Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for purchasing the OLYMPUS Electronic Flash (FL-36). Before use, please read this instruction manual to ensure your
safety, and keep it handy for future reference.
ꢀ
This electronic flash has been designed exclusively for use with Olympus digital cameras. Do not connect the electronic flash
to a camera not manufactured by Olympus, as this may result in a malfunction or damage to the camera and/or flash.
DANGER
SAFETY PRECAUTIONS (Be sure to read and observe the following.)
This instruction manual uses a variety of common symbols and icons to assist you in proper handling and usage of this product
properly, and to warn you of potential hazards to yourself and others as well as to property.These symbols and their significance
are described below.
ꢀ
ꢀ
ꢀ
The electronic flash incorporates high-voltage circuitry. Never attempt to disassemble or modify it, as this may
result in electric shock and/or injury.
Do not use the electronic flash in a place where it may be exposed to flammable or explosive gas. Otherwise, fire
ignition or explosion may result.
To prevent a traffic accident, do not direct the flash towards the driver of a car.
DANGER
WARNING
precautions indicated by this
symbol may result in injury
or death.
CAUTION
Failure to observe the
precautions indicated by this
symbol may result in injury or
property damage.
Failure to observe the
precautions indicated by this
symbol may result in serious
injury or death.
Failure to observe the
WARNING
ꢀ
Do not fire the flash or AF illuminator light immediately in front of a person’s eyes (particularly an infant). Exposure
to the light from the flash at a very short range may cause irreparable injury to the eyes. Be especially careful to
avoid using the electronic flash at a distance of less than 1 meter from an infant.
Symbols for prohibiting action
Symbol instructing action
ꢀ
Do not leave the electronic flash and batteries within reach of children.
• If a child swallows a battery or small accessory, see a doctor immediately.
• If the flash is emitted near a child, their eyes may be injured irreparably.
• Moving parts of the electronic flash could injure a child.
Disassembly
prohibited
Prohibited
Mandatory
For customers in Europe
ꢀ
Avoid the following actions to prevent fire or injury due to battery fluid leak, overheating, fire ignition or bursting.
• Do not use batteries that are not specified for use with this electronic flash.
• Do not throw the battery in a fire, expose it to heat, short-circuit it, or disassemble it.
• Do not mix old and new batteries, or batteries of different types or brands.
• Do not attempt to recharge non-rechargeable batteries such as alkaline batteries.
• Do not load batteries with the +/– polarity reversed.
The “CE” mark indicates that this product complies with the European requirements for safety, health, environment
and customer protection. CE-mark products are for sale in Europe.
For customers in USA
FCC Notice
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
ꢀ
ꢀ
ꢀ
Do not store the electronic flash in a place exposed to excessive dust or moisture. Otherwise, fire or electric shock
may result.
Any unauthorized changes or modifications to this equipment would void the user’s authority to operate.
For customers in CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Do not use the flash when it is covered by a flammable object such as a handkerchief.
Do not touch the light-emitting area after use. It will be very hot and could burn you.
If the electronic flash is dropped in water or any fluid gets inside, immediately remove the batteries and contact
your dealer or Olympus. Continued use could result in fire or electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
ꢀ
Do not touch the electric contacts of the electronic flash to prevent malfunction.
CAUTION
ꢀ
If you notice any abnormalities such as leakage, discoloration, deformation, overheating, or odor, stop using this de-
vice. Continued use could result in fire, overheating or explosion. Remove the batteries carefully to avoid burning
yourself and to prevent exposure to gas or dangerous fluids that may be released. For repair, contact Olympus.
ꢀ
To prevent overheating and deterioration of the light-emitting section, do not continue full activation more than 10
times in a row. After 10 successive operations, stop firing for a while until the light-emitting section cools down.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Always remove the batteries when you don’t expect to use the electronic flash for a long period. Otherwise, heat
generation or fluid leak from the batteries may result in fire, injury and/or contamination of the surroundings.
BATTERY PRECAUTIONS
ꢀ
Use only the specified batteries. (see page 14)
Do not use a leaking battery. Doing so could result in fire or electric shock. Please contact your dealer or Olympus.
■
Be sure to observe the following points. Otherwise, battery fluid leak, overheating, fire ignition and/or bursting may
result.
• Do not mix old and new batteries, recharged and discharged batteries, batteries of different capacities, or
batteries of different types or brands.
• Do not attempt to recharge non-rechargeable batteries such as alkaline batteries.
• Do not load or use the batteries with the +/– polarity reversed. If the batteries do not fit smoothly in the battery
compartment, do not force them.
• Never use a battery if its outer coating (insulation) has been partially or entirely peeled off. Otherwise, leakage,
overheating or explosion may result.
Do not handle the electronic flash with wet hands. Doing so could result in electric shock.
Do not leave the electronic flash in a place where it may be exposed to high temperatures. Otherwise, deterioration
of parts or fire may result.
Do not take out the batteries immediately after using the electronic flash continuously for a long period.
Otherwise, the hot batteries may cause burns.
Do not deform the battery compartment or allow any foreign objects to get inside.
• Some brand-new batteries may also have their outer coating (insulation) peeled off completely or partially.
Never use these batteries.
HANDLING PRECAUTIONS
ꢀ
The electronic flash is composed of precision electronic parts. Absolutely avoid using or storing the electronic flash
in the following places, as this may result in malfunction or failure.
■
■
Do not use the following kinds of batteries.
Outer coating (insu-
lation) is peeling or
has peeled off (even
if the battery is brand-
new).
The negative end is
flat (whether or not a
part of the negative
pole is covered by
the coating).
• Under direct sunlight, on a beach, etc.
• Anywhere exposed to high temperatures and humidity or rapid fluctuations in temperature and humidity.
The negative end is
slightly swollen and
is not covered by the
coating (insulation).
• Any place exposed to excessive sand, dust or dirt.
• Near an air conditioner or air humidifier.
• Any place subject to vibrations.
• Near a fire.
• Any place exposed to water or moisture.
• Inside an automobile.
All rechargeable batteries must be recharged using the specified battery charger, simultaneously and completely.
Be sure to read the battery and battery charger instruction manual.
ꢀ
Do not apply a strong vibration or shock to the electronic flash by dropping it or hitting it against something.
ꢀ
When the electronic flash has not been used for a long period, mold or moss may form. This can cause a
malfunction. To prevent this, it is recommended to check the operations before using the electronic flash after a
long period of storage.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Improper use of batteries may result in fluid leak, heat generation and/or damage. Sweat and oil smudges may
cause battery contact failure. To prevent this, remove any stain completely with a dry cloth and insert the batteries
by observing the +/– polarity.
Note on the cameras used with the Electronic Flash
●
The functions available from the electronic flash are limited with certain digital cameras. For details, please check the
Olympus website (http://www.olympusamerica.com/E1).
■
■
■
■
■
■
■
■
■
■
In general, battery performance will be temporarily reduced as the ambient temperature drops. When using batter-
ies in a cold place, keep them warm by keeping the electronic flash in cold protection gear or clothing.
