CDN 36
PROFESSIONAL DUAL CD PLAYER
OWNER’S MANUAL
©2002
Industries
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
®
CDN 36
PROFESSIONAL DUAL CD PLAYER
CONGRATULATIONS...
You have just purchased a CD player designed specifically for the professional DJ. This unit has
been designed to provide CD mixing with ease and creativity that maximizes your skills. Please take a few
moments to familiarize yourself with the CDN 36 by reading the following information before attempting to
operate the unit.
Once again, congratulations and thank you for making the CDN 36 your choice in professional CD
players.
FEATURES:
•
•
•
•
Scratch, reverse, and filter modes
Seamless looping with stuttering
Anti-Shock™ buffer with true instant start
Interactive pitch/search/scratch wheel
design
BPM counter, ±8/16% pitch
High speed rotary track access and
sequence programming
•
•
•
•
•
•
Back-lit rubber buttons
Relay play and fader/remote start
Sleep mode to extend laser life
Transport bay illumination light
CDR compatible, digital output
Power switch protector
•
•
CHECK TO BE SURE
THE FOLLOWING ITEMS ARE IN THIS BOX:
CD PLAYER TRANSPORT UNIT
CD PLAYER CONTROL UNIT
OWNERS MANUAL (THIS
BOOKLET)
IEC POWER CORD (1 set)
CONTROL CABLE (2 sets)
RCA CONNECTING CABLES (2 pair)
FADER START CABLE (2 sets)
Please record the serial number of your unit as shown on the back of the chassis as well as the name of
the dealer from whom you purchased the unit. Retain this information and your original purchase
receipt for your records. Please return the enclosed warranty card to register your CD player with us.
MODEL: CDN-36
SERIAL NUMBER:
PURCHASED FROM:
DATE OF PURCHASE:
- The Leader in DJ Technology
©2002 Numark Industries
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
TABLE OF CONTENTS
Safety Instructions
2
3
5
Introduction and Registration
Set-up & Connections
Description of the Features
Face Panel
6
8
9
Rear Panel
Display
Basic Operation
Play, Pause and Cue Operations
Relay Play, Fader Start, Remote Switch Start
Looping
BPM Counter
Matching the Tempo
Beat Matching Using Pitch Bend
Example of Mixing
10
11
12
15
16
16
17
Before Switching off the Power
Troubleshooting Guide
Information and Specifications
Warranty
18
18
19
20
- The Leader in DJ Technology
©2002 Numark Industries
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
SETUP & CONNECTIONS
Typical connection with a mixer is illustrated below.
1. Mount the units in your console or rack with 19” EIA rails.
2. The transport should be mounted not to exceed an angle of 15 degrees.
3. Your CD player can be affected by excess vibration so mount the units in a
secure environment if possible.
4. Connect the supplied Control Cables between the CD Remote and CD Transport
unit. Note: Be careful to attach the marked connection jacks together, (yellow
–yellow and black-black)
5. Connect the line output connections using the supplied audio cables from the
CD Player to the line inputs of your mixer.
6. Connect Fader start cable. Attach your CD play to a similarly equipped DJ
mixer.
(This connection can also be used with a remote switch)
7. Connect IEC power cord to appropriate power source.
115V
230V
LINE VOLTAGE SELECTION
1) The desired voltage may be set with the VOLTAGE SELECTOR switch on the rear panel of the unit.
2) Do not move the VOLTAGE SELECTOR switch with excessive force as this may cause damage.
3) If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman.
DIGITAL OUTPUTS
This CD player is specially equipped with digital outputs. The format is type 2, form 1, also known as
S/PDIF (Sony/Phillips Digital Interface Format). When the digital output is used the variable pitch slider
and pitch bend buttons or pitch wheel should not be used.
Note: If digital information is allowed to change in pitch, other devices may not read the digital output
properly.
