North Star Portable Generator M165957K User Manual

M165957K

ITEM NUMBER: 165957

SERIAL NUMBER: _____________

Owner’s Manual

Instructions for Installation/Set-up, Operation, Servicing, & Storage

Portable, Outdoor Use-Only, Gasoline Generator

6600 Watt Continuous (8000 Watt Surge) Capacity

Can be used to power individual appliances plugged directly into the generator’s outlets, or as a

back-up connection to a building’s power supply (via a professionally installed UL-approved

transfer switch.

WARNING

READ and UNDERSTAND this manual completely before using the generator! Failure to properly set up,

operate, and maintain this generator could result in serious injury or death from carbon monoxide poisoning,

electric shock, fire/explosion, or burns. In particular, be aware of the following hazards:

CO Poisoning

Generators give off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it.

• ONLY run generator OUTDOORS and AWAY from building air intakes. NEVER run generator inside any enclosed or

semi-enclosed spaces, including homes, basements, garages, sheds, boxes, RVs, boats or pick-up truck beds. These

spaces can trap poisonous gases, EVEN if you run a fan or open windows.

• Install carbon monoxide alarms inside nearby structures/buildings (battery-operated, or plug-in with battery backup).

Electric shock / Electrocution

• High voltage electricity from generator can kill. DO NOT operate in wet locations. Be sure generator is properly

grounded. Use only UL-listed, outdoor-rated grounded extension cords of proper size.

• NEVER plug the generator directly into a wall outlet. ANY connection to a building’s electrical system MUST

ISOLATE THE GENERATOR FROM UTILITY POWER via a UL-approved transfer switch installed by a licensed

electrician. Otherwise, back feed from the generator into the power grid could kill utility workers.

Fire / Explosion

• DO NOT overload generator (per rated capacity), and OPERATE ONLY in an area with adequate cooling ventilation so

engine does not overheat. Exhaust can be extremely hot. Keep muffler at least 7’ from all combustible objects.

• All fuels are flammable. Never fuel a running or hot engine. Never pump fuel directly into generator at gas station – use

approved container to transfer fuel. Ensure there are no fuel leaks, and keep sources of sparks and flames away.

• ALWAYS keep a fire extinguisher rated “ABC” nearby.

STOP!

CHOOSE THE RIGHT GENERATOR FOR YOUR NEEDS. See the “Power load Planning & Management” section

of this manual to determine your power load requirements and then compare to the generator’s rated capacity.

INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged. See the “Unpacking

& Delivery Inspection” section for instructions on whom to contact to report missing or damaged parts.

ARRANGE FOR PROFESSIONAL INSTALLATION of a transfer switch if you will be connecting the generator to

your building’s electrical system. See the “Installation/Initial Set-Up” section for more information about this

requirement.

Any Questions, Comments, Problems, or Parts Orders

Call NorthStar Product Support 1-800-270-0810

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Hazard Signal Word Definitions ..................................................................................................2

About Your Generator ..................................................................................................................4

Specifications ..................................................................................................................................6

Safety Label Locations...................................................................................................................7

Machine Component Identification..............................................................................................8

Power Load Planning & Management.........................................................................................10

Installation / Initial Set-Up:

1. Unpacking & Delivery Inspection..........................................................................................12

2. Planning the Power Load........................................................................................................12

3. Set-up as a PORTABLE or BUILDING BACK-UP Power Source ......................................13

4. Selecting a Suitable Site .........................................................................................................16

5. Grounding the Generator........................................................................................................18

6. Battery Installation .................................................................................................................19

Operation:

1. General Safety Rules for Operation .......................................................................................20

2. Preparing for Operation..........................................................................................................23

3. Starting the Engine .................................................................................................................26

4. Checking Generator Output....................................................................................................27

5. Connecting Loads...................................................................................................................28

6. Stopping the Engine ...............................................................................................................28

7. Storage & Exercise.................................................................................................................29

Maintenance & Repair..................................................................................................................31

Troubleshooting.............................................................................................................................33

Summary of Important Safety Information for Operation.......................................................34

Generator Exploded View ............................................................................................................38

Wiring Diagram.............................................................................................................................40

Generator Head Exploded View ..................................................................................................41

Download from Www.Somanuals.com. All Manuals Search And Download.

About Your Generator

Thank you for purchasing your NorthStar portable generator!

About Your Generator

This engine-driven, portable generator is designed to provide up to 8000 Watts of

electrical power (6600 watts continuous, 8000 watts surge). It can supply power:

1. As a portable power source. You can plug appliances directly into the generator’s

electrical outlets.

2. As a back-up, standby power source for a building. A licensed electrician can connect

the generator to your building’s electrical system via the installation of an UL-approved

transfer switch. (See the “Installation & Initial Set-up” section of this manual to learn

more about specific requirements and precautions relating to wiring the generator to your

building’s electrical system.)

You must select a generator adequately sized for your power needs. You need to

determine the power needs of all the appliances/tools you wish to power at the same time and

choose a generator rated to provide at least that power level. See the “Power Load Planning &

Management” section of this manual to determine your specific power load requirements and

then compare them to this generator’s rated capacity. You must not overload the generator.

Overloading will cause damage to the generator and attached electrical devices, and may also

result in fire.

Be sure to read about site selection and grounding requirements for running this

generator. More detailed information can be found in the “Installation & Initial Set-up, Steps

5 & 6” of this manual.

This generator is too heavy for one person to lift without mechanical assistance. An

optional wheel kit is available from NorthStar and is recommended if you will be moving the

generator unassisted. Other optional accessories available from NorthStar include a cover for

storage, UL-approved transfer switches, and extension cords.

Contact NorthStar Product Support at 1-800-270-0810 with questions about optional

accessories or to order.

Read this Manual

WARNING

Improper use or maintenance of this generator can result in serious injury or death from

carbon monoxide poisoning, electric shock/electrocution, fire/explosion, or burns.

Read this manual completely before using the generator and follow all instructions and

safety rules.

You must follow all instructions and safety precautions presented throughout this manual. A

summary of important safety information can be found at the end of the manual. Keep this

manual for reference and review.

Proper preparation, operation, and maintenance will result in operator safety, as well as best

performance and long life of the generator. For detailed engine operation and maintenance

information, always refer to the engine Owner’s Manual furnished with the generator.

Download from Www.Somanuals.com. All Manuals Search And Download.

About Your Generator (cont’d)

NorthStar is constantly improving its products. The specifications outlined herein are subject

to change without prior notice or obligation. The purchaser and/or user shall assume liability

for any modification and/or alterations of this equipment from original design and

manufacture.

Before using, the user shall determine the suitability of this product for its intended use and

assumes liability therein.

Contact NorthStar Product Support at 1-800-270-0810 for any questions about the

appropriate use of this generator.

Warranty Registration

Please fill out and submit the warranty registration card so that we have your contact

information for any future product literature or replacement parts you may need.

ATTENTION:

All Rental Companies and Private Owners who loan this

equipment to others!

All persons to whom you rent/loan this generator must have access to and read this manual.

Keep this owner’s manual with the generator at all times and advise all persons who will

operate the machine to read it. You must also provide personal instruction on how to safely

operate the generator and remain available to answer any questions a renter/borrower might

have.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications – Item #165957K

SPECIFICATIONS

Item Number

#165957

8000 Watts (W)

Maximum Output

Continuous Output

Voltage

6600 Watts (W)

120 / 240 Volt (V)

Phase

Frequency

Power Factor

Engine

Engine Speed

Fuel Type

Single phase (4-wire)

56.5-63.3 Hertz (Hz)

1.0 p.f.

13 HP Honda GX390

3390-3800 RPM

Unleaded gasoline

Fuel Capacity

Oil Capacity

Starting Method

120 V Receptacle

6.5 gallons (24.6 L)

1.16 US quarts (1.1 L)

Electric / Recoil

15 Amp (A) duplex

(NEMA 5-15R) & 20 Amp (A) duplex

(NEMA 5-20R)

120/240 V Receptacle

Circuit Breakers

30 Amp (A) locking device

(NEMA L14-30R)

30 Amp (A), Qty. 2; 20 Amp (A), Qty. 2;

15 Amp (A), Qty. 1; thermal,

push to reset style

Grounding Post

Battery (not included)

Receives 12 Ga. wire or fork terminal

12 Volt, Group size U1

350 CCA, 33 amp/hr

Dimensions

Length

31.75” (80.6 cm)

23.63” (60.0 cm)

22.25” (56.5 cm)

220 lb. (100 kg)

250 lb. (114 kg)

Width

Height

Dry Weight

Gross Weight

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Label Locations – Item #165957K

WARNING

BURN HAZARD

Do not touch

hot muffler.

• Commercial-grade electric start engine

• Extend run 6.5 gallon fuel tank

• Maintenance-free brushless alternator design

• Smooth running focus mount isolation system

PN 39260

WARNING - BATTERY HAZARDS

BATTERIES:

1) contain caustic acid, 2) emit explosive gases, 3) can cause electric shock

ALWAYS use eye protection. Caustic acid and explosive gases can cause blindness or severe burns.

NO smoking, sparks, or flames.

NEVER touch both battery terminals at the same time with your hand or any non-insulated tools.

