Download from Www.Somanuals.com. All Manuals Search And Download.
PUBLICATION ISSUED BY:
Olivetti S.p.A.
Gruppo Telecom Italia
Via Jervis, 77 - 10015 Ivrea (ITALY)
Copyright © 2006, Olivetti
All rights reserved
The
mark affixed to the product certifies that
the product satisfies the basic quality
requirements.
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time
and without any notice.
ENERGY STAR is a U.S. registered mark.
The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection
Agency in response to environmental issues and for the purpose of advancing the development and utilization of
more energy efficient office equipment.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well
as the characteristics of the product:
• incorrect electrical power supply;
• incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the
User’s Manual supplied with the product;
• replacement of original components or accessories with others of a type not approved by the manufacturer, or
performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photocopying, recording or
by any information storage and retrieval system, without permission in writing from
the Publisher.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
Caution label on the unit
The label (
) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using the unit
Follow the cautions below when using this unit.
Warning:
• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.
• Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15
seconds before turning it back on.
• Unit power must be turned off before installing any supplies.
Caution:
• Place the unit on a firm, level surface.
• Do not install the unit in a humid or dusty location.
• When the unit is not used for a long time, for example for consecutive holidays,
turn the power switch off and remove the power cord from the outlet.
• When moving the unit, be sure to turn the power switch off and remove the power
cord from the outlet.
• Do not cover the unit with a dust cover, cloth or plastic film while the power is on.
Doing so may prevent heat radiation, damaging the unit.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the
machine for servicing and proper ventilation.
A small amount of ozone is produced within the unit during
operation. The emission level is insufficient to cause any health hazard.
Note:
3
The present recommended long term exposure limit for ozone is 0.1ppm (0.2mg/m ) calculated
as an 8hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable
to place the unit in a ventilated area.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions on handling
Be careful in handling the unit as follows to maintain the performance of this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Do not expose the drum cartridge to direct sunlight.
• Doing so will damage the surface (green portion) of the drum cartridge, causing
smudges on copies.
Store spare supplies such as drum cartridges and TD cartridges in a dark
place without removing from the package before use.
• If they are exposed to direct sunlight, smudges on copies may result.
Do not touch the surface (green portion) of the drum cartridge.
• Doing so will damage the surface of the cartridge, causing smudges on copies.
Cautions on laser
Wave length
Pulse times
Output power
770 nm - 795 nm
11.82 µs/7 mm
0.17 mW + 0.01 mW
-
Trademark acknowledgements
• Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A. and
other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
As an ENERGY STAR® Partner, OLIVETTI has determined that
this product meets the ENERGY STAR® guidelines for energy
efficiency.
Safety precautions:
This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the
CDRH standards. This means that the unit does not produce hazardous laser radiation. For
your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The unit’s exterior covers contain several safety interlock switches. Do not bypass any
safety interlock by inserting wedges or other items into switch slots.
In some areas, the "POWER" switch positions are marked "I" and "O" on the copier
instead of "ON" and "OFF".
The symbol "O" denotes the copier is not completely de-energized but in a stand-by
condition at this "POWER" switch position.
If your copier is so marked, please read "I" for "ON" and "O" for "OFF".
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1 INTRODUCTION
5 MAKING COPIES
USING THE MANUALS.................4
PART NAMES................................5
OPERATION PANEL .....................6
COPY FLOW ...............................46
ORIGINAL PLACEMENT.............47
SET THE COPY QUANTITY .......49
EXPOSURE ADJUSTMENT/
PHOTO COPYING.......................50
REDUCTION/ENLARGEMENT/
ZOOM ..........................................52
1
2
3
4
5
6
7
8
9
2 SETTING UP THE UNIT
SETUP PROCEDURE...................7
CHECKING PACKED
COMPONENTS AND
6 SPECIAL FUNCTIONS
ACCESSORIES.............................8
PREPARING THE UNIT FOR
INSTALLATION..............................8
SCAN HEAD LOCKING SWITCH .9
INSTALLING THE
TD CARTRIDGE.......................... 10
CONNECTING THE POWER
CORD .......................................... 12
POWER ON................................. 12
TWO SIDED COPYING ...............53
DESCRIPTION OF SPECIAL
FUNCTIONS................................55
TONER SAVE MODE ..................55
USER PROGRAMS.....................56
DISPLAYING TOTAL NUMBER
OF COPIES .................................57
7 MAINTENANCE
3 LOADING PAPER
TD CARTRIDGE
REPLACEMENT..........................58
DRUM CARTRIDGE
REPLACEMENT..........................59
CLEANING THE UNIT.................60
PAPER......................................... 14
LOADING THE PAPER TRAY ..... 15
BYPASS FEED
(including special paper).............. 17
4
INSTALLING THE SOFTWARE
SOFTWARE FOR THE
OLIVETTI PERSONAL MFP
8
TROUBLESHOOTING THE UNIT
TROUBLESHOOTING.................62
STATUS INDICATORS.................63
MISFEED REMOVAL...................64
SERIES........................................ 19
HARDWARE AND SOFTWARE
REQUIREMENTS........................19
BEFORE INSTALLATION............ 20
INSTALLING THE SOFTWARE... 21
INDICATORS ON THE
OPERATION PANEL ................... 31
USING THE PRINTER MODE..... 32
USING THE SCANNER MODE........ 34
HOW TO USE THE
ONLINE MANUAL ....................... 43
USING OTHER INSTALLED
DRIVERS..................................... 44
CONNECTING THE INTERFACE
CABLE......................................... 45
9 APPENDIX
SPECIFICATIONS .......................69
ABOUT SUPPLIES AND
INTERFACE CABLES..................71
MOVING AND STORING
THE UNIT ....................................72
INDEX..........................................73
SOFTWARE LICENSE ................76
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
1
This chapter provides basic information for using the unit.
USING THE MANUALS
In addition to this printed manual an online manual is also provided. To get full use of all
features and functions of this product, be sure to familiarize yourself with both manuals.
This printed manual provides all installation and setup instructions as well as instructions
in the use of all copier functions. The online manual contains the following information.
Online manual
Provides you with information on how to specify preferences and troubleshooting. Check
the online manual when you use this unit after all the initial setup is completed.
How to use the online manual
Explains how to use the online manual.
Print
Provides information on how to print a document.
Scan
Explains how to scan using the scanner driver and how to adjust the settings for
the Button Manager.
Troubleshooting
Provides instructions on how to solve driver or software problems.
Conventions used in this manual and online manual
• This operation manual explains the operation of models with and without the SPF. In
cases where the operation is the same, the SPF model is used.
• Illustrations of driver screens and other computer screens show the screens that
appear in Windows XP Home Edition. Some of the names that appear in these
illustrations may differ slightly from the screens that appear in other operating systems.
• This operation manual refers to the Single Pass Feeder as the "SPF".
• In this manual, the following icons are used to provide the user with information
pertinent to the use of the unit.
Warns the user that injury may result if the contents of the warning
are not properly followed.
Cautions the user that damage to the unit or one of its components
may result if the contents of the caution are not properly followed.
Notes provide information relevant to the unit regarding
specifications, functions, performance, operation and such, that
may be useful to the user.
Indicates a letter displayed in the display.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAMES
1
Power switch
10
11
12
13
Original table
1
2
3
4
5
Handle
Operation panel
Front cover
Power cord socket
Fusing unit release lever
Transfer charger
Charger cleaner
Paper tray
14
15
Side cover
Side cover open button
Bypass paper guides
Paper output tray
Paper output tray extension
6
7
8
9
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION PANEL
11
ON LINE key and indicator
Lights up when the unit is used as a
printer and scanner. For description of
the ON LINE indicator, see
"INDICATORS ON THE OPERATION
PANEL" (p.31).
Power save indicator
Lights up when the unit is in a power
save mode. (p.55, p.56)
Paper feed location indicators
Light up to show the selected paper
feed station.
Zoom keys and indicator
Use to select any reduction or
enlargement copy ratio from 25% to
400% in 1% increments. (p.52)
Copy quantity keys
• Use to select the desired copy
quantity (1 to 99). (p.49)
• Use to make user program entries.
(p.56)
Original to copy key and indicators
Two-sided copies from
1
one-sided originals.
Turn on Long Edge or
Turn on Short Edge
can be selected.
12
13
14
Exposure mode selector key and
indicators
Use to sequentially select the exposure
modes: AUTO, MANUAL or PHOTO.
Selected mode is shown by a lit
indicator. (p.50)
Light and dark keys and exposure
indicators
Use to adjust the MANUAL or PHOTO
exposure level. Selected exposure level is
shown by a lit indicator. (p.50) Use to start
and terminate user program setting. (p.56)
Alarm indicators
2
3
4
15
16
Drum replacement required
indicator (p.59)
Clear key
Misfeed indicator (p.64)
• Press to clear the display, or press
during a copy run to terminate
copying. (p.49)
• Press and hold down during standby
to display the total number of copies
made to date. (p.57)
TD cartridge replacement
required indicator (p.58)
SPF indicator (p.48)
(15 cpm model only)
SPF misfeed indicator (p.67)
(15 cpm model only)
Copy ratio selector key and
indicators
Use to sequentially select preset
reduction/enlargement copy ratios.
Selected copy ratio is shown by a lit
indicator. (p.52)
5
6
7
Start key and indicator
17
• Copying is possible when the
indicator is on.
• Press to start copying
• Use to set a user program. (p.56)
Copy ratio display (%) key (p.52)
Display
8
9
Displays the specified copy quantity,
zoom copy ratio, user program code,
and error code.
SCANNER key and indicator
(p.31, p.39)
10
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP THE UNIT
2
Follow the installation procedure below to use the unit properly.
If the unit does not function properly during setup or use, or if a function
cannot be used, see "TROUBLESHOOTING THE UNIT" (p.62).
2
SETUP PROCEDURE
When using the unit for the first time, setup the unit following the procedure shown
below.
1 Open the package, and make sure that all the accessories are
supplied with the unit. (p.8)
2 Remove the protective materials. (p.9)
3 Install the TD cartridge. (p.10)
4 Load the paper in the paper tray (p.15)
5 Insert the attached power cord into the power cord socket at the
rear of the unit.
6 Plug the other end of the power cord into the nearest outlet. (p.12)
7 Install the software.*1 (p.19)
8 Connect the interface cable*1 (p.45) and turn on the unit. (p.12)
9 Now, you can copy (p.46), print (p.32), or scan (p.34) your
document.
1
*
If you are only using the unit for copying, skip this step.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING PACKED COMPONENTS AND
ACCESSORIES
Open the carton and check if the following components and accessories are
included.
If anything is not included or is damaged, contact your authorized Service
representative.
Power cord
PREPARING THE UNIT FOR INSTALLATION
Be sure to hold the handles on
1
both sides of the unit to unpack
the unit and carry it to the
installation location.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove all pieces of tape shown in the illustration below. Then
open the original cover/SPF and remove protective materials.
After that, take out the bag containing the power cord and TD
cartridge.
2
2
12 cpm model
15 cpm model
12 cpm model
15 cpm model
SCAN HEAD LOCKING SWITCH
The scan head locking switch is under the original table. If the switch is locked (
the unit will not operate. Unlock the switch ( ) as shown below.
),
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE TD CARTRIDGE
Open the side cover.
1
Push gently on both sides of the
front cover to open the cover.
2
Remove the TD cartridge from the bag. Hold the cartridge on
3
both sides and shake it horizontally four or five times. Hold the
tab of the protective cover and pull the tab to your side to
remove the cover.
4 or 5 times
Gently insert the TD cartridge
until it locks in place while
4
pushing the lock release button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the front cover and then
the side cover by pressing the
round projections near the
side cover open button.
