Nokia Cell Phone 3109 User Manual

Nokia 3110 classic/Nokia 3109 classic User Guide  
9200417  
Issue 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C o n t e n t s  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For your safety  
Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.  
SWITCH ON SAFELY  
Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.  
ROAD SAFETY COMES FIRST  
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should  
be road safety.  
INTERFERENCE  
All wireless devices may be susceptible to interference, which could affect performance.  
SWITCH OFF IN HOSPITALS  
Follow any restrictions. Switch the device off near medical equipment.  
SWITCH OFF IN AIRCRAFT  
Follow any restrictions. Wireless devices can cause interference in aircraft.  
SWITCH OFF WHEN REFUELING  
Do not use the device at a refueling point. Do not use near fuel or chemicals.  
SWITCH OFF NEAR BLASTING  
Follow any restrictions. Do not use the device where blasting is in progress.  
USE SENSIBLY  
Use only in the positions as explained in the product documentation. Do not touch the antenna areas unnecessarily.  
QUALIFIED SERVICE  
Only qualified personnel may install or repair this product.  
ENHANCEMENTS AND BATTERIES  
Use only approved enhancements and batteries. Do not connect incompatible products.  
WATER-RESISTANCE  
Your device is not water-resistant. Keep it dry.  
BACK-UP COPIES  
Remember to make back-up copies or keep a written record of all important information stored in your device.  
CONNECTING TO OTHER DEVICES  
When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.  
EMERGENCY CALLS  
Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display  
and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call until  
given permission to do so.  
About your device  
The wireless device described in this guide is approved for use on the on the EGSM 900 and GSM 1800 and 1900 networks. Contact  
your service provider for more information about networks.  
When using the features in this device, obey all laws and respect local customs, privacy and legitimate rights of others, including  
copyrights.  
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified,  
transferred, or forwarded.  
Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device  
on when wireless device use may cause interference or danger.  
5
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
N e t w o r k s e r v i c e s  
Network services  
To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features  
are not available on all networks; other networks may require that you make specific arrangements with your service provider before you can  
use the network services. Your service provider can give you instructions and explain what charges will apply. Some networks may have  
limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and  
services.  
Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear  
on your device menu. Your device may also have a special configuration such as changes in menu names, menu order, and icons. Contact your  
service provider for more information.  
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as multimedia messaging  
(MMS), e-mail application, instant messaging, remote synchronization, and content downloading using the browser or MMS, require network  
support for these technologies.  
Shared memory  
The following features in this device may share memory: gallery, contacts, text messages, multimedia messages, and instant messages, e-mail,  
calendar, to-do notes, Java™ games and applications, and note application. Use of one or more of these features may reduce the memory  
available for the remaining features sharing memory. Your device may display a message that the memory is full when you try to use a shared  
memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing.  
Enhancements  
Practical rules about accessories and enhancements  
Keep all accessories and enhancements out of the reach of small children.  
When you disconnect the power cord of any accessory or enhancement, grasp and pull the plug, not the cord.  
Check regularly that enhancements installed in a vehicle are mounted and are operating properly.  
Installation of any complex car enhancements must be made by qualified personnel only.  
6
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
1.  
General information  
Access codes  
Security code  
The security code (5 to 10 digits) helps to protect your phone against unauthorized use. The preset code is 12345. You can  
change the code, and set the phone to request the code. See "Security," p. 28.  
PIN codes  
The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help  
to protect your SIM card against unauthorized use. See "Security," p. 28.  
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required for some functions.  
The module PIN is required to access the information in the security module. See "Security module," p. 39.  
The signing PIN is required for the digital signature. See "Digital signature," p. 39.  
PUK codes  
The personal unblocking key (PUK) code and the universal personal unblocking key (UPUK) code (8 digits) are required to change  
a blocked PIN code and UPIN code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2 code. If the codes  
are not supplied with the SIM card, contact your local service provider for the codes.  
Barring password  
The barring password (4 digits) is required when using the Call barring service. See "Security," p. 28.  
Configuration setting service  
To use some of the network services, such as mobile internet services, MMS, Nokia Xpress audio messaging, or remote internet  
server synchronization, your device needs the correct configuration settings. For more information on availability, contact your  
service provider, the nearest authorized Nokia dealer, or visit the support area on the Nokia website. See "Nokia  
When you have received the settings as a configuration message and the settings are not automatically saved and activated,  
Configuration sett. received is displayed.  
To save the settings, select Show > Save. If required, enter the PIN code supplied by the service provider .  
To discard the received settings, select Exit or Show > Discard.  
Download content  
You may be able to download new content (for example, themes) to your phone (network service).  
Important: Use only services that you trust and that offer adequate security and protection against harmful software.  
For the availability of different services, pricing, and tariffs, contact your service provider.  
Software updates  
Nokia may produce software updates that may offer new features, enhanced functions, or improved performance. You may be  
able to request these updates through the Nokia Software Updater PC application. To update the device software, you need the  
Nokia Software Updater application and a compatible PC with Microsoft Windows 2000 or XP operating system, broadband  
internet access, and a compatible data cable to connect your device to the PC.  
To get more information and to download the Nokia Software Updater application, visit www.nokia.com/softwareupdate or  
your local Nokia website.  
If software updates over the air are supported by your network, you may also be able to request updates through the device.  
Downloading software updates may involve the transmission of large amounts of data through your service provider's network.  
Contact your service provider for information about data transmission charges.  
Make sure that the device battery has enough power, or connect the charger before starting the update.  
Important: Use only services that you trust and that offer adequate security and protection against harmful software.  
7
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                 
G e t s t a r t e d  
Nokia support  
Support information  
downloads, and services related to your Nokia product.  
Configuration settings service  
You may also download free configuration settings such as MMS, GPRS, e-mail, and other services for your device model at  
Nokia PC Suite  
Customer service  
If you need to contact customer service, check the list of local Nokia Care contact centers at www.nokia.com/  
Maintenance  
For maintenance services, check your nearest Nokia service center at www.nokia.com/repair.  
2.  
Get started  
All graphics show the Nokia 3110 classic phone.  
Install SIM card and battery  
Always switch the device off and disconnect the charger before removing the battery.  
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider or  
other vendor.  
This device is intended for use with a BL-5C battery. Always use original Nokia batteries. See "Nokia battery authentication  
The SIM card and its contacts can be easily damaged by scratches or bending, so be careful when handling, inserting, or removing  
the card.  
1. Slide the release button (1) to unlock and remove the back cover (2). Remove the  
battery as shown (3).  
2. Open the SIM card holder (4). Insert the SIM card (5) with the contact surface facing  
down into the holder. Close the SIM card holder (6).  
3. Observe the battery contacts (7), and insert the battery (8). Place the upper part  
of the back cover on the device (9), and close it (10).  
Insert a microSD card  
Use only compatible microSD cards approved by Nokia for use with this device. Nokia uses approved industry standards for  
memory cards, but some brands may not be fully compatible with this device. Incompatible cards may damage the card and  
the device and corrupt data stored on the card.  
1. Switch the device off, and remove the back cover and the battery of the device.  
8
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
G e t s t a r t e d  
2. Slide the memory card holder to unlock (1).  
3. Open the card holder (2), and insert the memory card into the card holder with the contact surface  
facing inwards (3).  
4. Close the card holder (4), and slide the card holder to lock it (5).  
5. Insert the battery, and attach the back cover to the device.  
Charge the battery  
Check the model number of any charger before use with this device. This device is intended for use when supplied with power  
from the AC-3 or AC-4 charger.  
Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The  
use of any other types may invalidate any approval or warranty, and may be dangerous.  
For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any  
enhancement, grasp and pull the plug, not the cord.  
1. Connect the charger to a wall socket.  
2. Connect the lead from the charger to the socket on the bottom of your device.  
If the battery is completely discharged, it may take a few minutes before the charging indicator appears  
on the display or before any calls can be made.  
The charging time depends on the charger used. Charging a BL-5C battery with the AC-3 charger takes  
approximately 2 hours and 45 minutes while the device is in the standby mode.  
Antenna  
Your device has an internal antenna.  
Note: As with any other radio transmitting device, do not touch the antenna unnecessarily  
when the device is switched on. Contact with the antenna affects call quality and may cause  
the device to operate at a higher power level than otherwise needed. To optimize antenna  
performance and battery life, avoid contact with the antenna area when operating the  
device.  
Headset  
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing.  
Pay special attention to volume level if you connect any other headsets to the device.  
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset  
where it can endanger your safety.  
Do not connect products that create an output signal as this may cause damage to the device. Do not connect any  
voltage source to the Nokia AV Connector.  
When connecting any external device or any headset, other than those approved by Nokia for use with this device, to  
the Nokia AV Connector, pay special attention to volume levels.  
Strap  
1. Open the back cover.  
9
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Y o u r d e v i c e  
2. Hook a strap behind the clamp as shown in the picture (1) and close the back cover (2).  
3.  
Your device  
Keys and parts  
The Nokia 3110 classic phone is shown.  
1 — Earpiece  
2 — Display  
3 — Left selection key  
4 — Call key  
5 — Infrared (IR) port  
6 — Navi™ key: 4-way scroll key and middle selection key  
7 — Right selection key  
8 — End key  
9 — Keypad  
10 — Microphone  
11 — Charger connector  
12 — Nokia AV Connector (2.5 mm)  
13 — Mini USB cable connector  
14 — Volume down key  
15 — Volume up key  
16 — Power key  
17 — Loudspeaker  
18 — Camera lens (only Nokia 3110 classic)  
Switch the device on and off  
To switch the device on or off, press and hold the power key.  
If the device prompts for a PIN or a UPIN code, enter the code (displayed as ****), and select OK.  
The device may prompt you to set the time and date. Enter the local time, select the time zone of your location in terms of the  
time difference with respect to Greenwich mean time (GMT), and enter the date. See "Time and date," p. 24.  
When you switch on your device for the first time and the device is in the standby mode, you may be prompted to get the  
configuration settings from your service provider (network service). For more information refer to Connect to service provider  
Standby mode  
When the device is ready for use, and you have not entered any characters, the device is in the standby mode.  
10  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Y o u r d e v i c e  
Display  
1 — Signal strength of the cellular network  
2 — Battery charge status  
3 — Indicators  
4 — Name of the network or the operator logo  
5 — Clock  
6 — Main screen  
7 — The function of the left selection key is Go to or a shortcut to another function. See "Left selection key," p. 24.  
8 — The function of the middle selection key is Menu.  
9 — The function of the right selection key is Names or a shortcut to another function. See "Right selection key," p. 24. Operator  
variants may have an operator-specific name to access an operator-specific website.  
Power saving  
Your device has a Power saver and a Sleep mode feature in order to save battery power in the standby mode when no key of  
the device is pressed. These features may be activated. See "Display," p. 24.  
Active standby  
The active standby mode displays a list of selected device features and information that you can directly access.  
To switch active standby on or off, select Menu > Settings > Display > Active standby > Active standby mode > On or  
Off.  
In the standby mode, scroll up or down to navigate in the list, and choose Select or View. The arrows indicate that further  
information is available. To stop navigation, select Exit.  
To organize and change the active standby mode, select Options and from the available options.  
Shortcuts in the standby mode  
To access the list of dialed numbers, press the call key once. Scroll to the number or name, and press the call key to call the  
number.  
To open the web browser, press and hold 0.  
To call your voice mailbox, press and hold 1.  
Use keys as a shortcut. See "My shortcuts," p. 24.  
Indicators  
unread messages  
unsent, canceled, or failed messages  
missed call  
/
Your phone is connected to the IM service, and the availability status is online or offline.  
instant messages received  
The keypad is locked.  
The phone does not ring for an incoming call or text message.  
The alarm clock is activated.  
The countdown timer is running.  
The stopwatch is running in the background.  
11  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
C a l l f u n c t i o n s  
/
/
The phone is registered to the GPRS or EGPRS network.  
A GPRS or EGPRS connection is established.  
/
The GPRS or EGPRS connection is suspended (on hold).  
A Bluetooth connection is active.  
/
A push-to-talk connection is active or suspended.  
If you have two phone lines, the second phone line is selected.  
All incoming calls are diverted to another number.  
The loudspeaker is activated, or the music stand is connected to the device.  
Calls are limited to a closed user group.  
The timed profile is selected.  
/
/
A headset, handsfree, or loopset is connected to the device.  
Flight mode  
You can deactivate all radio frequency functions and still have access to offline games, calendar, and phone numbers.  
Use the flight mode in radio sensitive environments—on board aircraft or in hospitals. When the flight mode is active,  
is  
shown.  
Select Menu > Settings > Profiles > Flight > Activate or Personalise to activate or set up the flight mode.  
To deactivate the flight mode, select any other profile.  
Emergency call in flight mode - Enter the emergency number, press the call key, and select Yes when Exit flight profile? is  
displayed. The phone attempts to make an emergency call.  
