MADE
IN
IN
WARRANTY/DISCLAIMER
USA
USA
5
6
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for a period of 13 months from date of
purchase. OMEGA Warranty adds an additional one (1) month grace period
to the normal one (1) year product warranty to cover handling and
shipping time. This ensures that OMEGAs customers receive maximum
coverage on each product.
9. Start the configuration program, you need to indicate which
serial port is to be used for serial communication by checking
the appropriate check box on the opening menu.
Power Input and Analog Output Setup:
To connect the signal input proceed as follows:
1. Connect a DC power supply with an output voltage
between 10 to 32 Volt DC to the signal conditioner (J1).
Note: If power supply used has current limiting, it may not
be able to power the signal conditioners if the available output
voltage is around 10 Volt, since the peak current may reach 1
to 5 Amp for a few milliseconds.
If the unit should malfunction, it must be returned to the factory for
evaluation. OMEGAs Customer Service Department will issue an Authorized
Return (AR) number immediately upon phone or written request. Upon
examination by OMEGA, if the unit is found to be defective it will be repaired
or replaced at no charge. OMEGA’S WARRANTY does not apply to defects
resulting from any action of the purchaser, including but not limited to
mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the
unit shows evidence of having been tampered with or shows evidence of
being damaged as a result of excessive corrosion; or current, heat, moisture
or vibration; improper specification; misapplication; misuse or other
operating conditions outside of OMEGAs control. Components which wear
are not warranted, including but not limited to contact points, fuses, and
triacs.
Note: It is not necessary to know the serial communication
protocol. i.e. baud rate, parity, 7/8 data bit and stop bit; the
program will determine this information automatically.
However, it is good practice to mark the protocols used on the
signal conditioner label if different from default.
2. Determine the maximum current to be measured.
3. Determine the appropriate input connection. i.e. 10 mA,
100 mA have the same input, 1 Amp and 5 Amps have
their own dedicated input. The return is common to all
inputs.
10. Once the program starts it will automatically detect the
signal conditioner configuration and will display a window of
available options. To view the signal input click on the
display on/off.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided
by OMEGA, either verbal or written. OMEGA warrants only that the
parts manufactured by it will be as specified and free of defects.
OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon which
liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
DRN-ACC
AC Current Signal Conditioner
11. To change analog output scaling choose analog output
scaling and enter the desired values.
4. Ensure that if the selected range is different from the default
(5A) then change the internal range by using the Setup
Software and select the appropriate range.
12. Once the custom scaling is finished, ensure that Send
Configuration is clicked, otherwise the changes will not take
effect.
®
®
5. Connect the signal input to screw terminal, and ensure that
the screws are tight. Failure to do so may cause electrical
shock should the wires become loose and come out of the
screw terminal.
OMEGAnet¨ On-Line Service
Internet e-mail
13. The input/output scaling may be fine tuned, while both
communication and analog output are active. You may make
a change to the analog output in the configuration program,
and watch the DVM connected to analog output of the signal
conditioner follow the new settings.
Servicing North America:
6. To verify that the set up is correct, you may connect a DVM
to the analog output. Once connected, power the signal
conditioner and apply a known current from an AC source to
input. Measure and compare with expected values. To
custom scale the analog output proceed to the next step.
7. To view/change the scaling that relates the analog output to
signal input: connect the RS232 output of the signal
conditioner to an available serial port of a computer. The
cable and the DB9 or DB25 connectors are available as an
option.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it
be used: (1) as a Basic Component under 10 CFR 21 (NRC), used in or with any
nuclear installation or activity; or (2) in medical applications or used on humans.
Should any Product(s) be used in or with any nuclear installation or activity,
medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY / DISCLAIMER language,
and additionally, purchaser will indemnify OMEGA and hold OMEGA harmless
from any liability or damage whatsoever arising out of the use of the Product(s)
in such a manner.
