MODELS 741BRNT • 741SNNT • 741WHNT • 741BRFLNT • 741WHFLNT
Page 1
DECORATIVE SERIES
CEILING VENTILATORS
READ AND SAVE THESE INSTRUCTIONS
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
7. NEVER place a switch where it can be reached from a tub or
shower.
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
8. Fluorescent models only: Do not use a dimmer switch to con-
trol the light of this unit.
9. This unit must be grounded.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a quali-
fied person(s) in accordance with all applicable codes and stan-
dards, including fire-rated construction codes and standards.
10. This unit is U.L. listed. Type I.C. inherently protected.
!
CAUTION
1. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials and vapors.
2. This product is designed for ceiling installation only. This prod-
uct is designed for installation in ceilings up to a 12/12 pitch.
Ductwork must point up. DO NOT MOUNT THIS PRODUCT IN
A WALL.
3. The light fixture assembly must be mounted to the fan housing
assembly included with this product. Do not mount the light
fixture assembly to a wiring outlet box.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent backdrafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and theAmerican Society for Heating, Refrigeration andAir Con-
ditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage elec-
trical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
4. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
5. Please read specification label on product for further informa-
tion and requirements.
TYPICAL INSTALLATIONS
TYPICAL INSTALLATIONS
4" ROUND
DUCT
POWER CABLE
POWER CABLE
MOUNTING TABS
MOUNTING TABS
CEILING
JOIST
HOUSING
HOUSING
GRILLE
PAN
CEILING
MATERIAL
ADDITIONAL
FRAMING
CEILING
MATERIAL
GLASS
LIGHT SHADE
CEILING
JOIST
GRILLE
PAN
GLASS
LIGHT SHADE
16”-ON-CENTER CEILING JOISTS
Housing mounted directly to joist.
24”-ON-CENTER CEILING JOISTS
Housing mounted to additional framing.
Installer: Leave this manual with the homeowner.
Homeowner: Use and Care information on page 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS 741BRNT • 741SNNT • 741WHNT • 741BRFLNT • 741WHFLNT
Page 3
INSTALL THE HOUSING
(continued)
CONNECT THE WIRING
SCHEMATIC WIRING DIAGRAM
L I G H T
S W I T C H
R E D
B L U
W H T
L I G H T
( W H I T E )
Existing Construction
V E N T
S W I T C H
B L K
B L K
W H T
V E N T
( B L A C K )
B L K
W H T
G R D
L I N E
I N
W H T
G R D
S W I T C H B O X
U N I T
WHITE
RECEPTACLE
(LIGHT)
BLACK
WHITE
BLUE
RED
GROUND
(bare)
BLACK
RECEPTACLE
(FAN)
DUAL CONTROL
(purchase separately)
SWITCH BOX
4. Place housing in opening so that its bottom edge is flush
with finished ceiling. Nail to joist through keyhole on both
sides. To ensure a noise-free installation, drive another
nail through the top hole of each mounting bracket.
LIGHT
FAN
WIRING
PLATE
1. Wire unit following diagram
ADDITIONAL
MOUNTING
HOLES
above. Run electrical cable as
direct as possible to unit. Do not
allow cable to touch sides or top of
unit after installation is complete.
120 VAC
LINE IN
5. Additional mounting holes are provided for installations
where access from above is inconvenient or not possible.
Nail or screw housing directly to joists or framing.
ATTACH THE GRILLE PANAND
GLASS SHADE
1. Locate the grille pan over
INSTALL THE DUCTWORK
GRILLE
SCREW
the fan housing and con-
nect the wiring harness
plug into white receptacle
in the fan housing.
GRILLE
PAN
FLUSH
2. Insert rod through center
hole of grille pan. Use
washer between collar on
rod and pan.
WASHER
ROD
COLLAR
3. Thread rod onto grille screw in housing, until pan is tight
against ceiling.
NOTE: The duct connector
has a counter-balanced
damper flap. The flap will be
MODELS
741BRNT
741SNNT
741WHNT
MODELS
741BRFLNT
741WHFLNT
"open" approx. 1" when duct connector is attached to hous-
ing. This design permits insulation to be in direct contact with
fan/light housing per UL (Underwriters Laboratories) stan-
dards.Theslightestbackdraft,however,willclosethedamper
flap, preventing air from entering unit or finished space.
4. Install bulbs. (see "Bulb Replace-
ment" chart on next page for proper
bulbs for your model).
5. Place glass shade over mounting
rod and align shade onto grille pan.
Secure glass shade to grille pan with
finial cap and finial nut as shown.
1. Snap the damper/duct connector onto housing. Make sure
that tabs on the connector lock into slots in housing. Top
of damper/duct connector should be flush with top of hous-
ing.
2. Connect 4” round duct to damper/duct connector and ex-
tend duct to outside through a roof or wall cap. Check
damper to make sure that it opens freely. Tape all duct
connections to make them secure and air tight.
6. Restore electrical power and check operation of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS 741BRNT • 741SNNT • 741WHNT • 741BRFLNT • 741WHFLNT
Page 4
USE AND CARE
USE AND CARE
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND
LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVIC-
ING THIS UNIT.