Warning: With the flight profile you cannot make or receive any calls, including emergency calls, or use other features  
that require network coverage. To make calls, you must first activate the phone function by changing profiles. If the  
device has been locked, enter the lock code. If you need to make an emergency call while the device is locked and in  
the flight profile, you may be also able to enter an official emergency number programmed in your device in the lock  
code field and select 'Call'. The device will confirm that you are about to exit flight profile to start an emergency call.  
Keypad lock (keyguard)  
To prevent accidental keypresses, select Menu, and press * within 3.5 seconds to lock the keypad.  
To unlock the keypad, select Unlock, and press * within 1.5 seconds. If Security keyguard is set to On, enter the security code  
if requested.  
To answer a call when keyguard is on, press the call key. When you end or reject the call, the keypad automatically locks.  
Further features are Automatic keyguard and Security keyguard. See "Phone," p. 27.  
When the keyguard is on, calls may be possible to the official emergency number programmed into your device.  
Functions without a SIM card  
Several functions of your device may be used without installing a SIM card (for example, the data transfer with a compatible PC  
or another compatible device). Some functions appear dimmed in the menus and cannot be used.  
4.  
Call functions  
Make a call  
Number dialing  
1. Enter the phone number, including the area code.  
For international calls, press * twice for the international prefix (the + character replaces the international access code), enter  
the country code, the area code without the leading 0, if necessary, and the phone number.  
2. To call the number, press the call key. To adjust the volume in a call, press the volume key up or down.  
3. To end the call or to cancel the call attempt, press the end key.  
12  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
W r i t e t e x t  
You can search for a name or phone number that you have saved in Contacts. See "Search for a contact," p. 22. Press the call  
key to call the number.  
To access the list of dialed numbers, press the call key once in the standby mode. To call the number, select a number or name,  
and press the call key.  
Dialing shortcuts  
Assign a phone number to one of the number keys, 2 to 9. See "Dialing shortcuts," p. 23.  
Call the number in one of the following ways:  
Press a number key, then the call key.  
OR  
If Speed dialling is set to On, press and hold a number key until the call begins.  
Further details are described in Speed dialling. See "Call," p. 27.  
Enhanced voice dialing  
You can make a phone call by saying the name that is saved in the contact list of the device.  
Voice commands are language-dependent. Set the Voice recognition language before using voice dialing. See  
Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely  
upon voice dialing in all circumstances.  
1. In the standby mode, press and hold the right selection key or the volume down key. A short tone sounds, and Speak  
now is displayed.  
2. Speak the name of the contact you want to dial clearly. If the voice recognition is successful, a list with matches is shown.  
The device plays the voice command of the first match on the list. If it is not the correct command, scroll to another entry.  
Using voice commands to carry out a selected device function is similar to voice dialing. See "Voice commands," p. 25.  
Answer or reject a call  
To answer an incoming call, press the call key. To end the call, press the end key.  
To reject an incoming call, press the end key. To mute the ringing tone, select Silence.  
To answer a waiting call during an active call (network service), press the call key. The first call is put on hold. To end the active  
call, press the end key. You may also activate the Call waiting function. See "Call," p. 27.  
Options during a call  
Many of the options that you can use during a call are network services. For availability, contact your service provider.  
During a call, select Options and from the following options:  
Call options are Mute or Unmute, Contacts, Menu, Lock keypad, Record, Voice clarity, Loudspeaker or Handset.  
Network options are Answer or Reject, Hold or Unhold, New call, Add to conference, End call, End all calls, and the following:  
Send DTMF — to send tone strings  
Swap — to switch between the active call and the call on hold  
Transfer — to connect a call on hold to an active call and disconnect yourself  
Conference — to make a conference call  
Private call — to have a private discussion in a conference call  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
5.  
Write text  
Text modes  
To enter text (for example, when writing messages) you can use traditional or predictive text input.  
When you write text, press and hold Options to toggle between traditional text input, indicated by  
, and predictive text  
input, indicated by  
. Not all languages are supported by predictive text input.  
13  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
N a v i g a t e t h e m e n u s  
The character cases are indicated by  
,
, and  
. To change the character case, press #. To change from the letter to number  
mode, indicated by  
, press and hold #, and select Number mode. To change from the number to the letter mode, press and  
hold #.  
To set the writing language, select Options > Writing language.  
Traditional text input  
Press a number key, 2 to 9, repeatedly until the desired character appears. The available characters depend on the selected  
writing language.  
If the next letter you want is located on the same key as the present one, wait until the cursor appears and enter the letter.  
To access the most common punctuation marks and special characters, repeatedly press the number key 1 or press * to select  
a special character.  
Predictive text input  
Predictive text input is based on a built-in dictionary to which you can also add new words.  
1. Start writing a word, using the keys 2 to 9. Press each key only once for one letter.  
2. When you finish writing the word and it is correct, to confirm it by adding a space, press 0.  
If the word is not correct, press * repeatedly, and select the word from the list.  
If the ? character is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the  
dictionary, select Spell. Enter the word using traditional text input, and select Save. To write compound words, enter the  
first part of the word, and press the scroll key right to confirm it. Write the last part of the word, and confirm the word.  
3. Start writing the next word.  
6.  
Navigate the menus  
The device offers you an extensive range of functions that are grouped into menus.  
1. To access the menu, select Menu.  
2. Scroll through the menu, and select an option (for example, Settings).  
3. If the selected menu contains further submenus, select one (for example, Call).  
4. If the selected menu contains further submenus, repeat step 3.  
5. Select the setting of your choice.  
6. To return to the previous menu level, select Back.  
To exit the menu, select Exit.  
To change the menu view, select Options > Main menu view > List, Grid, Grid with labels, or Tab.  
To rearrange the menu, scroll to the menu to be moved, and select Options > Organise > Move. Scroll to where you want to  
move the menu, and select OK. To save the change, select Done > Yes.  
7.  
Messaging  
You can read, write, send, and save text, multimedia, e-mail, audio, and flash messages and postcards. All messages are organized  
into folders.  
Text messages  
Your device supports the sending of text messages beyond the character limit for a single message. Longer messages are sent  
as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks,  
and characters from some language options, take up more space, limiting the number of characters that can be sent in a single  
message.  
With the short message service (SMS) you can send and receive text messages and receive messages that can contain pictures  
(network service).  
Before you can send any text message, you must save your message center number. See "Message settings," p. 20.  
To check SMS e-mail service availability and to subscribe to the service, contact your service provider. You can save an e-mail  
address in Contacts. See "Save details," p. 21.  
14  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
M e s s a g i n g  
Write and send a text message  
1. Select Menu > Messaging > Create message > Text message.  
2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select  
Add.  
3. For an SMS e-mail, enter a subject in the Subject: field.  
4. Write your message in the Message: field.  
An indicator at the top of the display shows the total number of characters left and the number of messages needed for  
sending. For example, 673/2 means that there are 673 characters left and that the message will be sent as a series of 2  
messages.  
5. To send the message, select Send. See "Message sending process," p. 16.  
Read and reply to a text message  
1. To view a received message, select Show. To view it later, select Exit.  
2. To read the message later, select Menu > Messaging > Inbox.  
3. To reply to a message, select Reply and the message type.  
4. Create the reply message.  
is shown if you have unread messages in the inbox.  
5. To send the message, select Send. See "Message sending process," p. 16.  
Multimedia messages  
Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may  
vary depending on the receiving device.  
The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it  
smaller so that it can be sent by MMS.  
A multimedia message can contain text and objects such as images, sound clips, or video clips.  
To check availability and to subscribe to the multimedia messaging service (MMS), contact your service provider. See "Message  
Write and send a multimedia message  
1. Select Menu > Messaging > Create message > Multimedia.  
2. Create your message.  
Your device supports multimedia messages that contain several pages (slides). A message can contain a calendar note and  
a business card as attachments. A slide can contain text, one image, and one sound clip; or text and a video clip. To insert a  
slide in the message, select New; or select Options > Insert > Slide. To insert a file in the message, select Insert.  
3. To view the message before sending it, select Options > Preview.  
4. To send the message, select Send.  
5. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select  
Add.  
6. For an SMS e-mail, enter a subject in the Subject: field.  
7. To send the message, select Send. See "Message sending process," p. 16.  
Write and send a multimedia plus message  
Any content can be added to the multimedia plus message. Such content might be images, video clips, sound clips, business  
cards, calendar notes, themes, streaming links, or even unsupported files (for example, files received with an e-mail).  
1. Select Menu > Messaging > Create message > Multimedia plus.  
2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select  
Add.  
3. Enter a subject and write your message.  
4. To insert a file in the message, select Insert or Options > Insert and the file type.  
5. To view the message before sending it, select Options > Preview.  
6. To send the message, select Send. See "Message sending process," p. 16.  
Read and reply to a multimedia message  
Important: Exercise caution when opening messages. E-mail messages or multimedia message objects may contain  
malicious software or otherwise be harmful to your device or PC.  
15  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
M e s s a g i n g  
1. To view the received message, select Show. To view it later, select Exit.  
2. To view the whole message if the received message contains a presentation, select Play. To view the files in the presentation  
or the attachments, select Options > Objects or Attachments.  
3. To reply to the message, select Options > Reply and the message type.  
4. Create the reply message.  
5. To send the message, select Send. See "Message sending process," p. 16.  
Message sending process  
To send the message, select Send. The phone saves the message in the Outbox folder, and the sending starts.  
Note: Your device may indicate that your message was sent to the message center number programmed into your  
device. Your device may not indicate whether the message is received at the intended destination. For more details  
about messaging services, contact your service provider.  
If an interruption occurs while the message is being sent, the phone tries to resend the message a few times. If these attempts  
fail, the message remains in the Outbox folder. To cancel the sending of the messages in the Outbox folder, scroll to the desired  
message, and select Options > Cancel sending.  
Postcards  
With the postcard messaging service (network service), create and send postcards that may contain an image and a greeting  
text. The postcard is sent to the service provider using multimedia messaging. The service provider prints the postcard and  
sends it to the postal address given with the message. MMS must be activated before this service can be used.  
Before you can use the postcard service, you must subscribe to the service. To check the availability and costs and to subscribe  
to the service, contact your service provider.  
To send a postcard, select Menu > Messaging > Create message > Postcard. Fill in the address; mandatory editor fields  
are marked by a *. Scroll to the image field, select Insert and an image from the gallery, or New image to insert a recent image;  
then write your greeting text. To send the message, select Send.  
Flash messages  
Flash messages are text messages that are instantly displayed upon reception. Flash messages are not automatically saved.  
Write a flash message  
Select Menu > Messaging > Create message > Flash message. Enter the recipient’s phone number and write your message.  
The maximum length of a flash message is 70 characters. To insert a blinking text into the message, select Options > Insert  
blink char. to set a marker. The text after the marker blinks. To end the blinking text range, insert a second marker.  
Read and reply to a flash message  
A received flash message is indicated with Message: and a few words from the beginning of the message.  
To read the message, select Read.  
To extract numbers and addresses from the current message, select Options > Use detail.  
To save the message, select Save and the folder in which you want to save it.  
Nokia Xpress audio messaging  
You can use the MMS to create and send an audio message in a convenient way. MMS must be activated before you can use  
audio messages.  
Create a message  
1. Select Menu > Messaging > Create message > Audio message. The voice recorder opens. See "Voice  
2. Speak your message.  
3. Enter one or more phone numbers in the To: field, or select Add to retrieve a number.  
4. To send the message, select Send.  
Listen to a message  
To open a received audio message, select Play.  
If more than one message is received, select Show > Play.  
16  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
M e s s a g i n g  
To listen to the message later, select Exit.  
Memory full  
When you receive a message, and the memory for the messages is full, Memory full. Unable to receive msgs. is displayed.  
To delete old messages, select OK > Yes and the folder. Scroll to the desired message, and select Delete.  
To delete more messages, select Mark. Mark all the messages you want to delete, and select Options > Delete marked.  
Folders  
The device saves received messages in the Inbox folder. Messages that have not yet been sent are saved in the Outbox folder.  
To set the device to save the sent messages in the Sent items folder, select Menu > Messaging > Message settings >  
General settings > Save sent messages.  
To edit and send messages that you have written and saved in the drafts folder, select Menu > Messaging > Drafts.  
You can move messages to the Saved items folder. To organize your Saved items subfolders, select Menu > Messaging >  
Saved items.  
To add a folder, select Options > Add folder.  
To delete or rename a folder, scroll to the desired folder, and select Options > Delete folder or Rename folder.  
To create a new template, save a message as a template, or access the template list, and select Menu > Messaging > Saved  
items > Templates.  
E-mail application  
The e-mail application uses a packet data connection (network service) to allow you to access your e-mail account. This e-mail  
application is different from the SMS e-mail function. To use the e-mail function on your device, you need a compatible e-mail  
system.  
You can write, send, and read e-mail with your device. Your device supports POP3 and IMAP4 e-mail servers. This application  
does not support keypad tones.  
Before you can send and retrieve any e-mail messages, you must obtain a new e-mail account or use your current account. To  
check the availability of your e-mail account, contact your e-mail service provider.  
