Integrated Amplifier
A-9000R
Instruction Manual
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
6. Batteries and Heat Exposure
IMPORTANT
Warning
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved
by ASTA or BSI to BS1362 and have the same ampere
rating as that indicated on the plug. Check for the ASTA
mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
For European Models
Declaration of Conformity
WARNING
We,
ONKYO EUROPE
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
• This unit’s top and rear panels may get warm after
prolonged use. This is normal.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do
not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
extended period, remove the power cord from the AC
outlet.
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
En
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
• 140 W/Ch (4 ohm, 20 Hz - 20 kHz, 0.05%,
2 Channels Driven, IEC)
• A WRAT (Advanced Wide Range Amplifier
Technology)
• PLL Ultra-Low Jitter Technology
• Separate Wolfson 192 kHz/24-Bit DACs
(WM8742) for L/R Channels
• Direct Mode
• DIDRC (Dynamic Intermodulation Distortion
Reduction Circuitry)
• Tone Control (Bass/Treble)
• Balance Control
• Quad Push-Pull Amplification Design with
Three-Stage Inverted Darlington Circuitry
• Symmetrical Layout of Power Stage
• Four Large 18,000 µF Capacitors
• Anti-Vibration Aluminum Panels for Front
and Sides
• Side-mounted Circuit Board Construction to
Reduce Vibration
• Separate Digital/Analog Circuitry
• Low-noise Static Display
• Independent Headphone Amplifier
• Discrete Phono Equalizer
• Phono Input (MM/MC)
*1
• De-emphasis Function
• USB Digital Input for 192 kHz/24-Bit HD
*2
Audio from PC
• AES/EBU Balanced Digital Input with XLR
Connector
• 4 Digital Inputs (1 AES/EBU, 2 Coaxial and 1
Optical)
• Gold-Plated, Machined Solid Brass RCA
Inputs
• Gold-Plated Large Speaker Posts
• Display Dimmer (Normal/Dim/Off)
*1
This function only applies to the following
sampling rates: 32 kHz, 44.1 kHz, 48 kHz. Other
rates are not supported.
*2
Playback of PC audio requires dedicated software
that can be downloaded from the Onkyo web site.
Audio signals of up to 32 bit can be input.
However, the resulting output will be equivalent
to a quality of 24 bit.
En
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Technologies
1. A WRAT (Advanced Wide Range
Amplifier Technology)
– Low Negative-Feedback Design
– HICC (High Instantaneous-Current
Capability)
Conventional amplifiers make extensive use of
negative feedback (NFB), whereby part of the
output signal is re-input in order to improve the
S/N ratio across a wide frequency range.
However, too much NFB makes a system
susceptible to counter-electromotive force from
the speakers, resulting in a drop in perceived
sound quality. To avoid this, Onkyo focuses on
improving the frequency response and reducing
distortion, without relying so much on NFB.
We use a low negative-feedback design
incorporating audiophile-grade, close-tolerance
components, to achieve a frequency response,
out to 100 kHz.
The A-9000R employs a host of proprietary
Onkyo technologies to ensure optimal audio
performance.
When an amplifier outputs an audio signal, the
connected speakers accumulate energy, reflex,
and send energy back to the amplifier. The
amplifier must then immediately cancel the
speakers’ reflex energy and instantaneously
send out the next signal. The same high current
required to achieve this is also necessary to
handle speaker impedance, fluctuations, which
can force an amplifier to provide four to six
times its usual current load. The A-9000R’s
instantaneous current capability ensures that
audio output is not affected by power
– DIDRC (Dynamic Intermodulation
Distortion Reduction Circuitry)
Since the advent of digital audio, the values of
S/N (signal-to-noise) ratio have risen
significantly. However, it is also recognized that
in terms of perceived S/N, analog audio sources
are not inferior to digital sources.
Generally, S/N measures the ratio when sound
is and not produced, but takes no account of the
noise generated during sound reproduction.
For a long time, Onkyo has focused and made
extensive research on the S/N when sound is
produced (dynamic S/N). Using a mechanism
that captures the noise beyond audible range, it
has been possible to determine that both
dynamic S/N and perceived S/N aggravate
during music reproduction.
Although frequencies above 20 kHz are beyond
human hearing, it is well known that a beat can
be perceived if different signals are overlapped
at such frequencies.
During the analog audio era, no significant
signals were entering beyond the audible range.
However, the digital era has made recording
beyond the audible range possible and the
generated beat is now perceivable.
limitations.
– Closed Ground-Loop Circuits
– Symmetrical Twin-Monaural
Construction
If an amplifier’s ground potential (voltage)
fluctuates during playback, noise is likely to
result. In an open-loop circuit design, where all
circuits wire connected to the power supply via
a single loop (as on many amplifiers), the noise
is compounded. To avoid this, the A-9000R
employs a sophisticated closed-circuit design in
which each circuit has a separate link to the
power supply. This helps to cancel individual
circuit noise and keep the ground potential free
of distortion.
Power devices for the left and right channels of
the A-9000R are aligned symmetrically. Each
channel has the same electrical and structural
design, and signal pathways are uniform in
length. This helps to minimize errors in
stereophonic playback.
With Onkyo’s DIDRC technology, a new
approach is introduced which prevents such
beat from penetrating the audible range.
En
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Quad Push-Pull Amplification Design
with Three-Stage Inverted Darlington
Circuitry
4. Side-mounted Circuit Board
Construction
Rather than being directly connected to the
chassis base, the circuit boards inside the
A-9000R are cushioned by internal struts and
affixed to the front, side, and rear panels. This
method of construction prevents vibrations
from the chassis from adversely affecting the
circuit boards.
Three-Stage Inverted Darlington Circuitry
brings greater efficiency to the A-9000R
integrated amp by employing a low-NFB
design to maintain voltage stability and
enhance transient response. Extremely sensitive
to oscillations, this circuitry requires very
advanced control technology in order to be
incorporated into the amplifier. Breaking
further new ground, the A-9000R employs two
extra transistors for each channel in a “quad
push-pull” design that significantly enhances
amplification power.
5. Playback of Various Music Sources
Including PC Audio via USB
Using the USB port on the rear panel of the
A-9000R, you can connect your PC and play
back 192 kHz/24-bit HD audio formats .
*
*
Playback of PC audio requires dedicated software
3. PLL (Phase Locked Loop) Ultra-Low
Jitter Technology
that can be downloaded from the Onkyo web site.
Audio signals of up to 32 bit can be input.
However, the resulting output will be equivalent to
a quality of 24 bit.
Jitter is an unwanted side-effect of the digital-
to-analog conversion process caused by
fluctuations in the time domain of a digital
signal. PLL ultra-low jitter technology reduces
jitter by comparing the input and output phases
of the digital signal and creating an accurate
clock waveform. This enhances the precision of
digital signal processing and noticeably
improves perceived audio quality.
En
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Block Diagram
DIDRC
(Dynamic Intermodulation Distortion Reduction Circuitry)
Quad Push-pull, 3-Stage Inverted Darlington Circuitry
1st Amp
2nd Amp
MAIN IN
SPEAKERS A
SPEAKERS B
NFB
Mute
Analog +15V
DAC +12V
PRE OUT
Discrete Phono
Equalizer
Power Amp
Analog -15V
DAC -12V
PHONO
Volume Min
0dB
VOLUME
Input Selector Buffer Amp
Buffer Amp
LINE 1
LINE 2
LINE 3
14dB Amp
Control 1
1dB
Volume Max
Tone
Control
Volume Balance
L ch +
Buffer Amp
HEADPHONES
Mute
LINE OUT
L ch -
Buffer Amp
Head Phone Volume
R ch +
DAC
DAC
OPTICAL
COAXIAL 1
COAXIAL 2
AES/EBU
(WM8742)
Differential
Operation
(WM8742)
Differential
Operation
Buffer Amp
Buffer Amp
Buffer Amp
R ch -
FL
Jitter Cleaner
DIR
FL
USB
Controller
Control 2
USB IN
RI CONTROL
u
En
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Make sure you have the following accessories:
Remote controller and two batteries
Remote controller (RC-829S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)
Batteries (R03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2)
Power cord
Power cord (1.8 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)
(Plug type varies from country to country.)
