INSTALLATION INSTRUCTIONS
HB0026
NP60000 SERIES
!
!
INTENDED FOR DOMESTIC COOKING ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGE 11.
NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
V7450 rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1.
SELECT BLOWER OPTION AND INSTALL DUCTWORK............................................................................6
MEASURE INSTALLATION...................................................................................................................7
PREPARE THE INSTALLATION .............................................................................................................7
INSTALL BACKSPLASH ......................................................................................................................8
INSTALL WOOD MOUNTING STRIP .....................................................................................................8
INSTALL THE HOOD .........................................................................................................................8
SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)............................................................................8
INSTALL TRANSITION TO ROUGH-IN PLATE..........................................................................................8
INSTALL THE ROUGH-IN PLATE TO THE HOOD.....................................................................................9
CONNECT THE WIRING ....................................................................................................................9
INSTALL THE OPTIONAL SOFFIT CHIMNEY ..........................................................................................9
INSTALL THE BLOWER ......................................................................................................................9
INSTALL LIGHT BULBS AND WARMING LAMPS .....................................................................................10
INSTALL FILTERS .............................................................................................................................10
USE AND CARE ..............................................................................................................................11
OPERATION ....................................................................................................................................11
SERVICE PARTS..............................................................................................................................12
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
WARRANTY
NUTONE ONE-YEAR LIMITED WARRANTY
NuTone warrants to the original consumer purchaser of its products that such products will be free from defects
in materials or workmanship for a period of one year from the date of original purchase.THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, NuTone will, at its option, repair or replace, without charge, any product or part which
is found to be defective under normal use and service.
This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been
subject to misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty
installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty.
Some states or provinces do not allow limitation on how long an implied warranty lasts, so the above limitation
may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN
CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states or provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state
or province to another. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify NuTone at the address or telephone number below,
(b) give the model number and part identification and (c) describe the nature of any defect in the product or part.
At the time of requesting warranty service, you must present evidence of the original purchase date.
NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- NP60000 SERIES RANGE HOOD SYSTEM -
INTERIOR BLOWERS
Model 441
Model 647
Model 634 or 644
(roof cap)
Model 437
(10’’ round wall cap)
(7” round wall cap)
(High capacity roof cap)
Model 418
(10” round adjustable elbow)
Model 415
(7” round adjustable elbow)
Model 410
(10” round duct—2 ft. sections)
Model 407
(7” round duct—2 ft. sections)
Model 427
(4 1/2” x 18 1/
to 10” round,
Model 423
Model 424
Model 454
(4 1/2” x 18 1/
Model 453
(4 1/2” x 18 1/
to 10” round -
horiz. /left
2”
(4 1/2” x 18 1/2” to (4 1/2” x 18 1/2” to
2”
2”
10” round - vertical 10” round - horiz. to 10” round -
front/rear horiz. /right
6” high - lateral
OPTIONAL
SOFFIT CHIMNEY
RMN SERIES
MODEL RM326H
BLOWER/ROUGH-IN KIT
(1200 cfm interior blower
& rough-in plate)
MODEL RM325H
BLOWER/ROUGH-IN KIT
(600 cfm interior blower &
rough-in plate)
NP60000
SERIES HOOD
(Canopy with
blower controls
& lighting.
Required for all
installations.)
OPTIONAL
BAFFLE FILTERS
RBF SERIES
RMP SERIES BACKSPLASH
(Stainless steel wall covering
with warming shelves. Optional)
HL0075
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- NP60000 SERIES RANGE HOOD SYSTEM -
IN-LINE AND EXTERIOR BLOWERS
Model 441
Model 437
Model HLB9 (800 cfm)
(10” round wall cap)
(High capacity roof cap)
Model 335 (1200 cfm)
or 336 (1500 cfm)
exterior blower
or HLB11 (1100 cfm)
in-line blower
Model 331H (600 cfm)
or 332H (900 cfm)
exterior blower
(includes two 8” x 12” to
10’’ round transitions)
Model 441
(10” Round
wall cap)
Model HLB6 (600 cfm)
in-line blower
(includes two 4 ½” x 18 ½”
to 10’’ round transitions)
Model 421
Model 418
(10” round vert.
in-line damper)
Recommended
for use with
10” round
adjustable elbow
(optional)
Model HLB3 (280 cfm)
in-line blower
exterior blowers
(includes one 8” to 10”
round transition)
Model 410
(10” round duct
—2ft. sections)
OPTIONAL
SOFFIT CHIMNEY
RMN SERIES
NP60000
SERIES HOOD
(Canopy with
blower controls
& lighting.
required for all
installations.)