Before reading this manual
If battery fluid gets on your skin or clothes, it may irritate your skin. Immediately rinse your skin or clothes with clean
water.
○
○
The information in this manual may be subject to change without notice.
This manual has been compiled as carefully as possible. However, if you have any questions or wish to report an error
or omission, please contact Olympus.
If battery fluid comes in contact with your eyes, blindness may result. Rinse your eyes with clean water without
rubbing them and see a doctor immediately.
○
○
○
○
Duplication of this manual in part or in whole without permission of Olympus is prohibited except for personal use.
Reproduction of the contents of this manual without permission of Olympus is strictly prohibited.
Olympus will not assume any liability for the damages, loss of profit or claims from any third party incurred due to
improper use of this product.
Olympus will not assume any liability for the damages and loss of profit related to the loss of image data due to a failure
of this product, servicing by a third party not designated by Olympus or any other reason.
Note that the quality of the pictures shot using this product differs from that of the pictures of ordinary film-based
cameras.
Do not apply a strong shock to a battery or throw it.
When traveling, it is a good idea to carry spare batteries with you. In some countries, it may be difficult to obtain
certain batteries.
Do not immerse batteries in water or expose to moisture including rain, seawater and animal urine.
If the +/– terminals of a battery are stained with sweat or oil smudges, contact failure may result. Clean the termi-
nals well with a dry cloth before using the batteries.
Trademark information
Do not throw a battery in fire or heat it.
All brand names and product names mentioned in this manual are the trademarks or registered trademarks of their respec-
tive owners.
When disposing of batteries, be sure to follow local regulations.
When disposing of a rechargeable battery, insulate the +/– terminals with pieces of tape and take them to your
nearest rechargeable battery recycling center.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE PACKAGE CONTENTS
CONTENTS
Selecting the control mode ................ 34
AUTO ................................................. 35
MANUAL ............................................ 37
• Other Operations ....................................... 39
Bounce Shooting ............................... 39
Close-up Flash................................... 41
Manual Switching of Firing angle (ZOOM) .................. 42
Using the Wide Panel ........................ 43
Various Flash Shooting Methods ....... 45
• Custom Setup ............................................ 47
• All Reset ..................................................... 50
• Continuous Firing ....................................... 51
• Guide Number (GN) List ............................ 52
• Warning Display List .................................. 55
• Q&A ........................................................... 58
• Main Specifications .................................... 61
Check that all parts and accessories are present.
If any item is missing or damaged, contact your dealer.
• Checking the Package Contents.................. 9
• Nomenclature............................................. 10
• Control Panel Indicators............................. 12
• Loading Batteries ....................................... 14
• Checking Batteries ..................................... 16
• Attaching to the Camera/Removing from
the Camera ................................................ 18
• Picture Shooting Using a Digital Camera
with Communication Capability ................. 20
Selecting the control mode.................. 20
TTL AUTO ........................................... 22
AUTO .................................................. 24
MANUAL ............................................. 27
FP TTL AUTO ...................................... 29
FP MANUAL........................................ 32
• Picture Shooting Using a Digital Camera
without Communication Capability ............ 34
• Electronic flash, main body
• Flash case
• Batteries must be purchased separately.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOMENCLATURE
Bounce lock release button
(left-right direction)(Page 40)
Wide panel (Page 43)
Bounce lock release button
(up-down direction)(Page 40)
AF illuminator light-emitting area
When the subject is dark or low-
contrast, the built-in AF illuminator
emits light to facilitate focusing.
The AF illuminator can also be
defeated. (Page 47)
• The AF illuminator only works
with the Olympus Four Thirds
System digital SLR camera. It
does not work with other cam-
eras.
Accessory shoe
Bounce up/down angle indices
(Page 40)
Bounce left/right angle indices
(Page 40)
M O D E b u t t o n
(Pages 21 & 34)
AUTO CHECK lamp
(Page 22)
Battery compartment cover
(Page 15)
Light-emitting
area
Control panel (Page 12)
Auto light receptor
LIGHT button
Press to light up the control
panel for about 15 sec.
The panel also lights under
control by a digital camera with
communication capability.
Charge lamp/Test button
(Page 16)
Lock pin (Page 18)
Select dial (Page 23)
Lock ring (Page 18)
Electric contact
(Page 18)
Power button
ZOOM button (Page 42)
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL INDICATORS
Control mode
FP emission
(Pages 29 & 32)
Light intensity adjustment
26 28 31 33)
(Pages 20 & 34) (Pages 23
,
,
,
&
FOUR THIRDS
(Page 47)
Notes on This Manual
• The indications on the control panel may differ from those shown in the illustra-
tion above depending on the setup of the electronic flash, the camera in use,
and the shooting conditions.
Wide panel warning
(Page 43)
Zoom mode
(Page 42)
For example, the firing angle (ZOOM) can be displayed in either of the following
modes.
Close-up flash
shooting (Page 41)
Zoom value
(Page 42)
ISO speed
(Page 25)
Lens iris (F)
(Page 47)
① FOUR THIRDS : Focal length of a Four Thirds System digital camera
Guide Number (GN)
(Pages 52 & 54)
② 135
: Focal length converted to an equivalent angle of view
on a 135 type (35 mm film) camera
Feet
(Page 47)
Meter
(Page 47)
The text in this manual employs the FOUR THIRDS display mode and puts value
in the 135 display mode inside parentheses, such as “(XX mm with 135)”. For the
selection of the display modes, see page 47 .
Setting display
(GN, ISO, F, light control range, optimum shooting
range, and light intensity adjustment value)
• To simplify explanation, this figure shows the panel with all indicators lit.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
13
How to load the batteries
LOADING BATTERIES
The batteries are available separately. Always use one of the following battery combinations.
• AA (R6) alkaline batteries (LR6 type)................................... x 2
• AA (R6) Ni-Cd batteries ....................................................... x 2
• AA (R6) Ni-Mh batteries ....................................................... x 2
• AA (R6) Ni-Mn batteries (ZR6 type) ..................................... x 2
• AA (R6) lithium batteries (FR6 type) .................................... x 2
• AA (R6) oxyride batteries (ZR6Y type) ................................. x 2
1. Open the battery compartment cover.
2. Insert the batteries with correct +/– polarity.
3. Close the battery compartment cover.
• Lithium battery pack (CR-V3 type) (Olympus LB-01) ........... x 1
• The AA (R6) manganese batteries cannot be used.
Recommended Batteries
The flash’s charging circuitry is optimized for use with the following batteries:
• AA (R6) Ni-Mh battery
• Lithium battery pack (CR-V3 type) (Olympus LB-01)
CR-V3
AA (R6) batteries
ꢀNotes
• Do not mix old and new batteries or batteries of different types together.
• Remove the batteries when the electronic flash is not going to be used for a long period.
• Carry spare batteries when traveling or when using the flash in cold areas.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀFlash Interval and Flash Count
CHECKING BATTERIES
The following table shows the flash intervals and flash counts for various batteries. Data is
based on using batteries all of the same type.
After loading the batteries, check the remaining battery capacity by turning the electronic flash on.
1. Press the Power button to turn the electronic flash on.
• The control panel lights up and battery charging starts.
