may
activate during playback.
En
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting the Amplifier
Speaker Connection Precautions
Connecting Your Speakers
Read the following before connecting your speakers:
• You can connect speakers with an impedance of between
4 and 16 ohms. If the impedance of any of the connected
speakers is 4 ohms or more, but less than 6 ohms, be sure
to set the minimum speaker impedance to “4Ω”
impedance, and use the amplifier at high volume levels
for a long period of time, the built-in protection circuit
may be activated.
Before connecting the speakers, place them correctly by
consulting the instruction manuals that came with them.
For surround playback, the configuration and placement
of your speakers are very important.
Please note that connecting speakers with a low power
input rating does not produce large sound volumes. For
those speakers, large sound volumes causing excessive
input level may damage the speakers.
Note
• Disconnect the power cord from the wall outlet before
making any connections.
• Once you’ve completed speaker connections, you must turn
on the AV controller or control amplifier and configure the
output channels.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• If you use 4 or 5 speakers, connect each of the two
surround speakers to the SURROUND L/R terminals.
Do not connect them to the SURR BACK L/R or
FRONT HIGH/WIDE L/R terminals.
• Be careful not to short the positive and negative wires.
Doing so may damage the amplifier.
• Make sure the metal core of the wire does not have
contact with the amplifier’s rear panel. Doing so may
damage the amplifier.
Attaching the Speaker Labels
The amplifier’s positive (+) speaker terminals are all red
(the negative (–) speaker terminals are all black).
Speaker
Color
White
Red
Front left
Front right
Center
Green
Blue
Surround left
Surround right
Surround back left
Surround back right
Front high/wide left
Front high/wide right
Gray
Brown
Tan
White
Red
The supplied speaker cable labels are also color-coded and
you should attach them to the positive (+) side of each
speaker cable in accordance with the above table. Then all
you need to do is to match the color of each label to the
corresponding speaker terminal.
(North American models)
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the amplifier.
• Don’t connect one speaker to several terminals.
• If you are using banana plugs, tighten the speaker
terminal before inserting the banana plug.
• Do not insert the speaker code directly into the center
hole of the speaker terminal.
En
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Speaker Cables
Strip about 1/2" to 5/8" (12
Fully insert the bare wires.
Screw the terminal tight.
1/2" to 5/8"
(12 to 15 mm)
1
3
4
to 15 mm) of insulation from
the ends of the speaker
cables, and twist the bare
wires tightly, as shown.
Unscrew the terminal.
2
The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one
surround back speaker, connect it to the SURR BACK L terminal.
Note
• If you use front high or front wide speakers, you must turn on the AV controller and select the speakers to be used.
For more details, see the instruction manual of the connected component.
The amplifier
Select 4Ω or 6Ω.
Surround
right
Front right
Center
Front left
Surround
left
Front
high/wide
right
Surround
back right
Surround
back left
Front
high/wide
left
En
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an AV Controller with XLR output
Since many users will purchase the amplifier together with the Onkyo AV controller PR-SC5509, here is an explanation
of how to connect the amplifier to the PR-SC5509. For more details, see the instruction manual of the connected
component.
Note
• When using the balanced inputs, do not connect anything to the RCA inputs.
• Make sure that the balanced cable is not split. The split balanced cable may be the cause of noise.
• If a device with the USA type terminal is connected, the phase will be reversed. In this case, swap the polarity of the XLR connector in
order to set the polarity to the European type before connecting.
The amplifier
XLR type
Balanced cable
From the AV controller
AV controller
From the amplifier
En
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an AV Controller with RCA output
Since many users will purchase the amplifier together with the Onkyo AV controller PR-SC5509, here is an explanation
of how to connect the amplifier to the PR-SC5509. For more details, see the instruction manual of the connected
component.
Note
• When using the RCA inputs, do not connect anything to the balanced inputs.
• Make sure that the pin cable is not split. The split pin cable may be the cause of noise.
• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).
• To prevent interference, keep audio and video cables away from power cords and speaker cables.
The amplifier
Right!
Wrong!
AV controller
En
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-amping the Front Speakers
The FRONT L/R and FRONT HIGH/WIDE L/R outputs can be used with front speakers and front high/wide speakers
respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support
bi-amping, providing improved bass and treble performance.
Note
• Please make sure that your AV controller supports bi-amping.
• When bi-amping is used, the amplifier is able to feed up to 7-channel speakers in the main room.
• When bi-amping is used, front high/wide speakers cannot be used.
• For bi-amping, the FRONT L/R outputs feed the front speakers’ woofer terminals. And the FRONT HIGH/WIDE L/R outputs feed
the front speakers’ tweeter terminals.
• Once you’ve completed the bi-amping connections shown below, you must turn on the AV controller and configure it to enable
bi-amping. For more details, see the instruction manual of the connected component.
• You can also use unbalanced (RCA) connections for bi-amping.
Important:
• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter
(high) and woofer (low) terminals.
• Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual.
AV controller
The amplifier
Tweeter (high)
Woofer (low)
Front right
Front left
En
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Multiroom Connections
You can use three speaker systems with this amplifier—a surround-sound speaker system in your main listening
room, Zone 2: a stereo speaker system in a second room, Zone 3: a stereo speaker system in a third room. The following
examples are based on using the amplifier with the AV controller, PR-SC5509. For more details, see the instruction
manual of the connected component.