*
In catalogs and on packaging, the letter at the end of the product name indicates the color.
Specifications and operations are the same regardless of color.
Thank you for purchasing an Onkyo Integrated Amplifier. Please read this manual
thoroughly before making connections and plugging in the unit.
Following the instructions in this manual will enable you to obtain optimum
performance and listening enjoyment from your new Integrated Amplifier.
Please retain this manual for future reference.
En
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction
Advanced Operations
Important Safety Instructions .................................................................................2
Custom Setup.........................................................................................................36
Changing Input Names......................................................................................36
Skipping Unused Inputs.....................................................................................37
Setting the Headphone Level ............................................................................37
Setting the Auto Standby Function....................................................................38
Setting the Route...............................................................................................39
Restoring the Default Settings...........................................................................40
Precautions...............................................................................................................3
Features ....................................................................................................................4
Technologies............................................................................................................5
Block Diagram..........................................................................................................7
Supplied Accessories..............................................................................................8
Before Using the Integrated Amplifier .................................................................10
Installing the Batteries .......................................................................................10
Using the Remote Controller .............................................................................10
Installing the Integrated Amplifier ......................................................................10
Getting to Know the Integrated Amplifier ............................................................11
Front Panel ........................................................................................................11
Rear Panel.........................................................................................................13
Remote Controller..............................................................................................14
Others
Troubleshooting.....................................................................................................41
Specifications.........................................................................................................43
Connections
Connections ...........................................................................................................15
Connecting Your Speakers................................................................................15
Cable and Jacks ................................................................................................17
Connecting the Power Cord...............................................................................18
Connecting a CD Player ....................................................................................19
Connecting an Onkyo Dock...............................................................................20
Connecting a Tuner ...........................................................................................21
Connecting Onkyo u Components..................................................................22
Connecting a Turntable .....................................................................................23
Connecting a Cassette Tape Deck....................................................................23
Connecting a Recording Component.................................................................24
Using the Integrated Amplifier as a Preamplifier ...............................................25
Separating the Pre-amp and Main Amp Units ...................................................26
Using the Integrated Amplifier as a Power Amplifier..........................................27
Basic Operations....................................................................................................28
Turning On/Off the Integrated Amplifier.............................................................28
Selecting Speakers A and Speakers B..............................................................29
Adjusting the Volume.........................................................................................29
Selecting the Input Source.................................................................................29
Adjusting the Display Brightness .......................................................................30
Using the Direct Function ..................................................................................30
Adjusting the Bass, Treble and Balance............................................................31
Muting the Sound...............................................................................................31
Changing the Display Information......................................................................32
Using Headphones ............................................................................................32
Controlling Other Onkyo Components ................................................................33
Controlling the Onkyo CD Player.......................................................................33
Controlling the Onkyo Dock...............................................................................33
Controlling the Onkyo Network Tuner................................................................34
Using the Integrated Amplifier as a USB Audio Device .....................................35
Connecting a PC................................................................................................35
Installing USB drivers ........................................................................................35
Playing Music Files from the PC........................................................................35
En
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using the Integrated Amplifier
Installing the Batteries
Using the Remote Controller
Installing the Integrated Amplifier
To use the remote controller, point it at the integrated
amplifier’s remote control sensor, as shown below.
To open the battery compartment, press the small
hollow and slide the cover.
1
Remote control sensor
Integrated amplifier
Ensure proper ventilation.
30 cm
Approx. 5 m
Insert the two supplied batteries (R03) in
accordance with the polarity diagram inside the
battery compartment.
10 cm
2
10 cm
Note
• The remote controller may not work reliably if the integrated
amplifier is subjected to bright light, such as direct sunlight or
inverter-type fluorescent lights. Keep this in mind when
installing.
10 cm
Install the integrated amplifier on a sturdy rack or shelf.
Position it so that its weight is evenly dispersed on its four
legs. Do not install the integrated amplifier in a place with
vibration or an unstable location.
The integrated amplifier is designed to have high
conversion efficiency, however, its temperature will
become much higher than other audio equipment.
Therefore, make sure not to hamper heat dissipation by
ensuring proper ventilation.
• If another remote controller of the same type is used in the same
room, or the integrated amplifier is installed close to equipment
that uses infrared rays, the remote controller may not work
reliably.
Replace the cover and slide it shut.
• Don’t put anything, such as a book, on the remote controller,
because the buttons may be pressed inadvertently, thereby
draining the batteries.
3
• The remote controller may not work reliably if the integrated
amplifier is installed in a rack behind colored glass doors. Keep
this in mind when installing.
• The remote controller will not work if there’s an obstacle
between it and the integrated amplifier’s remote control sensor.
Note
• If the remote controller doesn’t work reliably, try replacing the
batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
En
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the Integrated Amplifier
Front Panel
a
b
c
d
e f g
h
j
i
For detailed information, see the pages in parentheses.
a 8ON/STANDBY button (➔ page 28)
f DIRECT LED (➔ page 30)
j Front flap
Sets the integrated amplifier to On or Standby.
Lights when the integrated amplifier is in Direct
mode.
Gently push on the lower end of the front panel to
open the flap.
b Remote control sensor (➔ page 10)
g Display Off LED (➔ page 30)
Receives control signals from the remote controller.
Lights when the information display is turned off.
c MAIN IN LED (➔ page 27)
h Information display
Lights when the integrated amplifier is used as a
power amplifier (Main mode).
Displays various information.
d Volume controller (➔ page 29)
i INPUT selector (➔ pages 29, 35)
Selects the input sources in sequence. It is also used to
select settings.
Adjusts the volume.
e DIRECT switch (➔ page 30)
Enables or disables the Direct function.
En
11
Download from Www.Somanuals.com. All Manuals Search And Download.
k
l
m
n
o
p
q
For detailed information, see the pages in parentheses.
k POWER switch (➔ page 28)
n TREBLE -/+ buttons (➔ page 31)
This is the main power switch. When set to the OFF
position (@), the integrated amplifier is completely
shut down. It must be switched to the ON position
(^) to set the integrated amplifier to On or Standby.
Adjusts the level of treble sounds. Press the button
once to display the current level value.
Adjusts the balance of left and right channels.
l SPEAKERS button and A/B LEDs (➔ page 29)
Selects Speakers A, Speakers B, or both. The A and B
LEDs show which speaker set is selected.
p SETUP button (➔ page 36)
Selects and confirms settings.
q PHONES jack (➔ page 32)
m BASS -/+ buttons (➔ page 31)
Adjusts the level of bass sounds. Press the button once
to display the current level value.
En
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
d
a
b c
e f
g
h i
j
k
l
m
n
o
a SPEAKERS A terminals
f DIGITAL IN OPTICAL jack
m PRE OUT L/R jacks
Connect Speakers A.
Connects components such as CD players with optical
digital audio output.
Connect a power amplifier when the integrated
amplifier is used as a preamplifier (Pre mode).
b u REMOTE CONTROL jacks
g SPEAKERS B terminals
n MAIN IN L/R jacks
Connect Onkyo components such as Onkyo Docks,
CD Players, or Network Tuner with u (Remote
Interactive) jacks.
Connect Speakers B.
