Model No. NTEL08990
Serial No.
USERÕS MANUAL
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical crosstrainer.
1. Read all instructions in this manual before
using the elliptical crosstrainer.
11. Keep your back straight when using the ellip-
tical crosstrainer. Do not arch your back.
2. It is the responsibility of the owner to ensure
that all users of the elliptical crosstrainer
are adequately informed of all precautions.
12. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
3. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrain-
er indoors, away from moisture and dust.
13. The elliptical crosstrainer is intended for
in-home use only. Do not use the elliptical
crosstrainer in a commercial, rental, or insti-
tutional setting.
4. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
14. After adjusting the incline frame, move it up
or down slightly until the pin on the incline
knob snaps into one of the four holes in the
incline bracket. Push the incline knob to
make sure that the pin is fully inserted into
the hole.
5. Keep children under age 12 and pets away
from the elliptical crosstrainer at all times.
6. The elliptical crosstrainer should not be used
by persons weighing more than 250 pounds.
15. The decal shown below has been placed on
the elliptical crosstrainer. If the decal is
missing or illegible, please call our Customer
Service Department toll-free at 1-888-825-
2588 to order a free replacement decal.
Apply the decal in the location shown.
7. Always hold the handlebar or the upper
body arms when mounting, dismounting, or
using the elliptical crosstrainer.
8. Wear appropriate exercise clothing when
using the elliptical crosstrainer. Always wear
athletic shoes for foot protection.
9. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
10. When you stop exercising, allow the pedals
to slowly come to a stop.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the new NordicTrack¨
VGR940 elliptical crosstrainer. The NordicTrack¨
VGR940 is an incredibly smooth exerciser that moves
your feet in a natural elliptical path, minimizing the
impact on your knees and ankles. And the unique
NordicTrack¨ VGR940 features adjustable resistance
and incline to help you get the most from your exercise.
Welcome to a whole new world of natural, elliptical-
motion exercise from NordicTrack.
tional questions, please call our Customer Service
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is NTEL08990. The
serial number can be found on a decal attached to the
elliptical crosstrainer (see the front cover of this man-
ual for the location of the decal).
For your benefit, read this manual carefully before
you use the NordicTrack¨ VGR940. If you have addi-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Water Bottle Holder*
Upper Body Arm
Book Rack
Console
Handlebar
FRONT
Incline Frame
Incline Knob
BACK
Pedal Disk
RIGHT SIDE
Pedal Arm
*No water bottle is included
Wheel
Pedal
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the two
included allen wrenches, assembly requires a phillips screwdriver
wrench , and a rubber mallet
, an adjustable
.
As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on
page 18. The second number refers to the quantity used in assembly. Note: Some small parts may have been
pre-assembled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.
M8 Split
Washer (58)Ð2
M8 Washer (33)Ð2
M10 Nylon Locknut (26)Ð6
Chrome Tube
Washer (84)Ð2
Plastic Pedal
Spacer (85)Ð2
Front Stabilizer Bolt (86)Ð2
Pedal Screw (43)Ð6
Rear Stabilizer Bolt (60)Ð2
Incline Axle Screw (30)Ð2
1. Identify the Rear Stabilizer (59), which has Wheels (45)
attached to it.
1
59
26
Attach the Rear Stabilizer (59) to the rear of the Frame
(1) with the two Rear Stabilizer Bolts (60) and two M10
Nylon Locknuts (26). Make sure that the Rear
Stabilizer is turned so the Wheels are not touching
the floor.
26
45
1
60
2. Attach the Front Stabilizer (14) to the front of the
Frame (1) with the two Front Stabilizer Bolts (86) and
two M10 Nylon Locknuts (26).
2
14
86
26
1
26
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide an M8 Split Washer (58) and an M8 Washer (33)
onto an Incline Axle Screw (30). Tighten the Incline
Axle Screw into one end of the Incline Axle (29). Next,
apply a small amount of the included grease to the
Incline Axle.
3
V-shaped Groove
5
Align the indicated tubes on the Incline Frame (5) with
the tubes on the Base (1). Make sure that the Incline
Frame is turned so the V-shaped grooves are on
top. Insert the Incline Axle (29) through the Incline
Frame and the Base. Note: It may be helpful to tap the
Incline Axle with a rubber mallet to insert it.