332KR in-line and exterior blower
rough-in kit - Purchase separately.
OPTIONAL
BAFFLE FILTERS
RBF SERIES
RMP SERIES
BACKSPLASH
(Stainless steel wall
covering with warming
shelves. Optional.)
HL0076
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK
Either an interior or exterior blower or in-line blower may be used with this hood. The NuTone Premier 60000 Series must
be installed with blower models RM325H, RM326H, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only.
Other blowers cannot be substituted. (Blowers sold separately).
NOTE: In addition to the blower models listed above, this hood is also compatible with older internal versions 325H
and 326H. However, discard the installation instructions included with those blowers and contact our technical
support to obtain replacement instruction.
Plan where and how the ductwork will be installed.
If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 6, 9, 10, 11,
13 and up of this manual.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use 2” duct tape to
seal duct joints.
ROOF CAP
ROOF CAP
7" (178 mm)
ROUND DUCT
10" (254 mm)
ROUND DUCT
DECORATIVE
FLUE
12"
(305 mm)
WALL CAP
WALL CAP
DECORATIVE
12"
(305 mm)
or SOFFIT
FLUE
or SOFFIT
HOOD
4-1/2" x 18-1/2"
to 10"
(114 x 470 to
254 mm) ROUND
TRANSITION
(see page 4)
7" (178 mm)
ROUND
ELBOW
HOOD
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
HH0025A
HH0024A
MODEL RM325H SINGLE BLOWER
TYPICAL DUCTWORK
MODEL RM326H DUAL BLOWER
TYPICAL DUCTWORK
EXTERIOR BLOWER
Roof cap
10" (254 mm)
ROUND DUCT
10” round duct
In-line blower
DECORATIVE
10" (254 mm)
ROUND ELBOW
12"
FLUE
or SOFFIT
(305 mm)
Wall
cap
EXTERIOR
BLOWER
HOOD
332KR
Hood
ROUGH-IN KIT
(see page 5)
24” minimum
above cooking
surface
24" TO 30" (609 to 762 mm)
ABOVE COOKING SURFACE
HH0026A
HH0066A
MODEL 331H, 332H, 335 OR 336
EXTERIOR BLOWER TYPICAL DUCTWORK
MODEL HLB3, HLB6, HLB9 OR HLB11
IN-LINE BLOWER TYPICAL DUCTWORK
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. MEASURE INSTALLATION
Dimensions for the most common installation are shown below.
The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is
highly recommended for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
Standard
8 ft. (2.44 m)
ceiling
S
t
a
nd
457 mm
ve oo
ca
a
r
d
18
"
18"
(
)
H
(457 mm)
o
r
-
c
k
e
t
op
19"
(483 mm)
b
i
n
t
Top of wood
mounting strip
Hood
RMP Series
Backsplash
(optional)
24"
(610 mm)
Standard 36"
(914 mm)
Cooktop
H cooktop
HH0028A
INSTALLATION WITH STANDARD 18’’
HIGH OVER-COOKTOP CABINET
INSTALLATION WITH STANDARD
12’’ SOFFIT OR OPTIONAL
SOFFIT CHIMNEY RMN SERIES
3. PREPARE THE INSTALLATION
Remove the installation kit from inside the hood.
Make sure that the following items are included:
- Wood strip
- Installation manual
- Accessories including:
• Filters (Quantity varies depending on range hood width)
• Bag of parts including:
(4) flat head screws #10-2’’, (8) screws #8 x 3⁄4’’, (4) nuts #10-32, (2) wall anchors, (2) washers 3⁄16’’ ID x 3⁄4’’ OD
Parts sold separately:
- Interior blower Model RM325H or RM326H (both include rough-in kit)
- In-line blower assembly HLB3, HLB6, HLB9 or HLB11 (all include transition)
- In-line and exterior blower rough-in plate model 332KR, required for all In-line or Exterior Blowers
- Exterior blower assembly 331H, 332H, 335 or 336
- Halogen lights (120 V, 50 W, PAR 20)
- Heat lamps (Infrared, 120 V, BR40, 250 W max.)