- The Leader in DJ Technology
©2002 Numark Industries
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
FRONT PANEL FEATURES
1. Open/Close: Press to load or eject the disc. The tray will not open if a disc is in play. The tray door will
automatically close in 30 seconds if left open. This is to protect the tray from accidental damage while open.
2. Single: Allows the unit to play back just one track at a time (single) or play continuously through all tracks and
then start over repeating the CD infinitely (continuous).
3. Time: Switches the time modes on the display between elapsed playing time, remaining time on the track, and
remaining time on the total CD. When toggled to remaining time total the total number of remaining tracks will
also show.
4. LCD Display: Indicates all the functions, as they are occurring, with the CD.
5. Track Knob: Rotate this knob to select tracks.
6. Program: Depress this button, the unit will stop and the program indicator will light. Select each track to be
programmed and press the PROGRAM button between selections. You can program up to 30 tracks. Press PLAY
to start the program. To exit and erase program hold the program button down for more than 2 seconds while
the unit is stopped, open the disc tray, or turn off the power.
7. Search Knob: Pressing the track knob allows you to use the jog wheel and rapidly scan the music to find a cue
point. The search function automatically shuts off after 8 seconds of non-use or you may toggle it off.
8. LOOP IN - Used for setting a start loop point and new cue points during play.
9. LOOP OUT - Used for setting the end loop point and releasing the loop action.
10. RELOOP/STUTTER - Depending on mode, as explained further, this button is used for either repeating a
previously set loop or seamlessly stuttering on the last set cue point.
11. Cue: Returns and pauses the music at the last set cue point. The cue point is where the music will begin when
play is pressed. The cue point is set as the initial start point on a track or can be moved when play is started at a
different point. For instance if the music is paused then play is pressed a new cue point is set. You can easily
edit the cue point by turning the wheel during pause. As you rotate the wheel the music will sound. By stopping
the wheel and pressing play a new point is set. Alternately pressing the PLAY button and the CUE button allows
the CD to be played from the same position any number of times.
Note: Pressing cue 2 times plays music temporarily from this point until the button is released.
12. Play/Pause: Starts the music from the cue point or pauses it while in play. By pressing play after pause a new
cue point will be set
- The Leader in DJ Technology
©2002 Numark Industries
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
13. Jog Wheel:
Cue Function: As explained under “CUE”, when the music is paused and you rotate the wheel, music will sound.
By pressing play a new cue point is set.
Search Function: As explained under “SEARCH KNOB”, when search is pressed and you rotate the wheel, the
music will rapidly scan the music to find a cue point.
Pitch Bend Function: allows the user to temporarily change the speed of the music to align beats. When the
beats of the music of the CD you wish to match are fast compared to the tempo of the other music, rotate the jog
wheel counter clockwise (to the left). When the CD is behind, rotate the jog wheel clockwise (to the right). The
pitch changes temporarily while the jog wheel is rotated. The faster you rotate the wheel the more pitch is
changed. Releasing the wheel results in a return to the original pitch.
Effect Function: When an effect button is pressed, this wheel can alter the sound of the effect.
14. Pitch Range: actives the pitch slider and adjusts the amount of control the pitch slider has on the overall speed
of music. Tapping the pitch will toggle slider between 8% and 16% pitch ranges. Holding the pitch for 3 seconds
will deactivate the pitch control.
15. Pitch Bend Buttons: Allows the user to temporarily change the speed of the music to align beats. When the
beats of the music of the CD you wish to match are fast compared to the tempo of the other music press the (-).
When the CD is behind press the (+). The pitch changes temporarily while the (+) or (-) button is being pressed.
The longer you hold the buttons the more pitch is changed. Releasing the buttons results in a return to the
original pitch.
16. Pitch Range LEDs: indicate current pitch range. When both LEDs are off, the pitch slider is not active
17. Pitch Slider: By moving the slider in the (+) direction the speed of the music permanently speeds up. By moving
the slider in the (-) direction the speed of the music permanently slows down. To match the speeds of two CDs
you can adjust the pitch. When the tempo of the music of the CD you wish to match is slow compared to the
tempo of the other music, move the slider to the (+) side and match the speed. When faster, move the pitch
slider to the (-) side. By making this adjustment, the speeds will be matched, though the beats may not yet be
aligned.