Connect a preamplifier when the integrated amplifier
is used as a power amplifier (Main mode).
h PHONO (MM/MC) L/R jacks
o AC INLET
Connect a turntable with analog audio output.
c USB port
Connects the supplied power cord. The other end of
the power cord should be connected to a suitable wall
outlet.
Connects a PC. The music files of your PC are played
through the integrated amplifier.
i MM/MC selector
Set this selector according to the turntable’s cartridge
format ( MM/ MC).
d DIGITAL IN AES/EBU jack
Connects components such as CD players with
balanced AES/EBU output.
j GND screw
See “Connections” for connection information
(➔ pages 15 to 27).
Connects the turntable’s ground wire.
k LINE IN 1/2/3 L/R jacks
Note
Connect playback devices with analog audio output.
• Be careful not to connect components with analog
XLR output.
l LINE OUT L/R jacks
Connect components such as analog line-level
sources. The input signals are output with no level
adjustment.
e DIGITAL IN COAXIAL 1/2 jacks
Connect components such as CD players with coaxial
digital audio output.
En
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
For detailed information, see the pages in parentheses.
You can also use the remote controller to control your
Onkyo CD Player (e.g. C-7000R), Onkyo Dock, or Onkyo
Network Tuner (e.g. T-4070).
a 8 button (➔ page 28)
aa
d
Sets the integrated amplifier to On or Standby.
b DIMMER button (➔ page 30)
bb
g
Adjusts the display brightness.
Note
c !/"/#/$ and ENTER buttons
• Make sure the remote controller is pointed at the CD player
when using it.
Select and adjust settings.
d VOLUME q/w buttons (➔ page 29)
• With some components, the remote controller may not work, or
only partially.
Adjust the volume of the integrated amplifier.
• To control the Onkyo Dock and Onkyo Network Tuner, an u
e INPUT!/" buttons (➔ page 29)
connection is required (➔ page 22).
Select an input source.
• Refer to the manuals supplied with your Onkyo CD Players,
Network Tuner or RI Docks.
f SETUP button (➔ page 36)
e
f
Enters the Setup menu.
g DISPLAY button (➔ page 32)
■ Controlling the Onkyo CD player (➔ page 33)
d 8 CD button
Displays the current input and settings.
h RETURN button
e Playback mode buttons
Returns to the previous display when changing
settings.
■ Controlling the Onkyo Dock (➔ page 33)
a 8 button
cc
i MUTING button (➔ page 31)
Mutes or unmutes the integrated amplifier.
b DIMMER button
d
j TONE/BAL button (➔ page 31)
Adjusts the tone (bass/treble) and balance of the
integrated amplifier.
f !/" and ENTER buttons
g Dock control buttons
h
e
f
■ Controlling the Onkyo Network Tuner
(➔ page 34)
i
j
a 8 button
b DIMMER button
c !/"/#/$ and ENTER buttons
gh Tuner control buttons
g
h
En
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connections
Connecting Your Speakers
Note
Right
Left
• Make sure that the wires do not touch metal parts on the back panel or elsewhere.
• Y plugs cannot be connected.
Speakers A
• Two sets of speakers (Speakers A and Speakers B) can be connected to the integrated amplifier. You can
select which speakers to output audio to when listening to music.
You can also output audio from both sets of speakers.
• If you use Speakers A or Speakers B, make sure to use speakers with an impedance of 4 to 16 ohms. If
you use Speakers A and Speakers B, make sure to use speakers with an impedance of 8 to 16 ohms.
Connecting speakers with an impedance less than 8 ohms may cause the protection circuit to activate.
• Don’t connect more than one speaker wire to a single speaker terminal. Doing so could damage the
integrated amplifier or cause it to malfunction.
Integrated Amplifier
A-9000R
• When using only one speaker, or when playing back monaural audio, don’t connect a single speaker to
both the left and right speaker terminals.
• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to
positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the
wrong way around, the sound will be out of phase and will feel unnatural.
• Be careful not to short the positive and negative wires. Doing so may damage the integrated amplifier.
• Make sure the metal core of the wire does not have contact with the integrated amplifier’s rear panel.
Doing so may damage the integrated amplifier.
Speakers B
Right
Left
Strip 15 to 20 mm of insulation from the ends of the speaker cables, and twist the bare wires
tightly, as shown.
15 to 20 mm
En
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-wiring Connection
Bi-wiring provides improved bass and treble performance. Using terminals of both SPEAKERS A and SPEAKERS B, it separates high frequency from low frequency signals.
Important:
• Bi-wiring can be used only with speakers that support bi-wiring. Refer to your speaker manual.
• When making the bi-wiring connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.
• When making the bi-wiring connections, set SPEAKERS to A+B (➔ page 29).
Integrated Amplifier A-9000R
Tweeter (high)
Woofer (low)
Right speaker
Left speaker
Tip
• As shown on the illustration, the wiring terminals of SPEAKERS A are connected to the woofer and SPEAKERS B are connected to the tweeter. However, wiring them the other way around is also possible.
En
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable and Jacks
Balanced AES/EBU
This is a professional digital audio interface. Balanced AES/EBU cables are used for better noise immunity and longer cable runs. The maximum
sampling rate for PCM input is 192 kHz/24 bit, 2ch. The integrated amplifier provides 110-ohm impedance matching.
USB digital audio
USB digital connections allow you to enjoy digital sound. The integrated amplifier supports high-speed USB 2.0. Use Type A-B USB cable. The
maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch.
USB
Optical digital audio
Optical digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 96 kHz/24 bit, 2ch.
OPTICAL
Coaxial digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch.
The integrated amplifier provides 75-ohm impedance matching.
*
Coaxial digital audio
Orange
Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.
L
White
Red
R
u
To use u (Remote Interactive), you need to connect your Onkyo CD Player, Network Tuner, or RI Dock to the integrated amplifier with an u
cable.
Note
• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).
• To prevent interference, keep audio cables away from power cords and speaker cables.
Right!
• The integrated amplifier’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.
• To prevent shutter damage, hold the optical plug straight when inserting and removing.
• Do not use digital audio signals other than PCM.
Wrong!
*
An analog audio cable can be used instead of a coaxial cable. However, we recommend that you use a coaxial or a composite video cable.
About Balanced Input (AES/EBU Jack)
Plugging the AES/EBU cable
Unplugging the AES/EBU cable
Match the pins and insert the terminal until you hear a “click”. Make sure that the terminal is
locked by lightly pulling the connection cable.
Pull out the connection cable while holding down the lever.
a
Push
b
En
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cord
Integrated Amplifier A-9000R
Supplied power cord
To an AC wall outlet
(Plug type varies from country to country.)
Connect all of your speakers and components.
1
Tip
Note
• Never disconnect the power cord from the integrated
amplifier while the other end is still plugged into a wall
outlet. Doing so may cause an electric shock. Always disconnect
the power cord from the wall outlet first, and then the integrated
amplifier.
• To reduce noise, do not tie signal cables together with the power
cable. Wire them so that they are away from each other.
• Depending on the country, the integrated amplifier may be
polarity-sensitive. In this case, plug the power cord in a way that
provides the best sound quality.
Connect the supplied power cord to the integrated
amplifier’s AC INLET.
2
3
Plug the power cord into an AC wall outlet.
• Turning on the integrated amplifier may cause a momentary
power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the integrated
amplifier into a different branch circuit.
• Do not use a power cord other than the one supplied with the
integrated amplifier. The supplied power cord is designed
exclusively for use with the integrated amplifier and should not
be used with any other equipment.
En
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a CD Player
This is an example of connection using the CD Player C-7000R.
Analog Connection
Digital Connection (Coaxial or Optical)
Integrated Amplifier A-9000R
Integrated Amplifier A-9000R
Connect either of them.
