URC 4080/4081
VIDEO EXPERT
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Charts
FEATURES AND FUNCTIONS
Use SET for all programming
sequences.
Use the illustration below to locate One ForAll 4-Device
Video Expert remote control features and then study the Key
Charts (on the next two pages) to learn how they function.
The LED (red light) blinks to show that
the remote control is working and is
sending signals.
Use M.POWER to set up and turn on (or
off) all your video components with a
single key.Also see page 25.
Press POWER once to turn on (or off)
a selected home entertainment
component.
Press TV,DVD,VCR,or CBL/SAT once
to select a home entertainment video
component to control.
Use the F1, F2, F3, or F4 keys
to program macros.Also see page 30.
Use EXIT to exit out of your cable
converter’s menu and guide.
Press MENU once to display the selected
component’s screen menu. Use the VOL
+/- and CH +/- keys to navigate menus
and press the MUTE key to select items.
Press TV/VID to switch viewing between
TV and video sources.
Use VOL + (or VOL -) to raise (or lower)
the sound volume.
Use CH + (or CH -) to select the next
higher (or lower) channel.
Press MUTE/SELECT once to turn sound
off or on.Also,use MUTE/SELECT to
select items from the selected
component’s screen menu after
pressing MENU once.
After pressing MENU,use the Cursor
Keys to move the cursor in the program
guide and menu screens.
continued on next page...
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND FUNCTIONS
INSTALLING BATTERIES
Key Charts (Continued)
Press PIP once to view or turn off the
picture-in-picture feature.
Press SWAP once to exchange the PIP
with the main TV picture.
❶
Use MOVE to the picture-in-picture
position on the TV screen.
Press SLEEP once to enable (or disable)
a selected component’s sleep timer
(if available).
Use DISPLAY to view a selected
component’s information on the TV.
Use the keypad (0 ~ 9) to directly select
channels (e.g.,09 or 31).
❶
Press ENTER once after entering
channel numbers on some TV
models.
Press PREV.CH once to recall the
last-viewed channel.
Use V.CONFIG to custom program and
recall video configuration modes for
home theater use.Also see page 32.
❶
1.
2.
On the back of the remote control, press the
recess and slide the battery cover off (see above).
In the TV,DVD,or VCR mode,use the
FWD SCAN,REW SCAN,PLAY,STOP,and
PAUSE keys to control your VCR or DVD
(or LD) player.To record a program on,
theVCR,press REC twice.
Obtain two (2) fully-charged AA alkaline
batteries.Match the + and – marks on the
batteries to the + and – marks in the battery
case,then insert the new batteries.
3.
4.
Align the cover keys with the case openings
and slide the cover on until it locks.
Test the unit by pressing POWER and any mode
key (e.g.TV,DVD,VCR,or CBL/SAT).If batteries
are inserted correctly,the LED will blink once.
NOTE:When batteries need replacement, the One For All
4-Device Video Expert remote control will cease to operate. Simply
replace the batteries and the unit will be restored to its full func-
tionality, complete with your favorite settings.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ampro
Anam
0751
0180
PROGRAMMING TV CONTROL
Audiovox
Baysonic
Belcor
Bell & Howell
Bradford
Brockwood
Broksonic
CXC
Candle
Carnivale
Carver
Celebrity
Cineral
Citizen
0451,0180,0092,0623
0180
0019
0154
0180
0019
0236,0463
0180
0030,0056
0030
0054
0000
0451,0092
0060,0030,0056,0039,0092
0056
0180
NOTE: If you own a TV/VCR combination, skip this section and
perform“Programming TV/VCR Combo Control”on page 16.
Locate the brand name of your TV in the Setup Codes For
TVs section below, and write it in the following space.
TV Brand: __________________________________
The brands are listed in alphabetical order with the most
popular codes listed first.To program TV control:
1.
2.
Turn on the TV.
On the remote control,press TV once. Press and
hold SET until the LED blinks twice,then
release SET.
Concerto
Contec
Craig
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
0180
0054
Crosley
3.
Enter the first four-digit code for your TV. If
you perform this procedure correctly,the LED
will blink twice.
Crown
Curtis Mathes
0180,0039
0047,0054,0154,0051,0451,0093,0060,0030,0145,0056,
0039,0166,0466,1147,1347
0451,0019,0039,0092,0623,0624
0019
0145
0017,0019
0720,0774
0000
0154,0236,0463,0180,0178,0019,0179,0039,0177,0623,
0624
0030
0154
0179,0683
0180,0179,0171
0180
0047,0051,0451,0093,0178,0135,1147,1347
Daewoo
Daytron
Denon
Dumont
Dwin
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
4.
5.
Aim the remote control at your TV and press
POWER once.The TV should turn off.If it does
not respond,repeat steps 2-3,trying each code
for your brand until you find one that works.If
it still does not work,try searching for the code
(see Searching For Your Code on page 23).
Electroband
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Write your TV code in the boxes below for
future reference.
