Professional Disc Jockey Products
DM 1885X STEREO MIXER
OWNER’S MANUAL
NUMARK INDUSTRIES
11 Helmsman Road, North Kingstown RI 02852
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
6. Heat - Avoid placing this product too close to
any high heat sources such as radiators.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
7. Power Sources - This product should be
connected to a power supply only of the type
described in these operating instructions, or as
marked on the unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE ANY COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
8. Power Cord Protection - Power supply cords
should be routed so that they are not likely to
be walked upon or pinched by items placed on
or against them. When removing the cord from a
power outlet be sure to remove it by holding the
plug attachment and not by pulling on the cord.
The lightning flash with arrowhead symbol within the
equilateral triangle is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
9. Object and Liquid Entry - Take care that
objects do not fall into and that liquids are not
spilled into the inside of the mixer.
The exclamation point within the equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying this appliance.
10. Damage Requiring Service - This product
should be serviced only by qualified personnel.
If you have any questions about service
please contact Numark at the number(s) shown
on the back cover of this manual.
CAUTION
FOR USA & CANADIAN MODELS ONLY
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
11. Grounding or Polarization - Precautions
should be taken so that the grounding or
polarization means built into the mixer is not
defeated.
S AFETY INS TRUCTIONS
12. Internal/External Voltage Selectors - Internal
or external voltage selector switches, if any,
should only be reset and re-equipped with a
proper plug for alternative voltage by a qualified
service technician. Do not attempt to alter this
yourself.
1. Read Instructions - All the safety and operating
instructions should be read before this product is
connected and used.
2. Retain Instructions - The safety and operating
instructions should be kept for future reference.
NOTE: This apparatus does not exceed the
Class A/Class B (whichever is applicable)
limits for radio noise emissions from digital
apparatus as set out in the radio interference
regulations of the Canadian Department of
Communications.
3. Heed Warnings - All warnings on this product and in
these operating instructions should be followed.
4. Follow Instructions - All operating and other
instructions should be followed.
WARNING: To reduce the risk of fire or electric
shock, do not expose this appliance to rain or
moisture. Electrical equipment should NEVER be
kept or stored in damp environments.
5. Water and Moisture - This product should be kept
away from direct contact with liquids.
Please record the serial number of your unit as shown on the back of the chassis as well as the name of the
dealer from whom you purchased the unit. Retain this information for your records. Please return the
warranty card enclosed to register your mixer with us.
MODEL: DM1885X
PURCHASED FROM:_________________________
SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
NUMARK DM1885X STEREO MIXER
INDEX
Safety Information
Page 3
Product Registration
Introduction and Features
Precautions
Page 5
Page 7
Front Panel Diagram
Sampler Operation
Rear Panel Diagram
Connection Instructions and Diagram
Specifications
Page 8
Page 10
Page 12
Page 13
Page 14
Page 15
Page 16
Block Diagram
Warranty and Service
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
CONGRATULATIONS!
You have purchased the DM1885X Stereo Mixer by Numark. This equipment features
the latestest in sampling technology. With all new circuitry you get 4 assignable memory
banks and editable sampling capability. You also get high quality audio output and
better reliability than ever before. TheDM1885X Preamp Mixer has been designed by
DJs for DJs. It gives you all of the controls and features you need in a professional piece
of equipment to dazzle the crowd.
Thank you for buying Numark DJ products!
FEATURES...
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
User replaceable assignable ALPs™ crossfader .
Bass, Mid,Treble,and Gain controls on every input channel.
Left<->Right Pan control on each channel and the DJ Mic.
Bass, Mid & Treble “KILL” switches for special effects and creative mixing.
Neutrik™ “Combo” connector allows 1/4” or XLR plug to be used for DJ Mic.
8 line inputs.
Three phono inputs switchable to line level.
Sends on each channel for easily hooking up external effects.
Pushbutton Cueing with PFL (pre-fader listen) on each channel.
Headphone monitoring with PFL/Program fader.
Master and 2 Zone outputs.
Stereo/Mono switch on the Master and Zones.
Balanced Outputs.
Tape Out for direct recording.
Powerful stereo headphone output.
High-end performance audio signal.
12V BNC light connector.
Digital Sampler features:
•
Advanced Digital Processor by “Analog
•Digital processor modes:
Devices” and DRAM memory provides true 16-
bit CD quality audio and powerful recording,
editing and playback options.
