OMEGAPHONE®
OMA-P1104
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Your OMA-P1104 has been carefully designed to give you
years of safe, reliable performance. As with all electrical
equipment, however, there are a few basic precautions you
should take to avoid hurting yourself or damaging the unit:
• Read the installation and operating instructions in this
manual carefully. Be sure to save it for future reference.
• Read and follow all warning and instruction labels on
the product itself.
• To protect the OMA-P1104 from overheating, make sure
all openings on the unit are not blocked. Do not place on
or near a heat source, such as a radiator or heat register.
• Do not use your OMA-P1104 near water, or spill liquid
of any kind into it.
• Be certain that your power source matches the rating
listed on the AC power transformer. If you’re not sure of
the type of power supply to your facility, consult your
dealer or local power company.
• Do not allow anything to rest on the power cord. Do not
locate this product where the cord will be abused by
persons walking on it.
• Do not overload wall outlets and extension cords, as this
can result in the risk of fire or electric shock.
• Never push objects of any kind into this product through
ventilation holes as they may touch dangerous voltage
points or short out parts that could result in a risk of fire
or electric shock.
• To reduce the risk of electric shock, do not disassemble
this product, but return it to Omega Customer Service,
or other approved repair facility, when any service or
repair work is required. Opening or removing covers
may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock when the
unit is subsequently used.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
• If anything happens that indicates that your OMA-P1104
is not working properly or has been damaged, unplug it
immediately and follow the procedures in Appendix C
for having it serviced. Return the unit for servicing
under the following conditions:
1. The power cord or plug is frayed or damaged.
2. Liquid has been spilled into the product or it has been
exposed to water.
3. The unit has been dropped, or the cabinet is damaged.
4. The unit doesn’t function normally when you’re
following the operating instructions.
• Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of
electric shock from lightning.
• Do not use the telephone to report a gas leak in the
vicinity of the leak.
CAUTION
To Reduce the Risk of Fire or Injury to Persons, Read and
Follow these Instructions:
1. Use only the following type and size batteries:
Alkaline, size D.
2. Do not dispose of the batteries in a fire. The cell may
explode. Check with local codes for possible special
disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte
is corrosive and may cause damage to the eyes or skin. It
may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the
battery with conducting materials such as rings, bracelets,
and keys. The battery or conductor may overheat and
cause burns.
5. Do not mix old and new batteries in this product.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Requirements
Part 68: The OMEGAPHONE® OMA-P1104 complies with
Part 68 of the FCC rules. On the back of the unit there is a label
that contains, among other information, the FCC Registration
Number and the Ringer Equivalence Number (REN) for this
equipment. You must, upon request, provide this information to
your local telephone company.
The REN is useful to determine the quantity of devices that you
may connect to your telephone line and still have all of those
devices ring when your telephone number is called. In most, but
not all areas, the sum of the REN’s of all devices connected to
one line should not exceed five (5.0). To be certain of the
number of devices that you may connect to your line, you may
want to contact your local telephone company to determine the
maximum REN for your calling area.
This equipment may not be used on coin service provided by
the telephone company. Connection to party lines is subject to
state tariffs.
Should the OMA-P1104 cause harm to the telephone network,
the telephone company may discontinue your service tempo-
rarily. If possible, they will notify you in advance. But if
advance notice isn’t practical, the telephone company may
temporarily discontinue service without notice and you will be
notified as soon as possible. You will be informed of your right
to file a complaint with the FCC. The telephone company may
make changes in its facilities, equipment, operations, or
procedures where such action is reasonably required in the
operation of its business and is not inconsistent with the rules
and regulations of the FCC that could affect the proper func-
tioning of your equipment. If they do, you will be notified in
advance to give you an opportunity to maintain uninterrupted
telephone service.
If you experience trouble with this equipment, or you need
information on obtaining service or repairs, please contact:
OMEGA Customer Service
1-800-622-2378 (1-800-622-BEST)
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
The telephone company may ask that you disconnect this
equipment from the network until the problem has been
corrected or until you are sure that the equipment is not
malfunctioning.
Part 15: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits a designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
OMEGAPHONE® is a registered trademark of Omega
Touch Tone™ is a registered trademark of AT&T.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian Department of Communications Statement
Notice: The Canadian Department of Communications label
identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protec-
tive operational and safety requirements. The Department does
not guarantee the equipment will operate to the user’s satisfac-
tion.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some
cases, where the company’s inside wiring is associated with a
single line, individual service may be extended by means of a
certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an autho-
rized Canadian maintenance facility designated by the supplier.
Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspec-
tion authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device
denotes the percentage of the total load to be connected to a
telephone loop which is used by the device to prevent overload-
ing. The termination on loop may consist of any combination of
devices subject only to the requirement that the total of the
Load Numbers of all the devices does not exceed 100. For the
Omegaphone® OMA-P1104, the Load Number is 8.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS ......................... i
FCC Requirements ......................................................... iii
Canadian Department of Communications Statement ... v
Chapter 1: Introduction................................................. 1
Technical Support ..................................................... 2
Chapter 2: Installation................................................... 3
2.1 Operating Environment...................................... 3
2.2 Mounting ............................................................. 3
2.3 Power Surge Protection ..................................... 4
2.4 Power Supply and Battery Backup ................... 4
2.5 Starting the OMA-P1104 .................................... 5
2.6 Run Mode and Standby Mode ........................... 5
2.7 Telephone Line.................................................... 6
2.8 The Microphone .................................................. 7
2.9 Alert Inputs ......................................................... 8
2.10 Installing the Sensor ......................................... 9
2.11 Multiple Sensors.............................................. 11
2.12 Outdoor Wiring ................................................ 12
2.13 Disconnecting for Storage or Seasonal Use. .. 13
Chapter 3: Quick Start ................................................ 15
3.1 The Local Keypad ............................................. 15
3.2 Preparation for Programming ......................... 16
3.3 Quick-Start Programming Steps
Step 1: Set Configuration of Inputs .............................. 16
Step 2: Set the ID Number ........................................... 17
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
Step 3: Set Dial-Out Telephone Numbers .................... 18
Step 4: Set Temperature Limits .................................... 19
3.4
Summary of the Alarm Dial-Out Process .. 21
Chapter 4: Communications Programming .............. 23
4.1 The Unit ID Number ............................................... 23
4.1.1 Programming the ID Number .............................. 24
4.1.2 Interrogating the ID Number ............................... 24
4.2 Dial-out Telephone Numbers ........................... 25
4.2.1 Programming Dial-out Telephone Numbers ........ 25
4.2.2 Interrogating a Dial-out Telephone Number ........ 26
4.2.3 Erasing a Telephone Number.............................. 26
4.3 Tone or Pulse Dialing ...................................... 27
4.4 Special Dialing .................................................. 27
4.4.1 Special Dialing Keys ........................................... 28
4.4.2 Incorporating a Pause ......................................... 29
4.4.3 Incorporating a Pound (#) or Asterisk (*) ............ 30
4.4.4 Special Dialing to a Beeper or Pager .................. 31
4.5 Rings Until Answer .......................................... 33
4.5.1 Programming Rings Until Answer ....................... 33
4.5.2 Interrogating Rings Until Answer......................... 34
4.6 TAD (Telephone Answering Device).............. 34
4.6.1 TAD Enable/Disable ........................................... 35
4.6.2 Using the TAD Feature ........................................ 35
4.6.3 No TAD In Use .................................................... 36
4.7 Listen-in Time ................................................... 36
4.7.1 Programming the Listen-in Time ......................... 37
4.7.2 Interrogating the Listen-in Time .......................... 38
4.8 Call Delay .......................................................... 38
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8.1 Programming the Call Delay ............................... 38
4.8.2 Interrogating Call Delay....................................... 39
4.9 Local Voice Mute............................................... 40
4.9.1 Enable/Disable Local Voice Mute ........................ 40
4.10 Voice Repetitions ............................................ 40
4.10.1 Programming Voice Repetitions ........................ 41
4.10.2 Interrogating Voice Repetitions ......................... 41
4.11 Intercall Time................................................... 42
4.11.1 Programming Intercall Time .............................. 42
4.11.2 Interrogating Intercall Time ............................... 43
4.12 Maximum Number of Calls (Max Calls) ........ 43
4.12.1 Programming Max Calls.................................... 44
4.12.2 Interrogating Max Calls ..................................... 45
4.13 The Clock ........................................................ 45
4.13.1 Setting the Clock ............................................... 45
4.13.2 Interrogating for the Current Time ..................... 46
4.14 The Security Code .......................................... 47
4.14.1 Locking the Keypad........................................... 47
4.14.2 Unlocking the Keypad ....................................... 48
Chapter 5: Alarm Programming ................................. 49
5.1 Input Configuration .......................................... 49
5.1.1 Programming Input Configuration ....................... 50
5.1.2 Verifying Input Configuration ............................... 51
5.2 Enable/Disable Inputs ...................................... 51
5.2.1 Changing Enabled/Disabled Input Status ........... 51
5.2.2 Verifying Enabled/Disabled Input Status ............. 52
5.3 Input Recognition Time................................... 52
5.3.1 Programming Input Recognition Time................. 53
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
5.3.2 Interrogating Input Recognition Time .................. 54
5.4 Establishing High and LowTemperature Limits .. 54
5.4.1 Programming Temperature Limits for a
Selected Input ...................................................... 55
5.4.2 Disabling Alarm Response to High or
Low Temperature .................................................. 56
5.4.3 Interrogating High and Low Temperature Limits.. 57
5.5 Temperature Scale............................................ 57
5.6 Temperature Calibration .................................. 58
5.6.1 Programming Temperature Calibration ............... 58
5.6.2 Interrogating Temperature Calibration................. 59
5.7 Obtaining Current Temperature ...................... 59
5.8 AC Power Monitoring Enable/Disable............. 60
5.8.1 Enabling/Disabling the AC Power Alarm ............. 60
5.9 AC Power Failure Recognition Time ............... 61
5.9.1 Programming Power Failure Recognition Time ... 61
5.9.2 Interrogating Power Failure Recognition Time .... 62
5.10 Sound Alarm Monitoring ............................... 63
5.10.1 Programming Sound Alarm Sensitivity ............. 63
5.10.2 Interrogating Sound Sensitivity ......................... 64
5.10.3 Programming High Sound Alarm
Recognition Time .............................................. 64
5.11 High Sound Alarm Enable/Disable ............... 65
5.11.1 Changing Enabled/Disabled High Sound Alarm 66
5.12 Exit Delay ....................................................... 66
Chapter 6: Acknowledgment, Status Report, and
Remote Access......................................... 69
6.1 Alarm Acknowledgment................................... 69
6.1.1 Local Acknowledgment ........................................ 69
x
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1.2 Touch-ToneTM Acknowledgment ......................... 69
6.1.3 Callback Acknowledgment ................................... 70
6.2 Status Report................................................... 71
6.2.1 Example: Status Report, No Alarms ................... 72
6.2.2 Example: Status Report, Existing Alarms ........... 73
6.2.3 Example: Status Report, Disabled Inputs ........... 74
6.2.4 Battery Condition ................................................ 75
6.2.5 Remote Access by Touch-Tone™ Telephone...... 75
Appendix A:Troubleshooting..................................... 79
Appendix B: Accessories ........................................... 87
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
The OMEGAPHONE® OMA-P1104 is a fully-programmable,
environmental monitoring system that offers extensive on-site
and remote monitoring capability to small businesses, private
homes, farms, greenhouses, computer rooms, and remote
facilities. Designed for desktop or wall mounting, the
OMA-P1104 is simple to install, program and operate; no
changes to standard electrical or telephone service are required.