Gibralter
GoldStar
Gradiente
Grunpy
Hallmark
Harley Davidson
Harman/Kardon
Harvard
Hitachi
Infinity
Inteq
0017,0030,0019
0030,0178,0019,0056
0053,0056
0180,0179
0178
0179
0054
0180
0145,0056,0151
0054
0017
0054
0000
0053
NOTE: Remember, to use the One For All 4-Device Video Expert
remote control to operate your TV, press TV first.
Setup Codes for TVs:
AOC
Admiral
Aiko
0030,0019,0052
0093,0463
0092
Akai
0030
JBL
JCB
JVC
Alaron
0179
Ambassador
America Action
0177
0180
continued on next page...
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Sansei
Sansui
0451
0463
PROGRAMMING TV CONTROL
Sanyo
Scimitsu
Scotch
0154
0019
0178
Setup Codes for TVs (Continued):
KEC
0180
KTV
0180,0030,0039
0052
0030,0019
Scott
Sears
Semivox
Semp
0236,0180,0178,0019,0179
0047,0054,0154,0156,0178,0179,0056,0171
0180
0156
Kaypani
Kenwood
LG
0056
LXI
Luxman
MGA
0047,0054,0154,0156,0178
0056
0150,0030,0178,0019
0060,0030,0019,0056
0054,0030,0179,1254
0054,0030
0250
0178,0145
0154,0250,0463,0150,0178,0056
0047,0017,0051,0039,0135
0093,0150,0178,0019
0093
Sharp
Shogun
Sony
Soundesign
Squareview
Starlite
Supreme
Sylvania
Symphonic
TMK
0093,0165,0039
0019
0000
0180,0178,0179
0171
0180
0000
0054,0030
0171
0178,0056,0177
0093
0051,0250
0179
0051,0056
0054,0180,0150,0060,0019,0179,0056,0039,0092
0056
0031
0154,0156,0060,1256
0039
0030
0053
0054
0178,0019
0054,0165,0030,0178,0019,0179,0056
MTC
Magnavox
Marantz
Matsushita
Megatron
Memorex
Midland
Mitsubishi
Motorola
Multitech
NAD
NEC
NTC
Nikko
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Tandy
Technics
Technol Ace
Techwood
Teknika
Telefunken
Tera
Toshiba
Totevision
Vector Research
Victor
0180
0156,0178,0166
0030,0019,0056
0092
0030,0178,0092
0180
0154,0250,0166
0093,0165
0236,0463,0179
0051,0250
0047,0156,0051,0060,0030,0178,0019,0056,0039,0135,
1347
0054,0463,0030,0145,0019
0054
0030,0019,0039
0166
0019,0039,0092
0051
Vidikron
Vidtech
Wards
Philco
Philips
Pilot
White Westinghouse 0463,0623,0624
Yamaha
Zenith
0030,0019
0017,0463,0092,0624
Pioneer
Portland
Prism
Proscan
Proton
Pulsar
Quasar
RCA
0047
0178,0031,0052,0466
0017,0019
0051,0250,0165
0047,0051,0093,0019,0090,0135,1047,1147,1247,1347,
1447
Radio Shack
Realistic
Runco
0047,0154,0165,0180,0030,0178,0019,0056,0039
0154,0165,0180,0030,0178,0019,0056,0039
0017,0030
SSS
0180,0019
Sampo
Samsung
Samsux
0030,0039,0052
0060,0030,0178,0019,0056
0039
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
CCE
0278
0035
0240
0037
0240
0104
PROGRAMMING VCR CONTROL
NOTE: If you own a TV/VCR combination, skip this section and
perform“Programming TV/VCR Combo Control”on page 16.
Locate the brand name of yourVCR in the Setup Codes For
VCRs section below,and write it in the following space.
0184,0121,0209,0002,0479
0072,0278
0037
VCR Brand: __________________________________
Calix
The brands are listed in alphabetical order with the most
popular codes listed first.To programVCR control:
Canon
Carver
Cineral
Citizen
Colt
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fisher
0035
0081
0278
0037,0278
1.
2.
Turn on yourVCR and insert a video cassette.
0072
On the remote control,press VCR once. Press
and hold SET until the LED blinks twice,then
release SET.
0037,0047,0240,0072,0271
0060,0035,0041,0162
0240
0045,0278
0042
0000
0037
0037
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
3.
4.
Enter the first four-digit code for yourVCR.If
you perform this procedure correctly,the LED
will blink twice.
0032
0037,0184,0000,0121,0043,0209,0002,0278,0479
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
0047,0104
0035,0033
0000
0060,0035,0048,0202,0240
0000
0526
0037,0038
0000
0047
0000
0081,0038
0072
0000,0042,0041
0042
Fuji
Funai
GE
Aim the remote control at yourVCR and press
POWER once.TheVCR should turn off.If your
VCR remote control does not have a POWER
key, press PLAY. If theVCR does not respond,
repeat steps 2-3,trying each code listed for your
brand until you find one that works.If theVCR
still does not work ,try searching for the code
(see Searching For Your Code on page 23).
