SHIFT_obsession
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT BRIGHTNESS CONTROL
STEERING WHEEL SWITCHES FOR AU-
TRACTION CONTROL SYSTEM (TCS)
OFF SWITCH
FUEL FILLER DOOR RELEASE
STEERING WHEEL TILT ADJUSTMENT*
HOOD RELEASE*
CONTROL PANEL DISPLAY
AUDIO SYSTEM
DIO CONTROL/BLUETOOTHா
TRIP COMPUTER/MODE SETTING BUT-
TONS
HEADLIGHT AND TURN SIGNAL CON-
TROL
CRUISE CONTROL
CLIMATE CONTROLS
SOFT TOP OPERATING SWITCH (ROAD-
STER MODELS ONLY)
WINDSHIELD WIPER/WASHER SWITCH
*See your Owner’s Manual for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE KEYLESS ENTRY SYSTEM
LOCK DOORS
Press the
button to lock all doors.
UNLOCK DOORS
Press the
button once to unlock the driver’s door
only. Press the button again within 5 seconds to unlock
all doors.
RELEASING TRUNK LID
Press and hold the trunk release button for longer than 0.5 seconds to open the trunk
lid.
USING THE PANIC ALARM
Press and hold the
button for longer than 0.5 seconds. The panic alarm will
sound and the headlights will stay on for 30 seconds. The panic alarm stops when it
has run for 30 seconds or when any button is pressed on the keyfob.
OPENING THE WINDOWS
Windows can be lowered using the keyfob while approaching the vehicle.
Ⅲ
Ⅲ
Ⅲ
Press and hold the
To stop lowering windows at any time, release the
Continue to press and hold the button until windows are fully open.
button. The driver’s and passenger’s windows will be lowered.
.
SILENCING THE HORN BEEP FEATURE
Ⅲ
To deactivate: Press and hold the
To activate: Press and hold the
and
and
buttons for at least 2 seconds.
buttons for at least 2 seconds.
Ⅲ
WINDSHIELD WIPER/WASHER SWITCH
Ⅲ
The ignition switch must be in the ON position to
activate the windshield wipers.
Ⅲ
Move the lever to the following positions to operate
the windshield wipers:
Intermittent (INT) – Front wipers operate in-
termittently and can be further adjusted by
twisting the time control ring
.
Low Speed (LO) – Continuous low-speed
operation of front wipers.
High Speed (HI) – Continuous high-speed
operation of front wipers.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
Rear Wipers (REAR) – Twist the end section to operate the first (INT) or second
(ON) speed settings for the rear wipers.
Ⅲ
The washer function activates the washer fluid and several sweeps of the wipers:
● For FRONT WASHER, pull lever toward you.
● For REAR WIPER, push lever away from you.
HEADLIGHT AND TURN SIGNAL CONTROL
HEADLIGHT CONTROL SWITCH
Ⅲ
Turn the headlight control switch
to the
position to turn on the front parking, tail, license plate
and instrument panel lights.
Ⅲ
Turn the headlight control switch
to the
po-
sition to turn on the headlights. All other lights remain
on.
FOG LIGHT OPERATION
NOTE: The headlights must be on and the low beams selected for the fog lights to operate.
Ⅲ
Ⅲ
Turn the switch (inside collar)
Turn the switch (inside collar)
to the
position to turn on the fog lights.
to the OFF position to turn off the fog lights.
TURN SIGNAL SWITCH
Ⅲ
Move the headlight control switch up or down
to
signal a turning direction. When the turn is completed,
the turn signals cancel automatically.
Ⅲ
To signal a lane change, move the headlight control
switch up or down
to the point where the indica-
tor light begins to flash, but the headlight control switch
does not latch.
HIGH BEAM
Ⅲ
Push the headlight control switch forward
select the high beam function. The blue
to
indicator
light illuminates. Pull the headlight switch back to the
original position to select the low beam. The blue
indicator light goes off.
Ⅲ
Pull and release the headlight control switch
and off.
to flash the headlight high beams on
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RPM SHIFT INDICATOR (manual transmission only)
The engine RPM shift indicator light (REV) is located in
the tachometer
. When driving, it indicates ‘shift
point’, or time to up-shift.
Ⅲ
Ⅲ
Ⅲ
Set or deactivate the engine RPM shift point using
the trip computer display.
REV indicator will flash when the engine speed is
within 500 RPM of the set shift point.
01
REV light will illuminate when the engine speed
matches the set shift point RPM.
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTHா (if so equipped)
Ⅲ
Press the MODE button to turn the radio system on.