-Edit (allows Intro and/or Outro trimming of the
sample after it is recorded).
-Single (sample plays once).
•
Re-triggering for stuttering “rap”-style
-Repeat (loops sample until disengaged).
-Stutter (for "stutters" and "stabs" in single or
repeat mode).
effects.
•
•
Effect Level Fader.
Large Start-Stop button.
-Speed Control (plays sample faster or slower
than originally recorded resulting in frequency shift).
-Monitor (for monitoring sample with or without
program or cue audio output).
-Write (safely record a sample).
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DM 1 8 8 5 X
As a special bonus we have
included a right angle headhpone
adapter with this mixer.
Just plug your headphones into
the adapter and then plug the
adapter into your mixer.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
IMPORTANT INFORMATION...
Please read this entire manual before connecting the DM1885X to your system.
For optimum performance:
SYSTEM PRECAUTIONS
• Use appropriate cables throughout your
system: Quality shielded audio cables and
terminated shielded video cables, low-
capacitance preferred. Speaker cables must be
14-gauge minimum; 12- or 10-gauge is better.
• Reliability will be enhanced through the use
of banana connectors on the speaker wires.
Observe correct speaker wire polarity. If in
doubt, consult your Numark dealer or a qualified
technician.
• Always make sure that AC power is OFF
while making any connections.
• Do not use excessively long cables (i.e.
over 50ft/14m) Be sure plugs and jacks are
tightly mated. Loose connections can cause
hum, noise or intermittents that could easily
damage your speakers.
• Never use spray cleaners on the slide
controls. Residues cause excessive dirt build-
up and this will void your warranty. In normal
use slide controls can last for many years. If
they malfunction (usually because of a dirty or
dusty environment) consult a professional
technician.
• Take care to connect only one cable at a
time. Pay attention to the color-coded, labelled
Input and Output jacks.
• ALWAYS remember: “TURN AMPS ON
LAST AND OFF FIRST”. Begin with master
faders or volume controls on minimum and the
amplifier gain/input control(s) down. Wait 8 to 10
seconds before turning up the volume. This
prevents transients which may cause severe
speaker damage.
• Use restraint when operating controls. Try to
move them slowly. Rapid adjustments could
damage speakers due to amplifier clipping.
• Avoid amplifier “clipping” at all costs:
this occurs when the red LEDs (usually on the
front panel of most professional power
amplifiers) start flashing. “Clipping” is when
the power amplifier is distorting and working
beyond it’s limits. Amplifier distortion is THE
major cause of speaker failure.
• Never attempt to make any adjustments or
repairs other than those described in this
manual. Take the DM1885X to your dealer or to
an authorized Numark Service Center.
A NOTE ON CABLES:
Make the input and output connections
with readily available low-capacitance
stereo cables. Quality cable makes a
big difference in audio fidelity and
punch. Use balanced connections
whenever possible. See your Numark
dealer or an electronics or audio
specialist store if you are not sure which
cables to get.
• To prevent fire or shock hazard, do not
expose the unit to rain or moisture. Never
place cans of beer, soda, glasses of water
or anything wet on top of the mixer!
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DM 1 8 8 5 X
DM1 8 8 5 X FRONT PANEL DIAGRAM...
2 3
2 2
2 1
1
1 9
2 0
1 7
2
2 5
4
3
5
6
1 8
1 6
2 6
2 8
2 7
7
2 9
1 3
3 0
3 1
3 2
8
1 2
1 1
1 4
9
1 0
1 5
1. Channel Input Gain/Trim/Attenuation Controls.
These control the sensitivity of the inputs for Channels 1-4.
Use these whenever a particular source causes overload of
the preamp inputs. Attenuation range is 0dB to -20dB. Use
these with the PFL (pre-fader listen) monitor when cueing.
5. DJ Mic Talkover Switchhen engaged this mutes your
music sources from channels 1-4. Releasing it brings you
immediately back to full source level. It is very useful for
announcements.
6. Channels 1 - 4 Input Toggle Switches select which
source will be live to that channel based on what you have
connected to the rear panel input section.
2. Treble, Middle and Bass Controls fine tune the tone
of your music through the sound system. Note that these
are also available on the DJ Mic.
7.The Input Faders are low-noise, low-impedance, high-
quality, smooth faders. These control individual source
levels in the mix.
3.Use the Pan Control to maximize the Left or Right side of
your Source.