Garrard
GoVideo
GoldStar
Gradiente
HI-Q
Harley Davidson
Harman/Kardon
Harwood
Hitachi
5.
Write yourVCR code in the boxes below for
future reference.
Hughes Network
JVC
Jensen
0067,0041
0041
KEC
KLH
0037,0278
0072
NOTE: Remember, to use the One For All 4-Device Video Expert
remote control to operate your VCR, press VCR first.
Kenwood
Kodak
LXI
0067,0041,0038
0035,0037
0037
Setup Codes for VCRs:
Lloyd's
0000
Admiral
Adventura
Aiko
0048,0209
0000
0278
Logik
MEI
MGA
0072
0035
0240,0043
Aiwa
Akai
0037,0000
0041
MGN Technology 0240
MTC 0240,0000
continued on next page...
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Singer
Sony
0072
PROGRAMMING VCR CONTROL
0035,0032,0000,0033
Sylvania
Symphonic
TMK
Tatung
Teac
0035,0081,0000,0043
0000
0240
0041
Setup Codes for VCRs (Continued):
Magnasonic
Magnavox
Magnin
0278
0035,0039,0081,0000,0149
0240
0000,0041
Marantz
Marta
Matsushita
Memorex
0035,0081
0037
0035,0162,0454
0035,0037,0048,0039,0047,0240,0000,0104,0209,0454,
1037,1162,1262
0042
0048,0067,0043
0035,0048
0000,0072
0104,0067,0041,0038
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Wards
0035,0162,0202
0035,0037,0000
0000
0618
0045,0043
0037,0240
0240
0045
Minolta
Mitsubishi
Motorola
Multitech
NEC
0038
0045
0240
Nikko
0037
0240
0035
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
0060,0035,0048,0047,0081,0240,0000,0042,0072,0149
White Westinghouse 0209,0278
0037,0048,0104,0162,0454,1048,1062,1162,1262
0184,0209,0002,0479
0035,0162,0225,0454,0616,1062,1162,1262
0035,0037,0240,0042,0038
0042
0035,0209,0479
XR-1000
Yamaha
Zenith
0035,0000,0072
0038
0039,0000,0209,0033,0479
Philips
Pilot
0035,0081,0618
0037
Pioneer
Profitronic
Proscan
Protec
0067
0240
0060,0202
0072
Pulsar
0039
Quasar
RCA
0035,0162,0454,1162
0060,0035,0048,0240,0042,0149,0202
Radio Shack
Radix
0000,1037
0037
Randex
Realistic
ReplayTV
Runco
0037
0035,0037,0048,0047,0000,0104
0614,0616
0039
STS
0042
Samsung
Sanky
0240,0045
0048,0039
Sansui
0000,0067,0209,0041,0271,0479
Sanyo
0047,0240,0104
Scott
0184,0045,0121,0043
Sears
0035,0037,0047,0000,0042,0104
Semp
Sharp
Shintom
Shogun
0045
0048
0072
0240
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Write your TV/VCR Combo code in the boxes
below for future reference.
PROGRAMMING TV/VCR COMBO CONTROL
Locate the brand name of your TV/VCR Combo in the
Setup Codes For TV/VCR Combos section on the next page,
and write it in the following space.
NOTE: Remember, to use the One For All 4-Device Video Expert
to operate your TV/VCR Combo, press VCR first.
TV/VCR Combo Brand: ________________________
The brands are listed in alphabetical order with the most
popular codes listed first.To program TV/VCR control:
Setup Codes for TV/VCR Combos:
1.
Turn on your TV/VCR Combo and insert a
video cassette.
Brocksonic
Citizen
0002,0479 (TV:0463)
0278
2.
On the remote control,press VCR once. Press
and hold SET until the LED blinks twice,then
release SET.
Colt
0072
0035 (TV:0051)
0278 (TV:0624)
0002,0479 (TV:0463),0278 (TV:0624)
Curtis Mathes
Daewoo
Emerson
Funai
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
0000
GE
0060 (TV:0047),0048 (TV:0093),0035 (TV:0051),0240
GoldStar
Harley Davidson
Hitachi
0037 (TV:0056)
0000
0000
0000
3.
4.
Enter the first four-digit code for your TV/VCR
Combo.If you perform this procedure correctly,
the LED will blink twice.
Lloyd's
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
Magnasonic
Magnavox
Magnin
Memorex
MGA
Mitsubishi
Optimus
Orion
0278
0000,0081 (TV:0054)
0240
1162,1262,0162 (TV:0250),0037 (TV:0056),1037
0240
0048 (TV:0093)
1162,1262,0162 (TV:0250)
0002,0479 (TV:0463)
1162,1262,0162 (TV:0250),0035 (TV:0051)
Aim the remote control at your TV/VCR Combo
and press POWER once.The unit should turn
off.If it does not respond,repeat steps 2-3,try-
ing each code listed for your brand until you
find one that works.If it still does not work,try
searching for the code (see Searching For Your
Code on page 23).