- RMP Series Backsplash (optional)
- RBF Series Baffle filters (optional)
- Transitions, duct, elbows, dampers, wall and roof caps.
Refer to pages 4 and 5 for a complete list of venting options
4
2
3
1
and model numbers.
Using a Phillips #2 or a Robertson #2 screwdriver, unscrew the
hood from the bottom of crate. Refer to figure beside to locate all
4 screws. Discard these screws and remove hood from wood pallet.
HR0002
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALL BACKSPLASH (OPTIONAL)
(Optional) RMP Series
Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting
screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance between bottom of
hood and range control panel or cooktop. (See instructions packed with backsplash.)
5. INSTALL WOOD MOUNTING STRIP
Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustration below and
under step 2). Use #10 - 2’’ flat head screws to secure the mounting strip to the drywall. Make sure to hit the wall studs.
CAUTION
Due to the weight of this hood, ensure that the wood strip
is attached to all of the available studs (2 studs minimum
for a 30’’ hood, more as wood width increases); not into
(see page 7)
the drywall alone.
1. Drywall
2. Wood mounting strip
3. Flat head screw
4. Wall anchor location
5. Back of hood outline
6. Wall studs
6. INSTALL THE HOOD
Rest the back cavity of the hood on the wood mounting strip.
TOP OF HOOD (INSIDE VIEW)
CAUTION
Hold the hood until it is completely secured to the wood
mounting strip.
MOUNTING SCREWS LOCATION
Secure the hood to wood mounting strip with (4) screws #8 x 3⁄4’’ (for 30’’
and 36’’ width hoods) or (6) screws (for 42’’ width and wider hoods)
provided at locations shown. Drill (2) ⁄16’’ size holes into the drywall for
wall anchors through the existing holes in the inside hood back in the
locations shown. Then, install the two wall anchors with the remaining
#8 x 3⁄4’’ screws and the (2) washers provided.
BACK OF HOOD (INSIDE VIEW)
WALL ANCHORS LOCATION
3
HD0064
7. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)
INTERIOR BLOWER: Follow all subsequent steps of this manual.
EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 9 and up of the present manual.
8. INSTALL TRANSITION TO ROUGH-IN PLATE (INTERIOR BLOWER ONLY)
Model 423, 424, 427 453, or 454
Attach transition (if required) to blower rough-in plate.
Use duct tape to make all joints secure and air-tight.
NOTE: Model RM325H blower plate connects directly to 7’’ round
ductwork without a transition.
HD0049
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
9. INSTALL THE ROUGH-IN PLATE TO THE HOOD (ALL BLOWERS)
Run power cable to installation location. Refer to the instructions included
with the selected blower or rough-in kit (sold separately) for details on
installing the rough-in plate. Install the rough-in plate so that the wiring
2
1
1
1
4
box is located on the right side as you are facing the hood.
For ducting through back of hood, remove existing plate from inside
back of hood and attach it to inside top of hood to cover hole. Secure to
3
threaded studs with same (4) nuts.
1
For ducting through top of hood, existing plate remains in place on
inside back of hood.
HD0063
1. Locknuts
3. Rough-in plate on back of hood
2. Plate on top of hood 4. Wiring cover
Connect ducting to transition or rough-in plate as you are installing the
rough-in plate. Use duct tape to make all joints secure and air-tight.
10. CONNECT THE WIRING (ALL BLOWERS)
WARNING
!
Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with
all applicable codes and standards. Before connecting wires, switch power off at service panel and
lock service disconnecting means to prevent power to be switched on accidentally.
Remove wiring cover from rough-in plate and set aside.
Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw.
Reinstall wiring cover.
11. INSTALL THE OPTIONAL SOFFIT CHIMNEY
(OPTIONAL) RMN Series
Refer to the instructions included with the soffit chimney.
12. INSTALL THE BLOWER (INTERIOR OR EXTERIOR BLOWER)
Refer to instructions included with blower.
Once the blower is installed, plug the power supply to the 3-prong male
connector (A) and the blower unit into the 2-prong female receptacle (B)
A
B
inside the hood.
WARNING
!
Never plug the 2-prong blower cord to the 3-prong power
supply cord.