18. BPM: Switches the numeric display between pitch and BPM.
19. TAP: Tapping this button with the beat of the music indicates the current Beats Per Minute (BPM) in the display.
The unit will average your taps to determine the BPM so multiple taps are recommended.
20. Relay – Pressing this button will cause the sides of the unit to alternate play as one stops and the other starts. If
the players are set to single play mode then relay will alternate after each track. If the players are set to
continuous it will relay after the entire CD is played.
21. Scratch- This effect makes it possible for the wheel to scratch the music while it is playing. If you move the
wheel back and forth the music will stop and play slowly as the wheel is moved similar to scratching a record.
When the wheel stops moving the music will continue onward. You can also push the wheel forward and the unit
will automatically play as it slows. This effect can be left on to allow scratch style cueing of your music.
22. Reverse- This actually plays the music backwards. When the effect is activated the music will play backwards
until it is released.
23. Filter- This filter lets you play different frequencies of the music. Rotation of the wheel moves the frequency
played through the audio spectrum. If you turn off the effect then on again it remembers the last set parameter.
24. CD Drawer: Place your CDs you wish to play in here. This unit is designed to play commercially available CD and
properly burned and finalized CDR formats. Due to variances on the specification of certain CD burners and CDs
some home made CDs may not play properly.
25. Power Switch: Turn on and turn off the machine with this button. The unit should always be shut down with this
button first before any external power is removed.
- The Leader in DJ Technology
©2002 Numark Industries
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
REAR PANEL FEATURES
26. Control Cable Connector- Plug in the 8-pin cable included in here to connect the remote control and main CD
unit together
27. IEC Power Plug Connector - Plug your supplied power cord in here.
28. Voltage Selector - Set this switch to the voltage for your location.
29. RCA Audio Connectors - Connect your CD player to your mixer from this line level output.
30. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In
order to use the digital output you should not use variable pitch slider and the pitch bend buttons. If you adjust
the pitch, other devices may not read the digital output properly because the sampling rate changes
31. Remote Start Connector – Use this connector to plug into your fader start compatible mixer or remote switch.
This function is always active. To use this connector for fader start, connect the supplied fader start cable to a
fader start compatible mixer. Every time you move the crossfader on the mixer over to the side that the unit is
on, it will automatically start playing. When you move the fader away from that side, the unit will stop. Moving
the fader back to the unit side will start play again.
There are two potential modes associated with the switch PLAY-CUE and PLAY/PAUSE. The factory setting is
PLAY-CUE mode. This means that when the unit is remotely stopped it will go back to the cue point automatically.
To change modes hold down the time button for 3 seconds and the display will flash the play “
" and pause “
” icons. In PLAY/PAUSE mode, moving the crossfader away from the unit side pauses right where it is, and
resumes when the fader is brought back to the unit. To change modes back to PLAY-CUE hold down the time
button for 3 seconds and the display will flash the play “
" and cue “
” icons in the display.
32. Remote Assignment Switch - Set this switch in the position for the method of remote start you will be using.
Foot switches are often used for creative mixing techniques and can be found in most music shops. Connector
plugs are often ¼” and an adapter to 1/8” will be needed for connection. There are also two types of footswitches
that will work with this connector. The first is a typical, on/off pushbutton switch and are generally used for
switching channels on guitar amps. The second switch is a momentary footswitch and is usually used for
keyboard sustain pedals. If you are unsure of the style of switch you have, try each position until it works as
desired.
•
•
•
ON-OFF – for use with an ON-OFF switch.
MOMENTARY – for use with a momentary style of switch.
MIXER – for use with a fader start compatible DJ mixer
- The Leader in DJ Technology
- 8 -
©2002 Numark Industries
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
DISPLAY FEATURES
1. CUE - Flashing when the unit is setting a cue point. Lit continuously when the unit is paused at a cue
point.
