Model No. NEL7095.2
Serial No.
USER’S MANUAL
_
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser.
11. If you feel pain or dizziness while exercis-
ing, stop immediately and cool down.
12. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
in-home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
13. When you stop exercising, allow the pedals
to slowly come to a complete stop. The ellip-
tical exerciser does not have a free wheel;
the pedals will continue to move until the
flywheel stops.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use the elliptical exerciser.
14. Always unplug the power cord immediately
after use and before cleaning the elliptical
exerciser.
15. The decal shown below has been placed on
the elliptical exerciser. If the decal is missing
or illegible, call the toll-free telephone num-
ber on the front cover of this manual and
order a free replacement decal. Apply the
decal in the location shown.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothes when
using the elliptical exerciser. Always wear
athletic shoes for foot protection.
9. Always hold the handlebars when mounting,
dismounting, or using the elliptical exerciser.
10. Keep your back straight when using the ellip-
tical exerciser; do not arch your back.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the new NordicTrack®
CX 998 elliptical exerciser. The CX 998 is an incredi-
bly smooth exerciser that moves your feet in a natural
elliptical path, minimizing the impact on your knees
and ankles. And the unique CX 998 features
adjustable resistance and incline to help you get the
most from your exercise. Welcome to a whole new
world of natural, elliptical-motion exercise from
NordicTrack.
tions after reading this manual, please see the front
cover of this manual. To help us assist you, please
note the product model number and serial number
before calling. The model number is NEL7095.2. The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manual
for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
Fan
Upper Body Arm
Console
FRONT
Handlebar
Pulse Sensor
Water Bottle Holder*
Upright
Ramp
Wheel
Pedal
Pedal Leg
BACK
Power Socket
RIGHT SIDE
Leveling Foot
*No Water Bottle is included.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included allen wrenches, assembly requires a phillips screwdriver
wrenches , a rubber mallet , and pliers
, two adjustable
.
As you assemble the elliptical exerciser, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing is the key number of the part, from the PART LIST on pages 24
and 25. The second number is the quantity used in assembly. Note: Some small parts may have been pre-
assembled. If a part is not in the parts bag, check to see if it is pre-assembled.
M4 x 12mm
Round Head
Screw (96)–1
M4 x 16mm
Screw (98)–2
7.6mm Spacer
(109)–2
M8 Jam Nut
(86)–9
M6 Washer M8 Split
M10 Split
Washer
(73)–2
(64)–2
Washer
(30)–4
M4 x 16mm
Round Head
Screw (69)–4
M6 x 16mm Patch
Screw (76)–4
M8 x 41mm Button
Bolt (85)–4
M8 x 56mm Button Screw (83)–4
M8 x 44mm Button Screw (84)–8
M8 x 79mm Bolt Set (65)–2
M10 x 108mm Button Screw (70)–2
M8 x 38mm Button Bolt
(105)–2
1. Identify the Front Stabilizer (8). While another person
lifts the front of the Frame (1) and holds the Pedal
Legs (4, 5) in the position shown, attach the Front
Stabilizer to the Frame with four M8 x 44mm Button
Screws (84) and a Support Plate (104).
1
1
4, 5
While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (not shown) to the Frame
in the same way.
8
84
104
84
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Identify the Pivot Axle (14), which is the longer of the
two axles. Slide a Ramp Cover (48) onto an M6 x
16mm Patch Screw (76) as shown. Tighten the Patch
Screw into one end of the Pivot Axle. Apply a small
amount of the included grease to the Pivot Axle.
2
76
Tubes
48
Have a second person hold the two Ramp Spacers
(99) against the sides of the Frame (1) so they cover
the indicated tubes on the Frame. Align the round
tubes on the Ramp (3) with the Ramp Spacers. Make
sure that the Ramp is turned as shown in drawing
3 below. Insert the Pivot Axle (14) into the Ramp, the
Ramp Spacers, and the Frame. If necessary, use a
rubber mallet to fully insert the Pivot Axle.
3
Grease
99
48
Slide the other Ramp Cover (48) onto an M6 x 16mm
Patch Screw (76) as shown. Tighten the Patch Screw
into the open end of the Pivot Axle (14).
14
99
Tubes
1
76
3. Slide an M6 Washer (64) onto an M6 x 16mm Patch
Screw (76). Tighten the Patch Screw into one end of
the Incline Axle (13). Apply a small amount of grease
to the Incline Axle.
3
Motor
Screw
Raise the Ramp (3). Insert the Incline Axle (13) into
the welded tube under one side of the Ramp, through
the motor screw, and then into the welded tube under
the other side of the Ramp. As you insert the Incline
Axle through the motor screw, make sure that the
motor screw does not turn.