FLUSH immediately with water if battery acid contacts eyes, skin, or clothing.

CONNECT cables in correct sequence: FIRST RED to POSITIVE terminal, then BLACK to NEGATIVE

terminal. When disconnecting, DISCONNECT BLACK cable first, then RED.

NEVER charge a visibly damaged or frozen battery. ALWAYS read and follow charger instructions.

ATTENTION

IF GENERATOR IS TO BE STORED LONGER THAN 2 MONTHS,

charge battery with a trickle charger that is rated for 3 amps maximum.

A charged battery ensures reliable engine starting.

PN 779396

• Commercial-grade electric start engine

• Extend run 6.5 gallon fuel tank

• Maintenance-free brushless alternator design

• Smooth running focus mount isolation system

Always make sure safety labels are in place and in good condition. If a safety label

is missing or not legible, order new labels or unsafe operation could result.

To order replacement safety labels, call NorthStar Product Support at 1-800-270-0810.

On-Product Warning Labels

Part numbers

Description

Burn Warning

NorthStar

39260

779422

779423

Warning

779396

Battery Warning

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Component Identification - Item #165957K

Figure 1 (Ref. 1-8)

00591

Ref. Description

Circuit Breakers

Gas Cap with Gauge

120/240V 30A

6.5 Gallon Gas Tank

Locking device Receptacle

Grounding Post

120V 20A Duplex Receptacle

120V 15A Duplex Receptacle

Oil Drain Plug

Generator Head

Battery Box

Vibration Isolation Mount

Recoil

Fuel Valve Lever

Choke Lever

Engine Key Switch

Air Cleaner

Super Silent Muffler

Figure 2 (Ref. 10-18)

01804

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Component Identification - Item #165957K

REFERENCE GUIDE

Reference 1 – Circuit Breakers

This portable single phase generator has 1, 15 amp (A)

2, 20A, and 2, 30A push to reset circuit breakers to

protect against electrical overloads.

Reference 2 – 120/240V

Receptacle

The locking device is a 120/240V 30A NEMA L14-30R

receptacle.

This receptacle accepts a NEMA plug

number L14-30P. Use this receptacle if installing a

transfer switch.

Reference 3 – Grounding Post

Reference 4 – 120V Receptacle

Ground the generator via the grounding post, to a copper

pipe or rod that is driven into moist soil.

The duplex is a 120V 20A straight blade receptacle,

National Electrical Manufacturer’s Association (NEMA)

number 5-20R. This receptacle accepts NEMA plug

numbers 5-15P and 5-20P. Each receptacle on this

duplex is capable of drawing 20A.

Reference 5 – 120V Receptacle

Reference 6 – Oil Drain Plug

The duplex is a 120 volt (V) 15 amp (A) straight blade

receptacle, National Electrical Manufacturer’s Association

(NEMA) number 5-15R. This receptacle accepts NEMA

plug number 5-15P. The duplex is capable of drawing

15A out of either receptacle or a combination of both.

Refer to your Honda engine manual for oil change

recommendations.

Reference 7 – Air Cleaner

Reference 8 – Super Silent

Muffler

Refer to your Honda engine manual for air cleaner care.

4 dB less than Honda’s standard muffler.

Reference 10 – Gas Cap with

Gauge

The gas cap is extra large, creating a large hole for

refilling and a comfortable grip. You can monitor the fuel

level without removing the cap by using the fuel level

indicator built into the gas cap.

Reference 11 – 6.5 Gallon Gas

Tank

Large tank allows for extended run capabilities. Always

allow room for gasoline expansion by not filling the gas

tank completely full.

Reference 12 – Generator Head

Reference 13 – Battery Box

The electricity producing part of the generator.

The battery box provides protection for the battery and will

accept a standard lawn tractor size battery (Group U1-7).

See battery section for sizing.

Reference 14 – Vibration Isolation The engine and generator are mounted on rubber

Mounts

cylinders that absorb most of the engine vibration. This

feature eliminates the tendency of the machine to “walk”

which is common in engine powered equipment.

Grasp firmly when starting engine. Consult engine

manual for further instruction.

Reference 15 – Recoil

Reference 16 – Fuel Valve Lever

The engine has an ON-OFF valve mounted on the front

of the engine. Always keep this valve closed when the

generator is not in use.

Reference 17 – Choke Lever

Used during cold starts. Refer to the starting/stopping

instructions and the Honda engine owner’s manual for

further instruction.

Reference 18 – Engine Key

Switch

The engine key is located on the engine. Always locate

this switch and be familiar with its location before

operating the generator. Consult the Honda engine

owner’s manual for further instructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Load Planning & Management

WARNING

NEVER exceed the rated wattage capacity of your generator.

OVERLOADING may cause SERIOUS DAMAGE to the generator and

attached electrical devices, and may result in fire.

Your generator MUST BE SIZED PROPERLY to provide both the running and starting (surge)

wattage of the devices you will be powering. Before using your generator, determine the running

and starting wattage requirements of all the electrical devices you will be powering simultaneously.

The sum of the running and starting wattages of the devices being powered must not exceed the

continuous output rating of your generator. (The continuous output rating of your generator is listed

in the “Specifications” section of this manual.) Note that:

• Devices without electric motors such as light bulbs, radios, and televisions have the same

running and starting wattage.

• Devices with electric motors such as refrigerators, compressors, and hand tools typically

require a starting wattage that is 3 to 5 times greater than the running wattage.

The running and starting wattage requirements are often listed on a device’s nameplate. If wattage

is not given on the device’s nameplate, the wattage may be calculated by multiplying the nameplate

voltage by nameplate amperage, Watts = Volts X Amps.

Example conversion to watts:

120 Volts X 5 Amps = 600 Watts

If only the running voltage is given on the nameplate for a device with an electric motor, the starting

wattage can be approximated to be three to five times the running wattage.

Estimates for the running wattage requirements for common devices are listed in Table 1 below.

Guidance for starting wattages is provided in the table’s footnotes.

Table 1

Running

Watts

1700 (a,b) Jet pump

Running

Watts

800 (a)

1200

100

Device

Air conditioner (12.000 BTU)

Battery charger (20 Amp)

Belt sander (3”)

Chain saw

500

1000

1200

Lawn mower

Light bulb (100 Watt)

Microwave oven

700

Circular saw (6½”)

Coffee maker

2000 (a,b) Milk cooler

1800 (a,b) Oil burner on furnace

1100 (a)

300

Compressor (1 HP)

Compressor (3/4 HP)

Compressor (1/2 HP)

Curling iron

Dishwasher

Edge trimmer

Electric nail gun

Electric range (1 element)

Electric skillet

1400 (a,b) Oil-fired space heater (140,000 Btu)

1800 (a) Oil-fired space heater (85,000 Btu)

1400 (a) Oil-fired space heater (30,000 Btu)

400

225

150

4500

600 (a)

150

200

600 (b)

200

700

1200

500

1200

1500

1250

Oven

Paint sprayer, Airless (1/3 HP)

Paint sprayer, Airless (handheld)

Radio

Refrigerator

Slow cooker

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Load Planning & Management (cont’d)

Running

Watts

Running

Watts

2800 (a)

2000 (a)

1500 (a)

600 (a)

2000 (a)

500

Device

Furnace fan (1/3 HP)

Freezer

Device

1200 (a) Submersible pump (1-1/2 HP)

800 (b)

1200

1100

875

Submersible pump (1 HP)

Submersible pump (1/2 HP)

Sump pump

Table saw

Television

Hair dryer

Hand drill (1”)

Hand drill (1/2”)

Hand drill (3/8”)

Hand drill (1/4”)

Hedge trimmer

Home computer

Impact wrench

500

250

450

150

500

Toaster

Vacuum cleaner

VCR

Water Heater

Weed trimmer

1000

250

3000

500

(a) Hard-starting motors require 3-5 times the rated running watts

(b) For extremely hard to start loads such as air conditioners and air compressors, consult the equipment dealer to

determine maximum wattage

To calculate the running and starting wattage requirements for the devices you will be

powering, follow these steps:

1. Make a list of all electrical devices you will be powering at the same time with the generator.

2. List the greater of the running or starting wattage next to each device as obtained from the

devices’ nameplate or Table 1. If only the running wattage for a device with an electric

motor is known, the starting wattage can be estimated to be at least 3 times the running

wattage.

3. Add the wattages for all devices on your list. This total must be lower than the continuous

output rating of your generator.

Example:

Greater of

Device to be Powered

Light Bulb

Starting/Running Wattage

75 W

Refrigerator – 18 Cu. Ft.

Microwave

1600 W

700 W

Window AC

Sump pump (1/3 hp)

Total

1800 W

2100 W

6275W

In this example, the generator must have a continuous output of at least 6275 W in order to

power all of the devices simultaneously.

STAGGERING LOADS

You can increase the number of devices your generator can power by staggering the load on the

generator. For example, you could alternately power your refrigerator and air conditioner for

limited periods of time -- powering only one of the devices at a time and never powering both at the

same time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

There are a number of important steps required to set up your generator for initial use. These

steps are:

Steps for Installation / Initial Set-Up

1. Unpacking & delivery inspection.

2. Planning the power load to stay within the generator’s rated

capacity.

