Model No. NTL25530
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
your local NordicTrack dealer or call 1-800-
806-3651 and order part number 146148.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 300 pounds.
8. Never allow more than one person on the
treadmill at a time.
17. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the on/off circuit breaker.)
10. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 26.) You
must be able to safely lift 45 pounds (20 kg) to
raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
your CD player or VCR when you are not
using them.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
25. Inspect and properly tighten all parts of the
treadmill regularly.
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
26. Never insert or drop any object into any
opening.
27.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
23. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video 28. This treadmill is intended for in-home use
program.
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
24. Always remove iFIT.com CDs and videos from
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been placed on your treadmill. If the decal is miss-
ing or illegible, please call our Customer Service Department, toll-free, to order a free
replacement decal (see ORDERING REPLACEMENT PARTS on page 35). Apply the
decal in the location shown. Note: The decal is not shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack®
7200 R treadmill. The 7200 R treadmill offers an im-
pressive array of features to make your home work-
outs more enjoyable and effective. And when you’re
not exercising, the unique 7200 R treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
Service Department toll-free at 1-888-825-2588,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial num-
ber before calling. The model number of the treadmill
is NTL25530. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
For your benefit, read this manual carefully before
using the 7200 R treadmill. If you have questions
after reading this manual, please call our Customer
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Water Bottle Holder*
Fan
Console
Handrail
Latch Knob
Pulse Sensor
Key/Clip
LEFT SIDE
On/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
RIGHT SIDE
Flexible Walking Platform
Rear Roller
*No water bottle is included.
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own flat-bladed screwdriver
wrench
, wire cutters
, and adjustable
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the treadmill or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt or foot pads,
simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. Slide the treadmill out of the box. Insert the three Cage
1
Nuts (96) into the three indicated holes in the treadmill.
96
To insert each Cage Nut (96), first hook one side of the
Cage Nut into a hole and then use a flat-bladed screw-
driver to press the other side into the hole, as shown.
96
2. With the help of a second person, carefully raise both
Uprights (99) to a vertical position. Press the Latch Knob
Sleeve (111) into the left Upright and hold the Latch Knob
Spacer (112) against the left Upright.
2
99
113
Remove the Latch Knob (113) from the Latch Pin (107).
Make sure that the Latch Pin Collar (109) and the Spring
(110) are on the Latch Pin. (Note: If there are two Latch
Pin Collars, place one on each side of the Spring.) Insert
the Latch Pin into the Latch Knob Sleeve (111) and the
Left Upright (99).
112
110
107
111
109
Tighten the Latch Knob (113) onto the Latch Pin (107).
3. With the help of a second person, raise the Walking
Platform (24) to the storage position and make sure that
the latch pin is engaged as described on page 26.
3
24
Position the Base Plate (91) on the treadmill as shown.
Attach the Base Plate with the three Base Plate Screws
(92). Note: It may be helpful if a second person tips the
treadmill slightly as you tighten the Screws.
92
If the treadmill rocks slightly, turn one or both of the
Leveling Feet (127) under the Uprights (99) until the
rocking motion is eliminated. Carefully lower the Walking
Platform (24) to the floor as described on page 27.
99
127
127
91
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Cut the plastic tie holding the Upright Wire Harness (119)
in the right Upright (99). Have a second person hold the
Handrails (83) near the Uprights. Connect the Upright
Wire Harness to the wires extending from the Console
Base (130). The connectors should slide together
easily and snap into place. If they do not, turn one
connector and try again. Then, insert the connectors
and the Upright Wire Harness into the hole in the right
Upright.
4
130
119
Set the Handrails on the Uprights, being careful not to
pinch the wires.
99
83
5. Insert two Handrail Bolts (104) with Handrail Spacers
(106) into the right Upright (99) and the right Handrail
(83). Be careful not to pinch the wires. Make sure
that the Handrail Spacers are flush against the right
Upright, with the thick sides facing the center of the
treadmill, as shown in the inset drawing. Next, lift the
right Handrail (83) slightly and align the Bolts with the
holes in the Handrail. Thread the Bolts into the
Handrail. Do not tighten the Bolts yet.