HE0003
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
13. INSTALL LIGHT BULBS AND WARMING LAMPS
Install (2) heat lamp bulbs. Use BR40 size, 250 W max., infrared bulbs only (sold separately).
Install (3) halogen light bulbs. Use PAR20 size, 50 W (sold separately).
14. INSTALL FILTERS
CAUTION
Remove protective plastic film covering filters before installing them.
It is recommended to install side filters first and finish with center one(s).
1.
2.
3.
4.
Insert upper end of filter into the hood (finger sized cup side).
Raise lower end toward the inside of hood.
Position lower end of filter into channel and pull.
Using finger sized cup, pull on the upper end of filter and slide it under the front inner retaining piece.
1
2
4
HD0065
3
HD0024
Replacement filters are available from your dealer. See label inside hood for size and part number.
Baffle Filters
Baffle filters are available as an option. To order them, refer to the table below to find the appropriate filter kit number
to your hood. To install them, refer to instruction sheet included with baffle filter kit.
KIT #
HOOD WIDTH
30”
RBF6030
RBF6036
RBF6042
RBF6048
RBF6054
RBF6060
RBF6066
RBF6072
36”
42”
48”
54”
60”
66”
72”
HD0011
BAFFLE FILTER (TYPICAL)
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
15. USE AND CARE
16. OPERATION
Grease Filters
Always turn ON your hood before you begin cooking in
order to establish an air flow in the kitchen. Let the blower run
for a few minutes to clear the air after you turn off the range.
This will help keep the whole kitchen cleaner and brighter.
The grease filters should be cleaned frequently. Use a
warm detergent solution. Grease filters are dishwasher
safe. Wash more often if your cooking style generates
greater grease—like frying foods or wok cooking.
Remove filters by pushing filters towards the back of hood
and rotating filters downward.
4
6
5
Blower Cleaning
3
2
3
3
1
1
Remove the filters in order to access the blower. Vacuum
blower to clean. Do not immerse in water. Refer to blower
instruction manual for more details.
HC0004
1. Warming lamps
2. Warming lamp switches
3. Halogen lights
4. Halogen light switches
5. ON/OFF Blower switch
6. Blower speed control
Grease Rail
The grease rail should be cleaned frequently, especially if
baffle filters are used.
Remove filters, then, disassemble the grease rail from the hood
by removing its 3 retaining screws. See illustration below.
Warming lamps (Infrared)
Each warming lamp (item 1 in picture above) is controlled
with is own ON/OFF switch (item 2 on picture above).
Use only BR40 Size, 250 W max., Infrared bulbs (purchase
separately).
WARNING
!
Never place highly flammable material under
warming lamps.
Cooktop Lighting (Halogen)
A double set of ON/OFF switches (item 4 on picture above)
control the halogen lights (item 3 on picture above).
The front rocker controls the center light. The rear rocker
controls both side lights. Select one, two, or three lights for
best cooktop lighting.
HD0069
Refer to Stainless steel cleaning in Hood Cleaning section
below. Once the grease rail is clean and dry, reassemble it
to the hood and reinstall filters.
Hood Cleaning
Stainless steel cleaning: How to maintain its “BRIGHT LOOK”
Use PAR 20, 50 W halogen bulbs (purchase separately).
Blower
Do:
The blower is operated using two (2) controls.
• Regularly wash with clean cloth or rag soaked with
warm water and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after
cleaning. Wipe dry completely.
Use the red, lighted ON/OFF switch (item 5 on picture
above) to start and stop the blower. When turned on, the
blower will operate at the previous setting of the speed
control (item 6 on picture above).
Turn the speed control knob clockwise to decrease blower
speed—counterclockwise to increase speed.
• You may also use a specialized household stainless
steel cleaner.
HEAT SENTRY™
Don’t:
This hood is equipped with a HEAT SENTRY™ thermostat.
This thermostat is a device that will turn on or speed up the
blower if it senses excessive heat above the cooking surface.
• Do not use any steel or stainless steel wool or any
other scrapers to remove stubborn dirt.
• Do not use any harsh or abrasive cleansers.
• Do not allow dirt to accumulate.
1) If blower is OFF—it turns blower ON to HIGH speed.
• Do not let plaster dust or any other construction
residues reach the hood. During construction/renovation,
cover the hood to make sure no dust sticks to stainless
steel surface.
