learning. Be sure to press each key within 10 seconds of the previous entry. If
not, the remote control will exit the programming mode.
3. Press and hold SET until the LED (red light) blinks twice,then
Macro keys are ideal for home theater operations,setting a favorite
channel,guide steps,or other multiple functions you would like to
control with one key press.Moreover,each macro key can hold up
to15 key presses total.
2. Enter 9 - 9 - 4.TheLED will blink twice.
set up.Make sure they can be operated with an
infrared remote control.
Press MUTE once to turn the sound off
or on.
CHECKING THE CODES
release SET.
3. Press the destination mode twice (where keymoved keys are
If you have set up the remote control using the Searching For Your
Code procedure,you may need to find out which four-digit code is
operating your equipment.For example,to find out which code is
operating your TV:
Programming A Learning Key
stored).The LED will blink twice.
PROBLEM: TV/VCR combo does not respond properly.
4. Use the Manufacturer’s Codes (on the back) to locate the type of
device and brand name and then enter the first four-digit code
for your device. If performed correctly, the LED will blink twice.
1. Press and hold SET until the LED (red light) blinks twice,then
SOLUTION: Use theVCR codes for your brand.Some combo
units may require both a TV code and aVCR code
for full operation.
In TV,VCR,DVD,SAT,andCBL modes,use
FAV to scan favorite channels and/or all
channels.See Using Channel Scan and
Programming Favorite Channel Scan.
NOTE: Programming a new macro over an existing one will erase the
original macro.
release SET.
1. On the remote control,press TV once.
8L DEVICE HOME THEATER
UNIVERSAL REMOTE CONTROL
WITH LEARNING
2. Enter 9 - 7 - 5.TheLED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try
entering the same code again.
Programming A Favorite Channel
CHANGING VOLUME LOCK
PROBLEM: Changing channels does not work properly.
2. Press and hold SET until the LED (red light) blinks twice,then
3. Press a device key once (e.g.,TV) to assign a mode for learning.
With so many channels available through your cable or satellite
system provider,you can program a macro that directly selects a
favorite channel with one key press.
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning is set at the factory for independent volume
control of each selected device.However,you may change theVolume
Lock setting to GlobalVolume Lock so that a device’s volume will be
locked to one mode (e.g.,to control TV volume in all other modes).
After that,ifdesired,youcan performIndividualVolumeUnlockon a
selected device to set its volume control for independent operation.
release SET.
5. Aim the remote control at the device and press POWER once. The
device should turn off. If it does not respond, repeat steps 2
through 5,trying each code for your brand until you find one that
works.If it still does not work,try Searching ForYour Code.
SOLUTION: If original remote control required pressing ENTER
to change channels, press ENTER on the remote
Use CH+ (or CH-) to select the next higher
(or lower) channel.
4. Press an open learning key once (e.g., L1) to store a feature to be
learned.The LED will blink rapidly for 4 seconds.If the LED does
not blink rapidly,go back to step 1 and start again.
3. Enter 9 - 9 - 0.The LED will blink twice.
control after entering the channel number.
4. To view the code for the first digit,press 1 once.Wait 3 seconds,
count the LED blinks (e.g.,three blinks = 3) and write down
the number.
For example,let’s assume your favorite cable programs are on
channel 71.Use the following instructions to program a macro key
for direct access of this channel:
PROBLEM: During learning, LED emits a long blink after pressing
5. Place your original remote control (e.g.,TV remote control)
head-to-head (about 2" apart) from the One For All 8L Home
Theater Upgradeable Universal Remote Control with Learning.
and holding key to be learned.
NOTE: If the device does not have a POWER key, press the (Play) key.
SOLUTION: A bad capture has occurred.Avoid high-ambient
light sources,such as direct daylight and fluorescent
bulbs.Try readjusting positions of remote controls
before performing the procedure again.
Press PREV once to recall the last-viewed
channel and to page back one screen on
the main menu.