5
99
106
Thick
Side
83
Attach the left Handrail (not shown) in the same way.
Then, tighten all four Handrail Bolts (104).
104
106
6. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 29). To protect the
floor or carpet from damage, place a mat under the treadmill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset draw-
ing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE SENSOR TROUBLESHOOTING
Sensor
Unit
Buckle
Sensor Unit
The instructions on the following pages explain
how the chest pulse sensor is used with the con-
sole. If the chest pulse sensor does not function
properly, try the steps below.
Next, wrap the
chest pulse sen-
sor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse sen-
• Make sure that you are wearing the chest pulse sen-
sor as described at the left. Note: If the chest pulse
sensor does not function when positioned as de-
scribed, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
sor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens so-
lution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
• The CR2032 battery may need to be replaced (see
page 30).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the pos-
sibility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing 1 at the right). To purchase a surge sup-
pressor, see your local NordicTrack dealer or call
1-800-806-3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Program
Display
Main
Display
Pulse
Sensor
Pulse
Sensor
Note: If there is a thin sheet
of clear plastic on the face
of the console, remove it.
Clip
Key
FEATURES OF THE CONSOLE
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. To pur-
chase iFIT.com CDs or videocassettes, call toll-
free 1-800-735-0768.
The advanced console offers a selection of features
designed to help you get the most from your exercise.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sen-
sor or the chest pulse sensor.
Sixteen preset workout programs are also offered. Each
program automatically controls the speed and incline
of the treadmill to give you an effective workout. You
can even create custom workout programs and store
them in memory for future use.
With the treadmill connected to your computer, you
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
In addition, the console offers two heart rate programs
that automatically adjust the speed and incline of the
treadmill to keep your heart rate near a target level
while you exercise. Note: The heart rate programs re-
quire the use of the chest pulse sensor.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Move the on/off circuit breaker to the reset po-
sition.
3
4
CAUTION:
Before operating the
console, read the following precautions.
Locate the on/off circuit
breaker near the power
• Do not stand on the walking belt when turn-
ing on the power.
cord. Make sure that the
on/off circuit breaker is in
the on position
Reset
Position
• Always wear the clip (see the drawing below)
while operating the treadmill.
• Adjust the speed in small increments in
order to avoid sudden jumps in speed.
Insert the key fully into the console.
Stand on the foot rails of the treadmill. Attach the
clip securely to the waistband of your clothes.
Next, insert the key into the console. After a
moment, the program display and the main display
will light. Note: When the key is inserted, the
treadmill incline system may automatically
calibrate itself—the treadmill will rise to the highest
incline level and then return to the lowest incline
level. During calibration, the left side of the main
display will show two dashes (– –) and the seg-
ment time indicator will flash.
• The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determin-
ing heart rate trends in general.
• If you have heart problems, or if you are over
60 years of age and have been inactive, do
not use the heart rate programs. If you are
taking medication regularly, consult your
physician to find whether the medication will
affect your exercise hart rate.
Enter your weight.
5
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
Although you can use the console without enter-
ing your weight, the console will count your calorie
expenditure more accurately if you enter your
weight. To enter your weight, press either of the
Age/Weight Set buttons. The words “ENTER
WEIGHT” and the current weight setting will ap-
pear in the main display. Press the Age/Weight
Set buttons again to enter your weight. The but-
tons can be held down to enter your weight
quickly. Your weight will then be saved in memory.
GETTING STARTED
Attach the clip to the waistband of your clothes.
1
Stand on the foot rails
of the treadmill. Find
Clip
the clip attached to the
key and slide the clip
onto the waistband of
your clothes. Next, in-
sert the key into the
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset program,
see page 14. To create and use a custom program,
see pages 16 and 17. To use a heart rate program,
see page 18. To use an iFIT.com CD or video pro-
gram, see page 22. To use an iFIT.com program di-
rectly from our Web site, see page 24.
console. Test the clip by carefully taking a few
steps backward until the key is pulled from the
console. If the key is not pulled from the con-
sole, adjust the position of the clip as needed.
Then, remove the key from the console.
Plug in the power cord.