2. PAUSE (II)- Active when the unit is paused.
3. PLAY (>)- Active while the unit is actually playing a CD.
4. TRACK - Shows the track that the unit is playing.
5. TOTAL – indicates when total CD remaining tracks are displayed.
6. MINUTES - Shows the minutes elapsed or remaining depending on mode setting.
7. SECONDS - Shows the seconds elapsed or remaining depending on mode setting.
8. FRAMES - The CD Player breaks down a second into 75 frames for accurate cueing. This shows the
frames elapsed or remaining depending on mode setting.
9. PROGRAM - Used for preprogramming the track order to be played automatically by the unit. This is a
great function if you need to leave the CD player alone.
10. AUTOSTART – will light when the unit is set to relay from CD unit to CD unit.
11. CONTINUOUS PLAY – Shows when the unit is set to play back the entire CD without stopping between
tracks.
12. SINGLE PLAY- Shows when the unit is set to play just one track at a time.
13. CD IN – indicates a standard CD is in the unit.
14. TIME BAR - Shows either track elapsed time, remaining track time, or remaining total time depending on
the setting of the “time” button.
TIME MODE -
15. (Remain) indicates when track remain time is displayed.
16. (Total) indicates when total CD remain time is displayed
note: if both indications are not lit, the unit will be showing “elapsed” time
17. SEARCH – indicates when the unit is searching through the music
18. NUMERIC DISPLAY - indicating either current pitch or BPM
19. PITCH - is lit when pitch is being displayed
20. BPM – is lit when BPM is being displayed
21. LOOP INDICATOR – Activates as loops are playing
- The Leader in DJ Technology
©2002 Numark Industries
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
DESCRIPTION OF THE PLAY/PAUSE AND CUE OPERATIONS
PLAY & CUE
Pressing the “PLAY/PAUSE” button starts the disc. Pressing the “CUE” button will reset the disc to the last place where
the disc was started. This is called the cue point. By alternately pressing the “PLAY/PAUSE” button and the “CUE”
button, the disc may be returned and played from the cue point any number of times. This function is called back
cue.
PLAY, PAUSE & CUE
When Play is paused and then started again, the return position for the back cue will be updated as the new cue point
EDITING CUE POINT
When the jog wheel is turned while a cue point is set, a new cue point can be located. The CD player will repeatedly
play small parts of the CD as you move it to the desired position. By pressing “PLAY/PAUSE” then “CUE” you can
confirm that this new cue point is desirable.
- The Leader in DJ Technology
©2002 Numark Industries
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
RELAY PLAY
1. Insert CDs into both of the units.
2. Press the “RELAY” button.
3. Press play on the first unit. When that unit stops play it will send a signal to the second unit to start play. You
will see the second unit start play and the first unit pause. When unit 2 has completed play unit 1 will start.
Note: The play signal is sent at the end of specified play. If the unit is in SINGLE mode the play signal will
start the second unit at the end of the track. If the unit is in CONTINUOUS mode the play signal will be
sent at the end of the full CD. Two CDs will play continuously, alternating from unit to unit.
FADER START
Fader Start is achievable by attaching your CD player to a similarly equipped DJ mixer and setting the rear panel
selection switch to “mixer” mode.
1. Connect cables between the CD player and your DJ mixer.
2. Press the button or switch on your mixer into fader start mode to activate the fader start capability.
3. Typically if you move the crossfader toward the active channel, the attached CD player will activate. When it is
moved away the unit will cue or pause depending upon CD player setting.
To select start/stop mode hold the time button for 3 seconds.
If the display shows
If the display shows
then the CD will pause when the crossfader is moved away.
then the CD will CUE when the crossfader is moved away.
REMOTE SWITCH START
Remote switch start is achievable by attaching your CD player to a switch like a foot switch found in most music
shops. Foot switch connector plugs are often ¼” and an adapter to 1/8” will be needed for connection.
