INSTRUCTION
MANUAL
Eat well, drink well and live well with Omega
VRT400 SERIES
Product Contents
OMEGA PRODUCTS, INC.
6291 LYSTER LANE
HARRISBURG, PA 17111-4523 U.S.A.
PHONE: 1.800.633.3401
FAX: 717.561.1298
English, May 3013
May 2013
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
Download from Www.Somanuals.com. All Manuals Search And Download.
With the Omega Slow Squeezing System and Juice Cap mixing
feauture, you can easily make personalized juice rich in taste,
flavor and full of valuable nutrients.
Omega Juicer Manual For Household Use
(Warranty Included)
1. Read “Precautions for safe use (Page 4)” carefully and use
the appliance properly.
1. More Nutrients andTaste:Your own personalized juice
2. Save these instructions.
Mixed juice
Enjoy single ingredient juice or mixed juice.
Add various ingredients to your taste and health.
3. Check if the voltage indicated on the base of the appliance
corresponds to the local voltage before you connect
the appliance.
Alternative Meal
Make juice as an alternative meal, rich in taste
and balanced nutrients.
CONTENTS
Dear Omega Customers__________________________________ 1
General description and parts names ______________________ 2
Specific terms for parts___________________________________ 3
Precautions for safe use __________________________________ 4
Warnings and cautions ___________________________________ 5
Slow Juicer assembly ____________________________________ 8
Slow Juicer assembly in detail_____________________________ 9
How to use the appliance_________________________________ 10
Juice Cap and Extraction Packing _________________________ 11
When the Screw is stopped during operation________________ 12
(How to use [Reverse/REV] button)
Important safeguards in use ______________________________ 13
Disassembly, cleaning and care ___________________________ 14
Bowl disassembly and wash ______________________________ 16
Sterilization and Easy Cleaning System_____________________ 17
Spinning Brush disassembly and wash_____________________ 18
Spinning Brush assembly_________________________________ 19
Bowl Packing assembly __________________________________ 20
Juice Cap Packing assembly______________________________ 21
Troubleshooting _________________________________________ 22
Appliance specifications__________________________________ 23
Baby Food
Make baby food by mixing meat, grain and vegetables for
various growth phases.
Soybean milk and soy juice
While the juice cap is closed, adjust the proportion of boiled
beans and water to easily make soybean milk and soy juice
to your desired consistency and concentration.
2. More Convenient and User Friendly
Open and close the none drip juice cap to adjust the amount
of juice desired.
3. More Advanced Easy Cleaning System (Page 17)
The juice cap makes clean-up easy! Fill the bowl with water
and operate the appliance for easy washing.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL DESCRIPTION AND PARTS NAMES
SPECIFIC TERMS FOR PARTS
<FRONT>
<BACK>
HOPPER
PULP CONTAINER
SQUEEZING SCREW
4. Hopper
rear part
1. Hopper front
triangle
2. Bowl triangle
JUICE CONTAINER
5. Operating
switch
COARSE STRAINER
(OPTIONAL)
6. Juice outlet
3. Pulp outlet
7. Juice cap
8. Power cord
FINE STRAINER
CLEANING BRUSH
SPINNING BRUSH
9. Grip
STRAINER*
SMALL CLEANING BRUSH
COARSE STRAINER (Optional)
BOWL
The bigger holes in the strainer produce thicker juice when tender and soft fruits are extracted such as
strawberries, kiwis and tomatoes.
FINE STRAINER
The holes of the strainer are small. Use it when making pure juice with hard fruits,
beans or higher fibered vegetables.
BASE
PUSHER
1 pusher, 1 hopper, 1 screw, 1 fine strainer, 1 coarse strainer (Optional), 1 spinning brush,1 bowl
1 base, 1 juice container, 1 pulp container, 1 small cleaning brush, 1 cleaning brush, 1 manual
NUMBER OF
ATTACHMENTS
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS FOR SAFE USE
WARNINGS AND CAUTIONS
WARNING
Hazards or unsafe practices which could result in serious personal injury or death.