2
See page 9.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
change by 0.5%. To change the incline quickly,
press the 1-step Incline buttons. The incline range
is 0% to 12%. Note: After the buttons are pressed,
it may take a moment for the treadmill to reach the
selected incline setting.
HOW TO USE THE MANUAL MODE
Insert the key fully into the console.
1
See GETTING STARTED on page 11.
Follow your progress with the LED track, the
Training Zone display, and the main display.
5
Select the manual mode.
2
The LED track—When
the manual mode or the
iFIT.com mode is se-
lected, the program dis-
play will show an LED
track representing 1/4
When the key is inserted, the manual mode will
automatically be selected. If a program has been
selected, press the Select Goal button repeatedly
until the words “MANUAL MODE” appear in the
main display.
mile. As you exercise, the indicators around the
track will light, one at a time, until you have walked
or run 1/4 mile. A new lap will then begin.
The Training Zone display—As you exercise, the
Training Zone display will show the approximate
intensity level of your exercise. For example, if four
to six indicators in the display are lit, your intensity
level is ideal for fat burning.
Press the Start button or the Speed + button to
start the walking belt.
3
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking
belt as desired by
pressing the Speed +
and – buttons. Each
time a button is
pressed, the speed set-
ting will change by 0.1
The main display—The main display will show
the following information:
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. To change
the speed setting quickly, press the 1-step Speed
buttons. The speed range is 0.5 mph to 12 mph.
Note: After the buttons are pressed, it may take a
moment for the treadmill to reach the selected
speed setting.
Incline—The left side of
the main display shows
the incline level of the
treadmill.
Time/Pace—When the
manual mode or the
To stop the walking belt, press the Stop button.
The time will begin to flash in the main display. To
restart the walking belt, press the Start button or
the Speed + button.
iFIT.com mode is se-
lected, the next section
of the main display will
show the elapsed time
and your current pace (pace is measured in min-
utes per mile). The display will change from one
number to the other every few seconds; the Pace
indicator will light when your pace is shown. When
a program is selected, the display will show the
time remaining in the program, your current pace,
and the time remaining in the current segment of
the program.
Note: The first time the treadmill is used, inspect
the alignment of the walking belt, and align the
walking belt if necessary (see page 29).
Change the incline of the treadmill as desired.
4
To change the incline of
the treadmill, press the
Incline
L
and
L
buttons.
Each time a button is
pressed, the incline will
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance/Laps—The
center section of the
main display shows the
distance that you have
walked and the number
of 1/4-mile laps you
Measure your heart rate if desired.
6
You can measure your heart rate using the chest
pulse sensor or the handgrip pulse sensor. To use
the handgrip pulse sensor, follow the instructions
below.
have completed. The display will change from one
number to the other every few seconds; the Laps
indicator will light when the number of laps is
shown.
Stand on the foot
rails and place
Metal Contacts
your hands on the
metal contacts on
the handrail. Your
palms must be rest-
ing on the upper
contacts, and your
fingers must be
Calories/Pulse—
When you are not
using the handgrip
pulse sensor, the next
section of the main dis-
play will show the ap-
touching the lower
contacts—avoid
moving your
hands. When your
pulse is detected,
the Pulse indicator will light and then your heart
rate will be shown in the main display. For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
proximate numbers of calories and fat calories
you have burned (see FAT BURNING on page
31). The display will change from one number to
the other every few seconds; the Fat indicator will
light when the number of fat calories is shown.
When you are using the handgrip pulse sensor,
the display will show your heart rate (see step 6 at
the right).
Speed—The right side
of the main display
shows the speed of the
walking belt.
Turn on the fans if desired.
7
8
To turn on the fans at low speed, press the Fans
button. To turn on the fans at high speed, press
the Fans button a second time. To turn off the
fans, press the Fans buttons a third time. Note:
Any time that the walking belt is stopped for a few
minutes, the fans will automatically turn off.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find
which unit of measure-
ment is selected, hold
When you are finished exercising, stop the
walking belt and remove the key.
down the Stop button while inserting the key into
the console. An “E” for English miles or an “M” for
metric kilometers will appear on the right side of
the main display. Press the Speed + button to
change the unit of measurement. When the de-
sired unit of measurement is selected, remove the
key and then reinsert it. Note: For simplicity, all
instructions in this manual refer to miles.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest level.