1. Connect the remote switch to your CD player.
2. Select the type of foot switch you will use. There are two types of footswitches that will work with this connector.
The first is a typical, ON-OFF pushbutton switch and are generally used for switching channels on guitar amps.
The second switch is a momentary footswitch and is usually used for keyboard sustain pedals. If you are unsure
of the style of switch you have, try each position until it works as desired.
3. Typically if you press the switch once, the attached CD player will activate. When it is pressed again the unit will
cue or pause depending upon CD player setting.
Note: You can also use a momentary switch in the ON-OFF switch position. In this case the unit will only
play while the switch is depressed. When the button is release it will either cue or pause depending upon
mode.
- The Leader in DJ Technology
©2002 Numark Industries
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
LOOPING OPERATIONS
LOOPING
A loop is any area of a CD that you choose to repeat with no breaks.
LOOP IN
The “LOOP IN” point is where you wish for the loop to start. You
will notice the “LOOP IN” button will be lit every time you put in a
new CD. This is because the initial “CUE” point of the CD is also the
default “LOOP IN” and “STUTTER” point. If you wish to set a new
“LOOP IN” point, just press
while the CD is playing when it
button will light indicating a
button and in the display will
reaches the desired point. The
new loop is set. The
also illuminate indicating a point has been set and is accessible for
“STUTTER”. By default the “LOOP IN” also becomes the “STUTTER”
point.
NOTE: The CD Player will always remember a new set point as the “LOOP IN” or
“STUTTER” point until you actually set a new “LOOP IN” point or put in a new CD.
The new point will be accessible until you remove the CD from the unit. If you
change tracks and you previously set a “LOOP IN” on another track, pressing
will jump to that point.
LOOP OUT
The “LOOP OUT” determines the end point for a loop. The first time you press
while a CD is in play mode, the
“LOOP OUT” LED will turn on and flash while the song automatically returns to the “LOOP IN” point with no breaks and
continues to play. When the song reaches the “LOOP OUT” point again it returns to the “LOOP IN” point and
continues to repeat this action. You will notice the “LOOP IN” LED will also be flashing during loop action. To release
or end the LOOP press
a second time and play will continue forward when the song passes the previously set
“LOOP OUT” point. The “LOOP OUT” LED will be lit solid indicating that the “LOOP” is now in memory for “RELOOP”
purposes.
Note: The “LOOP OUT” point will be erased if “LOOP IN” is pressed or a new
“CUE” point is set after the “LOOP OUT” point. This is important because without
this point “RELOOP” will not be possible.
- The Leader in DJ Technology
©2002 Numark Industries
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
MOVING LOOP IN POINT
The “LOOP IN” point can be moved while the music is playing just by pressing
next time “LOOP OUT” is reached the CD will return to this new “LOOP IN” point.
at the new desired point. The
If
is pressed after the “LOOP OUT” point it will clear the “LOOP OUT” point.
The “LOOP IN” point can also be edited while paused. Rotate the wheel to search for a new cue point and then press
to set the new point. Check your point by pressing , then backtrack to get back to the beginning of the
track.
MOVING LOOP OUT POINT
The “LOOP OUT” point can also be moved while a loop is playing. Press
and pressing it again at the new desired point.
to release the old “LOOP OUT” point
- The Leader in DJ Technology
©2002 Numark Industries
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
RELOOP/STUTTER
RELOOP
This button performs 2 different functions depending on loop setting.
This is only possible if “LOOP” points have been previously set and the CD is playing beyond the “LOOP OUT” point.
The “RELOOP” function automatically returns the music to the “LOOP IN” point and will play the loop until it is
released with the “LOOP OUT” button.
STUTTER
This starts instant play or replay from your last set cue point or “stutter” point. Simply set your stutter point by follow
the directions for setting “Loop in” because the points are the same. Remember the button serves also for the
reloop function so if a loop out has been set the unit will also loop until released. If you set a loop in point
on a track, then return to a point previous to it by using the track function you will be able to stutter on the beginning
of the track until you pass the loop in point. Then you will be able to stutter on the previously set point.