5
When closing the covers, be
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE POWER CORD
If you use the unit in a country other than the country where the unit was
purchased, you will need to make sure that your local power supply is
compatible with your model. If you plug the unit into an incompatible
power supply, irreparable damage to the unit will result.
Ensure that the power switch of
1
the unit is in the OFF position.
Insert the attached power cord
into the power cord socket at the
rear of the unit.
Plug the other end of the power cord into the nearest outlet.
2
Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.
Power on
Ensure that the power switch of the unit is in the OFF position. Plug the other end of
the power cord into the nearest outlet. Turn the power switch on the left side of the
unit to the "ON" position. The start ( ) indicator will light up and other indicators
which show the initial settings of the operation panel will also light up to indicate the
ready condition. For the initial settings, see the "Initial settings of operation panel"
described on the next page.
• The unit will enter a power save mode once the set time has elapsed
without any unit operation . The settings of the power save modes can
be modified. See "USER PROGRAMS" (p.56).
• The unit will return to the initial settings a preset amount of time after
the end of copy, or scanner job. The preset amount of time (auto clear
time) can be changed. See "USER PROGRAMS" (p.56).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition
(when the Start indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality. At this
time, the scan head moves automatically. This is normal and does not indicate unit
trouble.
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when
the time set with the "Auto clear time" setting (p.55) elapses after a copy or scanner
job is finished, or when the clear (
The initial settings of the operation panel are shown below.
) key is pressed twice.
2
"0" is displayed in the display
When copying is begun in this state, the settings in the following table are used.
Copy quantity
Exposure adjustment
Zoom
1 copy
Auto
100%
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power
shut-off mode (p.55) in order to minimize power consumption. In cases where the
machine will not be used for a long time, turn off the power switch and remove the
power cord from the outlet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING PAPER
3
Follow the steps below to load paper into the tray.
PAPER
For best results, use only paper recommended by OLIVETTI.
Type of paper
feeding
Type of media
Size
Weight
2
Paper tray
Standard paper
A4
56 to 80g/m
B5
A5
Letter
Legal
Invoice
2
Single bypass Standard paper and
thick paper
A4
B5
52 to 128g/m **
A5
B6
A6
Letter
Legal
Invoice
Special Transparency A4
media film
Letter
Envelope*
International DL
International C5
Commercial 10
Monarch
* Do not use non-standard envelopes, and envelopes that have metal clasps, plastic
snappers, string closures, windows, linings, self-adhesive, patches or synthetic
materials. Do not use envelopes that are filled with air or envelopes that have
labels or stamps attached. These will cause physical damage to the unit.
2
** For paper weighing from 104 to 128g/m , A4 is the maximum size that can be fed
through the single bypass.
• Special papers such as transparency film, labels and envelope must be fed one
sheet at a time through the single bypass.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING THE PAPER TRAY
Raise the handle of the paper tray
and pull the paper tray out until it
1
stops.
Remove the pressure plate lock. Rotate the pressure plate lock
in the direction of the arrow to remove it while pressing down
the pressure plate of the paper tray.
2
3
Store the pressure plate lock which has been removed in step 2.
To store the pressure plate lock, rotate the lock to fix it on the
3
relevant location.
Pressure plate lock
Adjust the paper guides on the paper tray to the copy paper
width and length. Squeeze the lever of paper guide A and slide
the guide to match with the width of the paper. Move paper
4
guide
to the appropriate slot as marked on the tray.
B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan the paper and insert it into the tray. Make sure the edges go
under the corner hooks.
5
Do not load paper above the maximum height line (
the line will cause a paper misfeed.
). Exceeding
Gently push the paper tray back into the unit.
6
• After loading paper, to cancel the blinking
copying, press the clear ( ) key. The
and the start ( ) indicator will light up.
Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges.
without restarting
in the display will go out
•
• Make sure all the paper in the stack is the same size and type.
• When loading paper, ensure there is no space between the paper and
the guide, and check if the guide is not set too narrow causing the
paper to bend. Loading paper in these ways will result in document
skew or a paper jam.
• When not using the unit for an extended period, remove all paper from
the paper tray and store it in a dry place. If paper is left in the unit for
an extended period, the paper will absorb moisture from the air,
resulting in paper jams.
•
When adding new paper to the paper tray, remove the old paper already
contained in the tray. Placing new paper on top of the paper already
contained in the tray may result in feeding two sheets at one time.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BYPASS FEED (including special paper)
The single bypass can be used to feed standard paper, transparency film, labels, envelopes,
and other special purpose paper. Paper measuring from A6 to A4/Legal and in the weight range
2
2
of 52 to 128g/m can be used in this tray. (For paper weighing from 104 to 128g/m , A4 is the
maximum size.)
•
The single bypass can hold one sheet of paper.
• The original image must be smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this may cause
smudges on the edges of the copies.
The single bypass
• If you insert a sheet of paper into the single bypass when multiple
copies have been set with the copy quantity setting (p.49), the copy
quantity setting will change to "0" and only one copy will be made.
• When copying onto transparency film, remove each copy promptly. Do
not let copies stack up.
3
Select copy and print settings before you begin the copy job.
1
2
For information on the copy settings, see "MAKING COPIES" (p.46). For
information on the print settings, see the online manual or the Help file for
the printer driver, and then begin printing from the single bypass.
Set the paper guides to the paper width. Insert a single sheet of
copy or print paper (print face down) into the feed slot of the
single bypass.
Using copy mode
When you insert the paper, the machine will automatically draw in the paper
and begin copying.
Using printer mode
After
appears in the display, wait until the Paper feed location indicator
for the single bypass illuminates and insert the paper. The machine will
automatically draw in the paper and begin printing.
Print face
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Note for loading envelopes
• Envelopes must be fed narrow side into the feed slot one sheet at a time.
• Do not use non-standard envelopes, and envelopes that have metal clasps,
plastic snappers, string closures, windows, linings, self-adhesive, patches or
synthetic materials. Do not use envelopes that are filled with air or envelopes that
have labels or stamps attached.
• Envelopes of which the surface is not flat because of embossing may cause the
prints to become smudged.
• Under high humidity and temperature conditions the glue flaps on some
envelopes may become sticky and be sealed closed when printed.
• Use only envelopes which are flat and crisply folded. Curled or poorly formed
envelopes may be poorly printed or may cause misfeeds.
• Be sure to select either Com10, DL, C5 or Monarch on the paper size setting of
the printer driver. (For detailed information on printer driver, refer to the online
manual.)
• It is recommended that you perform a test print before performing the actual print
job.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE
4
This chapter provides you with information on how to install required software to use
this unit with your computer. Information on how to use the online manual is also
provided. The following term is used in this chapter.
CD-ROM
Means the supplied CD-ROM with the OLIVETTI Personal MFP Series software.
SOFTWARE FOR THE OLIVETTI PERSONAL MFP
SERIES
The supplied CD-ROM includes software for this unit.
MFP driver
Scanner driver
Permits you to operate scanning function of this unit with TWAIN-compliant and
WIA-compliant application.
Printer driver
Enables you to use the printer function of this unit with your computer.
Print Status Window
4
The print state and information on current printing are displayed on the status
monitor window.
Desktop Document Manager
An integrated software environment that makes it easy to manage document and
image files and launch applications.
Button Manager
Button Manager enabling the SCANNER (
) key located on the unit.
The scanning feature is only available with Windows 98/Me/2000/XP
using a USB connection. For users running Windows 95/NT 4.0 or using
a parallel connection, only printing is available.
HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements in order to install the software.
Computer type
IBM PC/AT or compatible computer equipped with a
USB1.1* or bi-directional parallel interface (IEEE 1284)
1
Operating system*2 Windows 95, Windows 98, Windows Me, Windows NT
3
Workstation 4.0 (ServicePack 5 or later)* , Windows 2000
3
3
Professional* , Windows XP Professional* , Windows XP
3
Home Edition*
Display
800 x 600dots (SVGA) display with 256 colors (or better)
Hard disk free space 150MB or more
Other requirement An environment on which any of the operating systems listed
for hardware
above can fully operate
1
* Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP
Professional or Windows XP Home Edition preinstalled model with USB interface
equipped as standard.
2
3
* Printing is unavailable in MS-DOS mode.
* The administrator's authorization is required to install this software using this installer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
The following table shows the drivers and software that can be installed for each
version of Windows and interface connection method.
MFP Driver
Desktop
Button
Manager
Printer driver/
Print Status
Window
Document
Manager
Scanner driver
Users of Windows
98/Me/2000/XP who
will use the USB
Available
Available
Available
interface connection
Users of Windows
98/Me/2000/XP who
will use the parallel
interface connection
1
Available*
Not
Available
2
Not Available
Available*
Windows 95/NT 4.0
users
1
* When the unit is connected through the parallel port, the Print Status Window can only
be used when the parallel port is set to ECP mode. To set the parallel port mode, refer
to your computer manual or ask the manufacturer of your computer.
2
* Desktop Document Manager can be installed when using a parallel interface
connection, however, the unit’s scanner function cannot be used.
Is there another GDI printer driver or a Windows Printing System printer
driver already installed? If installed, change the printer port setting. For
the change of the printer port setting, see "USING OTHER INSTALLED
DRIVERS" (p.44).
Flow of installation
Refer to the following table and then begin installation
Operating
system
Interface
Reference pages for how to install
USB/
Parallel (p.21)
Installing onto Windows XP (USB/parallel interface)
Windows XP
USB
Parallel
USB
Installing onto Windows 98/Me/2000 (USB interface) (p.25)
Windows 98
Windows Me
Windows 2000
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.28)
Installing onto Windows 98/Me/2000 (USB interface) (p.25)
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.28)
Parallel
USB
Installing onto Windows 98/Me/2000 (USB interface) (p.25)
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.28)
Parallel
Windows 95/
NT 4.0
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.28)
Parallel
20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE
The following term is used in this section.
MFP
Means the unit as a printer and scanner.
• For this description, it is assumed that the mouse is configured for
right hand operation.
• To print or scan, the MFP must be in the online state.
• The scanner feature only works when using a USB interface cable.
• If any error message appears, solve the problem following the
instructions on the screen. After your problem is solved, the installing
procedure will be continued. Depending on your problem, you may
have to exit the installer. In this case, click the "Cancel" button to exit
the installer. After solving your problem, reinstall the software from the
beginning.
Installing onto Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not
connected to the MFP.
4
Insert the supplied CD-ROM into your CD-ROM drive.
1
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
2
When any of "Found New Hardware Wizard" messages appear during
the software installation, be sure to click the "Cancel" button.
Double-click the "Setup" ( ) icon.
3
If the language selection screen appears after you double click the
"Setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
Select the software packages to be
installed, and then click the "Next"
button.
4
The software packages with checkmark (
on the list on the screen will be installed.
)
Desktop Document Manager
Click the "Display README" button to show
the information on the selected package.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are using the parallel interface connection, do not select the
Button Manager checkbox because this feature is not supported with
the parallel interface.
• If the following screen appears, click the "OK" button. Review the
contents in "BEFORE INSTALLATION" (p.20), and then select only
appropriate the software packages to be installed.
Review the software packages to be
installed on the screen, and then click
the "Start" button.
5
6
The software packages to be installed will be
Desktop Document Manager
displayed on the screen. If inappropriate
packages are displayed, click the "Back" button
to select appropriate packages again.
Copying files for MFP driver installation (This step will start if it
was selected in step 4).
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the USB or parallel
interface cable is not connected to the MFP. Make sure that the
interface cable is not connected and click the "Next" button.
2
Click the "Next" button in the dialog box to
install the MFP driver or Cancel to quit the
installation.
3
The setup program will start to copy the files.
If the following screen appears while the files are
being copied (the message may appear more
than once), click "Continue Anyway".