The incline must be at the lowest level when
the treadmill is raised to the storage position or
the treadmill will be damaged. Next, remove the
key from the console and put it in a secure place.
Note: If the displays and indicators on the con-
sole remain lit after the key is removed, the
console is in the “demo” mode. See page 25
and turn off the demo mode.
To reset the main display, press the Stop button,
remove the key, and then reinsert the key.
When you are finished using the treadmill, move
the on/off circuit breaker near the power cord to
the off position and unplug the power cord.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the Start button or the Speed + button to
start the program.
HOW TO USE PRESET PROGRAMS
3
Insert the key fully into the console.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
1
See GETTING STARTED on page 11.
Select the desired preset program.
2
Each program is divided into several time seg-
ments of different lengths. (The main display
shows both the time remaining in the program and
the time remaining in the current segment of the
program.) One speed setting and one incline set-
ting are programmed for each segment. (The
same speed setting and/or incline setting may be
programmed for consecutive segments.) The
speed setting for
The console offers sixteen preset programs—four
programs that focus on weight loss, seven pro-
grams designed for aerobic exercise, and five pro-
grams for high-performance conditioning.
When the key is inserted, the manual mode will be
selected. To select one of the preset programs,
first press the Select Goal button repeatedly until
the words “WEIGHT LOSS,” “AEROBIC,” or
“PERFORMANCE” appear in the main display.
the first segment is
Current Segment
shown in the flash-
ing Current
Segment column of
the program dis-
play. (The incline
settings are not
shown in the program display.) The speed set-
tings for the next several segments are shown in
the columns to the right.
Next, press the Select Course button repeatedly
to select one of the weight loss, aerobic, or perfor-
mance programs. For example, if the words
“WEIGHT LOSS” appear in the main display, you
can select the 20-minute Pyramid, 35-minute
Pyramid, 20-minute Fat Burn, or 20-minute
Interval program.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, if the speed
and/or incline of the treadmill is about to change,
the speed setting and/or incline setting will flash in
the main display to alert you. When the first seg-
ment is completed, all speed settings will move
one column to the left. The speed setting for the
second segment will then be shown in the flashing
Current Segment column and the treadmill will au-
tomatically adjust to the speed and incline settings
for the second segment. Note: If all of the indica-
tors in the Current Segment column are lit after the
speed settings have moved to the left, the speed
settings will move downward so that only the high-
est indicators appear in the program display. If
some of the indicators in the Current Segment col-
umn are not lit when the speed settings move to
the left again, the speed settings will move back
up.
Three seconds after a preset program is selected,
the name of the selected program, the maximum
speed setting for the program, the maximum in-
cline setting for the program, and the total program
time will begin to scroll across the main display.
The program dis-
play will show the
speed settings of
the program you
have selected.
Note: If you have
selected a program with more than seventeen
segments, the display will show only the first sev-
enteen speed settings.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then slow to a
stop.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline setting is too high or too low
during the program, you can manually override
the setting by pressing the Speed or Incline but-
tons on the console. Every few times one of the
Speed buttons is pressed, an additional indicator
will light or darken in the Current Segment column.
(If any of the columns to the right of the Current
Segment column have the same number of lit indi-
cators as the Current Segment column, an addi-
tional indicator may light or darken in those
columns as well.) Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. Note: If you manually override
the speed or incline setting, when the next seg-
ment begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
Follow your progress with the displays.
See step 5 on page 12.
4
5
6
7
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the fans if desired.
See step 7 on page 13.
When the program has ended, remove the key.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at the lowest level. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re-
moved, the console is in the “demo” mode.
See page 25 and turn off the demo mode.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the main dis-
play. To restart the program, press the Start button
or the Speed + button. The walking belt will begin
to move at 1 mph. When the next segment begins,
the treadmill will automatically adjust to the speed
and incline settings for the next segment. To end
the program, press the Stop button, remove the
key, and then reinsert the key.