Connected to a telephone line, it will respond to an alarm by
dialing up to four separate telephone numbers. When the call is
answered, an “Alert Condition” message is delivered in
digitized speech.
The OMA-P1104 features built-in sensors to monitor a variety
of conditions:
• High sound level
• AC electric power failure
• Battery backup
• Temperature
Equipped with 4 alert inputs, additional sensors* can be added
for extended monitoring:
• Intrusion or unauthorized entry
• Water leaks and seepage
• Temperature
• Humidity
• Equipment operation
• Many other conditions that may require unique
monitoring solutions
* Refer to Appendix B for information on additional sensors
(available separately from Omega) that are best suited to your
application.
The status of each monitored condition is readily obtained at
the unit's installation site or remotely, by telephone. At the close
of every Status Report, time is provided for listening to on-site
sounds.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
To ensure reliable operation, the OMA-P1104 features power
backup capability; in the event of AC power failure,
six D-cell batteries (not included) will continue to power the
unit for approximately 10 hours.
This manual is comprised of the instructions and commands for
installing and operating the OMA-P1104. The Quick Start
chapter is included to speed understanding of programming and
operation. Communication and Alarm Programming chapters
demonstrate step-by-step methods for utilizing the full range of
available features. The Troubleshooting chapter provides
assistance in the event that problems are encountered.
Technical Support
If any questions arise upon installation or operation of the
OMA-P1104, please contact Omega Engineering Data Acquisi-
tion Group.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Correctly installing the OMA-P1104 will ensure proper
functioning of the unit. Please read the entire chapter before
starting the installation process.
Within the packaging will be a Warranty Registration Card.
Please take the time to fill this out and mail. The One Year
Limited Warranty is explained in the back of this manual.
2.1 Operating Environment
The OMA-P1104 should be installed and operated in an area
that provides space for wiring sensors to the screw terminals,
near an AC power source and telephone line. Operating
temperature ranges from 32° Fahrenheit (0° Celsius) to +120°
Fahrenheit (+49° Celsius).
NOTE
The OMA-P1104 is a sensitive electronic device.
Do not install the OMA-P1104 near strong
electrostatic, electromagnetic or radioactive
fields. Do not expose to fumes or corrosive
vapors.
2.2 Mounting
Flat Mount: Place the OMA-P1104 on top of a desk or other
horizontal surface. Wall Mount: Mount on a wall with two
screws using the keyholes on the back panel of the unit. Place
the screws or bolts 313/ " apart at the desired height from the
16
floor. Hook the unit over the screws and toward the floor. Refer
to Figure 2-1.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4
Chapter 2: Installation
+
+
+
- - -
+
+
+
- - -
Figure 2-2. Battery Installation
2.5 Starting the OMA-P1104
When the AC power transformer is first plugged into the
electrical outlet, the OMA-P1104 automatically starts in RUN
mode. The red LED light will begin to glow. The unit will
respond with,“Hello, this is Sensaphone® 1104.”
2.6 Run Mode and Standby Mode
Pressing the RUN/STANDBY key on the OMA-P1104 keypad
will alternately activate or deactivate the unit. If the unit is
activated and in RUN mode, the red LED (small red light on
the upper right of the unit's front panel) glows steadily. In
STANDBY mode, the red LED goes out, but will blink every
few seconds to indicate that power is still supplied to the unit.
In RUN mode, the OMA-P1104 is able to receive incoming
calls and to automatically dial out in the event of an alarm on
one of the monitored conditions. To enter STANDBY mode,
press RUN/STANDBY.
As soon as the OMA-P1104 enters STANDBY mode, it
responds with “Have a good day.” The red light immediately
goes out and then resumes with a blink every few seconds.
While in STANDBY mode, all functions are disabled, but
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
programmed memory is preserved. Upon exiting STANDBY
mode, any currently existing alert conditions will be an-
nounced.
NOTE
STANDBY mode is not equivalent to “power
off”—an electrical source, such as the 120 VAC,
or the battery backup, continues to provide full
power to the unit. If the unit is placed in
STANDBY mode, unplugged from the 120 VAC
outlet, and placed in storage, the batteries will
continue to power the OMA-P1104, discharging
until they fail. Consequently, batteries should
always be removed from the unit following
disconnection from any 120 VAC outlet, prior to
storage.
Press the RUN/STANDBY key again to return to RUN mode.
RUN
STANDBY
Figure 2-3. The RUN/STANDBY Key
2.7 Telephone Line
The OMA-P1104 will operate with all standard telephone
systems that accept pulse or tone dialing. The OMA-P1104
cannot be used on an extension line to dial its own telephone
number. Also, it may not be installed on a party line or pay
telephone line.
Certain private telephone systems and public switching
equipment may not accept the OMA-P1104 dialing or may
generate an unacceptable ring signal. In those cases, a dedi-
cated line may be required. Consult the supplier of your
telephone system if you encounter problems.
If you do not have a modular telephone extension at the
OMA-P1104’s location, you must contact your local telephone
company to have one installed (there is a charge for this
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
service). If you have four-pin jacks, adapters are available to
convert them to the modular plugs. Contact your local
telephone company or electronics parts store.
CAUTION
Never install telephone wiring during a lightning
storm. Never install telephone jacks in wet
locations unless the jack is specifically designed
for wet locations. Never touch uninsulated
telephone wires or terminals unless the telephone
line has been disconnected at the network
interface. Use caution when installing or
modifying telephone lines.
To install the telephone line, plug the modular telephone jack
provided into any standard RJ11 phone outlet. Refer to
Figure 2-4.
AC Power
Transformer
(plug into
120 VAC outlet)
GND
1
GND
2
GND
3
GND
4
RJ11 Outlet
(for modular
telephone jack)
Female Telephone Jack
(connect telephone here)
Modular Telephone Jack
(plug into RJ11 outlet)
Figure 2-4. Installing the Telephone Line
On the back of the OMA-P1104 is a female telephone jack.
This is provided so that a telephone or other answering device
may be used on the same line as the unit. It is not necessary to
hook up a telephone for the OMA-P1104 to operate.
2.8 The Microphone
The OMA-P1104 is provided with a built-in microphone which
is used to monitor high sound levels produced near the installa-
tion site. The sensitivity of the microphone is configurable and
will detect a continuous as well as a beeping alarm.
Other programming options that apply to the microphone
include setting the length of time before a high sound causes an
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
alarm.
If this sound level exists for 8 consecutive seconds (default) or
for the programmed length of time, the OMA-P1104 will dial
out with an alarm message.
NOTE
The proximity of the audible alarm to the
microphone is extremely important.
Normally, the OMA-P1104 and the audible
alarm must be in the same room. The maximum
distance can vary considerably depending on the
alarm, the acoustics, and the size of the room.
During an alarm dial-out, the microphone allows four-second
intervals to listen-in to sounds at the OMA-P1104’s location.
When calling for a Status Report, the microphone permits
listening to on-site sounds for a programmed time interval.
2.9 Alert Inputs
The OMA-P1104 can monitor up to 4 inputs (represented by
the numbered terminal screws shown in Figure 2-5, below).
1
2
3
4
GND
GND
GND
GND
Figure 2-5. Alert Inputs
Inputs are configured as either dry contact or temperature.
An input configured as dry contact can be used with any
normally open (N.O.) or normally closed (N.C.) device.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
“Open” refers to an opened circuit path; if conditions cause the
circuit to close, an alert condition occurs. “Closed” refers to a
continuous circuit path; if a closed circuit is opened, an alert
condition occurs. The OMA-P1104 determines the way inputs
are configured by the type of sensor connected to each alert
input (refer to Chapter 5, Section 5.1).
An input configured as “temperature” is designed to evaluate a
range of settings. The OMA-P1104 will read the temperature at
the sensor’s location and compare that value to programmed
high and low temperature limits. Temperature inputs must be
used with Phonetics Remote Temperature Sensor.
NOTE
Before wiring, it is advisable to disable the
inputs to prevent accidentally tripping an alarm.
See Chapter 5, Section 5.2.