Ⅲ
Press MODE repeatedly to change to the following
mode:
● Without XMா radio: AM, FM1, FM2, and CD or CD
changer.
● With XMா radio: AM, FM1, FM2, SAT1, SAT2 and
CD changer.
Ⅲ
The SEEK up or down
switch can be used to
perform the following:
● Push the SEEK
switch for less than 1.5 seconds to change the radio frequency.
● Push and hold the SEEK
switch for more than 1.5 seconds to seek the next or
previous broadcasting radio station.
● Push the SEEK
switch while playing a CD for less than 1.5 seconds to change
tracks on the CD.
● If the vehicle is equipped with a CD changer, push and hold the SEEK
switch for
more than 1.5 seconds to change between CDs.
● Push and hold the SEEK
switch for more than 1.5 seconds while playing an MP3
CD to change folders (if multiple folders exist).
Ⅲ
Push the VOL control switch
up or down to increase or decrease the volume.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CRUISE CONTROL (if so equipped)
Ⅲ
To activate the cruise control, push the ON·OFF
switch. The indicator light in the instrument panel will
illuminate.
Ⅲ
To set cruising speed, accelerate the vehicle to the
desired speed, push the COAST/SET switch and
release it. The SET indicator light in the instrument
panel will illuminate.
Ⅲ
Ⅲ
To reset at a faster cruising speed, push and hold the
ACCEL/RES switch. When the vehicle attains the
speed you desire, release the switch.
To reset at a slower cruising speed, push and hold
the COAST/SET switch. Release the switch when
the vehicle slows to the desired speed.
Ⅲ
Ⅲ
Ⅲ
To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET
indicator light in the instrument panel will go out.
To resume a preset speed, push and release the ACCEL/RES switch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
To turn off cruise control, push the ON·OFF switch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
SCREW-IN RECOVERY HOOK
Ⅲ
Your vehicle is supplied with a screw-in recovery hook
for pulling the vehicle forward. For example: Pulling the
vehicle onto a flat bed for towing.
Ⅲ
The screw-in recovery hook tool is located in the right
rear luggage compartment area under the cover along
with the vehicle jack.
To install the recovery hook:
Ⅲ
Ⅲ
Remove the recovery hook cover from the front grill.
Install the recovery hook as shown in the photo. Turn it
clockwise until securely tightened.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO CLIMATE CONTROL
AUTO MODE
Turn both the fan speed control dial
and the air flow control dial
to the AUTO
positions
. Then turn the temperature control dial to the desired temperature.
This will allow the fan speed, air flow distribution and temperature to be automatically
maintained.
TEMPERATURE CONTROL DIAL
Turn the temperature control dial left for cold air or right for hot air.
AIR FLOW CONTROL DIAL
Turn the dial to select the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vent.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
The air flow distribution of the passenger compartment will be maintained
automatically when the control dial is turned to the AUTO position.
FAN SPEED CONTROL DIAL
Turn the fan speed control dial to the left (slower) or right (faster) to manually control fan
speed. Turn the dial to the AUTO position to automatically control fan speed.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Ⅲ Turn the air flow control dial to the front window defroster mode
. The A/C
automatically turns on when the defroster mode is selected.
Ⅲ Turn the temperature control dial left or right to set the desired temperature.
Ⅲ To set the defroster on high, turn the fan speed dial all the way to the right.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFROSTING/DEFOGGING REAR WINDOW AND OUTSIDE HEATED
MIRROR
Push the rear window defroster switch
on. Push the switch again to manually turn
the defroster off. This function automatically turns off in approximately 15 minutes.
A/C ON/OFF BUTTON
Press the A/C button to manually turn the A/C on or off.
AIR RECIRCULATION/FRESH AIR BUTTON
Ⅲ Press the air intake button to alternate between
(air recirculation) and
(fresh air).
Ⅲ The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position
.
NOTE: When the center button is pressed to recirculate the interior air, the A/C will
automatically turn on (if not already on). This is done to help reduce window fogging.
REAR FLOOR BOX
Ⅲ
Rear floor storage is located behind the passenger’s
seat.
Ⅲ
Fold the passenger’s seatback forward to access the
rear floor box.
Ⅲ
Ⅲ
Coupe – Pull up on the lever
.
Roadster – Push the upper portion of the passenger
power seat switch
Pull up on the lever
.
Ⅲ
to open the rear floor box.
NOTE: The rear floor storage box has additional space un-
der the bottom plate.