Panasonic
Penney
Quasar
0037 (TV:0056),0035 (TV:0051),0240
0162 (TV:0250) ,0035 (TV:0051)
Radio Shack
RCA
Sansui
Sanyo
Sears
Sharp
Sony
Sylvania
Symphonic
Thomas
1037
5.
If you’ve located a TV/VCR setup code that
works your TV/VCR Combo and a separate TV
code is also listed,you’ll need to program this
code into the remote control to access volume
control (see Programming TV Control on page 8).
0060 (TV:0047),0048 (TV:0093),0035 (TV:0051),0240
0000,0479 (TV:0463)
0240
0000,0037 (TV:0056)
0048 (TV:0093)
0032 (TV:0000)
0081 (TV:0054)
0000
If there is no separate TV code listed,you will
need to perform the following steps to access
volume control:
0000
White Westinghouse 0278 (TV:0624)
Zenith 0000,0479 (TV:0463)
a. Press and hold SET until the LED blinks
twice, then release SET.
b. Enter 9 - 9 - 3.The LED will blink twice.
c. Press VCR once.The LED will blink twice.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Archer
Belcor
0153,0022,0797
0056
0014
0899
0056
0022
0022
0153
0153,0315
0025
0040
0019
0637
0002
PROGRAMMING CABLE CONVERTER OR
SATELLITE RECEIVER CONTROL
Locate the brand name of your Cable Converter or Satellite
Receiver in the setup codes section starting below,and
write it in the appropriate space.
Bell & Howell
Bell South
Cable Star
Cabletenna
Cableview
Century
Citizen
ColourVoice
Comtronics
Contec
Cable Converter Brand: ________________________
or
Satellite Receiver Brand:________________________
The brands are listed in alphabetical order with the most
popular codes listed first.To program component control:
Digi
Eastern
1.
2.
Turn on the Cable Converter or Satellite Receiver.
Emerson
Everquest
Focus
GC Electronics
Garrard
Gemini
General Instrument
GoldStar
Goodmind
Hamlin
0797
0015,0040
0400
0056
0153
0015,0797
0476,0276,0011,0810
0144,0040
On the remote control,press CBL/SAT once.
Press and hold SET until the LED blinks twice,
then release SET.
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
3.
Enter the first four-digit code for your Cable
Converter or Satellite Receiver.If performed
correctly,the LED will blink twice.
0797
0020,0259,0009,0034
0011
0007
0015,0153,0315
0003,0012,0476,0276,0014,0015,0011,0810
0440
Hitachi
Hytex
Jasco
Jerrold
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
Linsay
Memorex
Movie Time
NSC
Novaplex
Oak
Optimus
Panasonic
Panther
Paragon
Philips
0000
0063
0063
0618
0019,0007
0021
0000,0107,0021
0637
0000
0153,0025
0144,0533,0877
4.
5.
Aim the remote control at your Cable Converter or
Satellite Receiver and press POWER once.The unit
should turn off.If it does not respond,repeat steps
2-3,trying each code listed for your brand until
you find one that works.If it still does not work ,
try searching for the code (see page 23).
Write your Cable Converter or Satellite Receiver
code in the boxes below for future reference.
Pioneer
Popular Mechanics 0400
Pulsar
Quasar
RCA
Radio Shack
Recoton
Regal
Regency
Rembrandt
Runco
0000
0000
0021
NOTE: Remember, to use the One For All 4-Device Video Expert
remote control to operate your Cable Converter or Satellite
Receiver, press CBL/SAT first.
0015,0315,0797,0883
0400
0020,0259
0002
0011
Setup Codes for Cable Converters:
ABC
0003,0008,0014,0017,0007,0011,0013
Allegro
Americast
Antronix
0153,0315
0899
0022
0000
0040
SL Marx
continued on next page...
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING CABLE CONVERTER OR
SATELLITE RECEIVER CONTROL
PROGRAMMING DVD PLAYER CONTROL
Locate the brand name of your DVD (or LD) player in the
Setup Codes For DVDs (or LDs) section on the next page,
and write it in the following space.
Setup Codes for Cable Converters (Continued):
Samsung
Scientific Atlanta
Signal
Signature
Sprucer
Starcom
Stargate
Starquest
TV86
0144,0040
0008,0477,0017,0877
0015,0040
0011
DVD (or LD) Brand: __________________________
The brands are listed in alphabetical order with the
most popular codes listed first.To program DVD (or LD)
player control:
0021
0003,0015
0015,0040,0797
0015
0063
0258
0040
0418
0012,0013
0000
0015
0153,0022
0007
0153,0022,0056,0191
0063,0258
0000,0525,0899
0400
1.
2.
