Professional Disc Jockey Products
DM900EX
OWNER’S MANUAL
NUMARK INDUSTRIES
11 Helmsman Road, North Kingstown, RI 02852
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
NUMARK DM900 STEREO MIXER
INDEX
Introduction
Features
Page 2
Safety Information
Product Registration
Page 4
Precautions
Page 5
Page 6
Front Panel Diagram
Rear Panel Diagram
Guided Tour of Features
Operating Instructions
Page 7
Connection Diagram
Specifications
Page 9
Page 10
Page 11
Page 12
Block Diagram
Warranty and Service
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
5. Water and Moisture - This product should be
kept away from direct contact with liquids.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
6. Heat - Avoid placing this product too close to
any high heat sources such as radiators.
7. Power Sources - This product should be
connected to a power supply only of the type
described in these operating instructions, or as
marked on the unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE ANY COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
The lightning flash with arrowhead symbol within the
equilateral triangle is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within the equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying this appliance.
8. Power Cord Protection - Power supply
cords should be routed so that they are not likely to
be walked upon or pinched by items placed on or
against them. When removing the cord from a
power outlet be sure to remove it by holding the
plug attachment and not by pulling on the cord.
9. Object and Liquid Entry - Take care that
objects do not fall into and that liquids are not
spilled into the inside of the mixer.
CAUTION
FOR USA & CANADIAN MODELS ONLY
10. Damage Requiring Service - This product
should be serviced only by qualified personnel. If
you have any questions about service please
contact Numark at the number(s) shown on the
back cover of this manual.
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
11. Grounding or Polarization - Precautions
should be taken so that the grounding or
polarization means built into the mixer is not
defeated.
SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating
instructions should be read before this product is
connected and used.
NOTE: This apparatus does not exceed the
Class A/Class B (whichever is applicable) limits for
radio noise emissions from digital apparatus as set
out in the radio interference regulations of the
Canadian Department of Communications.
2. Retain Instructions - The safety and operating
instructions should be kept for future reference.
3. Heed Warnings - All warnings on this product and in
these operating instructions should be followed.
WARNING: To reduce the risk of fire or electric
shock, do not expose this appliance to rain or
moisture. Electrical equipment should NEVER be
kept or stored in damp environments.
4. Follow Instructions - All operating and other
instructions should be followed.
Please record the serial number of your unit as shown on the back of the chassis as well as the name of
the dealer from whom you purchased the unit. Retain this information for your records. Please return the
warranty card enclosed to register your mixer with us.
MODEL: DM900
PURCHASED FROM:_________________________
SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
IMPORTANT INFORMATION...
Please read this entire manual before
connecting the DM900 to your system.
For optimum performance:
SYSTEM PRECAUTIONS
• Always make sure that AC power is OFF while
making any connections.
• Use appropriate cables throughout your system:
Quality shielded audio cables and terminated
shielded video cables, low-capacitance preferred.
Speaker cables must be 14-gauge minimum; 12- or
10-gauge is better.
• Do not use excessively long cables (i.e. over
50ft/14m) Be sure plugs and jacks are tightly
mated. Loose connections can cause hum, noise or
intermittents that could easily damage your
speakers.
• Reliability will be enhanced through the use of
banana connectors on the speaker wires. Observe
correct speaker wire polarity. If in doubt, consult
your Numark dealer or a qualified technician.
• Never use spray cleaners on the slide controls.
Residues cause excessive dirt build-up and this
will void your warranty. In normal use slide controls
can last for many years. If they malfunction (usually
because of a dirty or dusty environment) consult a
professional technician.
• Take care to connect only one cable at a time. Pay
attention to the color-coded, labelled Input and
Output jacks.
• ALWAYS remember: “TURN AMPS ON LAST
AND OFF FIRST”. Begin with master faders or
volume controls on minimum and the amplifier
gain/input control(s) down. Wait 8 to 10 seconds
before turning up the volume. This prevents
transients which may cause severe speaker
damage.