Ⅲ
Using the master key, lock the storage box (turn key to
the right) or unlock the storage box (turn key to the left).
Ⅲ
Return the passenger’s seatback to a locked position
after using the rear floor box.
Ⅲ
Ⅲ
Coupe – Pull up on the lever
original position.
to return seatback to
Roadster – Push lower portion of the passenger power
seat switch to return seatback to original position.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM/XMா* RADIO WITH CD CHANGER (if so equipped)
LOAD BUTTON
Ⅲ LOAD A SINGLE DISC - Press the
button for less than 1.5 seconds. Select the
loading slot by pressing one of the CD insert select button (1 - 6 ), then insert the CD.
Ⅲ LOAD UP TO 6 DISCS - Press and hold the
button for more than 1.5 seconds.
The slot numbers (1-6) will illuminate on the display when CDs are loaded into the
changer.
SCAN BUTTON
Press the SCAN button to stop at each broadcasting station (FM, AM or XMா) for 5
seconds. Pressing the button again during this 5-second period will stop scan tuning
and the radio will remain tuned to that station. If the SCAN button is not pressed within
5 seconds, scan tuning moves to the next station.
RADIO BUTTON
Press the RADIO band select button to change the band as follows:
Ⅲ Without satellite radio: AM → FM1 → FM2 → AM
Ⅲ With satellite radio: AM → FM1 → FM2 → SAT1 → SAT2 → AM
EJECT BUTTON
Ⅲ EJECT A SINGLE DISC - Press the
button for less than 1.5 seconds. Select the
eject slot by pressing the CD insert select button (1 - 6 ). The CD will then eject.
Ⅲ EJECT ALL DISCS - Press and hold the
button for more than 1.5 seconds. The
CDs will be ejected one after another.
TUNE/REW/FF BUTTON
Ⅲ To manually tune the radio, press the TUNE/REW/FF button.
Ⅲ When the TUNE/REW/FF button is pressed while a CD is playing, it will fast forward
or rewind. When the button is released, the CD will play at normal speed.
RPT BUTTON
To change the play pattern of the CD, press the RPT button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO BUTTON
To adjust the Bass, Treble, Fade, Balance, and Audio Pilot, press the AUDIO button until
the desired mode appears in the display. Then press the TUNE/REW/FF button to
adjust to the desired level.
STATION AND CD SELECT BUTTONS
Ⅲ To store a station in a preset you must first select AM, FM1, FM2, SAT1 or SAT2 radio
band by pressing the RADIO button and tune to the desired FM, AM or XMா station.
Then press and hold the desired station select button for at least 2 seconds. When
the preset indicator illuminates, a beep will sound, indicating memorization is com-
plete. To retrieve a previously set station, select the radio band where the preset was
set, then press the corresponding station select button.
Ⅲ While playing a CD, to select a different CD loaded into the CD changer press one of
the CD select buttons (1 - 6 ).
DISP BUTTON
Pressing the DISP button will display additional information (for example: Title, Artist
name).
Ⅲ MP3 PLAYBACK (if so equipped)
In addition to playing audio CDs, the audio system can play MP3 files recorded on
CD-ROM, CD-R, and CD-RW discs. Each disc can have a maximum of 8 folder levels
and 255 folders. A total of 512 MP3 files can be played back. During MP3 playback,
some recorded ID3 tag information can be displayed by pressing the DISP button.
Use the TUNE/REW/FF button to navigate the MP3 folders.
SEEK/TRACK BUTTON
Ⅲ To scan quickly through each broadcasting station, press the SEEK/TRACK button.
Ⅲ To skip from one track to another on a CD, press the SEEK/TRACK button. Each
time the button is pressed, the CD will advance or skip back one track.
*XMா Satellite Radio is only available on vehicles equipped with optional XMா satellite
subscription service.
CLOCK SET/ADJUSTMENT
NAVIGATION SYSTEM ONLY (if so equipped)
Press the SETTING button, then select the “Clock”
key using the joystick and press the ENTER button
to access the following clock settings:
Ⅲ
On-screen Clock – When this item is turned to
ON, a clock is always displayed in the upper
right corner of the screen. The clock is automati-
cally adjusted by the GPS system.
Ⅲ
Clock Format – Choose either the 12-hour
clock display or the 24-hour clock display.
Ⅲ
Ⅲ
Ⅲ
Offset Adjust – Adjust the time by increasing or decreasing per minute.
Daylight Saving Time – Turn this item to ON for daylight savings time application.