2.10 Installing the Sensor
After you have selected the sensor, loosen the screw of the alert
input and its corresponding ground. Two wire leads are used to
connect any monitoring sensor. Fasten one lead to the num-
bered screw and the other lead to GND. Tighten both screws. If
the input was not disabled, the OMA-P1104 may recite its
“Alert Condition Exists” message as you connect the sensor. If
it does, just press any key to stop it. Re-enable the input after
wiring. Refer to Figures 2-6 and 2-7 for connecting a sensor to
an alert input.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
10
Chapter 2: Installation
Figure 2-7.Two Sensors Wired to Adjacent Inputs
NOTE
Do not use sensors, switches, or relays that
supply any voltage or current to the OMA-
P1104. Be aware of proximity to other electrical
wires or components when placing wires that
lead from the sensors to the unit. Avoid running
the wires near electrical devices that use high
voltage or current, such as motors, heavy
machinery, etc. This voltage may be inductively
coupled into the sensor wiring and could result in
damage to the the OMA-P1104’s circuitry. Try to
place wires at least 6 inches from other electrical
wiring or devices.
2.11 Multiple Sensors
The OMA-P1104 may have more than one sensor connected to
the same alert input, as long as the normal condition for each
sensor on the same alert input is identical (either all N.O. or all
N.C.). However, only one remote temperature sensor can be
used on each input.
When wiring several normally closed sensors on one input,
they must be connected in series. Connect one lead from the
first sensor to the numbered screw of the alert input. Next, take
the other lead from the first sensor and connect it to one lead
from the next sensor. Continue connecting sensors end-to-end
until you have connected all of your sensors. Take the second
lead from the last sensor and connect it to the ground screw on
the OMA-P1104. See Figure 2-8. Multiple N.C. sensors are
typically magnetic reed switches to monitor the security of
windows and doors.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
GND
1
GND
2
GND
3
GND
4
~
~
~
~
Multiple normally-closed
sensors wired in series
(example using Input 2)
Alert condition
occurs when a
switch is opened
Figure 2-8. Multiple Normally Closed Sensors
To wire several normally open sensors to one alert input,
connect them in parallel. To do this, take one lead from each
sensor and attach it to the numbered terminal. Then, take the
second lead from each sensor and attach each to the corre-
sponding ground screw. Refer to Figure 2-9.
1
2
3
4
GND
GND
GND
GND
Alert condition occurs
when a normally open
switch closes.
Figure 2-9. Multiple Normally Open Sensors
OMA-P1104
2.12 Outdoor Wiring
When wiring sensors outdoors, DO NOT allow exposed wires
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
to run freely in open air; under such conditions, the OMA-
P1104 is susceptible to serious damage during a lightning
storm. Depending upon the distance outdoor wiring must
travel, consideration should be given to use of shielded wire
inside a metal conduit. Both shield and conduit should be
connected to earth ground. This prevents stray voltage from
entering the unit.
sensor
Model 1104
Figure 2-10. Potential Sensor Damage from Stray Electrical Noise
2.13 Disconnecting the OMA-P1104 for Storage or
Seasonal Use.
If you plan to employ the OMA-P1104 as a seasonal “watch-
dog” for a few months during the year, you m ust disconnect
allwiresfr omtheunitcompletel ytoa voiddama getothe
circuitry when the unit is not in use
. If the unit is unplugged
but left in place with all the sensors still connected, the wires
act as antennae that draw in any stray “electrical noise” from
such devices as fans, blowers, microwaves, etc.
Additionally, it is important to remove the batteries, or they will
discharge until they fail.
Preserve your OMA-P1104 during the off-season, or
when not in use:
13
• Remove the sensor wires at the screw terminals
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
NOTES
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Quick Start
This section presents a useful guide for first-time programming
of the OMA-P1104. Follow instructions for installation before
attempting to program the OMA-P1104. Refer to
Chapter 2: Installation.
3.1 The Local Keypad
Programming is accomplished using the local keypad (shown
below, Figure 3-1). Notice that a single key has several func-
tions assigned to it; programming results are determined by
the order in which keys are pressed.
Individual keystrokes are illustrated to show programming
steps in the correct order. If you make a mistake by entering the
wrong key, do not press another key until you hear the message,
“Error 1.” Then, start over with the first key in the
programming sequence.
Figure 3-1. The OMA-P1104 Keypad
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
3.2 Preparation for Programming
Read complete instructions in Chapter 2: Installation, and make
sure to follow these steps first:
1. Plug the AC adaptor into the 120 VAC outlet.
2. Install the batteries.
3. Connect the OMA-P1104 to a telephone line.
When these steps are completed, the OMA-P1104 is fully
operational and able to monitor temperature, high sound,
AC power failure and battery backup condition; it can also be
called on the telephone for a Status Report or used for listening
to on-site sounds from any remote location. Now, the unit is
ready for programming.
3.3 Quick-Start Programming Steps
Step 1: Set Configuration of Inputs
The OMA-P1104 will scan the 4 external inputs and determine
if they are N.O. (normally open), N.C. (normally closed), or
Temperature. If external sensors are added, make sure they are
in their normal positions before proceeding—refer to
Chapter 5, Section 5.1.
1. Press STANDBY to place the OMA-P1104 in Standby
mode.
RUN
STANDBY
2. If you have external sensors available, wire the sensors to
the inputs on the back of the OMA-P1104 (see Chapter 2,
Section 2.10). Otherwise, skip this step and move to
step 3.
3. Press RUN. The red light glows when the OMA-P1104
returns to Run mode.
RUN
STANDBY
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Quick Start
4. Press SET.
SET
#
5. Press CONFIGURE.
STATUS
CONFIGURE
6. The OMA-P1104 will audibly recite the new configura-
tion for each of the four inputs, responding with “OK,” if
it detects N.O. (normally open), “beep-OK,” if it detects
N.C (normally closed) or “Temperature,” if it detects
temperature (regardless of whether all the inputs have
attached sensors or not). If an input is unused, it is treated
as normally open.
Step 2: Set the ID Number
It is recommended that you set the ID number to reflect the
telephone number on which the OMA-P1104 is installed.
1. Press SET.
SET
#
2. Press ID NUMBER.
0
ID NUMBER
POWER
3. Using the number keys, enter the digits (up to 16 are
permitted) for the ID number. The OMA-P1104 will recite
the digits as they are pressed.
1
3
INTERCALL
TIME
2
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4. Press ENTER. The 1104 will respond: “Enter.”
ENTER
TONE
PM
Step 3: Set Dial-Out Telephone Numbers
To program dial-out telephone numbers:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
3. Select which telephone number to program. Press any
unassigned number key (from 1 to 4) to represent the new
telephone number entry. OMA-P1104 will respond:
“Enter number.”
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. Enter the complete telephone number using the number
keys. The OMA-P1104 will recite the digits as they are
pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER. The unit will respond: “Enter.”
ENTER
TONE
PM
6. Repeat above procedure to program up to four separate
telephone numbers.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Quick Start
Step 4: Set Temperature Limits
High and low temperature limits can be separately programmed
for each input that is configured as temperature. Limits can
range from –20° to +150° Fahrenheit, or from –30° to 65°
Celsius. Default settings are: 10° F for low temperature and
100° F for high temperature. Do not set temperature limits too
close to normal room temperature, since minor fluctuations
could result in frequent and unnecessary alarm dialouts.
1. Press SET.
SET
#
2. Press TEMP LIMITS.
5
TEMP LIMITS
3. From the number keys, press a number (from 1 to 4) that
corresponds to the temperature input being programmed.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
The OMA-P1104 responds: “Enter low temperature
limit.”
4. Using the number keys, enter a value for low temperature
limit. The OMA-P1104 will recite the digits as they are
pressed. If a negative number is required, first press
PAUSE, then enter the number.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER.
ENTER
TONE
PM
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
The OMA-P1104 responds: “Enter high temperature
limit.”
6. Using the number keys, enter the value for high
temperature limit. The OMA-P1104 will recite the digits
as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
This concludes minimum programming to achieve normal
operation of the OMA-P1104. In additon to the programming
just accomplished, default settings for many more features take
effect when the unit is first powered. You will be able to
reprogram most of these factory-set defaults to suit your
application.
For a complete explanation of each feature (with illustrations of
keystrokes), refer to Chapter 4: Communications Programming
and Chapter 5: Alarm Programming.
To gain a basic understanding of how the alarm dial-out feature
works, refer to this chapter, Section 3-4. For extended informa-
tion regarding dial-out and related programmable parameters,
refer to Chapter 7: Operation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Quick Start
3.4 Summary of the Alarm Dial-Out Process
Action—Response
Programmable Feature
• Recognition Time
1. THE OMA-P1104 DETECTS
AN ALERT CONDITION
This is the programmed
waiting period to determine if
an alert condition has persisted
long enough to be considered a
valid alarm. If the sensor
returns to normal within
recognition time, then no
alarm will occur.
An alert condition is not the same as a
valid alarm—the condition must
continue for the programmed time
period, or Recognition Time, before it is
recognized as a valid alarm.
2. A VALID ALARM IS CONFIRMED
• Call Delay
An audible, on-site alarm message
begins and continues until the alarm is
acknowledged. (If the Mute feature is
turned on, there is no on-site message.)
Call Delay is activated.
This is the programmed
waiting period, before the first
telephone number is called, to
report an alarm.
• Intercall Time
3. DIAL-OUT BEGINS
This is the programmed
Dial-out begins by calling telephone
number 1 to report an alarm.
waiting period, in between
sequential dialing of telephone
numbers, to report an alarm.
If there is no acknowledgment, the
OMA-P1104 waits the programmed
Intercall Time before dialing subsequent
telephone numbers. Dial-out continues
in this manner, cycling through the
remaining telephone numbers, for the
programmed Max Calls.
• Max Calls
This is the total number of
telephone calls that will be
dialed in response to any valid
alarm. Telephone numbers are
dialed sequentially, and
continue to cycle until the
maximum number of calls is
reached. If no acknowledg-
ment occurs, then at the
completion of Max Calls, all
alarms are automatically
acknowledged.
4. THE ALARM IS
ACKNOWLEDGED
When the alarm is acknowledged, the
dial-out process is cancelled and the
audible, on-site alarm message stops.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
NOTES
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
This chapter explains the keypad commands for
communications programming of the OMA-P1104,
including interrogation and resetting of the following:
• The Unit ID Number
• Dial-out Telephone Numbers
• Tone or Pulse Dialing
• Special Dialing with Pagers, Beepers and Access
Numbers.