Turn on your DVD (or LD) player.
On the remote control,press DVD once.
Press and hold SET until the LED blinks twice,
then release SET.
Tandy
Teleview
Timeless
Tocom
Toshiba
Tusa
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
3.
4.
Enter the first four-digit code for your DVD (or
LD) player.If you perform this procedure cor-
rectly,the LED will blink twice.
Unika
United Artists
Universal
Viewstar
Zenith
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
Zentek
Aim the remote control at your DVD (or LD)
player and press POWER once.The unit should
turn off.If your DVD (or LD) player remote
control does not have a POWER key,press
PLAY.If the DVD (or LD) player does not
respond,repeat steps 2-3,trying each code list-
ed for your brand until you find one that works.
If the DVD (or LD) player still does not work ,
try searching for the code (see Searching For
Your Code on page 23).
Setup Codes for Satellite Receivers:
AlphaStar
Echostar
Expressvu
General Instrument 0627,0361,0869
HTS
Hitachi
Hughes Network
JVC
0772
0775,1005
0775
0775
0819
0749
0775
Jerrold
0627,0361
0724,0722
0724
0869
0701
0724,0722
0627,0361
0566,0143,0392,0855
0869
5.
Write your DVD (or LD) player code in the
boxes below for future reference.
Magnavox
Memorex
Next Level
Panasonic
Philips
Primestar
RCA
Radio Shack
Sony
NOTE: Remember,to use the One For All 4-DeviceVideo Expert
remote control to operate your DVD (or LD) player,pressDVD first.
0639
Star Choice
Toshiba
Uniden
0869
0790
0724,0722
0856
Zenith
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING DVD PLAYER CONTROL
(Continued)
SEARCHING FOR YOUR CODE
If your video component does not respond to the One For
All 4-DeviceVideo Expert remote control after trying all
of the codes listed for your brand,or if your brand is not
listed at all,try searching for your code.
Setup Codes for DVD Players:
Denon
GE
0490,0634
0522
For example,to search for a code for your TV:
Harman/Kardon
JVC
0582
0558,0623
0534
0503
0539
0521
0503,0627
0571
0490,0632
0503,0539
0525,0571,0632
0522
1.
2.
Turn on your TV.
Kenwood
Magnavox
Marantz
Mitsubishi
Onkyo
Optimus
Panasonic
Philips
On the remote control,press TV once.
Press and hold SET until the LED blinks twice,
then release SET.
3.
4.
Enter 9 - 9 - 1.The LED will blink twice.
Aim the remote control at the the TV and slow-
ly alternate between pressing POWER and TV.
Stop when the TV turns off.
Pioneer
Proscan
RCA
0522
NOTE: In the search mode, the One For All 4-Device
Video Expert remote control will send IR codes from
its library to the selected component, starting with the
most popular code first.
Samsung
Sharp
0573
0630
Sherwood
Sony
0633
0533
Technics
Theta Digital
Toshiba
Yamaha
Zenith
0490
0571
0503
0490,0545
0503,0591
5.
6.
Press SET once to lock in the code.
To search for the codes of your other compo-
nents,repeat steps 1 through 5,but substitute
the appropriate key (i.e.,DVD,VCR,or CBL/SAT)
for the (DVD/LD,VCR,or Cable/Satellite) com-
ponent you are searching for.
Setup Codes for LD Players:
Aiwa
0203
Denon
Funai
0059,0172
0203
Mitsubishi
NAD
0059
0059
Optimus
Panasonic
Pioneer
Quasar
Realistic
Sony
0059
0204
0059
0204
0203
0193,0201
0204
Technics
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE CODES
PROGRAMMING THE MASTER POWER KEY
FOR ALL ON/OFF
With the One For All 4-DeviceVideo Expert, you can
program the M. POWER key to turn your TV,VCR,DVD,
and Cable (or Satellite) components on and off with the
press of one button.
If you have set up the One For All 4-DeviceVideo Expert
remote control using the Searching For Your Code proce-
dure,you may need to find out which four-digit code is
operating your equipment.For example,to find out which
code is operating your TV:
1.
2.
Turn on your TV.
1.
On the remote control,press and hold SET
until the LED blinks twice,then release SET.
On the remote control,press TV once.
Press and hold SET until the LED blinks twice,
then release SET.
2.
3.
4.
Enter 9 - 9 - 5.The LED will blink twice.
Press M.POWER once.
3.
4.
Enter 9 - 9 - 0.The LED will blink twice.
Enter the following sequence*:
a. Press TV once.
To view the code for the first digit,press 1 once.
Count the number of LED blinks (e.g.,3 blinks
= 3) and write down the number in the left-
most TV Code box below.
b. Press VCR once.
NOTE: If a code digit is“0”, the LED will not blink.
c. Press DVD once.
5.
6.
Repeat step 4 three more times for remaining
digits.Use 2 for the second digit,3 for the third
digit,and 4 for the fourth digit.Finish writing
down the code in the TV Code boxes below.
d. Press CBL/SAT once.