58
33
30
29
Grease
33
Tubes
Slide an M8 Split Washer (58) and an M8 Washer (33)
onto the other Incline Axle Screw (30). Tighten the
Incline Axle Screw into the open end of the Incline Axle
(29).
58
1
30
Tubes
4. Remove the four Console Screws (35) and the four
Console Washers (44) from the Console (87).
4
87
Connect the console wire to the Harness Extension
(51).
Attach the Console (87) to the Upright (2) with the four
Console Screws (35) and the four Console Washers
(44) removed previously. Be careful to avoid pinching
the wires.
Console
Wire
51
44
2
35
2
35
5. Remove the four M10 Nylon Locknuts (not shown)
from the welded bolts on the front of the Frame (1).
5
Lay a cloth over the front of the Frame (1) to protect it
from scratches. Lay the Upright (2) in the position
shown. Connect the Harness Extension (51) to the
Wire Harness (25).
51
25
Welded Bolts
1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Align the two holes in the front of the Upright (2) with
the two welded bolts on the front of the Frame (1).
6
2
Next, pivot the Upright (2) about halfway to a vertical
position. Refer to the inset drawing. As you raise
the Upright, look into the lower end and make sure
that the Harness Extension (51) and the Wire
Harness (25) do not get pinched between the
Upright (2) and the Frame (1). In addition, feed the
slack in the Harness Extension and the Wire
Harness into the Upright. Continue to raise the
Upright until the four welded bolts are inserted through
the bracket at the bottom of the Upright.
26
5
1
Welded Bolts
Lift the front of the Incline Frame (5). Tighten an M10
Nylon Locknut (26) onto each welded bolt.
2
51
25
1
7. Identify the Left Pedal Arm (3), which has an ÒLÓ sticker
on it. Next, identify the Left Pedal (41), which has the
letter ÒLÓ molded onto the bottom.
7
43
Welded
Bolt
Turn over the Left Pedal Arm (3) as shown. Insert the
three plastic posts on the Left Pedal (41) into the three
indicated holes in the Left Pedal Arm. Make sure that
the Left Pedal is turned as shown. Attach the Left
Pedal with three Pedal Screws (43).
3
Open Side
Plastic Posts
Attach the Right Pedal (not shown) to the Right Pedal
Arm (not shown) in the same way.
41
8. Apply a small amount of grease to the axle on the left
Crank Arm (6).
8
Side a Plastic Pedal Spacer (85) and the Left Pedal
Arm (3) onto the axle on the left Crank Arm (6). Note: It
may be helpful to use a rubber mallet to tap these parts
on. Be careful not to confuse the Left Pedal Arm
with the Right Pedal Arm (not shown); look at the
position of the round tube to identify the Left Pedal
Arm. Next, tap a 3/4Ó Axle Cap (61) onto the axle.
Grease
6
3
85
Attach the Right Pedal Arm (not shown) in the same way.
Round
Tube
61
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Apply grease to the welded bolt on the Left Pedal Arm
(3). Slide a Chrome Tube (21) and a Chrome Tube
Washer (84) onto the welded bolt. Make sure that the
Chrome Tube is turned exactly as shown in the
inset drawing. Then, tighten an M10 Nylon Locknut
(26) onto the welded bolt.
9
Wide
Side
Narrow
Side
4
Lubricate
26 84
21
3
21
Attach the other Chrome Tube (not shown) to the Right
Pedal Arm (4) in the same way.
Grease
3
Apply a small amount of the included Teflon¨ lubricant
to a paper towel. Rub a thin film of the lubricant onto
both Chrome Tubes (21).
84
26
Welded Bolt
10.Slide the Left Upper Body Arm (7), which is marked
with an ÒLÓ sticker, onto the Chrome Tube (21) on the
Left Pedal Arm (3). Slide the Right Upper Body Arm
(75) onto the Chrome Tube on the Right Pedal Arm (4).
Make sure that the Upper Body Arms are on the
correct sidesÑthe upper ends should bend in the
direction shown by the arrows. Next, slide an Axle
Cover (74) onto the post on each Upper Body Arm.
10
75
74
34
19
Apply grease to the Arm Axle (19). Insert the Arm Axle
into the Upright (2), the right Pivot Cover (74), and the
Right Upper Body Arm (75) as shown. Push the Arm
Axle into the Upright until the left end of the Axle is flush
with the left side of the Upright. Next, raise the Left
Upper Body Arm (7) and insert the Arm Axle into the
left Axle Cover (74) and the Left Upper Body Arm.