WARNING Hazards or unsafe practices which could result in serious personal injury or death.
CAUTION Hazards or unsafe practices which could result in minor personal injury or appliance damage.
DO NOT PLUG IN OR UNPLUG WITH WET HANDS.
It may cause an electric shock or an injury.
DO NOT USE WITH OTHER THAN RATED VOLTAGE.
It may cause an electric shock, a fire or abnormal performance.
It the voltage is diffirent, it may shorten the life of the motor or cause a failure.
SIGN EXAMPLES
PLUG THE POWER CORD CORRECTLY AND PUSH IT TIGHT IN A WALL SOCKET.
It may cause an electric shock or a fire.
The sign indicates contents that may cause risk of a fire or an electrical shock.
Specific warnings are written in the sign.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE
MANUFACTURER, ITS SERVICE OR SIMILARLY QUALIFIED PERSONS
IN ORDER TO AVOID A HAZARD.
The sign indicates contents that may cause risk of a fire or an electrical shock.
Specific warning are written in the sign.
If the power cord is damaged, it may cause an electric shock or fire.
NEVER ALTER THE APPLIANCE. ALSO, DO NOT DISASSEMBLE OR REPAIR BY
YOURSELF. DO NOT INSERT FINGERS, FOREIGN SUBSTANCES OR OBJECTS
SUCH AS PINS INTO GAPS OR HOLES IN THE BASE.
The sign indicates prohibited acts.
Specific prohibitions are written around or in the sign.
It may cause a fire, an electric shock or a failure.
For any technical support, contact the authotized local Customer Care Center.
The sign indicates contents of regulating or directing actions.
Specific intructions are written around or in the sign.
DO NOT MOISTEN THE BASE OR SPLASH WATER ON THE BASE.
Be careful not to let any liquids or other substances get into the switch on the appliance.
DO NOT OPERATE THE SWITCH WITH WET HANDS.
It may cause an electric shock or fire.
WHEN THE POWER CORD, WIRE IS BROKEN OR DAMAGED OR THE PLUG-IN
PART BECOMES LOOSE, DO NOT OPERATE IT.
It may cause an electric shock, a fire or an injury.
FOR SAFETY, MUST DO GROUND CONNECTION. DO NOT DO THE
GROUNDING ON GAS PIPE, PLASTIC WATER PIPE, TELEPHONE WIRE, ETC.
It could cause an electric shock, a fire, a malfunction and an explosion.
Be sure to use the socket with ground connection.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS AND CAUTIONS
WARNINGS AND CAUTIONS
NEVER DISASSEMBLE BOWL SET DURING OPERATION OR
INSERT FINGERS, FOREIGN OBJECTS SUCH AS FORKS, SPOONS ETC.
INTO FEEDING TUBE OR JUICE OUTLET.
WHEN USING THE APPLIANCE, BE CAREFUL FOR A NECKTIE, LONG NECKLACE,
SCARF ETC. NOT TO BE ENTANGLED INTO FEEDING TUBE.
It may cause an injury, a failure or a breakage.
It may cause an injury, an accident or a failure.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING
CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN
SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE BY
A PERSON RESPONSIBLE FOR THEIR SAFETY.
PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE.
It may cause an injury or a failure.
Children should be supervised to ensure that they do not play with the appliance.
DO NOT OPERATE THE APPLIANCE FOR MORE THAN 30 MINUTES AT A TIME.
It may cause a motor failure due to overheating.
Cool it down sufficiently for 5 minutes and operate it again.
CAUTION
Hazards or unsafe practices which could result in minor personal injury or
appliance damage.
WHEN PLACING INGREDIENTS INTO THE FEEDING TUBE, ONLY USE THE
PUSHER PROVIDED.
It may cause an injury or a failure.
DO NOT OPERATE WITHOUT LOCKING THE HOPPER PROPERLY.
It may cause an injury or a failure.
DO NOT ALLOW A SEVERE SHOCK TO THE APPLIANCE OR DROP IT.
It may cause an electric shock, a fire or damage.