• Rings Until Answer and Telephone Answering Device
Compatibility
• Listen-in Time
• Call Delay
• Local Voice Mute
• Voice Repetitions
• Intercall Time
• Maximum Number of Calls
• The Clock
• Security Code
4.1 The Unit ID Number
The Unit ID Number is the identification number of the
OMA-P1104. This number may be the same as the telephone
number where the unit is installed, or it may be designated
using any number that best suits your application.
The purpose of the Unit ID Number is to immediately provide
the source of any alarm, especially when using multiple
OMA-P1104 units in a complex monitoring system. When
the OMA-P1104 is called from a remote location, it always
begins its message with the identification number:
“Hello, this is telephone number (Unit ID Number).”
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4.1.1 Programming the ID Number
To program the ID Number:
1. Press SET.
SET
#
2. Press ID NUMBER.
0
ID NUMBER
POWER
3. Using the number keys, enter up to 16 digits for the ID
number. The OMA-P1104 will recite the digits as they are
pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. Press ENTER. The OMA-P1104 will respond: “Enter.”
ENTER
TONE
PM
4.1.2 Interrogating the ID Number
To interrogate the ID numbers:
1. Press WHAT IS.
WHAT
IS
*
2. Press ID NUMBER. The OMA-P1104 will recite the Unit
ID Number programmed.
0
ID NUMBER
POWER
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
4.2 Dial-out Telephone Numbers
The OMA-P1104 can store up to four 32-digit phone numbers.
These are the numbers that will be called during dial-out.
In the event of an alarm, the numbers are dialed sequentially,
1 through 4. Begin programming the first telephone number by
assigning it to the key labeled with the number 1 on the keypad,
and continue to assign any other telephone numbers in
numerical order. A pause, pound or asterisk can be added to an
individual phone number to access different phone and beeper
systems. See Special Dialing, Section 4.4.
4.2.1 Programming Dial-out Telephone Numbers
To program dial-out telephone numbers:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
3. Select which telephone number to program. Press any
unassigned number key (from 1 to 4) to represent the new
telephone number entry. The OMA-P1104 will respond:
“Enter number.”
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. Enter the complete telephone number using the number
keys.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
5. Press ENTER. The unit will respond with “Enter.”
ENTER
TONE
PM
6. Repeat above procedure to program up to four separate
telephone numbers.
4.2.2 Interrogating a Dial-out Telephone Number
To interrogate dial-out telephone numbers:
1. Press WHAT IS.
WHAT
IS
*
2. Press PHONE NUMBER.
PHONE
NUMBER
3. Press a number key (from 1 to 4).
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
OMA-P1104 will recite the corresponding telephone
number. If there is no number programmed for a
particular key, the unit will respond: “No number.”
4.2.3 Erasing a Telephone Number
To erase a telephone number:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
3. Press the number key (from 1 to 4) representing the
telephone number you want to erase.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. Press ENTER. The OMA-P1104 will sa“Enpte.”.
27
Omegaphone® OMA-P1104 User’s Manual
4.4.1 Special Dialing Keys
The following designated keys represent special functions when
used with PHONE NUMBER entries:
1. Pause
RING/TAD
PAUSE
AM
PAUSE represents a four second pause in dialing. It can
be used when an access number is required before dialing
to an outside line. (For example, in some cases a "9" or
other number, must be dialed first, in order to get a dial
tone for an outside line.) When interrogating telephone
numbers, PAUSE is audibly represented by a “beep.”
2. Pound (#)
SET
#
A pound may be required when calling some phone or
beeper systems. When interrogating telephone numbers,
pound (#) is audibly represented by the word “twelve.”
3. Asterisk (*)
WHAT
IS
*
An asterisk may be required when calling some phone or
beeper systems. When interrogating telephone numbers,
asterisk (*) is audibly represented by the word “eleven.”
4. Code
CODE
MUTE
CODE instructs the OMA-P1104 to wait until the call is
answered before continuing. When interrogating
telephone numbers, CODE is audibly represented by the
word “fourteen.”
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
NOTE
Each time a pause, pound (#) or asterisk (*) is
incorporated in a programming sequence, it is
counted as one digit toward the total of 32 digits
allowed.
4.4.2 Incorporating a Pause
Incorporate PAUSE to access an outside telephone line:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
3. Press any unassigned number key (from 1 to 4) to
represent the new telephone number entry. OMA-P1104
will respond: “Enter number.”
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. From the number keys, enter the access digit (i.e., 9).
The OMA-P1104 will recite the digit.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press PAUSE. The OMA-P1104 will “beep.”
RING/TAD
PAUSE
AM
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
6. Enter the complete telephone number (1 + area code)
using the number keys. The OMA-P1104 will recite the
digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 will say “Enter.”
ENTER
TONE
PM
4.4.3 Incorporating a Pound (#) or Asterisk (*)
Incorporate a pound or asterisk if it is normally included in
telephone number:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
3. Press any unassigned number key (from 1 to 4) to
represent the new telephone number entry. OMA-P1104
will respond: “Enter number.”
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
4. Enter the telephone number using the number keys. The
OMA-P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Position the pound (#) or asterisk (*) within the telephone
number where required by pressing SET (where the pound
is located) or WHAT IS (where the asterisk is located).
The OMA-P1104 will beep each time pound or asterisk is
pressed.
WHAT
SET
IS
*
–OR–
#
6. Enter any remaining digits of the telephone number.
7. Press ENTER. The OMA-P1104 will say “Enter.”
ENTER
TONE
PM
4.4.4 Special Dialing to a Beeper or Pager
The following example demonstrates just one solution to
programming the OMA-P1104 for dialing to a beeper or pager.
Many other key sequences will also work. Start with steps 1–3
below; next, enter special dialing keys where required for your
beeper or pager service.
To incorporate a pound or asterisk:
1. Press SET.
SET
#
2. Press PHONE NUMBER.
PHONE
NUMBER
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
3. Press any unassigned number key (from 1 to 4) to
represent the new telephone number entry.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. Enter the complete telephone number using the number
keys. The OMA-P1104 will recite the digits as they are
pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press CODE. This instructs the OMA-P1104 to wait for
the telephone call to be answered by the beeper or pager
service. (A voice message will not occur—only digital
tones are used.)
CODE
MUTE
6. Now press PAUSE once to activate a four second delay.
This assumes the call is answered by a beeper/pager
service that immediately delivers a prerecorded voice
message. PAUSE may be pressed more than once to
program more time for the beeper/pager service to finish
its message. Each press of PAUSE allocates four addi-
tional seconds. The OMA-P1104 will “beep” with each
press.
RING/TAD
PAUSE
AM
7. Enter a telephone number or custom code number that
will identify the OMA-P1104 as the caller to your beeper
or pager. A code may consist of any number(s) you
designate. Many users find it convenient to use the
telephone number to which the OMA-P1104 is connected.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
8. A pound or asterisk may be required in some dialing
situations. If required, position the pound (#) or asterisk
(*) within the telephone number where required by
pressing SET (where the pound is located) or WHAT IS
(where the asterisk is located). The OMA-P1104 will
“beep” each time pound or asterisk is pressed. Enter any
remaining digits of the telephone number.
WHAT
SET
IS
*
–OR–
#
9. Press ENTER. The OMA-P1104 will say “Enter.”
ENTER
TONE
PM
4.5 Rings Until Answer
Rings Until Answer is the programmed number of times the
telephone rings before the OMA-P1104 will answer an incom-
ing call. This can be set from 1 to 15 rings. The default value is
4.
4.5.1 Programming Rings Until Answer
To program Rings Until Answer:
1. Press SET.
SET
#
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
2. Press RING/TAD. The OMA-P1104 will respond: "Enter
number."
RING/TAD
PAUSE
AM
3. Using the number keys, enter a value.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. Press ENTER. The OMA-P1104 will respond: "Enter."
ENTER
TONE
PM
4.5.2 Interrogating Rings Until Answer-
To interrogate Rings Until Answer:
1. Press WHAT IS.
WHAT
IS
*
2. Press RING/TAD.
RING/TAD
PAUSE
AM
4.6 TAD (Telephone Answering Device)
The TAD feature is especially useful because it integrates the
operation of the OMA-P1104 with your telephone answering
device in a way that retains the full flexibility of each system.
This allows you to have on-demand telephone access to the
OMA-P1104, for obtaining a Status Report, or for issuing call-
in commands, while your telephone answering device is set to
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
receive outside calls. Programming for use with a telephone
answering device (TAD) is always used in conjunction with
Rings Until Answer, detailed in section 4.5.
NOTE
The TAD feature only applies to answering
devices connected to the same telephone line as
the OMA-P1104.
4.6.1 TAD Enable/Disable
To enable/disable the TAD feature:
1. Press SENSOR ON/OFF.
SENSOR
ON/OFF
2. Press RING/TAD.
RING/TAD
PAUSE
AM
The OMA-P1104 will respond: “On.” (If the OMA-P1104
says “Off,” repeat steps 1 and 2 to reactivate TAD.)
4.6.2 Using the TAD Feature
1. Make sure the TAD feature is enabled on the OMA-
P1104. (The default setting is disabled, so you must
enable it first.)
2. Determine the number of rings your telephone answering
device uses to answer the telephone. (Most answering
devices require 4 rings; others are selectable.)
3. On the OMA-P1104, program Rings Until Answer to a
greater number than the number of rings set on your
answering machine.
Example:
Telephone answering device, rings = 4
OMA-P1104, Rings Until Answer = 6
Using the procedure just outlined, all incoming calls will be
answered by the telephone answering device, allowing it to
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
operate normally. With the programming just accomplished, the
OMA-P1104 can be accessed remotely, by telephone, to obtain
the Status Report.
1. Dial the telephone number of the OMA-P1104.
2. Let the telephone ring once and then hang up.
3. Wait approximately ten seconds
4. Call the OMA-P1104 back.
It will answer the telephone on the first ring.
Explanation: The pattern of one ring, followed by a second call
(within 30 seconds), signals the OMA-P1104 to answer your
incoming call, excluding the telephone answering device.