USA:••
ISO 9001 Certified•
••
••
One Omega Drive, P.O. Box 4047
Stamford CT 06907-0047
TEL: (203) 359-1660••
FAX: (203) 359-7700
FAX: (514) 856-6886
14. You may save or print a particular configuration by
selecting the file menu. ItÕs always a good practice to both
print and save the scaling of each signal conditioner.
15. If the program is not able to establish communication then
an error message is displayed. This happens either when the
wrong serial port is specified or when the cable is
disconnected.
e-mail: [email protected]
Canada:••
976 Bergar
••
••
••
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928••
e-mail: [email protected]
For immediate technical or application assistance:
RETURN REQUESTS / INQUIRIES
USA and Canada:•
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA¨
Customer Service: 1-800-622-2378 / 1-800-622-BEST¨
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN¨
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Direct all warranty and repair requests/inquiries to the OMEGA Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM
OMEGA S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
••
••
••
Mexico and •
Latin American:•
••
TEL: (001)800-TC-OMEGA¨•
En Espa–ol: (001) 203-359-7803•
e-mail: [email protected]
FAX: (001) 203-359-7807
8. Turn on the computer, start Windows 3.0 or higher and run
the Signal Conditioner Configuration Setup Program. If the
program has not been installed, then insert the 3.5Ó floppy
disk in either drive A or B. From the Program Manager
choose File, Run; in the command box type either A: setup or
B: setup according to your drive designation. The program
will create an icon for the signal conditioner. You may start
the program by clicking on this icon.
The purchaser is responsible for shipping charges, freight, insurance and
proper packaging to prevent breakage in transit.
Servicing Europe:
Benelux:••
Postbus 8034, 1180 LA Amstelveen, The Netherlands
TEL: +31 20 3472121•• FAX: +31 20 6434643
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
FOR WARRANTY RETURNS, please
have the following information
available BEFORE
••
••
••
Toll Free in Benelux: 0800 0993344•
e-mail: [email protected]
contacting OMEGA:
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its
products to the European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification.
Czech Republic:•
••
••
RudŽ arm‡dy 1868, 733 01 Karvin‡ 8
TEL: +420 69 6311899• FAX: +420 69 6311114
e-mail: [email protected]
1. P.O. number under which the
product was PURCHASED,
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
1. P.O. number to cover the COST of
the repair,
2. Model and serial number of
product, and
3. Repair instructions and/or specific
problems relative to the product.
France:••
••
••
9, rue Denis Papin, 78190 Trappes
TEL: +33 130 621 400• FAX: +33 130 699 120
Toll Free in France: 0800406342
e-mail: [email protected]
The information contained in this document is believed to be correct but
OMEGA Engineering, Inc. accepts no liability for any errors it contains, and
reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.
••
Germany/Austria:•
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0• FAX: +49 7056 9398-29
Toll Free in Germany: 0800 TC-OMEGA¨
e-mail: [email protected]
OMEGAs policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology
and engineering.
••
••
••
PATENT AND TRADEMARK NOTICE: This product is covered by one
or more of the following patents: U.S. Pat. No. Des. 336,895,
5,274,577/ Canada 2052599, 2052600/ Italy 1249456, 1250938/
France Brevet No. 91 12756/ Spain 2039150, 2048066/ UK Patent
No. GB2 249 837, GB2 248 954/ Germany DE 41 34398 C2.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
United Kingdom:•
ISO 9002 Certified•
••
••
••
••
One Omega Drive
River Bend Technology Centre
Northbank, Irlam Manchester M44 5EX United Kingdom
TEL: +44 161 777 6611• FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: [email protected]
'
Copyright 2001 OMEGA ENGINEERING, INC. All rights reserved.
This device is marked with the international hazard symbol.
It is important to read the Setup Guide before installing or
commissioning this device as it contains important
information relating to safety and EMC.
This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in
part, without prior written consent of OMEGA ENGINEERING, INC.
®
®
omega.com
,
are trademarks of OMEGA Engineering, Inc.
M2522/0201
Download from Www.Somanuals.com. All Manuals Search And Download.
|