76
64
3
Grease
64
Slide an M6 Washer (64) onto an M6 x 16mm Patch
Screw (76). Tighten the Patch Screw into the open
end of the Incline Axle (13).
76
13
4. Have another person hold the Upright (2) in the posi-
tion shown.
4
Pull
Connect the Upper Wire Harness (115) to the Lower
Wire Harness (42). Insert the connectors on the Wire
Harnesses up into the Upright (2). Carefully pull the
upper end of the Upper Wire Harness to remove
the slack from the Wire Harnesses.
2
Do not pinch
the wire
harnesses
during this
step.
Insert the Upright (2) into the Frame (1). Be careful to
avoid pinching the Wire Harnesses (115, 42). Attach
the Upright with two M10 x 108mm Button Screws
(70), two M10 Split Washers (73), and two 7.6mm
Spacers (109). Make sure that the curved sides of
the Spacers are facing the Upright. Be careful to
avoid damaging the Wire Harnesses with the
Button Screws. Do not tighten the the Button
Screws yet.
73
115
42
1
109
70
73
109
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slide a Weld Spacer (119) onto the axle on the left
side of the Upright (2), with the open side of the Weld
Spacer facing the Upright. Apply a generous amount of
grease to the axle.
5
85
114
23
Hold one of the Upper Body Arms (118) with one hand,
hold the Upper Body Leg (31) with your other hand,
and slide the Upper Body Arm onto the axle on the left
side of the Upright (2). Next, extend the Upper Body
Leg and apply half of the included high-temperature
lubricant. Then, rest the end of the Upper Body Leg on
the Ramp (3).
20
24
86
Axle
119
118
Have another person hold the Left Handlebar (24)
near the Upright (2) as shown. Connect the left Pulse
Sensor Wire (20) to the Pulse Extension Wire (114).
105
Grease
118
2
Slide the upper end of the Left Handlebar (24) into the
tube on the front of the Upright (2), while sliding the
lower end of the Left Handlebar onto the axle on the
left side of the Upright. Attach the upper end of the Left
Handlebar with two M8 x 41mm Button Bolts (85) and
two M8 Jam Nuts (86); be careful not to damage the
Wires (20, 114) as you insert the Button Bolts.
Make sure that the Jam Nuts are resting in the
hexagonal holes in the Left Handlebar. Attach the
lower end of the Left Handlebar with an M8 x 38mm
Button Bolt (105) and an M8 Jam Nut (86).
86
3
Lubricate
31
Attach the other Upper Body Arm (118) and the Right
Handlebar (23) in the same way.
6. Look inside one of the Handlebar Cover Sets (26) and
locate the square tabs connecting the two halves.
Gently lift the tabs and disconnect the halves.
6
25
Hold the two halves of the Handlebar Cover Set (26)
around the tube on the left side of the Upright (2). Align
the halves and press them together until they lock.
Attach the other Handlebar Cover Set (26) to the right
side of the Upright (2) in the same way.
25
96
26
2
Hold the halves of the Upper Handlebar Cover (25)
around the tube on the front of the Upright (2); be
careful not to damage the Wires (not shown).
Attach the Upper Handlebar Cover with an M4 x
12mm Round Head Screw (96).
26
26
See the inset drawing. Attach the Water Bottle Holder
(108) to the Upright (2) with two M4 x 16mm Screws
(98).
108
98
2
98
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Apply a liberal amount of grease to the barrel of each
M8 x 79mm Bolt Set (65).
7
Identify the Left Pedal (10), which has a notch near
the right side. Place the Left Pedal on the Left Pedal
Leg (4). Have a second person hold the bracket on the
left Upper Body Leg (31) inside of the bracket on the
Left Pedal Leg, and hold a Pedal Wheel (28) inside of
the bracket on the left Upper Body Leg.
31
Notch
5
Holes
Align the indicated holes, and attach the Left Pedal
(10), the left Upper Body Leg (31), and the Wheel (28)
to the Left Pedal Leg (4) with an M8 x 79mm Bolt Set
(65). Attach the other end of the Left Pedal to the Left
Pedal Leg with two M8 x 56mm Button Screws (83)
and two M8 Split Washers (30).
10
Grease
4
Repeat this step on the right side of the elliptical
exerciser.
65
28
30
83
See step 4. Tighten the two M10 x 108mm Button
Screws (70).
65
8. Have another person hold the Console (17) near the
Upright (2).
8
Do not pinch
the wires
during this step.
17
Connect the Upper Wire Harness (115) to the wire har-
ness on the Console (17). Connect the Pulse
Extension Wire (114) to the pulse wire on the Console.
114
Carefully insert all excess wiring down into the Upright
(2). Attach the Console to the Upright with four M4 x
16mm Round Head Screws (69). (Note: The Round
Head Screws may be found in the console box.) Be
careful to avoid pinching the wires.
