°C
°F
+
Output
–
®
Thermo-
couple
Analog
Output,
1 mV per
degree
Input
OFF
Press
(SMP or OST
Connectors)
Low
Batt
Super MCJ
K
Thermocouple to
Analog connector
Super MCJ
SMCJ-J, SMCJ-K, SMCJ-T
INSTRUCTION
M2813-0103
For latest product manuals: omegamanual.info
SHEET
Thermocouple-to-Analog Connector
GENERAL DESCRIPTION
This is a Thermocouple to Analog Connector.
The input connection can be SMP or OST
both flash alternately once a second.
It converts a thermocouple input signal (Type
type connections. The output connection is
When the battery voltage drops below a
certain level, a red LED starts to flash once a
second. This is a low battery indication. The
battery must be replaced with a fresh battery
immediately.
J, K, or T) to a linear, compensated, amplified standard banana plug or jack. The plastic
®
analog output. The unit provides 1mV/°F or
1mV/°C analog output. The analog output
can go to a strip chart recorder or a digital
voltmeter for temperature monitoring.
case and the rubber gasket Bumper Band
provides a rugged and sealed connector
design. Figure 1 provides a functional flow
chart of how the unit operates. This unit is
operated using a single tactile feedback
Field Adjustments
The unit is powered by a single AA size
lithium battery. In order to install the battery,
remove the back cover and place the battery
on the PC board. The battery polarity is
indicated on the PC board. If the battery is
installed reverse, the unit will not power up.
The back cover is mounted to the front cover
via two mounting holes.
Press
The unit is field adjustable by removing the
button
.
back cover and accessing the three
There are 3 LEDs built into the connector.
The °C green LED flashes once every 2
seconds when the output provides 1mV/°C.
The °F green LED flashes once every 2
seconds when the output provides 1mV/°F. If
the input is open the °C and °F green LEDs
potentiometers. R17 provides offset
adjustment when the unit is in mV/°F mode.
R42 provides offset adjustment when the unit
is in mV/°C mode. R32 provides span (gain)
adjustment either in mV/°F or mV/°C mode.
OTHER IMPORTANT CONSIDERATIONS BEFORE OPERATION
CAUTION
SPECIFICATIONS
Measuring Temperature Range:
Type J: -100 to +750°C (-148 to +1382°F)
Type K: -100 to +1250°C (-148 to +2282°F)
Type T: -100 to +350°C (-148 to +662°F)
Accuracy @ 75°F ambient
for use with equipment (digital multimeter,
Follow all the safety precautions and
chart recorder, etc.) which have no accessible
operating instructions outlined in the manual.
live parts. Such equipment should comply with
all the applicable safety requirements.
The installation category is one (1).
temperature across the range:
Type J: 1.4°C ( 2.5°F)
There are no user replaceable fuse in
Do not open batteries, dispose of in fire,
this product.
Type K: 3°C ( 5°F)
heat above 100°C (212°F), expose contents to
Type T: 2°C ( 3°F)
water, recharge, put in backwards, mix with
used or other battery types. It may cause
explosion, leakage or personal injury.
Use cloth damped with warm water and
soap to clean the outside case and label. Do
not use flammable liquid solutions for cleaning.
Do not immerse the product in water.
Maximum input voltage to earth: 30
Vrms (42.4 peak) or 60 Vdc.
Avoid contact with hazardous live parts.
The thermocouple probe should not be
connected to hazardous live voltages (less than
max. input voltage to earth).
Input Connection: SMP or OST connector
Input Impedance: 3M-ohms
Output Connection: Standard Banana
Plug or Jack
Thermocouple Break Protection:
Output goes Upscale (std.)
The output terminals of this product are
°F & °C Green LEDs flash once a second
Output: 1mV/°F or 1mV/°C, °F or °C Green
LEDs flash once every 2 seconds
Output Load: 1K-Ohms min.
Power: One AA size Lithium Battery, 3.4 to
3.6 VDC 1900 mAH
°C
Press
Output Upscale/Downscale
°F
YES
1 sec Delay
NO
°C
Input
1mV/°C Mode
1mV/°C Output
°F
Open
Start
Battery Life @ 75°F Ambient Temperature:
1440 hours (60 Days), continuous, no load
Low Battery Indication:
Sleep
Press
Mode
°C
NO
Input
1mV/°F Output
°F
1mV/°F Mode
Red LED flashes once a second,
Response Time:
Open
YES
°C
°F
Press
(0 to 63% of Final value): 150 msec
Operating Temperature:
Output Upscale/Downscale
0 to 50°C (32 to 122°F)
Figure 1, Functional Flow Chart
Thermal Zero Drift: 0.05 mV/°C
(0.05 mV/°F) ambient temperature change
Operating Relative Humidity: 95% or
less, without condensation
Accessories
Model No.
OM-NOMAD-BATT
SMCJ-CAB
Description
Dimensions:
Replacement Battery
4"L x 2"W x 1"H (10L x 5W x 2.5H cm)
Weight: 2.4 oz (67g)
Cable Wire (Red & Black) 36" Long
Download from Www.Somanuals.com. All Manuals Search And Download.
|