• Never attempt to make any adjustments or repairs
other than those described in this manual. Take the
DM900 to your dealer or to an authorized Numark
Service Center.
• Use restraint when operating controls. Try to
move them slowly. Rapid adjustments could
damage speakers due to amplifier clipping.
A NOTE ON CABLES:
Make the input and output
connections with readily available
low-capacitance stereo cables.
Quality cable makes a big difference
in audio fidelity and punch. See your
Numark dealer or an electronics or
audio specialist store if you are not
sure which cables to get.
• Avoid amplifier “clipping” at all costs: this
occurs when the red LEDs (usually on the front
panel of most professional power amplifiers) start
flashing. “Clipping” is when the power amplifier is
distorting and working beyond it’s limits. Amplifier
distortion is THE major cause of speaker failure.
• To prevent fire or shock hazard, do not expose
the unit to rain or moisture. Never place cans of
beer, soda, glasses of water or anything wet
on top of the mixer!
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
DM9 0 0 EX FRONT PANEL DIAGRAM...
8
1
7
5
6
2
2
3
3
4
DM9 0 0 EX REAR PANEL DIAGRAM...
5
5
2
1
6
4
3
4
3
7
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
GUIDED TOUR OF FEATURES AND OPERATING INSTRUCTIONS...
CROSSFADER SECTION
If the DM900 is your first mixer, please read this entire
4. The Replaceable Crossfader achieves clean
manual before you begin operation.
segues between the two input channels.
If you are an experienced DJ, simply replace your old
mixer. The DM900 can be rack-mounted or used as a
free-standing unit (four 6" rack unit spaces).
"Hard left" selects Channel 1. "Hard right" selects
Channel 2. With the crossfader centered both assigned
channels are live. Use the crossfader for fast and
seamless segues from one selected channel to the
other.
INSTALLATION AND OPERATION
Note: The crossfader is user replaceable in case of
failure. Simply unscrew the two large screws which hold
it in place, lift it out and disconnect it’s cable. Re-attach
the new crossfader and screw the mounting plate back
onto the unit - you’re back in business!
Study the Connections Diagram on page 13. First,
connect all stereo input sources. Next connect your
monitor headphones. Make sure all faders are at "zero"
and the unit is off. Finally, connect the stereo outputs to
the power amplifier(s) and/or audio sources. Plug the
DM900 into it’s power supply and plug this into power.
Now you are ready to switch it on.
MONITOR SECTION
5. Channel Cue Assign. The Cue selector is used
to route channel audio to the Monitor Section. The
channel faders do not control the Cue volume.
1. Power Switch and Power-On LED.
The DM900 is divided into five functional blocks:
Input, Crossfader, Monitoring, and Master Output. It is
important to learn how each of these work.
6. Headphone Volume controls the output level to
the Headphone Jack located on the front panel of
the mixer. Connect headphones with a standard 1/4"
stereo plug. The Cue audio is sent to the headphone
amp using the Cue Assign Selector.
CHANNEL INPUTS SECTION
2. Channels 1 & 2 Input Toggle Switches select
which source will be live to that channel based on what
you have connected to the rear panel input section.
MASTER OUTPUT SECTION
7. The Stereo Master Fader controls the Master
output level.
3. The Input Faders are low-noise, low-impedance,
high-quality, smooth Alps™ faders. These control
individual source levels in the mix.
8. The LED METER indicates the Master output level.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
REAR PANEL: INPUTS AND OUTPUTS
(Please refer to diagram on page 7)
1. Power Input. Plug your external power supply into
here. See safety precautions on page 3 for proper
treatment of the power cord.
5. Line/Phono Input switch. Use this to allow line
level equipment to be plugged into your phono inputs
giving you a total of 8 line input options.
2. GND is the grounding lug for all turntables. Always
use this connection (your turntable cable should have a
grounding wire).
6. The Tape Outputs are low-impedance unbalanced
RCA jacks which output the program mix and allow you
to connect any recording device.
3. Phono Inputs on Channels 1, 2 and 3 use
unbalanced RCA jacks. Your input signal is fed directly
to the DM900's high-quality RIAA phono pre-amplifiers
so use this position only for moving magnet cartridges.