When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
4
The Button Manager installer will start.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Button Manager (This step will start if it
was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
Read the message in the "Please read the following information."
window, and then click the "Next" button.
2
When a message appears that lets you specify the location for the
software to be installed, click the "Next" button.
3
If the program displays "Do you want the Button Manager added to
Windows Startup?", check "Yes" and click the "OK" button.
4
The setup program will start to copy the files.
Click the "Finish" button when the message informs you that
setup is successful.
5
The Desktop Document Manager installer will start.
Begin installation of the Desktop Document Manager (This step
will start if it was selected in step 4).
8
9
After confirming the message in the "Welcome to Desktop
Document Manager installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
4
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
Click the "Finish" button when the message informs you that
Setup is complete.
5
Click the "Close" button when the
message informs you that "Setup has
finished". When the "Now connect the
MFP interface cable to the PC" dialog
Desktop Document Manager
box appears, click the "OK" button.
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure that the power of the MFP is turned on, and then
connect the USB interface cable or parallel interface cable.
(p.45)
Windows will detect the MFP and the Plug and Play screen will appear. If
you are using Windows XP with the parallel interface, go to step 12.
10
11
Begin installation of the scanner driver.
"Olivetti d-Copia 150D" will appear in the "Found New Hardware
Wizard" dialog box. Select "Install the software automatically
(Recommended)" and click the "Next" button.
1
The "Install hardware" dialog box will appear. Click the "Continue
Anyway" button.
2
When installation of the driver is completed, click the "Finish"
button to finish the scanner driver installation.
3
Begin installation of the printer driver.
12
"Olivetti d-Copia 150D" will appear in the "Found New Hardware
1
Wizard" dialog box. Select "Install the software automatically
(Recommended)" and click the "Next" button.
The "Hardware Installation" dialog box will appear. Click the
"Continue Anyway" button.
2
When installation of the driver is completed, click the "Finish"
button to finish the printer driver installation.
3
You have completed the installation of all the software.
The "d-Copia 150D" driver is common to all models of the Olivetti
Personal MFP Series.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing onto Windows 98/Me/2000 (USB interface)
Before starting the installation, make sure the USB interface cable is not connected
to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Double-click "My Computer" ( ), and then double-click the
CD-ROM ( ) icon.
2
When any of "Hardware Found", or "Found New Hardware Wizard"
messages appear during the software installation, be sure to click the
"Cancel" button.
Double-click the "Setup" ( ) icon.
3
If the language selection screen appears after you double click the
"Setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
4
Select the software packages to be
installed, and then click the "Next"
button.
4
The software packages with checkmark (
)
on the list on the screen will be installed. Click
the "Display README" button to show the
information on the selected package.
Desktop Document Manager
If the following screen appears, click the "OK" button. Review the
contents in "BEFORE INSTALLATION" (p.20), and then select the
appropriate driver software packages to be installed.
Review the software packages to be installed on the screen,
and then click the "Start" button.
5
The software packages to be installed will be displayed on the screen. If
inappropriate packages are displayed, click the "Back" button to select
appropriate packages again.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying files for MFP driver installation.
6
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the interface cable
is not connected to the MFP. Make sure that the interface cable is
not connected and click the "Next" button.
2
Click the "Next" button in the dialog box
showing the files to be copied for installation
of the MFP driver.
3
The setup program will start to copy the files.
In Windows 2000, if the following screen appears
while the files are being copied (the message
may appear more than once), click "Yes" in
Windows 2000.
Desktop Imaging Setup
The following screen appears when all of the
4
files for the USB interface connection have
been copied. If you are not using a parallel
interface cable for connection to the MFP,
please click the "No" button.
When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
5
The Button Manager installer will start.
Begin installation of the Button Manager (This step will start if it
was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
Read the message in the "Please read the following information."
window, and then click the "Next" button.
2
When a message appears that lets you specify the location for the
software to be installed, click the "Next" button.
3
If the program displays "Do you want the Button Manager added to
Windows Startup?", check "Yes" and click the "OK" button.
4
The setup program will start to copy the files.
Click the "Finish" button when the message to inform you of the
completion of the installation appears.
5
The Desktop Document Manager installer will start.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Desktop Document Manager (This step
will start if it was selected in step 4).
8
After confirming the message in the "Welcome to Desktop
Document Manager installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
The setup program will start to copy the files.
Desktop Imaging Setup
If the dialog box asking "This program is about
to install Desktop Imaging, which does not
Desktop Imaging,
support LZW compression." appears, answer
the question to continue the Desktop
Document Manager installation.
Click the "Finish" button when the message
to inform you of the completion of the installation appears.
5
4
Click the "Close" button when the
message to inform you of the
completion of the installation appears.
9
When the "Now connect the MFP
Desktop Document Manager
interface cable to the PC." dialog box
or "After Windows system restarts..."
dialog box appears, click the "OK"
button.
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
Make sure that the power of the MFP is turned on, and then
connect the USB interface cable. (p.45)
10
11
Windows will detect the MFP and the Plug and Play screen will appear.
Follow the instructions in the Plug and Play screen that
appears in your version of Windows to begin the installation.
You have completed the installation of the software.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not
connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Double-click "My Computer" ( ), and then double-click the
CD-ROM ( ) icon.
2
When any of "Hardware Found", or "Found New Hardware Wizard"
messages appear during the software installation, be sure to click the
"Cancel" button.
Double-click the "Setup" ( ) icon.
3
If the language selection screen appears after you double click the
"Setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
Select the software packages to be
installed, and then click the "Next"
button.
4
The software packages with checkmark (
on the list on the screen will be installed.
)
Desktop Document Manager
Click the "Display README" button to show
the information on the selected package.
In Windows 95/NT 4.0, "Button
Manager" does not appear. In
Windows 98/Me/2000, do not select
the "Button Manager" checkbox.
because this is not supported when
using the parallel interface.
The next screen appears. Make sure that the parallel interface
cable is not connected, and click "OK".
5
6
Windows 95/NT 4.0
Windows 98/Me/2000
Check the contents of the package on the screen, and then
click the "Start" button.
The software packages to be installed will be displayed on the screen. If
inappropriate packages are displayed, click the "Back" button to select only
appropriate software packages.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying files for MFP driver installation and parallel interface
setup (This step will start if it was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the USB or parallel
interface cable is not connected to the MFP. Make sure that the
interface cable is not connected and click the "Next" button.
2
Click the "Next" button in the dialog box to
install the MFP driver or Cancel to quit the
installation.
3
The setup program will start to copy the files.
In Windows 2000, if the following screen appears
while the files are being copied (the message
may appear more than once), click "Yes" in
Windows 2000.
The following screen appears. Click the "Yes" button, and then the
Model screen will appear. Select the model number that is the
same as the model name of your MFP and click the "Next" button.
4
Be sure to select the displayed model number that is the same as the
MFP’s model name. If they are not the same, the driver will not be
installed correctly.
OLIVETTI MFP Driver
OLIVETTI MFP Driver
4
d-Copia 150D
OLIVETTI MFP Driver
Establish the printer settings and click the
"Next" button.
5
Select "LPT1" for the port to be used. If "LPT1"
does not appear, it is likely that another printer or
peripheral device is using "LPT1". Check your
other printers and peripheral devices, and change
the port setting as needed so no device is using
"LPT1". If you wish the MFP to be your default
printer, select "Yes". If not, select "No".
When the "Setup has completed gathering all necessary installation
information" dialog box appears, click the "Yes" button.
The parallel interface driver is installed.
When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
6
7
The Desktop Document Manager installer will start.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Desktop Document Manager (This step
will start if it was selected in step 4).
8
After confirming the message in the "Welcome to Desktop
Document Manager installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
The setup program will start to copy the files.
Desktop Imaging Setup
If the dialog box asking "This program is about
to install Desktop Imaging, which does not
Desktop Imaging,
support LZW compression." appears, answer
the question to continue the Desktop
Document Manager installation.
Click the "Finish" button when the message
to inform you of the completion of the installation appears.
5
Click the "Close" button when the
message to inform you of the
9
completion of the installation appears.
When the "Now connect the MFP
Desktop Document Manager
10
interface cable to the PC." dialog box
or "After Windows system restarts..."
dialog box appears, click the "OK"
button.
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
Make sure that the power of the MFP is turned on, and then
connect the parallel interface cable (p.45).
10
You have completed the installation of all the software.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICATORS ON THE OPERATION PANEL
The ON LINE indicator and the Start (
or scanner.
) indicator indicate the state of the printer
Start indicator
On:
Indicates the unit is
ready for copying or
scanning is being
performed.
Blinking: The indicator blinks in
the following situation:
• When a print jobs is
interrupted.
• When reseving a
copy job.
• When toner is being
replenished during a
copy or print job.
Off:
The indicator is off in the following situations:
• During copying or scanning.
• The unit is in the auto power shut-off mode.
• When a misfeed or error has occurred.
ON LINE indicator
The ON LINE key is pressed and on line and off line are changed.
4
On:
Indicates the unit is ready for printing or scanning is being performed.
(On line)
Blinking: Printing or data is being received from a computer.
Off: Copying is being performed. (Off line)
Power save indicator
On:
Indicates the unit is in a power save mode.
Blinking: Indicates that the unit is initialising (when the side cover is opened and
closed or the power turned off and on).
SCANNER indicator
On:
The SCANNER (
) key has been pressed and the unit is in scanner
mode.
Blinking: A scan job is being executed from the computer, or scan data is stored
in the unit's memory.
Off:
The unit is in the copy mode.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PRINTER MODE
For problems with the printer function, see the On Line Manual or the
Help file for the driver.
Opening the printer driver from the start menu
Open the printer driver setup screen by either of the methods shown below.
Click the "start" button.
1
Click "Control Panel", select "Printers and Other Hardware",
and then click " Printers and Faxes.
2
On Windows 95/98/Me/NT4.0/2000, select "Settings" and click "Printers".
Click the "Olivetti d-Copia 150D" printer driver icon in the
"Printers" window and from the "File" menu, select "Properties.
3
On windows NT 4.0, select "Document Defaults" to open the
printer driver setup screen.
Click the "Printing Preferences" button in the "General" tab.
4
On Windows 95/98/Me, click the "Setup" tab.
The printer driver setup screen will appear.
Refer to the Windows manual or help file for more information
on the "General" tab, "Details" tab, "Color Management" tab and
"Sharing" tab.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
How to print
Make sure that the paper of the desired size and type is loaded
in the tray.
1
The procedure for loading paper is the same as for loading copier papier.
See "LOADING PAPER" (p.14).
Open the document you intend to print, and select "Print" from
the application's "File" menu.
2
3
Make sure that "Olivetti d-Copia 150D" is selected as the
current printer. If you intend to change any print setting, click
the "Preferences" button to open the setting dialog.
On Windows 95/98/Me/NT 4.0, click the "Properties" button.
On Windows 2000, the "Properties" button does not appear. Set your
preferences by switching the tab in the "Print" dialog box.
Specify the print settings including the number of copies,
media type, and print quality, and then click the "Print" button
to start printing.
4
On Windows 95/98/Me/NT 4.0, click the "OK" button to start printing.
For details on print settings, see the online manual or the help file for the
printer driver.
4
• If copying is being performed when printing is started, copying will
continue. After copying is complete, printing will be executed when the
clear (
) key is pressed twice, the ON LINE key is pressed to switch
the unit to the online state or approximately 60 seconds (auto clear
time)* elapse.
* The auto clear time varies with a user program setting. See "USER
PROGRAMS" (p.56).
• Preheat mode and auto power shut-off mode will be canceled when
printing is started.