Center the Arm Axle.
74
15
7
2
Grease
Post
15
21
4
34
Using the included pedal tool, tap two Push Nuts (15)
about 1/8Ó onto each end of the Arm Axle (19). Make
sure that the Push Nuts are turned as shown in the
inset drawing. Note: It may be helpful if another person
holds a block of wood against one end of the Arm Axle
while you tap Push Nuts onto the other end.
21
Pedal Tool 15 19
Press the two Axle Caps (34) onto the Arm Axle (19).
3
11. Plug the Power Supply (78) into the jack at the rear of
the elliptical crosstrainer. Note: Your Power Supply
may look different from the one pictured.
11
Jack
78
12. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware
may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat
under the elliptical crosstrainer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL CROSSTRAINER
INCLINE ADJUSTMENT
EXERCISING ON THE ELLIPTICAL CROSSTRAINER
As you exercise on the elliptical crosstrainer, you can
vary the effect of the exercise by raising or lowering
the incline frame. First, position the pedal arms side
by side as shown. Next, lift the incline frame slightly
and pull the incline knob. Raise or lower the incline
frame to the desired position and release the incline
knob. Move the incline frame up or down slightly
until the pin on the incline knob snaps into one of
the four holes in the incline bracket. Push the
incline knob to make sure that the pin is fully
inserted into the hole.
To mount the elliptical crosstrainer, hold the handlebar
and step onto the pedal that is in the lowest position.
Next, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The pedal disks can turn in either direction. It is
recommended that you move the pedal disks in
the direction shown by the arrow below; however,
to give variety to your exercise, you may turn the
pedal disks in the opposite direction.
Handlebar
Incline
Bracket
Incline
Frame
Pedal Disk
Incline
Knob
HOW TO PLUG IN THE POWER SUPPLY
Pedal
Make sure that the power supply is plugged into the
elliptical crosstrainer (see step 11 on page 8). Next,
plug the power supply into an electrical outlet.
To dismount the elliptical crosstrainer, wait until the
pedals come to a complete stop. Note: The elliptical
crosstrainer does not have a freewheel; the ped-
als will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
Note: Each time the
power supply is
plugged in, the ellip-
tical crosstrainer will
automatically
calibrate itself.
HOW TO USE THE UPPER BODY ARMS
Calibration will take
less than one
minute. During cali-
bration, the letters ÒCALÓ will appear in the left LED
display and the indicators in the TRAINING ZONE
display will light in a rapid sequence.
The upper body
arms are
Upper Body Arms
designed to add
upper-body exer-
cise to your work-
outs. Move the
upper-body arms
forward and back
as you exercise in
order to work your
arms, back, and
shoulders.
Handlebar
To exercise only your lower body, hold the handlebar
as you exercise.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF THE CONSOLE
HOW TO USE THE MANUAL MODE
Make sure that the power supply is plugged in.
1
Refer to page 9.
Press any button on the console or move the
pedals to turn on the power.
2
When one of the buttons on the console is
pressed or the pedals are moved, various displays
and indicators will light and the left LED display
will begin to flash. Note: If the power supply was
just plugged in, the power will already be on.
Select the manual mode.
3
When the power is
turned on, the
manual mode will
Manual
be selected and
Indicator
the manual indica-
tor will light. If you
have selected a
preset program or the iFit.com mode, press the
SELECT WORKOUT button repeatedly to select
the manual mode.
The advanced console offers a variety of features to
help you get the most from your workouts. When the
manual mode of the console is selected, the resistance
of the pedals can be changed with a touch of a button.
As you exercise, the program display, the training zone
display, and the two LED displays will provide continu-
ous exercise feedback. You can even measure your
heart rate using the built-in pulse sensor.
Begin exercising and adjust the resistance of
the pedals as desired.
4
As you exercise,
change the resis-
tance of the pedals
by pressing the
RESISTANCE but-
tons. There are ten
resistance levels;
level 1 is the easiest. Note: After a RESISTANCE
button is pressed, it will take a moment for the
pedals to reach the selected resistance level.
In addition, the console offers five preset workout pro-
grams. Each program automatically controls the resis-
tance of the pedals as it guides you through an effec-
tive workout.