Note
• Please make sure that your AV controller has the multi-zone capability.
• Once you’ve completed multi-zone connections shown below, you must turn on the AV controller and configure it to enable the
multi-zone capability.
• If your AV controller has balanced outputs for multiroom versatility, you can also use the balanced inputs on the amplifier.
■ Connection 1
Main room: You can enjoy up to 5-channel surround-sound playback.
Zone 2: You can enjoy 2-channel stereo playback and video playback.
Zone 3: You can enjoy 2-channel stereo playback.
Zone 2
Zone 3
Make either
connection.
AV controller
Right
Left
Right
Left
The amplifier
Main room
Surround right
Front right
Center
Front left
Surround left
En
16
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Connection 2
Main room: You can enjoy up to 7-channel surround-sound playback.
Zone 2: You can enjoy 2-channel stereo playback and video playback.
Make either connection.
Zone 2
AV controller
Right
Left
The amplifier
the connection.
Main room
Surround back Surround right
right
Front right
Center
Front left
Surround left Surround back
left
En
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
If the PA-MC5501 fails to function normally, first check
the following points before contacting your Onkyo dealer.
If the problem is not solved after going through the
following list, unplug the power cord and contact your
Onkyo dealer.
■ The 12V trigger of the PA-MC5501 does not
react to that of the PR-SC5509
Connection between the 12V trigger terminals is incomplete.
→ Connect the cables to the terminals firmly.
■ Humming or other noise is heard
■ No power
Input cable connection is incomplete.
→ Insert the input cable to pin jack or connector completely.
Power cord is not correctly plugged into AC outlet/Inlet.
→ Plug the power cord into the AC outlet/Inlet properly.
Noise from power cord or power transformer affects the input
cable.
■ Power turns on but no sound
→ Keep power cord or power transformer away from the
Incomplete connections.
input cable.
→ Check speaker cable connections.
→ Insert all plugs firmly into jacks.
Power cord or speaker cables are bundled together with pin
cords.
No input signal from AV controller.
→ Check for input signal from AV controller.
→ This may cause humming or noise. Do not bundle power
cord or speaker cables with pin cables together.
Incorrect INPUT SELECT switch setting.
→ Set INPUT SELECT switch to correct setting.
Connection to the input terminals is not complete or not
appropriate.
→ For each channel’s input terminals, connect cables or cords
to either balanced input terminal or audio input terminal only
and switch the INPUT SELECT switch accordingly.
Avoid connecting the cables or cords to the input terminals
that will not be used.
■ The amplifier turns off and after restoring the
power, it turns off again
The protection circuit has been activated. Remove the power
cord from the wall outlet immediately. Make sure that all
speaker cables and input sources are properly connected, and
leave the amplifier with its power cord disconnected for 1
hour. After that, reconnect the power cord and turn the power
on. If the amplifier turns off again, unplug the power cord and
contact your Onkyo dealer.
WARNING
If smoke, smell or abnormal noise is produced by the
amplifier, unplug the power cord from the wall outlet
immediately and contact your Onkyo dealer.
En
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Amplifier section
General
Rated Output Power
Power Supply
(North American)
AC 120 V, 60 Hz
(Others)
All channels:
(North American)
150 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.05% (FTC)
AC 220 - 240 V, 50/60 Hz
Power Consumption (North American) 11.7 A
(Others) 1050 W
No-sound Power Consumption
175 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven at 1 kHz, with a maximum total
harmonic distortion of 0.7% (FTC)
185 watts minimum continuous power
per channel, 6 ohm loads, 2 channels
driven at 1 kHz, with a maximum total
harmonic distortion of 0.1% (FTC)
(North American) 80 W
(Others) 75 W
Stand-by Power Consumption
(North American) 0.2 W
(Others) 0.3 W
Dimensions (W × H × D)
(Others)
435 mm × 198.5 mm × 446.5 mm
17-1/8" × 7-13/16" × 17-9/16"
9 ch × 220 W at 6 ohms, 1 kHz, 1 ch driven
of 1 % (IEC)
Weight
22.2 kg (48.9 lbs.)
Maximum Effective Output Power
(Asian)
■ Audio Inputs
9 ch × 280 W at 6 ohms, 1 kHz, 1 ch driven
(JEITA)
Balance Inputs
9
9
*
Dynamic Power
Unbalance Inputs
*
IEC60268-Short-term maximum output power
400 W (3 Ω, Front)
300 W (4 Ω, Front)
180 W (8 Ω, Front)
■ Speaker Outputs
FL, FR, C, SL, SR, SBL, SBR, FHL/FWL, FHR/FWR
THD+N (Total Harmonic Distortion+Noise)
0.05 % (20 Hz - 20 kHz, half power)
60 (Front, 1 kHz, 8 Ω)
Input Sensitivity and Impedance
■ Control Terminal
Damping Factor
12 V Trigger In
1
1 V, 47 kΩ (Unbalanced)
2 V, 22 kΩ (Balanced)
Frequency Response 5 Hz - 100 kHz/+1 dB, -3 dB (Unbalanced)
Signal to Noise Ratio 110 dB (Unbalanced, IHF-A)
Speaker Impedance
4 Ω - 16 Ω
Specifications and features are subject to change
without notice.
En
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
Y1107-1
SN 29400874
(C) Copyright 2011 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
* 2 9 4 0 0 8 7 4 *
|