5.
6.
Press and hold SET until the LED blinks twice,
then release SET.
To check for the codes of your other compo-
nents,repeat steps 1 through 5,but substitute
the appropriate key (i.e.,DVD,VCR,or CBL/SAT)
for the (DVD/LD,VCR,or Cable/Satellite) com-
ponent you are checking.Write down the codes
in the appropriate boxes below.
Now,when you press M.POWER once, the
remote control will direct power to your TV,
VCR,DVD (or LD) player,and Cable/Satellite
component and leave the remote control in the
TV mode.
* NOTE: If you do not want all of your equipment to power up
all of the time, you can shorten step 4 to include only those
devices you want to turn on or off. For example, to just power
up your TV and DVD (or LD) player, enter the following
sequence for step 4:
TV Code
DVD (or LD) Code
VCR Code
a. Press TV once.
b. Press DVD once.
Now when you press M.POWER once, the One For All 4-Device
Video Expert remote control will only direct power to your
DVD (or LD) player and TV, and still leave the remote control
in the TV mode.
Cable/Satellite Code
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
RE-ASSIGNING DEVICE KEYS
CHANGING VOLUME LOCK
The One For All 4-Device Video Expert remote control
can be set up to control a second TV or VCR, or any com-
bination of four video components. For example, to have
the unit control a TV, a Cable Converter, and two VCRs,
you will need to re-assign the unused DVD key to operate
the second VCR as follows:
The One For All 4-DeviceVideo Expert remote control is
preset to control the volume of a component through
your TV.
If your TV is not remote controllable,or if you would like
the volume to be controlled by a different component,you
can change theVolume Lock setting to control a volume
through a non-associated mode (e.g.,through the cable in
the TV mode).
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2.
3.
Enter 9 - 9 - 2.The LED will blink twice.
To change Volume Lock to the CBL/SAT mode:
Press VCR once,then press DVD once.The LED
will blink twice.
1.
2.
3.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
4.
Program the DVD key as a secondVCR.See
Programming VCR Control on page 12.
Enter 9 - 9 - 3 and then press CBL/SAT once.
The LED will blink twice.
To re-assign other device keys,repeat steps 1 through 4 by
substituting the key sequence from the following chart for
a desired component:
Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, the volume will be
controlled by your Cable Converter or Satellite
Receiver.
To Re-Assign
Perform Key Sequence
SET - 9 - 9 - 2 - TV - VCR
SET - 9 - 9 - 2 - DVD - VCR
To change Volume Lock to the VCR mode:
VCR as 2nd TV key:
VCR as 2nd DVD key:
1.
2.
3.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
VCR as 2nd Cbl/Sat key: SET - 9 - 9 - 2 - CBL/SAT - VCR
Enter 9 - 9 - 3 and then press VCR once.
The LED will blink twice.
VCR back to VCR:
SET - 9 - 9 - 2 - VCR - VCR
SET - 9 - 9 - 2 - TV - DVD
SET - 9 - 9 - 2 - VCR - DVD
DVD as 2nd TV key:
DVD as 2ndVCR key:
Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, volume will be
controlled by yourVCR.
DVD as 2nd Cbl/Sat key: SET - 9 - 9 - 2 - CBL/SAT - DVD
DVD back to DVD SET - 9 - 9 - 2 - DVD - DVD
To change Volume Lock to the DVD mode:
:
1.
2.
3.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
CBL/SAT as 2nd TV key: SET - 9 - 9 - 2 - TV - CBL/SAT
CBL/SAT as 2nd DVD key: SET - 9 - 9 - 2 - DVD - CBL/SAT
CBL/SAT as 2ndVCR key: SET - 9 - 9 - 2 - VCR - CBL/SAT
CBL/SAT back to CBL/SAT: SET- 9 - 9 - 2- CBL/SAT- CBL/SAT
Enter 9 - 9 - 3 and then press DVD once.
The LED will blink twice.
Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, volume will be
controlled by your DVD (or LD) player.
Upon completion of a re-assignment,the LED will blink
twice to confirm your selection.At that time,you will also
need to program the remote control to control the new com-
ponent (see previous sections on ProgrammingVCR Control,
Programming Cable Converter or Satellite Receiver Control,or
Programming DVD Player Control).
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING VOLUME LOCK (Continued)
USING KEYMOVER
The One For All 4-DeviceVideo Expert remote control
includes a Keymover feature that allows you to map (or
copy) keys from one mode (i.e.,source mode)to another
(i,e,destination mode).
To change Volume Lock back to the TV mode:
1.
2.
3.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
Enter 9 - 9 - 3 and then press TV once.
The LED will blink twice.
NOTE: The following keys cannot be mapped: TV, DVD, VCR,
CBL/SAT, SET, M.POWER, V.CONFIG, and macro keys F1~ F4.