2) If blower is ON at a lower speed setting—it turns the
blower up to HIGH speed.
When the temperature level drops to normal, the blower
will return to its original setting.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel.
• Any products containing: chloride, fluoride, iodide,
bromide will deteriorate surfaces rapidly.
• Any combustible products used for cleaning such as
acetone, alcohol, ether, benzol, etc., are highly explosive
and should never be used close to a range.
Enamel finish:
WARNING
!
TM
The HEAT SENTRY can start the blower even if
the hood is turned OFF. In this case, it is impossible
to turn the blower OFF with blower switch. If you
must stop the blower, do it from the main
electrical panel.
Clean with warm water and mild detergent only.
When discoloration occcurs, use a good enamel polish
such as automotive polish. (DO NOT use rough abrasive
cleaner or porcelain cleaner.)
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
17. SERVICE PARTS
19
20
18
16
17
10
13
21
15
19
2
11
12
3
5
4
7
14
6
6
9
1
8
1
HL0031
KEY
PART
QTY (HOOD WIDTH)
NO. NUMBER DESCRIPTION
30’’ 36’’ 42’’ 48’’ 54’’ 60’’ 66’’ 72’’
1
2
3
4
5
6
7
8
9
V02264
V02773
V02772
V03435
V03436
SOCKET LAMP
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
3
-
-
-
1
-
-
-
-
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
3
-
-
-
1
-
-
-
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
-
3
-
-
-
1
-
-
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
4
-
-
-
-
-
1
-
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
-
-
3
-
-
-
-
1
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
5
-
-
-
-
-
-
-
1
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
2
3
-
-
-
-
-
-
-
5
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
-
-
-
4
-
-
-
-
-
-
MALE CONNECTOR
FEMALE CONNECTOR
THERMOSTAT
THERMOSTAT BRACKET
V02563 SPST SINGLE SWITCH FOR WARMING LAMPS
SPST DOUBLE SWITCH FOR HALOGEN LAMP
V03503 SPST LIGHTED SINGLE SWITCH FOR BLOWER
V03502
V03504
SPEED CONTROL BUTTON
SPEED CONTROLLER
TERMINAL STRIP
10 V03501
11 V03505
§
§
§
V03517 10’’ POWER CORD
V03519 10’’ CONTROL WIRE
V03520 10’’ LIGHTED SWITCH WIRE
12 V00673 LOCK-NUT 8-32
13 V02512 SCREW 8-32 X ⁄2 QUADREX
1
1
14 V01869 MACHINE SCREW 8-32 X ⁄4
15 V01582 LOCK NUT 6-32
SQUARE PERF. GRILLE FILTER 9.5” X 15.25” X 0.355”
SQUARE PERF. GRILLE FILTER 11.61” X 15.25” X 0.355”
SQUARE PERF. GRILLE FILTER 13.61” X 15.25” X 0.355”
SQUARE PERF. GRILLE FILTER 17.525” X 15.25” X 0.355”
GREASE RAIL 30’’
GREASE RAIL 36’’
GREASE RAIL 42’’
16 V05522
17 V14766
GREASE RAIL 48’’
GREASE RAIL 54’’
GREASE RAIL 60’’
GREASE RAIL 66’’
GREASE RAIL 72’’
1
-
-
-
-
-
-
-
-
1
4
2
1
1
1
18 V05528 FILTER SPRING 5.265’’ X 0.350’’
19 V05521 SEALING EXTRUSION 20.625’’
3
2
1
1
1
3
2
1
1
1
3
2
1
1
1
4
2
1
1
1
3
2
1
1
1
5
2
1
1
1
5
2
1
1
1
20 V14744
21 V14745
LEFT SIDE LINER
RIGHT SIDE LINER
INSTALLATION GUIDE
§
V05527
PARTS BAG (FLAT HEAD SCREW #10 X 2’’ (4),
3
§
V12971 SCREWS #8 X ⁄4’’ (8), NUTS #10-32 (4),
1
1
1
1
1
1
1
1
3
3
WALL ANCHORS (2), WASHERS ⁄16’’ ID X ⁄4’’ OD)
§
§*
V02544 HALOGEN LAMP PAR 20, 50 W
WARMING LAMP BR40, 250 W MAX.
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
§
*
NOT SHOWN.
PURCHASE LOCALLY
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|