WHEN DETECTING A GAS LEAK, DO NOT INSERT THE POWER CORD INTO ITS
SLOT. OPEN THE WINDOW TO VENTILATE FULLY AND IMMEDIATELY.
IF THE APPLIANCE GIVES OFF AN UNPLEASANT SMELL OR EXCESSIVE
HEATING, SMOKE, STOP USING IMMEDIATELY AND CONTACT THE LOCAL
CUSTOMER CARE CENTER.
It may cause an injury or a failure.
When using a new appliance, it gives off a smell and the smell disapears naturally over time.
NEVER PUT A FINGER, A FORK OR A SPOON ETC. INTO JUICE OUTLET.
It may cause an injury or a failure.
ALWAYS UNPLUG THE APPLIANCE AFTER USE.
WHEN UNPLUGGING THE POWER CORD, MAKE SURE TO HOLD THE POWER CORD.
If holding the wire to unplug, it may cause an electric shock or a fire.
IF SCREW ROTATION IS STOPPED IN NORMAL OPERATION, PRESS [REVERSE/REV]
BUTTON AND HOLD FOR 2~3 SECONDS AND THEN AFTER REVERSE OPERATION
IS COMPLETELY STOPPED, PRESS [ON] BUTTON AGAIN.
If such a stop event continues duringthe operation, the parts may be damaged and
performance may be deteriorated due to overheating in a motor. When the problem
continues, immediatly stop the appliance and contact the local Customer Care Center.
DO NOT WASH AT HIGH TEMPERATURES OF 800C (1760F) OR MORE.
DO NOT PUT THE APPLIANCE IN A DISHWASHER, A DRYER OR A MICROWAVE ETC.
It may cause a failure or parts deformation.
THE APPLIANCE WEIGHS ABOUT 6KG (13.2LB).
DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE,
DISASSEMBLE THE BOWL SET OR PARTS AND TRY TO LOCK THEM.
It may cause an injury or a failure.
Any act of event needed, switch off first and unplug the power cord.
WHEN MOVING THE APPLIANCE, ENSURE TO MOVE IT HOLDING GRIPS TIGHTLY
AT THE BASE BOTTOM WITH BOTH HANDS.
If attempting to hold bowl or the edge of the base, the base falls causing an injury
or a failure.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SLOW JUICER ASSEMBLY
SLOW JUICER ASSEMBLY IN DETAIL
Align the hopper rear part with base completely as in below.
4 The hopper will not close properly when the parts are not assembled correctly.
Align hopper front triangle with [ ] bowl triangle
OPEN] first and turn it to clockwise until it
[
clicks so that the hopper triangle [ ] aligned
with bowl triangle [Close ].
Hopper
rear part
Assemble the parts in the order of bowl>spinning brush>strainer>squeezing screw>hopper
(or assemble the spinning brush into the bowl then fit strainer bump in the bowl inner groove).
Make sure all the triangles of bowl [ OPEN], strainer [ ] and hopper [ ] are aligned in a vertical line.
2,3
Make sure to press the screw down into the
strainer as in STEP 2. The hopper does not close
properly when the screw does not fit in completely.
Strainer
BOTTOM
OF THE
STRAINER
bump
Hopper
Squeezing Screw
Strainer
INSIDE THE
BOWL
Bowl inner
groove
Spinning brush
Bowl
Assemble the parts as following order :
Bowl>Spinning Brush>Strainer. Make sure bowl
triangle [ OPEN] aligns with strainer triangle [ ].
Op en
A spinning brush can be assembled regardless
of the direction.
Insert extraction packing at the bottom of the bowl hard enough into the pulp outlet.
1 Make sure bowl outer groove aligns with base bump completely
Base bump
Place the bowl in the base.
Extraction
packing
Bowl outer groove
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE APPLIANCE
JUICE CAP AND EXTRACTION PACKING
JUICE CAP
This is the cap of juice outlet in the bowl.
BACK VIEW
Close the juice cap and fill up with juice in the bowl with various ingredients. You can easily make mixed juices.
Juice cap
Close juice cap and press [ON] button to start.