Check your e-mail settings with your e-mail service provider. You may receive the e-mail configuration settings as a configuration  
To activate the e-mail settings, select Menu > Messaging > Message settings > E-mail messages. See "E-mail  
Setting wizard  
The setting wizard starts automatically if no e-mail settings are defined in the phone.  
To enter the settings manually, select Menu > Messaging > E-mail > Options > Manage accounts > Options > New.  
The options for Manage accounts allow you to add, delete, and change the e-mail settings. Make sure that you have defined  
the correct preferred access point for the operator. See "Configuration," p. 28.  
The e-mail application requires an internet access point without a proxy. WAP access points normally include a proxy and do  
not work with the e-mail application.  
Write and send an e-mail  
You can write your e-mail message before connecting to the e-mail service; or connect to the service first, then write and send  
your e-mail.  
1. Select Menu > E-mail > Write new e-mail.  
2. If more than one e-mail account is defined, select the account from which you want to send the e-mail.  
3. Enter the recipient’s e-mail address, write the subject, and enter the e-mail message. To attach a file from Gallery, select  
Options > Attach file.  
4. To send the e-mail message, select Send > Send now.  
To save the e-mail in the Outbox folder to be sent later, select Send > Send later.  
To edit or continue writing your e-mail later, select Options > Save as draft. The e-mail is saved in Outboxes > Drafts.  
To send the e-mail later, select Menu > Messaging > E-mail > Options > Send now or Send/check e-mail.  
17  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
M e s s a g i n g  
Download e-mail  
To download e-mail messages that have been sent to your e-mail account, select Menu > Messaging > E-mail > Check new  
e-mail. If more than one e-mail account is defined, select the account from which you want to download the e-mail. The e-mail  
application only downloads e-mail headers at first. Select Back > Inboxes, the account name, the new message, and  
Retrieve to download the complete e-mail message.  
To download new e-mail messages and to send e-mail that has been saved in the Outbox folder, select Options > Send/check  
e-mail.  
Read and reply to e-mail  
Important: Exercise caution when opening messages. E-mail messages or multimedia message objects may contain  
malicious software or otherwise be harmful to your device or PC.  
1. Select Menu > Messaging > E-mail > Inboxes, the account name, and the desired message.  
2. To reply to an e-mail, select Reply > Original text or Empty message. To reply to many, select Options > Reply to all.  
Confirm or edit the e-mail address and subject; then write your reply.  
3. To send the message, select Send > Send now.  
E-mail folders  
Your phone saves e-mail that you have downloaded from your e-mail account in Inboxes. Inboxes contains the following  
folders: “Account name” for incoming e-mail, Archive for archiving e-mail, Custom 1Custom 3 for sorting e-mail, Junk where  
all spam e-mail is stored, Drafts for saving unfinished e-mail, Outbox for saving e-mail that has not been sent, and Sent  
items for saving e-mail that has been sent.  
To manage the folders and their e-mail content, select Options to view the available options of each folder.  
Spam filter  
The spam filter allows you to put specific senders on a black or white list. Black list sender messages are filtered toJunk. Unknown  
and white list sender messages are downloaded into the account inbox.  
To activate and define a spam filter, select Options > Spam filter > Settings in the main e-mail idle screen.  
To blacklist a sender, select the e-mail message in the Inboxes folder and Options > Blacklist sender.  
Instant messages  
Note: Depending on your IM service, you may not have access to all of the features described in this guide.  
With instant messaging (IM) (network service) you can send short, simple text messages to online users. You have to subscribe  
to a service and register with the IM service you want to use. For more information about signing up for IM services, contact  
your service provider.  
To set the required settings for the IM service, use the option Connect. settings. See "Access," p. 18.  
The icons and texts on the display may vary, depending on the IM service.  
Access  
Select Menu > Messaging > Instant messages. Instant messages may be replaced by another term depending on the  
service provider. If more than one set of connection settings for IM service is available, select the one you want.  
Select from the following options:  
Login — to connect to the IM service. To set the phone to automatically connect to the IM service when you switch on the  
phone, in the login session, select Automatic login: > On.  
Saved convers. — to view, erase, or rename the conversations that you saved during an IM session  
Connect. settings — to edit the settings needed for messaging and presence connection  
Connect  
To connect to the service, access the instant messages menu, select the IM service, if needed, and Login.  
To disconnect from the IM service, select Options > Logout.  
Sessions  
When connected to the service, your status, as seen by others, is shown in a status line: Status: Online, My status: Busy, or  
Status: App. off. To change your own status, select Change.  
18  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
M e s s a g i n g  
Below the status line there are three folders containing your contacts that show their status: Conversations, Online (), and  
Offline (). To expand the folder, scroll to it, and select Expand (or scroll right).  
To collapse the folder, select Collapse (or scroll left).  
Conversations — shows the list of new and read instant messages or invitations to IM during the active IM session:  
indicates a new group message  
indicates a read group message  
indicates a new instant message  
indicates a read instant message  
indicates an invitation  
The icons and texts on the display depends on the IM service.  
Online () — shows the number of contacts that are online  
Offline () — shows the number of contacts that are offline  
To start a conversation, expand the online or the offline folder, scroll to the contact with whom you want to chat, and select  
Chat. To answer an invitation or reply to a message, expand the Conversations folder, scroll to the contact to whom you  
want to chat, and select Open.  
Groups > Public groups — List of bookmarks to public groups provided by the service provider (not visible if groups are not  
supported by the network). To start an IM session with a group, scroll to a group, and select Join. Enter the screen name that  
you want to use as your nickname in the conversation. When you have successfully joined the group conversation, you can  
start a group conversation. You can create a private group. See "Groups," p. 19.  
Search > Users or Groups — to search for other IM users or public groups on the network by phone number, screen name,  
e-mail address, or name. If you select Groups, you can search for a group by a member in the group, group name, topic, or  
ID.  
Options > Chat or Join group — to start the conversation when you have found the user or the group that you want  
Accept or reject an invitation  
If you receive a new invitation, to read it, select Read. If more than one invitation is received, select an invitation and Open. To  
join the private group conversation, select Accept, and enter the screen name you want to use as your nickname. To reject or  
delete the invitation, select Options > Reject or Delete.  
Read an instant message  
If you receive a new message that is not a message associated with an active conversation, New instant message is displayed.  
To read it, select Read. If more than one message is received, select a message and Open.  
New messages received during an active conversation are held inInstant messages > Conversations. If you receive a message  
from someone who is not in IM contacts, the sender ID is displayed. To save a new contact that is not in the phone memory,  
select Options > Save contact.  
Participate in a conversation  
To join or start an IM session, write your message, and select Send.  
If you receive a new message during a conversation from a person who is not taking part in the current conversation,  
is  
displayed, and the phone sounds an alert tone. Write your message, and select Send. Your message is displayed, and the reply  
message is displayed below your message.  
Add IM contacts  
When connected to the IM service, in the IM main menu, select Options > Add contact > By mobile number, Enter ID  
manually, Search from serv., or Copy from server (depending on the service provider). To start a conversation, scroll to a  
contact, and select Chat.  
Block or unblock messages  
When you are in a conversation and want to block messages, select Options > Block contact.  
To block messages from a specific contact in your contacts list, scroll to the contact in Conversations, and select Options >  
Block contact > OK.  
To unblock a contact, in the IM main menu, select Options > Blocked list. Scroll to the contact you want to unblock, and select  
Unblock > OK.  
Groups  
You can use the public groups provided by the service provider or create your own private groups for an IM conversation.  
19  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
M e s s a g i n g  
You can bookmark public groups that your service provider may maintain. Connect to the IM service, and select Groups >  
Public groups. Select a group and Join. If you are not in the group, enter your screen name as your nickname for the group.  
To delete a group from your list, select Options > Delete group.  
To search for a group, select Groups > Public groups > Search groups.  
To create a private group, connect to the IM service, and, from the main menu, select Options > Create group. Enter the name  
for the group and the screen name that you want to use as your nickname. Mark the private group members in the contacts  
list, and write an invitation.  
Voice messages  
The voice mailbox is a network service to which you may need to subscribe. For more information, contact your service provider.  
To call your voice mailbox, select Menu > Messaging > Voice messages > Listen to voice messages.  
To enter, search for, or edit your voice mailbox number, select Voice mailbox number.  
If supported by the network,  
indicates new voice messages. To call your voice mailbox number, select Listen.  
Info messages  
You can receive messages on various topics from your service provider (network service). For more information, contact your  
service provider.  
Select Menu > Messaging > Info messages and from the available options.  
Service commands  
Service commands allow you to write and send service requests (USSD commands) to your service provider, such as activation  
commands for network services.  
To write and send the service request, select Menu > Messaging > Service commands. For details, contact your service  
provider.  
Delete messages  
Delete a single message, all messages, or a folder.  
To delete messages, select Menu > Messaging > Delete messages > By message to delete a single message, By folder to  
delete all messages from a folder, or All messages.  
SIM messages  
SIM messages are specific text messages that are saved to your SIM card.  
You can copy or move those messages from the SIM to the phone memory, but not vice versa.  
To read SIM messages, select Menu > Messaging > Options > SIM messages.  
Message settings  
General settings  
General settings are common for text and multimedia messages.  
Select Menu > Messaging > Message settings > General settings and from the following options:  
Save sent messages — Select Yes to save the sent messages in the Sent items folder.  
Overwriting in Sent items — Select Allowed to overwrite old sent messages with the new ones when the message memory  
is full. This setting is shown only if you select Save sent messages > Yes.  
Font size — Select the font size used in messages.  
Graphical smileys — Select Yes to set the device to replace character-based smileys with graphical ones.  
Text messages  
The text message settings affect the sending, receiving, and viewing of text and SMS e-mail messages.  
Select Menu > Messaging > Message settings > Text messages and from the following options:  
Delivery reports — Select Yes to ask the network to send delivery reports about your messages (network service).  
Message centres — Select Add centre to set the phone number and name of the message center that is required for sending  
text messages. You receive this number from your service provider.  
Message centre in use — to select the message center in use.  
20  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
C o n t a c t s  
E-mail message centres — Select Add centre to set the phone numbers and name of the e-mail center for sending SMS e-  
mail.  
E-mail centre in use — to select the SMS e-mail message center in use  
Message validity — to select the length of time for which the network attempts to deliver your message  
Messages sent via — to select the format of the messages to be sent: Text, Paging, or Fax (network service)  
Use packet data — Select Yes to set GPRS as the preferred SMS bearer.  
Character support — Select Full to select all characters in the messages to be sent as viewed. If you select Reduced,  
characters with accents and other marks may be converted to other characters.  
Reply via same centre — Select Yes to allow the recipient of your message to send you a reply using your message center  
(network service).  
Multimedia messages  
The message settings affect the sending, receiving, and viewing of multimedia messages.  
You may receive the configuration settings for multimedia messaging as a configuration message. See "Configuration setting  
service," p. 7. You can also enter the settings manually. See "Configuration," p. 28.  
Select Menu > Messaging > Message settings > Multimedia msgs. and from the following options:  
Delivery reports — Select Yes to ask the network to send delivery reports about your messages (network service).  
Image size (multimedia plus) — to set the image size in multimedia plus messages  
Image size (multimedia) — to set the image size in multimedia messages  
Default slide timing — to define the default time between slides in multimedia messages  
Allow multimedia reception — Select Yes or No to receive or block the multimedia message. If you select In home  
network, you cannot receive multimedia messages when outside your home network. The default setting of the multimedia  
message service is generally In home network. The availability of this menu depends on your phone.  
Incoming multi- media messages — to allow the reception of multimedia messages automatically, manually after being  
prompted, or to reject the reception. This setting is not shown if Allow multimedia reception is set to No.  
Allow adverts — to receive or reject advertisements. This setting is not shown if Allow multimedia reception is set to  
No, or Incoming multi- media messages is set to Reject.  
Configuration settings — Select Configuration to display the configurations that support multimedia messaging. Select a  
service provider, Default, or Personal config. for multimedia messaging. Select Account and an MMS account contained in  
the active configuration settings.  
E-mail messages  
The settings affect sending, receiving, and viewing e-mail. You may receive the settings as a configuration message. See  
Select Menu > Messaging > Message settings > E-mail messages to display the options.  
8.  
Contacts  
You can save names and phone numbers (contacts) in the device memory and in the SIM card memory.  
The device memory can save contacts with additional details, such as various phone numbers and text items. You can also save  
an image for a limited number of contacts.  
The SIM card memory can save names with one phone number attached to them. The contacts saved in the SIM card memory  
are indicated by  
.
Save names and phone numbers  
Names and numbers are saved in the used memory.  
To save a name and phone number, select Menu > Contacts > Names > Options > Add new contact.  
Save details  
In the device memory you can save different types of phone numbers, a tone or a video clip, and short text items for a contact.  
The first number you save is automatically set as the default number and is indicated with a frame around the number type  
indicator (for example, ). When you select a name from contacts (for example, to make a call), the default number is used  
unless you select another number.  
Make sure that the memory in use is Phone or Phone and SIM. See "Settings," p. 22.  
Search for the contact to add a detail, and select Details > Options > Add detail.  