69
115
2
9. Plug the Power Cord (116) into the Power Socket
(117) at the rear of the elliptical exerciser.
9
116
117
10.Make sure that all parts of the elliptical exerciser are properly tightened. Cover the floor beneath the
elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO PLUG IN THE POWER CORD
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in
place by a metal screw. Some 2-pole receptacle out-
let box covers are not grounded. Contact a quali-
fied electrician to determine if the outlet box cover
is grounded before using an adapter.
This product
must be
grounded.
If it should
malfunction
or break
Grounded Outlet Box
Grounding Plug
down,
grounding
provides a
path of least
resistance for
electric
current to reduce the risk of electric shock. This prod-
uct is equipped with a cord having an equipment-
grounding conductor and a grounding plug. Plug the
power cord into an appropriate outlet that is prop-
erly installed and grounded in accordance with all
local codes and ordinances. This product is for
use on a nominal 120-volt circuit. Important: The
elliptical exerciser is not compatible with GFCI-
equipped outlets.
Note: When the power cord is plugged in, the ellip-
tical exerciser’s incline system may automatically
calibrate itself. During the calibration process,
three dashes (– – –) will appear in the console dis-
play while the ramp moves to the highest position
and then returns to the lowest position.
Grounding Pin
Grounded Outlet
EXERCISING ON THE ELLIPTICAL EXERCISER
To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lowest position.
Next, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion.
Handlebar
DANGER:
Improper connection of
the equipment-grounding conductor can result
in an increased risk of electric shock. Check
with a qualified electrician or serviceman if
you are in doubt as to whether the product is
properly grounded. Do not modify the plug
provided with the product—if it will not fit the
outlet, have a proper outlet installed by a qual-
ified electrician.
A temporary
Pedals
adapter may
be used to
Grounded Outlet Box
connect the
power cord
to a 2-pole
receptacle
as shown at
the right if a
properly
Adapter
Lug
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. The elliptical exerciser
does not have a free wheel; the pedals will contin-
ue to move until the flywheel stops. When the ped-
als are stationary, step off the highest pedal first.
Then, step off the lowest pedal.
Metal Screw
grounded
outlet is not
available. The temporary adapter should be used only
until a properly grounded outlet can be installed by a
qualified electrician.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Note: If there is a sheet of clear plastic on the face
of the console, remove it before using the console.
FEATURES OF THE CONSOLE
audio cable, you can connect the elliptical exerciser to
your portable stereo, home stereo, computer, or VCR
and play special iFIT.com CD and video programs
(iFIT.com CDs and videocassettes are available sepa-
rately). iFIT.com programs automatically control the
The advanced console offers a selection of features
designed to make your workouts more enjoyable and
effective. When the manual mode of the console is
selected, the resistance of the pedals and the angle of resistance of the pedals and prompt you to vary your
the ramp can be changed with the touch of a button.
As you exercise, the console will provide continuous
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor.
pace as a personal trainer coaches you through every
step of your workout. High-energy music provides
added motivation. To purchase iFIT.com CDs and
videocassettes, call the toll-free telephone number
on the front cover of this manual.
The console also offers eight preset programs. Each
program automatically changes the resistance of the
pedals and prompts you to increase or decrease your
pace as it guides you through an effective workout.
With the elliptical exerciser connected to your comput-
er, you can also go to our Web site at www.iFIT.com
and access programs directly from the internet.
Explore www.iFIT.com for more information.
In addition, the console features two heart rate pro-
grams that automatically change the resistance of the
pedals and prompt you to vary your pace to keep your
heart rate near a target heart rate while you exercise.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a preset
program, see page 13. To use a heart rate program,
see page 14. To use an iFIT.com CD or video pro-
gram, see page 19. To use an iFIT.com program
directly from our Web site, see page 20.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com technology is like having a per-
sonal trainer in your home. Using the included stereo
10
Download from Www.Somanuals.com. All Manuals Search And Download.
you exercise, the indicators around the track will
light in succession until the entire track is lit. The
track will then darken and the indicators will again
begin to light in succession.
HOW TO USE THE MANUAL MODE
Press any button on the console or begin
pedaling to turn on the console.
1
The Training Zones
bar—The Training
Zones bar will show
the approximate inten-
sity level of your exer-
cise.
Make sure that the power cord is properly
plugged in (see page 9). To activate the con-
sole, press any button or begin pedaling. After a
few seconds, the displays will light. A tone will
then sound and the console will be ready for use.
Select the manual mode.
2
3
If you have selected
a program or the
iFIT.com mode, rese-
lect the manual mode
by pressing the iFIT
button once or twice
until a track appears
in the matrix but the letters “iFIT” do not appear.