4. Send button will send the individual channel signal to the
onboard sampler and the send jack on the rear panel. This is
used to route to an external effects unit. The signal comes
back in from the effects unit through any line input channel
you select and is then sent out to your amplifier through the
Master Output jacks on the rear panel.
8. Channel Cue Assign/PFL pushbuttons are used to
route channel audio to the Monitor Section. The channel
input faders do not control the Cue volume. When the Cue
button is pushed you get Pre Fader Listen(PFL). In addition,
when these buttons are depressed the third row of the LED
meter (20) will display the signal level of that channel on a
PFL basis. The level can be adjusted by using the Gain
control (1).
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
9. The Crossfader In/Out Pushbutton defeats the
entire Crossfader function but leaves the Kill functions
active.
output while leaving the other frequencies playing. This area
is always active even when the crossfader is not. Try that for
a neat effect, or mix one channel’s treble with another
channel’s bass (by cutting the mid and bass on the first
channel and the treble and mid on the other channel.)
10. Crossfader/Kill Assign Switches lets you choose
which input channel will be heard when the Crossfader is
moved to the left or right and affected by the Kill function.
16. Master Level. This controls overall output level. Note that
you can select (18) whether you want stereo or mono.
11.The replaceable Crossfader achieves clean segues
between two selected input channels.
17. The Zone Levels control speaker volume for other outputs
such as control booth monitors, a tape deck, another
amplifier, a sub-woofer, another mixer or a satellite speaker
system. Note that you can select (18) whether you want
stereo or mono.
1 2 3 4
1 2 3 4
In this example, Channel 1 is selected on the Left and
Channel 3 is selected on the Right. With the Crossfader
centered both assigned channels are live. Use the
Crossfader for fast and seamless segues from one channel
to the next.
CONTRACTOR'S NOTE: Zone Level provides zone
control in installations where there are two separate rooms
(eg: a bar and a dance floor). The “Zone” volume should be
controlled from the mixer not from the amplifier.
18. The Stereo/Mono Toggle Switches allow you to select
Note: the crossfader is user replaceable. Simply unscrew
the two large screws which hold it in place, lift it out, and
disconnect its cable. Reattach the new crossfader and
screw it back onto the unit - you’re back in business!
REPLACEMENT CROSSFADERS can be purchased from
your local Numark Dealer, or by calling Numark Industries.
either stereo or mono output.
19. Stereo Auto Peak Hold Level Meter. The red LEDs for
+3, +5 and +8dB hold program peaks for an instant.
With peak metering, it's OK to be "in the red" as long as +5 or
+8dB isn't constantly lit. Set crossover, equalizer and power
amplifier inputs to avoid distortion at each step in the audio
chain. Proper attention to the peak meters results in the
punchiest possible sound without audible distortion.
12.The Cue Crossfader controls what signal is being
monitored through your headphones. Move the slide
control to the left and you will hear your source music from
the channel(s) selected with the cue/PFL switch. Move the
control to the right and you will hear your program mix, or
output. The slide control allows fast and frequent
headphone monitoring.
20. PFL Meter. When the Cue/PFL switches are depressed
this meter tracks pre-fader listen (PFL) signal for the channel
selected instead of the mixer’s output level.
21. 12V BNC Connector allows a 12 volt gooseneck style
13.The Headphone Level control sets the volume in your
“Numark” light to be connected directly to the mixer.
headphones.
22. The Power button turns the unit on and off. Make sure
your input faders (7) are turned down before you power up
your mixer.
14.The Headphone Jack accepts a 1/4” plug and is set on
the front of the unit.
15. Kill Switches and LEDs have been provided for
Treble, Mid and Bass Control on each side of the
23. The Mic Jack is a Neutrik™ “Combo Jack” and allows
connection of either a 1/4” jack or an XLR jack. This is ideal
for connecting an XLR Gooseneck directly.
crossfader. This allows you to mute that frequency’s audio
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DM 1 8 8 5 X
DIGITAL SAMPLER SECTION
TO RECORD A SAMPLE
The Sampler uses dynamic RAM with a 16-bit
microprocessor controller. The same digital signal
processing components used in professional audio
equipment deliver CD-quality samples.
a - Press the Write button once to go into stand by
mode. The red LED will go on.
b - Select the bank (or multiple banks) into which you want to
record. Any bank can be selected. Each bank contains 3
seconds of recording time. If you want to record a longer
sample select multiple banks (they must be adjoining). To
playback a multi-bank sample you must reselect the same
banks later. Note: To overwrite an existing sample,
select that bank instead of an empty bank. Changing bank
selection at this point in time is possible and will not destroy
any previously recorded samples.