21  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
C o n t a c t s  
Select from the available options.  
Settings  
These settings define where the contact information is stored, how it is displayed, and how much memory remains.  
Select Menu > Contacts > Settings and from the following options:  
Memory in use — to select the SIM card or phone memory for your contacts. Select Phone and SIM to recall names and  
numbers from both memories. In that case, when you save names and numbers, they are saved in the phone memory.  
Contacts view — to select how the names and numbers in Contacts are displayed  
Name display — to select whether the contact’s first or last name is displayed first  
Font size — to set the font size for the list of contacts  
Memory status — to view the free and used memory capacity  
Groups  
Select Menu > Contacts > Groups to arrange the names and phone numbers saved in the memory into caller groups with  
different ringing tones and group images.  
Search for a contact  
Select Menu > Contacts > Names and scroll through the list of contacts, or enter the first characters of the name to search.  
Copy or move contacts  
To copy or move a contact between the SIM card memory and the phone memory, select Menu > Contacts > Names. Select  
the contact to copy or move and Options > Copy contact or Move contact.  
To copy or move several contacts, select the first contact to copy or move and Options > Mark. Mark the other contacts, and  
select Options > Copy marked or Move marked.  
To copy or move all contacts between the SIM card memory and the phone memory, select Menu > Contacts > Copy  
contacts or Move contacts.  
The SIM card memory can save names with one phone number attached to them.  
Edit contact details  
Search for the contact, and select Details.  
To edit a name, number, or text item or to change the image, select Options > Edit.  
To change the number type, scroll to the desired number, and select Options > Change type. To set the selected number as  
the default number, select Options > Set as default.  
Delete contacts  
To delete a contact, search for the desired contact, and select Options > Delete contact.  
To delete all the contacts and the details attached to them from the phone or SIM card memory, select Menu > Contacts >  
Delete all contacts > From phone mem. or From SIM card.  
To delete a number, text item, or an image attached to the contact, search for the contact, and select Details. Scroll to the  
desired detail, and select Options > Delete and from the available options.  
Synchronize all  
Synchronize your calendar, contacts data, and notes with a remote internet server (network service). See "Synchronize from a  
Business cards  
You can send and receive a person’s contact information from a compatible device that supports the vCard standard as a business  
card.  
To send a business card, search for the contact, and select Details > Options > Send bus. card.  
When you receive a business card, select Show > Save to save the business card in the phone memory. To discard the business  
card, select Exit > Yes.  
22  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                               
C a l l l o g  
Dialing shortcuts  
Your device can dial a phone number with one keypress. The number keys, 2 to 9, can have a phone number assigned to them.  
To assign a phone number to a number key, select Menu > Contacts > Speed dials, and scroll to the number to assign as the  
shortcut for Speed dialling.  
Select Assign, or if a number has already been assigned to the key, select Options > Change.  
Select Search and the contact to assign the shortcut. If Speed dialling is off, the phone asks whether you want to activate it.  
To make a call using the shortcuts, press and hold the corresponding key. See "Dialing shortcuts," p. 13.  
Info, service, and my numbers  
Select Menu > Contacts and from one of these submenus:  
Info numbers — to call the information numbers of your service provider if the numbers are included on your SIM card  
(network service)  
Service numbers — to call the service numbers of your service provider, if the numbers are included on your SIM card  
(network service)  
My numbers — to view the phone numbers assigned to your SIM card, if the numbers are included on your SIM card.  
9.  
Call log  
The device registers your missed, received, and dialed calls if the network supports it and the device is switched on and within  
the network service area.  
To view the information on your calls, select Menu > Log > Missed calls, Received calls, or Dialled numbers.  
To view your recent missed and received calls and the dialed numbers chronologically, select Call log. To view the contacts to  
whom you most recently sent messages, select Message recipients.  
To view the approximate information on your recent communications, select Menu > Log > Call duration, Packet data  
counter, or Packet data conn. timer.  
To view how many text and multimedia messages you have sent and received, select Menu > Log > Message log.  
Note: The actual invoice for calls and services from your service provider may vary, depending on network features,  
rounding off for billing, taxes, and so forth.  
Note: Some timers, including the life timer, may be reset during service or software upgrades.  
10.  
Positioning  
The network may send you a position request (network service). Contact your service provider to subscribe and to agree upon  
the delivery of positioning information.  
To accept or reject the position request, select Accept or Reject. If you miss the request, the phone automatically accepts or  
rejects it according to what you have agreed with your network operator or service provider. The phone displays 1 missed  
position request. To view the missed positioning request, select Show.  
To view the information on the 10 most recent privacy notifications and requests or to delete them, select Menu > Log >  
Positioning > Position log > Open folder or Delete all.  
11.  
Settings  
Profiles  
Your phone has various setting groups called profiles, for which you can customize the phone tones for different events and  
environments.  
Select Menu > Settings > Profiles, the desired profile, and from the following options:  
Activate — to activate the selected profile  
Personalise — to personalize the profile. Select the setting you want to change, and make the changes.  
23  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
S e t t i n g s  
Timed — to set the profile to be active until a certain time (up to 24 hours) and set the end time. When the time set for the  
profile expires, the previous profile that was not timed becomes active.  
Themes  
A theme contains elements for personalizing your device.  
Select Menu > Settings > Themes and from the following options:  
Select theme — to set a theme. A list of folders in Gallery opens. Open the Themes folder, and select a theme.  
Theme downloads — to open a list of links to download more themes  
Tones  
You can change the tone settings of the selected active profile.  
Select Menu > Settings > Tones. You can find the same settings in the Profiles menu. See "Profiles," p. 23.  
To set the phone to only ring for calls from phone numbers that belong to a selected caller group, select Alert for.  
Select Options > Save to save the settings or Cancel to leave the settings unchanged.  
If you select the highest ringing tone level, the ringing tone reaches its highest level after a few seconds.  
Display  
Select Menu > Settings > Display and from the available options:  
Wallpaper — to add the background image in the standby mode  
Wallpaper — to add the background image in the Home screen  
Active standby — to switch the active standby mode on or off and to organize and personalize the active standby mode  
Standby mode font colour — to select the color for the texts in the standby mode  
Navigation key icons — to display the icons of the current scroll key shortcuts in the standby mode when active standby is  
off  
Screen saver — to set your device to display a screen saver. To download more screen savers, select Graphic downloads.  
To set the time after which the screen saver is activated, select Time-out.  
Power saver — to save some battery power. The date and a digital clock are displayed when no function of the device is  
used for a certain time.  
Sleep mode — to save some battery power  
Font size — to set the font size for messaging, contacts, and web pages  
Operator logo — to set your device to display or hide the operator logo  
Cell info display — to display the cell identity, if available from the network  
Time and date  
To change the clock type, time, time zone, and date settings, select Menu > Settings > Time and date > Time, Date, or  
Auto-update of date & time (network service).  
When traveling to a different time zone, select Menu > Settings > Time and date > Time > Time zone and the time zone  
of your location in terms of the time difference with respect to Greenwich mean time (GMT) or coordinated universal time (UTC).  
The time and date are set according to the time zone and enable your device to display the correct sending time of received  
text or multimedia messages.  
My shortcuts  
With personal shortcuts you get quick access to often used functions of the device.  
Left selection key  
To select a function from the list, select Menu > Settings > My shortcuts > Left selection key.  
If the left selection key is Go to to activate a function, in the standby mode, select Go to > Options and from the following  
options:  
Select options — to add a function to the shortcut list or to remove one  
Organise — to rearrange the functions on your personal shortcut list  
Right selection key  
To select a function from the list, select Menu > Settings > My shortcuts > Right selection key.  
24  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                       
S e t t i n g s  
Navigation key  
To assign other device functions from a predefined list to the navigation key (scroll key), select Menu > Settings > My  
shortcuts > Navigation key.  
Voice commands  
Call contacts and carry out device functions by speaking a voice command.  
Voice commands are language-dependent, and you must set the Voice recognition language before using voice commands.  
To select the device function to activate with a voice command, select Menu > Settings > My shortcuts > Voice  
commands and a folder. Scroll to a function.  
indicates that the voice tag is activated. To activate the voice tag, select Add.  
To play the activated voice command, select Play. See "Enhanced voice dialing," p. 13.  
To manage the voice commands, scroll to a device function, and select Options and from the following:  
Edit or Remove — to change or deactivate the voice command of the selected function  
Add all or Remove all — to activate or deactivate voice commands to all functions in the voice commands list  
Infrared  
You can set up the phone to send and receive data through its infrared (IR) port to or from a IRDA compatible phone or data  
device.  
Do not point the infrared (IR) beam at anyone's eye or allow it to interfere with other IR devices. This device is a Class 1 laser  
product.  
When sending or receiving data, ensure that the IR ports of the sending and receiving devices are pointing at each other and  
that there are no obstructions between the devices.  
To activate or deactivate the IR port of your phone, select Menu > Settings > Connectivity > Infrared.  
If the data transfer is not started within 2 minutes after the activation of the IR port, the connection is cancelled and must be  
started again.  
IR connection indicator  
When  
is shown continuously, the IR connection is activated, and your phone is ready to send or receive data through its  
IR port.  
When  
blinks, your phone is trying to connect to the other device, or a connection has been lost.  
Bluetooth  
Bluetooth wireless technology  
Bluetooth technology allows you to connect the device to a compatible Bluetooth device within 10 meters (32 feet). Since devices  
using Bluetooth technology communicate using radio waves, your device and the other devices do not need to be in direct line-  
of-sight, although the connection can be subject to interference from obstructions such as walls or from other electronic devices.  
This device is compliant with Bluetooth Specification 2.0 + EDR supporting the following profiles: generic access, network access,  
generic object exchange, advanced audio distribution, audio video remote control, hands-free, headset, object push, file transfer,  
dial-up networking, SIM access, and serial port. To ensure interoperability between other devices supporting Bluetooth  
technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine  
their compatibility with this device.  
There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.  
Features using Bluetooth technology, or allowing such features to run in the background while using other features, increase  
the demand on battery power and reduce the battery life.  
Set up a Bluetooth connection  
Select Menu > Settings > Connectivity > Bluetooth and from the following options:  
Bluetooth — Select On to activate the Bluetooth function.  
indicates that Bluetooth is activated.  
My phone's visibility — to define how your device is shown to other Bluetooth devices  
Search for audio enhancements — to search for compatible Bluetooth audio devices. Select the device that you want to  
connect to the phone.  
Active devices — to check which Bluetooth connection is currently active  
Paired devices — to search for any Bluetooth device in range. Select New to list any Bluetooth device in range. Select a  
device and Pair. Enter an agreed Bluetooth passcode of the device (up to 16 characters) to pair the device to your device. You  
25  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
S e t t i n g s  
must only give this passcode when you connect to the device for the first time. Your device connects to the other device, and  
you can start data transfer.  
My phone's name — to set the device name for Bluetooth connections  
If you are concerned about security, turn off the Bluetooth function, or set My phone's visibility to Hidden. Always accept only  
Bluetooth communication from others whom you trust.  
Packet data  
General packet radio service (GPRS) is a network service that allows mobile devices to send and receive data over an internet  
protocol (IP)-based network.  
To define how to use the service, select Menu > Settings > Connectivity > Packet data > Packet data connection and  
from the following options:  
When needed — to set the packet data connection to established when an application needs it. The connection will be  
closed when the application is terminated.  
Always online — to set the device to automatically connect to a packet data network when you switch the device on.  
You can connect the device using Bluetooth wireless technology or USB data cable connection to a compatible PC and use the  
device as a modem to enable GPRS connectivity from the PC.  
To define the settings for connections from your PC, select Menu > Settings > Connectivity > Packet data > Packet data  
settings > Active access point, and activate the access point you want to use. Select Edit active access point > Alias for  
access point, enter a name to change the access point settings, and select OK. Select Packet data access point, enter the  
access point name (APN) to establish a connection to a network, and select OK.  
Establish an internet connection by using your phone as a modem. See "Nokia PC Suite," p. 40. If you have set the settings  
both on your PC and on your device, the PC settings are used.  
Data transfer  
Synchronize your calendar, contacts data, and notes with another compatible device (for example, a mobile device), a compatible  
PC, or a remote internet server (network service).  
Your device allows data transfer with a compatible PC or another compatible device when using the device without a SIM card.  
Transfer contact list  
To copy or synchronize data from your device, the name of the device and the settings must be in the list of transfer contacts.  
If you receive data from another device (for example, a compatible mobile device), the corresponding transfer contact is  
automatically added to the list, using the contact data from the other device. Server sync and PC sync are the original items  
in the list.  
To add a new transfer contact to the list (for example, a mobile device), select Menu > Settings > Connectivity > Data  
transfer > Options > Add contact > Phone sync or Phone copy, and enter the settings according to the transfer type.  
To edit the copy and synchronize settings, select a contact from the transfer contact list and Options > Edit.  
To delete a transfer contact, select it from the transfer contact list and Options > Delete.  
Data transfer with a compatible device  
For synchronization use Bluetooth wireless technology or a cable connection. The other device must be activated for receiving  
data.  
