24993
Universal Remote
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Battery Installation
1. On the back of the remote, push down on the
tab and lift the cover off.
2. Match the batteries to the + and - marks inside
the battery case, then insert 2 AAA Alkaline
batteries.
3. Press the battery cover back into place.
Battery Saver
Your remote automatically turns off if the buttons
are depressed more than 30 seconds. This will
save your batteries should your remote get stuck in
a place where the buttons remain depressed (e.g.,
between the sofa cushions).
Code Saver
You will have up to 10 minutes to change the
batteries in your remote without losing codes you
have programmed. However, do not press any
buttons until batteries are installed in the remote.
If buttons are pressed without batteries in the
remote, all codes will be lost.
Code Setup
The SETUP button is used to setup the remote.
You can either setup the remote using the code
for your brand of product, from the code tables (on
separate sheet), or you can search through the
library of codes until you find a code that works for
your product. Please refer to “Code Search” page
8 for more information on using the code search
feature to learn how to search through the library of
codes for your products. NOTE: You can store any
kind of code under any mode (except TV). I.e., you
can store a DVR code under the CABLE button, or
a DVD code under the DVR button, etc. However,
you can only store TV codes under the TV button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Some buttons on the remote might have functions that
are referred to by different names on the device you
are controlling. E.g., LAST may be called RECALL,
or ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.g., your product must have LAST ability for
the LAST button to operate this feature.
TV, DVD, etc. Selects
product to be operated.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
MUTE Turns off the
TV sound while the
picture remains.
OK Selects menu
items for the device
you are controlling.
PREV. CH Returns to
the previously selected
channel.
EXIT Exit On-Screen
Menus and/or Return
to previous On Screen
selection.
SETUP For setup.
SHIFT Accesses
shifted functions.
DOT Used to
select digital chan-
nels, e.g., 2.3.
RECORD, PLAY, STOP,
REW, FF, PAUSE DVR
control buttons operate your
DVR even when the remote
is set to operate the TV.
Also operates DVD Scan
-/+. Note the DVR keys also
control DVD when in DVD
Mode.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions, cont.
Red Indicator
CHANNEL Up/Down
Lights when any but-
ton is pressed.
Changes the channels.
INPUT
For some TVs, press
repeatedly to select
from available viewing
sources (antenna, cable
box, DVR, etc.).
INFO button brings up
DVD Display or Control
Menu for Chapter/Track/
Title number, Time re-
maining/elapsed indica-
tion, system information,
etc.
MENU
Selects the on-screen
menu.
NUMBERS
Enter numbers for direct
channel selection. Some
products require ENTER
to be pressed after chan-
nel selection.
ENTER
For some TV models,
used after direct chan-
nel number
entry to immediately
change to the
ON-OFF Turns
device On or Off.
selected channel.
Note: The REC button must be pressed TWICE to record
from your DVR. For some brands of DVRs, you might
need to press the REC button once, then press it again
for three seconds.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Functions
This remote controls many DVD functions. The
descriptions may vary from your original remote
descriptions.
REW and FF buttons control the speed of Fast
Forward and Reverse Playback respectively.
CHAN+/CHAN- buttons respectively locate the
succeeding or preceding Chapters or Tracks on a
disc.
INFO button brings up DVD Display or Control
Menu for Chapter/Track/Title number, Time remain-
ing/elapsed indication, system information, etc.
MENU brings up the DVD disc Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
arrows.
OK button is used for on-screen Menu selection.
Note some DVD players require the Play button to
be used.
EXIT Exit On-Screen Menus and/or Return to pre-
vious On-Screen selection.
PLAY button is used to start Disc playback and for
Menu selection on some DVD players.
STOP button stops Disc playback.
PAUSE button pauses Disc playback - press PLAY
to resume.
INPUT brings up the DVD Players Setup Menu.
Note, not all DVD Players support all the functions
described above.
SAT Functions
CHAN+ and CHAN- buttons perform the “Page+”
and “Page-” function for on-screen Guide Menus
used by some Satellite systems.
INFO button brings up Satellite Display screen for
current Channel and system information.
MENU brings up the Satellite Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
arrows.
OK button is used for on-screen Menu selection.
EXIT button is used to Exit or Clear on-screen
Menu displays.
INPUT button performs the Satellite
TV/SAT function.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Code Entry
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
2. Press and release the desired mode
button (TV, DVR, etc.). The red
indicator blinks, then stays lit.
3. Enter the 4-digit code from the code
tables (on separate
sheet). Note: after a
valid code entry, the
red indicator turns
off. For an invalid
code, the red indicator
flashes.
4. With your device on,
press ON/OFF. If the
device turns off, no
further programming
is required. Note: If
some buttons do not operate your
equipment, try one of the other codes
for your brand.
Write your codes down here for easy reference
later.
Device
Device stored Code
TV
TV
DVD
CBL/SAT
DVR/AUX
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Search
If your device does not respond after you have
tried all the codes for your brand, or if your brand is
not listed, try searching for your code by following
these steps.
1. Manually turn on the device (TV, DVR, etc.) to
be controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
3. Press and quickly release the desired
mode button (TV, DVR, etc.). The red
indicator blinks off once.
4. Press the CHAN+ button repeatedly
(up to 300 times) until the device to be
controlled changes channel.