3. Setting up generator for the type of power generation you need:

a. portable power source, or

b. connected to a building as a back-up power source.

4. Selecting a site for using the generator.

5. Grounding.

6. Battery installation (electric start models only).

Each of these steps is discussed in detail below:

1. Unpacking & Delivery Inspection

You should inspect the generator immediately after you receive delivery.

See the “Machine Component Identification” section of this manual for a

diagram of the generator and its components.

• If you have missing components, contact Product Support at 1-800-270-0810.

• If you have damaged components, contact the freight company that delivered the unit and file a

claim.

2. Planning the Power Load

Plan your power load so that you do not exceed the generator’s rated capacity.

See the “Power Load Planning & Management” section of this manual to review how to plan and

manage power loads for the generator.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

3. Set-up either as a BUILDING BACK-UP or PORTABLE Power Source

This generator is designed to provide up to 8000W of electrical power. It can supply electricity in

two ways:

1. As a back-up, standby power source for a building. For this application, you must arrange

for a licensed electrician to connect the generator to your building’s electrical system via the

installation of an UL-approved transfer switch. The transfer switch must be installed in

accordance with building electrical code and guidelines supplied by your power company.

2. As a portable power source. You can plug appliances or tools directly into the generator’s

electrical outlets.

Specific requirements for each are given below.

Note: Regardless of whether you use your generator as a back-up power source connected to a

building or as a portable power source, you must not overload the generator. Overloading

may cause serious damage to the generator and attached electrical devices.

Using as a

Contact a licensed electrician to install a UL-approved transfer switch if

Back-up Power

Source for a

Building

you want to use your generator as a back-up power source for a building.

What does a transfer switch do? It:

a) Safely connects the generator to your building’s electrical system by

isolating your generator from your utility company’s power lines,

AND

b) Connects your generator to a critical subset of your building’s circuits

that are needed for emergency power needs.

If your generator will be connected to your building’s electrical system, it

MUST ALWAYS be isolated from the utility power grid with a UL-approved

transfer switch installed by a licensed electrician in compliance with all

applicable building and electrical codes, and in accordance with guidelines

supplied by your power company.

DANGER:

A transfer switch must be installed in order to isolate your

generator from the utility power grid. If your generator is NOT

properly isolated from the utility system, serious hazards will

arise:

♦ When your generator is running, it’s output will back feed into

the utility power line and transformer that are normally used to

provide you with power. The transformer will step up the

current to the normal line voltage. An unsuspecting utility line

worker working on what he thinks is a deactivated line could

be electrocuted.

♦ If your generator is connected (running or not) when utility

power is restored, your generator will be destroyed. It could

also explode or cause fire.

In addition to isolating your generator from the utility system, the transfer

switch connects your generator to a limited set of circuits in your building

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

that have been chosen as critical to operate during a power outage.

The generator cannot power your entire home -- you must work with the

installing electrician to determine which devices/appliances you wish to

power during an outage. The electrician can help you determine which

circuits and devices can be powered simultaneously without overloading the

generator.

(See the previous section of this manual entitled “Power Load Planning &

Management” for more information on load application and selection.)

When using the generator as a portable power source, you can plug

electric devices and appliances directly into the generator’s electrical

outlets.

Using as a

Portable Power

Source

There are three different kinds of electrical outlets on the generator:

1. One 120/240 Volt, 30 Amp locking receptacle (NEMA L14-30R

locking receptacle compatible with L14-30P mating plug).

2. One 120 Volt, 20 Amp duplex straight-blade receptacle (NEMA 5-

20R duplex receptacle compatible with NEMA 5-20P or 5-15P mating

plugs).

3. One 120 Volt, 15 Amp duplex straight-blade receptacle (NEMA 5-

15R receptacle compatible with NEMA 5-15P mating plug)

NEMA

5-20R

Duplex

NEMA

L14-30R

GROUNDING POST

NEMA

5-15R

Please read your owner's manual before operating, if you do not have

a manual or have questions, call customer service at 1-800-270-0810

FIG02679

(See more technical detail about these receptacles and their associated

circuit breakers in the “Machine Component Identification” section of this

manual.)

♦ Make sure you plug each electrical device/appliance into the correct

generator outlet based on the device’s plug configuration and

voltage/amperage rating. Never exceed the amperage rating of an outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

♦ Extension cords may be used to power devices that are located at a

distance from the generator. However, use only UL-listed, outdoor-rated,

grounded extension cords of the proper size. Use Table 2 below to choose

an adequately sized extension cord according to the amperage of the

device being used and the length of the cord.

Table 2

Current/Power

Maximum Extension Cord Length

Amps at Load

#10 Ga.

Cord

250’

125’

60’

#12 Ga.

Cord

150’

75’

#14 Ga.

Cord

100’

50’

#16 Ga.

Cord

75’

25’

10’

240V

(watts)

2400

4800

7200

35’

15’

25’

10’

9600

30’

12000

15’

WARNING:

Use of under sized extension cords can cause electric shock, fire, or

damage to connected devices.

♦ All extension and appliance cords must be in good condition and not worn,

bare, frayed, or otherwise damaged.

WARNING:

Use of damaged electric cords can cause electric shock or fire.

Note: If an extension cord becomes hot to the touch, it is overloaded or

damaged and must be replaced.

Northern Tool is NOT responsible for damage or injury resulting from

customer use of inadequate extension cords.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

4. Select a Suitable Site

Before using the generator, you must select a suitable OUTDOOR location for installation and

operation. This location should meet all of the criteria listed below.

WARNING:

You must choose a suitable site for operating your generator to avoid equipment damage

and/or injury and possible death from carbon monoxide poisoning, electric shock, or fire.

Choose a site that meets all of the criteria specified.

Dry, level surface The generator should be positioned on a dry, firm, level surface.

Ensure that the generator sits level and will not slide or shift during operation.

If applicable, block the generator’s wheels to prevent sliding and shifting.

WARNING: Carbon monoxide poisoning hazard

Outdoors only –

dangerous carbon

monoxide exhaust

The exhaust from your generator contains carbon monoxide (CO), a

poisonous gas that can kill. You cannot smell it, see it, or taste it.

Carbon monoxide exhaust is given off whether you are using gasoline,

natural gas, or propane as the fuel source to power the generator.

Follow the directions below for choosing a location to operate your

generator in order to avoid carbon monoxide poisoning.

The location you choose to operate the generator must be OUTDOORS

and away from all air intakes:

• Never run the generator inside any closed or semi-enclosed spaces (even if

outdoors), including homes, garages, basements, sheds, or boxes. These

spaces can trap poisonous gases, even if you run a fan or open windows.

• Place the generator so that the exhaust fumes will not be directed towards

people or building air intakes.

• Ensure that working, battery-operated or battery back-up carbon monoxide

alarms are used in any dwelling/structure that is in close proximity to the

running generator.

• Note that this generator is NOT designed or approved for use in vehicles

or marine applications. Never run the generator inside RVs or other

vehicles, on boats, or on pick-up truck beds.

WARNING:

Never attempt to attach ductwork to the muffler system to allow for

installation inside an enclosure. This could cause hot air deflection,

heat build-up, and increased exhaust back-pressure, resulting in

possible exhaust leakage or damage to the generator.

Adequate cooling The generator needs adequate, unobstructed flow of air to allow for

ventilation

proper cooling of engine and generator head.

WARNING:

Heat build-up from inadequate ventilation can result in fire, posing a

serious risk to nearby persons and structures.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

• Situate so there is adequate clearance around generator to allow for

cooling airflow so that heat does not build up.

• Never place the generator immediately adjacent to a building or other

structure – allow at least a 7’ clearance.

• Do not run the generator in close proximity to other heat-generating

equipment, such as another generator. The combined heat that is

generated may raise air temperature in the immediate area and there will

not be adequate cooling ventilation.

• Do not allow debris to accumulate and block airflow.

• Do not operate with a tarp, blanket, or cover surrounding the generator.

No wet conditions Choose a location where the generator will NOT be exposed to rain,

snow, or direct sunlight. Exposure to water can cause electric shock.

You may operate the generator under an outdoor, canopy-like structure of

heat-resistant material that is open on all sides. Make sure that all parts of

canopy are at least 7’ from exhaust, and allow for adequate clearance above

generator so that heat does not build up.

Hot exhaust

clearance

The exhaust gas from your generator is extremely hot and can cause

combustible materials to catch on fire.

• Make sure your generator’s exhaust system is at least 7 feet from all

combustible materials and buildings/structures.

• Equip the engine with a spark arrestor if the generator will be used near

any ignitable forest, brush, or grassy land. (See the “Specifications”

section of this manual to determine if your generator is already equipped.)

Make sure you comply with applicable local, state, and federal codes.

• Keep a fire extinguisher rated “ABC” nearby. Keep it properly charged

and be familiar with its use.

Away from

dust/dirt

Hearing

Do not use the generator in extremely dusty or dirty conditions.

Excessive dust and dirt can cause premature failure of the machine.

Generators can produce noise levels of up to 95 dB in close proximity,

which can be dangerous to human hearing with prolonged exposure.

protection

Hearing protection may be required for persons working within 15-20 feet of

the running generator for an extended period of time.