Line level sources will overload the sensitive phono pre-
amps and will sound very bad, so always be sure to
toggle the line/phono switch over to line before
connection of line sources.
7. The Stereo Master Outputs are low-impedance
RCA connectors controlled by the Master fader.
4. Channels 1 & 2 Line Inputs are unbalanced
RCA jacks. The Line Input is selected with the toggle
switch on the front panel.
You can connect stereo audio from HiFi VCRs, cassette
and reel-to-reel tape decks, DAT machines, CD players,
laser discs, tuners, even synthesizers or other mixing
consoles.
NOTE: Plug mono audio sources into both Left and
Right inputs using a “Y” cable connector.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
DM9 0 0 EX CONNECTION DIAGRAM...
Turnt able 2
Turnt able 1
Turnt able 3
CD Pla ye r
Po we r
Supply
Ma in
Tape Deck
Sound Syst e m
w/ Am p lifie r
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
SPECIFICATIONS...
INPUTS:
Line:
47kWinput impedance
100mV rms sensitivity (for 1.22 V output)
Phono: 47kWinput impedance
1.5 mV rms sensitivity @ 1 KHz (for 1.22 V output)
OUTPUTS:
Line:
7.2V rms max (+19 dBm)
Headphone Amp: .5 watt into 47W
Distortion less than .01%
SIGNAL TO NOISE RATIOS (vs. maximum output):
Line:
Better than 88 dB
Phono: Better than 78 dB
FREQUENCY RESPONSE:
Line:
20 Hz- 20k Hz +_ .5 dB
Phono: +_ 1 dB except for controlled attenuation of -3 dB
@ 20 Hz to reduce rumble and feedback
POWER CONSUMPTION:
8 Watt typical, 10 watt with full headphone output
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
DM9 0 0 EX
BLOCK DIAGRAM...
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 8 Num ark Indus t rie s
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Professional Disc Jockey Products
Wa rra n t y a n d Se rv ic e In fo rm a t io n
Numark Industries, LLC and Numark International, Inc. (hereafter “Numark”) warrants each
new product manufactured and/or supplied by it to be free from defects in material or
workmanship under conditions of normal use and service for 360 days, beginning on the date of
purchase from an authorized Numark Dealer, but not to exceed 2 years from date of shipment by
Numark.
The Numark obligation under this warranty is limited to repairing or replacing, at its option,
the product or part(s) therein; which upon examination by Numark shall appear to be defective
or not up to factory specifications; providing the Numark product is returned (transportation
prepaid) to Numark.
Numark shall not be liable for any damages, consequential or otherwise, resulting from the
use and operation of this product and makes no other warranty(s) either express or implied on
this product, including any warranty of merchantability.
This warranty does not extend to any of our products which have been subjected to
misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of
instructions furnished by us, nor extended to units which have been repaired or altered outside
of our factory, nor to cases where the serial number thereof has been removed, defaced, or
changed, nor to accessories used therewith not of our own manufacture. Numark reserves the
right to make changes or improvements in its products, during subsequent production, without
incurring the obligation to install such changes or improvements on previously manufactured
equipment.
To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD must
be returned to Numark Industries, LLC within thirty (30) days after date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.
EQUIPMENT TRANSPORT
A Return Authorization number should be obtained from Numark through the addresses or
phone numbers below.
It is the customer’s obligation, when returning faulty equipment, to properly pack the Numark
equipment in its original packaging. Failure to do so may inadequately protect the equipment in
transit and, therefore, jeopardize the customer’s warranty. The defective Numark equipment
should be sent, FREIGHT PREPAID with Return Authorization number to:
NUMARK INDUSTRIES
11 Helmsman Road
T e l e p h o n e : + 1 ( 4 0 1 ) 9 4 6 - 4 7 0 0
North Kingstown, RI 02852 U.S.A.
Attention: Service Department
Fax:
E-mail:
+ 1 ( 4 0 1 ) 9 4 6 - 5 3 5 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|