NOTE: If a code digit is“0”, the LED will not blink.
NOTE: This example assumes the TV tuner is connected directly to the cable
line and not through a cable box.
6. Repeat steps 1 through 5 for each device you want to control.
For future reference,write down each working device code in the
boxes below:
Locking Volume Control To One Mode (Global Volume Lock):
6. On your original remote control,press and hold the key (i.e.,fea-
ture) to be learned until the LED on the One For All 8L Universal
Remote Control blinks twice.If the LED does not blink twice,
repeat steps 3 through 6.
5. Repeat step 4 three more times for remaining digits.Use 2 for the
1. Press and hold SET until the LED (red light) blinks twice,then
second digit,3 for the third digit,and 4 for the fourth digit.
1. Press and hold SET until the LED (red light) blinks twice,then
release SET.
release SET.
In the CD mode,use PREV to turn random
play on or off.
TV Code:
6. To check for codes of other devices, repeat steps 1 through 5,
but substitute the appropriate device key for each device you
are checking.
PROBLEM: Tried Search For Your Code method and still could not
2. Enter 9 - 9 - 3 and then press any mode key once (e.g.,TV).The
2. Enter 9 - 9 - 5.TheLED will blink twice.
3. Select an open macro key (e.g.,M1) and press it once.
4. Press TV once.
find a working code.
7. To learn functions onto other learning keys (e.g., L2 ~ L4),repeat
LED will blink twice.
In the RCVR/AMP mode,use PREV to select
the receiver band.
steps 3 through 6.
VCR Code:
DVD Code:
SAT Code:
SOLUTION: Clear the device key as follows: Press and hold
SET until the LED (red light) blinks twice,then
release.Next enter 9 - 9 - 2.Then press the device key
to be cleared twice.Now repeat the Search For Your
Code method.
3. Now,when you press VOL+, VOL–,or MUTE, the volume of the
selected device (e.g., TV) will be controlled regardless of the
mode you have selected.
USING THE HOME THEATER MODE
8. To lock in new feature(s) on the One For All 8L Universal Remote
Control,press and hold SET until the LED blinks twice,then
release SET.
Use the keypad (1 ~ 9 and 0) to directly
select channels (for example,009 or 031).
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning includes a custom Home Theater mode.
After the HOME THEATER key is programmed, it will allow you to
access five groups of remote control keys without having to change
device modes.
5. Enter the channel number,7 - 1.
Unlocking Volume Control For A Single Device (Individual
Volume Unlock):
NOTE: If you have access to over 100 channels, enter 0 -7-1.Moreover,
if the original remote control required pressing an Enter key to change
the channel, also press the Enter key after the channel number (e.g.,
0 -7-1-Enter).
9. To test a learned feature,press a device key (e.g., TV) once where
the learning mode was assigned.Then press the learning key
(e.g.,L1) where the learned feature is stored.
In the RCVR/AMP mode,use the keypad
(1 ~ 9 and 0) to select audio sources 1
through 10.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
1. After performing GlobalVolume Lock (above),press and hold
SET again until the LED (red light) blinks twice,then release SET.
SOLUTION: For power on,these products require programming
TV codes.For Sony, use TV code 0000 andVCR
code 0032.For Sharp,use TV code 0093 andVCR
code 0048.
Control Organization
CD Code:
Deleting Functions From The Learning Keys:
6. Press and hold SET until the LED blinks twice,then release SET.
2. Press a desired mode key where you want volume to be unlocked
About Control Groups
Press ENTER once after entering the
channel numbers on some TVs.
1. Press and hold SET until the LED (red light) blinks twice,then
(e.g.,RCVR/AMP) and controlled within its own mode.
Now when you press M1,you will instantly see cable channel 71 on
your TV set.
release SET.
CBL Code:
RCVR/AMP Code:
For Home Theater programming,the remote control’s keys are
grouped by type of control into the following five control groups:
3. Enter 9 - 9 - 3 and then press VOL– once. The LED will blink
2. Enter 9 - 7 - 6.TheLED will blink twice.
PROBLEM: CH+ and CH- do not work for your RCA TV.