The console also features revolutionary iFit.com tech-
nology. This technology allows the console to play
specially-designed CD's (available separately) that
automatically control the resistance of the pedals as a
personal trainer coaches you through every step of
your workout. High-energy music provides added
motivation. Each CD features two workout programs
designed by AFAª-certified personal trainers. For
information about iFit.com CDÕs, call toll-free 1-800-
Watch your progress with the program display,
the training zone display, and the LED displays.
5
The program
displayÑWhen
the manual mode
or the iFit.com
mode is selected,
the program dis-
play will show a
track representing 1/4 mile. As you exercise, the
indicators around the track will flash to indicate
your position on the track.
Note: The console can display speed and distance
in either miles or kilometers. To select the desired
unit of measurement, refer to the instructions at
the top of page 16.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The training zone
displayÑAs you
exercise, the train-
ing zone display
must be resting on the upper contacts and your
fingers must be touching the lower contacts.
Avoid moving your hands.
will show the
approximate inten-
When your pulse is
detected, the heart
sity level of your exercise. For example, if three or
four indicators in the display are lit (refer to the
drawing above), the display shows that your inten-
sity level is ideal for fat burning.
rate indicator above
the right LED dis-
play will light, one
to three dashes will
appear in the dis-
The left LED dis-
playÑAs you
exercise, the left
display will show
the elapsed time,
your current
speed, and the
play, and then your heart rate will be shown. For
the most accurate heart rate reading, continue to
hold the contacts for about 15 seconds. Note: If
your heart rate is not shown, make sure that your
hands are positioned as described above. Be
careful not to move your hands excessively or
squeeze the metal contacts too tightly.
current resistance level. The display will change
from one number to the next every six seconds,
as shown by the indicators around the display.
Note: When a preset program is selected, the left
display will show the time remaining in the pro-
gram rather than the elapsed time.
Note: When you hold the pulse sensor, the right
LED display will show your heart rate for up to
two minutes. If you continue to hold the pulse
sensor, the display will show your heart rate along
with the number of calories you have burned and
the distance you have traveled.
The right LED
displayÑAs you
exercise, the right
display will show
the approximate
number of calories
you have burned
and the distance you have traveled. The display
will change from one number to the other every
six seconds, as shown by the indicators around
the display. This display will also show your heart
rate when the pulse sensor is used (see step 6).
WARNING:
The pulse sen-
sor is not a medical device. Various fac-
tors, including the user's movement,
may affect the accuracy of heart rate
readings. The pulse sensor is intended
only as an exercise aid in determining
heart rate trends in general.
When you are finished exercising, turn off the
power.
Note: If you stop exercising for six seconds or
longer, the console will pause and the left LED
display will begin to flash.
7
To turn off the power, simply wait for about ten
minutes. The console has an Òauto-offÓ feature.
If the console buttons are not pressed and the
pedals are not moved for ten minutes, the
console will turn off automatically.
Measure your heart rate, if desired.
6
Note: Before using the pulse sensor, peel the
protective vinyl off the metal contacts on the
top and bottom of the pulse sensor.
Note: If the displays and indicators remain lit
after ten minutes, the console may be in the
ÒdemoÓ mode. Refer to the instructions on
page 16 to turn off the demo mode.
To measure
your heart
rate, place
your hands on
the metal con-
tacts on the
pulse sensor.
Contacts
Your palms
Metal
11
Download from Www.Somanuals.com. All Manuals Search And Download.
four minutes long.
One resistance set-
ting is programmed
for each segment.
The resistance set-
ting for the first
HOW TO USE A PRESET PROGRAM
Current Segment
Make sure that the power supply is plugged in.
1
Refer to page 9.
segment will be
shown in the flash-
ing Current Segment column of the program dis-
play. The resistance settings for the next four seg-
ments will be shown in the segments to the right.
Press any button on the console or move the
pedals to turn on the power.
2
When one of the buttons on the console is
pressed or the pedals are moved, various displays
and indicators will light and the left LED display
will begin to flash. Note: If the power supply was
just plugged in, the power will already be on.