25. The Mode Pushbuttons switch from effect to
effect. The accompanying LEDs illuminate to show you
which specific mode you are in at any time.
Modes are:
• Repeat sets the unit to play back a sample and
automatically repeat (loop) when it gets to the end of e - Hit the Start-Stop button to begin recording. It's red LED
the sample.
will light.
• Single sets the unit to play back a sample once.
f - Hit Start-Stop a second time to stop the sampling, or
allow the memory banks to fill up, at which time sampling will
stop automatically. Once your writing is complete the
sampler will automatically switch to Single playback mode
and light the Single LED. The sampler is now ready for
playback.
• Edit sets the unit to sample edit. This activates the
Intro and Outro editing controls as described in
#26. Edit can be used at the same time as Single
and Repeat so that editing of the sample can be
done while your program output is playing on the
dance floor.
26. Intro and Outro editing controls are used when Edit
mode is selected to fine tune the beginning (Intro) or
ending (Outro) of your samples. These "trim" the
• Write sets the unit to sampler record ready.
Depress the appropriate send button for the channel
you wish to record. Selecting a bank to record to and
hit the Start/Stop button (#30) to begin recording
(it is safer to actually choose your bank before going
to write mode so that you don't accidentally wipe out
an existing sample). The LED will stay lit while you are
in Write mode. After you are done writing your
sample you should select a play mode (either Single
or Loop) and listen to your sample - note that you
must do this manually by hitting the correct Mode
Pushbutton.
unwanted sound while in Single or Repeat playback
modes. Turn the controls inward to trim more - return them
to their full outside position to return to your full sample.
Once trimmed turn Edit off to lock-in your settings, now
every time you select the sample it will be the perfect
length. Note: Trimmed samples are not erased - they can
be heard again by going back into Edit and undoing the
trim. This powerful new feature allows you to start a sample
early or end it late and still trim it to the perfect length
without having to re-record. Since these controls can be
active while the sample is "live", you can even fine tune
samples on the fly. A way of efficiently trimming samples is
by engaging the Stutter button and repeatedly hitting the
Start-Stop button as you adjust the Intro knob.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
27. The Speed Control plays samples faster or slower
resulting in a pitch shift of the sample. In the center
position, the sample is played at recorded speed. Moving
the knob to the left will slow down playback by up to 50%;
moving the knob to the right will speed up the playback by
up to 200%. Positions near the center provide fine
changes in playback speed. Positions further from the
center detent provide more drastic changes in playback
speed.
• In Single or Repeat play with Trigger you are
ready to "stab" samples. With the Trigger Out, the
sample plays all the way through before you can play it
again. With it In, you can stab or stutter a sample.
When you shout "Rock it - rock the house!" and
sample it, it can be played back as -
R-R-R-R-R-R-R-Rock --
Rock-Rock-Rock it - Rock it Rock it -
Rock - - Rock it - rock the house!
28. Effect Level Mix fader. This precisely sets the audible
level of the sample in the mix.
by simply "drumming" with your fingers.
29. Memory Bank Select Pushbuttons A-D. Four
banks are available for storing samples. To record a bank
go to Write and then hit the bank button. You can record
into any combination of banks by pressing multiple bank
buttons.
31. The Stutter Pushbutton lets you choose
between two playback styles, Trigger and Non-
Trigger, when in Single or Repeat modes.
• When the Stutter is Out and the sampler is set to
Single or Repeat mode, each time you tap the
Start-Stop button the sample starts to play. The
next tap stops sample playback. The next time play
starts, the sample re-starts at the beginning.
After sampling, you can either select the next bank and
record it (remember Write is still on, just select the bank
and hit Start/Stop) or you can manually select a playback
mode.
• When the Stutter is In and the sampler is set to
Single or Repeat mode, each time you tap the Start-
Stop button the sample re-triggers.
You can play any combination of the Memory Banks from
left to right (that is, Memory Bank B will always play before
Memory Bank D - but you can play ABCD; BC; BD: ACD;
only C; only D; etc.).
ABOUT STUTTERING
Expensive studio rack-mount samplers and sampling
keyboards can re-trigger or stutter. This means
"beginning at the start of the sample each time a key
is pressed or a drum pad is struck".