Batteries used
Flash interval
Approx. 7.5 sec.
Approx. 6.5 sec.
Approx. 5.5 sec.
Approx. 6.5 sec.
Approx. 7.5 sec.
Approx. 6.5 sec.
Flash count
AA (R6) alkaline dry cell batteries (LR6 type)
AA (R6) Ni-Cd batteries (P3SPS type, 1000 mAh)
AA (R6) Ni-Mh batteries (HHR-3SPS type, 2230 mAh)
AA (R6) Oxyride batteries (ZR6Y type)
AA (R6) lithium batteries (FR6 type)
Approx. 140 times
Approx. 100 times
Approx. 200 times
Approx. 140 times
Approx. 260 times
Approx. 320 times
2. Ensure that the Charge lamp lights up.
• Replace the batteries if the time taken for the Charge lamp
to light up is longer than the values specified below.
Alkaline or Ni-Mn batteries:
30 sec.
Lithium, Ni-Cd, Oxyride or Ni-Mh batteries: 10 sec.
• If the Charge lamp and AUTO CHECK lamp blink alter-
nately, it means that the battery capacity is running low. In
this case, replace the batteries.
CR-V3 lithium battery packs (Olympus LB-01)
• The flash emission interval and count data were obtained from in-house tests at Olympus.
Memo: To perform test flash activation, press the Test button.
3. Press the Power button again to turn the electronic flash off.
Turn the electronic flash off in the following cases:
• Before mounting it on the camera or dismounting it from
the camera.
• When flash emission is not required.
• When not using the electronic flash.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
How to remove
ATTACHING TO THE CAMERA/REMOVING FROM THE CAMERA
Confirm that both the camera and electronic flash are off.
1. Loosen the lock ring completely, then slide the electronic
flash out of the hot shoe.
Attaching or removing the electronic flash while either the flash or the camera is on may result in malfunction.
How to attach
2. Attach the hot shoe cover to the camera.
1. Place the light-emitting section in the standard position
(horizontal, front). If it is in the locked position, press and
2. tRuernmtohveeBthoeunhcoet slohcokerecolevaesrefrboumttothne. camera.
• Store the hot shoe cover in the pocket located on the inner
3. Lsiodoesoefnththeefllaoschk rciansge. .
•
If the lock pin is in the out position, press it in by turning it all
the way in the opposite direction to [←LOCK] until it stops.
ꢀNotes
To use the electronic flash with a digital camera not equipped with hot shoe:
• If the camera has an external flash terminal, the electronic flash can be attached and connected using the flash
bracket and bracket cable (optional).
Lock pin
• The electronic flash cannot be used with a camera that is not equipped with a hot shoe or external flash terminal.
Electric contact
• Do not apply excessive force to the lock pin.
• Do not touch the electric contact with a finger or metallic object.
• Do not attach the electronic flash while the lock pin is in the out position.
Otherwise, malfunction may result.
4. Slide the electronic flash all the way into the hot shoe until
5. Titusrtnopthsewloitchkarincglicakl.l the way into the direction of [←LOCK]
until it stops.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE SHOOTING USING A DIGITAL CAMERA WITH COMMUNICATION CAPABILITY
Flash control
mode
Control panel
display
Ref.
Pages
Control operation
Main application
<Selecting the control mode>
Flash is controlled automatically
by performing pre-flash accord-
ing to the camera setup.
Usually use this mode with a
camera with communication
capability.
TTL AUTO
1. Turn the camera on.
22
24
27
Flash light intensity is controlled
according to the light detected
through the auto light receptor of
the flash and to the camera setup.
If the camera has communica-
tion capability, this mode can be
used only when the camera is
an AUTO-compatible model.
2. Turn the electronic flash on. The batteries are recharged
when the Charge lamp lights up.
AUTO
3. Press the Shutter button of the camera gently to start com-
munication of shooting information including ISO speed,
lens iris and shutter speed between the camera and elec-
tronic flash.
Flash is performed according to
the manually set guide number
(GN).
Shooting using manual flash.
MANUAL
TTL AUTO and MANUAL modes
with Super FP emission that can
synchronize with the high-speed
shooting of the single-lens-reflex
focal plane shutter.
Outdoor shooting using flash,
such as sync shooting in the
daytime.
FP
TTL AUTO
4. Press the MODE button of the electronic flash to select
the flash control mode.
29 & 32
FP
MANUAL
• The selected flash control mode is shown in the control
panel.
Flash
control mode
• The mode is switched every time the MODE button is
pressed.
ꢀNotes
• Certain modes may be unavailable depending on the shooting mode set on the camera and the functions of the
camera in use.
• It is not possible to select an unavailable mode.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀLight intensity adjustment
The flash light intensity can be adjusted between +3 and –3.
<TTL AUTO>
In this mode, pre-flash is performed to measure the optimum flash intensity and then actual flash is
performed.
The light intensity adjustment must be set to ON in the
custom setup operation (page 47).
• The
indicator appears in the control panel.
TTL AUTO indicator
ZOOM indicator
Displayed according to the
focal length of the lens.
1. The control panel shows the light control range according
to the camera setup.
1. Turn the select dial to choose a light intensity adjustment value.
0 → +0.3 →+0.7→+1.0 ... +3.0
2. Confirm that the distance to the subject is within the light
control range.
0 → –0.3 → –0.7→ –1.0 ... –3.0
2. The display shows the light intensity adjustment value ex-
cept when the value is 0. In this case, the displayed light
control range corresponds to an adjustment value of 0.
If not, adjust the lens iris (F) or the subject distance.
The light control range varies according to the camera type
and camera setup (ISO speed, lens iris (F) and lens focal
distance (ZOOM)).
3. If the camera’s flash adjustment mode is selected, the
actual flash light intensity will be the total of the light
intensity adjustment value set on the FL-36 and that
set on the camera. The light intensity adjustment value
displayed is that of the FL-36 only.
Light intensity adjustment value
3. When flash activation has been performed correctly, the
AUTO CHECK lamp blinks for about 5 seconds after the
shutter is released.
Light control range
[Example]
Selected
Adjustment value
Actual light intensity
adjustment value displayed on FL-36 adjustment
FL-36
+0.3
+0.3
+0.6
Camera
+0.3
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ`çãÄáå~íáçåë=çÑ=fpl=ëéÉÉÇë=~åÇ=äÉåë=áêáëÉë
Åçåíêçää~ÄäÉ=áå=^rql=ãçÇÉ
<AUTO>
In this mode, the flash light intensity is controlled automatically according to the lens iris (F) setting and
the amount of light input to the auto light receptor.
ISO speed
3200 1600
800
F4
400
F2.8
F4
200
F2
100
F1.4
F2
50
25
F8
F5.6
F8
AUTO indicator
1. The control panel shows the light control range according
to the camera setup.
ZOOM indicator
Displayed according to the
focal distance of the lens.
F11
F16
F22
F32
F5.6
F8
F2.8
F4
F1.4
F2
F11
F16
F22
F32
F5.6
F8
F2.8
F4
F1.4
F2
The light control range is not displayed if the camera setup
(ISO speed and lens iris (F)) does not match one of the
usable ISO speed/lens iris (F) combinations.