Time Zone – Choose the time zone.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM/XMா RADIO WITH CD CHANGER (if so equipped)
Ⅲ
Press and hold the RPT button for approximately 2 seconds until the clock display starts
to flash.
Ⅲ
Ⅲ
Ⅲ
Press the SEEK/TRACK button to adjust the hours.
Press the TUNE/REW/FF button to adjust the minutes.
Press the RPT button again to exit the clock set mode.
TRIP COMPUTER
The trip computer may be used to check items such as speed,
outside air temperature, distance to empty (fuel), average mile-
age and speed, elapsed time and distance traveled. Additionally,
it can function as a stopwatch or be used to operate the RPM
shift feature (REV) (Manual transmission only).
Ⅲ
Ⅲ
Ⅲ
The twin trip odometer records the distance of individual
trips.
Press the button
to change the display as follows: Trip
A → Trip B → Trip A.
Press and hold the button for more than 1 second to reset
the trip odometer to zero.
TO OPERATE THE TRIP COMPUTER
Turn the ignition switch ON. Then press the side of the buttons.
Ⅲ
Ⅲ
Press the button
mode.
toward the left to scroll through each
Press the button
toward the left to reset or adjust the various mode selections.
AUTOMATIC TRANSMISSION (if so equipped)
MANUAL SHIFT MODE
Ⅲ
When the shift selector lever is shifted from D (Drive)
to the manual shift gate, the transmission enters the
manual shift mode.
Ⅲ
In the manual shift mode, shift range is displayed on
the position indicator in the meter.
WHEN SHIFTING UP
Move the shift selector lever to the + (up) side. (Shifts to higher range.)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEN SHIFTING DOWN
Move the shift selector lever to the – (down) side. (Shifts to lower range.)
Ⅲ
In manual shift mode, the transmission automatically shifts down to M1 (first) before the
vehicle comes to a stop. When accelerating again, it is necessary to shift to the desired
range.
Ⅲ
Ⅲ
Moving the shift selector lever rapidly to the same side twice will shift the ranges in
succession.
When canceling the manual shift mode, return the shift selector lever to the D (Drive)
position. The transmission returns to the normal driving mode.
6-SPEED MANUAL TRANSMISSION (if so equipped)
REVERSE GEAR
LOCK OUT
Ⅲ
In 6-speed manual transmission equipped vehicles, the shift lever is equipped with a
Reverse lock-out feature that prevents accidental selection of Reverse (instead of 1st
gear).
SHIFTING TO REVERSE
Ⅲ
Depress the shift lever down, then move it to the right and back into Reverse.
NOTE: When shifting, always depress the clutch pedal fully to avoid noise and gear grind.
CONTROL PANEL DISPLAY WITH NAVIGATION SYSTEM (if so
equipped)
INFO BUTTON
When the INFO button is pressed, the
Maintenance screen will be displayed.
MAINTENANCE ITEMS
You can set the engine oil and the oil filter
maintenance interval. To display the set-
ting of the maintenance interval, select the
ENGINE OIL or OIL FILTER key using the
joystick and press the ENTER button. To
set the maintenance interval, select the
INTERVAL key using the joystick and
push the joystick to the right or left. To
reset the maintenance interval, select the RESET DISTANCE key using the joystick and
press the ENTER button.
DISPLAY SCREEN SETTINGS
The SETTINGS screen will appear when the SETTING button is pressed. Select the
DISPLAY key with the joystick and press the ENTER button to choose from various display
screen options. The DISPLAY key will allow you to personalize the information shown on the
display screen, such as climate control or audio system display.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTION CONTROL SYSTEM (TCS) OFF SWITCH (if so equipped)
The vehicle should be driven with the Traction Control System (TCS) on
for most driving conditions. TCS reduces the engine output to reduce
wheel spin. The engine speed will be reduced even if the accelerator is
depressed to the floor. If maximum engine power is needed to free a
stuck vehicle, such as from mud or snow, turn the TCS off.
Ⅲ
To turn off the TCS, push the TCS OFF switch. The indicator light
will illuminate.
Ⅲ
Push the switch again or restart the engine and the system will
operate normally.
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag
System. Under some conditions, depending on the type of
occupant or object detected in the front passenger seat by
the occupant classification sensor, the front-passenger air
bag is designed to automatically turn OFF. When the front-
passenger air bag is OFF, the front-passenger air bag status
light will illuminate*. For example:
Ⅲ
When the system detects that the front-passenger’s
seat is occupied by a small adult, child or child restraint
as outlined in the Owner’s Manual, the
will illuminate to indicate that the front-
passenger air bag is OFF and will not inflate in a crash.