When you are finished using the treadmill, move
the on/off circuit breaker near the power cord to
the off position and unplug the power cord.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Refer to the program display. Each custom pro-
gram is divided into one-minute segments. One
speed setting and one incline setting can be pro-
grammed for each segment. The speed setting for
the first segment
HOW TO CREATE CUSTOM PROGRAMS
Insert the key fully into the console.
1
will be shown in the
See GETTING STARTED on page 11.
Current Segment
flashing Current
Segment column of
the program dis-
play. (The incline
settings are not
Select one of the custom programs.
2
When the key is inserted, the manual mode will be
selected. To select a custom program, first press
the Select Goal button repeatedly until the words
“CUSTOM PROGRAM” appear in the main dis-
play.
shown in the pro-
gram display.) To program a speed setting and an
incline setting for the first segment, simply adjust
the speed and incline of the treadmill as desired
by pressing the Speed and Incline buttons. Every
few times one of the Speed buttons is pressed, an
additional indicator will light or darken in the
Current Segment column.
When the first segment of the program is com-
pleted, the current speed setting and the current
incline setting will be stored in memory. The three
columns of indicators will then move one column
to the left, and the speed setting for the second
segment will be shown in the flashing Current
Segment column. Program a speed setting and an
incline setting for the second segment as de-
scribed above.
Next, press the Select Course button repeatedly to
select the Learn 1 or Learn 2 program.
Three seconds after a custom program is selected,
the name of the selected program and the total
program time will begin to scroll across the main
display.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Note: If the custom program has not yet been
defined, one to three columns of indicators
will be lit in the program display. If more than
three columns of indicators are lit, see HOW
TO USE CUSTOM PROGRAMS on page 17.
When the program has ended, remove the key.
4
Press the Start button or the Speed + button
See step 7 on page 15.
3
and program the desired speed and incline
settings.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, the speed setting and the
incline setting will flash in the main display, and all
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
HOW TO USE CUSTOM PROGRAMS
Insert the key fully into the console.
1
See GETTING STARTED on page 11.
Select one of the custom programs.
2
When the key is inserted, the manual mode will be
selected. To select a custom program, first press
the Select Goal button repeatedly until the words
“CUSTOM PROGRAM” appear in the main dis-
play. Next, press the Select Course button repeat-
edly to select the Learn 1 or Learn 2 program.
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and no time remains in the pro-
gram. The walking belt will then slow to a stop.
Three seconds after a custom program is se-
lected, the name of the selected program and the
total program time will begin to scroll across the
main display.
If desired, you can redefine to the program while
using it. To change the speed or incline setting
during the current segment, simply press the
Speed or Incline buttons. When the current segment
is completed, the new setting will be saved in mem-
ory. To increase the length of the program, first
wait until the program is completed. Then, press the
Start button, and program speed and incline settings
for as many additional segments as desired. When
you have added as many segments as desired,
press the Stop button twice. To decrease the
length of the program, press the Stop button twice
at any time before the program is completed.
The program display will show the first speed set-
tings of the program you have selected (see the
drawing below). Note: If only three columns of
indicators are lit in the program display, see
HOW TO CREATE A CUSTOM PROGRAM on
page 16.
Press the Start button or the Speed + button to
start the program.
3
To stop the program temporarily, press the Stop
button. The time will begin to flash in the main dis-
play. To restart the program, press the Start but-
ton or the Speed + button. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each program is divided into several one-minute
segments. (The main display shows both the time
remaining in the program and the time remaining
in the current segment of the program.) One
speed setting and one incline setting are pro-
grammed for each segment. The speed setting for
the first segment is shown in the flashing Current
Segment column
Follow your progress with the displays.
See step 5 on page 12.
4
5
When the program has ended, remove the key.
See step 7 on page 15.
of the program
display. (The in-
Current Segment
cline settings are
not shown in the
program display.)
The speed set-
tings for the next
several segments will be shown in the columns to
the right.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
During heart rate
programs, the pro-
gram display will
HOW TO USE HEART RATE PROGRAMS
Heart rate programs automatically adjust the speed
and incline of the treadmill to keep your heart rate near
a target level while you exercise. Note: You must
wear the chest pulse sensor to use heart rate pro-
grams.
show a graphic that
represents your
heart rate. Each
time a heartbeat is detected, an additional peak
will appear.
