Model No. NTSY39210
Serial No.
USER’S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal
(Behind Backrest)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight system.
1. Read all instructions in this manual before
using the weight system. Use the weight sys-
tem only as described in this manual.
9. Always wear athletic shoes for foot protec-
tion while exercising.
10. The weight system is designed to support a
maximum user weight of 300 pounds.
2. It is the responsibility of the owner to make
that all users of the weight system are ade-
quately informed of all precautions.
11. Make sure that the weight pin is fully inserted
into the weight stack before you exercise.
3. The weight system is intended for home use
only. Do not use the weight system in any
commercial, rental, or institutional setting.
12. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
4. Use the weight system only on a level sur-
face. Cover the floor beneath the weight sys-
tem to protect the floor.
13. The decal shown here
has been placed on the
weight system in the
location shown on page
4. If the decal is missing
or illegible, call our toll-
free Customer Hot Line
at 1-888-825-2588 and
order a free replacement
decal. Apply the decal in
the location shown.
5. Make sure that all parts are properly tight-
ened each time you use the weight system.
Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the weight system at all times.
7. Keep hands and feet away from moving parts.
8. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
Warning Decal
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile NordicTrack®
GRT 950 weight system attachment. The weight sys-
tem attachment is designed to develop the muscle
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please note
groups of the lower body. Whether your goal is to tone the product model number and serial number before
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the attachment
will help you to achieve the specific results you want.
calling. The model number is NTSY39210. The serial
number can be found on a decal attached to the
attachment (see the front cover of this manual).
For your benefit, read this manual carefully before
using the weight system attachment. If you have
additional questions, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
ASSEMBLED
DIMENSIONS:
Height: 84 in.
Width: 86 in.
Length: 72 in.
Warning
Decal
Hack Squat
Release Handle
Foot Plate
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Make sure you have the following tools:
• Two adjustable wrenches
• One standard screwdriver
• One phillips screwdriver
Make Assembly Easier for Yourself
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by most people. Before
beginning assembly, make sure to read the
information on this page. This brief intro-
duction will save you much more time than
it takes to read it.
• One rubber mallet
• You will also need grease or petroleum jelly, a
small amount of soapy water, and clear tape or
masking tape.
Assembly Requires Two Persons
Note: Assembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
For your convenience and safety, assemble the
weight system with the help of another person.
Set Aside Enough Time
How to Identify Parts
Due to the many features of the weight system, the
assembly process will take a few hours. By setting
aside plenty of time and by deciding to make the
task enjoyable, assembly will go smoothly. You may
want to assemble the weight system over a couple
of evenings.
To help you identify the small parts used in assembly,
we have included a PART IDENTIFICATION CHART
in the center of this manual. Place the chart on the
floor and use it to easily identify parts during each
assembly step. Note: Some small parts may have
been pre-attached. If a part is not in the parts
bag, check to see if it has been pre-attached.
Select a Location for the Weight System
How to Orient Parts
Because of its weight and size, the weight system
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.
As you assemble the weight system, make sure that
all parts are oriented exactly as shown in the draw-
ings.
How to Unpack the Box
Tightening Parts
To make assembly as easy as possible, we have
divided the assembly process into four stages. The
parts needed for each stage are found in individual
bags. Important: Wait until you begin each stage
to open the parts bag for that stage. Place all
parts of the weight system in a cleared area and
remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Questions?
If you have questions after reading the assembly
instructions, please call our Customer Service
Department at 1-888-825-2588.
The Four Stages of the Assembly Process
Frame Assembly—You will begin by assembling
the base and the uprights that form the skeleton of
the weight system.
Cable Assembly—During this stage you will
attach the cables and pulleys that connect the
arms to the weights.
Arm Assembly—During this stage you will
Seat Assembly—During the final stage you will
assemble the arms and the leg lever.
assemble the seats and the backrests.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Frame Assembly
C
1.
Before beginning assembly, make sure that
you understand the information on page 5.