NOTE
Special Case: If the OMA-P1104 shares the same
line with a telephone answering device, and
during certain time periods, frequent, incoming
calls are expected on that line, then you may
want to temporarily disable the TAD feature. If
you leave the TAD enabled, it will not adversely
affect normal operation, but if two outside
telephone calls are received within the same
30-second time window, the OMA-P1104 will
interpret this pattern as a signal to answer the
telephone. If this occurs, press any key on the
OMA-P1104 to hang up.
4.6.3 No TAD In Use
If a telephone answering device is not used on the same
telephone line as the OMA-P1104, make sure that the
TAD feature is disabled, or turned off. Only Rings Until
Answer programming will determine how incoming calls
are answered. For example, if you program Rings Until
Answer to 3, incoming calls will be answered in 3 rings.
4.7 Listen-in Time
The Listen-in Time is the amount of time you can listen to
sounds from the OMA-P1104’s built-in microphone at its
installation site. When you call in for a Status Report, the
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
OMA-P1104 announces Listen-in Time at the end of its first
round of status readings, saying, “Listen to the sound level for
(programmed time entered).” The programmable range is from
0 to 255 seconds (or up to 4.17 minutes). The default value is
15 seconds.
NOTE
The microphone is also used to monitor high
sound level. See Chapter 5, Section 5.10 through
Section 5.11.1.
4.7.1 Programming the Listen-in Time
To program the Listen-in Time:
1. Press SET.
SET
#
2. Press LISTEN TIME. The OMA-P1104 will respond:
“Enter seconds.”
9
LISTEN TIME
SOUND
3. Using the number keys, enter the seconds. The OMA-
P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. Press ENTER. The OMA-P1104 will respond: “Enter.”
ENTER
TONE
PM
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4.7.2 Interrogating the Listen-in Time
To interrogate the Listen-in Time:
1. Press WHAT IS.
WHAT
IS
*
2. Press LISTEN TIME. The OMA-P1104 will recite the
listen time in seconds programmed.
9
LISTEN TIME
SOUND
4.8 Call Delay
Call Delay is the programmed length of time the OMA-P1104
waits, following detection of an alarm, before it begins the dial-
out sequence. This applies only to the first call. (Delay time
between calls is also programmable: refer to Intercall Time,
Section 4-11.)
The purpose for Call Delay is to allow time for personnel at the
OMA-P1104’s installation site to respond to and cancel an
alarm before dial-out begins. During this time, the OMA-P1104
will audibly repeat its “alert condition” message (unless the
Local Voice Mute feature has been activated—refer to Section
4.9). The default for Call Delay is 30 seconds. Call Delay can
be programmed from 0 seconds to 60 minutes (1 hour).
4.8.1 Programming the Call Delay
To program the Call Delay:
1. Press SET.
SET
#
2. Press CALL DELAY.
1
CALL
DELAY
The OMA-P1104 will respond: “Enter minutes.”
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
3. Using the number keys, enter the minutes.
The OMA-P1104 recites the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. Press ENTER. The OMA-P1104 responds: “Enter
seconds.”
ENTER
TONE
PM
5. Using the number keys, enter the seconds. The OMA-
P1104 recites the digits as you press them.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
6. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
4.8.2 Interrogating Call Delay
To interrogate Call Delay:
1. Press WHAT IS.
WHAT
IS
*
2. Press CALL DELAY.
1
CALL
DELAY
The OMA-P1104 will recite the programmed Call Delay.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4.9 Local Voice Mute
When the OMA-P1104 dials out to report an alarm, it also
audibly recites the alarm message at its installation site. The
Local Voice Mute command allows you to turn off the voice at
the OMA-P1104’s site during alarm dialouts and status call-ins.
This feature is used to prevent intruders or unauthorized
persons from hearing the alarm dial-out message or from
hearing the Status Report during an off-site call.
4.9.1 Enable/Disable Local Voice Mute
To enable/disable Local Voice Mute:
1. Press SENSOR ON/OFF.
SENSOR
ON/OFF
2. Press MUTE.
CODE
MUTE
The OMA-P1104 will say “On,” to indicate that Local
Voice Mute is enabled, or“Off,” to indicate that it is
disabled.
3. Repeat key sequence to switch between enabled or
disabled Local Voice Mute.
4.10 Voice Repetitions
The Voice Repetitions feature allows programming of the
number of times the alarm message is delivered per phone call
during alarm dial-out.
The maximum repetitions may be set to 10; the default is
3 repetitions.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
4.10.1 Programming Voice Repetitions
To program Voice Repetitions:
1. Press SET.
SET
#
2. Press VOICE REPS.
2
VOICE
REPS
The OMA-P1104 will respond: “Enter number.”
3. Using the number keys, enter a value from 0 to 10.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. Press ENTER. The OMA-P1104 will respond: “Enter.”
ENTER
TONE
PM
4.10.2 Interrogating Voice Repetitions
To interrogate Voice Repetitions:
1. Press WHAT IS.
WHAT
IS
*
2. Press VOICE REPS.
2
VOICE
REPS
The OMA-P1104 will recite the number programmed.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4.11 Intercall Time
The Intercall Time is the programmable period of time the
OMA-P1104 waits in calling subsequent telephone numbers.
Intercall Time is activated only after alarm dial-out to the first
telephone number fails to be acknowledged. This period can
be programmed from 10 seconds to 60 minutes. The default
intercall time is 1 minute.
If an incoming telephone call is made to the OMA-P1104
during Intercall Time (in between its dialing of subsequent
telephone numbers to report an alarm), it will answer the
incoming call and immediately report any existing alarms. The
manner in which the incoming call is answered depends upon
whether or not TAD is enabled or disabled:
• If TAD (Telephone Answering Device) is enabled,
Rings Until Answer will be 1.
• If TAD is disabled, Rings Until Answer will be 10.
Refer to Section 4.5, Rings Until Answer, and Section 4.6,
TAD (Telephone Answering Device).
4.11.1 Programming Intercall Time
To program Intercall Time:
1. Press SET.
SET
#
2. Press INTERCALL TIME.
3
INTERCALL
TIME
The OMA-P1104 will respond: “Enter minutes.”
3. Using the number keys, enter the minutes.
The OMA-P1104 recites the digits as you press them.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
4. Press ENTER. The OMA-P1104 will respond: “Enter
seconds.”
ENTER
TONE
PM
6. Using the number keys, enter the seconds. The OMA-
P1104 recites the digits as you press them.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
4.11.2 Interrogating Intercall Time
To interrogate Intercall Time:
1. Press WHAT IS.
WHAT
IS
*
2. Press INTERCALL TIME.
3
INTERCALL
TIME
The OMA-P1104 will recite the programmed
Intercall Time.
4.12 Maximum Number of Calls (Max Calls)
The Max Calls feature controls the total number of repeated
calling attempts by the OMA-P1104 in the event of an alarm.
When an alarm occurs, the dial-out process begins, and
continues to cycle through your programmed telephone
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
numbers until a maximum number of calls is reached. The Max
Calls setting regulates the number of calls that will be made as
a result of any alarms; if more than one alarm is detected at
once, or if a second alarm occurs during dial-out on the first
alarm, the Max Calls setting will start the calling process from
zero, until the programmed number of calling attempts are
completed.
The default setting for Max Calls is 16, but it may be
programmed from 0 to 255 calls. Max Calls is cancelled when
an alarm is acknowledged. If the maximum number of calls is
completed and no alarm acknowledgement has occurred, the
OMA-P1104 will automatically acknowledge any alarm and
stop the dial-out.
NOTE
If only one telephone number is programmed, the
OMA-P1104 will dial out a maximum of 15
times to report an alarm.
4.12.1 Programming Max Calls
To program Max Calls:
1. Press SET.
SET
#
2. Press MAX CALLS.
4
MAX CALLS
The OMA-P1104 will respond: “Enter number.”
3. Using the number keys, enter a value. The OMA-P1104
will recite the digits as you press them.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
5. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
4.12.2 Interrogating Max Calls
To interrogate Max Calls programmed:
1. Press WHAT IS.
WHAT
IS
*
2. Press MAX CALLS.
4
MAX CALLS
The OMA-P1104 will recite the value set for Max Calls.
4.13 The Clock
The OMA-P1104 has a built-in clock. The power-up time is
12 AM. The clock will keep time from 12 AM until you
program the current time. It will then keep time from your
programmed time. If the AC power fails, the clock will con-
tinue to keep time until the battery back-up fails. It will then
reset to 12 AM when power is restored. An incorrect time is a
good indication that the power has failed and the batteries
have been expended.
4.13.1 Setting the Clock
To set the clock:
1. Press SET.
SET
#
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
2. Press CLOCK.
8
CLOCK
3. Using the number keys, enter the correct time. The
OMA-P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
4. If the time is AM, press the AM key. The OMA-P1104
will “beep.” (If the time is PM , there is no key to press—
the clock will be automatically set to PM if AM is not set.)
RING/TAD
PAUSE
AM
5. Press ENTER. The OMA-P1104 will say “Enter.”
ENTER
TONE
PM
Example: You want to set the clock to 12:45 AM. Press the
following keys in the order shown:
SET…CLOCK…1…2…4…5…AM…ENTER.
4.13.2 Interrogating for the Current Time
To interrogate the OMA-P1104 for the current time:
1. Press WHAT IS.
WHAT
IS
*
2. Press CLOCK. The OMA-P1104 will recite the
programmed time.
8
CLOCK
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Communications Programming
4.14 The Security Code
The Security Code is the last step after setting all other pro-
gramming parameters for the OMA-P1104. The code consists
of a 4-digit number you select and will effectively prevent
unauthorized changes to the OMA-P1104’s programming.
When the Security Code is activated, all keyboard program-
ming is inaccessible. The OMA-P1104 may be interrogated
using the WHAT IS key, but the keyboard must be unlocked,
via the Security Code, before any additional programming is
possible.
4.14.1 Locking the Keypad
To program the Security Code:
1. Press SET.
SET
#
2. Press CODE.
CODE
MUTE
The OMA-P1104 will say “Enter security code.”