Enter your age and a maximum speed setting.
4
CAUTION:
If you have heart prob-
Three seconds after a heart rate program is se-
lected, the words “ENTER AGE” and the current
age setting will appear in the main display. You
must enter your age to use a heart rate program.
If you have already entered your age, press the
Start button (pressing the button will not start the
program at this time). If you have not entered your
age, press the Age/Weight Set buttons to enter
your age. The buttons can be held down to enter
your age quickly. Then, press the Start button.
Once you have entered your age, it will be saved
in memory.
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether
the medication will affect your exercise heart
rate.
Follow the steps below to use a heart rate program.
Put on the chest pulse sensor.
1
See the instructions on page 8.
Insert the key fully into the console.
2
See GETTING STARTED on page 11.
Select a heart rate program.
After you have entered your age, the words
“ENTER MAX SPEED” and the maximum speed
setting of the program will appear in the main dis-
play. If desired, press the Speed buttons or the
1-step Speed buttons to change the maximum
speed setting.
3
When the key is inserted, the manual mode will be
selected. To select a heart rate program, first
press the Select Goal button repeatedly until the
words “HEART RATE” appear in the main display.
Next, press the Select Course button until the words
“PULSE DRIVEN 1” or “PULSE DRIVEN 2” appear.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline setting is too high or too low
during the program, you can adjust the setting
with the Speed or Incline buttons. However, each
time the console compares your heart rate to the
current target heart rate setting, the speed and/or
incline of the treadmill may automatically change
to bring your heart rate closer to the target heart
rate setting.
Press the Start button or the Speed + button to
start the program.
5
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each heart rate program is divided into several time
segments of different lengths. (The main display
shows both the time remaining in the program and
the time remaining in the current segment of the
program.) One target heart rate setting is pro-
grammed for each segment.
If your pulse is not detected during the program,
the letters “PLS” will flash in the main display and
the speed and incline of the treadmill may auto-
matically decrease until your pulse is detected. If
this occurs, see page 8.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
During each segment, the console will regularly
compare your heart rate to the current target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting, the speed of
the treadmill will automatically increase or de-
crease to bring your heart rate closer to the target
heart rate setting. If the speed reaches the maxi-
mum speed setting of the program (see step 4 on
page 17) and your heart rate is still too far below
the current target heart rate setting, the incline of
the treadmill will also increase to bring your heart
rate closer to the target heart rate setting.
Follow your progress with the displays.
See step 5 on page 12.
6
7
8
Turn on the fans if desired.
See step 6 on page 13.
During the last three seconds of each segment, a
series of tones will sound and the speed setting
and/or the incline setting will flash in the main
display.
When the program has ended, remove the key.
See step 7 on page 15.
The program will continue until no time remains in
the program. The walking belt will then slow to a
stop.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be connected
to your portable CD player, portable stereo, home
stereo, or computer with CD player. See this page and
page 21 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 22 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home com-
puter. See page 21 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Adapter
Audio
Cable
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
LINE OUT
Audio
Cable
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
PHONES
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 21.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
20. Note: To purchase iFIT.com CDs or videocas-
settes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
Insert the key fully into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
See GETTING STARTED on page 11.
AUDIO OUT
RIGHT
LEFT
Select the iFIT.com mode.
2
Adapter
Audio
Cable
When the key is in-
serted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the iFIT.com button. The
indicator above the button will light and the words
“IFIT MODE” will appear in the main display.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the PLAY button on your CD player or
VCR.
B
4
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the time is flashing in the
main display, press the Start button or the Speed
+ button on the console. The treadmill will not re-
spond to a CD or video program while the time is
flashing.
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the main display. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move.
When the next “chirp” is heard, the speed and
incline will change to the next settings of the
CD or video program.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the displays.
See step 5 on page 12.
5
6
7
8
Measure your heart rate if desired.
See step 6 on page 13.
When the CD or video program is completed, the
walking belt will stop and the time will begin to flash
in the main display. Note: To use another CD or
video program, press the Stop button or remove
the key and go to step 1 on page 22.
Turn on the fans if desired.
See step 7 on page 13.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
When the program is completed, remove the
key.