- The Leader in DJ Technology
©2002 Numark Industries
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
USING THE BPM DISPLAY FEATURE
Press the BPM button to select the BPM feature on the display on the side of the
CD player that you wish to set.
Tap the Counter button to the beat of the music.
You will see the BPM number appear in the display. The more times you tap the more accurate your
number will be. When you adjust the pitch slider the display number will change by an equal
percentage.
- The Leader in DJ Technology
©2002 Numark Industries
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
MATCHING THE BEATS PER MINUTE (BPM)
Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear or using the manual BPM counter
and adjusting the pitch. When the tempo of the music of the selected CD player is slow compared to the tempo of the
other player, move the slider to the “+” side and match the tempo. When faster, move the pitch slider to the “-“ side.
The following description is for the case of matching the pitch of PLAYER 2 to the pitch of the music being played on
PLAYER 1.
Press PLAY/PAUSE to start PLAYER 1
PLAYER 1 is playing
Press PLAY/PAUSE to start PLAYER 2
Both CD players are playing discs.
Listen to PLAYER 2 in your headphones
When PLAYER 2 is slow
compared to PLAYER 1
speed up PLAYER 2
When PLAYER 2 is fast
compared to PLAYER 1
slow down PLAYER 2
MATCHING BEATS USING PITCH BEND
If you find the BPM’s (Beats Per Minute or Tempos) are the same, however, the drumbeats are not matched you will
need to temporarily change the pitch. This description is for the case of matching the beat of PLAYER 2 to the beat of
the music being played on PLAYER 1. (This procedure can be done on either PLAYER).
After matching the BPM’s adjust the pitch temporarily as follows:
When PLAYER 2 is behind rotate the jog wheel
When PLAYER 2 is ahead rotate the jog wheel counter
clockwise or press
to bend pitch faster
clockwise or press
to bend pitch slower.
or
or
The pitch changes automatically while the jog wheel is rotated or buttons are pressed. The faster you rotate the
wheel or longer you press the buttons, the more you change. Releasing the wheel and buttons results in a return to
the original pitch and BPM.
- The Leader in DJ Technology
©2002 Numark Industries
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
EXAMPLE OF MIXING USING TWO CD PLAYERS
While playing a disc on PLAYER 1 load a disc into PLAYER 2 and select your next track, match its pitch to
the track playing on PLAYER1 and when you are ready use the crossfader on your mixer to fade from
PLAYER 1 to PLAYER 2.
PLAYER 1
PLAYER 1
PLAYER 1
Load a disc in PLAYER 1
and select the track and
press PLAY.
Load a disc and press the
OPEN/CLOSE button.
Press the PLAY button
Select the track to be
played.
PLAYER 2
PLAYER 2
PLAYER 2
Load a disc in PLAYER 2
and select the track then
play.
Load a disc and press the
OPEN/CLOSE button.
Press the PLAY button
Select the track to be
played.
PLAYER 2
PLAYER 2
PLAYER 2
Set and edit a start cue
point on PLAYER 2
Press the Pause button of
PLAYER 2.
Press search to release.
Slowly set the right cue
point using the jog wheel.
Press search and rotate
wheel to rapidly look for a
cue point.
PLAYER 2
PLAYER 2
PLAYER 2
Check you new cue point
Listen with the monitor
and press the play button.
Set the player to the Cue
point by pressing Cue
Press the cue button then
play to be sure of the set
cue point.
PLAYER 2
MIXER
PLAYER 2
Do a MIX!
When you are happy with
you mix adjust you mixer
accordingly.
With a matching downbeat
from Player 1 press the
play button.
If you are beat mixing
turn on your Pitch adjust
and follow the directions
for beat matching.