3. Using the number keys, enter 4 digits. The OMA-P1104
says, “OK.” The keyboard is now locked.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
If unauthorized persons attempt to set a parameter, an
error message, “Error 2,” is returned. Whenever any
operation except WHAT IS takes place without entering
the security code first, this error message occurs.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
4.14.2 Unlocking the Keypad
To unlock the keyboard:
1. Press WHAT IS.
WHAT
IS
*
2. Press CODE.
CODE
MUTE
The OMA-P1104 will say “Enter Security Code.”
3. Using the number keys, enter the digits for the code.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
SOUND
7
RECOGNITION
TIME
8
LISTEN TIME
.
CLOCK
0
ID NUMBER
POWER
If the correct code is entered, the OMA-P1104 will say
“OK.” If the wrong code is entered, the OMA-P1104 will
say “Error 2.”
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
This chapter explains the alarm programming and monitoring
capabilities of the OMA-P1104, with specific instructions for
the following features:
• Configure inputs as dry contact or temperature
• Enable/disable inputs
• Program alarm Recognition Time for each input
• Program high and low temperature limits
• Disable alarm response to high or low temperature
• Program temperature in Fahrenheit or Celsius scale
• Calibrate temperature
• Obtain current temperature
• Program AC power-failure Recognition Time
• Enable/disable AC power monitoring
• Program sound level sensitivity
• Program high sound Recognition Time
• Disable alarm response to high sound
• Use Exit Delay via Status Report
5.1 Input Configuration
In preparing the OMA-P1104 to sense an alert condition, the
inputs must be configured as dry contact (either open or
closed) or as temperature inputs. The default setting for input 1
is temperature; for inputs 2-4, the default is dry contact and
open. To configure input normality, sensors are first wired to
the terminal strip at the back of the unit. (Refer to Chapter 2,
Section 2.9–2.12, for an explanation on wiring inputs.)
The configuration process directs the OMA-P1104 to initialize
the 4 inputs and establish normal settings. Any change in the
status of an input (for example, from a normally open contact
to a suddenly closed contact) is recognized as an alert condi-
tion. In the case of a temperature input, an alert condition is
recognized when established temperature limits are exceeded.
NOTE
Before starting keyboard commands to configure input
normality on the OMA-P1104, it is very important to
check that the sensors you have wired to the unit are set
in their normal, non-alarm positions.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
For example, if a magnetic reed switch (a normally-closed
sensor used to detect unauthorized entry) has been wired
to the OMA-P1104, make sure that the door or window to
be monitored is shut before configuring the input. If a
motion-detector is wired to the unit, it is advisable to
block all sources of motion from the sensor before and
during configuration.
5.1.1 Programming Input Configuration
1. Press STANDBY to place the OMA-P1104 in
Standby mode.
RUN
STANDBY
2. Wire sensors to the inputs to the back of the OMA-P1104
(see Chapter 2, Section 2.10).
3. Press RUN. The red light glows when the OMA-P1104
returns to Run mode.
RUN
STANDBY
4. Press SET.
SET
#
5. Press CONFIGURE.
STATUS
CONFIGURE
6. The OMA-P1104 audibly recites the configuration for
each of the four inputs:
• If the input is normally open, the OMA-P1104 recites
the number of the input and says“OK.”
• If the input is normally closed, the OMA-P1104 recites
the number of the input, followed by a “beep”
and“OK.”
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
• If the input is configured as temperature, the
OMA-P1104 recites the number of the input, followed
by “Temperature.”
5.1.2 Verifying Input Configuration
Input configuration can be verified when interrogating the
OMA-P1104 for a complete Status Report. Refer to Chapter 6
for a more detailed description of the Status Report.
5.2 Enable/Disable Inputs
This function allows you to enable or disable an input’s
response to an alert condition. An enabled input will respond to
an alert condition and allow dial-out. A disabled input will
cause dial-out to be suppressed, but any existing alert condi-
tions will be revealed during the Status Report. Enable/disable
programming is useful during wiring of inputs (see Chapter 2)
or when a condition needs to be monitored, but is not critical
enough to be programmed for dial-out reporting. It is important
to verify input status after performing any task that requires
disabling. The default setting for all inputs is enabled (ON).
If an alert condition exists when inputs are re-enabled,
Recognition Time will restart—refer to Section 5.3.
5.2.1 Changing Enabled/Disabled Input Status
1. Press SENSOR ON/OFF.
SENSOR
ON/OFF
2. Press the number (1 to 4) of the selected input to enable/
disable. The OMA-P1104 says “Off” to indicate disabled
or “On” to indicate enabled.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
5.2.2 Verifying Enabled/Disabled Input Status
1. Press WHAT IS.
WHAT
IS
*
2. Press STATUS.
STATUS
CONFIGURE
The OMA-P1104 audibly recites the current status of every
input. In a Status Report, each input is first identified by its
input number, followed by a report that specifies parameters
currently affecting that input. If an input is disabled, the word
“Off” immediately follows the number recited for that input.
For example, input 3 is configured as a normally open, dry
contact input. During the Status Report:
• If disabled, the OMA-P1104 recites:
“Number 3—Off—OK,” for input 3.
• If enabled, the OMA-P1104 recites:
“Number 3—OK,” for input 3.
In another example, input 2 is configured as a temperature
input. The current temperature is 76 degrees. During a Status
Report:
• If disabled, the OMA-P1104 recites “Number 2—Off—
76 degrees—OK”.
• If enabled, the OMA-P1104 recites “Number 2—
76 degrees—OK”.
5.3 Input Recognition Time
The Input Recognition Time is the length of time an alert
condition must be present before a valid alarm exists and dial-
out is activated. This time period is programmable, from 0
minutes, 0 seconds (for immediate response) up to a period of
272 minutes, 0 seconds. If an alert condition begins and then
clears within the established Recognition Time, no dial-out will
occur. When an alert condition continues beyond the
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
programmed Recognition Time, the OMA-P1104 initiates dial-
out. The default setting for Input Recognition Time is 0
minutes, 3 seconds.
5.3.1 Programming Input Recognition Time
1. Press SET.
SET
#
2. Press RECOGNITION TIME.
7
RECOGNITION
TIME
3. Press the number (1 to 4) of the selected input to be
programmed.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
The OMA-P1104 responds: “Enter minutes.”
4. Using the number keys, enter the minutes. For example, to
set a Recognition Time of five minutes, simply press “5”
on the keypad. The OMA-P1104 recites the digits as they
are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER. The OMA-P1104 responds: “Enter
seconds.”
ENTER
TONE
PM
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
6. Using the number keys, enter the seconds. The
OMA-P1104 recites the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
5.3.2 Interrogating Input Recognition Time
1. Press WHAT IS.
WHAT
IS
*
2. Press RECOGNITION TIME.
7
RECOGNITION
TIME
3. Press the corresponding input key (1 to 4).
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
The OMA-P1104 recites the programmed Recognition
Time for that input.
5.4 Establishing High and Low Temperature Limits
High and low temperature limits can be separately programmed
for each input configured as temperature. Limits can range
from
–20° to +150° Fahrenheit, or from –30° to 65° Celsius.
When temperature limits exceed high or low settings, the
OMA-P1104 will dial out with an alarm message. Default
settings are: 10° F for low temperature and 100° F for high
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
temperature.
5.4.1 Programming Temperature Limits
for a Selected Input
1. Press SET.
SET
#
2. Press TEMP LIMITS.
5
TEMP LIMITS
3. From the number keys, press a number (from 1 to 4) that
corresponds to the temperature input being programmed.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
The OMA-P1104 responds: “Enter low temperature
limit.”
4. Using the number keys, enter a value for low temperature
limit. The OMA-P1104 will recite the digits as they are
pressed. If a negative number is required, first press
PAUSE, then enter the number.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER.
ENTER
TONE
PM
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
The OMA-P1104 responds: “Enter high temperature
limit.”
6. Using the number keys, enter the value for high tempera-
ture limit. The OMA-P1104 recites the digits as they are
pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
NOTE
Do not set temperature limits too close to normal
room temperature. Minor temperature fluctua-
tions could result in frequent and unnecessary
alarm dialouts.
5.4.2 Disabling Alarm Response to High or
Low Temperature
To disable alarm response to either high or low temperature
settings exclusively, enter the maximum temperature limit when
programming the selected input. (The OMA-P1104 will not
respond to temperatures encountered at maximum settings or
beyond.) Begin by following the key sequence shown in
Section 5.4.1, and when prompted to enter the high or low
temperature value:
• Set high temperature to either +150o F or +65o C (high
temperature limit) to prevent the OMA-P1104 from
responding to a high temperature alarm.
• Set low temperature to either -20o F or -30o C to prevent
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
the OMA-P1104 from responding to a low temperature
alarm.
5.4.3 Interrogating High and Low Temperature Limits
1. Press WHAT IS.
WHAT
IS
*
2. Press TEMP LIMITS.
5
TEMP LIMITS
3. Press the number key corresponding to the selected
temperature input.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
5.5 Temperature Scale
Temperature inputs may be set in either Fahrenheit or Celsius
degrees. The default temperature scale is Fahrenheit. To change
to Celsius:
1. Press SENSOR ON/OFF.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
2. Press TEMP. The OMA-P1104 responds: “Off,” indicating
Celsius scale has replaced Fahrenheit scale.
TEMP
F° / C°
3. To return to Fahrenheit scale, repeat the key sequence.
The OMA-P1104 responds: “On,” indicating Fahrenheit
scale is in effect.
NOTE
When switching from Fahrenheit to Celsius, or
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
vice versa, the change applies to all inputs
configured to read temperature. When switching
temperature scales it is important to reset high
and low temperature limits on all temperature
inputs. Refer to Section 5.4.1 to reset
temperature limits.
5.6 Temperature Calibration
To compensate for minor variances in sensor accuracy, an offset
may be programmed for each temperature input. The amount of
offset is measured in degrees Fahrenheit or degrees Celsius.
Adjustments are possible within a range from -10 degrees to
+10 degrees. For example, if input 3 is sensing temperature and
is reading 1 degree too high, then the calibration for input 3 is
set at -1 to obtain an accurate reading.