To start data transfer, select Menu > Settings > Connectivity > Data transfer and the transfer contact from the list other  
than Server sync or PC sync.  
According to the settings, the selected data is copied or synchronized.  
Synchronize from a PC  
To synchronize data from calendar, notes, and contacts, install the Nokia PC Suite software of your device on a compatible PC.  
Use Bluetooth wireless technology or a USB data cable to connect your device with the PC and start the synchronization from  
the PC.  
Synchronize from a server  
To use a remote internet server, subscribe to a synchronization service. For more information and the settings required for this  
service, contact your service provider. You may receive the settings as a configuration message. See "Configuration setting  
To start the synchronization from your device, select Menu > Settings > Connectivity > Data transfer > Server sync.  
Synchronizing for the first time or after an interrupted synchronization may take up to 30 minutes to complete.  
26  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
S e t t i n g s  
USB data cable  
You can use the USB data cable to transfer data between the device and a compatible PC or a printer supporting PictBridge. You  
can also use the USB data cable with Nokia PC Suite.  
To activate the device for data transfer or image printing, connect the data cable. Confirm "USB data cable connected. Select  
mode." and select from the following options:  
Nokia mode — to use the cable for PC Suite  
Printing & media — to use the device with a PictBridge compatible printer or with your compatible PC  
Data storage — to connect to a PC that does not have Nokia software and use the device as a data storage device  
To change the USB mode, select Menu > Settings > Connectivity > USB data cable and the desired USB mode.  
Call  
Select Menu > Settings > Call and from the following options:  
Call divert — to divert your incoming calls (network service). You may not be able to divert your calls if some call barring  
functions are active. See "Security," p. 28.  
Voice clarity — Select Active to enhance speech intelligibility especially in noisy environments.  
Anykey answer — Select On to answer an incoming call by briefly pressing any key, except the power key, the left and right  
selection keys, or the end key.  
Automatic redial — Select On to make a maximum of 10 attempts to connect the call after an unsuccessful call attempt.  
Speed dialling — Select On to dial the names and phone numbers assigned to the number keys 2 to 9 by pressing and  
holding the corresponding number key.  
Call waiting — Select Activate to have the network notify you of an incoming call while you have a call in progress (network  
Summary after call — Select On to briefly display the approximate duration after each call.  
Send my caller ID — Select Yes to show your phone number to the person you are calling (network service). To use the  
setting agreed upon with your service provider, select Set by network.  
Line for outgoing calls — to select the phone line 1 or 2 for making calls if supported by your SIM card (network service)  
Phone  
Select Menu > Settings > Phone and from the following options:  
Language settings — To set the display language of your device, select Phone language. Automatic selects the language  
according to the information on the SIM card. To select the USIM card language, select SIM language. To set a language for  
the voice playback, select Voice recognition language. See "Enhanced voice dialing," p. 13.  
Security keyguard — To set the device to ask for the security code when you unlock the keyguard. Enter the security code,  
and select On.  
Automatic keyguard — to lock the keypad automatically after a preset time delay when the device is in the standby mode  
and no function of the device has been used. Select On, and set the time.  
Welcome note — to write the note that is shown when the device is switched on  
Flight query — The device asks every time when it is switched on whether you want to use the flight profile. With the flight  
profile, all radio connections are switched off. The flight profile should be used in areas sensitive to radio emissions.  
Phone updates — to receive software updates from your service provider (network service). This option may not be available,  
Operator selection — Select Automatic to set the device to automatically select one of the cellular networks available in  
your area. With Manual you can select a network that has a roaming agreement with your service provider.  
Confirm SIM service actions See "SIM services," p. 40.  
Help text activation — to select whether the device shows help texts  
Start-up tone — The device plays a tone when it is switched on.  
Enhancements  
This menu or the following options are shown only if the device is or has been connected to a compatible mobile enhancement.  
Select Menu > Settings > Enhancements. Select an enhancement, and depending on the enhancement, from the following  
options:  
Default profile — to select the profile that you want to be automatically activated when you connect to the selected  
enhancement  
Automatic answer — to set the device to answer an incoming call automatically after 5 seconds. If Incom. call alert: is set  
to Beep once or Off, automatic answer is off.  
Lights — to set the lights permanently On. Select Automatic to set the lights on for 15 seconds after a keypress.  
Text phone — Select Use text phone > Yes to use this setting instead of headset or loopset settings.  
27  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                             
S e t t i n g s  
Configuration  
You can configure your device with settings that are required for certain services. Your service provider may also send you these  
Select Menu > Settings > Configuration and from the following options:  
Default configuration settings — to view the service providers saved in the device. To set the configuration settings of  
the service provider as default settings, select Options > Set as default.  
Activate default in all applications — to activate the default configuration settings for supported applications  
Preferred access point — to view the saved access points. Scroll to an access point, and select Options > Details to view  
the name of the service provider, data bearer, and packet data access point or GSM dial-up number.  
Connect to service provider support — to download the configuration settings from your service provider  
Device manager settings — to allow or prevent the device from receiving software updates. This option may not be  
available, depending on your device. See "Software updates over the air," p. 28.  
Personal configuration settings — to manually add new personal accounts for various services and to activate or delete  
them. To add a new personal account if you have not added any, select Add new; otherwise, select Options > Add new.  
Select the service type, and select and enter each of the required parameters. The parameters differ according to the selected  
service type. To delete or activate a personal account, scroll to it, and select Options > Delete or Activate.  
Security  
When security features that restrict calls are in use (such as call barring, closed user group, and fixed dialing), calls may be  
possible to the official emergency number programmed into your device.  
Select Menu > Settings > Security and from the following options:  
PIN code request and UPIN code request — to set the device to ask for your PIN or UPIN code every time the device is  
switched on. Some SIM cards do not allow the code request to be turned off.  
PIN2 code request — to select whether the PIN2 code is required when using a specific device feature which is protected  
by the PIN2 code. Some SIM cards do not allow the code request to be turned off.  
Call barring service — to restrict incoming calls to and outgoing calls from your device (network service). A barring password  
is required.  
Fixed dialling — to restrict your outgoing calls to selected phone numbers if this function is supported by your SIM card.  
When the fixed dialing is on, GPRS connections are not possible except while sending text messages over a GPRS connection.  
In this case, the recipient’s phone number and the message center number must be included in the fixed dialing list.  
Closed user group — to specify a group of people whom you can call and who can call you (network service)  
Security level — Select Phone to set the device to ask for the security code whenever a new SIM card is inserted into the  
device. If you select Memory, the device asks for the security code when the SIM card memory is selected, and you want to  
change the memory in use.  
Access codes — to change the security code, PIN code, UPIN code, PIN2 code, or barring password  
Code in use — to select whether the PIN code or UPIN code should be active  
Authority certificates or User certificates — to view the list of the authority or user certificates downloaded into your  
Security module settings — to view Security module details, activate Module PIN request, or change the module PIN  
Software updates over the air  
Warning: If you install a software update, you cannot use the device, even to make emergency calls, until the  
installation is completed and the device is restarted. Be sure to back up data before accepting installation of an update.  
Your service provider may send device software updates over the air directly to your device (network service). This option may  
not be available, depending on your device.  
Software update settings  
To allow or disallow software updates, select Menu > Settings > Configuration > Device manager settings > Service  
provider software updates and the following options:  
Always allow — to perform all software downloads and updates automatically  
Always reject — to reject all software updates  
Confirm first — to perform software downloads and updates only after your confirmation (default setting)  
Request a software update  
Select Menu > Settings > Phone > Phone updates to request available software updates from your service provider. Select  
Current software details to display the current software version and check whether an update is needed. Select Download  
phone software to download and install a software update. Follow the instructions on the display.  
28  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
O p e r a t o r m e n u  
Install a software update  
If the installation was canceled after the download, select Install software update to start the installation.  
The software update may take several minutes. If there are problems with the installation, contact your service provider.  
Restore factory settings  
To reset some of the menu settings to their original values, select Menu > Settings > Restore factory sett.. Enter the security  
code.  
The names and phone numbers saved in Contacts are not deleted.  
12.  
Operator menu  
This menu lets you access a portal to services provided by your network operator. The name and the icon depend on the operator.  
For more information contact your network operator. The operator can update this menu with a service message. See "Service  
13.  
Gallery  
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied,  
modified, transferred or forwarded.  
Manage images, video clips, music files, themes, graphics, tones, recordings, and received files. These files are stored in the  
device memory or an attached memory card and may be arranged in folders.  
Your device supports an activation key system to protect acquired content. Always check the delivery terms of any content and  
activation key before acquiring them, as they may be subject to a fee.  
Folders and files  
To see the list of folders, select Menu > Gallery.  
To view the list of files in a folder, select a folder and Open.  
To see the available options of a folder or a file, select a folder or a file and Options.  
To view the folders of the memory card when moving a file, scroll to the memory card, and press the scroll key right.  
Print images  
Your device supports Nokia XPressPrint to print images that are in the .jpeg format.  
To connect your device to a compatible printer, use a data cable or send the image by Bluetooth to a printer supporting Bluetooth  
Select the image you want to print and Options > Print.  
Memory card  
Warning: Keep all memory cards out of the reach of small children.  
Use a memory card to store your multimedia files such as video clips, music tracks, sound files, images, and messaging data.  
Some of the folders in Gallery with content that the device uses (for example, Themes) may be stored on the memory card.  
To insert a memory card, see "Insert a microSD card", p. 8.  
Format the memory card  
Some supplied memory cards are preformatted; others require formatting. Consult your retailer to find out if you must format  
the memory card before you can use it. When you format a memory card, all data on the card is permanently lost.  
To format a memory card, select Menu > Gallery or Applications, the memory card folder  
, and Options > Format mem.  
card > Yes.  
When formatting is complete, enter a name for the memory card.  
29  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                             
M e d i a  
Lock the memory card  
Set a password to lock your memory card against unauthorized use.  
Selectthememorycardfolder  
andOptions > Setpassword. Thepasswordcanbeuptoeightcharacterslong. Thepassword  
is stored in your device, and you do not have to enter it again while you are using the memory card on the same device. If you  
want to use the memory card on another device, you are asked for the password.  
To delete the password, select Options > Delete password.  
Check memory consumption  
Check the memory consumption of different data groups and the available memory to install new applications or software on  
your memory card.  
Select the memory card  
and Options > Details.  
14.  
Media  
Camera and video  
This feature is available with the Nokia 3110 classic phone.  
Take images or record video clips with the built-in camera.  
Take a picture  
To use the still picture function, select Menu > Media > Camera or if the video function is on, scroll left or right.  
To take a picture in landscape format, hold the device in a horizontal position. To zoom in and out in the camera mode, scroll  
up and down or press the volume keys.  
To take a picture, select Capture. The device saves the pictures on the memory card, if available, or on the phone memory.  
Select Options to set Night mode on if the lighting is dim, Self-timer on to activate the self-timer, or Img. sequence on to  
take pictures in a fast sequence. With the highest picture size setting, three pictures are taken in a sequence; with other size  
settings, five pictures are taken.  
Select Options > Settings > Image preview time and a preview time to display the taken pictures. During the preview time,  
select Back to take another picture or Send to send the picture as a multimedia message.  
Your device supports a picture capture resolution up to 1280 x 1024 pixels.  
Record a video clip  
To activate the video function, select Menu > Media > Video; or if the camera function is on, scroll left or right.  
To start the video recording, select Record; to pause the recording, select Pause; to resume the recording, select Continue; to  
stop the recording, select Stop.  
The device saves the video clips on the memory card, if available, or in the device memory.  
Camera and video options  
To use a filter, select Options > Effects > False colours, Greyscale, Sepia, Negative, or Solarise.  
To adapt the camera to the light conditions, select Options > White balance > Auto, Daylight, Tungsten, or Fluorescent.  
To change other camera and video settings and to select the image and video storage, select Options > Settings.  
Media player  
View, play, and download files, such as images, audio, video, and animated images; or view compatible streaming videos from  
a network server (network service).  
Select Menu > Media > Media player > Open Gallery, Bookmarks, Go to address, or Media downloads to select or  
download media.  
Select Menu > Media > Media player > FF/Rew interval to set the length of the interval for fast forward or rewind.  
Configuration for a streaming service  
You may receive the configuration settings required for streaming as a configuration message from the service provider. See  
30  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                         
M e d i a  
To activate the settings, do the following:  
1. Select Menu > Media > Media player > Streaming sett. > Configuration.  
2. Select a service provider, Default, or Personal config. for streaming.  
3. Select Account and a streaming service account contained in the active configuration settings.  
Music player  
Your device includes a music player for listening to music tracks or other MP3 or AAC sound files that you have downloaded from  
the web or transferred to the device with Nokia PC Suite. See "Nokia PC Suite," p. 40.  
Music files stored in the music folder in the device memory or on the memory card are automatically detected and added to the  
music library during the startup of the device.  
To open the music player, select Menu > Media > Music player.  
Play music tracks  
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing. Do  
not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.  
Operate the music player with the virtual keys on the display.  
