OK-NIP10-A420
OK-NIP10-A420P
OK-NIP10-A420G – Wireless
OK-NIP10-A420GP – Wireless
PTZ X10 MPEG4/JPEG IP Camera
Quick Installation Guide
This guide describes the basic functions of
Network Camera with Pan/Tilt/Zoom.
All detailed information is described in the user’s manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not touch the Network Camera when it’s lightening.
Ϩʳ Do not disassemble the Network Camera.
Ϩʳ Do not drop the Network Camera.
Ϩʳ Do not manually pan and tilt the Network Camera when are power is on.
Ϩʳ Do not insert any object into the Network Camera, such as needles.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Check Package contents
Ϩʳ The Network Camera (Wire or Wireless model)
Ϩʳ Power adapter
Ϩ Camera stand
Ϩʳ A/V cable
Ϩ Antennas for wireless model only
Ϩʳ Software CD
Ϩ Remote controller
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Physical description
Ϩʳ Front panel
Antennas for wireless model only
Lens
Microphone
Status LEDs
Ϩ Rear panel
A/V
EXT I/O
External Mic..
Note the serial number from the label on the unit.
This serial number is the same as the Ethernet address.
for example:0002D1455282 =00-02-D1-45-52-82
Ethernet 10/100 RJ45 socket
Power cord socket
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Install your Network Camera in Ethernet network
Antennas for wireless model only
1. If you have external devices such as
sensors and alarms, make connection
form I/O terminal block.
*Refer to your user’s manual for the I/O
2. Use Ethernet cable to make connection
from Ethernet port to the hub.
*Use Category 5 Cross Cable when the
Network Camera is directly connected to
a PC.
3. Finally, connect power cord to a power outlet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Assign IP address
1. Run the “Installer Wizard” under the Software Utility directory from software CD.
2. The program will search the servers or cameras on the same LAN.
3. After searching, the main installer window
will pop up. Click on serial number that
matches the one you just note from
2. Physical description
4. Click “Link to selected device(s)” to
connect the Internet Explorer to the
Network Camera.
ϡIf there is no DHCP server on the LAN,
please refer to the user’s manual for the
methods of assigning an IP address.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The Internet Explorer Connects to the Network Camera
For setup further configuration, please check user’s manual on the software CD.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Client Settings (Windows XP/2000/Me/98SE)
At the initial access to the “Connection type” page in Windows, the web browser will ask
for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been
registered for certification and can be used to change the parameters at the client’s site.
The user may click on to install the plug-in. If the web browser does not allow the user to
complete the installation, check the Internet security to lower the security level or contact
your IT or networking supervisor.
1. Initial IE browser, select function item “Tools”-> “Internet Options”
2. Security-> Default Level
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lower down the security level bar to “Low”, and press “Apply”
4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X. press “Yes”.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Client Settings (Windows XP SP2)
1. Initial IE browser, select function item “Tools”Ш “Internet Options”
2. Security Ш”Custom Level”
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Security Settings Ш Download unsigned ActiveX Controls set “Enable” and press “OK”
4. Press “Apply” and then “OK”
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Key-In camera’s IP address and press “OK” on Information Bar.
6. Click the blue bar under the Camera’s IP address in the browser, then
choose “Install ActiveX Control”
7. Recover security settings. Download unsigned ActiveX Controls set
“Disable” and press “OK” and “Apply”
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|