The upper display—
The upper display will
show the approximate
number of grams of
carbs you have
burned, the approxi-
mate number of calo-
ries you have burned, the distance you have ped-
aled, and the elapsed time. The display will
change from one number to the next every few
seconds. Note: When a program is selected, the
display will show the time remaining in the pro-
gram instead of the elapsed time.
Change the resistance of the pedals and the
angle of the ramp as desired.
As you pedal,
change the resis-
tance of the pedals
by pressing the 1
Step Resistance but-
tons. Note: After the
buttons are pressed,
it will take a moment for the pedals to reach the
selected resistance level.
To see the total distance pedaled since the ellipti-
cal exerciser was purchased, press the Odometer
button twice; the words “Total Dist.” and the total
number of miles will appear in the display. To
again see the distance that you have pedaled
during your workout, press the Odometer button
again.
To vary the feel of
your exercise,
increase or decrease
the angle of the
ramp by pressing the
1 Step Ramp but-
tons. There are five
ramp angles. Note: After the buttons are pressed,
it will take a moment for the ramp to reach the
selected angle.
The lower display—
The lower display will
show your pedaling
pace, in revolutions
per minute (RPM),
your pedaling speed,
and the resistance
level of the pedals. The display will change from
one number to the next every few seconds. The
display will also show your heart rate when you
use the handgrip pulse sensor.
Monitor your progress with the matrix, the
Training Zones bar, and the displays.
4
The matrix—When
the manual mode or
the iFIT.com mode is
selected, the matrix
will show a track rep-
resenting 1/4 mile. As
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The console
can show speed
and distance in
either miles or kilo-
Note: If you continue to hold the handgrip pulse
sensor, the lower display will show your heart rate
for up to 30 seconds. The display will then show
your heart rate along with the other modes.
meters. The letters
MPH or Km/H will
appear in the lower
If your heart rate is not shown, make sure that
your hands are positioned as described. Be care-
ful not to move your hands excessively or to
squeeze the metal contacts too tightly. For opti-
mal performance, clean the metal contacts using
a soft cloth; never use alcohol, abrasives, or
chemicals.
display to show which unit of measurement is
selected. To change the unit of measurement, first
hold down the Start button for a few seconds. An E
(for English) or an M (for metric) will appear in the
lower display. Press the 1 Step Resistance 10 but-
ton to change the unit of measurement.
Turn on the fan if desired.
6
While you are select-
To turn on the fan at
ing a unit of mea-
surement, you can
low speed, press the
Auto Breeze Fan but-
also select a back-
ton; the number 1 will
light mode. The “On”
appear next to the
mode keeps the
word “Fan” in the dis-
backlight on while
play. To turn on the
the console is on. The “Off” mode turns the back-
light off. The “Auto” mode keeps the backlight on
only while you are exercising. Press the 1 Step
Resistance 1 button to change the backlight mode
if desired. Then, press the Start button.
fan at medium speed, press the button a second
time; the number 2 will appear. To turn on the fan
at high speed, press the button a third time; the
number 3 will appear. To select the auto mode,
press the button again; the words “Auto Fan” will
appear. When the auto mode is selected, the
speed of the fan will automatically increase or
decrease as you increase or decrease your ped-
aling speed.
Measure your heart rate if desired.
5
If there are
thin sheets of
plastic on the
metal con-
tacts on the
handgrip
To turn off the fan, press the Auto Breeze Fan
button again. Note: If the pedals are not turned
for a few minutes, the fan will automatically turn
off.
pulse sensor,
peel off the
Contacts
Slide the thumb tab on the right side of the fan to
pivot the fan to the desired angle.
plastic. To
measure your
heart rate,
hold the handgrip pulse sensor, with your palms
resting against the metal contacts. Avoid moving
your hands or gripping the contacts tightly.
When you are finished exercising, the console
will automatically turn off.
7
If the pedals are not moved for several seconds, a
tone will sound, the console will pause, and the
time will begin to flash in the upper display.
When your pulse is
detected, your heart
rate will be shown in
the lower display. For
the most accurate
heart rate reading,
hold the contacts for
at least 15 seconds.
If the pedals are not moved for about five min-
utes, the console will turn off and the displays will
be reset.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
When the one of the “Too Fast” indicators lights,
decrease your pace. When the “On Pace” indica-
tor lights, maintain your current pace.
HOW TO USE A PRESET PROGRAM
Press any button on the console or begin
pedaling to turn on the console.
1
See step 1 on page 11.
Select one of the eight preset programs.
2
To select one of the
eight preset pro-
grams, press the
Resistance/Pace
Programs button
repeatedly until
“P 1,” “P 2,” “P 3,”
“P 4,” “P 5,” “P 6,” “P 7,” or “P 8” appears in the
upper display.