In this case, the ISO and F indicators blink to alert you.
Change the camera setup (ISO speed and/or lens iris (F)).
(See page 55.)
F11
F16
F22
F32
F5.6
F8
F2.8
F4
F11
F16
F22
F32
F5.6
F8
F2.8
F4
F11
F16
F22
F32
F5.6
F8
F11
F16
F22
F5.6
F8
F11
F16
F11
3. When flash activation has been performed correctly, the
AUTO CHECK lamp blinks for about 5 seconds after the
shutter is released.
2. Confirm that the distance to the subject is within the light
control range.
If not, adjust the lens iris (F) or the subject distance.
The light control range varies according to the camera
setup (ISO speed, lens iris (F) and lens focal length
(ZOOM)).
Light control range
Memo: Test flash activation
Flash activation can be tested before actually releasing the shutter.
Press the Test button for test flash activation.
The light control is OK when the AUTO CHECK lamp blinks for about 5 seconds
after the test flash activation.
If the lamp does not blink, change the lens iris (F), ISO speed, subject distance, etc.
•
The light check by means of test flash activation is possible only in the AUTO mode.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀLight intensity adjustment
<MANUAL>
The flash light intensity can be adjusted between +3 and –3.
In this mode, the flash is emitted according to the guide number (GN) setting.
The light intensity adjustment must be set to ON in the
custom setup operation (page 47).
MANUAL indicator ZOOM indicator
1. The control panel shows the current guide number (GN)
• The
indicator appears in the control panel.
Displayed according to the
focal distance of the lens.
together with the optimum shooting distance according to
the camera setup.
1. Turn the select dial to choose a light intensity adjustment value.
0 → +0.3 →+0.7→+1.0 ... +3.0
0 → –0.3 → –0.7→ –1.0 ... –3.0
2. Turn the select dial to set the guide number (GN).
Set the guide number (GN) so that the optimum shooting
distance is equal to the subject distance.
2. The display shows the light intensity adjustment value ex-
cept when the value is 0. In this case, the displayed light
control range corresponds to an adjustment value of 0.
When the optimum shooting distance is 0.6 m (0.5 m in
case of close-up flash) or less, the displayed figure blinks
to warn that the subject is located outside the flash light
emission area.
Optimum shooting distance varies according to the cam-
era settings (ISO speed, lens iris (F) and lens focal dis-
tance (ZOOM)). See page 52 for details.
3. If the camera’s flash adjustment mode is selected, the
actual flash light intensity will be the total of the light
intensity adjustment value set on the FL-36 and that
set on the camera. The light intensity adjustment value
displayed is that of the FL-36 only.
Light intensity adjustment value
[Example]
Guide number (GN)
Selected
Adjustment value
Actual light intensity
Memo: Assuming that the ISO speed is 100, the optimum shoot-
ing distance can be calculated with the following formula.
Optimum shooting distance = Guide number (GN)/Lens iris (F)
(See page 54.)
adjustment value displayed on FL-36 adjustment
Optimum shooting
distance
FL-36
+0.3
+0.3
+0.6
Camera
+0.3
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀLight intensity adjustment
<FP TTL AUTO>
The flash light intensity can be adjusted between +0.7 and –0.7.
• In this mode, the flash uses Super FP emission to synchronize with high shutter speeds.
For details on using the camera’s built-in flash, see “Various Flash Shooting Methods” on page 45.
The light intensity adjustment must be set to ON in the
custom setup operation (page 47).
•
The following operations are possible at high shutter speeds in this mode.
• Attenuation of shades when shooting a picture against the light.
• The
indicator appears in the control panel.
1. Turn the select dial to choose a light intensity adjustment value.
•
Outdoor portrait shooting using daytime sync shooting with the lens iris opened up to blur the background.
0 → +0.3 →+0.7
0 → –0.3 → –0.7
Without flash
With flash (FP TTL AUTO)
2. The display shows the light intensity adjustment value ex-
cept when the value is 0. In this case, the displayed guide
number (GN) and optimum shooting distance correspond
to an adjustment value of 0.
Shooting against
light
Light intensity adjustment value
3. Even if the camera’s flash adjustment mode is selected,
only the FL-36’s adjustment setting will work.The camera’s
setting will not work.
With lens iris adjusted
With lens iris open
[Example]
Portrait shooting
Selected
Adjustment value
Actual light intensity
adjustment value displayed on FL-36 adjustment
FL-36
+0.3
+0.3
+0.3
Camera
+0.3
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀLight intensity adjustment
The flash light intensity can be adjusted between +3 and –3.
ZOOM indicator
Displayed according to the
focal length of the lens.
FP TTL AUTO indicator
1. The control panel shows the light control range according
to the camera setup.
The light intensity adjustment must be set to ON in the
custom setup operation (page 47).
• The
indicator appears in the control panel.
2. Confirm that the distance to the subject is within the light
control range.
1. Turn the select dial to choose a light intensity adjustment value.
0 → +0.3 →+0.7→+1.0 ... +3.0
0 → –0.3 → –0.7→ –1.0 ... –3.0
If not, adjust the lens iris (F) or the subject distance.
The light control range varies according to the camera
setup (ISO speed, lens iris (F) and lens focal distance
(ZOOM). The light control range is smaller than that in the
TTL mode.
2. The display shows the light intensity adjustment value ex-
cept when the value is 0. In this case, the displayed light
control range corresponds to an adjustment value of 0.
3. If the camera’s flash adjustment mode is selected, the
actual flash light intensity will be the total of the light
intensity adjustment value set on the FL-36 and that
set on the camera. The light intensity adjustment value
displayed is that of the FL-36 only.
Light intensity adjustment value
3. When flash activation has been performed correctly, the
AUTO CHECK lamp blinks for about 5 seconds after the
shutter is released.
Light control range
[Example]
Selected
Adjustment value
Actual light intensity
adjustment value displayed on FL-36 adjustment
FL-36
+0.3
+0.3
+0.6
Camera
+0.3
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
<FP MANUAL>
ꢀLight intensity adjustment
The flash light intensity can be adjusted between +0.7 and –0.7.
In this mode, Super FP emission is performed at the set light intensity.
The light intensity adjustment must be set to ON in the
custom setup operation (page 47).
FP MANUAL indicator
ZOOM indicator
1. Turn the select dial to set the guide number (GN).Together
Displayed according to the
focal distance of the lens.
• The
indicator appears in the control panel.
with the optimum shooting distance according to the cam-
era setup.
1. Turn the select dial to choose a light intensity adjustment value.
0 → +0.3 →+0.7
0 → –0.3 → –0.7
2. Turn dial A to set the guide number (GN).
Set the guide number (GN) so that the optimum shooting
distance is equal to the subject distance.
2. The display shows the light intensity adjustment value ex-
cept when the value is 0. In this case, the displayed guide
number (GN) and optimum shooting distance correspond
to an adjustment value of 0.
When the optimum shooting distance is 0.6 m (0.5 m in
case of close-up flash) or less, the displayed figure blinks
to warn that the subject is located outside the flash light
emission area. (see page 55.)