• If the paper size specified from the software application is larger than
the paper size in the printer, part of the image that is not transferred to
the paper may remain on the surface of the drum. In this case, the
backside of the paper may become dirty. If this occurs, change to the
correct size paper and print two or three pages to clean the image.
• If you start a print job while a scan job or copy job is in progress, the
print data will be stored in the unit's memory. When the scan job or
copy job is completed, printing will begin.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCANNER MODE
The scanner driver for this unit includes an STI (Still image) driver and WIA
(Windows Image Acquisition) driver. You can install software that supports the STI
driver and WIA driver to enable scanning using the operation panel of the unit.
For problems with the scanner function, see the online manual or the
help file for the driver.
Using the Button Manager
Setting up the Button Manager
The Button Manager accessory software supports the STI driver and WIA driver. Setup
that is required in Windows to use the Button Manager is explained in the following.
Windows XP
Click the "start" button, select "Control Panel" and click
1
"Printers and Other Hardware", and then click "Scanners and
Cameras" in the start menu. Right click the "Olivetti d-Copia
150D" icon and click "Properties" in the menu that appears.
In the "Properties" screen, click the
"Events" tab.
2
Olivetti d-Copia 150D Properties
Button Manager (Olivetti Personal
Click the "Select an event" button and
select "ScanMenu SC1" from the pull-down
Olivetti d-Copia 150D Properties
3
menu. Select "Button Manager (OLIVETTI
Personal MFP Series)" in "Start this
Button Manager (Olivetti Personal
program" and click "Apply".
Repeat step 3 to set "ScanMenu SC2" through "ScanMenu
SC6".
4
Click the "Select an Event" button and select "ScanMenuSC2" from the pull-
down menu. Select "Button Manager (Olivetti Personal MFP Series)" in
"Start this program" and click "Apply". Do the same for each ScanMenu
through "ScanMenuSC6". When the settings have been completed, click the
"Close" button to close the screen. When the settings have been completed
in Windows, start the Button Manager. Adjust detailed settings and then
scan an image from the unit.For the procedures for starting Button Manager
and adjusting settings, see "Scan Parameter Settings Dialog Box" (p.36).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 98/Me/2000
To scan directly into an application using the Button Manager on Windows 98,
Windows Me and Windows 2000. Set the Event Manager properties to send only to
Button Manager as shown below.
Click the "Start" button, select "Control Panel" from "Settings",
and open "Scanners and Cameras" in start menu.
1
In Windows Me, it occasionally happens that the "Scanners and
Cameras" icon does not appear immediately after installation of
the MFP driver is completed. If the icon does not appear, click
"View all Control Panel options" in the Control Panel and display
the "Scanner and Cameras" icon.
Select "Olivetti d-Copia 150D" and click the "Properties"
button.
2
In Windows Me,right click "Olivetti d-Copia 150D" and click the "Properties"
in the menu that appears.
Olivetti d-Copia 150D Properties
In the "Properties" screen, click the
"Events" tab.
4
3
Olivetti d-Copia 150D Properties
Button Manager (Olivetti Personal MFP series)
Olivetti d-Copia 150D Properties
Click the "Scanner events" button and
select "ScanMenu SC1" from the pull-down
4
Olivetti d-Copia 150D Properties
menu. Select "Button Manager (Olivetti
Personal MFP Series)" in "Send to this
Button Manager (Olivetti Personal MFP series)
application" and click "Apply".
If other application are shown,
deselect the checkboxes for the other
applications and leave only the Button
Manager checkbox selected.
Repeat step 4 to set "ScanMenu SC2" through "ScanMenu SC6".
5
Click the "Scanner events" and select "ScanMenu SC2" from the pull-down
menu. Select "Button Manager (Olivetti Personal MFP Series)" in "Start this
program" and click "Apply". Do the same for each ScanMenu through
"ScanMenu SC6".
When the settings have been completed, click the "OK" button to close the
screen. When the settings have been completed in Windows, start the
Button Manager. Adjust detailed settings and then scan an image from the
unit. For the procedures for starting Button Manager and adjusting settings,
see "Scan Parameter Settings Dialog Box" (p.36).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Parameter Settings Dialog Box
After you have completed the Button Manager settings in
Windows, configure the scan settings in Button Manager.
To configure the scan settings in Button Manager, right click
the (
) icon in the Taskbar and select "Setting" from the
menu that appears.
For details on configuring the scan settings in Button
Manager, see the online manual or the help file.
This is the corresponding setting in
the Button Manager to automatically
send multiple images from the SPF
in full colour at 75 dpi to Desktop
Document Manager using the
operation panel "SC1" scanner key
selection.
This dialog shows the SC1 event set to go directly to Button Manager.
With the Button Manager set to send the image to Desktop Document
Manager (factory default setting) Desktop Document Manager will open
after acquiring the image automatically.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Flow of the Button Manager setting
The Button Manager can directly handle a d-Copia 150D device event and start your
selected application according to the scan setting made on the d-Copia 150D front
panel (SC1, SC2, SC3, SC4, SC5, SC6).
This will scan directly into your application from the device.
Scanner xxx
(where xxx is
the model name
of your unit)
SCANNER key
pressed.
Event Manager
Windows OS
Button Manager
User selected
application
No Selection
dialog is
displayed.
The user
application
opens.
The settings for the Windows Event Manager for
the Olivetti d-Copia 150D device allow the user to
take advantage of the Olivetti Button Manager to
take control of events from Windows and send
scanned images to any application that can be
selected in Button Manager.
S
Olivetti d-Copia 150D
This can be done with the Windows OS showing
the Event Manager selection dialog or directly into
a selected application if the Button Manager is the
only allowed handler for device events from the
Olivetti d-Copia 150D.
4
This is done by changing the Windows device
settings for the d-Copia 150D in the Scanner and
Camera device settings in the Control Panel.
This is the Control Panel
Properties dialog for "Scanners and
Cameras".
37
Download from Www.Somanuals.com. All Manuals Search And Download.
All About The Windows Event Manager and scanner events in
Windows 98, Windows Me, Windows 2000 and Windows XP.
Windows Platforms provide a mechanism for software to handle external events for
a scanner device like the Olivetti d-Copia 150D series products. This mechanism is
controlled by the device manager on a device basis. Applications that can handle
events from a scanner/camera device register with the Windows Event Manager and
shown as available in the registered applications. The path an event takes to get to
the user's selected application depends upon the event settings for the device.
Scanner xxx
(where xxx is
the model name
of your unit)
SCANNER key
pressed.
Event Manager
Windows OS
Event Manager
selection dialog
User selects an
application.
Displayed on
screen
The user
application
opens.
Olivetti d-Copia 150D
This is the Windows Event Manager
Selection Dialog.
Shown are 2 applications registered
to handle the scanner event from the
d-Copia 150D.
Olivetti Personal MFP Series
Olivetti Personal MFP Series
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SCANNER key to begin scanning
• Scanning is not possible during a copy job.
•
If the SCANNER (
be stored.
) key is pressed during a print job, the scan job will
•
When scanning an original that has been placed in the SPF, only one
original can be placed unless you are using Desktop Document Manager.
Press the SCANNER (
) key.
1
The unit enters scan mode.
Place the original you wish to scan on the original table/SPF.
For the procedure for placing the original, see "ORIGINAL PLACEMENT"
(p.47).
2
3
4
Press the right copy quantity key to
display the number of the application that
you wish to use for scanning.
The application numbers are initially as follows.
Application
number
Application launched
Desktop Document Manager (Full colour)
(if installed)
SC1
Desktop Document Manager (Monochrome)
(if installed)
SC2
E-mail (your standard e-mail program in the
Windows OS you are using)
SC3
SC4
SC5
SC6
Fax (if a fax program is installed)
OCR (if an OCR program is installed)
Microsoft Word (if installed)
To check the settings, see "Scan Parameter Setting Dialog Box" (p.36) and
then open the settings window of the Button Manager.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the start (
Scanning will start and the scanned data will be transfered to the
application.
) key.
4
• If the following screen appears, select
Olivetti d-Copia 150D
Button Manager and click "OK". Button
Manager starts and the application
Olivetti Personal MFP Series
Olivetti Personal MFP Series
associated with Button Manager starts. If
you want only Button Manager to start in
this case, set up Button Manager for use in
Windows as explained in "Setting up the
Button Manager" (p.34).
•
If step 4 is performed with the "Show
TWAIN setting screen when scanning" checkbox selected in the
Scan Parameter Setting Dialog Box (p.36), the TWAIN settings
screen (p.41) will automatically appear. Check the settings, and
then press the start (
) key again or click the "Scan" button in
the TWAIN setting screen to start scanning. The scanned data
will be transferred to the application.
Opening the scanner driver and scanning from your computer
Follow the steps below to open the scanner driver setup screen. As an example, this
instruction is given using Desktop Document Manager as an image capture
application.
•
•
Scanning is not possible during a copy and print job.
The method for starting the scanner driver differs depending on the type
of application. Refer to the manual or the help file of your application.
When using the scanner driver to scan an original that has been placed
in the SPF. If you perform a pre-scan (see the online manual or the help
file for the scanner driver), the original in the SPF will be output to the
exit area after scanning. To scan the original after the pre-scan, place
the original in the SPF once again.
•
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the OLIVETTI TWAIN
Place the original you wish to scan on the original table/SPF.
For the procedure for placing the original, see "ORIGINAL PLACEMENT"
(p.47).
1
2
After starting Desktop Document
Desktop Document Manager
Manager, click the "File" menu and
select "Select Scanner".
Click here
Select "OLIVETTI Personal MFP
Series", and click the "Select"
button.
3
4
Olivetti Personal MFP series 1.0 (32-32)
Click here
O
W
li
v
e
tt
i
d-
C
op
ia150D 1.0 (32-32)
If you use more than one scanning device, select the scanner
you want to use through the application. The method for
accessing the "Select Scanner" option, depends upon the
application. For more information, see the online manual or the
help file of your application.
4
Olivetti d-Copia 150D
Select "Acquire Image"
from the "File" menu, or
click the "Acquire" button
(
) .
Scanning
Set the configuration for scanning (refer to the online manual
and help file), and click the "Scanning" button.
Scan is started.
5
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning with the "Scanner and Camera Wizard" in Windows XP
Windows XP includes as a standard feature an image scanning function. The
procedure for scanning with the "Scanner and Camera Wizard" is explained here.
To cancel scanning, click the "Cancel" button in the screen that is
displayed.
0
Place the original you wish to scan on the original table/SPF.
1For the procedure for placing the original, see "ORIGINAL PLACEMENT"
(p.47).
1
Click the "start" button , select "Control
Panel", and click "Printers and Other
2
Olivetti d-Copia 150D
Hardware", and then click "Scanners
and Cameras" in the start menu. Click
the "Olivetti d-Copia 150D" icon and
click "Get picture" in "Imaging Tasks".
The "Scanner and Camera Wizard"
appears. Click "Next" and establish the
basic settings for scanning.
3
For information on the settings, see the
Windows XP help file. After completing each
setting, click "Next".
Select a name, format, and folder for the
scanned image.
4
For information on the image name, file format,
and folder, see the Windows XP help file.
Scanning begins. When scanning ends,
select the next task you wish to perform.
5
For information on each selection, see the
Windows XP help file. To quit the "Scanner and
Camera Wizard", select "Nothing. I’m finished
working with these pictures." and click "Next".
Click "Finish" in the screen that appears.
The "Scanner and Camera Wizard" closes and the scanned image is saved.
6
42
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the unit as the printer or
scanner and a list of methods for dealing with printing or scanner problems.
To access the online manual, your computer must have Acrobat Reader 5.0 or a later version.
If it is not installed, refer to "Installing Acrobat Reader" (below).
Turn on your computer.
1
Insert the supplied CD-ROM into your CD-ROM drive.