5.6.1 Programming Temperature Calibration
1. Press SET.
SET
#
2. Press CALIBRATE.
6
CALIBRATE
3. Press the number (1 to 4) of the selected temperature
input to be calibrated.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
4. Enter the number required to offset the current tempera-
ture reading so a correct reading is obtained.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
• To program a positive offset number (up to +10
degrees), enter the number on the keypad. The
OMA-P1104 recites the digits as they are pressed.
• To program a negative offset number (up to –10
degrees), first press PAUSE. The unit responds with a
“beep.” Next, enter the number on the keypad. The unit
recites the digits as they are pressed.
5. Press ENTER. The OMA-P1104 responds:“Enter.”
ENTER
TONE
PM
NOTE
If you find that your calibration offset exceeds
more than + 5 or – 5 degrees, other complicating
factors could be affecting normal operation of
the OMA-P1104. Call Omega for technical
assistance.
5.6.2 Interrogating Temperature Calibration
1. Press WHAT IS.
WHAT
IS
*
2. Press CALIBRATE.
6
CALIBRATE
3. Press the number key corresponding to the selected
temperature input.
1
2
3
CALL
DELAY
VOICE
REPS
INTERCALL
TIME
4
MAX CALLS
If a “beep” precedes the number as it is recited, then a
negative offset is indicated.
5.7 Obtaining Current Temperature
Current temperature readings for each temperature input may
be accessed at any time. The OMA-P1104 recites the input
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
number, and the actual temperature detected by the attached
sensor, for all inputs configured as temperature. To obtain
current temperature:
1. Press WHAT IS.
WHAT
IS
*
2. Press TEMP.
TEMP
F° / C°
5.8 AC Power Monitoring Enable/Disable
The OMA-P1104 monitors AC power failure. This command
enables or disables the power failure detection feature.When
enabled, the OMA-P1104 will monitor power and dial out when
AC power failure exceeds a programmable span of time (refer
to AC Power Failure Recognition Time, Section 5.9).
The default setting for AC power monitoring is enabled (on).
When disabled, the OMA-P1104 will not dial-out to report
power failure.
5.8.1 Enabling/Disabling the AC Power Alarm
1. Press SENSOR ON/OFF.
SENSOR
ON/OFF
2. Press POWER.
0
ID NUMBER
POWER
• The OMA-P1104 will say “Off” to indicate that the
power alarm is disabled, or
• The OMA-P1104 will say “On” to indicate that the
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
power alarm is enabled.
3. Repeat key sequence to change settings.
5.9 AC Power Failure Recognition Time
The AC Power Failure Recognition Time is the length of time
that AC electric power is off before a valid alarm is recognized
and dial-out begins. The default setting is 5 minutes, 0 seconds,
but is programmable from 0 seconds to a maximum of
272 minutes.
When AC power failure occurs, and throughout the pro-
grammed Recognition Time, the OMA-P1104 steadily repeats
the message, “the electricity is off,” at the unit’s installation site.
There is no Call Delay programming available for AC power
failure. Immediately following Recognition Time, the OMA-
P1104 begins the dial-out process to report power failure.
To cancel the power-failure message locally at the keypad
(during or after Recognition Time) press any key on the
OMA-P1104 keypad. This action also cancels the dial-out
process. The AC power failure alarm may also be cancelled
remotely, by telephone acknowledgment (see Chapter 6,
Section 6.1).
5.9.1 Programming Power Failure Recognition Time
1. Press SET.
SET
#
2. Press RECOGNITION TIME.
7
RECOGNITION
TIME
3. Press POWER. The OMA-P1104 responds: “Enter
minutes.”
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
0
ID NUMBER
POWER
4. Using the number keys, enter the number of minutes. The
OMA-P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER. The OMA-P1104 responds: “Enter
seconds.”
ENTER
TONE
PM
6. Using the number keys, enter the number of seconds. The
OMA-P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
7. Press ENTER. The OMA-P1104 responds: “OK.”
ENTER
TONE
PM
5.9.2 Interrogating Power Failure Recognition Time
1. Press WHAT IS.
WHAT
IS
*
2. Press RECOGNITION TIME.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
7
RECOGNITION
TIME
3. Press POWER.
The OMA-P1104 will recite the power Recognition Time.
0
ID NUMBER
POWER
5.10 Sound Alarm Monitoring
This feature allows you to program the level and duration of
sound that will cause the OMA-P1104 to respond to an alarm
and dial-out. It may be useful to desensitize the OMA-P1104 to
sound if it is installed in an area with a relatively high noise
level, or where a loud noise occurs frequently but is not
associated with an alarm. In some applications, it may be
desirable to increase sound sensitivity to low sound levels.
5.10.1 Programming Sound Alarm Sensitivity
The sensitivity setting for sound alarm monitoring ranges from
1 to 255. A value of 1 makes the microphone the MOST
sensitive to changes in sound. The value 255 makes the
microphone the LEAST sensitive to sound. The default value
is 32.
1. Press SET.
SET
#
2. Press CALIBRATE.
6
CALIBRATE
3. Press SOUND. The OMA-P1104 responds: “Enter
number.”
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
9
LISTEN TIME
SOUND
4. Using the number keys, enter a value for sound sensitivity.
The OMA-P1104 recites the digits as you press them.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER. The OMA-P1104 responds: “Enter.”
ENTER
TONE
PM
5.10.2 Interrogating Sound Sensitivity
1. Press WHAT IS.
WHAT
IS
*
2. Press CALIBRATE.
6
CALIBRATE
3. Press SOUND. The OMA-P1104 recites the programmed
sound sensitivity level.
9
LISTEN TIME
SOUND
5.10.3 Programming High Sound Alarm
Recognition Time
The Recognition Time for sound alarm monitoring ranges from
2 seconds to 59 seconds. The default value is 8 seconds.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
1. Press SET.
SET
#
2. Press RECOGNITION TIME.
7
RECOGNITION
TIME
3. Press SOUND. The OMA-P1104 responds: “Enter
seconds.”
9
LISTEN TIME
SOUND
4. Using the number keys, enter the number of seconds. The
OMA-P1104 will recite the digits as they are pressed.
1
2
3
INTERCALL
TIME
CALL
DELAY
VOICE
REPS
4
6
CALIBRATE
5
TEMP LIMITS
MAX CALLS
9
7
RECOGNITION
TIME
8
LISTEN TIME
SOUND
CLOCK
0
ID NUMBER
POWER
5. Press ENTER. The OMA-P1104 responds: “OK.”
ENTER
TONE
PM
5.11High Sound Alarm Enable/Disable
The OMA-P1104 monitors sound through the built-in
microphone. When the sound level suddenly exceeds the
programmed high sound limit, the OMA-P1104 will respond to
an alert condition. The increased sound level must continue
throughout the programmed recognition time. The default for
high sound alarm is enabled (on).
NOTE
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
The microphone is also used for listening to
on-site sounds. Refer to Chapter 4, Section 4.7.
Disabling the sound alarm does not affect
listen-in capability.
5.11.1 Changing Enabled/Disabled High Sound Alarm
1. Press SENSOR ON/OFF.
SENSOR
ON/OFF
2. Press SOUND. The OMA-P1104 will say “Off” to
indicate disabled or “On” to indicate enabled.
9
LISTEN TIME
SOUND
3. Repeat key sequence to change settings.
5.12 Exit Delay
When tripping an alarm is unavoidable, yet a true alert
condition has not actually occurred, the alarm response,
including dial-out, can be temporarily suppressed.
The OMA-P1104 is able to suppress and then reset its dial-out
function automatically through use of the Status Report. This is
especially convenient when an alert condition is created upon
exiting a monitored door, and there is no way to cancel from
the local keypad.
Example: You are planning to exit through a monitored door.
Prior to exiting, you initiate a Status Report recitation at the
OMA-P1104 keypad by pressing WHAT IS, followed by
STATUS, (key sequence shown below). This allows you
approximately 30 seconds to exit without activating the
OMA-P1104’s programmed response to an alarm. At the
conclusion of the status report, normal alarm response is
reactivated.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Alarm Programming
To use exit delay, initiate the Status Report.
1. Press WHAT IS.
WHAT
IS
*
2. Press STATUS. The OMA-P1104 recites the full Status
Report; during this time, you are able to exit the
monitored area without tripping an alarm.
STATUS
CONFIGURE
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
NOTES
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Acknowledgment,
Status Report, and
Remote Access
In addition to communication and alarm monitoring
capabilities, the OMA-P1104 will also respond to your
instructions and provide you with access to information on
monitored conditions at all times.
By issuing commands to the unit, either at the installation site
or over standard telephone lines, the following features may be
activated:
• Acknowledgment of existing alarms
• The Status Report on all monitored conditions.
6.1 Alarm Acknowledgment
When the OMA-P1104 dials out with an alarm message, it will
request acknowledgment before hanging up. Acknowledgment
indicates to the unit that the alarm message has been received.
Upon acknowledgment, the OMA-P1104 will cancel the dial-
out sequence.
There are three ways* that an alarm is acknowledged directly:
• Local Acknowledgment
• Touch-ToneTM Acknowledgment
• Callback Acknowledgment
* A fourth method of alarm acknowledgment is indirect. Refer
to Max Calls, Chapter 4, Section 4.12 for an example of
automatic alarm acknowledgment.
6.1.1 Local Acknowledgment
To acknowledge an alarm locally (directly at the installation
site of the OMA-P1104), press any key.
6.1.2 Touch-ToneTM Acknowledgment
This method of remote alarm acknowledgment works with a
Touch-ToneTM telephone.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
Example: You receive a call from the OMA-P1104, reporting
that an alarm exists. The message concludes: “Indicate you
have received warning message.” Now, or at any time during
this call, you may acknowledge the alarm with the code “555”
if you are using a Touch-ToneTM telephone.
• To enter “555,” press the number (5) key on the Touch-
ToneTM phone keypad three times. The OMA-P1104 will
respond: * “Warning message received by telephone
number (last number dialed).” The OMA-P1104 will
hang up and the dial-out sequence, including any further
response to the alarm, will be cancelled.