In the CD mode,use ENTER to add 10 to
the digit entry (e.g.,ENTER and 7 is 17).
four times.
Programming A Master Power Key With Instant Channel
Selection
(1) Transport Controls: PLAY,STOP,FWD,REW,PAUSE,andREC
3. Press the device key once where the learned feature is stored
SOLUTION: Due to RCA design (1983-1987),only the original
remote control will operate these functions.
4. If desired,repeat steps 1 through 3 (of this section) for each
device that you want volume to be unlocked.
(e.g.,TV).
(2) Volume Controls:
(3) Channel Controls:
VOL+,VOL-,andMUTE
A macro key can be programmed to turn on and off your equipment
as well.For example,let’s set up a sequence that will turn on the TV
and tune it to channel 3,and then turn on the Cable Box and tune it
to a premium channel (e.g.,11).
Use TV/VID to switch the TV’s input to
view TV or video programs.
AUX Code:
4. Press the learning key (e.g., L1) to be deleted twice.The LED will
PROBLEM: No remote control of volume.
CH+,CH-,(Keypad) 0 ~ 9,ENTER,LAST,
SLEEP,INFO,andTV/VCR
5. Now,after you select a device that has volume unlocked (e.g.,
RCVR/AMP),pressing VOL+, VOL–,or MUTE,will control the
device’s volume only in its own mode.
blink twice after the second press.
SOLUTION: See Changing Volume Lock to lock/unlock volume.
Aux.Device Type: _______________________________
Use the transport keys to control your
VCR,DVD or CD player,orVOD (Video
On Demand) if available on your cable or
satellite service.
5. To clear additional functions stored on other learning keys,
repeat steps 1 through 4 (in this section).
(4) Menu Controls:
MENU,GUIDE,Cursor Controls (Up,Down,
Left,Right), SELECT,andEXIT
NOTE: This example assumes all equipment is turned off and that the TV is
connected through the cable box with TV tuning set to channel 3.
Unlocking All Volume Control (Restoring Default Setting):
This product has been discontinued and is no longer supported
CUSTOMER SUPPORT
RE-ASSIGNING DEVICE KEYS
(5) PIP Controls:
PIP,MOVE,andSWAP
NOTE: Performing these instructions will restore independent volume control
for all programmed devices (e.g., TV volume control in TV mode,VCR volume
in VCR mode, etc.).
1. Press and hold SET until the LED (red light) blinks twice,then
For assistance,please contact us in any of the following ways:
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning can be set to control a second TV,VCR,DVD
player,or other device.For example,to control a TV,a cable box,and
twoVCRs,you will need to re-assign the unused AUX key to operate
the secondVCR as follows:
About Device Groups
release SET.
PROGRAMMING TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and insert a video cassette.
To record aVCR program,press REC twice.
•
•
•
E-mail: ofasupport@ueic.com
Moreover,the remote control’s devices are grouped into the following
five device groups:
2. Enter 9 - 9 - 5.TheLED will blink twice.
1. On the remote control,press and hold SET until the LED (red
Internet: http://www.oneforall.com
Consumer Help Line: (330) 405-8616
After programming,press M1~ M4 once to
run a desired macro (see Using Macros).
light) blinks twice,then release SET.
3. Select an open macro key (e.g.,M2) and press it once.
4. Enter the following sequence:
(1) Device Group 1:
(2) Device Group 2:
(3) Device Group 3:
(4) Device Group 4:
(5) Device Group 5:
VCR,DVD,CD,andRCVR/AMP
TV,VCR,CBL,SAT,CD,andRCVR/AMP
TV,VCR,CBL,SAT,CD,andRCVR/AMP
TV,VCR,CBL,SAT,andDVD
TV
2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink
USER’S GUIDE
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.