When only three seconds remain in the first seg-
ment, both the Current Segment column and the
column to the right will flash, a series of tones will
sound, and all resistance settings will move one
column to the left. The resistance setting for the
second segment will then be shown in the flash-
ing Current Segment column and the resistance
of the pedals will automatically adjust to the sec-
ond setting. The program will continue in this way
until the resistance setting for the last segment is
shown in the Current Segment column and the
last segment ends.
Select one of the five preset programs.
3
When the power is
turned on, the
Program Indicator
manual mode will
be selected and
the manual indica-
tor will light. To
select a preset
program, press
the SELECT WORKOUT button repeatedly until
one of the five program indicators lights.
Note: You can manually override the resistance
setting for the current segment, if desired, by
pressing the RESISTANCE buttons. However,
when the next segment begins, the resistance
of the pedals will automatically adjust to the
setting for the next segment.
The graphs below show how the resistance will
change during the five preset programs. During
the Gorge Trail program, for example, the resis-
tance will gradually increase during the first half
of the program and then gradually decrease. Note:
When a program is selected, the program display
will show a simplified graph of the program.
Note: If you stop exercising for six seconds or
longer, the program will pause and the left LED
display will begin to flash. To restart the program,
simply resume exercising.
Watch your progress with the training zone
display and the LED displays.
5
Refer to step 5 on pages 10 and 11.
Measure your heart rate, if desired.
Refer to step 6 on page 11.
6
7
When the program is finished, turn off the
power.
To turn off the power, simply wait for about ten
minutes. The console has an Òauto-offÓ feature.
If the console buttons are not pressed and the
pedals are not moved for ten minutes, the
console will turn off automatically.
Press the START PROGRAM button and begin
exercising.
4
Note: If the displays and indicators remain lit
after ten minutes, the console may be in the
ÒdemoÓ mode. Refer to the instructions on
page 16 to turn off the demo mode.
Each program is divided into several individual
segments. Each segment is one, two, three, or
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT YOUR CD PLAYER TO THE
ELLIPTICAL CROSSTRAINER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFit.com CDÕs (available separately), the ellipti-
cal crosstrainer must be connected to your portable
CD player, portable stereo, home stereo, or computer
with CD player. Refer to this page and page 14 for
connecting instructions.
A. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the included
adapter. Plug the adapter into an AUDIO OUT jack
on your stereo.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT
and PHONES jacks, see instruction A below. If
your CD player has only one jack, see instruction
B.
A/B
AUDIO OUT
RIGHT
LEFT
A. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the LINE OUT
jack on your CD player. Plug your headphones into
the PHONES jack.
Adapter
Audio Cable
A
PHONES LINE OUT
B. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the LINE OUT
jack on your stereo. Do not use the adapter.
LINE OUT
PHONES
Head-
phones
Audio
Cable
C. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into a 3.5mm Y-
adapter (available at electronics stores). Plug the Y-
adapter into the PHONES jack on your stereo. Plug
your headphones into the other side of the Y-
adapter.
B. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into a 3.5mm Y-
adapter (available at electronics stores). Plug the Y-
adapter into the PHONES jack on your CD player.
Plug your headphones into the other side of the Y-
adapter.
C
PHONES
B
3.5mm
Audio
Y-adapter
Cable
PHONES
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT
jack, see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the included
adapter. Plug the adapter into the LINE OUT jack
on your stereo.
A. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the LINE OUT
jack on your computer.
A
A
LINE OUT
CD
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Adapter
Audio Cable
B. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into a 3.5mm Y-
adapter (available at electronics stores). Plug the Y-
adapter into the PHONES jack on your computer.
Plug your headphones or speakers into the other
side of the Y-adapter.
B. Plug one end of the audio cable into the jack
beneath the console of the elliptical crosstrainer.
Plug the other end of the cable into the included
adapter. Plug the adapter into an RCA Y-adapter
(available at electronics stores). Next, remove the
wire that is currently plugged into the LINE OUT
jack on your stereo and plug the wire into the
unused side of the RCA Y-adapter. Plug the RCA
Y-adapter into the LINE OUT jack on your stereo.
B
PHONES
B
CD
3.5mm
Y-adapter
VCR
Audio Cable
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
14
Download from Www.Somanuals.com. All Manuals Search And Download.
During the CD program, the resistance of the ped-
als will automatically change according to the set-
tings of the program. An electronic ÒchirpingÓ sound
will alert you when the resistance is about to
change. If the resistance setting is too high or too
low, you can manually override the setting at any
time by pressing the RESISTANCE buttons on
the console. However, when the next ÒchirpÓ is
heard, the resistance will change back to the next
setting for the program.