Ⅲ
When the front-passenger’s seat is occupied and the passenger meets the conditions
outlined in the Owner’s Manual, the
will not illuminate to indicate that the
front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the
passenger air bag status light will not illuminate even though the front-passenger
air bag is OFF.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. If the low tire pressure warning
light illuminates, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pressure
shown on the Tire and Loading Information label located in the driver’s
door opening. After tire pressures are adjusted, the vehicle will need
to be driven at speeds above 16 MPH (25 km/h) to activate the TPMS
and turn off the low tire pressure warning light.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT BELT WARNING LIGHT AND CHIME
Ⅲ
The light and chime remind you to fasten your seat belts. The light
illuminates whenever the ignition key is turned to the ON or
START position and remains illuminated until the driver’s seat
belt is fastened. At the same time, the chime sounds for approxi-
mately 6 seconds unless the driver’s seat belt is securely fas-
tened.
Ⅲ
The seat belt warning light may also illuminate if the front pas-
senger’s seat belt is not fastened when the front passenger’s
seat is occupied. For 7 seconds after the ignition switch is in the ON position, the system
does not activate the warning light for the front passenger.
FRONT SEAT ADJUSTMENTS
With manual seats:
Ⅲ
Ⅲ
Ⅲ
Pull up on the lever under the front of the
seat and slide backward or forward to the
desired position. Release the lever to lock
the seat in position.
Lift the lever on the side of the seat to adjust
your seatback forward or backward; release
when you have found a comfortable angle
and the seat belt fits properly.
Turn either dial to adjust the angle and height of the seat cushion to the desired position.
With power seats (if so equipped):
Ⅲ
Move the sliding switch
forward or
backward to adjust the seat cushion to the
desired position.
Ⅲ
Ⅲ
Move the reclining switch
forward or
backward to adjust the seatback to the de-
sired angle.
Turn either dial to adjust the angle and height of the seat cushion to the desired position.
SEATBACK TILT CANCEL SWITCH (Roadster only)
The passenger seat of the 350Z Roadster automatically tilts forward
when operating the soft top. This function can be cancelled by
pushing the seatback tilt cancel switch to the CANCEL position.
Push the seatback tilt cancel switch to the AUTO position to reacti-
vate the power seatback tilt switch.
If the seatback tilt cancel switch is in the CANCEL position, the
seatback tilt paddle switch (located on the back of the passenger
seat) will not work. In this situation, tilt the passenger seatback
forward using the power seat position switch.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER WINDOWS
The power windows operate when the ignition key is in the ON
position, and for about 45 seconds after the ignition key is
turned to the OFF position.
AUTOMATIC ADJUSTING FUNCTION:
The front door power windows have an automatic adjusting
function. This ensures the windows close completely to help
seal against wind noise and weather leaks.
When the front doors are being opened, the windows auto-
matically lower slightly to avoid contact between the windows and the side roof panels.
When the doors are closed, the windows automatically raise slightly.
SECONDARY REAR HATCH RELEASE
Your vehicle is equipped with a secondary rear hatch
release mechanism. This allows opening of the rear
hatch in the event of a discharged battery or in an
emergency.
Ⅲ
The secondary rear hatch release is located under
the strut tower bar (Coupe), or inside the storage
bin compartment (Roadster - upper right side).
Ⅲ
To open the rear hatch from the inside, firmly pull
the release handle to the left towards the passen-
ger side until the lock releases.
MIRROR ADJUSTMENT
The rear view mirror has two pivot points for adjustments. Adjust
the rear view mirror height at the rear pivot and tilt the mirror at the
front pivot. Position the mirror to provide the best visibility through
the rear window.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFT TOP OPERATION
Before opening or closing your soft top, refer
to the Owner’s Manual for detailed Warnings
and Cautions regarding soft top operation.
Open the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmis-
sion) or the N (Neutral) position (manual transmission).
3. Step on the brake pedal.
4. Start the engine.
5. Push the safety switch (black) located in the center of the top latch lever. Push the top
latch lever (silver) forward to unlatch the top.
6. Press and hold the OPEN side of the
soft top operating switch until the
top is fully open and stowed and the
indicator light turns off.
Close the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmission) or the
N (Neutral) position (manual transmission).
3. Step on the brake pedal.
4. Start the engine.
5. Press and hold the CLOSE side of the soft top
operating switch until the top is fully closed and
the indicator light begins to flash.
6. Securely latch the top with the top latch lever.
The indicator light turns off.