When juice starts filling up the bowl, you can
mix banana, nuts, boiled sweet potato etc.
and liquids such as milk etc. as well as vegetables
and fruits like smoothies.
Wash the fruits and/or vegetables and cut
them in to pieces that fit in to the feeding
tube. Place the suitable pieces into feeding
tube slowly and press with a pusher.
Use fresh fruits and vegetables for juicing
as they contain more juice.
Juice cap
Open juice cap to pour out as much juice as you want.
Close juice cap without any drops.
Juice cap
packing
OPERATING Normal
Normal
OPERATING
SWITCHES
direction
SWITCHES
direction
EXTRACTION PACKING
This is the pulp stopper made of silicone at the bottom of the bowl. Make sure to close extraction packing always as shown below
before use. For cleaning, let extraction packing open and start washing. (Page 16)
Normal
Normal
Press
direction
direction
off (stop)
Stop
STOP status
Reverse
direction
CLOSED
Reverse
direction
Reverse
direction
Reverse
direction
After juicing is completed, click
[Reverse/ REV] to stop.
Press [On] button to start.
Motor does not stop immediately when
clicking [Reverse/REV]. It stops slowly for
safety and performance reasons.
Extraction
packing
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEN THE SCREW IS STOPPED DURING OPERATION
(REVERSE/REV BUTTON)
IMPORTANT SAFEGUARDS IN USE
• Fruits with pits, hard seeds such as nectarines, peaches, mangos, apricots,
plums and cherries must be pitted before juicing.
Click [Reverse/REV] button and stop
the appliance.
• Cut fibrous ingredients (water parsley setc.) in small size like 3~4cm (1.5inch)
and place to the feeding tube
• Drink the fruit juice or green vegetable juice immediately after you have extracted.
If it is exposed to air for a period of time, the juice will lose its taste and natural value.
• Do not use the appliance for grinding dry ingredients such as grains, coffee beans, etc.
It may cause a part damage or a failure.
Stop
• Do not re-squeeze the pulp in the pulp outlet.
• Do not operate the appliance when the bowl is empty.
DO NOT USE IT FOR MORE THAN 30 MINUTES CONTINUOUSLY.
It may cause a failure due to overheating in a motor.
When using continuously, stop and cool it down for 5 minutes in between each
30 minute use.
Press [Reverse/REV] button in operating
switches for 3~5 seconds and release it.
Repeat this process 2~3 times.
NEVER INSERT A FINGER, A FORK OR A SPOON, ETC. INTO JUICE OUTLET
DURING OPERATION.
It may cause damage to parts.
Reverse is the button pushing ingredients
upward. Reverse only works while the button
is pressed and held. Once button is released,
screw rotation stops.
ONLY USE THE PUSHER TO PRESS DOWN THE INGREDIENTS.
If using other object, it may cause damage to parts, an injury or a failure.
Reverse
direction
(REV)
DO NOT PLACE GRAINS, FRUIT WITH HARD SEED OR NUTS WITH HARD
SHELL SUCH AS WALNUTS.
It may cause damage or a failure of bowl, screw, squeezing strainer, etc.
Fruits with pits,hard seeds such as nectarines, peaches,mangos, apricots, plums and
cherries must be pitted before.
After the rotation stops completely,
press [ON] button to operate.
Normal
direction
(ON)
Any direction you want to change from either
Normal direction or Reverse direction, make
sure that screw rotation is stopped completely.
Then operate any button you needs.
DO NOT OPERATE SWITCHES WITH WET HANDS.
It may cause an electric shock, an electric leakage or a fire.
Do not leave any foreign substances around switches.
DO NOT JUICE SEAFOOD AND MEAT.
It may cause abnormal performances or a failure.
NOTE
If the screw does not work even after the above
process, unplug the power cord from the socket,
disassemble the bowl set, wash and use it again
DO NOT JUICE FRUIT PRESERVED IN SUGAR, HONEY, ALCOHOL, ETC .
(GRAPES, APRICOT, BERRIES, ETC.).
Frozen fruit or withered ingredients stored in the refrigerator for a long time may produce less juice
or no juice at all.