When you open Music player, the details of the first track on the default track list are shown. To start playing, select  
To adjust the volume level, use the volume keys of the device.  
.
To pause the playing, select  
To skip to the next track, select  
.
. To skip to the beginning of the previous track, select  
twice.  
To fast forward the current track, select and hold  
. To rewind the current track, select and hold  
. Release the key at the  
position you want.  
To stop the music player, press and hold the end key.  
Music player options  
In the music player menu, select from the following options:  
Show tracks — View all available tracks of the active track list and play the desired track. To play a track, scroll to the desired  
track, and select Play.  
Music library — View all available tracks ordered according to Artists, Albums, Genres, Composers, or Track lists. Select  
Update libr. to refresh the lists. To find track lists generated with the Nokia Music Manager, select Track lists > My  
tracks.  
Play options — Select Random to play the tracks on the track list in random order. Select Repeat to play the current track  
or the entire track list repeatedly.  
Media equaliser — to select or define an equalizer setting  
Add to Favourites — to add the current track to the favorite track list  
Play via Bluetooth — to connect and play the tracks on an audio accessory using Bluetooth technology  
Use tone — Set the currently played music track, for example, as a ringing tone.  
Send — to send the current track by a multimedia message or using Bluetooth technology  
Web page — to access a web page associated with the currently played track, which is dimmed if no web page is available.  
Music downloads — to connect to a web service  
Memory status — to view the free and used memory capacity  
Radio  
The FM radio depends on an antenna other than the wireless device antenna. A compatible headset or enhancement  
needs to be attached to the device for the FM radio to function properly.  
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing. Do  
not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.  
This feature is available with the Nokia 3110 classic phone.  
Select Menu > Media > Radio.  
To use the graphical keys  
,
,
, or  
on the display, scroll left or right to the desired key, and select it.  
or . To change the radio frequency in 0.05 MHz steps, briefly press  
Save radio frequencies  
1. To start the search, select and hold  
or  
.
31  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
P u s h t o t a l k  
2. To save a frequency to a memory location, 1 to 9, press and hold the corresponding number key. To save a frequency to a  
memory location from 10 to 20, press briefly 1 or 2, and press and hold the desired number key, 0 to 9.  
3. Enter the name of the radio station.  
Listen to the radio  
Select Menu > Media > Radio. To scroll to the desired frequency, select  
or , or press the headset key. To select a radio  
station, briefly press the corresponding number keys. To adjust the volume, press the volume keys.  
Select from the following options:  
Switch off — to turn off the radio  
Loudspeaker or Headset — to listen to the radio using the loudspeaker or headset. Keep the headset connected to the  
device. The lead of the headset functions as the radio antenna.  
Mono output or Stereo output — to listen to the radio in monophonic sound or in stereo  
Stations — to select the list of saved stations. To delete or rename a station, scroll to the desired station, and select  
Options > Delete station or Rename.  
Search all stations — to automatically search the available stations at your location  
Set frequency — to enter the frequency of the desired radio station  
Station directory — to access a website with a list of radio stations  
Visual Radio — to start visual radio manually  
Enable visual serv. — Select Automatically to set whether Visual Radio (network service) automatically starts when you  
turn on the radio. Some radio stations may send text or graphical information that you can view using the Visual Radio  
application. To check the availability and costs, contact your service provider.  
When an application using a packet data or HSCSD connection sends or receives data, it may interfere with the radio.  
Voice recorder  
Record speech, sound, or an active call, and save them in Gallery. This is useful when recording a name and phone number to  
write down later.  
Record sound  
1. Select Menu > Media > Recorder. To use the graphical keys  
,
, or  
on the display, scroll left or right to the desired  
key, and select it.  
2. To start the recording, select . To start the recording during a call, select Options > Record. While recording a call, all  
parties to the call hear a faint beeping. When recording a call, hold the device in the normal position near to your ear. To  
pause the recording, select  
.
3. To end the recording, select . The recording is saved in Gallery > Recordings.  
Select from the following Options:  
Play last recorded — to listen to the latest recording  
Send last recorded — to send the last recording  
Recordings list — Select Recordings to see the list of recordings in Gallery  
Equalizer  
Control the sound when using the music player by amplifying or diminishing frequency bands.  
Select Menu > Media > Equaliser.  
To activate a set, scroll to one of the equalizer sets, and select Activate.  
To view, edit, or rename a selected set, select Options > View, Edit, or Rename.  
Not all sets can be edited or renamed.  
Stereo widening  
Stereo widening enhances the audio output of the device when you are using a stereo headset by enabling a wider stereo sound  
effect.  
To change the setting, select Menu > Media > Stereo widening.  
15.  
Push to talk  
Push to talk (PTT) is a two-way radio service available over a GPRS cellular network (network service).  
32  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
P u s h t o t a l k  
You can use PTT to have a conversation with one person or with a group of people (channel) having compatible devices. While  
you are connected to the PTT service, you can use the other functions of the device.  
To check availability, costs, additional features and to subscribe to the service, contact your service provider. Roaming services  
may be more limited than for normal calls. This feature may not be available, depending on your phone.  
Before you can use the PTT service, you must define the required PTT service settings. See "PTT settings," p. 34. See  
PTT channels  
PTT channel types  
A PTT channel comprises a group of people (for example, friends or a work team) who joined the channel after they were invited.  
When you call a channel, all members joined to the channel hear the call simultaneously.  
In a Public channel, every channel member can invite other persons; in a Private channel, only the channel creator can invite  
others.  
You can set the status of each channel to Active or Inactive.  
The number of active channels and the number of members per channel is limited. Contact your service provider for details.  
Create a channel  
To add a channel, select Menu > Push to talk > Add channel, and enter the settings in the form fields.  
To send an invitation to the channel, select Yes. To send further invitations, select Menu > Push to talk > Channel list, a  
channel, and Options > Send invitation.  
Switch PTT on and off  
To connect to the PTT service, select Menu > Push to talk > Switch PTT on. indicates the PTT connection. indicates that  
the service is temporarily unavailable. If you have added channels to the phone, you are automatically joined to the active  
channels.  
To disconnect from the PTT service, select Switch PTT off.  
You may assign a default function to the PTT (volume up) key to open the channel list, the contacts list, or a single channel or  
Make and receive a PTT call  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
To make a channel call, a one-to-one call, or a call to multiple recipients, you must hold the PTT (volume up) key as long as you  
talk. To listen to the response, release the PTT (volume up) key.  
Check the login status of your contacts in Menu > Push to talk > Contacts list:  
- person available,  
- person unknown,  
- person does not want to be disturbed, but can receive callback request,  
- person has PTT switched off.  
This service depends on your network operator and is only available for subscribed contacts. To subscribe a contact, select  
Options > Subscribe contact, or if one or more contacts are already marked, Subscribe marked.  
Make a channel call  
To make a call to a channel, select Channel list in the PTT menu, scroll to the desired channel, and press and hold the PTT  
(volume up) key.  
Make a one-to-one call  
To start a one-to-one call, select Menu > Contacts > Names, or Menu > Push to talk > Callback inbox, Channel list, or  
Contacts list. Select a contact, a member, or a nickname, and press and hold the PTT (volume up) key.  
Make a PTT call to multiple recipients  
You can select multiple PTT contacts from the contact list.  
1. Select Menu > Push to talk > Contacts list, and mark the desired contacts.  
2. Press and hold the PTT (volume up) key to start the call. The participating contacts are shown on the display as soon as they  
join the call.  
3. Press and hold the PTT (volume up) key to talk to them. Release the PTT (volume up) key to hear the response.  
4. Press the end key to terminate the call.  
33  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
A p p l i c a t i o n s  
Receive a PTT call  
A short tone notifies you of an incoming PTT call, which you can accept or reject.  
When you press and hold the PTT (volume up) key while the caller is talking, you hear a queuing tone, and Queuing is displayed.  
Wait for the other person to finish; then you can talk immediately.  
Callback requests  
Send a callback request  
If you make a one-to-one call and do not get a response, you can send a callback request from following lists:  
Menu > Contacts > Names  
Menu > Push to talk > Callback inbox, Channel list, or Contacts list  
Select a contact, a member, or a nickname and Options > Send PTT callback.  
Respond to a callback request  
When someone sends you a callback request, Callback request received is displayed in the standby mode. To open the Callback  
inbox, select View. The list of nicknames of the persons who have sent you callback requests is shown. To make a one-to-one  
call, select the desired request, and press and hold the PTT (volume up) key.  
Add a one-to-one contact  
You can save the names of persons to whom you often make one-to-one calls in the following ways:  
To add a PTT address to a name in Contacts, search for the desired contact, and select Details > Options > Add detail >  
PTT address. A contact appears in the PTT contact list only if you enter a PTT address.  
To add a contact to the PTT contacts list, select Menu > Push to talk > Contacts list > Options > Add contact.  
To add a contact from the channel list, connect to the PTT service, select Channel list, and scroll to the desired channel. Select  
Members, scroll to the member whose contact information you want to save, and select Options.  
To add a new contact, select Save as. To add a PTT address to a name in Contacts, select Add to contact.  
PTT settings  
Select Menu > Push to talk > PTT settings and from the following options:  
1 to 1 calls — Select On to allow the reception of incoming one-to-one calls. To set the device to first notify you of incoming  
one-to-one calls with a ringing tone, select Notify.  
PTT key default function — to set the PTT (volume up) key to one of the following functions: Open contact list, Open  
channel list, or Call contact/group. Select a contact, a group, or Call PTT channel; and select a channel. When you press  
and hold the PTT (volume up) key, the selected function is performed.  
Show my login status — to enable or disable the sending of the login status  
PTT status in startup — Select Yes or Ask first to automatically connect to the PTT service when you switch the device on.  
Push to talk when abroad — to switch the PTT service on or off when the device is used outside of the home network  
Send my PTT address — Select No to hide your PTT address from channel and one-to-one calls.  
Configuration settings  
You may receive the settings for connecting to the service from your service provider. See "Configuration setting service," p. 7.  
You can also enter the settings manually. See "Configuration," p. 28.  
To select the settings for connecting to the service, select Menu > Push to talk > Config. settings.  
16.  
Applications  
You can manage applications and games. These files are stored in the device memory or an attached memory card and may be  
arranged in folders.  
You can format, lock, and unlock the memory card. See "Memory card," p. 29.  
Launch a game  
Your device software may include some games.  
Select Menu > Applications > Games. Scroll to the desired game, and select Open.  
34  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
O r g a n i z e r  
To set sounds, lights, and shakes for the game, select Menu > Applications > Options > App. settings. You can select more  
Launch an application  
Your device software may include some Java applications.  
Select Menu > Applications > Collection. Scroll to an application, and select Open.  
Application options  
Update version — to verify that a new version of the application is available for download from the web (network service)  
Web page — to provide further information or additional data for the application from an internet page (network service),  
if available  
App. access — to restrict the application from accessing the network  
Download an application  
Your device supports J2ME Java applications. Ensure that the application is compatible with your device before downloading it.  
Important: Only install and use applications and other software from trusted sources, such as applications that are  
TM  
Symbian Signed or have passed the Java Verified testing.  
You can download new Java applications and games in different ways.  
Select Menu > Applications > Options > Downloads > App. downloads; the list of available bookmarks is shown. See  
Use the Nokia Application Installer from PC Suite to download the applications to your device.  
For the availability of different services, pricing, and tariffs, contact your service provider.  
Yourdevicemayhavesomebookmarksorlinkspreinstalledforormayallowaccesstositesprovidedbythirdpartiesnotaffiliated  
with Nokia. Nokia does not endorse or assume any liability for these sites. If you choose to access them, you should take the  
same precautions, for security or content, as you would with any internet site.  
17.  
Organizer  
Alarm clock  
To set the device to sound an alarm at a desired time, select Menu > Organiser > Alarm clock.  
Set the alarm  
To set the alarm, select Alarm time, and enter the alarm time.  
To change the alarm time when the alarm time is set, select On.  
To set the device to alert you on selected days of the week, select Repeat alarm.  
To select the alarm tone, select Alarm tone. If you select the radio as an alarm tone, connect the headset to the device.  
To set a snooze time-out, select Snooze time-out and the time.  
Stop the alarm  
When the alarm time is reached, the device sounds an alert tone and flashes Alarm! and the current time on the display, even  
if the device is switched off.  
To stop the alarm, select Stop. If you let the device continue to sound the alarm for a minute or select Snooze, the alarm stops  
for the time you set in Snooze time-out, then resumes.  
If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone.  
If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to  
make and receive calls. Do not select Yes when wireless device use may cause interference or danger.  
Calendar  
Select Menu > Organiser > Calendar.  
The current day has a frame around the number. If there are any notes set for the day, the day is in bold type. To view the day  
notes, select View. To view a week, select Options > Week view. To delete all notes in the calendar, select the month or week  
view, and Options > Delete all notes.  
35  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
O r g a n i z e r  
In Settings you can set the date, time, time zone, date or time format, date separator, default view, or the first day of the week.  