If the top does not close when using the operating
switch, refer to the Owner’s Manual for the procedure
to manually close the top.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOMELINKா UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
Ⅲ
Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Your vehicle’s engine should be turned off while programming the
HomeLinkா Transceiver.
Ⅲ
To program your HomeLinkா Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage door openers (manufactured after 1996) have “rolling code protec-
tion”. To program a garage door opener equipped with “rolling code protection”,
you will need to use a ladder to get up to the garage door opener motor to be able
to access the “smart or learn” program button.
PROGRAMMING YOUR HOMELINKா UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, press and hold the two
outer HomeLinkா buttons (to
clear the memory) until the indi-
cator light blinks slowly (after 20
seconds). Release both buttons.
2. Position the end of the hand-
held transmitter 1-3 inches
(26-76 mm) away from the
HomeLinkா surface
3. Using both hands, simultaneously press and hold both the HomeLinkா button you
want to program and the hand-held transmitter button. DO NOT release the
buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLinkா flashes, changing
from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds.
When the indicator light flashes rapidly, both buttons may be released. The rapidly
flashing light indicates successful programming. To activate the garage door or other
programmed device, press and hold the programmed HomeLinkா button - releasing
when the device begins to activate.
5. If the indicator light on the HomeLinkா blinks rapidly for two seconds and then turns
solid, HomeLinkா has picked up a “rolling code” garage door opener signal. You will
need to proceed with the next steps to train the HomeLinkா to complete the
programming which may require a ladder and another person for convenience.
6. Press and release the “smart” or “learn” program button located on the garage door
opener’s motor to activate the “training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire originates from under a light
lens, you will need to remove the lens to access the program button.
NOTE: Once you have pressed and released the program button on the garage
door opener’s motor and the “training light”is lit, you have 30 seconds in which to
perform step 7. Use the help of a second person for convenience to assist when
performing this step.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Quickly within 30 seconds of pressing and releasing the garage door opener
program button, firmly press and release the HomeLinkா button you’ve just pro-
grammed. Press and release the HomeLinkா button up to three times to complete the
training.
8. Your HomeLinkா button should now be programmed. (To program the remaining
HomeLinkா buttons for additional door or gate openers, follow steps 2-8 only).
BLUETOOTHா HANDS-FREE PHONE SYSTEM (if so equipped)
With an overhead microphone and sound
transmitted through the audio system
speaker, the Bluetoothா Hands-Free Phone
System utilizes Bluetoothா wireless technol-
ogy and voice recognition to provide hands-
free cellular phone communication.
SYSTEM OPERATING TIPS
Ⅲ
Close all windows. Surrounding noises
may interfere with system operation and
performance.
Ⅲ
Press the
button on the steering wheel to activate voice recognition.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Wait for the tone before speaking.
Begin speaking a command within 5 seconds of the tone.
To go back to the previous command, say “Go back” or “Correction.”
To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit,” or
press the
button.
Ⅲ
To increase or decrease the volume of the voice prompts, push the VOL (volume) control
switch up or down on the steering wheel or turn the VOL knob on the audio system while
the system is responding.
Ⅲ
Ⅲ
Speak in a clear and natural voice without pausing between words.
If the Voice Recognition system does not recognize your voice commands, train the
system using the Speaker Adaptation Mode.
Ⅲ
Ⅲ
Ⅲ
Some commands are not available while the vehicle is in motion.
The “Help” command can be used in any menu to hear a list of available commands.
For recommended phones and detailed instructions, please visit
PAIRING YOUR PHONE
To use the hands-free feature, you need to set-up, or pair, the system to recognize your
compatible cellular phone(s). 5 Bluetoothா-enabled phones can be paired. After set-up, the
system automatically connects with a paired phone when the ignition is in the ACC or ON
position, as long as the phone is on and in the vehicle.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PAIRING PROCEDURE
NOTE: The vehicle must be stationary when pairing the phone.
1. Press the
button on the steering wheel and wait for the tone.
2. Say “Setup.”
3. Wait for the tone, then say “Pair phone.”
4. Wait for the tone, then say “New phone.”
5. Initiate pairing from the phone.
Ⅲ The pairing procedure varies according to each cellular phone model. For detailed
pairing instructions and a list of compatible phones, please visit
Ⅲ When prompted for a PASSKEY code, enter “1234” from the handset. (The PASS-
KEY code is assigned by NISSAN and cannot be changed.)
6. Say a name for the phone when the system asks you to provide one. You can give the
phone a name of your choice.