The optimum shooting distance varies according to the
camera setup (ISO speed, lens iris (F), lens focal length
(ZOOM) and shutter speed). See page 54 for details.
Light intensity adjustment value
3. Even if the camera’s flash adjustment mode is selected,
only the FL-36’s adjustment setting will work.The camera’s
setting will not work.
[Example]
Guide number (GN)
Optimum shooting distance
Memo: The optimum shooting distance can be calculated with the
following formula.
Selected
Adjustment value
Actual light intensity
adjustment value displayed on FL-36 adjustment
Optimum shooting distance = Guide number (GN)/Lens iris (F)
FL-36
+0.3
+0.3
+0.3
Camera
+0.3
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
<AUTO>
PICTURE SHOOTING USING A DIGITAL CAMERA WITHOUT COMMUNICATION CAPABILITY
In this mode, the flash light intensity is controlled automatically according to the lens iris (F) setting.
<Selecting the control mode>
ISO speed
AUTO indicator MZOOM indicator
1. Adjust Zoom according to the focal length of the lens.
2. While keeping the MODE button pressed, turn the select dial within
1. Turn the electronic flash on. The batteries are recharged
when the Charge lamp lights up.
2 seconds to set the ISO speed.
Note: If the MODE button is kept pressed for more than 2 seconds,
3. TthuernflatshhemsoedleeccthdainagleasctcootrhdeinCgustotomtheSeletunpsmiroisde(F(s)e.e page 47).
If the camera setup (ISO speed and lens iris (F)) does not
match one of the usable ISO speed/lens iris (F) combina-
tions, the ISO and F indicators blink to alert you. In this case,
change the camera setup (ISO speed and/or lens iris (F)).
2. Press the MODE button to select the flash control mode.
• The selected mode is shown in the control panel.
• The mode is switched every time the MODE button is
pressed.
4.When flash activation has been performed correctly,
the AUTO CHECK lamp blinks for about 5 seconds
after the shutter is released.
Lens iris (F)
Flash control
mode
Control panel
display
Ref.
Pages
Memo: By selecting an ISO speed and lens iris (F) different from those
set on the camera, the light intensity can be adjusted in 1/3 steps.
Control operation
Main application
Flash light intensity is controlled
according to the light detected
through the auto light receptor of
the flash and to the lens iris (F).
Usually use this mode.
AUTO
Memo: Test flash activation
35
37
Flash activation can be tested before actually releasing the shutter.
Press the Test button for test flash activation.
The light control is OK when the AUTO CHECK lamp blinks for about 5 seconds after
the test flash activation.
If the lamp does not blink, change the lens iris (F), ISO speed, subject distance, etc.
Flash activation is performed
according to the manually set
guide number (GN).
Shooting using manual flash.
MANUAL
•
The light check by means of test flash activation is possible only in the AUTO mode.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
<MANUAL>
In this mode, the flash is emitted according to the guide number (GN) setting.
ꢀLight control range in AUTO mode
AUTO light control range (m)
Firing angle (mm) Upper row: FOUR THIRDS. Lower row: 135
Guide number (GN)
MANUAL indicator
1. The control panel shows the current guide number (GN).
ISO speed
8(W panel) 10(W panel)
16(W panel) 20(W panel)
12
24
14
28
17
35
25
50
35
70
42
85
3200 1600 800 400 200 100 50 25
F8 F5.6 F4
F2.8 F2
F1.4
0.8 - 8.6
0.6 - 6.0
0.9 - 10.0 1.3 - 14.3 1.4 - 15.7 1.5 - 17.1 1.8 - 20.0 2.0 - 22.9 2.3 - 25.7
0.6 - 7.0 0.9 - 10.0 1.0 - 11.0 1.1 - 12.0 1.3 - 14.0 1.4 - 16.0 1.6 - 18.0
2. Adjust the MZOOM indicator according to the focal length
of the lens.
F11 F8
F5.6 F4 F2.8 F2
F1.4
F16 F11 F8
F5.6 F4 F2.8 F2 F1.4 0.5 - 4.3
F5.6 F4 F2.8 F2 0.5 - 3.0
F32 F22 F16 F11 F8 F5.6 F4 F2.8 0.5 - 2.1
F32 F22 F16 F11 F8 F5.6 F4
F32 F22 F16 F11 F8 F5.6 0.5 - 1.1
0.5 - 5.0
0.5 - 3.5
0.5 - 2.5
0.5 - 1.8
0.5 - 1.3
0.5 - 0.9
0.5 - 0.6
0.6 - 7.1
0.5 - 5.0
0.5 - 3.6
0.5 - 2.5
0.5 - 1.8
0.5 - 1.3
0.5 - 0.9
0.7 - 7.9
0.5 - 5.5
0.5 - 3.9
0.5 - 2.8
0.5 - 2.0
0.5 - 1.4
0.5 - 1.0
0.8 - 8.6 0.9 - 10.0 1.0 - 11.4 1.1 - 12.9
F22 F16 F11 F8
0.5 - 6.0
0.5 - 4.3
0.5 - 3.0
0.5 - 2.2
0.5 - 1.5
0.5 - 1.1
0.6 - 7.0
0.5 - 5.0
0.5 - 3.5
0.5 - 2.5
0.5 - 1.8
0.5 - 1.3
0.7 - 8.0
0.5 - 5.7
0.5 - 4.0
0.5 - 2.9
0.5 - 2.0
0.5 - 1.5
0.8 - 9.0
0.6 - 6.4
0.5 - 4.5
0.5 - 3.3
0.5 - 2.3
0.5 - 1.6
3. Turn the select dial to set the guide number (GN).
0.5 - 1.5
F32 F22 F16 F11 F8
0.5 - 0.8
0.5 - 0.5
F32 F22 F16 F11
MZOOM indicator
Light intensity ratio
The above table shows the light control ranges in the off-flash condition.
In the Custom Setup mode, the flash intensity can be dis-
played in a light intensity ratio instead of the guide number
(see page 49).
The displayed nearer value is 0.6 or more when the light emission section faces the front and 0.5
or more when it faces downward.
Light intensity ratio: Ratio of emitted light intensity with
respect to the intensity at full emission.
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
How to determine the lens iris (F), guide number (GN) and shooting distance
OTHER OPERATIONS
Bounce Shooting
1. When the shooting distance and lens iris are already determined:
Determine the guide number (GN) with the following formula and set the GN on the FL-36.
Bounce shooting refers to a method in which the light from the flash is bounced off the ceiling or walls.
This allows the light to go all around the subject, resulting in a soft picture without harsh contrast
or shadow.
Lens iris (F) x Shooting distance (m)
Guide number (GN) =
ISO speed coefficient
Shooting without bounce
Bounce shooting
2.When it is necessary to determine the lens iris (F):
Determine the lens iris (F) with the following formula and set F on the FL-36.
