AB2/AB2 HTS INSTALLATION INSTRUCTIONS
These fasteners and tools are provided
�
�
AB2 HTS
AB2 HTS
Step 1
Identify parts
(1) (5) M4 X 12mm Phillips
(2)
(1)
(1)
(10) Plastic anchor
pan head machine screw
(1) (5) M5 X 12mm Phillips pan
head machine screw
(5) 8-32 X 5/8'' Phillips pan
head machine screw
Mounting plate (1)
(2) (10) #12 X 3/4" Phillips pan
head self-tapping screw
(5) Circular nut (PEM)
8-32 thread
�
� � � ��� � ���� �
(2) (10) #12 X 1-3/4'' Phillips pan
head self-tapping screw
(1)
(5) 1/4-20 X 1" Phillips pan
head machine screw
(1) (5) 5/32'' Hex key
(1)
(2) 3/32'' Drill bit
Screw covers
Extension
� �� � ��
Additional installation tools
Phillips Head Screw Driver
�
Pencil
Adjusting knuckle
Electric Drill
Mounting plate (2)
Drill Bits: 1/8'' drill bit for drywall
Speaker plate
1/8”
5/16'' masonry bit for cement wall applications
5/16'' mason bit
Wall
Ceiling
�
Wall
�
Step 2
Decide on location
Mounting to drywall.
Step 3 Installation of the wall plate
1. Use the wall plate as a template and mark the screw hole locations onto the surface using a pencil.
2. Drill into the drywall with a 1/4'' drill bit. Insert the anchors into the hole as shown in fig. 3.
3. Secure with the #12 x 1-3/4'' screws, see fig. 4.
�
� �� �� �
��� ���
��� ���
�
�
Mounting to solid concrete or cinder block.
1. Drill into the surface with a 3/16'' masonry drill bit 1-3/4" deep and insert the anchors into the holes as shown in Fig. 3
2. Secure wall plate with the #12 x 1-3/4" , see fig. 4.
�
� �� �� �
��� ���
��� ���
�
�
�
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
Installation of wall plate (continued)
Step 4
Installation of speaker plate onto speaker
Mounting to solid wood or wood studs.
Drill a pilot hole into center of each location using 3/32" drill bit (provided),
Drill 1-1/4'' into stud. Attach the plate with two #12 x 1-3/4" wood screws.
®
1. Bose speakers with 4MM or 5MM inserts.
fig. 3
fig. 2
��� ���
� �
fig. 6
��� ���
2. Speakers with single factory installed threaded insert.
fig. 4
� � ��
wall
wall
� �
� �
Step 5
Installation of adjusting knuckle
and extension.
3. Speakers with 2 installed 1/4''-20 or 6MM x 15MM threaded inserts.
�
�
�
Set screw location
1/4''-20 x 5/8'' or
6MM x 15MM
Screw covers
�
(not supplied)
Set screw locations
4. Speakers with a single keyhole in back.
Extension
Insert into keyhole and slide upward then tighten.
Set screw location
5. Speakers without mounting holes - wood cabinet only.
� �� �
#12 x 3/4''
�
3/32'' drill bit
OmniMount Systems, Inc.
The Pointe at South Mountain
8201 South 48th Street
Phoenix, Arizona 85044-5355
Toll free 1-800-MOUNT-IT
(480) 829-8000
100% Replacement Warranty
�
Audio Basics products are engineered and manufactured to the highest standards. In the event that there are defects in materials,
workmanship, or missing parts, OmniMount Systems will, at its discretion, repair or replace your Audio Basics product. Claims that
are submitted must include either the sales slip or proof of purchase.
Copyright 2004 OmniMount Systems, Inc.
All rights reserved. OmniMount products
are covered by patents issued and/or
pending. “OmniMount” is a registered
trademark of OmniMount Systems, Inc.
"Audio Basics" is a trademark of
If OmniMount products are used for purposes other than their original intent, OmniMount Systems, its distributors and retailers shall
not be held responsible or liable for injuries or property damage, direct, indirect or consequential, which may arise from the inability
to use this product safely, properly, and in the manner for which it has been designed and manufactured.
This warranty does not apply to products which have been lost, damaged by misuse, abuse or accident, altered or repaired in any
way other than specified by OmniMount Systems, Inc.
This warranty is non-transferable.
For installatioDn aosswisntalnoceapdleafsreocmall Wourwtowll f.rSeeohmelpalinneuaat l1s-8.c00o-mMO.UANTll-ITManuals Search And Download.
OmniMount Systems, Inc.
AB-2 revision 2, 1/04 Part #1000254.
Fax: (480)756-9000
email: [email protected]
|