WARNING:

Never attempt to attach ductwork to the muffler system to lower noise

levels. This could cause hot air deflection, heat build-up, and

increased exhaust back-pressure, resulting in possible exhaust leakage

or damage to the generator.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

5. Grounding the generator

Always ensure the generator is properly grounded to prevent electrical shock.

You must always ground the generator by the following method when using the generator as a

portable electrical source:

1) Drive a ¾” or 1” copper pipe or rod into the ground close to the generator. The pipe/rod

must penetrate moist earth – the depth required will be dictated by local soil conditions.

Consult with an electrician.

2) Connect an approved ground clamp to the pipe.

3) Run a 10 gauge wire from the clamp to the generator grounding post located on the rear of

the generator head.

4) Do not connect the generator grounding post to a water pipe or a ground used by a radio

system.

10 Ga.

wire

Copper

Pipe/Rod

Grounding

Post

Ground

If a licensed electrician installs the generator with a connection to your building’s electrical circuit

for use as a back-up power system, grounding may alternatively be completed through the

building’s grounding system. Ask your electrician. If the generator is not grounded through your

building’s electrical system, follow the procedure above.

WARNING:

Operating the generator when it is not properly grounded can result in electrical shock.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation / Initial Set-Up

6. Battery Installation

Your generator’s engine is equipped with an electric starter which requires the installation of a 12-

volt lawn tractor size battery (Group U1). See the “Specifications” section of this manual for more

specific battery requirements for this generator model, such as minimum amperage or CCA rating.

The battery is to be supplied by the customer and should be installed in the protective battery box

located near the engine. Follow the instructions detailed below for connecting and disconnecting

the battery.

WARNING: Battery hazards

Batteries are hazardous because they contain caustic acid, can emit explosive gases, and can

cause electric shock. Caution must be exercised when making connections to a battery to

avoid shock and contact with the acid, and to prevent any sparking that could lead to an

explosion.

ALWAYS follow the general battery safety rules and instructions listed below.

General Battery

Safety Rules

• ALWAYS use eye protection when handling batteries.

• NEVER smoke or work near sparks or other sources of ignition.

• NEVER touch both battery terminals at the same time with your hand or

any non-insulated tools.

• If battery acid contacts skin or clothing, flush immediately with water and

neutralize with baking soda.

Connecting the

battery

Always connect the cables in the following sequence to avoid possible shock:

1. Find the battery cables located inside the battery box.

2. Connect the red cable to the positive(+) terminal of the battery.

3. Then connect the black cable to the negative(-) terminal of the battery.

Disconnecting the Always disconnect cables in the following sequence to avoid possible shock.

battery

1. First, disconnect the black cable from the negative(-) terminal of the

battery.

2. Next, disconnect the red cable from the positive(+) terminal of the

battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Once you have set up your generator for use, it is time to start your generator. The following

are the procedures necessary for safe, successful operation of your generator.

Operation Procedures

1. General Safety Rules for Operation

2. Preparing for Operation

3. Starting the Engine

4. Checking Generator Output

5. Connecting Electrical Loads (Portable Power Generation)

6. Stopping

7. Storage & Exercise of Generator

Each of these procedures is discussed in detail below:

1. General safety rules for operation

Before starting the generator, review the following general safety rules for operation:

WARNING:

Failure to follow safety rules may result in serious injury or death to the operator or

bystanders.

• Know proper use/how to stop. Be thoroughly familiar with proper use of the equipment and all

generator controls, output receptacles, and connections. Know how to stop the generator quickly if

needed (see “Operation, Step 6 - Stopping the Engine”).

• Instruct operators. The generator owner must instruct all operators in safe generator set-up and

operation. Only trained adults should set up and operate the generator – Do not let children operate.

• Intended use. Carefully read about and understand the intended use of this generator. Do not use for

other purposes, as unforeseen hazards or equipment damage may result.

• Under the influence. Never operate, or let anyone else operate, the generator while under the influence

of alcohol, drugs, or medication.

• Safety equipment / controls. Do not operate the generator unless all safety covers, guards, and barriers

are in place and in good working order, and all controls are properly adjusted for safe operation.

• Damaged. Do not operate the generator with damaged, missing, or broken parts.

• Modifications. Do not modify the generator in any way. Modifications can create serious safety hazards

and will also void the warranty.

• Engine speed. Never attempt to modify the engine speed setting. The engine speed is preset at 3600 RPM

for safe and optimal performance of the generator. If speed needs adjusting, it must be done by factory-

authorized personnel.

•

External fuel sources. Never attempt to connect external gasoline/diesel sources in order to increase

engine run time. Larger tank at pressure or higher elevation will cause gasoline to leak from carburetor

during operation. Fire or explosion could result.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

• Malfunction during operation. Immediately turn off the generator if any of the following conditions

arise during operation:

Excessive change in engine speed, slow or fast

Overheating in load connecting devices

Sparking or arcs from generator

Loss of electrical output

Receptacle damage

Engine misfire

Excessive vibration

Flame or smoke

Abnormal noise

• Adjusting / repairing. Always turn off generator and remove spark plug(s) or spark plug wire(s) before

working on the generator to prevent accidental starting. Always discharge the capacitor before working

on the generator head to prevent electrical shock. (See Maintenance & Repair section of this manual for

instructions on how to do this.)

• Carbon monoxide poisoning. The running engine gives off carbon monoxide, a poisonous gas that can

kill you. You CANNOT smell it, see it, or taste it. Follow all instructions for site selection and

positioning the generator, and avoid inhaling the exhaust. If you start to feel sick, dizzy, or weak while

using the generator, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have

carbon monoxide poisoning.

• Other exhaust dangers. This product contains or emits chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm. Avoid inhalation of exhaust.

• Wet conditions. Do not operate the generator or handle any electrical equipment while standing in water,

while barefoot, while hands are wet or while in the rain or snow. Electric shock may result.

• Ground fault circuit interrupter. Always use a ground fault circuit interrupter (GFCI) protected

extension cord (or outlet, if generator is equipped) in damp or highly electrical conductive areas and on

construction jobsites to prevent electrical shock.

• Avoid contact. Avoid contact with bare wires, terminals, connections, etc. while the unit is running.

• Electric shock accident. If an electric shock accident occurs, immediately shut down the source of

electrical power. If this is not possible, attempt to free the victim from the live conductor. Avoid direct

contact with victim. Use a nonconducting implement, such as a dry rope or board, to free the victim from

the live conductor. Apply first aid and get immediate medical help.

• Smoking/sparks. Never smoke near the running generator, and never operate near sources of sparks or

flames.

• Hot muffler. Never touch hot muffler, hot exhaust manifold, or engine cooling fins. Exhaust and engine

parts can be very hot and will burn you.

• Moving parts. Keep hands, feet, and apparel away from drive belts, fans, and other moving parts. Never

remove any drive belt or fan guard while the unit is operating.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

Static electricity and filling the gasoline tank:

Static electricity can initiate from ungrounded gasoline tanks or containers, from flowing gasoline, and

from persons carrying a static electric charge

Static electricity can explosively ignite gasoline vapors that are present during the fueling process, resulting

in serious burns to nearby persons. To avoid static electricity while fueling, certain steps must be followed

before and during the fueling process in order to minimize and safely dissipate static charge build-up:

• Touch a grounded metal object before starting. Always dissipate static charge from your body

before beginning the fueling process by touching a grounded metal object at a safe distance away from

fuel sources.

• Use a portable container to fill tank. Never fill the generator’s gas tank directly from the fuel pump –

the generator’s tank is not grounded and the high velocity flow of gasoline from a fuel pump can cause

static electric build-up. Use an approved portable container to transfer gasoline to the generator’s

tank.

• Fill container on the ground. Never fill the portable gas container while it is sitting inside a vehicle,

trailer, trunk, or pick-up truck bed. ALWAYS place container on the ground to be filled.

• Keep nozzle in contact with container. Keep nozzle in contact with the portable container at all times

while filling. Manually control the flow of gasoline; do NOT use the nozzle’s lock-open device.

• Use a portable container made of metal or conductive plastic. It will dissipate charge to ground more

readily.

About static electricity and fueling

Many common objects can accumulate and retain a static electric charge. Objects made of non-conductive

materials (e.g. plastics) easily accumulate and retain static electric charge, as can objects made of conductive

material (e.g. metal, water) if they are not electrically grounded. The static electric charge on an object, such

as a human body or plastic fuel tank/container, can reach as high as several thousand volts!

A static electric spark can be generated if the static electric charge stored on an object “jumps” to another,

less charged object. Such a spark can ignite invisible gasoline vapors that are present during fueling

situations.

Typical sources of static electric hazards during fueling

The following objects can accumulate a static electric charge and cause an ignition spark in typical fueling

situations:

1) Ungrounded tanks/containers. Any ungrounded fuel tank or container can accumulate a static electric

charge as a result of contact with other objects or friction during transportation. This static electricity

can discharge as a spark to the grounded gasoline dispenser nozzle, as the nozzle is first brought close to

the tank/container at the beginning of the fueling process.