Guide number (GN) x ISO speed coefficient
Lens iris (F) =
Shooting distance (m)
3.When it is necessary to determine the optimum shooting distance:
Guide number (GN) x ISO speed coefficient
Optimum shooting
distance (m)
=
Lens iris (F)
ISO speeds and their coefficients
ISO speed
25
50
100
1.0
200
1.4
400
2.0
800 1600 3200
2.8 4.0 5.6
Coefficient 0.5
0.71
See page 52 for the guide number list.
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Close-up Flash
90˚
The flash activation area is inaccurate when the subject distance is between 0.5 and 1.0 m. In this case,
tilt the flash down.
1. While holding the Bounce lock release button, revolve the
light-emitting section in the up-down and left-right direc-
tions.
7˚
180˚
1. While keeping the Bounce lock button pressed, tilt the flash
down (7°)
2. The close-up flash indicator lights in the control panel.
The light-emitting section can be revolved in the range
shown in the figure on the left.
90˚
Down: 7°
(See “Close-up Flash” on page 41.)
Bounce lock release button
(up-down direction)
If the position of the light-emitting section is locked, press
and hold the Bounce lock release button and then change
the position.
Close-up flash indicator
Bounce lock release button
(left-right direction)
Available shooting range
(0.5～1.0m)
• The light control range and optimum shooting distance are not displayed in the control panel.
• The color of the surface (ceiling and/or walls) off which the light is bounced will affect the
pictures you take. Whenever possible, bounce the light off a neutral surface.
• When the firing angle adjustment is automatic (ZOOM), the ZOOM display on the control
panel shows “- -” and the firing angle is set to 25 mm (50 mm with 135 type).
• When the firing angle adjustment is based on manual switching (M ZOOM), the firing angle
can be varied manually (see page 42).
• The recommended range for this flash is 0.5 to 1.0 m.
•
•
The available shooting range is displayed on the control panel. The maximum shooting distance is 2.5 m.
The flash light may be blocked when the lens is long or large in diameter. Be sure to perform test shooting.
• Do not tilt the flash down in normal shooting. This will darken the upper part of the image.
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Switching of Firing angle (ZOOM)
Using the Wide Panel
The firing angle can be adjusted manually.
Use the built-in wide panel in flash shooting when the lens focal length is set to a wider position than 12 mm.
MZOOM indicator
1. Press the ZOOM button to adjust the firing angle.
• The M ZOOM indicator lights in the control panel.
• The firing angle can be set to one of 12, 14, 17, 25, 35 and
42 mm (24, 28, 35, 50, 70 and 85 mm with 135 type).
Each press of the ZOOM button switches the firing angle as
follows.
1. When the lens focal length is shorter than 12 mm (24 mm
with the 135 type), the wide panel warming indicator lights
in the control panel.
(This does not occur if the camera is not equipped with
communication capability.)
• The ZOOM indicator lights in AUTO ZOOM mode.
AUTO
12
14
(28)
17
(35)
25
(50)
35
(70)
42
(85)
ZOOM (24)
When the wide panel is used: (see page 43)
AUTO
10
8
(16)
2. Slide out the wide panel and place it on the light-emitting area.
• The wide panel indicator lights in the control panel.
ZOOM (20)
• AUTO ZOOM can be selected only when the camera in
use is equipped with the communication capability.
ꢀNote
Selecting a ZOOM value larger than your lens’s focal length will darken
the peripheral areas of the image.
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Wide panel indicator
Various Flash Shooting Methods
3. Press the ZOOM button to select the firing angle from 8
mm and 10 mm (16 mm and 20 mm with the 135 type).
The following flash shooting methods are possible according to the camera setup.
• Some flash shooting methods may be unavailable depending on the function and design of the
camera.
• For details on operating procedure, refer to the instruction manual for your camera.
1. Red eye-reduction flash
Reduces the appearance of
red eyes due to flash emis-
sion.
• When the wide panel is used, the actual guide number
(GN) will be lower than set. In the TTL AUTO, AUTO and
FP TTL AUTO modes, this results in a reduction of the
available shooting range. In the MANUAL and FP MANUAL
modes, this results in a reduction of the optimum shooting
range.
2. Slow sync
The flash is emitted with
slow shutter.
This makes it possible to take
clear pictures of subjects
against a night background.
• Be sure to store the wide panel again after shooting.
• To prevent damage to the wide panel, do not flip it in the
upward direction.
• If the wide panel is damaged when it is slid out, the ZOOM
button will no longer be operable. If that happens, disable
the wide panel switch to restore operability (page 47).
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Background screen sync
CUSTOM SETUP
Slow shutter is used and the flash is emitted immediately
before the end of exposure period.
Custom setup allows each user to customize flash setup to suit his or her preferences.
This makes it possible to take pictures of moving objects
such as car taillights with a streaming effect.
Setup procedure
1. Turn the electronic flash on.
2. Press and hold the MODE button for more than 2 sec-
onds, until the setup mode display appears in the control
panel.
4. Combination with camera’s built-in flash
When the camera in use has a built-in flash, it can be used
simultaneously with the electronic flash.
•
Advanced shooting techniques are possible. For example, you
can bounce the light from the electronic flash off the wall or ceil-
ing while using the camera’s built-in flash for a catch-light effect.
3. Press the MODE button momentarily to select the setup
mode.
• With certain camera models, the built-in flash may be disabled
when the electronic flash is mounted on the camera’s hot shoe.
4. TTurn the select dial to select the value.
5. Keep the MODE button pressed for more than 2 seconds
to exit from setup and return to the previous control panel
display.
ꢀNote
The electronic flash control mode should be set to TTL AUTO or
FP TTL AUTO.
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode display
Dial A
Value display
Dial B
Mode display
Dial A
Value display
Dial B
Setup mode
Function
Default
Setup mode
Wide panel
Function
Default
on
AF illuminator
The wide panel switch is activated. Use
this setting to detect that the wide panel
has been slid out.
AF illuminator is activated according to the
control from the camera.
switch disabling
Only works with the
Olympus Four Thirds
System digital SLR
camera. It does not work
with other cameras.
A
The wide panel switch is deactivated. Use
this setting when the wide panel is dam-
aged so that the firing angle can be
changed with the ZOOM button.
AF illuminator is defeated.
Use this setting when not using the flash
cable (clipping on to the hot shoe).
Flash cable
GN (guide number)
indicator
The flash intensity is displayed in a GN
(guide number).
on
Use this setting when using the flash cable
(off flash cable).
on
on
The flash intensity is displayed in a light
intensity ratio.
Firing angle
(ZOOM) display
Firing angle (ZOOM) is displayed in terms
of the lens focal length of a FOUR
THIRDS digital camera.
ISO and F communi-
cation in AUTO mode
Only works with a
camera with ISO
speed setting com-
munication capability
in AUTO mode.
The ISO speed and lens iris (F) are auto-
matically set by the camera side.
Firing angle (ZOOM) is converted into the fo-
cal distance of the 135 type. This allows the
flash to be used in the same feeling as the
flash for a 135 type (35 mm film) camera.
4-3
The ISO speed and lens iris (F) can be
set with the select dial.
Distance display
unit
Distance is displayed in meters.
Distance is displayed in feet.
m
Light intensity
adjustment
Light intensity cannot be adjusted.
Light intensity can be adjusted.