In Auto-delete notes you can set the device to delete old notes automatically after a specified time.  
Make a calendar note  
Select Menu > Organiser > Calendar.  
Scroll to the date, and select Options > Make a note and one of the following note types:  
Meeting,  
Call,  
Birthday,  
Memo, or  
Reminder. Fill in the fields.  
Note alarm  
The device displays the note, and, if an alarm is set, sounds a tone. If a call note  
is displayed, press the call key to make the  
call.  
To stop the alarm and to view the note, select View. To stop the alarm for 10 minutes, select Snooze. To stop the alarm without  
viewing the note, select Exit.  
To-do list  
Save a note for a task that you must do.  
Select Menu > Organiser > To-do list. To make a note if no note is added, select Add note; otherwise, select Options >  
Add. Fill in the fields, and select Save.  
To view a note, scroll to it, and select View. While viewing a note, you can also select an option to edit the attributes. You can  
also select an option to delete the selected note and delete all the notes that you have marked as done.  
Notes  
To write and send notes, select Menu > Organiser > Notes.  
To make a note if no note is added, select Add note; otherwise, select Options > Make a note. Write the note, and select  
Save.  
Calculator  
The calculator in your device provides basic arithmetic and trigonometric functions, calculates the square and the square root,  
the inverse of a number, and converts currency values.  
Note: This calculator has limited accuracy and is designed for simple calculations.  
Calculations - Select Menu > Organiser > Calculator. When 0 is displayed on the screen, enter the first number in the  
calculation. Press # for a decimal point. Scroll to the desired operation or function, or select it from the Options. Enter the second  
number. Repeat this sequence as many times as it is necessary.  
Currency conversion - To perform a currency conversion select Options > Exchange rate. Select either of the displayed  
options. Enter the exchange rate, press # for a decimal point, and select OK. The exchange rate remains in the memory until  
you replace it with another one. To perform the currency conversion, enter the amount to be converted, and select Options >  
In domestic or In foreign.  
Note: When you change the base currency, you must enter new exchange rates because all previously set exchange  
rates are cleared.  
Timers  
Countdown timer  
1. To activate the countdown timer, select Menu > Organiser > Timer > Normal timer, enter the alarm time, and write a  
note that is displayed when the time expires. To change the countdown time, select Change time.  
2. To start the timer, select Start.  
3. To stop the timer, select Stop timer.  
Interval timer  
1. To have an interval timer with up to 10 intervals started, first enter the intervals.  
2. Select Menu > Organiser > Timer > Interval timer.  
3. To start the timer, select Start timer > Start.  
36  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
W e b  
Stopwatch  
You can measure time, take intermediate times, or take lap times using the stopwatch. During timing, the other functions of  
the device can be used.  
Using the stopwatch or allowing it to run in the background when using other features increases the demand on battery power  
and reduces the battery life.  
Select Menu > Organiser > Stopwatch and from the following options:  
Split timing — to take intermediate times. To start the time observation, select Start. Select Split every time that you want  
to take an intermediate time. To stop the time observation, select Stop. To save the measured time, select Save. To start the  
time observation again, select Options > Start. The new time is added to the previous time. To reset the time without saving  
it, select Reset.  
Lap timing — to take lap times  
Continue — to view the timing that you have set in the background  
Show last — to view the most recently measured time if the stopwatch is not reset  
View times or Delete times — to view or delete the saved times  
To set the stopwatch timing in the background, press the end key.  
18.  
Web  
Important: Use only services that you trust and that offer adequate security and protection against harmful software.  
With your device browser, access various mobile internet services that use wireless markup language (WML) or extensible  
hypertext markup language (XHTML) on their pages. Appearance may vary due to screen size. You may not be able to view all  
details of the internet pages.  
Check the availability of these services, pricing, tariffs, and instructions with your service provider.  
Set up browsing  
You may receive the configuration settings required for browsing as a configuration message from the service provider that  
offers the service that you want to use. See "Configuration setting service," p. 7.  
You can also enter all the configuration settings manually. See "Configuration," p. 28.  
Connect to a service  
Ensure that the correct configuration settings of the service are activated.  
1. To select the settings for connecting to the service, select Menu > Web > Settings > Configuration settings.  
2. Select Configuration. Only the configurations that support browsing service are shown. Select a service provider, Default,  
or Personal config. for browsing. See "Set up browsing," p. 37.  
3. Select Account and a browsing service account contained in the active configuration settings.  
4. Select Display terminal window > Yes to perform manual user authentication for intranet connections.  
Make a connection to the service in one of the following ways: Select Menu > Web > Home; or in the standby mode, press  
and hold 0.  
To select a bookmark of the service, select Menu > Web > Bookmarks.  
To select the last URL, select Menu > Web > Last web address.  
To enter the address of the service, select Menu > Web > Go to address. Enter the address of the service, and select OK.  
Browse pages  
After you make a connection to the service, you can start browsing its pages. The function of the device keys may vary in different  
services. Follow the text guides on the device display. For more information, contact your service provider.  
Browse with phone keys  
To browse through the page, scroll in any direction.  
To select an item, press the call key or Select.  
To enter letters and numbers, press 0 to 9.  
To enter special characters, press *.  
37  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
W e b  
Direct calling  
While browsing, you can make a phone call and save a name and a phone number from a page.  
Bookmarks  
You can save page addresses as bookmarks in the device memory.  
1. While browsing, select Options > Bookmarks; or in the standby mode, select Menu > Web > Bookmarks.  
2. Select a bookmark, or press the call key to connect to the page.  
3. Select Options to create and manage bookmarks.  
Yourdevicemayhavesomebookmarksorlinkspreinstalledforormayallowaccesstositesprovidedbythirdpartiesnotaffiliated  
with Nokia. Nokia does not endorse or assume any liability for these sites. If you choose to access them, you should take the  
same precautions, for security or content, as you would with any internet site.  
When you receive a bookmark, 1 bookmark received is displayed. To view the bookmark, select Show.  
Appearance settings  
While browsing, select Options > Other options > Appear. settings; or in the standby mode, select Menu > Web >  
Settings > Appearance settings and from the following options:  
Text wrapping — to select how the text is displayed  
Font size — to set the font size  
Show images — Select No to hide images on the page.  
Alerts — Select Alert for unsecure connection > Yes to set the device to alert you when a secure connection changes to  
an unsecure connection while browsing.  
Alerts — Select Alert for unsecure items > Yes to set the device to alert when a secure page contains an unsecure item.  
These alerts do not guarantee a secure connection. See "Browser security," p. 39.  
Character encoding — Select Content encoding to set the encoding for the browser page content.  
Character encoding — Select Unicode (UTF-8) web addresses > On to set the device to send a URL as UTF-8 encoding.  
Screen size — to set the screen layout to Full or Small  
JavaScript — to enable the Java scripts  
Security settings  
Cookies  
A cookie is data that a site saves in the cache memory of your device. Cookies are saved until you clear the cache memory. See  
While browsing, select Options > Other options > Security > Cookie settings; or in the standby mode, select Menu >  
Web > Settings > Security settings > Cookies.  
To allow or prevent the device from receiving cookies, select Allow or Reject.  
Scripts over secure connection  
You can select whether to run scripts from a secure page. The device supports WML scripts.  
While browsing, to allow the scripts, select Options > Other options > Security > WMLScript sett.; or in the standby mode,  
select Menu > Web > Settings > Security settings > WMLScripts over secure connection > Allow.  
Download settings  
ToautomaticallysavealldownloadedfilesinGallery, selectMenu > Web > Settings > Downloadingsettings > Automatic  
saving > On.  
Service inbox  
The device is able to receive service messages sent by your service provider (network service). Service messages are notifications  
(for example, news headlines) that may contain a text message or an address of a service.  
Service inbox access  
Select Show to access the Service inbox when you receive a service message.  
If you select Exit, the message is moved to the Service inbox.  
38  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
W e b  
To access the Service inbox later, select Menu > Web > Service inbox. To access the Service inbox while browsing, select  
Options > Other options > Service inbox. Scroll to the message you want, and select Retrieve to activate the browser and  
download the complete message.  
To display detailed information on the service notification or delete the message, select Options > Details or Delete.  
Service inbox settings  
Select Menu > Web > Settings > Service inbox settings and from the following options:  
Service messages — to set whether you want to receive service messages  
Message filter — Select On to set the device to receive service messages only from content authors approved by the service  
provider. To view the list of the approved content authors, select Trusted channels.  
Automatic connection — Select On to set the device to automatically activate the browser from the standby mode, when  
the device has received a service message. If you select Off, the device activates the browser only after you select Retrieve  
when the device has received a service message.  
Cache memory  
A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential  
information requiring passwords, empty the cache after each use. The information or services you have accessed are stored in  
the cache.  
To clear the cache while browsing, select Options > Other options > Clear the cache.  
In the standby mode, select Menu > Web > Clear the cache.  
Browser security  
Security features may be required for some services, such as online banking or shopping. For such connections you need security  
certificates and possibly a security module, which may be available on your SIM card. For more information, contact your service  
provider.  
Security module  
The security module improves security services for applications requiring a browser connection and allows you to use a digital  
signature. The security module may contain certificates as well as private and public keys. The certificates are saved in the  
security module by the service provider.  
To view or change the security module settings, select Menu > Settings > Security > Security module settings.  
Certificates  
Important: Even if the use of certificates makes the risks involved in remote connections and software installation  
considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a  
certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted  
certificates for increased security to be available. Certificates have a restricted lifetime. If "Expired certificate" or  
"Certificate not valid yet" is shown even if the certificate should be valid, check that the current date and time in your  
device are correct.  
There are three kinds of certificates: server certificates, authority certificates, and user certificates. You may receive these  
certificates from your service provider. Authority certificates and user certificates may also be saved in the security module by  
your service provider.  
To viewthe listofthe authority orusercertificatesdownloadedto yourphone, selectMenu > Settings > Security > Authority  
certificates or User certificates.  
is displayed during a connection if the data transmission between the phone and the content server is encrypted.  
The security icon does not indicate that the data transmission between the gateway and the content server (or place where  
the requested resource is stored) is secure. The service provider secures the data transmission between the gateway and the  
content server.  
Digital signature  
You can create digital signatures with your phone if your SIM card has a security module. The digital signature is the same as  
signing your name to a paper bill, contract, or other document.  
To create a digital signature, select a link on a page (for example, the title of the book you want to buy and its price). The text  
to be signed is shown and may include the amount and date.  
39  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
S I M s e r v i c e s  
Check that the header text is Read and that the digital signature icon  
is shown. If the digital signature icon does not appear,  
there is a security breach; do not enter any personal data (such as your signing PIN).  
To sign the text, read all of the text first, and select Sign. The text may not fit within a single screen. Therefore, make sure to  
scroll through and read all of the text before signing.  
Select the user certificate you want to use, and enter the signing PIN. The digital signature icon disappears, and the service may  
display a confirmation of your purchase.  
19.  
SIM services  
Your SIM card may provide additional services. You can access this menu only if it is supported by your SIM card. The name and  
contents of the menu depend on the available services.  
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider or  
other vendor.  
To set the phone to show you the confirmation messages sent between your phone and the network when you are using the  
SIM services, select Menu > Settings > Phone > Confirm SIM service actions > Yes.  
Accessing these services may involve sending messages or making a phone call for which you may be charged.  
20.  
PC connectivity  
Send and receive e-mail, and access the internet when your device is connected to a compatible PC through a Bluetooth, an  
infrared, or a data cable connection. Use your device with a variety of PC connectivity and data communications applications.  
Nokia PC Suite  
With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do notes between your device and the compatible PC  
or a remote internet server (network service). You may find more information and PC Suite on the Nokia website. See "Nokia  
Packet data, HSCSD, and CSD  
With your phone, you can use the packet data, high-speed circuit switched data (HSCSD), and circuit switched data (CSD, GSM  
data) data services. For availability and subscription to data services, contact your service provider.  
The use of HSCSD services consumes the battery faster than normal voice or data calls.  
Bluetooth  
Use Bluetooth technology to connect your compatible laptop to the internet. Your phone must have activated a service provider  
that supports internet access, and your PC has to support Bluetooth PAN (personal area network). After connecting to the network  
access point (NAP) service of the phone and pairing with your PC, your phone automatically opens a packet data connection to  
the internet. PC Suite software installation is not necessary when using the NAP service of the phone. See "Bluetooth wireless  
Data communication applications  
For information on using a data communication application, refer to the documentation provided with it.  
Making or answering phone calls during a computer connection is not recommended as it might disrupt the operation.  
For better performance during data calls, place the device on a stationary surface with the keypad facing downward. Do not  
move the device during a data call. For example, do not hold the device during a data call.  
40  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
B a t t e r y  
21.  
Battery  
Battery information  
Your device is powered by a rechargeable battery. The battery can be charged and discharged hundreds of times, but it will  
eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia  
approved batteries, and recharge your battery only with Nokia approved chargers designated for this device.  
If a replacement battery is being used for the first time or if the battery has not been used for a prolonged period, it may be  
necessary to connect the charger, then disconnect and reconnect it to begin charging the battery.  
Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to  
a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.  
If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or  
before any calls can be made.  
Use the battery only for its intended purpose. Never use any charger or battery that is damaged.  
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes  
direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This  
might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage  
the battery or the connecting object.  
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and  
lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery  
may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures  
well below freezing.  
Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according  
to local regulations. Please recycle when possible. Do not dispose as household waste.  
Do not dismantle or shred cells or batteries. In the event of a battery leak, do not allow the liquid to come in contact with the  
skin or eyes. In the event of such a leak, flush your skin or eyes immediately with water, or seek medical help.  
Nokia battery authentication guidelines  
Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an  
authorized Nokia dealer, look for the Nokia Original Enhancements logo on the packaging, and inspect the hologram label using  
the following steps:  
Successful completion of the four steps is not a total assurance of the authenticity of the battery. If you have any reason to  
believe that your battery is not an authentic, original Nokia battery, you should refrain from using it, and take it to the nearest  
authorized Nokia service point or dealer for assistance. Your authorized Nokia service point or dealer will inspect the battery  
for authenticity. If authenticity cannot be verified, return the battery to the place of purchase.  
Authenticate hologram  
1. When looking at the hologram on the label, you should see the Nokia connecting hands symbol from one  
angle and the Nokia Original Enhancements logo when looking from another angle.  
2. When you angle the hologram left, right, down, and up, you should see 1, 2, 3, and 4 dots on each side  
respectively.  
3. Scratch the side of the label to reveal a 20-digit code, for example, 12345678919876543210. Turn the  
battery so that the numbers are facing upwards. The 20-digit code reads starting from the number at the  
top row followed by the bottom row.  
41  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
B a t t e r y  
To create a text message, enter the 20-digit code, for example, 12345678919876543210, and send to +44  
7786 200276.  
National and international operator charges will apply. You should receive a message indicating whether the  
code can be authenticated.  
What if your battery is not authentic?  
If you cannot confirm that your Nokia battery with the hologram on the label is an authentic Nokia battery, please do not use  
the battery. Take it to the nearest authorized Nokia service point or dealer for assistance. The use of a battery that is not approved  
by the manufacturer may be dangerous and may result in poor performance and damage to your device and its enhancements.  
It may also invalidate any approval or warranty applying to the device.  
To find out more about original Nokia batteries, visit www.nokia.com/battery.  
42  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Care and maintenance  
Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will  
help you protect your warranty coverage.  
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode  
electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing  
it.  
Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.  
Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp  
or melt certain plastics.  
Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device  
and damage electronic circuit boards.  
Do not attempt to open the device other than as instructed in this guide.  
Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.  
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.  
Do not paint the device. Paint can clog the moving parts and prevent proper operation.  
Use a soft, clean, dry cloth to clean any lenses, such as camera, proximity sensor, and light sensor lenses.  
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could  
damage the device and may violate regulations governing radio devices.  
Use chargers indoors.  
Always create a backup of data you want to keep, such as contacts and calendar notes.  
To reset the device from time to time for optimum performance, power off the device and remove the battery.  
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly,  
take it to the nearest authorized service facility for service.  
Disposal  
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union all  
electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their  
working life. Do not dispose of these products as unsorted municipal waste.  
Return the products to collection to prevent possible harm to the environment or human health from uncontrolled waste  
disposal and to promote the sustainable reuse of material resources. Collection information is available from the product retailer,  
local waste authorities, national producer responsibility organizations, or your local Nokia representative. For more information,  
Additional safety information  
Small children  
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.  
Operating environment  
This device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at  
least 2.2 centimeters (7/8 inches) away from the body. When a carry case, belt clip, or holder is used for body-worn operation,  
it should not contain metal and should position the device the above-stated distance from your body.  
To transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data  
files or messages may be delayed until such a connection is available. Ensure the above separation distance instructions are  
followed until the transmission is completed.  
Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic  
storage media near the device, because information stored on them may be erased.  
Medical devices  
Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately  
protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately  
shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations  
43  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
A d d i t i o n a l s a f e t y i n f o r m a t i o n  
posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive  
to external RF energy.  
Implanted medical devices  
Manufacturers of medical devices recommend that a minimum separation of 15.3 centimeters (6 inches) should be maintained  
between a wireless device and an implanted medical device, such as a pacemaker or implanted cardioverter defibrillator, to  
avoid potential interference with the medical device. Persons who have such devices should:  
Always keep the wireless device more than 15.3 centimeters (6 inches) from the medical device when the wireless device is  
turned on.  
Not carry the wireless device in a breast pocket.  
Hold the wireless device to the ear opposite the medical device to minimize the potential for interference.  
Turn the wireless device off immediately if there is any reason to suspect that interference is taking place.  
Read and follow the directions from the manufacturer of their implanted medical device.  
If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.  
Hearing aids  
Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.  
Vehicles  
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel  
injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more  
information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added.  
Only qualifiedpersonnelshouldservice the device orinstallthe device inavehicle. Faulty installationorservice may be dangerous  
and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment in your vehicle  
is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same  
compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate  
with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the  
air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could  
result.  
Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless  
teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may  
be illegal.  
Potentially explosive environments  
Switch off your device when in any area with a potentially explosive atmosphere, and obey all signs and instructions. Potentially  
explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas  
could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near  
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas;  
chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not  
always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied  
petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust, or metal  
powders.  
Emergency calls  
Important: Wireless phones, including this device, operate using radio signals, wireless networks, landline networks,  
and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never  
rely solely on any wireless device for essential communications like medical emergencies.  
To make an emergency call:  
1. If the device is not on, switch it on. Check for adequate signal strength.  
Some networks may require that a valid SIM card is properly inserted in the device.  
2. Press the end key as many times as needed to clear the display and ready the device for calls.  
3. Enter the official emergency number for your present location. Emergency numbers vary by location.  
4. Press the call key.  
If certain features are in use, you may first need to turn those features off before you can make an emergency call. Consult this  
guide or your service provider for more information.  
When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the  
only means of communication at the scene of an accident. Do not end the call until given permission to do so.  
44  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
A d d i t i o n a l s a f e t y i n f o r m a t i o n  
CERTIFICATION INFORMATION (SAR)  
This mobile device meets guidelines for exposure to radio waves.  
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves  
recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP  
and include safety margins designed to assure the protection of all persons, regardless of age and health.  
The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The  
SAR limit stated in the ICNIRP guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests for SAR are  
conducted using standard operating positions with the device transmitting at its highest certified power level in all tested  
frequency bands. The actual SAR level of an operating device can be below the maximum value because the device is designed  
to use only the power required to reach the network. That amount changes depending on a number of factors such as how  
close you are to a network base station. The highest SAR value under the ICNIRP guidelines for use of the device at the ear is  
0.82 W/kg (RM-237) and 0.96 W/kg (RM-274).  
Use of device accessories and enhancements may result in different SAR values. SAR values may vary depending on national  
reporting and testing requirements and the network band. Additional SAR information may be provided under product  
45  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Index  
codes  
A
configuration 28  
access codes  
configuration setting service  
connectivity 40  
active standby 11, 24  
alarm clock 35  
contact information  
contacts 21  
business cards 22  
copy 22  
antenna  
anykey answer 27  
applications 34, 35  
audio messaging 16  
automatic redial 27  
delete 22  
dialing shortcuts 23  
edit details 22  
groups 22  
B
background image 24  
info numbers 23  
move 22  
barring password  
battery 41  
my numbers 23  
save details 21  
save names 21  
save phone numbers 21  
search 22  
charging  
battery charge status 11  
blacklist 18  
Bluetooth 25, 40  
bookmarks 38  
browser 37  
service numbers 23  
settings 22  
appearance settings 38  
bookmarks 38  
browse pages 37  
cache 39  
synchronize 22  
cookies 38  
countdown timer 36  
CSD 40  
certificates 39  
cookies 38  
currency conversion 36  
customer service  
digital signature 39  
security 39  
D
WML scripts 38  
data  
C
communication 40  
transfer 26  
cache memory 39  
calculator 36  
calendar 35  
note 36  
data cable 27, 40  
date settings 24  
dialing 12  
dialing shortcuts 13, 23  
digital signature 39  
display 11, 24  
call divert 27  
call functions 12  
call log 23  
call waiting 13, 27  
caller id 27  
calls  
downloads 7, 38  
E
e-mail application 17  
edit text 13  
answer 13  
dialed 23  
ending a call 12  
enhancements 27  
equalizer 32  
international 12  
making of 12  
missed 23  
exchange rate 36  
options 13  
received 23  
reject 13  
F
factory settings 29  
flash messages 16  
flight mode 12  
flight query 27  
See also flight mode  
font size 24  
voice dialing 13  
camera 30  
capitals 13  
case  
lower 13  
upper 13  
certificates 39  
channel types 33  
characters 13  
G
gallery 29  
files 29  
charge the battery  
clock 24  
folders 29  
games 34  
46  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
I n d e x  
H
N
handsfree  
navigation 14  
Nokia contact information  
note 36  
See loudspeaker  
headphones  
headset  
notes 36  
help text 27  
number dialing 12  
HSCSD 40  
number mode 13  
I
O
idle mode 10  
offline mode 12  
operator menu 29  
organizer 35  
indicators 11  
info messages 20  
info numbers 23  
P
installation  
packet data 40  
parts 10  
instant messaging 18  
internet 37  
PC connectivity 40  
PC Suite 40  
interval timer 36  
J
phone software updates 27  
phonebook  
junk folder 18  
See contacts  
K
phonelock  
keyguard 12, 27  
keypad lock 12  
keys 10  
See keypad lock  
PictBridge 27  
picture 30  
keyguard 12  
PIN codes  
keypad lock 12  
positioning 23  
postcards 16  
power saver 24  
power saving 11  
predictive text input 14  
print images 29  
profiles 23  
L
language 27  
voice playback 27  
location information 23  
log 23  
loudspeaker 13  
PTT  
See push to talk  
M
PUK codes  
media player 30  
memory card 29  
push to talk 32  
settings 34  
insert  
pushed messages 38  
memory full 17  
menu 14  
R
message center number 14  
message sending 16  
messages  
Radio 31  
recorder 32  
redial 27  
audio messaging 16  
delete 20  
S
flash messages 16  
folders 17  
screen 24  
screen saver 24  
scrolling 14  
security  
info messages 20  
postcard 16  
service commands 20  
settings 20  
browser 39  
certificates 39  
SIM messages 20  
text 14  
codes  
module 39  
security code  
service  
voice messages 20  
microSD card  
insert  
inbox 38  
MMS  
messages 38  
service commands 20  
service numbers 23  
services 37  
See multimedia messages  
multimedia messages 15  
music player 31  
my numbers 23  
SIM 40  
47  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I n d e x  
settings 23  
themes 24  
time settings 24  
time zone 24  
timer 36  
active standby 24  
Bluetooth 25  
browser appearance 38  
call 27  
to-do list 36  
tones 24  
clock 24  
traditional text input 14  
configuration 28  
data transfer 26  
date 24  
U
unlock keypad 12  
USB data cable 27  
display 24  
downloads 38  
enhancements 27  
font size 24  
V
video clips 30  
messages 20  
phone 27  
visual radio 32  
voice clarity 27  
voice commands 25  
voice dailing 13  
voice messages 20  
voice recorder 32  
power saver 24  
profiles 23  
push to talk 34  
restoring 29  
screen saver 24  
security 28  
W
service inbox 39  
shortcuts 24  
sleep mode 24  
standby mode 24  
themes 24  
wallpaper 24  
web 37  
welcome note 27  
wireless markup language 37  
WML scripts 38  
write text 13  
time 24  
time zone 24  
tones 24  
X
USB data cable 27  
wallpaper 24  
shortcuts 11, 24  
left selection key 24  
right selection key 24  
scroll key 25  
voice commands 25  
signal strength 11  
SIM  
XHTML 37  
messages 20  
services 40  
SIM card 12  
installation  
sleep mode 24  
SMS  
See text message  
software update 7, 28, 29  
requesting 28  
spam filter 18  
speed dialling 27  
standby mode 10, 24  
start up tone 27  
status indicators 11  
stereo widening 32  
stopwatch 37  
strap  
streaming service 30  
synchronization 26  
T
take a picture 30  
text 13  
text message 14  
text modes 13  
48  
© 2007 Nokia. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop KM 490 KM 491 KM 493 KM 494 KM 497 KM 498 KM 490 1 KM 491 1 KM 493 1 KM 494 1 KM 497 1 KM 498 1 User Manual
Miele Dishwasher 9645480 User Manual
Nextar GPS Receiver Q4 User Manual
Nikon Power Supply UPS User Manual
Nuvo Home Theater System NV E6GM User Manual
Onkyo Stereo Receiver TX SR600 600E User Manual
Optimus Car Stereo System 12 2154 User Manual
Oregon Scientific Thermometer EMS100 User Manual
P3 International Thermostat E9310 User Manual
ParaBody Home Gym 835102 User Manual