NOTE
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY, CLEANING AND CARE
DISASSEMBLY, CLEANING AND CARE
FIGURE IN ORDER
1. Ensure the motor stops completely and unplug the power cord.
When unplugging the power cord, hold the head part of the power cord and unplug it.
Do not touch the power cord with wet hands.
2. Hold the juice outlet and the hopper with both hands and lift them up from the base.
3. Disassemble the parts as below:
1) Unlock the bowl twisting to counterclockwise.
2) Take the screw out.
Juice outlet
3) Remove the strainer.
4) Take the spinning brush out and disassemble the silicone brush.
4. Rinse each parts with cleaning brush. Brush the inside and outside under running water.
Never use scouring pads, abrasive cleaning agent aggressive liquids or sharp cleaning tools.
Do not wash them in a dishwasher or a dish dryer.
5. Wipe the stain on the base with soft damp cloth or wrung towel and dry the base thoroughly.
Do not immerse the base unit in water or any other liquid nor rinse, it under tap.
6. After each cleaning ,allow parts to air-dry completely and store in a clean and safe place.
Always wash the bowl set immediately after each use. If you skip this step, pulp may dry up and stick to the bowl set.
making it difficult to disassemble or wash. It may also cause degradation in performance.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BOWL DISASSEMBLY AND WASH
STERILIZATION AND EASY CLEANING SYSTEM
STERILIZATION
Juice cap
packing
bowl packing
Remove Juice Cap packing and bowl packing.
1
For sterilization, use baking soda or natural wash-up liquids only.
Open juice cap first. Hold the bowl and juice cap with one hand and remove juice cap packing with the other hand.
When removing it, be careful not to drop the juice cap and bowl. It may cause damage to the juice cap.
Remove the bowl packing by pinching and twisting it with two fingers.
You can thoroughly wash parts by immersing in water diluted with one or two drops of baking soda
or natural wash-up liquids for about 30 minutes.
EASY CLEANING SYSTEM
Extraction
packing
Open the extraction packing at
Wash the bowl and all the packings.
the bottom of the bowl
2
3
After closing the juice cap, pour the water
into feeding tube and operate the appliance.
After a while, open the juice cap
and discharge the water.
1
2
Wash bowl and bowl packing with cleaning
brush under the running water.
Whenever changing the ingredient, it is not necessary to disassemble and wash the bowl.
After juicing, make sure to disassemble and wash the bowl set.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINNING BRUSH DISASSEMBLY AND WASH
SPINNING BRUSH ASSEMBLY
Remove the spinning brush
from strainer.
SPINNING BRUSH
SILICONE BRUSH
Inner
Check the groove of the spinning brush
and the direction of silicone brush.
wing
There are grooves to insert silicone brush in
the spinning brush.
Silicone brush has inner wing
and outer wing.
UP
(longer part)
As shown to the left, let ‘inner wing’ face
the spinning brush.
Outer wing
Brush
groove
Down
(shorter part)
Detach the silicone brush from
spinning brush.
Insert the silicone brush into
the spinning brush.
Spinning brush
Silicone brush
As shown to the left, hold the outer part of
silicone brush with your fingers an pull it out
to the arrow direction. It is recommended
to remove it according to the above method.
If pulling it by force, silicone brush may be
torn or spinning brush may be damaged.
According to the N o.1 above, let the longer
part of inner wing
face upward.
Hold the outer wing
of silicone brush
with your thumb and index finger and
insert the inner wing into the groove
of spinning brush.
With cleaning brush, wash inside and
outside of spinning brush like brushing
under the running water.
Pull the inner wing tight enough.
Push silicone brush from the outer side
of spinning brush and pull ‘inner wing’ in
the direction of inside of the spinning brush
with the other hand as shown to the left.
Wash silicone brush in the same way under
the running water.
Hold the outer wing of silicone brush
Pull it until you cannot pull it any longer.
If units are operating without fully assembled,
there is a risk of breakage.
Hold up and down of ‘outer wing’ and pull
it tight enough.