Important: The pace settings are intended
only to provide motivation. Your actual pace
may be slower than the pace settings. Make
sure to exercise at a pace that is comfortable
for you.
When a preset program is selected, a profile of
the resistance settings of the program will scroll
across the matrix and the maximum resistance
setting of the program will flash in the lower dis-
play. A few seconds after a program is selected,
the upper display will show how long the program
will last.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a
series of tones will sound, and all resistance set-
tings will move one column to the left. The resis-
tance setting for the second segment will then be
shown in the flashing Current Segment column,
and the resistance of the pedals will change to the
resistance setting for the second segment. Note: If
all of the indicators in the Current Segment col-
umn are lit after the resistance settings have
moved to the left, the resistance settings may
move downward so only the highest indicators
appear in the matrix.
Press the Start button or begin pedaling to
start the program.
3
Each program is divided into several one-minute
segments. One resistance setting and one pace
setting are programmed for each segment. Note:
The same resistance setting and/or pace setting
may be programmed for two or more consecutive
segments.
The program will continue until the resistance
setting for the last segment is shown in the
Current Segment column and the last segment
ends.
The resistance
setting for the first
segment will be
shown in the
Current Segment
Note: During the program, you can override the
resistance setting for the current segment, if
desired, by pressing the 1 Step Resistance but-
tons. However, when the next segment begins,
the resistance will change if a different resistance
setting is programmed for the next segment. In
addition, you can change the angle of the ramp,
if desired, by pressing the 1 Step Ramp buttons.
flashing Current
Segment column
of the matrix. (The
pace settings are not shown in the matrix.) The
resistance settings for the next several segments
will be shown in the columns to the right.
As you exercise, the Target Pace guide will help
you to keep your pedaling pace near the pace
setting for the current segment. When one of the
“Too Slow” indicators lights, increase your pace.
If you stop pedaling for several seconds, a tone
will sound and the program will pause. To restart
the program, simply resume pedaling.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor your progress with the displays.
See step 4 on page 11.
HOW TO USE A HEART RATE PROGRAM
Press any button on the console or begin
4
5
6
7
1
pedaling to turn on the console.
Measure your heart rate if desired.
See step 5 on page 12.
See step 1 on page 11.
Select one of the two heart rate programs.
Turn on the fan if desired.
See step 6 on page 12.
2
To select a heart rate
program, press the
Heart Rate Control
Programs button once
or twice until “P 9” or
When you are finished exercising, the con-
sole will automatically turn off.
“P10” appears in the
See step 7 on page 12.
upper display. A few
seconds after a program is selected, the upper
display will show how long the program will last.
If the first heart rate
program (P 9) is
selected, a profile of
the target heart rate
settings of the pro-
gram will scroll across
the matrix.
If the second heart
rate program (P10)
is selected, a pulse
symbol will appear in
the matrix.
Enter a target heart rate setting.
3
If the first heart rate
program is selected,
the maximum target
heart rate setting of
the program will flash
in the lower display. If
desired, press the
increase and decrease buttons to change the
maximum target heart rate setting (see EXER-
CISE INTENSITY on page 23). Note: If the maxi-
mum target heart rate setting is changed, the
intensity level of the entire program will change.
If the second heart rate program is selected,
the target heart rate setting for the program will
flash in the lower display. If desired, press the
increase and decrease buttons to change the tar-
get heart rate setting (see EXERCISE INTENSI-
TY on page 23). Note: The same target heart
rate setting will be programmed for all segments.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold the handgrip pulse sensor.
The Target Pace guide will prompt you to
increase or decrease your pedaling pace during
the program. When one of the “Too Slow” indica-
tors lights, increase your pace. When the one of
the “Too Fast” indicators lights, decrease your
pace. When the “On Pace” indicator lights, main-
tain your current pace.
4
5
To use a heart rate program, you must use the
handgrip pulse sensor. It is not necessary to hold
the handgrip pulse sensor continuously during
the program; however, you should hold the hand-
grip pulse sensor frequently for the program to
operate properly. Each time you hold the hand-
grip pulse sensor, keep your hands on the
metal contacts for at least 30 seconds.
Press the Start button to start the program.
First heart rate program—This program is divid-
ed into 20 one-minute segments. One target
heart rate setting is programmed for each seg-
ment. Note: The same target heart rate setting
may be programmed for two or more consecutive
segments.
Important: The target heart rate settings are
intended only to provide motivation. Your
actual heart rate may be slower than the tar-
get heart rate settings. Make sure to exercise
at a pace that is comfortable for you.
The target heart
rate setting for the
first segment will
be shown in the
Current Segment
flashing Current
Segment column
of the matrix. The
target heart rate
settings for the next several segments will be
shown in the columns to the right.