2
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
3
On Windows 95/98/Me/NT 4.0/2000, double-click "My Computer" ( ), and
then double-click the CD-ROM ( ) icon.
Double-click the "MANUAL" folder,
the "English" folder, and then the
4
d-Copia 120D / d-Copia 150D
"d-Copia 120D, 150D Online EN.pdf"
icon.
5
4
The following window will appear.
Click the
button to read the online manual.
6
To close the online manual, click the ( ) button located at the top-right of
the window.
• The online manual can be printed out using Acrobat Reader.
OLIVETTI recommends printing out the sections which you refer to
regularly.
• Refer to "Help" of Acrobat Reader for more details on the operation
and function of Acrobat Reader.
Installing Acrobat Reader
Turn on your computer.
1
Insert the CD-ROM into the CD-ROM drive.
2
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
3
Windows95/98/Me/NT4.0/2000, double-click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
Double-click the "Acrobat" folder, and then double-click the
"ar500enu.exe" icon.
4
Follow the on-screen instructions to install Acrobat Reader.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
USING OTHER INSTALLED DRIVERS
If you use another GDI printer or a Windows Printing System printer, interference
between printers may occur and printing may not be performed properly. To use
another GDI printer or a Windows Printing System printer, you must change the port
setting of the printer driver using the following procedure.
If another printer does not operate properly when the Olivetti Personal
MFP Series printer driver is set to "FILE" as described below, uninstall
the Olivetti Personal MFP Series printer driver. To uninstall the printer
driver, see the online manual.
Click the "start" button.
1
Click "Control Panel", click "Printer and Other Hardware" and
then click "Printer and Faxes".
2
On Windows 95/98/Me/NT4.0/2000, select "Settings" and then click
"Printers".
Right-click the "Olivetti d-Copia 150D" icon in
the printer dialog box and then click
Olivetti d-Copia 150D
3
"Properties".
Click the "Ports" tab ("Details" tab - on
4
Windows 95/98/Me) in the "Properties" dialog box, select
"FILE": in the "Print to the following port" list box, and click the
"OK".
Right-click the icon of the printer to be used and click
"Properties".
5
Click the "Ports" tab ("Details" tab - on Windows 95/98/Me) in
the "Properties" window, select "LPT1" (or the currently used
6
port), and click the "OK" button.
To use the Olivetti Personal MFP Series again, perform the same
procedure but select the port to be used (for example, LPT1) in step 4.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE INTERFACE CABLE
This unit includes both USB and parallel interface connectors.
Interface cables for connecting the unit to your computer are not included with this
unit. Please purchase the appropriate cable for your computer.
• If you intend to use the unit as a scanner, it must be connected to
your computer with a USB interface cable. The scanner function
cannot be used if the unit is connected with a parallel cable.
• USB is available with a PC/AT compatible computer that was
originally equipped with USB and had Windows 98, Windows Me,
Windows 2000 Professional, Windows XP Professional or Windows
XP Home Edition preinstalled.
• Do not connect the interface cable before installing the MFP driver.
The interface cable should be connected during installation of the
MFP driver. (p.21)
Connecting the USB interface cable
Obtain a shielded USB interface cable.
1
4
Insert the cable into the USB interface
connector located on the rear of the
unit.
2
Insert the other end of the cable into the interface connector of
your computer, or the USB hub connected to your computer.
3
Connecting the parallel interface cable
Obtain an IEEE1284 shielded parallel interface cable.
1
Ensure that your computer and unit are turned off.
2
Insert the cable into the parallel
3
interface connector located on the
rear of the unit, and fasten with
clasps.
Insert the other end of the cable into
the interface connector of your computer.
4
45
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING COPIES
5
This chapter describes basic copying functions and some other copying functions.
The copier is equipped with a 1-page memory buffer. This memory allows the copier
to scan an original once only and make up to 99 copies. This feature allows for
improved workflow, reduced operating noise from the copier and reduced wear and
tear on the scanning mechanism. This feature provides for a higher reliability.
If the unit does not function properly during use, or if a function cannot
be used, see "TROUBLESHOOTING THE UNIT" (p.62).
COPY FLOW
1
Make sure that paper has been loaded in the paper tray (p.15) and
check the paper size (p.14).
If paper is not loaded, see page 15. If you are using the single bypass, check
the paper size and then proceed to the next step without loading paper.
2
Place the original.
If you are using the original table, see "Using the original table" (p.47).
If you are using the SPF, see "Using the SPF (p.48).
When copying onto A4 paper or a large size, pull out the paper output tray
extension.
3
Select the copy settings.
If you wish to copy using the initial settings (p.13), proceed to the next step.
To set the number of copies, see page 49.
To adjust the resolution and contrast settings, see page 50.
To enlarge or reduce the copy, see page 52.
To print on both sides of the paper, see page 53.
4 Start copying.
If you are using the single bypass
Press the start (
) key.
Do not press the start (
sheet of paper into the single bypass.
(Page 17)
) key. Insert a
Multiple copies are not possible
using the single bypass.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not insert paper in the single bypass when a copy job from the paper
tray is in progress. This will cause a misfeed.
• If you start a print job while a copy job is in progress, the print job will
begin when the copy job is completed.
• The scanning function cannot be used while a copy job is in progress.
About interrupt copying
If you press the start ( ) key to begin a copy job while a print job using the paper
tray is in progress, the copy job will begin automatically after the print data in the
unit's memory is printed (interrupt copying). When this is done, the print data
remaining in the computer is not sent to the unit. When the copy job ends, press the
clear (
) key twice, or press the ON LINE key once to change the unit to the online
state (p.31), or wait until the set auto clear time (p.56) elapses. The remaining print
data will be sent to the unit and printing will resume. Interrupt copying is not possible
during a print job using the single bypass.
ORIGINAL PLACEMENT
Using the original table
• The original table can read up to A4 original.
5
• Image loss 4 mm can occur at the leading and trailing edges of the
copies. Also image loss 4.5 mm in total can occur along the other
edges of the copies. It can be 6 mm (max.) at the trailing edge of the
second copy of two-sided copying.
• When copying a book or an original which has been folded or a
crumpled original, press down the original cover lightly. If the original
cover is not securely closed, the copies may be striped or blurred.
• The original cover can be simply lifted straight up and reattached to
allow copying of a large original (12 cpm model only)
Open the original cover/SPF, and place the original.
1
Place an original face down on the original table. Align it with
the original scale and the centering ( ) mark. Gently close the
2
original cover/SPF.
Original scale
mark
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a large original (12 cpm model only)
The original cover can be removed to allow copying of bulky objects.
Simply lift the original cover straight
up.
1
To reattach the original cover, reverse the above procedure.
2
Using the SPF
The SPF is designed to hold up to 30 originals measuring from A5 to A4 and
2
weighting from 52 to 90 g/m .
• Before feeding originals in the original feeder tray, be sure to remove
any staples or paper clips from them.
• Before placing curled or wavy originals into the original feeder tray, be
sure to flatten them. If not, original misfeeds may result.
• The SPF (
) indicator on the operation panel will light up. If this
indicator does not light up, the originals are not properly set or the
SPF is not properly closed.
• Badly damaged originals may misfeed in the SPF. It is recommended
that such originals be copied from the original table.
• Special originals such as transparency film should not be fed through
the SPF, but should be placed directly on the original table.
• Image loss (max. 4 mm) can occur at the leading and trailing edges of
the copies. Also image loss (max. 4.5 mm in total) can occur along the
other edges of the copies. It can be 6 mm (max.) at the trailing edge of
the second copy of two-sided copying.
• To stop continuous copying using the SPF, press the clear (
) key.
Make sure that no original is left on the original table.
1
2
Adjust the original guides to the size
of originals.
Set the originals face up in the
original feeder tray.
3
Original face up
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Stream feeding mode
The stream feeding mode allows easy operation of continuous copying from the
SPF. If the stream feeding mode has been enabled using user program No.4, the
SPF (
) indicator will blink approximately 5 seconds after the last original has
been fed by the SPF. While this indicator is blinking, any new originals placed in the
original feeder tray will be fed and copied automatically. If the stream feeding mode
has been disabled, the start (
) key must be pressed each time the originals are
set even immediately after completion of a copy run from the SPF. The default
setting of the stream feeding mode is "ON". See "USER PROGRAMS" (p.56).
SET THE COPY QUANTITY
Set the number of copies using the two copy quantity (
from the original table or from the SPF if installed.
,
) keys when copying
• Press the clear (
) key to clear an entry if a mistake is made.
• A single copy can be made with the initial setting, i.e., when "0" is
displayed.
• Press the right copy quantity key to set the unit digit
from 0 to 9. This key will not change the tens digit.
• Press the left copy quantity key to set the tens digit
from 1 to 9.
5
49
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPOSURE ADJUSTMENT/PHOTO COPYING
Exposure adjustment
Copy density adjustment is not required for most originals in the automatic exposure
mode. To adjust the copy density manually or to copy photographs, the exposure
level can be adjusted in two steps manually.
The copy resolution used for AUTO and MANUAL (
changed. (p.56)
) mode can be
Press the exposure mode selector key to
1
2
select the MANUAL (
) mode.
) mode or PHOTO
(
Use the light (
) and dark (
) keys to
adjust the exposure level. If exposure level 2
is selected, the two left-handmost indicators
for that level will light up simultaneously.
Also, if level 4 is selected, the two right-
handmost indicators for that level will light up
simultaneously.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic exposure adjustment
This automatic exposure level will remain in effect until you change it
again by this procedure.
The automatic exposure level can be adjusted to suit your copying needs. This level is
set for copying from the original table and copying from the SPF respectively.
When adjusting the automatic exposure level for copying from
the SPF, place an original in the original feeder tray and make
1
sure that the SPF (
) indicator lights up. When adjusting the
level for copying from the original table, make sure that no
original is left in the original feeder tray.
Press the exposure mode selector key to
2
3
select the photo (
) mode.
Press and hold down the exposure mode
selector key for approximately 5 seconds.
The photo (
) indicator will go out and the
5
AUTO indicator will begin to blink. One or
two exposure indicators corresponding to
the automatic exposure level which has
been selected will light up.
Press the light (
) or dark (
) key to
4
5
lighten or darken the automatic exposure
level as desired. If exposure level 2 is
selected, the two left-handmost indicators
for that level will light up simultaneously.
Also, if level 4 is selected, the two right-
handmost indicators for that level will light
up simultaneously.
Press the exposure selector key. The AUTO indicator will stop
blinking and light up steadily.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
REDUCTION/ENLARGEMENT/ZOOM
Three preset reduction ratios and two enlargement ratios can be selected. The zoom
function enables copy ratio selection from 25% to 400% in 1% increments.
Set the original and check the paper size.
1
Use the copy ratio selector key and/or zoom (
select the desired copy ratio.
,
) keys to
2
• To verify a zoom setting without changing the zoom ratio,
press and hold down the copy ratio display (%) key. When the
key is released, the display will return to the copy quantity
display.
• To reset the ratio to 100%, press the copy ratio selector key
repeatedly until the 100% indicator lights up.
Set the reduction/enlargement ratio.
3
To decrease or increase the zoom ratio rapidly, press and hold
down the (
) or (
) key. However the value will stop at the
preset reduction or enlargement ratios. To move beyond these
ratios, release the key and then press and hold it down again.
To select a preset copy ratio:
Preset reduction and enlargement ratios are:
25%, 70%, 86%, 141%, and 400%.
A5
A4
141
A4 B5
A4
86
70
A5
To select a zoom ratio:
When a zoom (
or
) key is pressed, the
A4
Zoom indicator will light up and the zoom ratio will
be displayed in the display.
B5
A5
A4
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FUNCTIONS
6
This chapter describes the special functions of this unit. Use these functions as
needed.