CD Player C-7000R
CD Player C-7000R
Tip
Tip
• Connect the CD Player to either of the following jacks: COAXIAL1/2, OPTICAL.
• Connect the CD Player to either of the following jacks: LINE IN 1/2/3.
En
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an Onkyo Dock
This is an example of connection using the Onkyo Digital Media Transport.
Digital Connection (AES/EBU)
Integrated Amplifier A-9000R
Integrated Amplifier A-9000R
Connect either of them.
CD Player C-7000R
OPTICAL
COAXIAL
N
/S
T
A
N
D
B
Y
S
T
A
N
D
B
Y
iP
o
d
P
C
U
S
Y
N
N
C
S
Y
/
N
C
Digital Media Transport
Note
• Use only an Onkyo Dock with digital connections.
• To use the u (Remote Interactive) connection, you need to change the names of inputs
(➔ pages 22, 36).
Tip
• Connect the Onkyo Dock to either of the following jacks: COAXIAL1/2, OPTICAL.
En
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Tuner
This is an example of connection using the Network Tuner T-4070.
Analog Connection
Digital Connection (AES/EBU, Coaxial or Optical)
Integrated Amplifier A-9000R
Integrated Amplifier A-9000R
Connect either of them.
Network Tuner T-4070
Network Tuner T-4070
Note
Note
• To use the u (Remote Interactive) connection, you need to change the names of inputs
(➔ pages 22, 36).
(➔ pages 22, 36).
Tip
Tip
• Connect your tuner to either of the following jacks: LINE IN 1/2/3.
• Connect the Network Tuner to either of the following jacks: AES/EBU, COAXIAL1/2, OPTICAL.
En
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Onkyo u Components
With u (Remote Interactive), you can use the following special functions:
Integrated Amplifier A-9000R
■ Auto Power On
When you start playback on a component connected via u while the integrated amplifier
is on Standby, the integrated amplifier will automatically turn on and select that component
as the input source.
■ Direct Change
When playback is started on a component connected via u, the integrated amplifier
automatically selects that component as the input source.
■ System Off
When you turn off the integrated amplifier, the components turn off automatically.
■ Remote Control
You can use the integrated amplifier’s remote controller to control your other u-capable
Onkyo Network Tuner or RI Dock, pointing the remote controller at the integrated
amplifier’s remote control sensor instead of the component.
Tip
• For details on operating the connected components, see “Controlling Other Onkyo Components”
O
N
/S
T
A
N
D
B
Y
S
T
A
N
D
B
Y
(➔ page 33).
iP
o
d
P
C
U
S
Y
N
N
C
S
Y
/
N
C
Note
RI Dock
• Use only u cables for u connections. u cables are supplied with your Onkyo CD Player, Network
Tuner or RI Dock.
Network Tuner or CD Player
• If two u jacks are present, you can use either one indifferently as they work the same way.
• Connect only an Onkyo CD Player, Network Tuner or RI Dock to the u jacks. Connecting other
manufacturer’s components may cause a malfunction.
Change the names of inputs in accordance with each component connected
(➔ page 36).
1
• Only Onkyo CD Players (e.g. C-7070), Network Tuners (e.g. T-4070), and RI Docks (e.g. ND-S1000)
are supported by the integrated amplifier’s u. With other components such as MD recorders, the u
won’t work properly.
Connected component
CD Player
Names of inputs
CD
• Some components may not support all u functions. Refer to the manuals supplied with your Onkyo
CD Players, Network Tuner or RI Docks.
Network Tuner
RI Dock
TUNER
• The CD Players only support the Auto Power On and Direct Change functions.
DOCK
Make sure that each Onkyo CD Player, Network Tuner or RI Dock is connected
(➔ pages 19 to 21).
2
3
Make the u connections (see the illustration).
En
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Turntable
Connecting a Cassette Tape Deck
Integrated Amplifier A-9000R
Integrated Amplifier A-9000R
MM/MC selector
L
R
AUDIO
OUTPUT
L
R
AUDIO
OUT
Cassette tape deck
Turntable without a built-in
phono preamp
Tip
Use the MM/MC selector on the back of the integrated amplifier to select either MM or MC,
in accordance with the cartridge format of the turntable.
Remove the short pins plugged into the jacks before connecting a turntable to the PHONO
inputs.
• Connect your cassette tape deck to either of the following jacks: LINE IN 1/2/3.
Note
• Always turn off the integrated amplifier before switching between MM and MC.
Tip
• If your turntable has a built-in phono preamp, you can connect the turntable to other analog inputs such
as LINE IN 1.
• If your turntable has a ground wire, connect it to the GND screw. With some turntables, connecting the
ground wire may produce an audible hum. If this happens, disconnect it.
En
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Recording Component
Important:
• Unless you have the full consent of the copyright holder, copyright laws prohibit using your recordings
for anything other than personal enjoyment!
• Do not change the integrated amplifier’s input while recording. Doing so will cause the audio from the
selected component to be recorded.
Note
• Volume adjustments and use of the muting function are not reflected in the signal output from LINE
OUT.
• Manual tone adjustments using BASS -/+, TREBLE -/+, BALANCE L/R, and TONE/BAL are not
reflected in the signal output from LINE OUT.
• See the manual of the recording component for instructions on correct use.
Integrated Amplifier A-9000R
L
R
AUDIO
IN
Cassette tape deck
En
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Integrated Amplifier as a Preamplifier
The integrated amplifier can be used as a preamplifier (Pre mode). This mode keeps the heat down, as opposed to when the integrated amplifier is used as a pre-main amplifier. This is an example of
connection using the power amplifier M-5000R.
Important:
• In this mode, SPEAKERS cannot be used.
• To use this mode, you need to change the “ROUTE” setting (➔ page 39).
Integrated Amplifier A-9000R
Power Amplifier M-5000R
En
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Separating the Pre-amp and Main Amp Units
You can use the integrated amplifier’s pre-amp and main amp units individually (Split mode) to connect a sound processor such as a graphic equalizer between the pre-amp and main amp units.
Important:
• Always turn the integrated amplifier off before connecting the MAIN IN jacks.
• To use this mode, you need to change the “ROUTE” setting (➔ page 39).
Integrated Amplifier A-9000R
L
R
L
R
OUTPUT
INPUT
e.g., graphic equalizer
Note
• Depending on the sound processor used, noise may be produced upon switching the integrated amplifier on and off. In this case, turn on each device in the following sequence: sound processor, integrated amplifier. Turn off
each device in the following sequence: integrated amplifier, sound processor.
En
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Integrated Amplifier as a Power Amplifier
Combined with a preamplifier of your choice, the integrated amplifier can be used as a power amplifier (Main mode). When it is selected, the MAIN IN LED lights. See “Connecting Your Speakers”
for connection information (➔ page 15). This is an example of connection using the preamplifier P-3000R.
Important:
• Always turn the integrated amplifier off before connecting the MAIN IN jacks.
• Before setting the integrated amplifier to Main mode, make sure that no component such as a CD player is connected to the MAIN IN jacks, as a direct connection may cause a massive blast sound and damage the integrated
amplifier or your speakers.
• This mode can be used with the following limitations:
– The volume level can’t be adjusted.
– Only SPEAKERS and SETUP can be used.
– Only the MAIN IN and SPEAKERS terminals can be used.
– The Auto Standby function is not available (➔ page 38).
• To use this mode, you need to change the “ROUTE” setting (➔ page 39).
Preamplifier P-3000R
Integrated Amplifier A-9000R
En
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On
&
Basic Operations
Basic Operations
Turning On/Off the Integrated Amplifier
Turning On the Integrated Amplifier
Turning Off the Integrated Amplifier
8ON/STANDBY
■ Operating with the remote controller
■ Operating with the remote controller
Set %POWER to the ON position (^) on the
Press 8.