Note: During the program, you can manually over-
ride the resistance setting for the current seg-
ment, if desired, with the 1 Step Resistance but-
tons. However, when the console compares your
heart rate to the target heart rate setting, the
resistance of the pedals may automatically
increase or decrease to bring your heart rate
closer to the target heart rate setting. In addition,
you can change the angle of the ramp, if desired,
by pressing the 1 Step Ramp buttons.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a
series of tones will sound, and all target heart
rate settings will move one column to the left.
The target heart rate setting for the second seg-
ment will then be shown in the flashing Current
Segment column.
If you stop pedaling for several seconds, a tone
will sound and the program will pause. To restart
the program, simply resume pedaling.
Second heart rate program—This program is
divided into 40 one-minute segments. The same
target heart rate is programmed for all segments.
Note: For a shorter workout, stop exercising or
select a different program before the program
ends.
Monitor your progress with the displays.
See step 4 on page 11.
6
7
8
Turn on the fan if desired.
See step 6 on page 12.
Both heart rate programs—As you pedal, the
console will regularly compare your heart rate to
the target heart rate setting. If your heart rate is
too far below or above the target heart rate set-
ting, the resistance of the pedals will automatical-
ly increase or decrease to bring your heart rate
closer to the target heart rate setting.
When you are finished exercising, the con-
sole will automatically turn off.
See step 7 on page 12.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1/8” LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the elliptical exerciser must be
connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
16 and 17 for connecting instructions. To use iFIT.com
videocassettes, the elliptical exerciser must be con-
nected to your VCR. See page 18 for connecting
instructions. To use iFIT.com programs directly from
our Web site, the elliptical exerciser must be connect-
ed to your home computer. See page 17 for connect-
ing instructions.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into an
AUDIO OUT jack on your stereo.
A, B
AUDIO OUT
HOW TO CONNECT YOUR PORTABLE CD PLAYER
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Adapter
Audio Cable
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your CD player.
Plug your headphones into the PHONES jack.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your stereo. Do
not use the adapter.
A
PHONES LINE OUT
C. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the
other side of the Y-adapter.
LINE OUT
PHONES
Head-
phones
Audio
Cable
C
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your CD player. Plug your headphones into the
other side of the Y-adapter.
PHONES
1/8”
Y-adapter
Audio
Cable
B
PHONES
Headphones
PHONES
1/8”
Y-adapter
Audio
Cable
Headphones
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 1/8” LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into the
LINE OUT jack on your stereo.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
A
A
LINE OUT
CD
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speak-
ers into the other side of the Y-adapter.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the LINE OUT jack on your stereo and plug the
wire into the unused side of the Y-adapter. Plug the
Y-adapter into the LINE OUT jack on your stereo.
B
PHONES
B
CD
1/8”
Audio
Y-adapter
Cable
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the AUDIO OUT jack on your VCR and plug the
wire into the unused side of the Y-adapter. Plug the
Y-adapter into the AUDIO OUT jack on your VCR.
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 17.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into the
AUDIO OUT jack on your VCR.
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A
RCA Y-adapter
Adapter
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
AUDIO OUT
Audio Cable
RIGHT
LEFT
Wire removed from
AUDIO OUT jack
Adapter
Audio Cable
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The program will function in almost the same way
as a preset program (see step 3 on page 13).
However, an electronic “chirping” sound will alert
you when the resistance setting and/or pace set-
ting is about to change.
HOW TO USE AN IFIT.COM CD OR VIDEO
PROGRAM
To use an iFIT.com CD or video program, the elliptical
exerciser must be connected to your CD player or
VCR. See HOW TO CONNECT YOUR CD PLAYER,
VCR, OR COMPUTER on pages 16 to 18. To pur-
chase iFIT.com CDs or videocassettes, call the toll-
free telephone number on the front cover of this
manual.
Note: If the resistance of the pedals and/or the
pace setting does not change when a “chirp”
is heard:
• Make sure that the letters “iFIT” appear in
the display.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
Follow the steps below to use an iFIT.com CD or
video program.
Press any button on the console or begin
pedaling to turn on the console.
• Make sure that the audio cable is properly
connected and that it is fully plugged in.
1
See step 1 on page 11.
Monitor your progress with the displays.
See step 4 on page 11.
4
5
6
7
Select the iFIT.com mode.
2
To select the
Measure your heart rate as desired.
See step 5 on page 12.
iFIT.com mode, press
the iFIT button. The
track and the letters
“iFIT” will light.
Turn on the fan if desired.
See step 6 on page 12.
Press the Play button on your CD player or
VCR.
3
When you are finished exercising, the console
will automatically turn off.