For example,if yourVCR does not have volume control,
you can map the volume and mute keys from the TV
mode to the VCR mode as follows:
Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, volume will be
again controlled by your TV.
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
To Unlock Volume Lock:
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2.
3.
Enter 9 - 9 - 4.
For the source mode,press TV once.
2.
Enter 9 - 9 - 3 and then press VOL+ once.
The LED will blink twice.
4.
5.
6.
For the source key,press VOL + once.
For the destination mode,press VCR once.
USING THE MENU KEY
For the destination key,press VOL + once.
The LED will blink twice indicating the key-
moved sequence is correct.
On your One For All 4-DeviceVideo Expert remote con-
trol,the MENU key works just like the MENU key of your
original remote control and allows you to access the on-
screen menu of the component you have selected (e.g.,TV,
VCR, DVD,or CBL/SAT).
7.
Repeat steps 1 through 6 twice more,
substituting VOL – and MUTE as source and
destination keys in steps 4 and 6.
When you press MENU,theVOL+,VOL–,CH+,and CH –
keys will allow you to navigate and adjust the on screen
menu settings just like you would with your original
remote control.Also, the MUTE key becomes the Menu
Select key.
Upon completion of the above procedure,you can now
use your One For All 4-DeviceVideo Expert remote con-
trol to control the TV’s volume and mute in the VCR
mode, as well as in the TV mode.
To exit out of the Menu mode, press MENU or EXIT to
return to normal operation.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming A Secondary Master Power Key
With Instant Channel Selection
USING MACROS
With programming,the F1 through F4 keys on your One
For All 4-DeviceVideo Expert remote control can be setup
to perform repetitive,time-consuming operations for easy,
convenient access through the press of a single key.
Just like the M.POWER key, any F key can be programmed
to turn on and off your equipment.As an example,you
want your child to be able to easily turn on the equipment
and select a favorite premium channel.You can setup a
sequence using two macros on one F key – the first
macro will turn on the TV and tune it to channel 3,and
the second macro will turn on the Cable Box and tune it
to a desired channel (e.g.,11).
The F keys are ideal for home theater operations,setting a
favorite channel,adding to multiple component uses,
guide steps,or other multiple functions you would like to
control with one key press.
For the optimum in individual customization,you can
define and program a sequence of events,since each F
key can hold up to three macros or 12 key presses total.
Below are a few examples to get you started.
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2.
3.
Enter 9 - 9 - 5.The LED will blink twice.
NOTE: Programming a new macro over an existing one will erase
the original macro.
Select an open F key (e.g.,F2) and press
it once.
Programming A Favorite Channel
4.
Enter the following sequence:
With so many channels available through your cable
system or satellite provider,you can program a macro
that directly selects a favorite channel with one key press.
TV,
POWER,and
0-3 (or 0 -0-3 if access is over 100 channels)
For example,let’s assume your favorite cable programs
are on channel 71.Use the following instructions to pro-
gram an F key for direct access of this channel:
5.
6.
Press and hold SET until the LED blinks twice,
then release SET.
Repeat steps 1 through 5,but this time in
step 4 enter the following sequence:
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
CBL/SAT,
POWER,and
1-1 (or 0 -1-1 if access is over 100 channels)
2.
3.
Enter 9 - 9 - 5.The LED will blink twice.
Select an open Fkey (e.g.,F1) and press
it once.
4.
5.
Press TV once.
Now when you press F2 once,the TV will turn on and
tune to channel 03.When you press F2 once again, the
Cable Box will turn on and tune to channel 11.
Enter the channel number,7 - 1.
NOTE: If you have access to over 100 channels, enter
in 071.
Clearing A Macro
6.
Press and hold SET until the LED blinks twice,
then release SET.
1.
On the remote control,press and hold SET until
the LED blinks twice,then release SET.
Now when you press F1,you will instantly see cable
channel 71 on your TV set.
2.
3.
Enter 9 - 9 - 5.The LED will blink twice.
Select an F key (e.g.,F1~ F4) you want to clear
and press it once.
4.
Press and hold SET until the LED blinks twice,
then release SET.
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
6.
7.
8.
9.
Select a key from Component Group 1 (i.e.,VCR
or DVD) and press it once.Press PLAY to assign
Function Group 1 (i.e.,the transport keys).The
LED will blink twice.
USING THE VIDEO CONFIGURATION MODE
The One For All 4-DeviceVideo Expert remote control
includes a powerful Video Configuration feature that
allows you to combine the most used functions of your
Audio/Video equipment into one V.CONFIG mode. The
features you can combine are organized into five groups
and can be defined by specific modes as follows:
Select a key from Component Group 2 (i.e.,TV,
VCR,or CBL/SAT) and press it once.Press VOL+
to assign Function Group 2 (i.e.,the volume
keys).The LED will blink twice.