1
1
integrated amplifier.
The integrated amplifier enters Standby mode and the
information display goes off.
Press 8.
2
To completely shut down the integrated amplifier,
The integrated amplifier comes on, and the
information display lights.
2
set %POWER to the OFF position (@) on the
integrated amplifier.
■ Operating on the integrated amplifier
■ Operating on the integrated amplifier
Set %POWER to the ON position (^).
1
%POWER
Press 8ON/STANDBY.
1
The integrated amplifier enters Standby mode and the
information display goes off.
Press 8ON/STANDBY.
2
The integrated amplifier comes on, and the
information display lights.
To completely shut down the integrated amplifier,
2
8
set %POWER to the OFF position (@).
Tip
• After showing the volume level from the last session, the
message “MUTING” flashes on the information display until
the speakers or headphones become active.
Tip
• For details on power management settings, see “Setting the Auto
Standby Function” (➔ page 38).
• After a certain time of warming up, the internal temperature of
the integrated amplifier stabilizes, and the sound is softened.
• The integrated amplifier remembers the state when power was
last turned off, and returns to that state.
En
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Speakers A and Speakers B
Adjusting the Volume
Selecting the Input Source
You can select to output sound from Speakers A,
Speakers B, or both A + B.
You can adjust the volume within the following range:
VOLMIN, -95dB, -90dB, -85dB, -80dB to 14dB,
VOLMAX
You can switch inputs to select the desired source
component. Choose an input from the following:
LINE1, LINE2, LINE3, COAX1, COAX2, OPT,
AES-EBU, USB, PHONO
■ Operating with the remote controller
■ Operating with the remote controller
VOLUME q/w
INPUT !/"
Press INPUT!/" repeatedly.
1
SPEAKERS A B
Press VOLUME q/w repeatedly.
1
■ Operating on the integrated amplifier
INPUT selector
■ Operating on the integrated amplifier
Press SPEAKERS repeatedly on the integrated
1
amplifier.
The LED of the selected speakers lights.
Volume controller
Note
• While headphones are connected, this setting is disabled.
• When “ROUTE” is set to “PRE”, this setting is disabled
(➔ page 39).
• When this setting is set to A + B, the impedance of speakers is
restricted. For further details, see “Connecting Your Speakers”
(➔ page 15).
Use the INPUT selector.
1
Tip
• For changing the input’s name, see “Changing Input Names”
(➔ page 36).
• To hide the display of unused inputs, see “Skipping Unused
Inputs” (➔ page 37).
Use the volume controller.
1
Note
• If there is no USB connection, “USB” is not displayed.
Tip
• The default level is -55 dB.
En
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Display Brightness
Using the Direct Function
You can adjust the brightness of the integrated amplifier’s
information display.
By bypassing the tone control circuit, the Direct function
uses the shortest path for enhanced sound quality.
Although this function generally turns the display off, the
integrated amplifier makes use of a display that doesn’t
affect the sound quality. It is therefore possible to turn the
display on while the Direct function is enabled. Also,
since the left/right balance setting uses a system that
doesn’t affect the sound quality, the balance can be
adjusted even if the Direct function is enabled.
Press DIMMER repeatedly.
1
Normal → Dim → Off
Display Off LED
Normal
Dim
DIRECT switch
DIRECT LED
Off
The Display Off LED lights.
Note
• While the information display is turned off, pressing the buttons
used for settings and adjustments on the remote controller or
integrated amplifier will briefly activate the display in Dim
mode.
DIMMER
Set the DIRECT switch to the ON position.
The information display goes off and the DIRECT
LED lights.
1
Tip
• To turn the information display on while the Direct function is
enabled, press DIMMER on the remote controller.
En
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Bass, Treble and Balance
Muting the Sound
You can adjust the bass, treble and left/right output
balance respectively.
■ Operating on the integrated amplifier
You can temporarily mute the output of the integrated
amplifier.
■ Operating with the remote controller
#/$
MUTING
RETURN
TONE/BAL
BASS -/+
TREBLE -/+ BALANCE L/R
Press TONE/BAL repeatedly.
`BASS:
1
Press MUTING.
The message “MUTING” flashes on the information
display.
1
`TRBL (Treble):
You can adjust the bass and treble levels from -6
to +6.
Press BASS -/+, TREBLE -/+, or BALANCE L/R
repeatedly.
1
To unmute the integrated amplifier, press MUTING
again.
The adjustment is automatically confirmed.
Tip
• By default, bass and treble are set to 0, and balance is set to the
center position (no visible bars).
Note
`L, R (Balance):
Note
• While the integrated amplifier is muted:
The left and right output balance can be adjusted.
The more the bars move to the right, the higher
the volume will be on the right output.
Conversely, the more the bars move to the left,
the higher the volume will be on the left output.
When no bar appears on the display, the volume
is evenly distributed.
• The integrated amplifier will end the adjustment if there is no
operation for 5 seconds.
– Adjusting the volume or setting the integrated amplifier to
Standby will unmute the integrated amplifier.
• While the Direct function is enabled, the tone controls are
disabled and pressing the buttons will display the message
“DIRECT”.
• When headphones are connected, the balance can’t be adjusted
and pressing the buttons will display the message “PHONES”.
– Pressing INPUT!/" on the remote controller or turning the
INPUT selector on the integrated amplifier will display the
current input for 3 seconds.
• If MUTING is pressed while a setting is being performed, the
setup will be terminated.
• Even if the power is turned off or the power cord is unplugged,
the muting function will be maintained on to the next session.
Press #/$ repeatedly.
2
The adjustment is automatically confirmed.
To exit the adjustment, press RETURN.
En
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Display Information
Using Headphones
You can display information such as the current input or
the value of settings.
PHONES jack
Setting of ROUTE
To exit the adjustment, press RETURN.
DISPLAY
Note
• Input fs (sampling rate) is displayed only when a digital input
(COAX1, COAX2, OPT, AES-EBU, USB) is selected.
• Depending on the source, the value on the information display
may differ from the actual sampling rate’s.
Press DISPLAY repeatedly.
1
• When the Direct function is enabled, “BASS” and “TRBL” are
not displayed.
Current Input
• When a signal treated for treble emphasis (pre-emphasis) is
detected, the integrated amplifier is designed to restore the
original signal characteristics via the “de-emphasis” process.
The message “EMPHAS” only appears when a signal processed
with pre-emphasis is detected.
Connect a pair of stereo headphones with a
1
Current Volume
BASS Level
standard plug (6.3 mm) to the PHONES jack.
When connecting the headphones, the message
“PHONES” appears on the information display and
the A/B LEDs go off.
• When “ROUTE” is set to “MAIN”, DISPLAY can’t be used
(➔ page 39).
Tip
• When a variation of sampling rate is detected, the value is
automatically displayed.
You can adjust the volume and mute the sound, by
using VOLUME q/w.
TRBL (Treble) Level
While headphones are connected, no sound is output
from the speakers and PRE OUT jacks.
Input fs (sampling rate)
Tip
• If there’s a volume difference between your speakers and your
headphones, you can adjust the offset level (➔ page 37).
Note
Pre-emphasis Signal Detection
• Always turn down the volume before connecting your
headphones.
• When headphones are connected, the balance adjustment and
SPEAKERS are disabled. Pressing the buttons will display the
message “PHONES”.
En
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Onkyo Components
Controlling the Onkyo CD Player
Controlling the Onkyo Dock
You can use the integrated amplifier’s remote controller to
control your Onkyo CD player, pointing the remote
controller at the CD player’s remote control sensor.
Connect an Onkyo Dock to the integrated amplifier, and
play music files from your iPod.