This brief introduction will save you much
more time than it takes to read it.
D
A
Remove the 50mm x 75mm inner cap w/ slot (A),
the four M10 x 67mm carriage bolts (B), and the
four M10 nylon locknuts (C) from the rear base
(D).
B
B
2
31
2. Press a 50mm Square Inner Cap (25) into the
indicated end of the Hack Squat Base (1).
25
Insert four M10 x 67mm Carriage Bolts (33) up
through the bottom of the Hack Squat Base (1).
Slide the Hack Squat Base into the rear base (C).
Note: If the Bolts fall out, stick a piece of tape
over the bolt heads to hold them in.
D
33
Secure the Hack Squat Base (1) to the rear base
(D) with four M10 x 25mm Bolts (31).
33
1
3. Press a 75mm x 50mm Inner Cap (21) into the
top of the Hack Squat Upright (4).
3
21
C
Remove the indicated two M10 x 45mm bolts (E),
two M10 washers (F), and two M10 Nylon
Locknuts (C) from the left upright (G).
39
Attach the Hack Squat Upright (4) to the two M10
x 67mm Carriage Bolts (33) in the Hack Squat
Base (1) with two M10 Locknuts (32). Do not
tighten the Locknuts yet.
E
F
4
G
Attach the Hack Squat Upright (4) to the left
upright (G) with two M10 x 50mm Bolts (39) and
two M10 Nylon Locknuts (C).
32
32
33
1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the 75mm x 50mm Spacer (48) into the
82mm x 57mm Outer Cap (26). Press the Outer
Cap onto the Hack Squat Leg (2).
4
32
26
48
4
38
Attach the Hack Squat Leg (2) to the two M10 x
67mm Carriage Bolts (33) in the Hack Squat
Base (1) with two M10 Locknuts (32).
36
32
Attach the Hack Squat Leg (2) to the Hack Squat
Upright (4) with two M10 x 95mm Bolts (38), two
M10 Washers (36), and two M10 Locknuts (32).
32
2
32
Tighten the M10 Locknuts (32) used in steps 3
and 4.
1
33
5
Arm Assembly
14
14
5. Press two 75mm x 50mm Inner Caps (21) into
the Hack Squat Bracket (3). Press four 34mm
Bushings (14) into the Hack Squat Bracket.
29
37
16
21
Attach the Hack Squat Bumper (16) to the Hack
Squat Bracket (3) with an M4 Washer (37) and an
M4 x 20mm Screw (29).
3
21
6. Press two 34mm x 19mm Bushings (13) into the
Hack Squat Upright (4).
6
30
13
31
13
Attach the Hack Squat Bracket (3) to the Hack
Squat Upright (4) with a 25mm x 86mm Pivot Rod
(15), two M10 Large Washers (30), and two M10
x 25mm Bolts (31).
30
15
31
7. Press a 75mm x 50mm Inner Cap (21) into the
end of the Hack Squat Frame (5). Press a 50mm
x 40mm Inner Cap (22) into the bottom of the
backrest tube on the Frame. Press two 34mm x
19mm Bushings (13) into the Hack Squat Frame.
7
21
13
5
13
Slide two Foam Pads (7) onto the Hack Squat
Frame (5).
22
Attach the Release Handle (10) to the Hack
Squat Frame (5) with an M6 x 25mm Allen Head
Screw (28).
7
10
9
Slide the Handgrip (8) and the Long Handgrip (9)
onto the indicated handles of the Hack Squat
Frame (5). Press two 25mm Round Inner Caps
(42) into the handles on the Frame.
42
8
42
28
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach the Hack Squat Frame (5) to the Hack
Squat Bracket (3) with a 25mm x 86mm Pivot
Rod (15), two M10 Large Washers (30), and two
M10 x 25mm Bolts (31).
8
5
12
Squeeze the Release Handle (10) and align the
Hack Squat Pin (12) with a hole in the arm on the
Hack Squat Bracket (3). Let go of the Release
Handle so that the Hack Squat Pin engages the
hole.
