Nokia Holder Easy Mount
HH-12
4
1
2
3
Issue 2
ownload from Www.Somanuals.com. All Manuals Search And Downloa
© 2006 Nokia. All rights reserved.
Nokia and Nokia Connecting People are
registered trademarks of Nokia
Corporation.
Introduction
This mounting device allows you to attach the mounting device to the
attach your compatible Nokia windshield, adjust the mounting
mobile holder to the windshield of device into the desired position,
your vehicle.
and attach your mobile holder to
the mounting device.
To use the mounting device with
your compatible mobile holder,
General safety instructions
Obey all local laws. Always keep
your hands free to operate the
vehicle while driving. Your first
When you install the mounting
device or mobile holder, ensure
that they do not interfere with or
consideration while driving should hinder the steering or braking
be road safety. Only operate the systems or other systems used in
mounting device or mobile holder the operation of the vehicle (for
if it is safe to do so under all
driving conditions.
example, airbags) or disturb your
field of vision while driving.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Check that the deployment of the windshield, especially if the
airbag is not blocked or impaired in ambient temperature changes a
any way.
Ensure that the mounting device or Never leave the mounting device
mobile holder is not installed inside the vehicle in direct sunlight
lot.
where you might come in contact or in excessive heat. The mounting
with it in the event of an accident device and suction cup may be
or collision.
damaged and adhesion may be
impaired if the inside temperature
exceeds +70°C (160°F).
Periodically check that the suction
cup at the bottom of the mounting
device is firmly attached to the
Attach to a windshield
Locate a safe mounting surface on not heat the windshield excessively
the windshield, and clean the
to avoid damage to it.
surface thoroughly with a glass
cleaner and a clean towel. If the
ambient temperature is below
+15°C (60°F), carefully warm the
surface and the suction cup with a
hair dryer to ensure a firm grip on
the windshield. Ensure that you do
Press the suction cup at the
bottom of the mounting device
firmly on the windshield (see step
1 at the start of this guide), and
carefully push the locking lever
inside the mounting device (2)
towards the suction cup to create
ownload from Www.Somanuals.com. All Manuals Search And Downloa
a vacuum between the suction cup the locking lever toward the top of
and the windshield. Check that the the mounting device (3), and pull
suction cup is firmly attached.
the strap located on the edge of
the suction cup (4).
To detach the mounting device
from the windshield, carefully push
Set to the desired position
Do not adjust the mounting device (5). Ensure that the top of the
while driving.
device is firmly locked into place.
To set the top of the mounting
device to the desired position,
loosen the two screws in the
middle of the mounting device,
turn the top to the desired
To set the mounting plate at the
top of the mounting device to the
desired position, loosen the screw
below the plate, turn the plate to
the desired position, and tighten
the screw (6).
position, and tighten the screws
Mount the mobile holder
To attach a compatible Nokia
mobile holder to the mounting
For example, to use the mobile
holder CR-39, remove the
plate, use the screw supplied with protection plate with the Nokia
the holder. text from the holder, attach the
ownload from Www.Somanuals.com. All Manuals Search And Downloa
holder to the mounting plate with dimensions: height 95 - 120 mm,
the supplied screw, and replace the width 42 - 55 mm, thickness 13 -
protection plate (7). Insert your
phone into the holder, and press
the clamps at the sides of the
holder until the phone is firmly in
place. To release the phone, press
the button below the left clamp.
The mobile holder CR-39 supports
mobile devices with the following
26 mm, weight 200 g at maximum.
When attaching a mobile holder,
ensure that the phone display is
clearly visible for the user. For your
safety, install the holder in the
upright position.
Care and maintenance
Your device is a product of superior
design and craftsmanship and
should be treated with care. The
suggestions below will help you
protect your warranty coverage.
•
•
•
Do not use or store the device in
dusty, dirty areas. Its moving
parts can be damaged.
Do not drop, knock, or shake the
device. Rough handling can
break fine mechanics.
•
Keep all accessories and
enhancements out of the reach
of small children.
Do not use harsh chemicals,
cleaning solvents, or strong
detergents to clean the device.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
•
Do not paint the device. Paint
can clog the moving parts and properly, take it to the nearest
If the product is not working
prevent proper operation.
authorized service facility for
service.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
|