The red indicator blinks off
with each button press. If
you accidentally overshoot
the code required, press the
CHAN- button to backtrack through the library
until the device changes channel. Pressing
CHAN+ changes direction to forward again.
ꢀ. Press and release ENTER to install the code.
Most users will store DVR codes under the DVR
button, Cable codes under CABLE, etc. If
(for example) you want to store a DVR code
under CABLE, first follow the procedure
for Direct Code Entry (page 7) and press
CABLE in step 2 of Direct Code Entry, then
enter ANY DVR code in step 3 of Direct Code En-
try. Then follow the steps above for Code Search.
Note: If the device does not have a CHAN+ button,
use PLAY (DVR only) or POWER instead. Code Search
starts from the currently stored three digit number under
that mode. Sometimes the first code that “works” with
your device may only allow limited functionality (e.g.,
the MENU button might not work). There may be a code
that performs more functions. Continue the code search
process until the best code is found.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Identification
The Code Identification Feature allows you to
identify the 4-digit library code stored under your
device key. For example, if you want to find out
what 4-digit code is stored under your TV device
key, follow the six steps below:
1. Press and hold the SETUP button
until the red indicator stays on.
Release the SETUP button.
2. Press and release the desired mode
button (TV, DVR, etc.). The red
indicator blinks, then stays lit.
3. Press and release the SETUP
button. The red indicator blinks once
and remains lit.
4. To find the first digit for the code
stored under the mode key pressed
in step 2, press each
numeric key from 0-9 in
turn. The number that
causes the indicator
light to blink is the first
digit in your code.
5. To find the second digit,
repeat step 4.
6. Repeat step 4 again to
find the third and fourth
digits. This time the red
indicator turns off and
stays off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote
SHIFT
Press SHIFT (Setup) prior to the shifted key func-
tion, e.g., for MENU - press and release SHIFT
(Setup) then MENU (Info).
UP - press and release SHIFT then UP (Chan+).
DOWN - press and release SHIFT then DOWN
(Chan-).
LEFT - press and release SHIFT then LEFT (Vol-).
RIGHT - press and release SHIFT then RIGHT
(Vol+).
OK - press and release SHIFT then OK (Mute).
EXIT - press and release SHIFT then EXIT
(Sleep).
The red indicator blinks for each keypress.
Controlling Devices with Separate
Power On and Off Buttons
Some GE, RCA and ProScan models require
you to press the device button for more than one
second to turn the device on and the POWER
button to turn the device off.
Controlling Combo Devices
Some Combo devices (e.g., TV/DVR, TV/DVD,
DVD/DVR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/
DVD Combo, you might need to set up one code
under the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
DVR/DVD Punch-Through
This remote allows the 6 DVR transport buttons
(i.e., PLAY, PAUSE, STOP, FF, REWIND, and
REC) to Punch-Through control from any Mode
programmed with TV, SAT or Cable codes to the
last DVR, or DVD programmed Mode you used.
This feature will not operate if the programmed
TV, SAT or Cable code has its own DVR transport
button control, e.g., a TV Combo, SAT/PVR, etc.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote, cont.
Volume/Mute Control and Punch-
Through
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own
then those buttons will punch-through control to
the TV Mode device without needing to change to
TV Mode.
Setting ALL Volume/Mute Control to
any one Mode
This routine can set all Modes to “punch-through”
to any one chosen Mode for Volume/Mute button
control without the needing to change to that
Mode.
1. Press and hold the SETUP button
until the red indicator turns on,
then release the button.
2. Press and hold the MUTE button
until the red indicator blinks off,
then release the button.
3. Press and release the desired
Mode button (TV, DVR, etc.) for
Volume/Mute control, the red
indicator blinks then stays on.
4. Press and release the MUTE
button and the red indicator turns
off. The red indicator will blink
rapidly for three seconds if the
Mode you have selected has no
Volume/Mute control.
All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Using Your Remote, cont.
Setting any Mode to use its own
Volume/Mute Control
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode
has no Volume/Mute functions of its own then the
Volume/Mute buttons will do nothing.
1. Press and hold the SETUP button
until the red indicator turns on,
then release the button.
2. Press and hold the MUTE button
until the red indicator blinks off,
then release the button.
3. Press and release the desired
Mode button (TV, DVR, etc.), the
red indicator blinks then stays on.
4. Press and release the VOL-
button, the red indicator blinks
then stays on.
ꢀ. Press and release the MUTE
button and the red indicator turns
off.
Your chosen Mode will now use its
own Volume/Mute control.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remote does not operate your product.
•
Press the mode button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some
features of your product.
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
•
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Red Indicator blinks after you program
a product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
Lost Your Codes?
Enclosed with this remote is a sticker on which
you should write the codes for each device you
programmed. Apply the sticker to the back of
the remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
14
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Day Limited Warranty
Jasco Products Company warrants this product
to be free from manufacturing defects for a period
of ninety days from the original date of consumer
purchase. This warranty is limited to the repair
or replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit.
This warranty is in lieu of all other warranties
express or implied. Some states do not allow
limitations on how long an implied warranty lasts
or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations
may not apply to you. This warranty gives you
specific rights, and you may also have other rights
which vary from state to state. If unit should prove
defective within the warranty period, return prepaid
with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114-220ꢀ
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
24993
Universal Remote
Instruction Manual
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114-220ꢀ
Made in China
24993-2/09
Download from Www.Somanuals.com. All Manuals Search And Download.
|