Note: If you are using an iFIT.com CD, insert the
CD into your CD player; if you are using an
iFIT.com videocassette, insert the videocassette
into your VCR.
See step 7 on page 12.
A moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow the on-line instructions to start the
program.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
6
7
When you start the program, an on-screen count-
down will begin.
Our Web site at www.iFIT.com allows you to play
iFIT.com programs directly from the internet. To use
programs from our Web site, the elliptical exerciser
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 17. In
addition, you must have an internet connection and an
internet service provider. A list of specific system
requirements is found on our Web site.
Return to the elliptical exerciser and begin
pedaling.
When the on-screen countdown ends, the pro-
gram will begin. The program will function in
almost the same way as a preset program (see
step 3 on page 13). However, an electronic “chirp-
ing” sound will alert you when the resistance set-
ting and/or pace setting is about to change.
Follow the steps below to use a program from our
Web site.
Monitor your progress with the displays.
See step 4 on page 11.
Press any button on the console or begin
pedaling to turn on the console.
8
1
See step 1 on page 11.
Measure your heart rate if desired.
See step 5 on page 12.
9
Select the iFIT.com mode.
2
See step 2 on page 19.
Turn on the fan if desired.
10
11
Go to your computer and start an internet
connection.
3
See step 6 on page 12.
When you are finished exercising, the con-
sole will automatically turn off.
Start your Web browser, if necessary, and go
to our Web site at www.iFIT.com.
4
See step 7 on page 12.
Follow the desired links on our Web site to
5
select a program.
Read and follow the on-line instructions for using
a program.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and properly tighten all parts of the elliptical
exerciser regularly. Replace any worn parts immedi-
ately.
HOW TO MOVE THE ELLIPTICAL EXERCISER
Stand in front of the elliptical exerciser, hold the han-
dlebars firmly, and place one foot against the ramp in
the location shown below. Pull the handlebars until
the elliptical exerciser can be moved on the front
wheels, and carefully move the elliptical exerciser to
the desired location. Then, place one foot against the
ramp and lower the elliptical exerciser. Due to the
size and weight of the elliptical exerciser, use
extreme caution while moving and lowering it.
For smooth
operation of the
elliptical exer-
Ramp
ciser, inspect
and clean the
ramp regularly
using a soft
Wheel
cloth and mild
detergent.
Other parts of
the elliptical
exerciser can
also be cleaned
Handlebars
in this way.
Keep liquids off the console. Never use abrasives
or solvents.
PULSE SENSOR TROUBLESHOOTING
If the handgrip pulse sensor does not function proper-
ly, see step 5 on page 12.
Place your
foot here
HOW TO CALIBRATE THE INCLINE SYSTEM
If the elliptical exerciser’s ramp does not function prop-
erly, press one of the 1 Step Ramp buttons; while the
ramp is moving, unplug the power cord. When the
power cord is plugged back in, the elliptical exercis-
er’s incline system will automatically calibrate itself.
During the calibration process, three dashes (– – –)
will appear in the console display while the ramp
moves to the highest position and then returns to the
lowest position.
Wheel
HOW TO LEVEL THE ELLIPTICAL EXERCISER
If the elliptical
exerciser rocks
during use, turn
one or both of
the leveling feet
under the rear
stabilizer until
Leveling
Foot
the rocking
motion is elimi-
nated.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO REMOVE THE SIDE SHIELDS AND THE
FLYWHEEL COVERS
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first see the instructions at the left and remove
the side shields and the flywheel covers.
The Left and Right Side Shields (15, 16) must be
removed before the reed switch or the drive belt can
be adjusted. To remove the Side Shields, remove the
indicated Screws (69, 95, 97). Note which hole each
Screw is removed from; the Screws will later need to
be reattached in the same holes. Carefully separate
and remove the Side Shields.
Next, see the drawing below. Locate the Reed Switch
(55). Turn the Left Crank Arm (34) until the Magnet
(37) is aligned with the Reed Switch. Loosen, but do
not remove, the indicated Screw (98). Slide the Reed
Switch slightly closer to or away from the Magnet, and
then retighten the Screw. Turn the Left Crank Arm for
a moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjust-
ed, reattach the side shields and the flywheel covers.
16
95
69
95
97
113
69
15
34
98
37
69
75
55
Next, the Right
and Left
74
18
19
Flywheel Covers
(18, 19) must be
removed.
69
HOW TO ADJUST THE DRIVE BELT
97
Remove the
indicated
Screws (69, 97,
101) from the
Flywheel
Covers. Note
which hole each
Screw is
If you can feel the pedals slip while you are pedaling,
even when the resistance is adjusted to the highest
setting, the drive belt may need to be adjusted. To
adjust the drive belt, first see the instructions at the
left and remove the side shields and the flywheel
covers.