Function Groups
• Function Group 1 – Transport Keys (Play, Stop, Fast
Forward, Rewind, Pause, Record, Forward Scan, and
Rewind Scan)
Select a key from Component Group 3 (i.e.,TV,
VCR,or CBL/SAT) and press it once.Press CH+
to assign Function Group 3 (i.e.,the channel
keys).The LED will blink twice.
• Function Group 2 – Volume Keys (Volume Up,Volume
Down,and Mute)
Select a key from Component Group 4 (i.e.,TV,
DVD,VCR,or CBL/SAT) and press it once.Press
MENU to assign Function Group 4 (i.e.,the
menu keys).The LED will blink twice.
• Function Group 3 – Channel Keys (Channel Up,
Channel Down,Digits 0-9,Enter,Previous Channel,
Sleep, and Display)
• Function Group 4 – Menu Keys (Menu,Up,Down,Left,
Right, and Select)
Select a key from Component Mode Group 5
(i.e.,TV,VCR,or CBL/SAT) and press it once.
Press PIP to assign Function Group 5 (i.e.,the
PIP keys).The LED will blink twice.
• Function Group 5 – PIP Keys (Picture-In-Picture,Swap,
and Move)
To lock in the Video Configuration,pressSET
until the LED blinks twice,then release SET.
Component (Mode) Groups
• Component Group 1 –VCR and DVD
An Example Video Configuration
• Component Group 2 – TV,VCR,and Cable/Sat
• Component Group 3 – TV,VCR,and Cable/Sat
• Component Group 4 – TV,VCR,Cable/Sat,and DVD
• Component Group 5 – TV,VCR,and Cable/Sat
From one mode,you would like to play your DVD,use the
Volume control on the TV, change channels on your Cable
Box,control the Menu on the Cable Box,and use the PIP
feature of your TV. To program this Video Configuration
you would perform the following steps:
To enable the Video Configuration feature,you’ll need to
perform the following programming sequence:
1.
On the remote control,press V.CONFIG once.
1.
2.
On the remote control,press V.CONFIG once.
2.
Press and hold SET until the LED blinks twice,
then release SET.
Press and hold SET until the LED blinks twice,
then release SET.
3.
4.
Enter 9 - 7 - 9.The LED will blink twice.
3.
Enter 9 - 7 - 9.The LED will blink twice.
Press DVD once and then press PLAY.The LED
will blink twice.
At this point, you’ll assign Component Groups to Function
Groups up to five times,depending on how many combi-
nations you need.You can perform any of the following
steps in any order,as long as you finish the sequence with
step 9.
...continued on next page
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE VIDEO CONFIGURATION MODE
TROUBLESHOOTING
PROBLEM: LED does not blink when you press a key.
An Example Video Configuration (Continued)
SOLUTION: Replace the batteries with two (2) new AA
alkaline batteries (see page 7).
5.
Press TV once and then press VOL+.The LED
will blink twice.
PROBLEM: LED blinks when you press a key,but home
entertainment component does not respond.
SOLUTION: Make sure you are aiming the remote control at
your home entertainment component and that
you are within 15 feet of the component you are
trying to control.
6.
Press CBL/SAT once and then press CH+.The
LED will blink twice.
PROBLEM: The remote control does not control home enter-
tainment components or commands are not per-
forming properly.
7.
8.
9.
Press CBL/SAT once and then press MENU.The
LED will blink twice.
SOLUTION: Try all listed codes for the component brand
being set up. Make sure all components can be
operated with an infrared remote control.
Press TV once and then press PIP.The LED will
blink twice.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use theVCR codes for your brand. Some combo
units may require both a TV code and aVCR
code for full operation (see page 16).
To lock in the Video Configuration,pressSET
until the LED blinks twice,then release SET.
PROBLEM: No volume on a second TV.
SOLUTION: Follow instructions in Changing Volume Lock
(see page 27).
PROBLEM: CH+ , CH– , andPREV.CH do not work for your
RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the original
remote control will operate these functions.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing
ENTER to change channels,press ENTER on the
remote control after entering a channel number.
PROBLEM: Tried“Search Method”and still could not find a
working code.
SOLUTION: For help,call our technical support group at
1-330-405-8608 on any business day,between
9 A.M. and 5P.M.,EST.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on,these products require program-
ming TV codes on the remote control. For Sony,
use TV code 0000 andVCR code 0032.For Sharp,
use TV code 0093 andVCR code 0048.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
The One For All 4-DeviceVideo Expert remote control
does not have any user-serviceable parts. Opening the
case, except for the battery cover, may cause permanent
damage to your remote control.
©2000 by Universal Electronics Inc.No part of this publi-
cation may be reproduced,transmitted,transcribed,
stored in any retrieval system,or translated to any lan-
guage,in any form or by any means,electronic,mechani-
cal,magnetic,optical,manual,or otherwise,without the
prior written permission of Universal Electronics Inc.
®
One For All is a registered trademark of Universal
Electronics Inc.
Part No.URC4080
7/00
Download from Www.Somanuals.com. All Manuals Search And Download.
|