CLEANING
TO CLEAN GLASS SHADE AND GRILLE PAN:
BULB REPLACEMENT
Remove finial nut and finial cap and remove glass shade. Shade
can be wiped clean with a mild detergent solution or glass cleaner
and dried with a soft cloth. Remove 2 bulbs. Grille pan may be
gently vacuumed and wiped clean with a soft cloth. Never use abra-
sive cloth, steel wool pads or scouring powders on glass shade or
grille pan. METAL AND ELECTRICAL PARTS SHOULD NEVER
BE IMMERSED IN WATER.
Remove finial nut and cap and remove glass shade. Replace bulb
or bulbs as required. Replace glass shade, finial cap & securely
tighten finial nut.
Models 741BRNT, 741SNNT & 741WHNT
Use 60 Watt maximum incandescent bulb.
Models 741BRFLNT & 741WHFLNT:
Use only the following 13 Watt fluorescent lamps:Broan 97010729,
Sylvania CF13DD827, Phillips PL-C 13W/27/USA, General Elec-
tric F13DBX23T4/SPX27, Osram CF13DD827, NEMA Type
CFQ13W/GX23.
TO CLEAN FAN ASSEMBLY:
Remove grille pan and unplug fan assembly (black receptacle).
Gently vacuum fan, motor and interior of housing. METAL AND
ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WA-
TER.
MOTOR LUBRICATION
The motor is permanently lubricated. Do not oil or disassemble
motor.
27
SERVICE PARTS
26
KEY PART NO.
DESCRIPTION
1
97013913 Finial Nut - Bright Brass
97015574 Finial Nut - Satin Nickel
97013914 Finial Nut - White
97013915 Finial Cap - Bright Brass
97015575 Finial Cap - Satin Nickel
97013916 Finial Cap - White
99523639 Glass Shade
8
2
13
25
12
22
C
8
3
4
5
6
7
24
23
21
99523652 Shade Mounting Rod
99523339 Washer
5
11
20
97015320 Lamp Socket (2 req.)
(741BRNT, 741SNNT, 741WHNT)
5
19
18
5
7
8
9
99523636 Hex Nut, 1/8 Jam
97015313 Wire Harness
99523640 Fluorescent Lamp Holder
(2 req.)(741BRFLNT, 741WHFLNT)
14
9
10
10
11
12
13
14
99523638 #6B-20 x 3/8” Pan Hd. Screw
(4 req.)(741BRFLNT, 741WHFLNT)
B
4
6
99160225 #8-32 x 1/2” Rd. Hd. M. Screw
(4 req.)(741BRFLNT, 741WHFLNT)
4
17
16
97015321 Ballast Transformer (2 req.)
(741BRFLNT, 741WHFLNT)
99260425 #8-32 Serrated Hex Locknut
(4 req.)(741BRFLNT, 741WHFLNT)
3
A
15
99523501 Grille/Pan (741BRNT, 741BRFLNT)
99523773 Grille/Pan (741SNNT)
99523502 Grille/Pan (741WHNT, 741WHFLNT)
99260428 Motor Nut, #6-32 Hex (2 req.)
99150618 Grille Screw
2
1
15
16
17
18
19
20
21
22
23
24
25
26
27
A
WARRANTY
97014926 Motor Plate
99080522 Motor
NUTONE ONE YEAR LIMITED WARRANTY
99110446 Blower Wheel
Nutone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or
workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULARPURPOSE.
During this one-year period, Nutone will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does not cover (a)
normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by Nutone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not
allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND
EXCLUSIVEREMEDYUNDERTHISWARRANTY.NUTONESHALLNOTBELIABLEFORINCIDENTAL,CONSEQUENTIALOR
SPECIALDAMAGESARISINGOUTOFORINCONNECTIONWITHPRODUCTUSEORPERFORMANCE. Somestatesdonot
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty
supersedes all prior warranties.
99270981 Lamp Receptacle, White
99270982 Motor Receptacle, Black
98009612 Wiring Panel
99150471 Ground Screw
99170245 Screw, #8-18 x 3/8”
98008868 Wiring Plate
97014185 Damper/Duct Connector
97014922 Housing Assembly
99523699 Light Fixture Assembly (741BRNT)
(Includes Key Nos. 1 thru 14)
99523770 Light Fixture Assembly (741SNNT)
99523700 Light Fixture Assembly (741WHNT)
99523701 Light Fixture Assembly (741BRFLNT)
99523702 Light Fixture Assembly (741WHFLNT)
97015312 Blower Assembly
(Includes Key Nos. 15 thru 19)
97015171 Wire Panel Assembly
(Includes Key Nos. 20, 21, 22)
To qualify for warranty service, you must (a) notify Nutone at the address stated below or telephone: 1-800-543-8687, (b) give the
modelnumberandpartidentificationand(c)describethenatureofanydefectintheproductorpart.Atthetimeofrequestingwarranty
service, you must present evidence of the original purchase date.
B
C
NuTone, Inc. Madison and Red Bank Roads, Cincinnati, Ohio 45227 (1-888-336-6151)
99042913D
Order replacement parts by “PART NO.” - not by “KEY NO.”
Download from Www.Somanuals.com. All Manuals Search And Download.
|