1. On the remote control,press and hold SET until the LED (red
four times.
LIMITED WARRANTY
One For All® warrants,to the original purchaser only,that this prod-
uct will be free from defects in materials and workmanship,under
normal use,for ninety (90) days from the date of original purchase.
After programming,press L1~ L4 once
to activate a learned function (see
Using Learning Keys).
light) blinks twice,then release SET.
TV,POWER,and0-3 (or 0-0-3 if access is over 100 channels)
3. Volume will again be independently controlled according to its
default states for all programmed devices.
2. Enter 9 - 9 - 2.TheLED will blink twice.
NOTE: If the original remote control required pressing an Enter key to
change the channel, also press the Enter key after the channel number (e.g.,
0 -7-1-Enter).
INTRODUCTION
2. On the remote control,press VCR.
3. Press VCR once, then press AUX once.
ABOUT UPGRADING
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning (URC-8811) is designed to operate up to
eight home entertainment devices, including TV, video, and audio
components.The remote control requires four (4) fresh AAA alka-
line batteries (not included) and easy programming to control your
devices.For best results,please read and perform all instructions
listed here.Also, keep these instructions for future reference.
3. Press and hold SET until the LED (red light) blinks twice,then
4. The AUX key is now ready to be programmed for your second
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning has the largest infrared code library available.
However,if you purchase a brand new home entertainment or home
automation device,it may not respond to the codes stored in the
remote control’s memory.
5. Then enter the following sequence:
The default Device Group setting from the factory is:
release SET.
VCR. See Programming Device Control.
This limited warranty is valid only on ONE FOR ALL® product pur-
chased and used in the United States of America or Canada,and
does not apply to products used for industrial or commercial pur-
pose.
Use MOVE to move the window picture
to different positions in the main picture.
CBL,POWER,and1-1 (or 0-1-1 if access is over 100 channels)
6. Press and hold SET until the LED blinks twice,then release SET.
(1) Device Group 1:
(2) Device Group 2:
(3) Device Group 3:
(4) Device Group 4:
(5) Device Group 5:
VCR
TV
4. Use the Setup Codes For TV/VCR Combos (on the back) to locate
the brand name and then enter the first four-digit code for your
device.If performed correctly, the LED will blink twice.
To re-assign other device keys to the AUX key,repeat steps 1 through 4
above by substituting the sequence from the below chart:
Use SWAP to switch images and sound
between the main and window pictures.
To Re-Assign Device Key
Perform Sequence
Now when you press M2 once,the TV will turn on and tune to
channel 03.Then the cable box will turn on and tune to channel 11.
CBL
CBL
TV
If this happens,please contact our Customer Support department
(see Customer Support below) to upgrade the remote control.The
Customer Support representative will search our entire database for
a code that matches your device and instruct you how to enter it into
your One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try
entering the same code again.
AUX as 2nd TV key:
SET - 9 - 9- 2 - TV - AUX
SET - 9 - 9 - 2 -DVD- AUX
SET - 9 - 9 - 2 -SAT- AUX
SET - 9 - 9 - 2 -CD- AUX
SET - 9 - 9 - 2 -CBL- AUX
SET - 9 - 9- 2 - RCVR/AMP - AUX
Press SLEEP to activate your device’s sleep
timer (not available for all devices).
The limited warranty does not cover damage or failure caused by
products or services not supplied by ONE FOR ALL® ,or which
result from accident,misuse,abuse,neglect,mishandling,misappli-
cation,faulty installation,set-up adjustment,improper maintenance,
alteration, maladjustment of consumer controls, modifications, com-
mercial use,or that is attributable to acts of God.
AUX as 2nd DVD key:
AUX as 2nd SAT key:
AUX as 2nd CD key:
Clearing A Macro
5. Aim the remote control at the device and press POWER once. It
should turn off.If the device does not respond,repeat steps 2
through 5,trying each code for your brand until you find one that
works.If it still does not work,try Searching ForYour Code.