7. Say a number between 1 and 5 when the system asks you for a priority level. The
priority level determines which phone interacts with the system when two or more
paired phones are active in the vehicle at the same time. Choose 1 if this is the only
phone or the primary phone.
8. Say “Yes”or “No”when the system asks if you would like to select a custom ring tone.
Follow the instructions provided by the system to choose a ring tone.
SETTING UP YOUR PHONEBOOK – ADDING NEW ENTRIES
Each paired phone has its own dedicated phone book. Each phone book can store up to 40
names. Each name can have up to 4 locations/numbers: Home, Office, Mobile, and Other.
NOTE: The vehicle must be stationary when adding new entries.
1. Press the
button and wait for the tone.
2. Say “Phone book.”
3. Wait for the tone, then say “New entry.”
4. When prompted, say the name for the new entry. For example, say “Michelle.” If the
name is too short or too long, or if it sounds too much like a name that is already
stored in the phone book, the system tells you and prompts you to say a name again.
Choose a new name.
5. Say “Yes” or “No” when the system asks you to confirm the name is correct.
6. Say a location (“Home,” “Office,” “Mobile” or “Other”) when the system asks you to
provide one. The system acknowledges the location.
Ⅲ By Voice command - When prompted, say a phone number for the location. For
example, say “five five five one two one two.” The system repeats the number and
prompts you for the next command.
Ⅲ By Bluetoothா transfer - Say “Transfer entry.” The system acknowledges the com-
mand and asks you to initiate the transfer from the phone handset. The new contact
phone number will be transferred from the cellular phone via the Bluetoothா commu-
nication link. The transfer procedure varies according to each cellular phone. See the
cellular phone owner’s manual for details.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Say “Store” when you are finished entering numbers. The system confirms the name,
location, and number.
8. Say “Yes”or “No”when the system asks if you would like to store another location for
the same name. If you do not respond to the system prompt, the system ends the New
Entry session.
MAKING A PHONE CALL
1. Press the
button.
2. After the tone, do one of the following:
Ⅲ Say “Call [name] [location].” For example, say “Call Michelle Home.”
Ⅲ Say “Call [number].” For example, say “Call 123-456-7891.”
Ⅲ Say “Redial” to redial the previous phone number called by the system.
RECEIVING/ENDING A PHONE CALL
When you receive a phone call, a ring tone sounds through the audio system.
Ⅲ
Ⅲ
To accept the call, press the
To hang up the phone at the end of a call or to disconnect during call placement, press
the button.
button. To reject the call, press the
button.
HOW TO SAY NUMBER
NISSAN voice recognition permits numbers to be spoken in a variety of ways.
Ⅲ
Ⅲ
Say “zero” or “oh” for “0.” Example: 1-800-662-6200 – Say “one eight zero zero six six
two six two oh oh.”
Say “pound”for “#”. Say “star”for “*”. Example: 1-555-1212*123 – Say “one five five five
one two one two star one two three.”
NAVIGATION SYSTEM (if so equipped)
GETTING STARTED
The Navigation System begins
when the ignition switch is in the
ACC or ON position. To help
ensure safe driving, some func-
tions are grayed out, or muted,
while driving. Park the vehicle in
a safe location and then operate
the Navigation System.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
START-UP SCREEN
Ⅲ
Read the precautions carefully, highlight the
“OK” key using the joystick and press the
ENTER button.
NAVIGATION DISPLAY SCREEN
Ⅲ
Displays navigation features and map.
DISABLED WHILE DRIVING
Ⅲ
Not all features can be manually operated
while the vehicle is in motion. The text for these
restricted features turns from white to gray and
cannot be selected.
DAY/NIGHT BUTTON
Ⅲ
Press the
button
to switch be-
tween the day screen (bright) and the night
screen (dark). Within 10 seconds of pressing
the
button
, you can adjust the
brightness of the map display screen by mov-
ing the joystick right or left.
MOVING AROUND WITHIN A MAP
Ⅲ
To maneuver around the navigation display
screen, tilt the joystick corresponding to the
direction that you want to move across the
map. Keep tilting the joystick to continuously
move across the map in that direction. Once
you start moving on the map, the cross pointer
appears.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING BUTTON
Ⅲ
Press the SETTING button
to change or
set navigation preferences.
DEST (DESTINATION) BUTTON
Ⅲ
Press the DEST button
to display the
address book and alternative ways of pro-
gramming a destination.