• Make sure that the iFIT.com indicator is lit and
that the time is not flashing in the main dis-
play. If the time is flashing, press the Start
button or the Speed + button on the console.
See step 7 on page 15.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 21. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements is found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
Insert the key fully into the console.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the main display. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the speed
and incline will change to the next settings of
the program.
1
See GETTING STARTED on page 11.
Select the iFIT.com mode.
2
When the key is in-
serted, the manual
mode will be selected.
To use a program from
our Web site, press the
iFIT.com button. The in-
dicator above the button will light and the words
“IFIT MODE” will appear in the main display.
When the program is completed, the walking belt
will stop and the time will begin to flash in the time
display. Note: To use another program, press the
Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time display is not flashing. In addition,
make sure that the audio cable is properly con-
nected, that it is fully plugged in, and that it is
not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Start your web browser, if necessary, and go to
4
Follow the desired links on our Web site to se-
lect a program.
5
When the program has ended, remove the key.
8
Read and follow the on-line instructions for using a
program.
See step 7 on page 15.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
An “E” for English miles or
an “M” for metric kilometers
will appear on the right side
of the main display. Press
the Speed + button to
change the unit of measure-
ment.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
IMPORTANT: Make sure
that there is not a letter
“D” in the main display. If
a “D” appears in the display,
the console is in the “demo”
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the main display will
show the following information:
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “D” ap-
pears in the display when the information mode is
selected, press the Speed – button so that it disap-
pears.
The left side of the main
display will show the total
number of hours that the
treadmill has been used.
The center of the main
display will show the total
number of miles that the
walking belt has moved.
To exit the information mode, remove the key from the
console.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Remove the key and unplug the power
cord. CAUTION: You must be able to safely lift 45 pounds
(20 kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Pull the latch knob to the left and hold it.
Raise the treadmill until the platform passes the pin on
the latch knob. Release the latch knob. Make sure that
the platform is resting against the pin as shown.
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Latch
Knob
Platform
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the plat-
form is resting against the pin on the latch knob.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location.
Never move the treadmill without tipping it back. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
Base
Front Wheels
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Pull the latch knob to the left and hold it. Pivot
the treadmill down until the platform is past the pin on the
latch knob. Slowly release the latch knob.
Pin
Latch
Knob
Platform
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame to
the floor. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the on/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the on/off circuit breaker has
tripped. To reset the on/off circuit breaker, wait for
five minutes and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off circuit breaker is in the reset position.
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
a
48
power cord. Remove the indicated Screws (48) from
62
the Hood (62). Carefully rotate and lift the Hood.
48
Locate the Reed Switch (37) and the Magnet (31) on
the left side of the Pulley (30). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(93) and move the Reed Switch slightly. Retighten the
Screw. Re-attach the hood, and run the treadmill for a
few minutes to check for a correct speed reading.
1/8”
93
30
31
37
Top
View
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
3”–4”
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key and
a
UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the bolt counterclockwise
1/2 of a turn. Be careful not to overtighten the walking belt.
Plug in the power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is cen-
tered.
b. If the walking belt slips when walked on, first remove the
b
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key, and care-
fully walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
PROBLEM: The treadmill rocks during use
SOLUTION: a. If the treadmill rocks slightly during use, turn one or
a
both of the Leveling Feet (127) under the Upright (99)
until the the rocking motion is eliminated. Note: If nec-
essary, tip the treadmill forward and use a phillips
screwdriver to turn the Leveling Feet.
127
99
127
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CDs and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The heart rate monitor does not function properly
SOLUTION: a. If the heart rate monitor does not function properly, see CHEST PULSE SENSOR TROUBLE-
SHOOTING on page 8.