1. Press and hold SET until the LED (red light) blinks twice,then
Programming The Home Theater Mode
Use to turn on or off the key backlight.
When this feature is activated,keys will
remain backlight for 5 seconds after the
last key press.
release SET.
AUX as 2nd CBL key:
AUX as 2nd RCVR/AMP key:
FEATURES AND FUNCTIONS
For example,let’s assume you have a TV,a cable box,and aVCR in
your home theater system.You can set up the Home Theater mode
so that selected controls are assigned to these devices as follows:
2. Enter 9 - 9 - 5.TheLED will blink twice.
If the code for your home entertainment or home automation device
is not in our database,we will need to“capture” the code for that
device from its original remote control. A new code would then be
created and entered into your One For All 8L Home Theater
Upgradeable Universal Remote Control with Learning.If necessary,
the Customer Support representative can instruct you how to begin
the capture procedure.
Use the Key Charts (below) to learn how to use the universal features
and functions of the One For All 8L Home Theater Upgradeable
Universal Remote Control with Learning (URC-8811).
3. Select a macro key (e.g.,M1~ M4) you want to clear and press
You can also re-sassign another unused device key by substituting an
open key for the AUX key in the above chart and performing the
sequence.For example,to re-assign an unused SAT key as a 2nd CD
key, perform SET - 9 - 9 - 2 -CD- SAT. When a re-assignment is done,
the LED (red light) will blink twice to confirm your choice.At that
time,you will need to program the remote control for the new device
(see Programming Device Control).
NOTE: If the device does not have a POWER key, press the (Play) key.
it once.
1. On the remote control,press HOME THEATER.
Use SET for all programming sequences.
6. If you’ve located a setup code that works,but it has a separate TV
code,you’ll also need to program it into the remote control to
access volume control as follows:
There are no express warranties except as listed above.ONE FOR
ALL® SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES,INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY
PERIOD SET FORTH ABOVE.Some states do not allow the exclusion
or limitation of incidental or consequential damages,or limitations
on how long an implied warranty lasts,so the above exclusions or
limitations may not apply to you.This warranty gives you specific
legal rights and you may also have other rights which vary from
state to state.
4. Press and hold SET until the LED blinks twice,then release SET.
Key Charts
2. Press and hold SET until the LED (red light) blinks twice,then
USING CHANNEL SCAN
release SET.
The LED (red light) blinks to show that
the remote control is working and is
sending signals.
In the TV,VCR,DVD,SAT,andCBL modes,use the FAV key to start a
3-second scan of all favorite channels (if programmed – see
Programming Favorite Channel Scan below) and/or all channels for
the selected mode.
3. Enter 9 - 7 - 9.TheLED will blink twice.
a. Press TV once. The LED (red light) will blink twice.
NOTE: One For All reserves the right to replace a returned remote control with
a new one of equal or superior functionality.
4. Select a device.For this example,press VCR once. Then assign a
desired Control Group to the device. For this example, press PLAY
once,which will assign the entire group of Transport Controls
(i.e.,PLAY,STOP,FWD,REW,PAUSE,andREC) to theVCR.The LED
will blink once.
b. Enter the TV code for your TV/VCR Combo.If correct, the
USING KEYMOVER
INSTALLING BATTERIES
LED will blink twice.
Upgrade Exclusions
`
Press TV,VCR,DVD,AUX,SAT,CD,CBL,or
RCVR/AMP once to select a desired home
entertainment device to control.
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning includes a Keymover feature that allows you
to map (or copy) keys from one mode (i.e.,source mode) to another
mode (i.e.,destination mode).
NOTE: For VCR/TV Combos programmed with separate TV codes,
TV volume is controlled by pressing VCR first and then TV.After that,use
VOL+ (or VOL-) to raise (or lower) the TV volume. For other alternatives on
controlling your volume keys, see the“Changing Volume Lock”or“Using
Keymover”sections.