30. The large Start-Stop button controls sample recording
and sample playback. The small red Effects Indicator LED
glows when the sampler is "on". Here are the functions:
• Tap the button when in sampler Write mode to begin
sampling (the LED will light). Tapping it again ends the
sample and the LED goes out. (unless the sampler has run
out of memory and shuts off automatically - Once the
Effects Indicator LED goes out, the Write LED goes
out and the Single LED turns on.
Re-triggering creates the stuttering "rap" effect. The
DM1685/1885 includes a manual stuttering
feature. How fast can you tap? Try using two fingers
for increased speed.
32. Monitor Pushbutton. To hear the sample or
effect in the headphones, press this button.
Program Mix still works and you will be able to hear
any other input channels with the Cue buttons
activated.
• In single or repeat play without Trigger, tap the button
to play the sample and tap it again to stop the playback.
Every time you play the sample, the music starts from the
beginning of the sample.
Numark - The Prove n Le ade r in DJ Te chnology
1 1
© 1 9 9 7 Num ark Indus t rie s
Download from Www.Somanuals.com. All Manuals Search And Download.
DM 1 8 8 5 X
DM1 8 8 5 X REAR PANEL DIAGRAM...
1 1
8
8
1 2
6
1 0
1
4
2
3 5
7 7 7 9 7 9 7
9
1. The Balanced Main Outputs are low-impedance XLR 8. Line/Phono Input switch. Use this to allow line level
type connectors controlled by the Master fader.
equipment to be plugged into your phono inputs giving
you a total of 8 line input options.
2. The Stereo Main Outputs are low-impedance RCA
connectors controlled by the Master fader.
9. Phono Inputs on Channels 1, 2 and 3 use
unbalanced RCA jacks. Your input signal is fed directly to
the DM1885X's high-quality RIAA phono preamplifiers
so use this position only for moving magnet cartridges.
Line level sources will overload the sensitive phono
preamps and will sound very bad, so always be sure to
toggle the line/phono switch over to line before
connection of line sources.
3. The Tape Outputs are low-impedance unbalanced RCA
jacks which output the program mix and allow you to
connect any recording device.
4. The Stereo Zone Outputs are low-impedance
unbalanced RCA jacks controlled by the Zone Level
controls.
10. AC Cord. See safety precautions on page 3 for proper
5. The Send can be attached to an external effects
treatment of the power cord.
processor such as a sampler.
11. Voltage Selector. Set this for the appropriate voltage
6. Mic is the mic input for the Mic Channel and Channel 4.
in your area
7. Channels 1-5 Line Inputs are unbalanced RCA jacks. 12. GND is the grounding lug for turntables 1, 2 and 3
The Line Input is selected with the toggle switch on the
front panel. You can connect stereo audio from HiFi
VCRs, cassette and reel-to-reel tape decks, DAT
machines, CD players, laser discs, tuners, even
synthesizers or other mixing consoles.
(phono inputs on Channels 1, 2 and 3). Always use this
connection (your turntable cable should have a
grounding wire).
NOTE: Plug mono audio sources into both Left and Right
inputs using a “Y” cable connector.
Numark - The Prove n Le ade r in DJ Te chnology
1 2
© 1 9 9 7 Num ark Indus t rie s
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
DM1885X Instructions for Connection and DIAGRAM...
Tape Deck
Zone 1
Sound Syst e m
w/ Am p lifie r
Sa m p ling
Keyboard
Turnt able 1
Zone 2
Sound Syst e m
w/ Am p lifie r
AC
Out le t
Microphone s
Turnt able 2
Turnt able 3
Tape Deck
Ma in
Sound Syst e m
w/ Am p lifie r
Dua l CD Pla ye r
CD Pla ye r
1. Be sure the POWER (22) is OFF. All connections should be made before the unit is turned on. Always remember
“Turn Amps on last and off first!”
2. Use appropriate cables throughout your system: quality shielded audio cables, low capacitance preferred. Speaker
cable must be 14-gauge minimum; 12- or 10-gauge is better.
3. Connect your music sources on the rear of the unit. Up to 3 phono and 8 line sources (CD players, cassette decks,
tuners, etc.) can be connected. When connecting to an input with a phono/line option switch remember to set the
switch accordingly.
4. Connect the ground wire from your turntables (and any other sources that come with a ground) to the ground post on
the rear panel. This will eliminate most common hum and feedback problems.