You can use the integrated amplifier’s remote controller to
control basic iPod functions, but the functionality will
depend on your iPod model and generation.
8 button
Sets an Onkyo Dock to Standby.
DIMMER button
Adjusts the display brightness.
!/" and ENTER buttons
Select a music file.
Note
8CD
• With some components, the
remote controller may not
work, or only partially.
To control the Onkyo Dock, an u connection is
required (➔ page 22).
SHUFFLE button
Performs shuffle playback.
MENU button
Opens iPod menu or returns to the previous menu.
REPEAT button
To control the Onkyo Dock with the integrated
amplifier’s remote controller, you need to change the
input name to “DOCK” (➔ page 36).
Cycles through the repeat back modes.
Playback
mode buttons
7 button
8
Selects the beginning of the current song. Pressing this
button twice selects the previous song.
DIMMER
8 CD button
1/3 button
Sets the CD Player to On or Standby.
RANDOM button
Performs random playback.
Starts or pauses playback.
6 button
Selects the next song.
3 button
Pauses playback.
Tip
REPEAT button
• If you use your iPod with any other accessories, iPod playback
detection may not work.
Cycles through the repeat back modes.
• Use the integrated amplifier’s volume control to adjust the
playback volume.
7 button
!/"
Selects the beginning of the current song. Pressing this
button twice selects the previous song.
• While your iPod is inserted in an Onkyo Dock, its volume
control has no effect.
ENTER
1 button
Starts playback.
Note
6 button
• When the Auto Standby function is activated, the power of the
Onkyo Dock connected via u is automatically turned off
(➔ page 38).
Selects the next song.
5 button
Performs fast reverse playback.
2 button
Apple and iPod are trademarks of Apple Inc., registered in
the U.S. and other countries.
Dock control
buttons
Stops playback.
4 button
Performs fast forward playback.
En
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Onkyo Network Tuner
Connect an Onkyo Network Tuner to the integrated
amplifier and enjoy its music. You can use the integrated
amplifier’s remote controller to control the Network
Tuner, but the functionality will depend on your Network
Tuner’s input.
8 button
About Onkyo Dock
Sets an Onkyo Network Tuner to Standby.
DIMMER button
Adjusts the display brightness.
Dock is sold separately. Use only the Onkyo Dock with
digital connections.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
Before using the Onkyo Dock components, update your
web site.
For supported iPod models, see the instruction manual of
the Onkyo Dock.
!/"/#/$ and ENTER buttons
Select and adjust settings.
To control the Onkyo Network Tuner, an u
connection is required (➔ page 22).
SHUFFLE button
Performs shuffle playback. (When the Network Tuner’s
input is set to USB or AirPlay.)
To control the Onkyo Network Tuner with the
integrated amplifier’s remote controller, you need to
change the input name to “TUNER” (➔ page 36).
MENU button
Returns to the top menu of the Internet Radio service.
(When the Network Tuner’s input is set to NET.)
REPEAT button
Cycles through the repeat back modes. (When the
Network Tuner’s input is set to USB or AirPlay.)
8
DIMMER
7 button
Selects the beginning of the current song. Pressing this
button twice selects the previous song. (When the
Network Tuner’s input is set to USB or AirPlay.)
Selects the previous Internet radio station. (When the
Network Tuner’s input is set to NET.)
Selects the previous radio preset. (When the Network
Tuner’s input is set to TUNER.)
1/3 button
Starts or pauses playback. (When the Network Tuner’s
input is set to USB, NET or AirPlay.)
!/"/#/$
ENTER
6 button
Selects the next song. (When the Network Tuner’s input
is set to USB or AirPlay.)
Selects the next Internet radio station. (When the
Network Tuner’s input is set to NET.)
Selects the next radio preset. (When the Network
Tuner’s input is set to TUNER.)
INPUT button
Tuner control
buttons
Cycles through the input sources.
En
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Integrated Amplifier as a USB Audio Device
Using the USB port on the rear panel of the A-9000R, you
can connect your PC and play back 192 kHz/24-bit HD
Playing Music Files from the PC
audio formats.
■ Operating with the remote controller
Note
Connecting a PC
• Depending on the audio player software used, the sound of
incompatible file formats may not be output.
• If you unplug the USB cable, the message “USB” flashes on the
information display.
• If the USB connector of your PC does not support the high-speed
2.0 standard, the audio will not be output.
• If there is no USB connection between the PC and the integrated
amplifier, the “USB” input can’t be selected.
INPUT !/"
■ System Requirements (PC)
USB
OS
1
®
Windows 7 (32 bits/64 bits)/
Windows Vista (32/64 bits)/
Windows XP (32/64 bits) SP3 or later
®
®
®
®
CPU
RAM
HDD
Intel Pentium 4 processor 1.6 GHz or higher processor
512 MB or greater
Press INPUT!/" repeatedly to switch the input
1
2
to “USB”.
60 MB or greater free hard drive space
Supported models
USB
Play music files from the PC.
PC/AT compatible machine equipped with a USB port
compliant with the USB standard Rev2.0 HS (Intel USB
®
host controller is recommended)
■ Operating on the integrated amplifier
PC
Windows and the Windows logo are trademarks of the
Microsoft group of companies.
INPUT selector
Installing USB drivers
To playback the audio data stored on your PC by using the
equipment via USB port connection, you must install the
driver on your PC from the following URL:
(for the other area customer)
Use the INPUT selector to switch the input to
“USB”.
1
For the installation procedure, see the above Onkyo Web
site.
Play music files from the PC.
2
En
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operations
Custom Setup
You can perform custom settings using SETUP on the
remote controller or the integrated amplifier. The SETUP
menu allows you to set the following items: NAME,
SHOW, HPLVL, ASb, ROUTE, and RESET.
■ Operating with the remote controller
■ Operating on the integrated amplifier
SETUP
INPUT selector
!/"/#/$
CD SACD MD TAPE TUNER
NAME
DOCK PC GAME TV
ENTER
RETURN
L1 L2 L3 CX1 CX2 OPT
SHOW
PNO USB AES
SETUP
HPLVL
ASb
HP -12 HP 0 HP +12
ASb-ON ASb-OFF
Press SETUP.
1
2
NORMAL PRE
MAIN SPLIT
ROUTE
Press SETUP repeatedly to select “NAME”.
Press !/" repeatedly to select “NAME”.
1
2
RESET
RST-NO RST-YES
Use the INPUT selector to select the name you want
to assign.
Note
First, the currently assigned name flashes on the
information display. Then, the assignable names are
displayed flashing.
• When “ROUTE” is set to “MAIN”, the “NAME”, “SHOW”,
“HPLVL” and “ASb” settings are not available.
• When the “USB” or “PHONO” input is selected, “NAME”
setting is not available.
Press ENTER.
The name currently assigned to the input flashes.
3
4
Press and hold down SETUP.
The selected name flashes rapidly for a few times as
the setting is confirmed.
3
4
Press #/$ repeatedly to select the name you want
to assign.
Changing Input Names
The selected name flashes.
Press SETUP repeatedly to exit the setup.
You can change the name of the currently selected input.
Choose a name from the following: CD, SACD, MD,
TAPE, TUNER, TV, GAME, PC, DOCK
Tip
Press ENTER.
The selected name flashes rapidly for a few times as
the setting is confirmed.
• By default, input names are set according to the terminal names.
5
6
Note
• If you assign a name that is already used on another input, the
name of that other input will be restored to its default.
• When the “USB” or “PHONO” input is selected, “NAME”
setting is not available.
Press RETURN repeatedly to exit the setup.