1. If Favorite Channel Scan has been set up, skip to step 2.
1. On the remote control’s back,push the tab and lift off the
battery cover.
•
•
Home entertainment or home automation devices controlled by
radio frequency (RF/UHF),wired,or ultrasonic remote controls.
Only devices controlled by infrared remote controls are covered.
Otherwise,press TV,VCR,DVD,SAT,or CBL once.
2. Press FAV once.
5. Select another device.For this example, press TV once. Then
assign a desired Control Group to this device.For this example,
press VOL+ once,which will assign the entire group of Volume
Controls (i.e.,VOL+,VOL-,andMUTE) to the TV.The LED will
blink once.
After programming,press HOME THEATER
once to select the home theater mode (see
Using The Home Theater Mode).
2. Obtain four (4) new (fully-charged) AAA alkaline batteries.
Match the + and – marks on the batteries to the + and – marks
in the battery case,then insert the new batteries.
NOTE: The following keys cannot be used as a source or destination: TV, VCR,
DVD, AUX, SAT, HOME THEATER, CD, CBL, RCVR/AMP,andSET.
Home entertainment or home automation devices not controlled
by remote controls.
•
•
IfFavorite Channel Scan has been set up,scanning of favorite
channels will start and,upon completion,continue to scan all
channels upward for the same device.
To obtain warranty service for a defective product during the war-
ranty period,please return the product,preferably in the original
carton, along with your purchase receipt, to the store of original pur-
chase.A note detailing the complaint would be helpful.The store,at
its option,will replace or repair this product if found to be defective.
7. For future reference,write down the working TV/VCR combo
code in the below boxes:
Programming Keymover
•
•
•
Broken or defective product.
3. Press the battery cover back into place.The tab should click
when the cover is locked.
Press POWER once to turn on or off the
selected device.
IfFavorite Channel Scan has not been set up,scanning will
start with the current channel,then proceed to the next
channel up,and continue until all channels of the selected
device is scanned.
For example,if yourVCR does not have volume control,you can
map the volume and mute keys from the TV mode to the VCR mode
as follows:
Products that operate over 100 kHz.
6. Select another device.For this example, press CBL once. Then
assign a desired Control Group to this device.For this example,
press CH+ once,which will assign the entire group of Channel
Controls (i.e.,CH+,CH-,(Keypad) 0 ~ 9,ENTER,LAST,SLEEP,
INFO,andTV/VCR) to the Cable Box.The LED will blink once.
TV/VCR Code:
Infrared keyboards and infrared pointing devices (such as
mouse substitutes).
4. Test the remote control by first pressing POWER and then any
mode key (e.g., TV).If batteries are inserted correctly,the LED
(red light) will blink once.
Press MENU once to display your selected
device’s main menu.
One For All
(330) 405-8655
TV Code (if used):
1. Press and hold SET until the LED (red light) blinks twice,then
•
All products for sale and/or use outside the continental United
States,Hawaii,Alaska,or Canada.
3. To stop scanning channels at any time,press any key once
(except the backlight key ).
release SET.
Use GUIDE to display your selected
device’s program guide or setup menu.
NOTE: When batteries need replacement, the remote control will stop
operating. Remove the old batteries and insert new ones to ensure all of
your programming information is restored.
7. To add additional Menu functionality to the Cable Box,press CBL
once. Then press MENU once. This action will assign the entire
group of Menu Controls (i.e.,MENU,GUIDE,Cursor Controls (Up,
Down,Left,Right),SELECT,andEXIT) to the Cable Box.The LED
will blink once.
2. Enter 9 - 9 - 4.TheLED will blink twice.
3. For the source mode,press TV once.
4. For the source key,press VOL+ once.
5. For the destination mode,press VCR once.
6. For the destination key,press VOL + once.
ADDITIONAL INFORMATION
As you update your home entertainment system,One For All® has
a universal remote control that will fit your needs.Look for these
exciting products at a retailer near you.