2) Flowing gasoline. Most people are not aware that gasoline accumulates static electric charge while

flowing through a hose or pipe. This charge then transfers to and accumulates in the gas tank or container

that is being filled. The total amount of charge accumulation depends on the amount of gas pumped into

the container, the speed with which it is pumped, and whether or not the tank/container is grounded. If

sufficient static electric charge accumulates in the fuel tank or container during the fueling process, the

tank/container may discharge a spark to the grounded gasoline dispenser nozzle.

3) Persons. A person dispensing the gasoline can carry a static electric charge on their body, typically

resulting from contact with their car seat or electronics. The static electricity can discharge as a spark

between that person’s hand and either the grounded dispenser nozzle or the fuel tank opening.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

2. Preparing for Operation

Position generator in accordance with the instructions given in

“Installation & Initial Set-up, Step 4: Select a Suitable Site” of this

manual.

Position

generator

Operate outside only, on dry, level ground with adequate clearance and

ventilation.

WARNING: Carbon monoxide poisoning hazard

Generators give off carbon monoxide exhaust, a poisonous gas that can

kill. You CANNOT smell it, see it, or taste it. ONLY run generator

OUTDOORS and away from air intakes. NEVER run generator inside

any enclosed or semi-enclosed spaces, including homes, garages,

basements, sheds, boxes, pick-up truck beds, RVs, or boats. These spaces

can trap poisonous gases, EVEN if you run a fan or open windows.

Carbon monoxide exhaust is given off whether you are using gasoline,

natural gas, or propane to power the generator.

Ground

generator

Make sure the generator is grounded in accordance with instruction given

in “Installation & Initial Set-up, Step 5: Grounding the Generator” of

this manual.

WARNING: Electric shock hazard

Always ensure generator is properly grounded to prevent electrical shock.

Perform

Make sure that any regular maintenance has been performed as prescribed

in this manual in the “Maintenance & Repair” section.

scheduled

maintenance as

needed

1. Refer to the engine owner’s manual for engine maintenance instructions.

2. Make sure battery is charged. Charge as needed according to your

battery manufacturer’s instructions.

Check/add oil

Check the oil level using the dipstick and add oil as needed.

Using a funnel, add oil up to the FULL mark on the dip stick with the

recommended oil type for your engine and expected ambient conditions.

(See engine Owner’s Manual for oil type and capacity, and more detailed oil

check/fill instructions.)

WARNING: Burn hazard

Never open oil port while engine is running. Hot oil can spray over face

and body.

Notes:

o Low oil shutdown feature prevents the generator from starting without

sufficient oil.

o Engine is shipped without oil. You must add oil before first use.

IMPORTANT:

Under long, continuous-run operating conditions, be prepared to:

• Check engine oil level every time you refuel the engine.

• Change oil after the first 20 operating hours, and at least every 100

operating hours thereafter, or as directed in engine owner’s manual.

Check the gasoline level in the generator’s tank. If needed, fill tank with

fresh unleaded gasoline from a portable container, after first reading the

warnings and instructions below.

Check/fill

gasoline tank

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

WARNING: Gasoline fire/explosion hazard

Gasoline is highly flammable and explosive. Heat, sparks, and flames

can ignite gasoline vapors, which can become widespread during fueling.

A flash fire and/or explosion could result and cause serious injury or

death. Use extreme care when handling gasoline. Carefully follow all

the instructions in this section to avoid the following conditions which

could result in gasoline ignition:

•

gas vapor collection inside enclosures

static electric sparks

sparks from electric wiring, batteries, or running engines

sources of heat (such as a hot engine or exhaust)

open flames, including pilot lights

1) Before starting, review the following general safety precautions for fueling:

a) Never pump gasoline directly into the generator’s gas tank at a gas station –

high velocity flow from the pump could result in a static electric build-up

in the generator’s tank. Always use a portable container to fill the tank.

See warning box about static electric spark hazards below.

b) Fill gasoline tank OUTDOORS – never indoors.

c) Stay away from all sources of heat, sparks, and flames. Do not smoke.

2) Turn generator engine off and allow to cool for at least two minutes before

removing gas cap.

Note: A running or still-hot engine is hot enough to ignite fuel.

3) Remove generator gasoline cap.

4) Add gasoline through the fill opening:

- Use only a UL-approved portable gasoline container to transfer the gasoline

to the generator’s tank. Follow the safety warning and instructions below

for avoiding static electric sparking.

- Do NOT overfill the gasoline tank. Allow at least 1/2” of empty space

below the fill neck to allow for fuel expansion.

WARNING: Static electric spark hazard

A static electric spark can explosively ignite gasoline vapor, resulting in a

flash fire that could cause serious injury or death.

To avoid static electric sparking while filling the gasoline tank, the

following steps must be followed to minimize and safely dissipate static

electric charge build-up before and during the fueling process:

•

Always dissipate static charge from your body before beginning the

fueling process by touching a grounded metal object at a safe distance

from fuel sources.

•

Never fill the generator’s gas tank directly from the fuel pump – the

generator’s tank is not grounded and high velocity flow from the pump

can cause static electricity build-up. Use an approved portable

container to transfer gas to the generator’s tank.

•

Never fill the portable gas container while it is sitting inside a vehicle,

trailer, trunk, or pick-up truck bed. ALWAYS place container on the

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

ground to be filled.

•

Keep nozzle in contact with portable container while filling. Manually

control the flow of gasoline; do NOT use the nozzle’s lock-open

device.

A portable container made of metal or conductive plastic is preferred

because it dissipates charge to ground more readily.

5) Clean up gasoline spills /splashes immediately.

• If possible, move the generator away from spilled gasoline on the ground.

• Wipe up spilled gasoline, and wait 5 minutes for excess gasoline to

evaporate before starting engine.

• Gasoline soaked rags are flammable and should be disposed of properly.

• If gasoline is spilled on your skin or clothes, change clothes and wash skin

immediately.

6) Replace gasoline cap securely before starting engine.

7) Store extra gasoline in a cool, dry place in an UL-approved, tightly sealed

container.

IMPORTANT:

For continuous operation, be prepared to check and refuel the engine on a

regular basis. A tank of gasoline should last about 4 hours under 100%

load, and about 8 hours under 50% load.

Inspect Fuel

Inspect fuel system & check for leaks BEFORE starting generator.

System / Check Do not start generator until all needed repairs have been completed.

for Leaks

WARNING: Fuel leak hazard

Standard diesel fuel is combustible (with ethanol-diesel blends being

nearly as flammable as gasoline). Fuel leaks can result in fire. You can

be burned and seriously injured if the fuel system is not properly hooked

up or there is a fuel leak when you start the engine.

Inspect the entire fuel system. Look for:

• signs of leaks or deterioration,

• chafed or spongy fuel hose,

• loose connections,

• loose or missing fuel hose clamps,

• a damaged gasoline tank, or

• a defective gasoline shut-off valve.

Personal

Protection

1) Hearing can be damaged from prolonged, close-range exposure to the type of

noise produced by this generator. The use of ear plugs or other hearing

protection device is recommended for persons working within 15-20 feet of

the running generator for an extended period of time.

2) Loose or dangling apparel can become entangled in moving parts. Metal

jewelry can conduct electricity. Never wear jewelry or loose-fitting

clothing when starting or operating the generator.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

3. Starting the Engine

After you have completed the pre-start checklist procedures, you are ready to start the engine.

To start the engine:

1) Disconnect all loads to the generator.

2) Turn the gasoline line valve to the ON position.

3) For cold engine, move choke lever to full choke position. To restart a warm engine, move choke

lever to half choke or to RUN position.

4) Start the engine:

a) Using electric start –

i) Turn the engine key switch to the START position and hold it there until the engine starts.

NOTE: If the engine fails to start after 5 seconds, release key and wait 10 seconds

before attempting to start again. Cranking the electric starter for more than 5

seconds continuously can overheat and damage the starter motor.

ii) Release the key when the engine starts.

b) Using recoil start –

i) Turn the engine key switch to the ON position.

ii) Pull the starter grip lightly until you feel resistance, then pull the starter cord out briskly

and rapidly.

iii) Allow starter cord to return slowly.

5) When engine starts, move choke lever to RUN position.

6) Under long, continuous-run operating conditions, be prepared to:

a) Check and refuel the engine on a regular basis. A tank of gas should last about 4 hours under

100% load, and about 8 hours under 50% load. See engine owner’s manual for more detail.

WARNING:

A running engine is hot enough to ignite fuel. Never add fuel or remove gas cap if engine

is running or still hot. Let cool at least 2 minutes.

b) Check engine oil level each time you refuel.

c) Change oil after the first 20 operating hours, and at least every 100 operating hours thereafter,

as directed in the engine owner’s manual.

WARNING:

Never open oil port while engine is running. Hot oil can spray over face and body.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

4. Checking Generator Output

Although the speed of the engine was carefully adjusted at the factory so that the generator

produces the proper voltage and frequency, output voltage should be checked periodically to

ensure the generator is working properly before connecting loads to the generator.

WARNING:

The generator must be run at the correct speed in order to produce the

proper electrical voltage and frequency. Failure to do so could result in

damage to equipment powered by the generator and possible injury to the

individual.