TWO SIDED COPYING
When copying from the SPF, two-sided originals can be copied automatically without
having to manually turn them over. Automatic two-sided copying can also be
performed without using the SPF. When copying from one-sided originals to two-
sided copies, copying orientation can be selected between Turn on Long Edge and
Turn on Short Edge.
• When making two-sided copies from the original table, the paper size
must be A4, letter. When making two-sided copies from the SPF, A4,
B5, A5, letter, legal, and invoice sizes can be used. Non-standard size
paper cannot be used.
• When using two-sided invoice size originals from the SPF, be sure to
place them in the landscape orientation. Otherwise, an original
misfeed will occur.
A
A
A
A
A A
A A
6
Turn on Long Edge
Making two-sided copies
Turn on Short Edge
Place the original on the original table or in the SPF. (see
"ORIGINAL PLACEMENT" (p.47).
1
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Select two-sided copy mode.
2
Use the original to copy key to select the desired one-sided to two-sided
copying mode (Turn on Long Edge or Turn on Short Edge). See the
illustrations on page 53.
Select the copy settings. See "SET THE COPY QUANTITY"
(p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.50),
and "REDUCTION/ENLARGEMENT/ZOOM" (p.52).
3
Using the original table
If you are using the original table, copying is only possible in one sided to
two-sided mode ("A" above).
Press the start ( ) key.
1
The original is scanned into the unit's memory.
Place the original that you wish to copy onto the rear side of the
paper, and press the start ( ) key again.
2
Copying begins.
Using the SPF
Press the start ( ) key. Copying begins in the selected two-sided copy mode.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (page 55)
Reduces toner consumption by approximately 10%.
Power save modes (page 56)
The unit has two power save modes of operation: preheat mode and auto power
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save ( ) indicator will light up
and other indicators will remain on or off as before. In this condition, the fuser in
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start ( ) key
using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save ( ) indicator
will light up and other indicators will go out. The auto power shut-off mode saves
more power than the preheat mode but requires a longer time before starting
copying. To copy from the auto power shut-off mode, press the start ( ) key.
Then make desired copier selections and press the start ( ) key using the
normal copying procedure.
Auto clear (page 56)
The unit returns to the initial settings a preset amount of time after the end of copy, or
scanner operation. This preset amount of time (auto clear time) can be changed.
Stream feeding mode (page 56)
For description of the stream feeding mode, see "Stream feeding mode" (p.49).
Resolution of AUTO & MANUAL mode (page 56)
You can set the copy resolution used for AUTO and MANUAL (
mode.
) exposure
6
TONER SAVE MODE
Press the exposure mode selector key to
1
select the manual (
) mode.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Press and hold down the exposure mode
selector key for approximately 5 seconds.
2
The MANUAL (
and the PHOTO (
) indicator will go out
) indicator will begin to
blink. The exposure indicator marked "5"
will light up, indicating the standard toner
mode is active.
To enter the toner save mode, press the
3
4
light (
) key. The exposure indicator
marked "1" will light up, indicating the
toner save mode is selected.
Press the exposure mode selector key. The PHOTO (
)
indicator will stop blinking and light up steadily. The light and
dark indicator marked "3" will light up. The toner save mode is
now active.
To return to the standard mode, repeat the procedure but use the dark
(
) key to select exposure level "5" in step 3.
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or
canceled as desired.
Setting the power save modes, auto clear time, stream
feeding mode and resolution of AUTO & MANUAL mode
Press and hold down the light (
simultaneously for more than 5 seconds until all the alarm
) and dark (
) keys
1
indicators (
,
,
) blink and "
" appears in the display.
Use the left copy quantity (
) key to select a user program
2
number (1: auto clear time, 2: preheat mode, 3: auto power
shut-off timer, 4: stream feeding mode, 5: auto power shut-off
mode 6: resolution of AUTO & MANUAL mode). The selected
number will blink in the left side of the display.
Press the start (
steadily lit and the currently selected parameter number for the
program will blink on the right side of the display.
) key. The entered program number will be
3
4
Select the desired parameter using the right copy quantity (
key. The entered parameter number will blink on the right of the
)
display.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Program
No.
Mode
Parameters
0
*3
OFF, 1
60sec., 4
10sec., 2
90sec., 5
30sec.
120sec.
1
2
3
Auto clear time
Preheat mode
*0
30sec., 1
60sec., 2
90sec.
15min.
Auto power shut- off
timer
0
3
2min., *1
30min. 4
5min., 2
60 min. 5
120min.
Stream feeding
mode
4
5
6
0
OFF, *1
OFF, *1
300dpi, 1
ON
Auto power shut- off
mode
0
ON
Resolution of AUTO
& MANUAL mode
*0
600dpi
* Factory default settings are indicated with an asterisk (*).
Press the start ( ) key. The right-hand number in the display
will be steadily lit and the entered value will be stored.
5
6
To change the setting or to set another mode, press the clear
(
) key. The unit will return to step 2.
Press the light (
copy mode.
) or dark (
) key to return to the normal
6
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press and hold down the clear ( ) key for approximately 5
seconds. The total number of copies will appear in two steps, each
with three digits.
Example: Total number of copies is 1,234.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
7
This chapter describes how to replace the TD cartridge and drum cartridge, and how
to clean the unit.
Be sure to use only genuine Olivetti parts and supplies.
TD CARTRIDGE REPLACEMENT
The TD cartridge replacement required ( ) indicator will light up when toner is
needed. For more information on purchasing the TD cartridge, see "ABOUT
SUPPLIES AND INTERFACE CABLES" (p.71). If copying is continued while the
indicator is lit, copies will gradually become lighter until the unit stops and the
indicator begins blinking. Replace the old TD cartridge by following the procedure
below.
• After the unit stops, it may be possible to make a few more copies by
taking the TD cartridge out of the unit, shaking it horizontally, then
reinstalling it. If copying is not possible after this operation, replace the
TD cartridge.
• During long copy run of a dark original, the start (
blink, the indicator light up, and the unit stop, even though toner is left.
The unit will feed toner up to 2 minutes and then the start (
indicator will light up. Press the start ( ) key to restart copying.
) indicator may
)
Open the side cover and front cover, in that order.
To open the side cover and front cover, see "INSTALLING THE TD
CARTRIDGE" (p.10).
1
2
Gently pull the TD cartridge out
while pressing the lock release
Lock release button
button.
Dispose of the old TD cartridge in accordance with local regulations.
Install a new TD cartridge. To install the new cartridge, see
"INSTALLING THE TD CARTRIDGE" (p.10).
3
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The
4
indicator will go out and the start (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies. When the internal
counter reaches approximately 17,000 copies, the drum replacement required (
)
indicator will light up indicating that replacement of the drum cartridge will be needed
soon. For more information on purchasing the drum cartridge, see "ABOUT SUPPLIES
AND INTERFACE CABLES" (p.71). When the indicator begins to blink, the unit will stop
operating until the cartridge is replaced. Replace the drum cartridge at this time.
Do not remove the protective cover on the drum portion (black paper) of
a new drum cartridge before use. The cover protects the drum against
external light.
Remove the TD cartridge (see "TD CARTRIDGE REPLACEMENT" (p.58).
1
Hold the drum cartridge handle and
gently pull the cartridge out. Dispose
of the old drum cartridge in
2
Drum cartridge handle
accordance with local regulations.
7
Remove the new drum cartridge from the protective bag and
remove the protective cover from the cartridge. Then gently
install the new drum cartridge.
3
• Do not touch the surface of the drum (green portion) of the
cartridge. Doing so may cause smudges on the copies.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Gently install the TD cartridge. To install the TD cartridge, see
"INSTALLING THE TD CARTRIDGE" (p.10).
4
5
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The drum
replacement required (
) indicator will go out and the start
(
) indicator will light up.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
CLEANING THE UNIT
Proper care is essential in order to get clean, sharp copies. Be sure to take a few
minutes to regularly clean the unit.
• Before cleaning, be sure to turn the power switch off and remove the
power cord from the outlet.
• Do not use thinner, benzene or other volatile cleaning agents. Doing
so may cause deformation, discoloration, deterioration or malfunction.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and the back side of the original cover/SPF
Stains on the glass, scanning window, cover or SPF roller will also be copied. Wipe
the glass, scanning window, cover and SPF roller with a soft, clean cloth. If
necessary, dampen the cloth with a glass cleaner.
Original table/scanning window
Original cover/SPF
SPF roller
Scanning window
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer charger
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean
the charger using the following procedure.
Turn the power switch off. (p.12)
1
Open the side cover while pressing the side cover open button.
2
Take the charger cleaner out by holding the tab. Set the charger
3
cleaner onto the right end of the transfer charger, gently slide
the cleaner to the left end, and then remove it. Repeat this
operation two or three times.
Slide the charger cleaner from the right end to the left end along
the groove of the transfer charger. If the cleaner is stopped on
the way, smudges on copies may occur.
Return the charger cleaner
4
to its original position.
Close the side cover by
pressing the round
7
projections near the side
cover open button.
Turn the power switch on. (p.12)
5
61
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING THE UNIT
8
This chapter describes misfeed removal and troubleshooting.
For problems with the printer function or the scanner function, see the online manual
or the Help file for the printer/scanner driver.
TROUBLESHOOTING
If any problem occurs, check the list below before contacting our Technical
Assistance Department.
Problem
Possible cause
Unit plugged in?
Power switch on?
Side cover closed securely? Gently close the side cover.
Front cover closed? Gently close the front cover and then
close the side cover.
Solution
Plug the unit into a grounded outlet.
Turn the power switch on.
Page
12
12
Unit does not
operate.
10
10
Is the original placed face Place the original face down on the
down on the original table original table or face up in the SPF.
or face up in the SPF?
Blank copies
47,48
Is original image too dark or Adjust the exposure manually.
too light?
Is the unit in the automatic Adjust the automatic exposure level.
50
51
50
60
Copies are too
dark or too light. exposure mode?
Is the unit in the photo
exposure mode?
Original table or original
cover dirty?
Cancel the photo exposure mode.
Clean regularly.
Dust, dirt,
smudges appear
Original smudged or
on copies.
Use a clean original.
–
blotchy?
Striped copies
Is transfer charger clean? Clean the transfer charger.
61
Non-standard paper used? Use standard paper. If using special
papers, feed the paper through the
single bypass.
14
Paper curled or damp?
Store paper flat in the wrapper in a
dry location.
–
Paper misfeeds
frequently.
Pieces of paper inside unit? Remove all pieces of misfed paper.
Paper guides in the paper Set the guides properly depending on
64
15
tray not set properly?
the paper size.
Too much paper in the
paper tray?
Is the paper too heavy?
Paper damp?
Remove excessive paper from the
tray.
Use paper within the specified range.
Replace with dry paper. If the unit is
not used for long time, remove the
paper from the paper tray and store it
in its wrapper in a dry location.
16
14
Images rub off the
copy easily.
72
62
Download from Www.Somanuals.com. All Manuals Search And Download.
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
Be sure to use only genuine OLIVETTI parts and supplies.
Indication
Cause and remedy
Page
Steadily Replacement of drum cartridge will be needed
71
lit
soon. Prepare a new cartridge.
Drum replacement
required indicator
Drum cartridge must be replaced. Replace it with
a new one.
Blinking
59
71
58
Steadily Replacement of TD cartridge will be needed
TD cartridge
lit
soon. Prepare a new cartridge.
replacement
TD cartridge must be replaced. Replace it with a
new one.
required indicator
Blinking
A misfeed has occurred. Remove the misfed
Blinking paper referring to the description of "MISFEED
REMOVAL".
Misfeed indicator
64
An original misfeed has occurred in the SPF.
Blinking Remove the misfed originals referring to the
description of "D: Misfeed in the SPF".