5. Connect your DJ mic on the front left side of the unit (23) or on the back of the unit at Mic 1. Connect your second mic at
Mic 2 on the back of the unit.
6. Connect your headphones on the front right side of the unit at (14).
7. The OUTPUT MASTER jacks on the rear of the unit are for connecting to the amplifier. Use the balanced outputs if
possible. Make sure you correctly attach the right and left cables to avoid phasing problems.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
DM 1 8 8 5 X
SPECIFICATIONS...
INPUTS:
SAMPLER:
Line:
10kWinput impedance
FREQUENCY RESPONSE AND SAMPLING RATE:
Variable sampling rate 44.1 kHz with 16-bit sampling yields
20Hz-22 kHz.
100 mV rms sensitivity (for 1.22 V output)
Mic:
10kWinput impedance balanced/unbalanced
3 mV rms sensitivity (for 1.22 V output)
50 mV rms max input
MAXIMUM MEMORY TIME:
12 seconds
Phono:
47kWinput impedance
1.5 mV rms sensitivity @ 1 KHz (for 1.22 V
output)
OUTPUTS:
Line:
9V rms max (+20 dBm)
Headphone Amp: 5 watt into 47W
Distortion less than .01%
SIGNAL TO NOISE RATIOS
(vs. maximum output):
Line:
Better than 82 dB
Better than 75 dB
Better than 75 dB
Mic:
Phono:
FREQUENCY RESPONSE:
Mic:
20 Hz- 15k Hz +_ .5 dB
Line:
20 Hz- 20k Hz +_ .5 dB
Phono:
+_ 1 dB except for controlled attenuation of -3 dB
@ 20 Hz to reduce rumble and feedback
CHANNEL EQ:
Bass:
±15db @80Hz
Middle:
Treble:
±10db @1KHz
±15db @12.5KHz
TALKOVER ATTENUATION:
Variable from no cut to -16 dB
KILL EFFECTS:
Bass: -54dB at 50 Hz, -3dB at 400 Hz
Middle: -44dB at 1k Hz, -3dB at 200Hz
Treble: -53dB at 15k Hz, -3dB at 2k Hz
POWER CONSUMPTION:
20 Watt typical, 28 watt with full headphone output
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
DM1 8 8 5 X
BLOCK DIAGRAM...
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Professional Disc Jockey Products
Wa r r a n t y a n d Se r v ic e In f o r m a t io n
Numark Industries, LLC and Numark International, Inc. (hereafter “Numark”) warrants each
new product manufactured and/or supplied by it to be free from defects in material or
workmanship under conditions of normal use and service for 360 days, beginning on the date of
purchase from an authorized Numark Dealer, but not to exceed 2 years from date of shipment
by Numark.
The Numark obligation under this warranty is limited to repairing or replacing, at its option,
the product or part(s) therein; which upon examination by Numark shall appear to be defective
or not up to factory specifications; providing the Numark product is returned (transportation
prepaid) to Numark.
Numark shall not be liable for any damages, consequential or otherwise, resulting from the
use and operation of this product and makes no other warranty(s) either express or implied on
this product, including any warranty of merchantability.
This warranty does not extend to any of our products which have been subjected to
misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of
instructions furnished by us, nor extended to units which have been repaired or altered outside
of our factory, nor to cases where the serial number thereof has been removed, defaced, or
changed, nor to accessories used therewith not of our own manufacture. Numark reserves the
right to make changes or improvements in its products, during subsequent production, without
incurring the obligation to install such changes or improvements on previously manufactured
equipment.
To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD
must be returned to Numark Industries, LLC within thirty (30) days after date of purchase.This
warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.Some states do not allow the exclusion or limitation of incidental or consequential
damages so the above limitation or exclusion may not apply to you.
EQUIPMENT TRANSPORT
A Return Authorization number should be obtained from Numark through the addresses or
phone numbers below.
It is the customer’s obligation, when returning faulty equipment, to properly pack the
Numark equipment in its original packaging. Failure to do so may inadequately protect the
equipment in transit and, therefore, jeopardize the customer’s warranty. The defective Numark
equipment should be sent, FREIGHT PREPAID with Return Authorization number to:
NUMARK INDUSTRIES
11 Helmsman Road
Telephone: +1 (401) 295-9000
North Kinstown, RI 02852 USA
Attention: Service Department
Fax:
E-mail:
+1 (401) 295-5200
Download from Www.Somanuals.com. All Manuals Search And Download.
|