HOW TO USE IFIT.COM CDÕS
IFit.com CDÕs (available separately) automatically con-
trol the resistance of the pedals as a personal trainer
coaches you through every step of your workout. For
information about purchasing CDÕs, call toll-free 1-800-
999-3756.
Before using iFit.com CDÕs, you must connect the
elliptical crosstrainer to your CD player. Refer to
pages 13 and 14 for connecting instructions. Follow
the steps below to use iFit.com CDÕs.
Note: If the resistance of the pedals does not
change when a ÒchirpÓ is heard:
¥ make sure that the indicator on the IFIT.COM
button is lit
Make sure that the power supply is plugged in.
1
Refer to page 9.
¥ adjust the volume of your CD player. If the
volume is too high or too low, the console
may not detect the program signals
Press any button on the console or move the
pedals to turn on the power.
2
¥ make sure that the audio cable is properly
connected and that it is fully plugged in.
When one of the buttons on the console is
pressed or the pedals are moved, various displays
and indicators will light and the left LED display
will begin to flash. Note: If the power supply was
just plugged in, the power will already be on.
Watch your progress with the program display,
the training zone display, and the LED displays.
6
Refer to step 5 on pages 10 and 11.
Measure your heart rate, if desired.
Refer to step 6 on page 11.
Select the iFit.com mode.
3
7
8
When the power is
turned on, the
manual mode will
be selected and
the manual indica-
tor will light. To
When the program is finished, turn off the
power.
select the iFit.com
mode, press the IFIT.COM button. The indicator
on the button will light.
To turn off the power, simply wait for about ten
minutes. The console has an Òauto-offÓ feature.
If the console buttons are not pressed and
the pedals are not moved for ten minutes, the
console will turn off automatically.
Insert the iFit.com CD into your CD player.
4
Note: If the displays and indicators remain lit
after ten minutes, the console may be in the
ÒdemoÓ mode. Refer to the instructions on
page 16 to turn off the demo mode.
Press the play button on your CD player to
start the program.
5
A moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainerÕs
instructions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
The right LED display
will show the total num-
ber of miles that the
pedals have moved.
The console features an information mode that keeps
track of the total number of hours that the elliptical
crosstrainer has been used and the total number of
miles that the pedals have moved. The information
mode also allows you to switch the console from miles
to kilometers. In addition, the information mode allows
you to turn on and turn off the demo mode.
IMPORTANT: Make
sure that there is not
a ÒdÓ in the right dis-
play. If a ÒdÓ appears in
the display, the console
is in the ÒdemoÓ mode.
This mode is intended to be used only when an elliptical
crosstrainer is displayed in a store. When the console
is in the demo mode, the power supply can be plugged
in and the displays and indicators on the console will
automatically light in a preset sequence, although the
buttons on the console will not operate. If a ÒdÓ
appears in the right display when the information
mode is selected, press the SELECT WORKOUT
button so the ÒdÓ disappears.
To select the information mode, press the RESIS-
TANCE button labeled Ò1Ó and the SELECT WORK-
OUT button at the same time. The following informa-
tion will be shown:
The left LED display will
show the total number
of hours that the ellipti-
cal crosstrainer has
been used. In addition,
an ÒEÓ for English miles
or an ÒMÓ for metric kilo-
meters will appear in the display. Press the START
PROGRAM button to change the unit of measurement,
if desired.
To exit the information mode, press the RESISTANCE
button labeled Ò1Ó and the SELECT WORKOUT button
at the same time.
MAINTENANCE
For smooth
operation of
the elliptical
crosstrainer,
the incline
from the incline frame where the wheels make contact
with it. Other parts of the elliptical crosstrainer can
also be cleaned in this manner. Never use abrasives
or solvents.
Incline
Frame
frame should
be kept clean.
Inspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.