TROUBLESHOOTING
PROGRAMMING FAVORITE CHANNEL SCAN
In the TV,VCR,DVD,SAT,or CBL mode,you can store a list of up to
10 favorite channels,in any order,that will be immediately scanned
when FAV is pressed (see Using Channel Scan).
PROBLEM: If you own a satellite that uses code 0775 (ExpressVu
and Echostar) and your exit key does not work,per-
form the following sequence to activate this
feature/function.
SEARCHING FOR YOUR CODE
Use EXIT to exit from your selected
device’s guide or menu.
If your device does not respond to the remote control after trying all
codes listed for your brand,or if your brand is not listed at all,try
searching for your code.
One For All Access 3 ..............................................................URC-3605
One For AllVideo Expert 4 Device .......................................URC-4081
One For AllVideo Expert Plus 4L .........................................URC-4880
One For All Access 4 ..............................................................URC-4605
One For All Access 5 ..............................................................URC-5705
One For All 6 Device Home Theater .....................................URC-6011
One For All 8 Device Home Theater .....................................URC-8011
8. To add PIP functionality to the TV,press TV once. Then press PIP
once. This action will assign the entire group of PIP Controls (i.e.,
PIP,MOVE,andSWAP) to the TV.The LED will blink once.
NOTE: Only channels of one mode can be stored for Favorite Channel Scan.
PROGRAMMING DEVICE CONTROL
Use INFO to display the current channel
and program information.
SOLUTION: 1. Press the CBL/SAT key
1. On the remote control,press TV,VCR,DVD,SAT,or CBL once.
7. The LED will blink twice indicating the keymoved sequence
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning is preprogrammed at the factory to operate
an RCA TV andVCR,a Motorola (GI) cable box,an RCA satellite
receiver,a Pioneer CD player,a Toshiba DVD player,a Pioneer audio
receiver/ amplifier,and a One For All home automation device.To
control devices other than the default brands,perform the following
steps; otherwise skip this section:
For example,to search for a code for your TV:
2. Press and hold the SET key until the red LED blinks
twice
is correct.
9. To exit Home Theater programming,press and hold SET until the
2. Press and hold SET until the LED (red light) blinks twice,then
Use the cursor keys to move the cursor in
the program guide and menu screens.
Use SELECT to choose options from your
selected device’s menu or guide.
1. On the remote control,press TV once.
LED (red light) blinks twice,then release SET.
release SET.
8. Repeat steps 1 through 7 twice more,substituting VOL– and
3. Press 9-9-4,the red LED will blink twice
4. Press SET and release (one blink on LED)
5. Press 3-3-6
MUTE as source and destination keys in steps 4 and 6.
2. Press and hold SET until the LED (red light) blinks twice,then
Operating The Home Theater Mode
3. Enter 9 - 9 - 6.TheLED will blink twice.
release SET.
Upon completion of the above procedure,you can now use your
One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning to control the TV’s volume and mute in the
VCR mode,as well as in the TV mode.
After programming the Home Theater key (see previous),you simply
activate this mode by pressing HOME THEATER once. Instantly, groups
of remote control keys will be assigned to their programmed devices.
4. Use the keypad to enter a favorite channel number (e.g.,031).
3. Enter 9 - 9 - 1.TheLED will blink twice.
Then press SET once.
In the CD mode,use SELECT to select a
compact disc.Use ▲ (or ▲) to select the
next (or previous) CD.Use (or ) to
select the next (or previous) track.
One For All 8L Device Home Theater
with Learning Capability.......................................................URC-8811
6. Press the EXIT key,the red LED will blink twice.
NOTE: If the original remote control required pressing an Enter key to
change the channel, also press the Enter key after the channel number (e.g.,
0 -3-1-Enter).
4. Aim the remote control at the the TV and slowly alternate
NOTE: For TV/VCR Combo control, see the next section.
For the above example,pressing HOME THEATER once would assign
the following keys to theVCR,TV,and Cable Box:
between pressing POWER and TV. Stop when the TV turns off.