Output voltage should be checked with a portable voltage meter:

1. Start engine and allow to warm up for five minutes. Do not connect any loads.

2. Use voltage meter to check output voltage

at the generator’s outlets/receptacles.

3. Measured voltage should be within the

following ranges:

a. 120V +/- 10% at 120V receptacles.

b. 240V +/- 10% at 240V receptacles.

4. If measured voltage is not within the specified range, have generator adjusted by factory

authorized personnel. Do not attempt to adjust the engine speed yourself.

NOTE:

All engines have a tendency to slow down when a load is applied. When

electrical loads are connected to the generator, the engine is more heavily

loaded and as a result the speed drops slightly.

Slight variation in

voltage/speed with

changing electrical

loads

This slight decrease in speed, together with the voltage drop within the

generator itself, results in a slightly lower voltage when the generator is

loaded to its full capacity than when it is running with no load.

Additionally, there may be small brief surges and drops in voltage as motors

connected to the generator cycle on or off.

The slight variation has no appreciable effect in the operation of motors,

lights, and most appliances.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

5. Connecting Loads

You will want to be careful when connecting loads so as not to overload the generator, especially if

you are powering devices with motors that require a higher starting power load.

Instructions are provided below for connecting loads when you are using the generator:

o As a portable power source

o Connected to a building as a back-up power source

WARNING:

Do not overload generator. Make sure that combined starting and running loads do

not exceed rated capacity of generator. Overloading the generator can cause damage

to the generator and attached electrical devices, and may result in fire.

Using as a

Portable Power

Source

Connect electrical loads one at a time according to the following

instructions:

1. Allow engine to reach operating speed by allowing it to warm up for

approximately 5 minutes before connecting electrical devices.

2. After engine is warmed up, begin by connecting the items that require

the highest wattage first. The recommended sequence is as follows:

a. Connect items with motors such as refrigerators, freezers, air

conditioners, or small hand tools, one at a time. Let each motor

stabilize before connecting the next device.

b. Connect any lights you are planning on powering.

c. Connect voltage sensitive equipment such as electronics via surge

protectors. Plug devices such as TV’s, computers, and microwaves

into a UL listed voltage surge protector, then plug the surge

protector into the generator.

Using as a

Each transfer switch installation will be unique.

Back-up Power

Source for a

Building

Proper instructions for how to safely bring the generator online with the

building’s electrical system should be provided by the installing electrician,

who should also provide personal instruction to the owner/operator.

Failure to follow the proper procedure as provided by the electrician could

expose persons to the hazards noted above.

6. Stopping

Stop the engine using the following steps:

1. Disconnect all loads to the generator.

2. Turn engine key switch to OFF position.

3. Turn gasoline line shut-off valve to OFF position.

4. Remove key from starter to prevent accidental starting of engine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

7. Storage & Exercise

When you are finished using the generator, you must:

o Disconnect all loads

o Shut off fuel supply

o Store the generator properly

o Plan on exercising the engine regularly unless the generator is prepared for long-term

storage.

Detailed instructions are provided below.

Disconnect loads & When you are finished using the generator, disconnect all loads and

turn off fuel supply turn off fuel supply:

1. Make sure all devices that were connected to the generator’s outlets

have been disconnected.

2. Check to be sure gasoline line shut-off valve is in OFF position.

Cool engine before Let engine cool for at least five minutes before storing. A hot engine can

storing

be a fire hazard.

Choose a storage

location

Store the generator in a location that is:

o Clean and dry

o Away from sources of heat, open flames, sparks, or pilot lights, even

if the generator’s fuel tank is empty. Residual fuel in the tank could

ignite.

o Away from extreme high or low temperatures.

Note: Do not store with battery charger always connected. Batteries that

are over-charged can boil themselves dry and produce excessive amounts of

hydrogen, an explosive gas.

Prevent accidental

starting

Remove key from starter (for electric start engines) and secure key in a

safe location, or remove spark plug(s) in order to ensure the generator

cannot be started accidentally in a storage location or by untrained persons.

Exercise generator The generator should be exercised regularly.

every 4 weeks

At least every four weeks, start the engine and let it run for 10 to 15 minutes

with a small load plugged in, such as a lamp or fan.

Monthly exercising of the generator will:

o Dry out any moisture that has accumulated in the windings. If left,

this moisture can cause corrosion in the winding.

o Ensure that the unit is operating properly should it be needed in an

emergency.

Perform regular

maintenance

Perform periodic maintenance as directed in this manual to keep the

generator in safe working condition.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation (cont’d)

Prepare engine for If you will not be able to exercise the generator regularly, you must

long term storage if prepare the engine for long term storage to prevent gum deposits from

needed

forming and causing malfunction of the engine.

Prepare engine for long term storage by:

o Removing all gasoline from the tank and carburetor

o Adding fuel stabilizer to the gasoline (following manufacturer’s

instructions)

Fuel stabilizer steps:

1. Ensure gasoline tank is full.

2. Add fuel stabilizer to fuel tank.

3. Run engine at least 10 minutes after adding stabilizer to allow it to

enter the fuel system.

4. Shut off engine

5. Disconnect spark plug wire and remove spark plug

6. Add one teaspoon oil through spark plug hole

7. Place rag over spark plug hole and turn starter (or pull the recoil) a

few times to lubricate the combustion chamber.

8. Replace spark plug, but do not reconnect the spark plug wire.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance & Repair

Inspect and maintain your generator as specified below in order to keep it in safe and optimal

working order. Follow all safety rules and recommended maintenance steps.

WARNING

ALWAYS shut off the engine, disconnect the spark plug(s) and discharge the capacitor

before cleaning, adjusting, or servicing the generator. Make sure all guards and shields are

replaced before using.

Note: The generator head is brushless and maintenance free. The bearing is a heavy-duty

sealed ball bearing which requires no maintenance or lubrication.

Maintenance & Repair

Read and follow these safety rules whenever you will be servicing the

generator:

Follow safety rules

• Turn off generator. Always turn off generator and remove spark plug(s) or

spark plug wire(s) before working on the engine or generator to prevent

accidental starting.

• Discharge capacitor. When the generator is shut down, the capacitor may

maintain a charge. Always discharge the capacitor before working on the

generator head to prevent electrical shock. Discharge using a screwdriver with an

insulated handle. While wearing safety glasses, touch opposite terminals of the

capacitor together with the tip of the screwdriver. If there is stored charge in the

capacitor, a spark will be generated thereby discharging the capacitor.

• Replace guards. Make sure all guards and shields are replaced after servicing

the generator.

• Repair. Major service, including the installation or replacement of parts, should

be performed only by a qualified electrical service technician. Obtain factory

approved parts from NorthStar Product Support at 1-800-270-0810.

• Replacement parts. If a part needs replacement, only use factory approved

repair parts. Replacement parts that do not meet specifications may result in a

safety hazard or poor operation of the generator and will void the warranty.

Perform engine

maintenance

Perform engine maintenance as specified in the engine owner’s manual.

Engine maintenance items include:

1. Changing oil and oil filter

2. Air filter check/replacement

3. Spark plug cleaning and replacement

4. Fuel filter check/replacement

5. Fuel tank cleaning.

Check receptacles

Check receptacles before each use to make sure they are not cracked or

broken.

If a receptacle is cracked or otherwise damaged, do not use until replaced

with an authorized factory part. Using cracked or damaged receptacles can be

both dangerous to the operator and destructive to the equipment.

Inspect fuel system / Inspect the fuel system and check for leaks on a regular basis.

check for leaks

1) Inspect the entire fuel system. Look for: signs of leaks or deterioration,

chafed or spongy fuel hose, loose connections, loose or missing fuel hose

clamps, damaged gasoline tank, or defective gasoline shut-off valve.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance & Repair (cont’d)

Check GFCI

(if equipped)

Once a month, test the Ground Fault Circuit Interrupter (GFCI) to

protect against electrical shock due to failure of the GFCI. (Only for

those models equipped with GFCI – See the “Specifications” section.)

To test the GFCI:

1. Depress the TEST button. The RESET button should extend from the

receptacle. If the RESET button does not extend, contact Northern Tool

for replacement parts.

2. Restore power to the GFCI by firmly pressing the RESET button back

into the receptacle until an audible click is heard.

Clean & inspect

spark arrestor

(if equipped)

Clean and inspect the spark arrestor muffler. (Only for those models

equipped with a spark arrestor – See the “Specifications” section.)

If the engine is equipped with a spark arrester muffler, clean and inspect it

regularly (follow manufacturer’s service instructions). Replace if damaged.

Keep generator clean.

If dust or debris accumulates on the generator, clean the generator with a

damp cloth or soft bristle brush. Do not allow air intakes to become blocked.

Keep generator

clean

Note: Do not spray generator with a garden hose or pressure washer.

Water may enter the generator and cause damage to the rotor, stator, or

internal windings.

Recharge and

maintain battery

(if electric start)

Inspect, recharge, and maintain your battery according to your battery

manufacturer’s instructions. (Only for those models equipped with electric

start.)

Do not store with battery charger always connected. Batteries that are over-

charged can boil themselves dry and produce excessive amounts of hydrogen,

an explosive gas.