Using a soft
cloth and mild
detergent,
Wheel
clean dust and
other residue
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
WARNING:
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
WORKOUT GUIDELINES
Each workout should include the following three
important parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise
program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
To find the proper heart rate for you, first find your age
on the bottom line of the chart (ages are rounded off
to the nearest ten years). Next, find the three numbers
above your age. The three numbers are your Òtraining
zone.Ó The lowest number is the recommended heart
rate for fat burning; the middle number is the recom-
mended heart rate for maximum fat burning; the high-
est number is the recommended heart rate for aerobic
exercise.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
To measure your heart rate, first exercise for at least
four minutes. Then, measure your heart rate using the
pulse sensor (see step 6 on page 11).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. NTEL08990
R0100A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
1
1
2
1
1
1
4
1
4
1
2
2
1
2
2
4
6
1
1
13
1
1
1
2
6
4
2
2
4
1
1
2
1
2
1
1
6
4
2
2
1
Frame
Upright
Left Pedal Arm
Right Pedal Arm
Incline Frame
Crank Arm
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
#
1
1
1
1
1
1
1
1
1
1
2
1
2
2
2
4
2
1
1
2
1
1
1
1
10
8
2
1
4
2
1
2
3
4
4
2
2
2
2
1
4
1
1
1
2
1
Right Side Shield
Console Base
Reed Switch/Wire
Harness Extension
Reed Switch Bracket
Resistance Cable
Reed Switch Clamp
Magnet
ÒCÓ Magnet
Stop Bolt
M8 Split Washer
Rear Stabilizer
Rear Stabilizer Bolt
3/4Ó Axle Cap
Front Stabilizer Endcap
Pedal Arm Cap
Rear Stabilizer Endcap
ÒJÓ Bolt Nut
ÒJÓ Bolt
M10 Nylon Jam Nut
Eyebolt
M6 Nylon Locknut
Adjustment Bracket
M4 x 63.5mm Screw
M4 x 16mm Screw
M5 x 16mm Screw
Axle Cover
Right Upper Body Arm
Pedal Bushing
Pedal Wheel
Left Upper Body Arm
Large Pulley
9
Frame Bearing
Plastic Crank Spacer
Flat Delrin Washer
Idler Bracket
Nut
Front Stabilizer
Push Nut
Idler Arm Screw
M10 Flat Washer
Foam Grip
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Arm Axle
Plastic Arm Sleeve
Chrome Tube
Extension Tube Bushing
Arm Bushing
Side Shield Support
Wire Harness/Resistance Motor
M10 Nylon Locknut
Incline Knob
Belt
Incline Axle
Incline Axle Screw
Incline Bushing
Incline Frame Cap
M8 Washer
Power Supply
Pedal Wheel Bolt
M8 Nylon Locknut
M8 Black Washer
Wheel Spacer
Pivot Axle Cap
Console Screw
Spring
Flange Bolt
Flywheel
Chrome Tube Washer
Plastic Pedal Spacer
Front Stabilizer Bolt
Console
M5 x 25mm Screw
Grease
Teflon¨ Lubricant
Push Nut Tool
Allen Wrench
Flywheel Bearing
Flywheel Axle
Pedal Disk
Left Pedal
Right Pedal
Pedal Screw
Console Washer
Wheel
Wheel Bolt
Left Side Shield
#
#
#
#
UserÕs Manual
Note: # indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. NTEL08990
R0100A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be
prepared to give the following information when calling:
¥ The MODEL NUMBER of the product (NTEL08990)
¥ The NAME of the product (NordicTrack¨ VGR940 elliptical crosstrainer)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the part(s) (see page 18 of this manual).
LIMITED WARRANTY
WHAT IS COVEREDÑThe entire NordicTrack¨ VGR940 elliptical crosstrainer (ÒProductÓ) is warranted to be free of all defects in
material and workmanship.
WHO IS COVEREDÑThe original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVEREDÑICON Health & Fitness, Inc. (ÒICONÓ), warrants the product for one year after the date of purchase.
Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTSÑWe will ship to you, without charge, any replacement part or component, pro-
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our
option, we will replace the Product.
WHAT IS NOT COVEREDÑAny failures or damage caused by unauthorized service, misuse, accident, negligence, improper assem-
bly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and maintain
as set out in your UserÕs Manual (ÒManualÓ).
WHAT YOU MUST DOÑAlways retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-
ed, return any defected part for replacement or, if necessary, the entire product, for repair.
USERÕS MANUALÑIt is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICEÑSimply call our Customer Service Department at 1-888-825-2588 and tell them your name
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service
where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-
lem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclu-
sion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 162528 R0100A
Printed in USA © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|