b. If the heart rate monitor still does not function properly, the battery
b
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Battery Cover
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Cover
Battery
Rubber
Gasket
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
pulse sensor on the console.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
32
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
33
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTL25530
R0703A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
2
1
2
2
2
4
8
1
1
1
8
14
1
1
2
1
2
1
2
2
1
1
1
1
1
1
2
1
1
1
1
1
2
2
1
1
1
1
1
1
6
2
1
1
1
1
32
5
1
2
Allen Wrench
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
4
1
2
1
1
1
1
1
1
2
1
4
15
4
1
1
1
3
7
1
6
3
2
1
1
2
2
2
Incline Motor Bracket
Front Roller Adj. Bolt
Front Roller Nut
Motor Bolt
Pulse Wire
Lift Leg
Left Fan Housing
Large Cage Nut
Power Supply Bracket
Front Endcap (Right)
Motor Hood
Rear Wheel Bolt
Rear Endcap (Left)
Roller Star Washer
Rear Roller Adj. Bolt
Rear Wheel
U-nut
Endcap Bolt
9
Roller Guard (Left)
Roller Guard (Right)
Rear Endcap (Right)
Endcap Nut
Foot Rail Washer
Rear Roller
Warning Decal
Foot Rail Cover
Pulse Receiver
Belt Guide
Chest Pulse Sensor
Frame Pivot Bolt
Frame Pivot Washer
Left Foot Rail
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38*
39
40
41
42
43
44
45
46
47
48
49
50
51
Hood Clip
Controller
Controller Bracket
Motor Controller Wire
Power Cord
Power Cord Grommet
Belly Pan Plug
12” Audio Wire
Audio Wire Nut
On/Off Switch
Static Decal
Walking Belt
Belly Pan
Tie Holder
Walking Platform
Right Foot Rail
Front Endcap (Left)
Ground Wire
Support Bracket Screw
Support Bracket
Front Roller/Pulley
Magnet
Belly Pan Bracket
Support Bracket Screw
Filter Wire
Console Ground Wire
Console Base
Console
Book Holder
Handrail
Motor Belt
Motor
Handrail Endcap
Hand Grip Pulse
Grip Pulse Screw
Console Screw
2” Console Screw
Console Back
Base Plate Edging
Base Plate
Base Plate Screw
Base Screw
Wire Track
Base Pad
Cage Nut
Upright Endcap
Key/Clip
Upright
Front Wheel Bolt
Front Wheel Bushing
Front Wheel
Frame Pivot Bushing
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
Idler Assembly
Idler Pulley Bolt
Pulley Bushing
Idler Pulley
Lift Motor Nut/Idler Nut
Tension Washer
Tension Bolt
Idler Arm Bearing
Idler Arm
Idler Spring
Hood Mount Screw
Hood Mount
Incline Motor
Incline Motor Bolt
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
103
104
105
106
107
108
109
110
111
112
113
114*
115
116
117
118
119
120
121
2
4
2
4
1
1
1
1
1
1
1
1
1
1
1
2
2
2
4
Front Wheel Spacer
Handrail Bolt
Fan
Handrail Bushing
Latch Pin
Pin Clip
Latch Pin Collar
Latch Knob Spring
Latch Knob Sleeve
Latch Knob Spacer
Latch Knob
Latch Assembly
Left Cup Holder
Right Cup Holder
Right Fan Housing
Upright Endcap (Round)
Wire Harness
122
123
124
125
126
127
128
129
130
131
132
#
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
iFIT.com Audio Cable
Jack
Releaseable Tie
Catch
Idler Arm Bushing
Leveling Foot
Endcap Spring
Chest Pulse Strap
Console Base
Roller Adj. Washer
Transformer
12” Green Wire, 2/Ring
4” Green Wire, F/Ring
8” Blue Wire, 2F
4” Blue Wire, 2F
User's Manual
#
#
#
#
Hood Mount (Side)
8” Cable Tie
* Includes all parts shown in the box
# These parts are not illustrated
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER OF THE PRODUCT (NTL25530)
• The NAME OF THE PRODUCT (NordicTrack® 7200 R treadmill)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 34 and 35 and the
EXPLODED DRAWING attached in the center of this manual)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL25530
R0703A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL25530
R0703A
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® 7200 R treadmill (“Product”) is warranted to be free of all defects in ma-
terial and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the motor for three years after the date
of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical components are
covered for two years after the date of purchase. All electrical components are covered for two years after the date of
purchase. Labor is covered for one year. The hood, covers, belly pan, and decals are covered for six months after the
date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes or to products used as store display modules.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-
ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-
ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-
vice is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-
itation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 200087 R0703A
Printed in USA © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|