START HERE
2
3
4
Turn on the Unit
Using This Quick Start Manual
To Change the Input Type:
Connecting the Sensor Input
1. Apply power to the unit. The unit initializes,
flashing ÒTHERMISTORÓ. Then the temperature
should appear.
Use this Quick Start Manual to set up your controller
and begin operation. Information is provided on how to:
1. Press MENU until the display
1. Locate the TB2 (TB3 on Version #1) connector on
the rear of the unit.
shows ÒINPTÓ:
¥
¥
¥
Connect ac power
2. Connect sensors, referring to the appropriate
diagram below and tighten down lockdown
screws.
ᮡ
ᮣ
/MAX
SETPTS
/MIN
MENU
RESET
2. Verify that a temperature is displayed. If not:
Connect sensor input
Set basic options for operation
¥
¥
¥
¥
Remove ac power
ᮣ
2. Press /MIN to show current input
3. Tug gently on the wires to verify the connections.
4. Replace the panel at the back of the unit.
Verify the TB1 power connections
Check your power source
Apply power again
For complete information on all setup options, see the
OperatorÕs Manual.
type:
ᮡ
ᮣ
/MAX
SETPTS
/MIN
MENU
RESET
Before You Begin
1
2
3
In addition to the controller and the related parts, you
will need the following items to set up your unit:
ᮡ
3. Press /MAX to select the setting.
+S
-S
-R
Configure the Unit
To configure the unit, use the buttons on the controllerÕs
front panel.
Choices are: 4004, 4005, 4006,
4007, 4008, 4017, 4018 and 700.
¥
¥
¥
ac power
ᮡ
ᮣ
/MAX
SETPTS
/MIN
MENU
RESET
Sensor
1Ú8Ó flat blade screwdriver
4. Press MENU to store the value.
PANEL THICKNESS
6,4 (.25) MAX
0,8 (.03) MIN
To:
Take This Action
5. Press RESET twice to display the current
2-Wire Input (400 Series)
temperature.
Mount the Meter
1. Cut a panel opening
using the dimensions
shown to the right.
Display the
Configuration
Menu.
Press the MENU button.
The first function on the
menu, ÒINPTÓ, displays.
1,5
R(.06)
4 PLCS
45,00 + 0,61/-0,00
(1.772 + .024/Ð.000)
1
2
3
ᮡ
ᮣ
ᮡ
ᮣ
/MAX
/MAX
SETPTS
/MIN
MENU
RESET
SETPTS
/MIN
MENU
RESET
92,00 + 0,81/Ð0,00
(3.622 + .032/Ð.000)
Select the
submenu
function.
1. Press MENU until the
function you want is shown.
+S
-S
-R
2. Position the unit in the
opening, making sure
ᮣ
NOTE: Dimensions in Millimeters (Inches)
2. Press /MIN.
the front bezel is flush with the panel.
To Change the Decimal Point:
ᮡ
Select a value
for that submenu
function.
1. Press /MAX. to display
the option you want.
2. Press MENU to select it.
ÒSTRDÓ quickly flashes,
indicating that the selection
has been stored in memory.
Then the next menu function
displays.
1. Press MENU until the display
Connect ac Power
shows ÒDEC.PÓ:
Warning: Do not connect ac power to your meter
until you have completed all input and output
connections. Failure to do so may result in injury!
ᮡ
ᮣ
/MAX
SETPTS
SETPTS
SETPTS
/MIN
MENU
MENU
MENU
RESET
RESET
RESET
3-Wire Input (700 Series)
Hook up Alarm 1 (Setpoint) (refer to TB1 Main
ac Power Connection Drawing)
ᮣ
2. Press /MIN to show the current
1. Remove the panel at the back of the unit.
2. Locate the TB1 connector.
decimal point location:
Go back to the
previous menu
function.
Press RESET once.
1. Connect a jumper from ac Line (Terminal 7) to
Relay 1 Common (Terminal 3).
ᮡ
ᮣ
/MAX
/MIN
3. Insert the correct wire in each terminal as shown
in the following figure and tighten the lockdown
screws. Tug gently on the wires to verify
connections.
2. Connect Relay 1 Normally Open (Terminal 1) to
External Alarm ac Line.
Exit the
Configuration
Menu.
¥
¥
Press RESET twice. The
unit reinitializes (displays
ÒRSTÓ, then ÒTHERMISTORÓ).
When the temperature
displays, the meter is back in
Run Mode.
ᮡ
3. Press /MAX to select the setting.
VERSION #1
VERSION #2
Choices are: ÒFFF.FÓ, ÒFFFF.Ó or
ÒFF.FFÓ.
3. Connect External Alarm to ac Neutral (Terminal 8).
ᮡ
ᮣ
/MAX
/MIN
TB1
4. Press MENU to store the value.
Hook up Alarm 2 (Setpoint) (refer to TB1 Main
ac Power Connection Drawing)
1
2
3
4
5
6
1
2
3
4
5
6
TB2
5. Press RESET twice to display the current
1
2
3
7
8
9
10 11 12
1
2
3
7
8
9
Optionally, you can press
MENU to move through all
the menu functions until the
meter reinitializes.
temperature.
1. Connect a jumper from ac Line (Terminal 7) to
Relay 2 Common (Terminal 6).
EARTH
GROUND
NEUTRAL
LINE
2. Connect Relay 2 Normally Open (Terminal 4) to
External Alarm ac Line.
AC POWER
ᮡ
ᮣ
ᮡ
ᮣ
/MAX
/MAX
SETPTS
/MIN
MENU
RESET
SETPTS
/MIN
MENU
RESET
FUSE
3. Connect External Alarm to ac Neutral (Terminal 8).
Main ac Power Connections
Download from Www.Somanuals.com. All Manuals Search And Download.
|