30
3
10
31
31
15
Arm
30
9
Cable Assembly
9. Locate the Hack Squat Cable (20). Attach the
Cable and a Pulley (19) to the Hack Squat
Bracket (3) with an M10 x 60mm Bolt (24), four
M10 Washers (36), and an M10 Locknut (32).
32
24
36
3
36
20
19
10. Wrap the Hack Squat Cable (20) around a Pulley
(19). Attach the Pulley, along with another Pulley,
inside the bracket on the Hack Squat Base (1)
with an M10 x 70mm Bolt (40) and an M10
Locknut (32).
10
20
19
32
40
Bracket
1
11. Route the Hack Squat Cable (20) over the
Pulley (19) attached to the Hack Squat Bracket
(3) in step 9. Make sure that the Cable is routed
over the Pulley from the back to the front.
11
3
19
20
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Route the Hack Squat Cable (20) around the
other Pulley (19) attached to the Hack Squat
Base (1) in step 10, and through the Hack Squat
Leg (2).
12
20
19
1
2
13. Route the Hack Squat Cable (20) under a Pulley
(19) and through the Hack Squat Upright (4).
13
4
Attach the Pulley inside the Upright with an M10 x
65mm Bolt (35), two 15mm x 12mm Spacers (17),
two M10 Washers (36), and an M10 Locknut (32).
40
20
36
32
35
17
19
14. Wrap the Hack Squat Cable (20) around a Pulley
(19). Attach the Pulley and a Cable Trap (18) to
the left hole in the top of the Hack Squat Upright
(4) with an M10 x 125mm Bolt (41), a 15mm x
8mm Spacer (46), an M10 Washer (36), and an
M10 Locknut (32).
14
19
41
18
46
36
18
46
Wrap the Hack Squat Cable (20) around another
Pulley (19). Attach the Pulley and a Cable Trap
(18) to the other hole in the Hack Squat Upright
(4) in the same manner.
36
Left
Hole
32
20
Make sure the Cable Traps (18) are positioned
to hold the Hack Squat Cable (20) in the
grooves of the Pulleys (19).
4
15. Attach the end of the Hack Squat Cable (20) to
the end of the rear cable (F) with a Cable Clip
(34).
15
20
34
F
9
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Seat Assembly
16. Attach the Hack Squat Backrest (6) to the Hack
Squat Frame (5) with four M6 x 16mm Bolts (27).
5
27
6
17. Make sure that all parts have been properly tightened. Before using the weight system, pull each cable a
few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move
smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may
be damaged when heavy weight is used. See the CABLE DIAGRAM on page 11 for proper cable rout-
ing.
ADJUSTMENTS
This section explains how to adjust the weight system attachment. Make sure all parts are properly tightened each
time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned with a
damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE HACK SQUAT
Adjustment
Holes
Stand on the foot plate on the Hack Squat Base (1)
with your shoulders under the Foam Pads (7).
Squeeze the Release Handle (10) and move the
Hack Squat Frame (5) to the desired position.
Release the Handle, and engage the Hack Squat Pin
(12) into an adjustment hole in the Hack Squat
Bracket (3).
5
3
12
7
10
WARNING:
Make sure the Hack
Squat Pin (12) fully engages the Hack Squat
Bracket (3) before you use the Hack Squat.
1
Foot
Plate
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAM
The cable diagram shows the proper routing of the
Hack Squat Cable (20). Use the diagram to make
sure that the cable has been assembled correctly. If
the cable has not been correctly routed, the weight
system will not function properly and damage may
occur. The numbers show the correct route for the
cable. Make sure that the cable traps do not touch
or bind the cable.
Hack Squat Cable (20)
7
6
3
1
8
5
4
2
WEIGHT RESISTANCE CHART
This chart shows the approximate
weight resistance for the hack
squat station. “Top” refers to the
WEIGHT
PLATES
HACK SQUAT
(lbs.)
WEIGHT
PLATES
HACK SQUAT
(lbs.)
