Finisher Unit Installation Guide
Components
Step 1: Prepare the Printer
1. Turn the printer off (
!
) and disconnect the
power cord ( ) and interface cable (
"
#
).
2. Using a screwdriver, remove the breakout
panels on the side of the printer.
1
2
3
4
5
6
Finisher Unit
Finisher stand
Finisher Stacker
Finisher Cover
Power Cord
7
8
9
Inverter Stand
Clear Band
Band Stopper, Small
10 Band Stopper, Large
11 Metal Brackets
12 Cable (inverter to printer)
Inverter Unit
Not illustrated: Screws
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the two bottom caps:
a. Turn the inverter over.
3. Turn the inverter around and remove the
screws holding the metal brackets in place.
Keep the screws and brackets handy: they are
used to help secure the extension plate once it
is repositioned.
b. Remove the two screws securing the bottom
caps on either side of the inverter.
4. Turn the inverter around and remove the
two screws holding the extension plate.
Keep them handy to reattach the plate once
it is repositioned.
c. Remove the end caps and store them along
with the four screws in case you ever need
to convert the unit back.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Pull forward on the extension plate to
disengage the pins from the top channel stops,
then slide it down into the inverter and push
back to engage the pins on the bottom channel
stops.
7. Turn the inverter around and reinstall the
brackets.
Step 3: Assemble the Inverter
1. Place the hooks on the bottom of the
inverter into the slots on the inverter stand,
then slide the inverter to lock the hooks in
place.
6. Reattach the extension plate using the
screws you removed earlier.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the front of the inverter to the stand
using two screws on either side.
Step 4: Assemble the Finisher
1. Hook the finisher stand onto the inverter.
3. Attach the back of the inverter to the stand
using one screw on either side.
2. Attach the finisher stand to the inverter with
2 screws.
4. Attach the guard rail on the inverter stand to
the printer using 2 screws.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the finisher cover near the back of the
6. Place the large stopper over the tab on the
cover and turn it to lock it in position.
finisher. Locate the tab (!) on the right side of
the cover.
4. Hold the clear band perpendicular to the cover
and slip one end over the tab ( ), then pivot
) so that it is aimed
!
the band 90 degrees (
"
toward the finisher:
7. Attach the cover to the finisher and close it.
5. Slip the other end of the band (
the retainer on the finisher and secure it
with the small stopper ( ).
!) through
"
6
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Pull the finisher platform about half way out,
9. Position the finisher on the stand and attach
it with two screws from the back.
then loosen the screw on the locking piece (
!:
viewed from the opposite direction) so that it
drops through the slot below it. This keeps the
platform from moving while you attach the
finisher to it.
10. Lift the locking piece back up and tighten the
screw firmly. Be sure it’s out of the way and
the screw is tight—otherwise the platform
will not move freely.
11. Install the stacker, making sure the hooks
are firmly engaged and that the lever on the
finisher is positioned above the stacker (
!).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Secure the stacker with four screws.
Step 5: Make Connections
1. Connect the finisher’s cable to the inverter
(!
). Use the cable supplied to connect the
inverter to the printer ( ).
"
13. Push the finisher against the printer until the
prongs on the printer brackets fit into the
holes in the finisher.
2. Plug the power cord supplied into the
inverter, then connect it to a suitable
grounded outlet.
3. Reconnect the printer’s interface cable.
4. Plug in the printer’s power cord and turn on
the printer.
Note: If you need to, turn the levellers (
!) on
either side of the finisher to raise or
lower it so the holes and prongs align
properly. Make sure the finisher is level.
Note: When the printer is turned on, power
is supplied to both the printer and the
finisher.
58374501
Download from Www.Somanuals.com. All Manuals Search And Download.
|