• If you enter the wrong code or do not enter it within
10 seconds following the conclusion of the message, the
OMA-P1104 will respond: “Dial telephone number
(the programmed unit phone number) within (Intercall
Time).” Then, the OMA-P1104 will hang up. The alarm
is still not acknowledged until you call back. You have a
period equal to the programmed Intercall Time to call
the unit back2( 9dntero(y ackno138.4(wledge the alar)-19.5. Refther)]T
70
Chapter 6:Acknowledgment, Status Report, and Remote Access
NOTE
If you have the TAD feature ( telephone
answering device) enabled, the OMA-P1104 will
answer the telephone on the first ring. If it is
disabled, the telephone must be allowed to ring
10 times. This serves as a precaution against a
random alarm acknowledgment. Refer to
Chapter 4, Section 4.6, for complete information
on using the TAD feature.
6.2 Status Report
The Status Report allows access to complete information on all
monitored conditions either locally, from the keypad, or by
telephone, from any location. The OMA-P1104 will answer an
incoming telephone call following the programmed Rings Until
Answer (refer to Chapter 4, Section 4.5). Included with the
Status Report are messages related to alarm conditions,
AC power, battery backup and sound level. It also provides an
opportunity for listening to on-site sounds (refer to Listen-in
Time, Chapter 4, Section 4.7).
To initiate the Status Report:
1. Press WHAT IS.
WHAT
IS
*
2. Press STATUS.
STATUS
CONFIGURE
Sections 6.2.1, 6.2.2, and 6.2.3 demonstrate two different Status
Report recitations. The Status Report starts with:
“Hello. This is telephone number 555-1234 (or the
programmed ID).”
“The time is 12:15 PM (or the current time).”
The OMA-P1104 proceeds with a separate report for each
input. Each input identifies itself by reciting the input number.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
6.2.1 Example: Status Report, No Alarms
Inputs 2, 3, and 4 are configured as dry contact and input 1 is
configured as temperature. No alarms exist. The Status Report
begins by saying, “Hello, this is telephone number 555-1234;
the time is 12:15 PM.” Following this introduction, the report
continues:
“Number 1, 74 degrees, OK.”
“Number 2, OK.”
“Number 3, OK.”
“Number 4, OK.”
“The electricity is ON.” This refers to AC power.
“Battery condition, OK.” Other responses: “Battery condition
low” or “Replace batteries.” (Refer to Section 6.2.4 for
additional information regarding battery condition.)
“Sound level, OK.”
“Listen to the sound level for 10 seconds.” In this case, the
programmed Listen-in Time is set at 10 seconds. (This feature
is not available when obtaining the Status Report on-site,
directly at the keypad.)
The Status Report repeats once more and the OMA-P1104
concludes the call, saying: “Have a good day.” (The Status
Report will not repeat if obtained at the keypad; “Have a good
day,” is also not recited.)
The phrase “no number” at the end of a Status Report
indicates that no dial-out phone numbers have been
programmed.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6:Acknowledgment, Status Report, and Remote Access
6.2.2 Example: Status Report, Existing Alarms
Inputs 2, 3,and 4 are configured as dry contact and input 1 is
configured as temperature. An emergency situation is at hand:
a fire in a greenhouse has tripped a smoke alarm and electrical
power has been disrupted. In addition to high sound and AC
power alarms, separate alarms exist on inputs 1, 2, 3, and 4. You
happen to call in for the Status Report, which begins with,
“Hello, this is telephone number 555-1234; the time is
12:15 PM.” Following this introduction, the report continues:
“Number 1, 110 degrees, HIGH.”
“Number 2, EXISTS.”
“Number 3, EXISTS.”
“Number 4, EXISTS.”
“The electricity is OFF.”
“Battery condition, OK.”
“Sound level, HIGH.”
“Warning message received by ...(last telephone number
dialed*).”
“Listen to the sound level for 10 seconds.”
The Status Report repeats once more and the OMA-P1104
concludes the call, saying: “Have a good day.”
* The “last telephone number dialed” refers to any one of the
programmed, dial-out telephone numbers through which the
OMA-P1104 was able to receive alarm acknowledgment, prior
to your call for a Status Report; this could also refer to the
OMA-P1104’s I.D. Number (identification number), if the
alarms are acknowledged at the keypad by someone present at
the site.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
6.2.3 Example: Status Report, Disabled Inputs
If an input is disabled, the dial-out feature for that input is
deactivated, but all other programmed parameters remain in
effect. In the example below, all 4 inputs are disabled, although
inputs 1 and 3 are detecting alarms. AC power and Sound Level
is also disabled for dial-out. (Note that to indicate disabled
status, only AC power will return two audible “beeps,” rather
than the word “OFF.”) When you call the OMA-P1104 for a
Status Report, you hear the following:
“Hello, this is telephone number 555-1234.
“The time is 12:15 PM.”
“Number 1, OFF, 96 degrees, HIGH.”
“Number 2, OFF, 74 degrees, OK.”
“Number 3, OFF, EXISTS.”
“Number 4, OFF, OK.”
“The electricity is (beep, beep), ON.” If the electricity is off,
or the AC adaptor is disconnected, you will hear:
“The electricity is (beep, beep), OFF.”
“Battery condition, OK.”
“Sound level, OFF, OK.” If the sound level is high you will
hear: “Sound level, OFF, HIGH.”
“Listen to the sound level for 10 seconds.”
The Status Report repeats once more and the OMA-P1104
concludes the call, saying: “Have a good day.”
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6:Acknowledgment, Status Report, and Remote Access
6.2.4 Battery Condition
During a Status Report, you may hear one of three possible
messages regarding battery power. The OMA-P1104
determines the appropriate message by measuring battery
voltage. Depending upon the remaining voltage, it may
respond:
• “Battery Condition , OK,” if over 8.2 Volts.
• “Battery Condition , low,” if between 7.2 and 8.2 Volts.
• “Replace batteries,” if below 7.2 Volts.
6.2.5 Remote Access by Touch-Tone™ Telephone
Calling the OMA-P1104 for a Status Report provides the
opportunity to access other functions, using Touch Tone™ push-
button commands. Remote telephone commands include:
• Disabling/enabling any input.
• Disabling/enabling High Sound Alarm monitoring.
• Disabling/enabling AC Power monitoring.
• Activation of Listen-In Time.
• Activation of the Status Report.
To issue commands by telephone, first dial the number of the
OMA-P1104 to access the Status Report. The Status Report
will be followed by the programmed Listen-In Time. If you
remain on the telephone, the Status Report will be repeated,
followed by a 10 second waiting period and hang-up. During
this
10 second waiting period, or at any time during the call, other
commands may by accessed by pressing any push button on
the telephone.
If a Security Code is in effect, the OMA-P1104 will prompt
you with: “Enter Security Code.” If no Security Code is set,
then it will say “O.K.”
• Enter your Security Code (4 digits) with the telephone
push buttons. If the code you enter is correct, the
OMA-P1104 will respond: “OK.”
• If you enter the wrong Security Code, the OMA-P1104
says,“Error. Have a good day,” and hangs up.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
Disabling/enabling inputs – If an input is set to detect an alert
condition, it can be disabled to prevent the OMA-P1104 from
dialing out, or re-enabled at any time.
This feature allows the convenience of disabling an input, even
if you are away from the site of the OMA-P1104. One such
application may involve an input programmed to detect
unauthorized entry. You are in another locale, but must allow
someone else temporary access to the area monitored by the
OMA-P1104. Using a Touch ToneTM telephone, you can disable
the appropriate input (thereby disabling any alarm dial-out
response). The input remains disabled until you issue the same
command, which effectively returns it to its former, enabled
state.
Press the following push-buttons on the Touch ToneTM tele-
phone to execute the desired command:
* (asterisk), 1
...equal to Sensor On/Off, for input 1. To re-enable the
input, repeat the same Touch-ToneTM button sequence
used for disabling.
* (asterisk), 2
...equal to Sensor On/Off for input 2, and so on, for
inputs up to 4. To re-enable the input, repeat the same
Touch-ToneTM button sequence used for disabling.
Disabling/enabling High Sound Monitoring –
* (asterisk), 9
...equal to SENSOR ON/OFF for High Sound Alarm
monitoring. To re-enable High Sound Alarm, repeat the
command.
Disabling/enabling AC Power –
* (asterisk), 0
...equal to Sensor On/Off for AC Power monitoring. To
re-enable AC Power monitoring , repeat the command.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6:Acknowledgment, Status Report, and Remote Access
Activating Listen-In Time –
#(pound), 1
...initiates Listen-In Time for listening to on-site sounds
for the programmed time available.
Activating Status Report –
#(pound), 2
...initiates a full recitation of the Status Report.
Exiting –
#(pound), #(pound)
...forces exit. The 1104 says, “Have a good day,” and
hangs up.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
NOTES
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A:Troubleshooting
In the event that a problem is encountered, this section will assist
you in determining the cause, so you can return the unit to its usual
monitoring routine with minimal interruption.
Most problems with the OMA-P1104 are easy to identify and
quickly corrected, and are found under the following general
headings:
• Communications/dial-out functions
• Temperature monitoring
• Sound level monitoring
• Other monitoring functions
If you have tried the solutions outlined in this section and are not
satisfied with the results, call Omega Customer Service.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Accessories
The sensors listed below are available from Omega, and
represent the most commonly used input devices. Other dry
contact sensors, designed for more specialized applications,
may also be used. Commercial or industrial electrical supply
houses can provide devices to monitor virtually any condition.
For further information, contact Omega’s Sales department at
1-800-82-66342 (1-800-TC-OMEGA).
MODEL NUMBER
OMA-PX05
SENSOR / SWITCH
Remote Temperature Sensor
Magnetic Reed Switch
Water Detection Sensor
Temp° Alert
OMA-PX06
OMA-PX13
OMA-PX22
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Omegaphone® OMA-P1104 User’s Manual
NOTES
88
Download from Www.Somanuals.com. All Manuals Search And Download.
|