IMPORTANT:

If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replace-

ment parts that do not meet specifications may result in a safety hazard or poor operation of the

generator.

Contact NorthStar Product Support at 1-800-270-0810 for any questions,

problems, or parts orders.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

TROUBLESHOOTING

Problem

Possible Causes

Possible Remedies

Engine will not start.

a) Low oil level.

b) Fouled spark plug.

c) Out of fuel.

a) Fill crankcase to proper oil level.

b) Clean or replace spark plug.

c) Fill fuel tank.

d) Stop switch in OFF position.

e) Battery is not charged.

d) Place switch in ON position.

e) Charge Battery. If battery will not

hold a charge, replace with new battery

(part # 31868).

Voltage too low.

a) Engine speed too slow.

b) Generator is overloaded.

a) Bring generator to a qualified

technician for adjustment.

b) Reduce the load. (See Power Load

Planning & Mgt. section of this manual.)

a) Disconnect load.

Circuit breaker trips.

Voltage too high.

a) Defective load connected to generator.

b) Defective receptacle.

c) Generator overloaded.

b) Replace receptacle.

c) Reduce the load. (See Power Load

Planning & Mgt. section of this manual.)

a) Bring generator to a qualified

technician for adjustment.

a) Engine speed too high.

Generator overheating. a) Generator is overloaded.

b) Insufficient ventilation.

a) Reduce the load. (See Power Load

Planning & Mgt. section of this manual.)

b) Make sure there is at least 3 feet of

clearance on all sides of generator.

a) Disconnect load.

No output voltage.

a) Defective load connected to generator.

b) Broken or loose wire.

b) Bring generator to a qualified

technician for repair.

c) Defective receptacle.

d) Defective stator.

c) Replace receptacle.

d) Bring generator to a qualified

technician for repair.

e) Defective rotor.

e) Bring generator to a qualified

technician for repair.

f) Defective capacitor.

a) Generator is overloaded.

f) Bring generator to a qualified

technician for repair.

a) Reduce the load. (See Power Load

Planning & Mgt. section of this manual.)

b) Clean or replace air filter.

a) Fill fuel tank.

Engine lacks power.

b) Dirty air filter.

a) Out of fuel.

b) Low oil level.

Engine shuts down

during operation.

b) Fill crankcase to proper oil level.

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Important Safety Information for Operation

This section provides a summary of the various safety procedures and measures that have been

presented throughout the manual. Keep this summary handy and refer to it to refresh your

memory about how to safely use your generator.

WARNING

Carefully read and make sure you understand the following safety information before using

the generator. Improper use or maintenance of the generator can result in serious injury or

death from carbon monoxide poisoning, electric shock, fire/explosion, or burns.

General

•

Read manual. Read this Owner’s Manual and the engine Owner’s Manual completely before attempting to

set-up and use the generator. Serious injury or death can result if safety instructions are not followed.

Instruct operators. The generator owner must instruct all operators in safe generator set-up and operation.

Do not allow anyone to operate the generator who has not read the Owner’s Manual and been instructed on its

safe use.

•

Adults only. Only trained adults should set up and operate the generator. Do not let children operate.

Under the influence. Never operate, or let anyone else operate, the generator while under the influence of

alcohol, drugs, or medication.

•

Intended use. Carefully read about and understand the intended use of this generator. Do not use for other

purposes, as unforeseen hazards or equipment damage may result.

Prohibition Against Modifications

Never modify or alter the generator in any way. Modifications can create serious safety hazards and will also

void the warranty.

•

Engine speed. Never attempt to modify the engine speed setting. The engine speed is preset at 3600 RPM for

safe and optimal performance of the generator. If speed needs adjusting, it must be done by factory-

authorized personnel.

•

Fuel/exhaust system. Never modify the exhaust system, fuel tanks, or fuel lines. Carbon monoxide

poisoning, fire, or explosion could result.

Guards. Do not operate generator unless all guards and cover shields, which prevent access to moving parts

and pinch points, are in place. Failure to guard the power transmission mechanisms may result in serious

injury or death.

Safety – Installation & Set-up

Battery Safety

Batteries are hazardous because they contain caustic acid, can emit explosive gases, and can cause electric shock.

Caution must be exercised when making connections to a battery to avoid shock and contact with the acid, and to

prevent any sparking that could lead to an explosion. Follow safety rules carefully when connecting battery to

generator:

•

Eye/skin protection. Always wear eye protection and protective clothing when connecting or disconnecting

battery.

•

Sparks/Smoking. Never smoke or work near sparks or other sources of ignition.

Electric shock. Never touch both battery terminals at the same time with your hand or any non-insulated tools.

Connection/disconnection sequence. ALWAYS connect and disconnect cables to the correct battery

terminals in the proper sequence:

o When CONNECTING the battery, connect the RED cable to the POSITIVE terminal FIRST.

o When DISCONNECTING the battery, disconnect the BLACK cable from the NEGATIVE terminal FIRST

Acid/skin contact. If battery acid contacts skin or clothing, flush immediately with water and neutralize with

baking soda.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Important Safety Information for Operation (cont’d)

Installation / Initial Set-up Safety

Dry, level surface. Situate generator on a dry, firm, level surface. Ensure generator sits level and will not

slide or shift during operation. Block wheels if applicable.

•

Operate OUTSIDE only – dangerous carbon monoxide exhaust! Generators give off carbon monoxide

exhaust, a poisonous gas that can kill. You CANNOT smell it, see it, or taste it. ONLY run generator

OUTDOORS and away from building air intakes. NEVER run generator inside homes, garages, sheds, or

other semi-enclosed spaces. These spaces can trap poisonous gases, EVEN if you run a fan or open windows.

Carbon monoxide is given off whether you are using gasoline, natural gas, or propane to power the generator.

No vehicle/marine use. This generator is NOT designed or approved for use in vehicles or marine

applications. Never run the generator inside RVs or other vehicles, on boats, or on pick-up truck beds.

Cooling ventilation. The generator needs adequate, unobstructed flow of air to allow for proper cooling of

engine and generator head. Situate so there is adequate clearance around generator to allow for cooling

airflow. Do not allow debris to accumulate and block airflow.

•

Grounding. Always ensure generator is properly grounded to prevent electrical shock. This generator is

equipped with a grounding post. Always complete the grounding path from the generator to a copper pipe/rod

driven into moist earth to a sufficient depth. Check with an electrician for local grounding requirements. If a

licensed electrician installs the generator with a connection to your building’s electrical circuit for use as a

standby power system, grounding will be complete through the building’s grounding system.

Isolate connection to building’s electrical circuit. Never plug the generator directly into a wall outlet.

ANY connection to a building’s electrical system MUST ISOLATE THE GENERATOR FROM UTILITY

POWER via an UL-approved transfer switch installed by a licensed electrician in compliance with all

applicable local building and electrical codes. If the generator is not isolated from the utility power system by

such means, generator output will backfeed into the utility power grid. This may result in injury or death to

utility power workers or others who contact the lines during a power outage. It may also cause the generator

to explode or cause fires when utility power is restored.

•

Wet conditions. Water conducts electricity. Do not operate generator where it is wet. Operate on a dry

surface under an open, canopy-like structure.

CO alarms. Ensure that working, battery-operated or battery back-up carbon monoxide alarms are used in

any dwelling/structure that is in close proximity to the running generator.

Hot exhaust - fires. Exhaust from engine can be extremely hot and cause fire. Position muffler at least 7’

from combustible objects during operation.

Spark arrestor. Equip engine with a spark arrestor if generator will be used near any ignitable forest, brush,

or grassy land. See the “Specifications” section of this manual to determine if your generator is already

equipped. Make sure you comply with applicable local, state and federal codes.

•

Fire extinguisher. Keep a fire extinguisher rated “ABC” by the National Fire Protection Association nearby.

Keep it properly charged and be familiar with its use.

Safety – Before Use

Know how to operate

Review safety rules. Before each use of this generator, review the “Rules for Safe Operation.” Failure to

follow these rules may result in serious injury or death.

Know how to operate. Be thoroughly familiar with all controls and with the proper use of the equipment.

Know how to stop the generator quickly if needed.

•

Personal protective equipment

Hearing protection. The use of ear plugs or other hearing protection device is recommended for those in

close proximity to the generator while it is operating.

Loose / dangling. Loose or dangling apparel can become entangled in moving parts. Metal jewelry can

conduct electricity. Never wear jewelry or loose-fitting clothing when operating the generator.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Important Safety Information for Operation (cont’d)

Gasoline Safety

Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Use

extreme care when handling:

•

Fuel outdoors. Fill fuel tank outdoors – never indoors. Gasoline vapors can ignite if they collect inside an

enclosure. Explosion can result.

Use approved container. Never pump fuel directly into engine at gas station. Static charge can build and

ignite fuel. Use an UL approved fuel container to transfer gas to the engine.

Running / hot engine. A running engine is hot enough to ignite fuel. Never add fuel or remove gas cap if

engine is running or still hot. Stop the engine and allow to cool at least two minutes before adding fuel.

Heat / flames / sparks. Stay away from sources of heat, flame, or sparks while adding fuel.