The Exit key will now correctly perform the exit fea-
ture/function on your satellite.
One For All A/V LCD 8 Device With Learning.....................URC-8910
One For All IR/RF LCD 8 Device With Learning..................URC-9910
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key
1. Turn on a device (e.g.,VCR or DVD player) and,if applicable,
insert media (e.g.,cassette or disc).
NOTE: In the search mode, the remote control will send IR codes from its
library to the selected device, starting with the most popular code first.
VCR:
PLAY,STOP,FWD,REW,PAUSE,andREC
5. If desired,repeat step 4 (in this section) for each favorite channel
to be stored,up to a total of 10 channels.
In the RCVR/AMP mode,use SELECT to
set the surround sound.Use ▲ (or ▲)
to adjust the volume higher (or lower).
Use (or ) to adjust the balance left
(or right).
PROBLEM: LED (red light) does not blink when you press a key.
ONE FOR ALL® is the registered trademark of Universal Electronics
Inc.Computime International Ltd.is the Licensee of the ONE FOR
ALL® brand for USA and Canada.
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.
1. Press a device key that has a keymoved key.
TV:
VOL+,VOL-,MUTE, PIP,MOVE,andSWAP
5. To lock in the code,press and hold SET until the LED blinks
SOLUTION: Replace batteries with four new AAA alkaline batteries.
NOTE: If you try entering more than 10 channels, the remote control will
automatically exit programming.
2. Press and hold SET until the LED (red light) blinks twice,then
Cable Box:
CH+,CH-,(Keypad) 0 ~ 9,ENTER,LAST,
SLEEP,INFO,TV/VCR,MENU,GUIDE,
Cursor Controls (Up,Down,Left,Right),
SELECT,andEXIT
twice,then release SET.
PROBLEM: LED blinks when you press a key,but home entertain-
release SET.
Copyright 2002 by Universal Electronics Inc.No part of this publication
may be reproduced,transmitted,transcribed,stored in any retrieval
system,or translated to any language,in any form or by any means,
electronic,mechanical,magnetic,optical,manual,or otherwise,with-
out the prior written permission of Universal Electronics Inc.
ment device does not respond.
6. To search for the codes of your other devices,repeat steps 1
through 5,but substitute the appropriate device key for the
device you are searching for.
2. On the remote control,press a device key once (i.e.,TV,VCR,DVD,
6. To exit programming,press and hold SET for 3 seconds.The LED
3. Enter 9 - 9 - 4.TheLED will blink twice.
AUX,SAT,CD,CBL,or RCVR/AMP).
SOLUTION: Make sure the remote control is aimed at your
home entertainment device and is not farther
than 15 feet away.
will blink twice.
Use VOL+ (or VOL-) to raise (or lower) the
sound volume.
4. Press the destination key twice (where the keymoved key is
NOTE: Use the AUX key to program control of home automation devices as
well as miscellaneous audio services and video accessories.Alternately, use
the AUX key to program control of a second device type (e.g., a second VCR;
see“Re-assigning Device Keys”).
USING MACROS
USING LEARNING KEYS
Use the learning keys (L1~ L4) to add functions that are unique to
your home entertainment devices (e.g.,VCR Tracking Up or Down).
stored).The LED will blink twice.
The One For All® 6 Device Universal Remote Control is
compatibile for use in North America,excluding Mexico.
With programming,the M1 through M4 keys on your One For All 8L
Home Theater Upgradeable Universal Remote Control with Learning
can be setup to perform repetitive,time-consuming operations for
easy,convenient access through the press of a single key.
Restoring All Keymoved Keys In A Single Mode
PROBLEM: The unit does not control home entertainment devices
or commands are not working properly.
1. Press and hold SET until the LED (red light) blinks twice,then
URC-8810w/8811
02/02
release SET.
NOTE: Please have your original remote controls handy before programming
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION: Try all listed codes for the device brands being
|