5-lb. top weight. The other num-
bers refer to the seven 5-lb.
Top
1
58
70
12
13
14
15
16
17
18
19
20
21
22
23
211
226
242
257
272
289
305
319
335
351
366
381
weight plates and the sixteen 10-
lb. weight plates. Note: The
actual resistance may vary due
to differences in individual
weight plates, as well as fric-
tion between the cables, pul-
leys, and weight guides.
2
79
3
85
4
105
116
127
135
149
165
181
196
5
6
7
8
9
10
11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART—Model No. NTSY39210
R0303A
M4 x 20mm Screw (29)
M6 x 16mm Bolt (27)
M6 x 20mm Allen
Head Screw (23)
34mm x 19mm Bushing (13)
M6 x 25mm Allen
Head Screw (28)
31mm Round Inner Cap (42)
M10 x 25mm Bolt (31)
34mm Bushing (14)
M10 x 50mm Bolt (39)
M10 x 60mm Bolt (24)
M4 Washer (37)
M7 Nut (47)
M10 x 65mm Bolt (35)
M10 x 67mm Carriage Bolt (33)
M10 Locknut (32)
M10 Washer (36)
M10 x 70mm Bolt (40)
M10 x 95mm Bolt (38)
M10 Large Washer (30)
M10 x 125mm Bolt (41)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTSY39210
R0303A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
2
1
1
1
1
1
4
4
2
1
2
2
6
1
4
1
1
1
1
Hack Squat Base
Hack Squat Leg
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
#
1
4
1
1
4
8
11
4
1
1
10
1
2
2
1
2
2
1
1
1
2
2
1
1
82mm x 57mm Outer Cap
M6 x 16mm Bolt
Hack Squat Bracket
Hack Squat Upright
Hack Squat Frame
Hack Squat Backrest
Foam Pad
Handgrip
Long Handgrip
Release Handle
Release Cable
Hack Squat Pin
34mm x 19mm Bushing
34mm Bushing
25mm x 86mm Pivot Rod
Hack Squat Bumper
15mm x 12mm Spacer
Cable Trap
M6 x 25mm Allen Head Screw
M4 x 20mm Screw
M10 Large Washer
M10 x 25mm Bolt
M10 Locknut
M10 x 67mm Carriage Bolt
Cable Clip
M10 x 65mm Bolt
M10 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
M4 Washer
M10 x 95mm Bolt
M10 x 50mm Bolt
M10 x 70mm Bolt
M10 x 125mm Bolt
31mm Round Inner Cap
Cable Attach
Release Cable Cover
Spring
15mm x 8mm Spacer
M7 Nut
Pulley
Hack Squat Cable
75mm x 50mm Inner Cap
50mm x 40mm Inner Cap
M6 x 20mm Allen Head Screw
M10 x 60mm Bolt
50mm Square Inner Cap
75mm x 50mm Spacer
User’s Manual
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTSY39210
R0303A
13
21
21
18
23
47
13
19
41
12
43
45
5
46
47
22
44
11
19
36
32
18
46
7
36
30
4
27
39
13
27
9
10
30
31
13
15
31
28
8
6
38
42
36
32
17
36
14
14
30
3
31
17
36
15
30
29
37
32
19
35
16
32
31
36
21
20
36
21
24
19
31
31
32
20
34
26
48
25
19
32
32
33
2
32
19
1
40
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through
Friday, 6 a.m. until 6 p.m. MST (excluding holidays). Please be prepared to give the following information:
1. The MODEL NUMBER of the product (NTSY39210)
2. The NAME of the product (NordicTrack® GRT 950 weight system attachment)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
center of this manual)
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® GRT 950 weight system attachment (“Product”) is warranted to be free of all defects
in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product frame for five years after the date of pur-
chase. ICON warrants all other parts for one year after the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component, pro-
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our
option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper
assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and
maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-
ed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them your name
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for serv-
ice where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-
lem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 192817 R0303A
Printed in China © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|