Cleaning brush
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BOWL PACKING ASSEMBLY
JUICE CAP PACKING ASSEMBLY
Hold the bowl packing like pinching.
Hold juice cap packing as shown
to the left.
As shown to the left in a dotted circle,
let the protrusion part on the bowl packing
face upward and hold it like pinching with
your thumb and index finger.
As shown to the left in a dotted circle,
the hole must be visible when you hold.
Bowl
packing
Juice cap packing
Insert the bowl packing into the
bowl hole.
Open the juice cap and insert the juice
cap packing in.
Insert the bottom of the bowl packing
into the bowl hole and fully press it down.
Do not insert whole part of bowl packing.
The upper part of the bowl packing must
be shown.
Insert it in from the top to the juice cap.
Be careful not to drop the bowl.
Organize the packing to seal
off completely.
Turn over the bowl and organize the
bowl packing in place.
If the packing is not completely sealed,
it may cause juice leaking.
If the bowl packing at the bottom of the bowl
is not fully inserted and bent, organize it with
the rotating attractor of the cleaning brush.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
APPLIANCE SPECIFICATIONS
Check the details below before contacting Technical Support for repair or service.
If you need information or if you have a problem, please contact the local Customer Care Center.
When applying for after sales service, check the manufacturer’s serial number or bar code.
APPLIANCE STANDARDS
THE APPLIANCE DOES NOT WORK.
Make sure the power cord is properly plugged in.
Check the hopper is assembled properly. If the hopper has not been properly locked in place, the appliance does not work for safety reasons.
Check if the appliance has been assembled according to the manual in an ordinary manner.
See the assembly in the manual or consult with the local Customer Care Center for help.
PRODUCT NAME
MODEL NAME
Omega Slow Squeeze Juicer
VR T400 Series
120 V
THE HOPPER DOES NOT OPEN.
RATED VOLTAGE
Is there alot of pulp left inside the bowl? Press [ON] button to discharge internal pulp.
Have you placed any foreign substances or solid objects such as hard seeds?
Press the [Reverse/REV] button to make foreign substances come up again toward the feeding tube.
RATED FREQUENCY 60 Hz
Do not attempt to open it by force or with too much pressure. Still it does not work following by the above process,
contact the local Customer Care Center.
RATED POWER
CONSUMPTION
150 W
IT STOPS DURING NORMAL OPERATION.
Have you put heavy loads of ingredient or a thick/big ingredient? Read the manual Page 12 and follow Reverse/REV button guideline
Still the problem has not been solved, contact the local Customer Care Center.
RPM (REVOLUTIONS
PER MINUTE)
80 RPM
1.4 m
THERE ARE GATE MARKS (FORMING MARK) RESULTING FROM THE MOLDING PROCESS.
It is normal, and there is no problem for use.
CORD LENGTH
MOTOR
Single-phase
induction motor
WHAT IS THE DIFFERENCE BETWEEN FINE STRAINER AND COARSE STRAINER?
Regarding strainer selection for suitable ingredients, read the manual Page 3.
FUSE
250 V 10 A
JUICE LEAKS OVER THE BASE.
Is Extraction packing properly inserted in?
OUT WARD
DIMENSIONS
Width 160 MM
Length 218 mm
Height 405 mm
Juice could leak when the extraction packing is not properly inserted. Please push the extraction packing tight enough.
Juice is still leaking even though the extraction packing was inserted properly?
If an amount of input ingredient is too much compared to the size of pulp outlet, the packing may be slightly pushed out and
juice may leak through the gap. Do not process heavy loads at a time; squeeze little by little.
RATED
OPERATING TIME
LESS THAN 30 MINUTES
THE BOWL SHAKES WHEN SQUEEZING.
Slight shaking may be occurred due to motor movement.
Large or small movements occur depending on the pulp texture of ingredients (hard or tough).
It is normal when the screw is rotating. Please note that it is not malfunction.
Hard ingredients (e.g:carrots/potatoes/radishes/beetroots etc.) may shake the bowl more than soft and juicy ingredient.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|