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
En
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Skipping Unused Inputs
Setting the Headphone Level
You can hide the display of those inputs that are not used,
so that they are skipped when selecting an input. Change
any input from the following: L1(LINE1), L2(LINE2),
L3(LINE3), CX1(COAX1), CX2(COAX2), OPT,
AES(AES-EBU), USB, PNO(PHONO)
You can set the volume when using headphones.
Press RETURN repeatedly to exit the setup.
6
■ Operating with the remote controller
■ Operating on the integrated amplifier
SETUP
INPUT selector
!/"/#/$
■ Operating with the remote controller
ENTER
RETURN
!/"/#/$
SETUP
ENTER
RETURN
Press SETUP.
1
2
SETUP
Press !/" repeatedly to select “HPLVL”.
Press SETUP.
1
Press !/" repeatedly to select “SHOW”.
2
Press SETUP repeatedly to select “SHOW”.
1
2
Press ENTER.
The current level is displayed.
3
Use the INPUT selector to select the input you want
to change.
Press and hold down SETUP.
The setting is switched ON/OFF.
The setting is automatically confirmed.
3
4
Press ENTER.
3
Press #/$ repeatedly to adjust the offset level.
You can adjust the offset level from -12 dB to +12 dB
in 1 dB steps.
4
5
Press !/" repeatedly to select the input you want
4
to change.
Press SETUP repeatedly to exit the setup.
The setting is automatically confirmed.
Tip
Press RETURN repeatedly to exit the setup.
• The default setting is ON.
Press #/$ to switch between ON and OFF.
5
`ON:
Note
Shows the display of selected input.
`OFF:
• The current input doesn’t appear as selectable. For example, if
the input is currently set to “LINE1”, “L1” won’t appear as
selectable.
Hides the display of selected input.
The setting is automatically confirmed.
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
En
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Auto Standby Function
■ Operating on the integrated amplifier
SETUP
When the Auto Standby (ASb) function is activated, the
integrated amplifier will automatically enter Standby
mode if there is no operation for 30 minutes with no audio
signal input.
even if it receives a signal. To turn on the integrated
amplifier, press 8ON/STANDBY on the integrated
amplifier or 8 on the remote controller manually.
INPUT selector
■ Operating on the integrated amplifier
■ Operating with the remote controller
SETUP
INPUT selector
!/"/#/$
ENTER
RETURN
SETUP
Press SETUP.
1
Press SETUP repeatedly to select “HPLVL”.
1
2
Press SETUP repeatedly to select “ASb”.
1
2
Press !/" repeatedly to select “ASb”.
2
Use the INPUT selector to adjust the offset level.
First, the current level flashes on the information
display. Then, the value is adjusted.
Use the INPUT selector to switch between
“ASb-ON” and “ASb-OFF”.
First, the current setting flashes on the information
display. Then, the setting is switched ON/OFF.
The setting is automatically confirmed.
The setting is automatically confirmed.
Press ENTER.
The current setting is displayed.
3
Press SETUP repeatedly to exit the setup.
3
Press SETUP repeatedly to exit the setup.
3
Tip
Tip
• The default level is 0.
• The default setting is ON.
Press #/$ to switch between “ASb-ON” and
4
Note
“ASb-OFF”.
`ASb-ON:
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
Note
Enables Auto Standby.
• When the Auto Standby (ASb) function is activated, Onkyo
components connected via u are automatically turned off
(➔ page 22).
`ASb-OFF:
Disables Auto Standby.
The setting is automatically confirmed.
• Before entering Standby mode with the Auto Standby (ASb)
function, the message “ASb” flashes for 30 seconds on the
information display.
Press RETURN repeatedly to exit the setup.
5
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
Once the Auto Standby (ASb) function has been activated,
the integrated amplifier will not automatically turn on
En
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Route
You can specify the function (Route) of the integrated
amplifier by selecting between Normal, Pre, Split, and
Main modes.
■ Operating on the integrated amplifier
SETUP
Press #/$ repeatedly to select the route you want
to set.
4
INPUT selector
The selected route flashes.
`NORMAL:
■ Operating with the remote controller
amplifier as is.
!/"/#/$
ENTER
RETURN
`PRE:
With this setting, you can use the integrated
amplifier as a preamplifier (➔ page 25).
SETUP
Press SETUP repeatedly to select “ROUTE”.
1
2
Press SETUP.
1
`SPLIT:
Use the INPUT selector to select the route you want
to set.
With this setting, you can use the integrated
amplifier’s pre-amp and power amp units
separately (➔ page 26).
Press !/" repeatedly to select “ROUTE”.
2
First, the current setting flashes on the information
display. Then, the selectable routes are displayed
flashing.
Press and hold down SETUP.
The selected route flashes rapidly for a few times as
the setting is confirmed.
3
4
Press ENTER.
The route currently selected is displayed.
3
`MAIN:
With this setting, you can use the integrated
amplifier as a power amplifier (➔ page 27).
When it is selected, the MAIN IN LED lights.
Press SETUP repeatedly to exit the setup.
Tip
• The default setting is “NORMAL”.
Press ENTER.
The selected route flashes rapidly for a few times as
the setting is confirmed.
5
6
Note
• In “PRE” mode, SPEAKERS can’t be used.
• In “SPLIT” mode, you need to use PRE OUT and MAIN IN.
• In “MAIN” mode, only SPEAKERS and SETUP can be used.
• In “MAIN” mode, the audio coming from MAIN IN is output by
speakers with a 32.5 dB amplification.
Press RETURN repeatedly to exit the setup.
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
En
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring the Default Settings
You can restore the default settings of the integrated
amplifier.
■ Operating on the integrated amplifier
SETUP
Press ENTER.
5
INPUT selector
If “RST-YES” is selected, “CLEAR” appears on the
information display. The integrated amplifier then
automatically turns off.
■ Operating with the remote controller
If “RST-NO” is selected, the setup returns to
“RESET”.
!/"/#/$
ENTER
RETURN
SETUP
Press SETUP.
1
Press !/" repeatedly to select “RESET”.
2
Press SETUP repeatedly to select “RESET”.
1
2
Use the INPUT selector to switch between
“RST-YES” and “RST-NO”.
First, the current setting flashes on the information
display. Then, the setting is switched while flashing.
Press ENTER.
The current setting flashes on the information display.
3
Press and hold down SETUP.
3
If “RST-YES” is selected, “CLEAR” appears on the
information display. The integrated amplifier then
automatically turns off.
If “RST-NO” is selected, the setup returns to
“RESET”.
Press #/$ to switch between “RST-NO” and
4
“RST-YES”.
`RST-YES:
Note
Restores the default settings.
• The integrated amplifier will end the setup if there is no
operation for 8 seconds.
`RST-NO:
Cancels the operation.
En
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
If you have any trouble using the integrated amplifier,
look for a solution in this section.
If you can't resolve the issue yourself, try resetting the
integrated amplifier before contacting your Onkyo dealer.
To reset the integrated amplifier to its factory defaults, see
“Restoring the Default Settings” (➔ page 40).
Headphone output is intermittent or
there’s no sound.
Audio
There’s no sound.
• This may be due to dirty contacts. Clean the headphones
plug. See your headphones’ instruction manual for
cleaning information. Also, make sure that the
headphones cable is not broken or damaged.
• Make sure that “ROUTE” is not set to “MAIN”
(➔ page 39).
• Make sure the POWER switch is set to ON.
• Make sure the integrated amplifier’s volume control is
not set to minimum (➔ page 29).
• Make sure the correct input source is selected
(➔ page 29).
• Make sure the integrated amplifier is not muted
• Make sure the speakers are connected correctly
• Check all connections and correct as necessary
(➔ page 15).
OUT output no sound (➔ page 32).
• The integrated amplifier does not support digital formats
other than PCM. Inputting a digital format other than
PCM will cause loud noise.