- The Leader in DJ Technology
©2002 Numark Industries
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
BEFORE SWITCHING OFF THE POWER
When you have finished using the CD player, be sure that the disc tray is closed with the “OPEN/CLOSE” button before
switching off the power.
DO NOT switch off the power when
Switch off the power after the
disc holder has been closed
with the “OPEN/CLOSE” button
the disc holder is open.
TROUBLESHOOTING
Symptom
Possible Cause
Corrective Action
The power fails to switch on when Poor power plug connection at the Insert the power plug firmly into
the POWER switch is set to on
AC outlet or IEC Power cord loose the AC outlet and make sure
from rear of unit
connection is good in unit rear
Disc play does not start
The disc is loaded upside down
The disc is too dirty
Reload the disc with the label side
up
Clean the disc
No sound
Sound skips
Hum
Improper output cable
connections
Connect the output cables
correctly
Improper amplifier operation
Check amplifier setup
The CD player is subject to
vibrations or physical shock
Change the installation location
The disc is too dirty
Clean the disc
Loose cable connections
Firmly connect all audio plugs
- The Leader in DJ Technology
©2002 Numark Industries
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CDN 36
SPECIFICATIONS
TECHNICAL
Disc Type
Standard Compact discs (12 cm & 8 cm)
Time Display
Quantization
Track Elapsed, Track Remain, or Total remain
1 bit linear/Channel, 3 Beam Laser
Oversampling rate
Sampling Frequency
Frequency response
T.H.D. + NOISE
S/N ratio (IHF-A)
Channel separation
Output level
Short Access Time
Long Access Time
Start Time
8 Times
44.1 kHz
20 Hz to 20 kHz
Less Than 0.01%
> 90 dB
> 90 dB
2 Volts R.M.S.
< 1.5 seconds
< 3 seconds
within 0.03 seconds
Pitch control range
+/- 8 and 16%
Pitch bend
Digital Output
+/-16%
type 2, form 1, S/PDIF (Sony/Phillips Digital Interface Format)
GENERAL
Dimensions:
Controller (mm): 482 X 132 X 38
Main Unit: 482 X 88.5 X 257
Weight:
Controller: 2.3 Kg
Main Unit 4.9 Kg
Power Supply:
115/230V AC, 50/60Hz
24W
Power Consumption:
- The Leader in DJ Technology
©2000 Numark Industries
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Professional Disc Jockey Products
LIMITED PRODUCT WARRANTY
1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ Mixers, Amplifiers, CD
players, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, and all other accessories are free from defects in material and
workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the
following period of time after that date for (1) Year.
2. What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification
of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally
exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment,
or service of the mixers; (e) crossfaders.
3. What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the
purchaser, any defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return
authorization number ("RA#"). Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales
receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and
assistance on where to return the mixer, contact NUMARK customer service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective
products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a
product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on
the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property of NUMARK. If NUMARK
determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of such
mixer.
4. What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES
COVERING NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK
SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO
PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK
MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS
AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED
WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL
ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH
PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the
limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications
to this Limited Warranty, or make additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation,
whether oral or written, do not constitute warranties by NUMARK and should not be relied upon.
5. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.
6. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.
RETURN INFORMATION
•
•
•
•
A Return Authorization number must be obtained from Numark through the address or phone numbers below.
A copy of the original sales receipt must also be included for the equipment to be repaired under warranty.
The faulty equipment must be packed in its original packaging.
One additional outer layer of packaging must be included to ensure product safety. Failures to do so may inadequately protect the equipment in transit
and, therefore, jeopardize the customer’s warranty.
•
•
Numark will not accept COD shipments and no call tags will be issued for merchandise return.
Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be
submitted in writing with merchandise returned.
•
The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and
original sales receipt enclosed to:
INDUSTRIES
Attention: Service Department
11 Helmsman Avenue
Phone: +1 (401) 295-9000
Fax:
+1 (401) 295-5200
Web:
North Kingstown, RI 02852 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|