OFF
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode display
Dial A
Value display
Dial B
CONTINUOUS FIRING
Setup mode
Function
Default
Continuous firings make the light-emitting section hot and may cause it to deteriorate or malfunction.
Therefore, continuous firing should be limited to the counts shown in the following table. Always
leave the electronic flash unused for at least 10 minutes after continuous firing up to the limit count.
ISO speed selection in
AUTO mode
Works with a camera with-
out ISO speed setting com-
munication capability in
AUTO mode. Also works
The ISO speed can be set with the select
dial.
ꢀLimit counts of continuous firings
Flash control mode
Light intensity ratio
Flash interval
6 sec.
Limit count
100
TTL AUTO
AUTO
1/1
1/2
10
20
40
80
with
a
camera with ISO
speed setting communica-
tion capability in AUTO
mode when the ISO and F
communication in AUTO
mode is set to OFF.
3 sec.
MANUAL
FP AUTO
FP MANUAL
1/4
1 sec.
1/8 to a/128
0.5 sec. or less
ALL RESET
All Reset resets the custom setups to the factory default settings.
• Press the MODE and LIGHT buttons simultaneously for 2
or more seconds to reset the custom setups (except for
the distance display unit (m/ft)) to the default settings.
• The distance display unit (m/ft) is not altered by the all
reset operation.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
GUIDE NUMBER (GN) LIST
• FP TTL AUTO
ISO100, m
42
FOUR THIRDS
8
10
12
24
14
28
17
35
25
50
35
70
• TTL AUTO/AUTO
ZOOM (mm)
ISO100, m
With 135
1/125
16
20
85
FOUR THIRDS
With 135
8
10
20
14
12
24
20
14
28
22
17
35
26
25
50
28
35
70
32
42
85
36
8.5
7.5
6.7
6.0
5.3
4.7
4.2
3.8
3.4
3.0
2.7
2.4
2.1
1.9
1.7
1.5
1.3
1.2
1.1
9.9
8.8
7.8
7.0
6.2
5.5
4.9
4.4
3.9
3.5
3.1
2.8
2.5
2.2
2.0
1.8
1.6
1.4
1.2
14.1
12.5
11.2
10.0
8.8
7.9
7.1
6.3
5.6
5.0
4.5
4.0
3.5
3.2
2.8
2.5
2.2
2.0
1.8
15.6
13.8
12.3
11.0
9.7
8.7
7.8
6.9
6.1
5.5
4.9
4.3
3.9
3.5
3.1
2.8
2.5
2.2
1.9
17.0
15.0
13.4
12.0
10.6
9.5
8.5
7.5
6.7
6.0
5.4
4.7
4.2
3.8
3.4
3.0
2.7
2.4
2.1
19.8
17.5
15.7
14.0
12.4
11.1
9.9
22.6
20.0
17.9
16.0
14.1
12.6
11.3
10.0
8.9
25.5
22.5
20.1
18.0
15.9
14.2
12.7
11.3
10.1
9.0
ZOOM (mm)
16
12
1/160
TTL AUTO/AUTO
Full emission
1/200
1/250
1/320
• MANUAL
1/400
ISO100, m
42
1/500
FOUR THIRDS
8
10
20
12
24
14
28
17
35
25
50
35
70
ZOOM (mm)
1/640
8.8
With 135
1/1
16
85
1/800
7.8
12.0
8.5
6.0
4.2
3.0
2.1
1.5
1.1
14.0
9.9
7.0
4.9
3.5
2.5
1.8
1.2
20.0
14.1
10.0
7.1
22.0
15.6
11.0
7.8
24.0
17.0
12.0
8.5
28.0
19.8
14.0
9.9
32.0
22.6
16.0
11.3
8.0
36.0
25.5
18.0
12.7
9.0
Shutter speed
1/1000
1/1250
1/1600
1/2000
1/2500
1/3200
1/4000
1/5000
1/6400
1/8000
7.0
8.0
1/2
6.3
7.2
8.0
1/4
5.5
6.3
7.1
MANUAL
Light intensity ratio
1/8
4.9
5.7
6.4
1/16
1/32
1/64
1/128
5.0
5.5
6.0
7.0
4.4
5.1
5.7
3.5
3.9
4.2
4.9
5.7
6.4
3.9
4.5
5.0
2.5
2.8
3.0
3.5
4.0
4.5
3.5
4.0
4.5
1.8
1.9
2.1
2.5
2.8
3.2
3.1
3.6
4.0
2.8
3.2
3.6
2.5
2.8
3.2
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
• FP MANUAL
WARNING DISPLAY LIST
The following guide number (GN) figures have a 1/1 light intensity ratio.
.
ISO100 m
• Digital camera with communication capability
FOUR THIRDS
With 135
1/125
8
10
20
12
24
14
28
17
35
25
50
35
70
42
85
ZOOM (mm)
16
Control panel display
Warning details
Remedy
Ref. Page
P. 2 4
8.5
7.5
6.7
6.0
5.3
4.7
4.2
3.8
3.4
3.0
2.7
2.4
2.1
1.9
1.7
1.5
1.3
1.2
1.1
9.9
8.8
7.8
7.0
6.2
5.5
4.9
4.4
3.9
3.5
3.1
2.8
2.5
2.2
2.0
1.8
1.6
1.4
1.2
14.1
12.5
11.2
10.0
8.8
7.9
7.1
6.3
5.6
5.0
4.5
4.0
3.5
3.2
2.8
2.5
2.2
2.0
1.8
15.6
13.8
12.3
11.0
9.7
8.7
7.8
6.9
6.1
5.5
4.9
4.3
3.9
3.5
3.1
2.8
2.5
2.2
1.9
17.0
15.0
13.4
12.0
10.6
9.5
8.5
7.5
6.7
6.0
5.4
4.7
4.2
3.8
3.4
3.0
2.7
2.4
2.1
19.8
17.5
15.7
14.0
12.4
11.1
9.9
8.8
7.8
7.0
6.3
5.5
4.9
4.4
3.9
3.5
3.1
2.8
2.5
22.6
20.0
17.9
16.0
14.1
12.6
11.3
10.0
8.9
8.0
7.2
6.3
5.7
5.1
4.5
4.0
3.6
3.2
2.8
25.5
22.5
20.1
18.0
15.9
14.2
12.7
11.3
10.1
9.0
8.0
7.1
6.4
5.7
5.0
4.5
4.0
3.6
1/160
1/200
1/250
1/320
1/400
1/500
1/640
1/800
1/1000
1/1250
1/1600
1/2000
1/2500
1/3200
1/4000
1/5000
1/6400
1/8000
Out of light control
range in AUTO
mode
Change the camera’s ISO speed or lens
iris (F) setting.
Subject too close in
MANUAL mode
①Change the camera’s ISO speed or
lens iris (F) setting.
②Change the guide number (GN) set-
ting.
P. 2 7
P. 3 2
P. 4 3
Shutter speed
Subject too close in
FP MANUAL mode
①Change the camera’s ISO speed or
lens iris (F) setting.
②Change the guide number (GN) set-
ting.