69
101
69
removed from; the Screws will later need to be reat-
tached in the same holes. Carefully separate and
remove the Flywheel Covers.
Next, see the drawing above. Loosen the indicated
Bolt (75). Turn the indicated Screw (74) clockwise
until the Drive Belt (113) is properly tightened, and
then retighten the Bolt (75). Then, reattach the side
shields and the flywheel covers.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
WARNING:
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone as you exercise.
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise
program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommend-
ed heart rate for aerobic exercise.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NEL7095.2
R1005A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
2
4
4
2
1
1
1
4
1
1
1
1
1
1
1
1
2
1
4
4
2
1
1
4
1
1
Frame
Upright
Ramp
Left Pedal Leg
Right Pedal Leg
Rear Stabilizer
Rear Stabilizer Cover
Front Stabilizer
Front Stabilizer Cover
Left Pedal
Right Pedal
Incline Motor
Incline Axle
Pivot Axle
Left Side Shield
Right Side Shield
Console
Right Flywheel Cover
Left Flywheel Cover
Pulse Sensor w/Wire
Right Incline Cover
Left Incline Cover
Right Handlebar
Left Handlebar
Upper Handlebar Cover
Handlebar Cover Set
Frame Cover
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
12
2
1
1
2
1
1
4
4
4
4
2
1
2
4
8
4
9
8
1
1
4
1
2
2
3
8
6
2
10
2
4
1
1
4
2
2
2
Clamp
Reed Switch/Wire
Return Spring
Guide Rod
Resistance Cable
Flywheel Axle
Flywheel Bearing
Eye Bolt
Adjustment Bracket
M8 x 47mm Button Screw
M6 Washer
M8 x 79mm Bolt Set
M8 Washer
M10 x 51mm Bolt Set
Handlebar Bushing
M4 x 16mm Round Head Screw
M10 x 108mm Button Screw
M8 Tek Washer
M11 x 40mm Bolt Set
M10 Split Washer
M8 x 25mm Button Bolt
M10 x 15mm Carriage Bolt
M6 x 16mm Patch Screw
M5 Nut
M5 x 16mm Bolt
M5 Washer
M6 x 12mm Bolt
M6 x 28mm Bolt
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Pedal Wheel
Wheel Bearing
M8 Split Washer
Upper Body Leg
“C” Magnet
Magnet Bracket
Left Crank Arm
28mm Pulley Spacer
Flywheel
5/16” x 25mm Flange Screw
M8 x 56mm Button Screw
M8 x 44mm Button Screw
M8 x 41mm Button Bolt
M8 Jam Nut
M4 x 38mm Screw
Incline Stop Plate
M10 Nylon Locknut
M6 Nut
Magnet
Pulley
Tension Spring
Snap Ring
Control Box Cover
Control Board
Control Box
Lower Wire Harness
Crank
Crank Bearing
Idler
Leveling Foot
Ramp Bushing
Ramp Cover
Incline Sensor
Sensor Cover
Pedal Leg Bushing
Resistance Motor
Reed Switch Bracket
M8 x 54mm Button Screw
M4 x 10mm Screw
M4 x 19mm Screw
M4 x 12mm Round Head Screw
M4 x 25mm Screw
M4 x 16mm Screw
Ramp Spacer
M5 Nylon Locknut
M4 x 16mm Round Head Screw
Right Crank Arm
Flywheel Washer
Support Plate
M8 x 38mm Button Bolt
Upper Foam Grip
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
107
108
109
110
111
112
113
114
115
116
117
118
2
1
2
4
2
2
1
1
1
1
1
2
Lower Foam Grip
Water Bottle Holder
7.6mm Spacer
Wheel Bushing
M8 x 19mm Patch Screw
Wheel
119
120
121
122
123
124
125
#
2
2
2
2
4
2
2
1
1
Weld Spacer
Sleeve
Upper Body Foam Grip
Upper Body Endcap
Upper Body Bushing
M5 x 5mm Screw
Wave Washer
High-temperature Lubricant
Grease
Allen Wrench
Belt
Pulse Extension Wire
Upper Wire Harness
Power Cord
Power Socket
Upper Body Arm
#
#
#
User’s Manual
Note: # indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. NEL7095.2
R1005A
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. NEL7095.2
R1005A
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be
prepared to give the following information when calling:
• The MODEL NUMBER of the product (NEL7095.2)
• The NAME of the product (NordicTrack CX 998 elliptical exerciser)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see pages 24 to 27)
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® elliptical exerciser (“Product”) is warranted to be free of all defects in material and
workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product for one year after the date of purchase.
Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component, pro-
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our
option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper assem-
bly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and maintain
as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-
ed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them your name
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service
where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-
lem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclu-
sion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 226764 R1005A
Printed in China © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|