SPF misfeed
indicator
67
55
55
The unit is in the preheat mode. Press any key to
cancel the preheat mode.
Power save indicator is
steadily lit.
The unit is in the auto power shut-off mode.
Press the start ( ) key to cancel the auto power
shut-off mode.
The paper tray indicator is
blinking.
The paper tray is not installed properly. Push the
tray into the unit securely.
–
58
–
"CH" is blinking in the
display.
The TD cartridge is not installed. Check if the
cartridge is installed.
Side cover is open. Close the side cover
securely by pressing the round projections near
the side cover open button.
"CH" is steadily lit in the
display.
The paper tray is empty, or single bypass has
been selected in the printer function.
Load paper.
A misfeed has occurred in the paper tray or
single bypass. Remove the misfed paper.
15, 17
64
"P" is blinking in the display.
The scan head locking switch is locked. Unlock
the scan head locking switch and turn the power
switch off/on.
A letter and a number appear
alternately.
9
–
8
The unit will not function. Turn the power switch
A letter and a number appear off and then switch it on, and if there is again an
alternately.
error, remove the power cord from the outlet, and
contact your authorized service representative.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
MISFEED REMOVAL
When the misfeed ( ) indicator blinks or
blinks in the display, the unit will
stop because of a misfeed. If a misfeed occurs when using the SPF, a number may
appear in the display after a minus sign. This indicates the number of the originals
that must be returned to the original feeder tray after a misfeed. Return the required
number of originals. Then this number will disappear when copying is resumed or the
clear (
) key is pressed. When the SPF misfeeds an original sheet, the unit will
) indicator will blink, while the misfeed ( ) indicator
stop and the SPF misfeed (
will remain off. For a misfeed of originals in the SPF, see "D: Misfeed in the SPF"
(p.67).
Open the side cover.
To open the side cover, see "INSTALLING THE TD CARTRIDGE" (p.10).
1
Check the misfeed location. Remove the misfed paper
following the instructions for each location in the illustration
2
below. If
blinks in the display, proceed to "A: Misfeed in the
paper feed area" (p.65).
(p. 65)
(p. 66)
(p. 65)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
A: Misfeed in the paper feed area
Gently remove the misfed paper from the paper feed area as
1
shown in the illustration. When
blinks in the display and the
misfed paper is not seen from the paper feed area, pull out the
paper tray and remove the misfed paper. If the paper cannot be
removed, proceed to "B: Misfeed in the fusing area".
The fusing unit is hot. Do not touch the fusing unit when
removing misfed paper. Doing so may cause a burn or other
injury.
• Do not touch the surface of the drum (green portion) of the
drum cartridge when removing the misfed paper. Doing so
may damage the drum and cause smudges on copies.
• Toner on the paper may stain the paper transport area,
resulting in smudges on copies.
Close the side cover by pressing the round projections near
the side cover open button. The misfeed ( ) indicator will go
2
out and the start (
) indicator will light up.
B: Misfeed in the fusing area
Lower the fusing unit release
lever.
1
Fusing unit release lever
8
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Gently remove the misfed paper
from under the fusing unit as
shown in the illustration. If the
paper cannot be removed, proceed
to "C: Misfeed in the transport
area".
2
The fusing unit is hot. Do not
touch the fusing unit when
removing misfed paper. Doing
so may cause a burn or other
injury.
• Do not touch the surface of the drum (green portion) of the
drum cartridge when removing the misfed paper. Doing so
may cause smudges on copies.
• Do not remove the misfed paper from above the fusing unit.
Unfixed toner on the paper may stain the paper transport
area, resulting in smudges on copies.
Raise the fusing unit release lever and then close the side
cover by pressing the round projections near the side cover
open button. The misfeed ( ) indicator will go out and the start
3
(
) indicator will light up.
C: Misfeed in the transport area
Lower the fusing unit release lever.
1
See "B: Misfeed in the fusing area" (p.65).
Open the front cover.
2
To open the front cover, see "INSTALLING THE TD CARTRIDGE" (p.10).
Rotate the feeding roller in
3
the direction of the arrow
and gently remove the
misfed paper from the exit
area.
Feeding roller
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Raise the fusing unit release lever, close the front cover and
then close the side cover by pressing the round projections
near the side cover open button. The misfeed ( ) indicator will
4
go out and the start (
) indicator will light up.
Raise the fusing unit release lever, close the front cover and
then close the side cover by pressing the round projections near
the side cover open button. The misfeed ( ) indicator will go
out and the start (
) indicator will light up.
D: Misfeed in the SPF
An original misfeed may occur at one of three locations: if the misfed original is seen
from the original feeder tray, (A) in the original feeder tray; if the misfed original is not
seen from the original feeder tray, (B) in the exit area or (C) under the feeding roller.
Remove the misfed original following the instructions for each location.
(A) Open the feeding roller cover and pull the original gently to the left and out
from the original feeder tray. Close the feeding roller cover. Open and close
the original cover to clear the SPF misfeed (
) indicator. If the misfed
original cannot be easily removed, proceed to (C).
Feeding roller cover
8
67
Download from Www.Somanuals.com. All Manuals Search And Download.
(B) Open the original cover and rotate the roller rotating knob to remove the
misfed original from the exit area. If the misfed original cannot be easily
removed, proceed to (C).
Roller rotating knob
(C) If the original does not move easily into the exit area, remove it in the
direction of the arrow while rotating the knob.
A number may appear in the display after a minus sign, indicating the
number of the originals that must be returned to the original feeder tray.
Open and close the SPF to clear the SPF misfeed (
then clear the misfeed and return the required number of originals. Then
press the start ( ) key to resume copying.
) indicator and
68
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
9
SPECIFICATIONS
Model
12 cpm model
15 cpm model
Type
Digital multifunctional system, desk-top type
Dry, electrostatic transfer
Sheets, bound documents
Available
Copy system
Originals
Printer function
Scanner function
Paper tray
Available
250 sheets
Single bypass
SPF
Single bypass (1 sheet)
—
—
—
Available
Original table
SPF
A4/Legal
1 sheet
Original sizes
Original feed
A4/Legal
Original table
SPF
30 sheets max.
1
Copy/Printing size
A4 to A6 *
2
Max. 3 mm (Original table) *
2
Max. 4 mm (SPF) *
Image loss
3
Max. 4.5 mm *
4
Max. 6 mm *
Copy speed
12 pages/min.
15 pages/min.
Print speed
12 pages/min. (A4)
Continuous copying/printing
Max. 99 pages subtractive counter
5
First-copy/print time
(Approximately)
9.6 seconds *
(paper:A4, exposure mode:AUTO, copy ratio:100%)
Variable: 25% to 400% in 1% increments (total 376 steps)
Fixed: 25%, 70% 86%, 100%, 141%, 400%
Copy ratio
Moving optical source, slit exposure (stationary platen)
with automatic exposure
Original table
Exposure
system
SPF
—
Moving original
Fusing system
Development system
Light source
Heat rollers
Magnetic brush development
Cold cathode fluorescent lamp
600 x 1200dpi
Scanner
600 x 300dpi (Auto/Manual mode)
600 x 600dpi (Photo mode)
Resolution
Copier
9
Printer
Scan
600dpi
256 levels
Gradation
Output
2 levels
Bit depth
Sensor
1 bit or 8 bit/pixel
Colour CCD
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Scanning speed
12 cpm model
Max. 2.88 ms/line
16 MB
15 cpm model
Memory
Local voltage ±10% (For this copier power supply, see the
name plate located on the back of the unit)
Power supply
Power consumption
1000 W
Width (mm)
607.6
462.5
15.3 kg
518
607.6
492.5
16.9 kg
518
Overall
dimensions
Depth (mm)
6
Weight (Approximately) *
Width (mm)
Unit dimensions Depth (mm)
Height (mm)
462.5
295.6
492.5
380.4
Temperature: 10°C to 30°C
Operating conditions
Emulation
Humidity: 20% to 85%
GDI
IEEE1284-compliant bi-directional parallel interface/USB
interface (USB1.1 Standard)
Interface
Sound Power Level LwA (1B=10dB)
Copying: 6.0 [B], Standby: 3.7 [B]
Sound Pressure Level LpA (bystander positions)
Copying: 46 [dB (A)], Standby: 23 [dB (A)]
Noise emission measurement in accordance with ISO 7779.
Noise level
3
3
Emission concentration
(measurement according to
RAL-UZ 62)
Ozone: less than 0.02 mg/m
Dust: less than 0.075 mg/m
3
Styrene: less than 0.07 mg/m
1
* Feed paper lengthwise only.
2
* Leading and trailing edges.
3
* Along the other edges in totals.
4
* The trailing edge of the second (Two-sided copy mode).
5
* Data transmission time is not included. (Only for printer)
6
* Not including TD cartridge, drum cartridge and cables.
As a part of our policy of continuous improvement, OLIVETTI reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification figures
indicated are nominal values of production units. There may be some
deviation from these values in individual units.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT SUPPLIES AND INTERFACE CABLES
Be sure to use only genuine OLIVETTI parts and supplies.
For best copying results, be sure to use only OLIVETTI Genuine
Supplies which are designed, engineered, and tested to maximize the
life and performance of OLIVETTI copiers. Look for the Genuine
Supplies label on the toner package.
Supply list
Supply
Usable life
TD cartridge
Drum cartridge
Approx. 3,500 sheets *
Approx. 18,000 sheets
* Based on copying onto A4-type paper at 5% toned area
The machine comes with a TD cartridge whose life span is
approximately 2,000 sheets of paper.
Interface cable
Please purchase the appropriate cable for your computer.
Parallel interface cable
IEEE 1284-Shielded type bi-directional parallel interface cable (2m Max.)
USB interface cable
Shielded twisted pair cable, high-speed transmission equivalent (2m Max.)
9
71
Download from Www.Somanuals.com. All Manuals Search And Download.
MOVING AND STORING THE UNIT
Moving instructions
When moving the unit, follow the procedure below.
When moving this unit, be sure to remove the TD cartridge in advance.
Turn the power switch off and remove the power cord from the
outlet.
1
Open the side cover and front cover, in that order. Remove the
TD cartridge and close the front cover and side cover, in that
order.
2
To open and close the side cover and front cover, and to remove the TD
cartridge, see "TD CARTRIDGE REPLACEMENT" (p.58).
Raise the handle of the paper tray and pull the paper tray out
until it stops.
3
Push the center of the pressure plate down until it locks in
place and lock the plate using the pressure plate lock which
has been stored in the front of the paper tray.
4
Push the paper tray back into the unit.
5
Lock the scan head locking switch (p.9).
6
When shipping the unit, the scan head locking switch must be locked to
prevent shipping damage.
Close the paper output tray extension, and attach the packing
7
materials and tape which were removed during installation of
the unit. See "PREPARING THE UNIT FOR INSTALLATION"
(p.8).
Pack the unit into the carton. See "CHECKING PACKED
COMPONENTS AND ACCESSORIES" (p.8).