• If the USB connector of your PC does not support the
high-speed 2.0 standard, then audio is not output.
• If “ROUTE” is set to anything other than “NORMAL”,
make sure that each component is connected accordingly
(➔ pages 25 to 27, 39).
Power
Audio performance
• Make sure the POWER switch is set to ON.
• Make sure that the power cord is properly plugged into
the wall outlet (➔ page 18).
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
• Audio performance will be at its best about 10 to 30
minutes after the integrated amplifier has been turned on
and had time to warm up.
• Using cable ties to bundle audio cables with speaker or
power cables may degrade the sound quality, so refrain
from doing it.
• Depending on the country, the integrated amplifier may
be polarity-sensitive. In this case, plug the power cord in
a way that provides the best sound quality.
• Install the integrated amplifier on a sturdy rack or shelf.
Position it so that its weight is evenly dispersed on its
four legs. Do not install the integrated amplifier in a
place with vibration or an unstable location.
• Plug the power cord into an AC wall outlet.
The Integrated Amplifier turns off
unexpectedly.
• When the Auto Standby function is activated, the
integrated amplifier will automatically enter Standby
mode (➔ page 38).
• When the protection circuit is activated (because of
speaker short-circuit, overload, or over-current), the
integrated amplifier enters Standby mode. Remove the
source of the problem and turn the integrated amplifier
back on.
The sound quality is not good.
• Make sure the speaker cables are connected with the
correct polarity (➔ page 15).
• Make sure all audio connecting plugs are pushed in all
the way (➔ page 17).
• The sound quality can be affected by strong magnetic
fields, such as those from a TV. Try moving any such
devices away from the integrated amplifier.
waves near the integrated amplifier, such as a cellular
phone that’s being used to make a call, the integrated
amplifier may output noise.
En
41
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Playback
External Components
Remote Controller
Can’t play music files from the PC.
No sound is heard from a connected
component.
The remote controller doesn’t work
properly.
• Make sure that the USB cable is plugged in firmly
(➔ page 35).
• Make sure that the USB driver is installed successfully
(➔ page 35).
• Make sure that there is no unsupported file formats or
signals.
• Make sure the correct input source is selected
(➔ page 29).
• If “ROUTE” is set to anything other than “NORMAL”,
make sure that each component is connected accordingly
(➔ pages 25 to 27, 39).
• Make sure the batteries have been installed with the
correct polarity (+/–) (➔ page 10).
• Replace both batteries with new ones. (Do not mix
different types of batteries or new and old batteries.)
• The remote controller is too far away from the integrated
amplifier, or there’s an obstacle between them
(➔ page 10).
• The integrated amplifier’s remote control sensor is being
subjected to bright light (inverter-type fluorescent light
or sunlight).
• Make sure the analog audio cable is connected correctly
(➔ page 17).
The message “USB” flashes on the
The sound from turntable is distorted.
• The USB cable is unplugged. Plug the USB cable again.
Onkyo Dock
• The integrated amplifier is located behind the glass
doors of an audio rack or cabinet.
• If your turntable (MM/MC) has a built-in phono preamp,
connect to other analog inputs such as LINE IN.
• If your turntable (MM/MC) does not have a built-in
phono preamp, connect a turntable to PHONO
(➔ page 23).
• Make sure that the ground wire is connected. Otherwise,
it may produce an audible hum and noise.
• Make sure the MM/MC selector is set in accordance
with the cartridge format of your turntable.
There’s no sound.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
• Make sure that the Onkyo Dock is connected to the
integrated amplifier properly.
• Make sure that no video content is being played.
• Reset the iPod.
A popping noise is produced when the
power is set to on or off.
The integrated amplifier contains a microcomputer
for signal processing and control functions. In very
rare situations, severe interference, noise from an
external source, or static electricity may cause it to
lockup. In the unlikely event that this should happen,
unplug the power cord, wait at least 5 seconds, and
then plug it again.
Other
• When the Auto Standby (ASb) function is activated, the
power of the Onkyo Dock connected via u is
automatically turned off (➔ page 38).
• Turn each of the components’ power on or off in the
following order.
When turning the power on:
2. Integrated Amplifier (A-9000R)
Can’t control properly by using the
remote controller.
When turning the power off:
1. Integrated Amplifier (A-9000R)
2. Source component
Before disconnecting the power cord from the wall
outlet, set the main power switch to OFF.
• Make sure that the u cable is connected to the
integrated amplifier correctly.
If during idling the cover is too hot to touch, then
ventilation needs to be improved.
You need to change the input name to use u function
(➔ page 36).
En
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Rated Output Power
(Stereo):
■ Audio Inputs
2 ch × 75 W at 8 ohms, 20 Hz - 20 kHz,
0.05 %, 2 ch driven (IEC)
2 ch × 140 W at 4 ohms, 20 Hz - 20 kHz,
0.05 %, 2 ch driven (IEC)
Digital Inputs
Optical: 1
Coaxial: 2
AES/EBU: 1
*
450 W (1 Ω)
310 W (2 Ω)
230 W (3 Ω)
180 W (4 Ω)
100 W (8 Ω)
Dynamic Power
Digital Input Format
Digital Input Sampling Rate
2ch PCM
*
IEC60268-Short-term maximum output power
32 kHz/44.1 kHz/48 kHz/88.2 kHz/96 kHz
compatible (OPT)
32 kHz/44.1 kHz/48 kHz/88.2 kHz/96 kHz/
176.4 kHz/192 kHz compatible
(COAX, AES/EBU)
44.1 kHz/48 kHz/96 kHz/192 kHz compatible
(USB)
THD+N (Total Harmonic Distortion+Noise)
0.006 % (1 kHz, half power)
0.008 % (20 Hz - 20 kHz, half power)
Damping Factor
130 (1 kHz, 8 Ω)
Input Sensitivity and Impedance (Unbalance)
150 mV/47 kΩ (LINE)
2.25 mV/47 kΩ (PHONO MM)
0.18 mV/100 Ω (PHONO MC)
Analog Stereo Inputs
LINE 1, LINE 2, LINE 3, PHONO (MM/MC),
MAIN IN
Rated RCA Output Level and Impedance
Maximum RCA Output Level and Impedance
Phono Overload
1 V/300 Ω (PRE OUT)
5 V/300 Ω (PRE OUT)
70 mV (MM 1 kHz 0.5 %)
5.2 mV (MC 1 kHz 0.5 %)
■ Audio Outputs
Analog Outputs
Speaker Outputs
Phones
LINE OUT, PRE OUT
4
Frequency Response
10 Hz - 100 kHz/+0 dB, –1 dB 1 W/8 Ω
1 Hz - 250 kHz/+0 dB, –3 dB 1 W/8 Ω
1 (6.3 ø)
Tone Control Characteristics
Signal to Noise Ratio
10 dB, 80 Hz (BASS)
10 dB, 10 kHz (TREBLE)
■ Others
107 dB (LINE, IHF-A)
60 dB (PHONO MM, IHF-A)
70 dB (PHONO MC, IHF-A)
RI
2
PC Interface
USB
Speaker Impedance
4 Ω - 16 Ω (Speakers A or B)
8 Ω - 16 Ω (Speakers A + B)
Specifications and features are subject to change without notice.
HICC
140 A
Power Supply
AC 230 V, 50 Hz
Power Consumption
No-sound Power Consumption
Standby Power Consumption
Dimensions (W × H × D)
Weight
300 W
120 W
0.2 W
435 mm × 175 mm × 435 mm
18.5 kg
En
43
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
Y1108-1
SN 29400844
(C) Copyright 2011 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.
* 2 9 4 0 0 8 4 4 *
Download from Www.Somanuals.com. All Manuals Search And Download.
|