Don’t overfill. DO NOT overfill the gas tank. Allow at least 1/2” of empty space below the fill neck to allow

for fuel expansion.

•

Replace cap. Replace gas cap securely before starting engine.

Spills. Clean up fuel spills immediately. Move generator away from spilled fuel on the ground. Wipe fuel off

engine and wait 5 minutes for excess fuel to evaporate before starting engine. Gas soaked rags should be

disposed of properly.

•

On skin / clothes. If gasoline is spilled on your skin or clothes, change clothes and wash skin immediately.

Inspect fuel system. Check fuel system on a regular basis. Look for signs of leaks, deterioration, chafed or

spongy fuel hose, loose or missing fuel hose clamps, damaged fuel tank, or a defective fuel shut-off valve. Do

not start generator until needed repairs have been completed.

•

Gasoline storage. Store gasoline in a cool, dry place in an UL-approved, tightly sealed container.

Safety – During Use

•

Safety equipment / controls. Always operate the generator with all safety covers, guards, and barriers in

place and in good working order, and all controls properly adjusted for safe operation.

Know how to stop. Be thoroughly familiar with proper use of the equipment and all generator controls,

output receptacles, and connections. Know how to stop the generator quickly if needed.

Damaged. Do not operate the generator with damaged, missing, or broken parts.

Carbon monoxide exhaust. The running engine gives off carbon monoxide, a poisonous gas that can kill

you. You CANNOT smell it, see it, or taste it. If you start to feel sick, dizzy, or weak while using the

generator, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon

monoxide poisoning.

•

Other exhaust dangers. This product contains or emits chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm. Avoid inhalation of exhaust.

Smoking/sparks. Never smoke near the running generator, and never operate near sources of sparks or

flames.

Check output voltage. Check output voltage to ensure the generator is working properly before connecting

loads to the generator. Failure to do so could result in damage to equipment powered by the generator and

possible injury to the individual. Do not adjust output speed of engine to change voltage. If voltage is not

within specified range, have generator repaired by factory authorized personnel.

•

Stabilize before connecting loads. Start generator and let engine stabilize before connecting electrical loads.

Do not overload. Do not overload the generator. Make sure that combined starting and running loads do not

exceed rated capacity of generator or damage will result.

•

Protect sensitive electronics. Some electronic equipment, such as computers and audio/video equipment,

can be damaged by small fluctuations in the flow of power. Use a surge suppressor for any voltage-sensitive

electronic equipment you will be powering with the generator.

•

Wet conditions. Do not operate the generator or handle any electrical equipment while standing in water,

while barefoot, while hands are wet or while in the rain or snow. Electric shock may result.

Ground fault circuit interrupter. Always use a ground fault circuit interrupter (GFCI) protected extension

cord (or outlet, if generator is equipped) in damp or highly electrical conductive areas and on construction

jobsites to prevent electrical shock.

•

Electrical cords. Use only UL-listed, outdoor-rated, three prong extension cords of the proper size. All

extension and appliance cords must be in good condition and not worn, bare, frayed, or otherwise damaged.

Use of inadequate or damaged electric cords can cause electric shock or fire.

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Important Safety Information for Operation (cont’d)

•

Avoid contact. Avoid contact with bare wires, terminals, connections, etc. while the unit is running.

Electric shock accident. If an electric shock accident occurs, immediately shut down the source of electrical

power. If this is not possible, attempt to free the victim from the live conductor. Avoid direct contact with

victim. Use a nonconducting implement, such as a dry rope or board, to free the victim from the live

conductor. Apply first aid and get immediate medical help.

•

Hot muffler. Never touch hot muffler, hot exhaust manifold, or engine cooling fins. Exhaust and engine parts

can be very hot and will burn you.

Moving parts. Keep hands, feet, and apparel away from drive belts, fans, and other moving parts. Never

remove any drive belt or fan guard while the unit is operating.

•

Refueling. DO NOT refuel the engine until it has cooled at least two minutes.

Malfunction during operation. Immediately turn off the generator if any of the following conditions arise

during operation:

Excessive change in engine speed, slow or fast

Overheating in load connecting devices

Sparking or arcs from generator

Loss of electrical output

Receptacle damage

Engine misfire

Excessive vibration

Flame or smoke

Abnormal noise

•

Adjusting / repairing. Always turn off generator and remove spark plug(s) or spark plug wire(s) before

working on the generator to prevent accidental starting.

Safety – After use

Cool engine before storing. Let engine cool for at least five minutes before storing. A hot engine can be a

fire hazard.

•

Shut off fuel supply. Make sure gasoline shut-off valve is in the OFF position.

Prevent accidental starting. When generator is not in use, remove key from starter (key start engines) and

secure in a safe location, or remove spark plug(s) in order to ensure that generator cannot be started in a

storage location or by untrained persons.

•

Storage location. Store the generator in a dry location away from sources of heat, open flames, sparks or

pilot lights – such as water heaters, space heaters, furnaces, clothes dryers, or other gas appliances – EVEN IF

the generator’s gas tank is empty. Residual gasoline could ignite.

•

Exercise regularly. Exercise generator every four weeks to dry out moisture that accumulates in the

windings. If generator cannot be exercised on a regular basis, prepare generator for long term storage.

Periodic maintenance. Perform periodic maintenance as directed in this manual to keep the generator in safe

working condition.

Safety - Inspection/Maintenance

Inspect and maintain your generator on a regular basis and repair as needed to keep it in safe working condition:

•

Turn off generator. Always turn off generator and remove spark plug(s) or spark plug wire(s) before

working on the engine or generator to prevent accidental starting.

•

Discharge capacitor. When the generator is shut down, the capacitor may maintain a charge. Always

discharge the capacitor before working on the generator head to prevent electrical shock.

Replace guards / shields. Make sure all guards and shields are replaced after servicing the generator.

Replacement parts. If a part needs replacement, only use parts that meet the manufacturer’s specifications.

Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the

generator and will void the warranty.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Generator Exploded View Rev - K

Download from Www.Somanuals.com. All Manuals Search And Download.

Generator Exploded View Rev - K

Ref #

Part #

Description

Qty

38759

33321

Fuel Tank Assembly

Fuel Cap

777352

30754

779422

777834

779423

32833

Battery Box

Leather Washer

Decal

Hose Clamp

Warning Decal

Roll Cage

39260

31335

Hot Muffler Sticker

Honda GX390 Engine, 13 HP

Generator Head

Generator Cover

Engine Ground Wire

Generator Bracket

Battery Cable, Negative

Isolation Mount

Bottom Bracket

Generator Base

Bolt, 5/16-18 X 2”

Clip Nut, #10-32

Screw, #10-32 X .75

Positive Battery Cable

Control Panel Face Assembly

Control Panel Housing

Grommet

Top Bracket

Nameplate

Fuel Filter

1/4” Fuel Line

Engine Cover

Battery Warning Decal

Protective Sleeve

33”

778530A

777304

306459

777621

777108

34172

32844

778483

82018

82067

82007

777164

777620

38180

306579

32848

34176

30755

777345

38184

779396

30753

1.38ft

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Diagram Rev - K

Diag #

Part #

Description

Qty

306438

31736

306422

15 Amp, 120 Volt Receptacle (NEMA 5-15R)

20 Amp, 120 Volt Receptacle (NEMA 5-20R)

30 Amp, 120/240 Volt Locking Receptacle

(NEMA L14-30R)

306429

306433

38191

Grounding Post

Thermal Circuit Breaker, 15 Amp

Wiring Harness

(Connects generator to Control Panel)

#8-32 X ½ Button Head Cap Screw

#8-32 Lock Nut

Thermal Circuit Breaker, 20 Amp

Thermal Circuit Breaker, 30 Amp

Wire Assembly (B25, B27)

Wire Assembly (W23, W24, G22, G23, G24)

Control Panel Face

¼ USS Flat Washer

Cable Tie

Black Terminated Wire

Green Terminated Wire

White Terminated Wire

B23

B24

B26

B28

B29

B31

G22

W25

82004

82005

30643

31086

31107

306604

30975

82085

82155

31106

31108

31109

306599

30660

306601

306603

30977

Download from Www.Somanuals.com. All Manuals Search And Download.

Generator Head Exploded View Rev - K

Item #

Part #

Description

Qty

38266

38267

38268

38269

38270

777304

38271

38272

38273

307479

38275

38276

38277

38278

38279

38280

307481

Mount Plate (J609B)

Fan Bolts

Fan

Drive End Bracket

Enclosing Band

End Cover

End Cover Plug

Stator

Rotor

Diode

Securing Stud

Bearing

Nut

Non Drive End Bracket

Capacitor

Bracket Securing Stud

Varistor

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Washer Dryer W 4800 User Manual
Miller Electric Welder SuitCase 8VS User Manual
NETGEAR Computer Accessories WNA1100 100ENS User Manual
Nissan Automobile Parts VQ35DE User Manual
NordicTrack Treadmill NTL14942 User Manual
NordicTrack Treadmill NTL129055 User Manual
One for All Universal Remote UR2 DTA User Manual
Onkyo Stereo Receiver TX SR703E User Manual
Panasonic Blood Pressure Monitor EW3122 User Manual
Panasonic Network Card 2SA2079 User Manual