8
Proper storage
Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl or get
damp, resulting in paper misfeeds.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
D
Acrobat reader...................................43 Dark key ........................................ 6, 50
Alarm indicator
- Drum replacement required
Desktop Document Manager............. 19
Display................................................. 6
indicator.............................. 6, 59, 63 Displaying total number of copies ..... 57
- Misfeed indicator ................ 6, 63, 64 Disposing of TD cartridges................ 58
- TD cartridge replacement required
Drum cartridge................................... 59
indicator.............................. 6, 58, 63 Drum cartridge replacement.............. 59
Appendix ........................................... 69 Drum replacement required
Auto clear time ............................ 55, 56 indicator .................................. 6, 59, 63
Auto power shut-off mode ........... 55, 56
E
Automatic exposure adjustment ........ 51
Exposure adjustment......................... 50
Exposure indicator......................... 6, 50
B
Before installation.............................. 20 Exposure mode indicators ............ 6, 50
Button Manager........................... 19, 34 Exposure mode selector key ........ 6, 50
Bypass feed....................................... 17
F
Bypass paper guides............... 5, 17, 18
Flow of installation............................. 20
Front cover .......................................... 5
C
Cautions
Fusing unit release lever ............... 5, 65
- Handling .........................................2
- Using ..............................................1
Charger cleaner............................. 5, 61
Checking packed components and
accessories .........................................8
Cleaning the unit
- Cabinet......................................... 60
- Original cover ............................... 60
- Original table ................................ 60
- Scanning window ......................... 60
- SPF ..............................................60
- Transfer charger........................... 61
Clear key ................................. 6, 49, 57
Connecting the interface cable
- Parallel interface cable................. 45
- USB interface cable...................... 45
Conventions used in this manual and
online manual......................................4
Copy flow........................................... 46
Copy quantity .................................... 49
Copy quantity key.................... 6, 49, 56
Copy ratio display key ................... 6, 52
Copy ratio selector indicators........ 6, 52
Copy ratio selector key.................. 6, 52
H
Handle................................................. 5
Hardware and software
requirements ..................................... 19
How to print ....................................... 34
How to use the online manual........... 43
I
Indicators on the operation panel...... 31
Initial settings of operation panel....... 13
Installing the software.................. 19, 21
Installing the TD cartridge ................. 10
Interface
- Parallel interface........................... 45
- USB interface ............................... 45
Interface cable................................... 71
Interrupt copying................................ 47
Introduction.......................................... 4
L
Light key........................................ 6, 50
Loading paper ................................... 14
Loading the paper tray ...................... 15
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the unit for installation......... 8
Printer driver...................................... 19
Proper storage................................... 72
M
Making copies ...................................46
MFP driver
- Printer driver................................. 19
- Print Status Window..................... 19
- Scanner driver.............................. 19
Misfeed indicator ..................... 6, 63, 64
Misfeed removal
- Fusing area .................................. 65
- Paper feed area............................ 65
- SPF ..............................................67
- Transport area.............................. 66
Moving instructions............................ 72
R
Reduction/enlargement/zoom ........... 52
S
Scan head locking switch.................... 9
Scanner driver................................... 19
Scanner indicator .......................... 6, 31
SCANNER key .............................. 6, 39
Scanning from your computer ........... 40
Scanning with the "Scanner and
Camera Wizard"................................ 42
Setting up the unit ............................... 7
Setup procedure.................................. 7
Side cover ........................................... 5
Side cover open button ....................... 5
Single bypass.................................... 18
Software for the
Specifications .................................... 69
SPF ................................................... 48
SPF indicator................................. 6, 48
SPF misfeed indicator ................... 6, 67
Start indicator ................................ 6, 31
Start key .................................. 6, 46, 57
Status indicators................................ 63
Stream feeding mode............ 49, 55, 56
Supplies and interface cables ........... 71
Supply list
N
Name
- Operation panel..............................6
- Part names.....................................5
O
OLIVETTI MFP Personal Series........ 19
ON LINE indicator .........................6, 31
ON LINE key ................................. 6, 31
Online manual ...............................4, 43
Opening the printer driver
- Application.................................... 33
- Start menu.................................... 32
Opening the scan driver .................... 40
Operation panel...............................5, 6
Original placement
- Original table ................................ 47
- SPF ..............................................48
Original table ................................. 5, 47
Original to copy key....................... 6, 54
- Drum cartridge.............................. 71
- TD cartridge.................................. 71
T
TD cartridge................................. 10, 58
TD cartridge replacement.................. 58
TD cartridge replacement required
indicator................................... 6, 58, 63
Transfer charger............................ 5, 61
Troubleshooting................................. 62
Troubleshooting the unit.................... 62
Two sided copying............................. 53
P
Paper................................................. 14
Paper feed location indicator...............6
Paper output tray.................................5
Paper output tray extension ................5
Paper tray...................................... 5, 15
Parallel interface cable................ 45, 71
Photo copying.................................... 50
Power cord ..........................................5
Power off ........................................... 13
Power on ........................................... 12
Power save indicator ..................... 6, 31
Power switch ................................. 5, 12
Preheat mode.................................... 55
74
Download from Www.Somanuals.com. All Manuals Search And Download.
U
Z
USB interface cable..................... 45, 71 Zoom indicator................................... 52
Using other installed drivers.............. 44 Zoom key....................................... 6, 52
Using the manuals...............................4
Using the printer mode...................... 32
Using the scanner mode ................... 35
Using the OLIVETTI TWAIN.............. 41
INDEX BY PURPOSE
Checking the package.........................8 Removing paper jams
Cleaning the unit
- Fusing area .................................. 65
- Paper feed area............................ 65
- SPF .............................................. 67
- Transport area.............................. 66
- Cabinet......................................... 60
- Original cover ............................... 60
- Original table ................................ 60
- SPF ..............................................60 Replacing the drum cartridge ............ 59
- Transfer changer.......................... 61 Replacing the TD cartridge................ 60
Connecting the interface cable
Scanning
- Parallel interface cable................. 45
- USB interface cable...................... 45
Copying ............................................. 46
- Button Manager............................ 34
- Scanner and Camera Wizard....... 42
- OLIVETTI TWAIN......................... 41
Displaying total number of copies...... 57 Setting the copy quality
Enlarging/reducing copies................. 52
Installing the software
- Acrobat......................................... 43
- Auto.............................................. 51
- Manual.......................................... 50
- Photo............................................ 50
- Button Manager............................ 19 Setting the copy quantity................... 49
- MFP driver.................................... 19 Setting the toner save mode ............. 55
- Desktop Document Manager........ 19 Setting the user program................... 56
Installing the TD cartridge ................. 10 Setting up the Button Manager.......... 34
Loading paper
Storing the unit .................................. 72
- Paper tray..................................... 15 Two sided copying............................. 53
- Single bypass............................... 18 Using other installed drivers.............. 44
Loading the original
Using the online manual.................... 43
- Original table ................................ 47
- SPF ..............................................48
Moving the unit.................................. 72
Opening the printer driver..................32
Power off ........................................... 13
Power on ........................................... 12
Preparing for installation......................8
Printing ..............................................33
75
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE LICENSE
PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY
USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF
THIS LICENSE.
1. License.
The application, demonstration, system and other software accompanying this License, whether on disk,
in read only memory, or on any other media (the "Software") and related documentation are licensed to
you by OLIVETTI. You own the disk on which the Software is recorded but OLIVETTI and/or
OLIVETTI'S Licensors retain title to the Software and related documentation. This License allows you to
use the Software on one or more computers connected to a single printer and make one copy of the
Software in machine-readable form for backup purposes only. You must reproduce on such copy the
OLIVETTI copyright notice, the copyright notice of OLIVETTI’S Licensors and any other proprietary
legends of OLIVETTI and/or its Licensors that were on the original copy of the Software. You may also
transfer all your license rights in the software, the backup copy of the Software, the related
documentation and a copy of this License to another party, provided the other party reads and agrees to
the terms and conditions of this License.
2. Restrictions.
The Software contains copyrighted material, trade secrets and other proprietary material which is owned
by OLIVETTI and/or its Licensors and in order to protect them you may not decompile, reverse engineer,
disassemble or otherwise reduce the Software to a human-perceivable form. You may not modify,
network, rent, lease, loan, distribute or create derivative works based upon the Software in whole or in
part. You may not electronically transmit the Software from one computer to another or over a network.
3. Termination.
This license is effective until terminated. You may terminate this License at any time by destroying the
Software and related documentation and all copies thereof. This License will terminate immediately
without notice from OLIVETTI and/or OLIVETTI’S Licensors if you fail to comply with any provision
of this License. Upon termination you must destroy the Software and related documentation and all
copies thereof.
4. Export Law Assurances.
You agree and certify that neither the Software nor any other technical data received from OLIVETTI,
nor the direct product thereof, will be exported outside the United States except as authorized and as
permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by
you outside of the United States, you agree that you will not re-export the Software nor any other
technical data received from OLIVETTI, nor the direct product thereof, except as permitted by the laws
and regulations of the United States and the laws and the regulation of the jurisdiction in which you
obtained the Software.
5. Government End Users.
If you are acquiring the Software on behalf of any unit or agency of the United States Government, the
following provisions apply. The Government agrees:
(i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as
"Commercial Computer Software" and the Government is acquiring only "restricted rights" in the
Software and its documentation as that term is defined in Clause 252.227-7013 (c)(1) of the
DFARS; and
(ii) if the Software is supplied to any unit or agency of the United States Government other than DoD,
the Government's rights in the Software and its documentation will be as defined in Clause 52.227-
19 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52.227-86 (d) of the NASA
Supplement to the FAR.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Limited Warranty on Media.
OLIVETTI warrants the disks on which the Software is recorded to be free from defects in materials and
workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced
by a copy of the receipt. The entire liability of OLIVETTI and/or its Licensors and your exclusive
remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause
6. A disk will be replaced when it is returned to OLIVETTI or a OLIVETTI authorized representative
with a copy of the receipt. OLIVETTI will have no responsibility to replace a disk damaged by accident,
abuse or misapplication.
ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO NINETY (90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM JURISDICTION TO JURISDICTION.
7. Disclaimer of Warranty on Software.
You expressly acknowledge and agree that use of the Software is at your sole risk. The software and
related documentation are provided "AS IS" and without warranty of any kind and OLIVETTI and
OLIVETTI'S Licensor(s) (for the purpose of provisions 7 and 8, OLIVETTI and OLIVETTI'S
Licensor(s) shall be collectively referred to as "OLIVETTI") EXPRESSLY DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
OLIVETTI DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE
WILL MEET YOUR REQUIREMENTS, OR THAT THE OPERATION OF THE SOFTWARE WILL
BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE
CORRECTED. FURTHERMORE, OLIVETTI DOES NOT WARRANT OR MAKE ANY
REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE
SOFTWARE OR RELATED DOCUMENTATION IN TERMS OF THEIR CORRECTNESS,
ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR
ADVICE GIVEN BY OLIVETTI OR A OLIVETTI AUTHORIZED REPRESENTATIVE SHALL
CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU (AND NOT OLIVETTI OR A OLIVETTI
AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION, SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO
YOU.
8. Limitation of Liability.
UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE, SHALL OLIVETTI BE LIABLE FOR
ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE
USE OR INABILITY TO USE THE SOFTWARE OR RELATED DOCUMENTATION, EVEN IF
OLIVETTI OR AN OLIVETTI AUTHORIZED REPRESENTATIVE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
In no event shall OLIVETTI'S total liability to you for all damages, losses, and causes of action (whether
in contract, tort (including negligence) or otherwise) exceed the amount paid by you for the Software.
9. Controlling Law and Severability.
For a portion of the Software related with Apple Macintosh and Microsoft Windows, this license shall be governed
by and construed in accordance with the laws of the state of California and Washington, respectively. If for any
reason a court of competent jurisdiction finds any provision of this License, or portion thereof, to be unenforceable,
that provision of the License shall be enforced to the maximum extent permissible so as to effect the intent of the
parties, and the remainder of this License shall continue in full force and effect
.
10. Complete Agreement.
This License constitutes the entire agreement between the parties with respect to the use of the Software and
related documentation, and supersedes all prior or contemporaneous understandings or agreements, written
or oral, regarding such subject matter. No amendment to or modification of this License will be binding
unless in writing and signed by a duly authorized representative of OLIVETTI.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cod. 521905
Download from Www.Somanuals.com. All Manuals Search And Download.
|