3.2
The guide numbers (GN) for light intensity ratios other than 1/1 in the FP MANUAL mode can
be calculated with the following formula.
Guide number (GN) = Guide number at 1/1 x Light intensity ratio coefficient
Light intensity ratios and their coefficients
Wide panel
request in all
modes
Set the wide panel.
Light intensity ratio
Coefficient
1/1
1.0
1/2
1/4
0.5
1/8
1/16
0.25
0.71
0.35
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
• Digital camera without communication capability
Control panel display
Warning details
Control panel display
Warning details
Remedy
Remedy
Ref. Page
P. 4 1
Ref. Page
P. 4 1
Downward
bounce in all
modes
The light-emitting section is set at 7°
downward.
Cancel this setting except for close-up
flash photography.
Downward
bounce in all
modes
The light-emitting section is set at 7°
downward.
Cancel this setting except for close-up
flash photography.
Wide panel warn-
ing in all modes
The wide panel is set.
Wide panel warn-
ing in all modes
The wide panel is set.
Pay attention to the distance to the sub-
ject since a lower guide number (GN) is
selected.
Pay attention to the distance to the sub-
ject since a lower guide number (GN) is
selected.
P. 4 3
P. 4 3
P. 3 5
Change the camera’s ISO speed or lens
iris (F) setting.
Out of light control
range in AUTO
mode
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Q Why doesn’t the control mode change when I press the MODE button?
A When the electronic flash is connected to certain types of communication-capable camera, the
flash control mode can only be controlled from the camera.
Q&A
Q Is multi-flash shooting possible in the TTL AUTO mode?
A No, it is not possible.
Q The picture is overexposed. What should I do?
Q When are test flash activation and auto checking effective?
A Checking the optimum flash activation based on the AUTO CHECK lamp is particularly effective in
bounce flash (in AUTO modes only).
A First check the shooting range displayed on the control panel. If your subject is closer than the
displayed shooting range, try one of the following so that the shooting range becomes valid to
your subject.
• Stop down the lens aperture.
• Set the light intensity adjustment value to the negative side (
• Use the wide panel.
Q What will happen if the electronic flash is activated simultaneously with the camera’s built-in flash?
A In the TTL mode, both flashes emit light simultaneously and the optimum exposure is determined
according to the combined total light intensity (provided that the camera is in the P or A shooting
mode). In bounce flash photography, the camera’s built-in flash can also be used for catch-light
photography (see page 46).
-).
Q What is the recommended white balance setting for the camera when using the flash?
A The auto white balance mode is recommended. If you use the manual white balance mode, set the
color temperature to 5500K. Note that the color temperature varies depending on the flash shoot-
ing conditions.
Q Why does the electronic flash get hot after successive firing?
A The batteries generate heat when flash firing is repeated successively. In this case, use the elec-
tronic flash at intervals until the flash emission section and batteries cool down.
Q The light control range is not displayed on the control panel. What is wrong?
A The light control range is not displayed in the following cases:
• When the Extension Tube EX-25 (optional) is used
• When the lens is removed
Q Why can’t I mount the electronic flash on the camera?
A The electronic flash cannot be mounted if the lock pin is in the out position. If this is the case, turn
the lock ring all the way in the opposite direction to [←LOCK] until it stops. Once the lock pin is in
the in position, you can mount the electronic flash on the camera (see page 18).
• During bounce photography
• During light intensity adjustment
• When the ISO speed and lens iris (F) are out of the setting range
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Q When the Olympus E-1 digital camera enters the sleep mode, the FL-36 control panel displays
turn off. Is this normal?
MAIN SPECIFICATIONS
A Yes, it is normal. When the E-1 enters the sleep mode, the FL-36 does as well. When the camera
wakes up, so does the FL-36.
Model Number
Type
Guide number
: FS-FL36
: External electronic flash for digital still camera
: Automatic switching
36: When in 42 mm (85 mm with 135 type)
20: When in 12 mm (24 mm with 135 type)
8/10 switching: When the wide panel is used.
: Automatic switching.
Q Does the FL-36 also turn off when the Olympus E-1 digital camera is turned off?
A When the E-1 is turned off, the FL-36 enters the sleep mode.When the E-1 is turned on again, the
FL-36 also turns on. When you want to turn off the FL-36, turn off the FL-36 before turning off the
E-1. In addition, when connected to a camera without communication capability, the FL-36
enters the sleep mode if it is not operated for about 15 minutes.
Firing angle
At 12 mm: Up-down 61
°
, left-right 78°(equivalent to image angle of 12 mm lens)*
At 42 mm: Up-down 21
°
, left-right 28°(equivalent to image angle of 42 mm lens)*
When the wide panel is used for 8 mm: Up-down 83°, left-right 101°
(equivalent to image angle of 8 mm lens)*
* ZOOM values are the FOUR THIRDS camera values.
: Approx. 1/20000 to 1/500 sec. (Variable according to the light intensity, except in FP
emission.)
Flash emission period
Flash emission count
(at full activation)
:
Approx. 150 times (using the LR6-type AA (R6) alkaline dry cell batteries)
Approx. 320 times (using the LB-01 type lithium battery packs)
(Variable depending on shooting conditions)
Recharge time
:
Approx. 7.5 seconds (using the AA (R6) alkaline manganese batteries)
Approx. 6.5 seconds (using the LB-01 type lithium battery packs)
(from full activation to
charge lamp lighting)
Flash modes
Bounce angles
Auto power OFF
: TTL AUTO, AUTO, MANUAL, FP TTL AUTO, FP MANUAL
: Up 0 to 90°, down 7°, right 0 to 90°, left 0 to 180°
: Interlocks with the auto power OFF operation of a camera with communication capa-
bility
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
AF illuminator
Power supply
: Automatic firing at low intensity, possible only when a camera with communication
capability is connected.
Standard effective distances (Variable depending on the camera and lens in use.)
1 to 5 m (3.3 to 16.4 ft)
:
:
AA (R6) alkaline dry cell batteries (LR6) x 2, AA (R6) Ni-Cd batteries x 2, AA (R6) Ni-Mh
batteries x 2, AA (R6) Ni-Mn batteries (ZR6) x 2, AA (R6) oxyride batteries (ZR6Y type) x 2,
AA (R6) lithium batteries (FR6) x 2 or 3 V lithium battery pack (Olympus LB-01) x 1
67(W) x 108(H) x 95(D) mm (2.6 x 4.3 x 3.7 in) (excluding protrusions)
Dimensions
Weight
: 210 g (7.4 oz) (excluding batteries)
Operating environment
: Temperature: 0 to 40°C (32 to 104°F)
Humidity: No more than 80% (without condensation)
Specifications are subject to change without any notice or obligation on the part of the manufacturer.
● Technical Support (USA)
Phone customer : Tel.1-800-260-1625 (Toll-free)
Our phone customer support is available from 8 am to
10 pm (Monday to Friday) ET
E-Mail : [email protected]
● European technical Customer Support
or call NUMBER : Tel.00800-67 10 83 00 (Toll-free)
+49 1805-67 10 83 or +49 40-23 77 38 99 (Charged)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
|