MAP BUTTON
Ⅲ
Press the MAP button
current location map screen.
to display the
ROUTE BUTTON
Ⅲ
Press the ROUTE button
to display vari-
ous ways to modify the route to a destination.
ZOOM OUT/IN BUTTONS
Ⅲ
Press the
button
or the
button
to increase or decrease the scale
of the map display.
BACK BUTTON
Ⅲ
Press the BACK button
to return to the previous function shown on the navigation
display.
VOICE BUTTON
Ⅲ
Press the VOICE button
to hear the current navigation situation.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CANCEL BUTTON
Ⅲ
Press the CANCEL button
to return to the map screen or cancel the route that has
already been set.
SWITCHING THE MAP VIEW
Ⅲ
Press the MAP button
. The current loca-
tion map screen is displayed.
Ⅲ
Press the ENTER button.
Ⅲ
Highlight the “Map View” key and press the
ENTER button.
Ⅲ
Highlight either one of the “Plan View” keys or
one of the “Birdview” keys and press the EN-
TER button to select the map view. Press the
MAP button
or the “Back” key to accept
the changes.
PLAN VIEW
Ⅲ
Displays the map in a 2-dimensional environ-
ment similar to a road map.
BIRDVIEW™
Ⅲ
Displays the map in an elevated perspective.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING A MENU SCREEN
1. To select a preferred menu key, use the joystick to highlight the corresponding key on
the screen and press the ENTER button.
2. Depending on the key you selected, a detailed menu screen, a character input screen
or a setting screen, etc. is displayed. On the screen displayed, make adjustments,
input information, etc. accordingly.
3. Press the BACK button
to return to the previous screen without applying any
changes; in some cases pressing the BACK button
will accept the changes
you made.
4. Press the MAP button
to return to the current location map screen without
applying any changes.
NOTE: Depending on the menu selected, pressing the MAP button
may not return you
to the current location map screen.
STORING YOUR HOME IN YOUR ADDRESS BOOK
Ⅲ
Ⅲ
Press the DEST button
.
Highlight the “Address Book” key and press
the ENTER button.
Ⅲ
Ⅲ
Ⅲ
Highlight the “Home (Add New)” key and
press the ENTER button, a confirmation mes-
sage is displayed. Highlight the “YES” key and
press the ENTER button.
Highlight the “Street Address” key and press
the ENTER button. A character input screen is
displayed.
Enter the address of your home, highlight the
“OK” key and press the ENTER button. The
map screen is displayed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
Moving the joystick right or left, adjust your
home location if necessary. After adjusting the
location, press the ENTER button.
Ⅲ
Ⅲ
Your home is displayed at the center of the
map. A confirmation message is displayed,
and the system sets your home as the destina-
tion.
Press the MAP button
to return to the
current location map screen. The home icon is
displayed on the screen.
SETTING A STREET ADDRESS AS A DESTINATION
Ⅲ
Ⅲ
Press the DEST button
.
Highlight the “Street Address” key and press
the ENTER button. A character input screen is
displayed.
Ⅲ
Ⅲ
Make sure that the correct region is selected
before inputting the name of the location.
Enter the house number; when finished high-
light the “OK” key and press the ENTER but-
ton. If you do not know the house number,
highlight the “Skip” key and press the ENTER
button.
Ⅲ
Enter the name of the street. After finishing the
entry, highlight the “OK” key and press the
ENTER button. A list of cities is displayed.
Ⅲ
Highlight the correct city of the destination
from the list and press the ENTER button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
The selected destination is displayed at the
center of the map. Highlight the “OK” key and
press the ENTER button after confirming the
location of the displayed destination. The sys-
tem sets the destination to the selected loca-
tion and starts calculating a route.
SETTING A PLACE AS A DESTINATION
Ⅲ
Ⅲ
Press the DEST button
.
A nearby airport is set as a destination in this
example.
Ⅲ
Ⅲ
Highlight the “Points of Interest” key and press
the ENTER button.
Highlight the “Travel” key and press the EN-
TER button.
Ⅲ
Ⅲ
From the category list, highlight the “AIR-
PORT” key and press the ENTER button. A
character input screen appears.
Make sure that the correct region is selected
before inputting the name of the location.
Ⅲ
After inputting the name of the location, high-
light the “OK” key and press the ENTER but-
ton. A list screen appears.
Ⅲ
Highlight the preferred airport key from the list
and press the ENTER button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
The selected destination is displayed at the
center of the map. Highlight the “OK” key after
confirming the location of the displayed desti-
nation, and press the ENTER button. The sys-
tem sets the destination to the selected loca-
tion and starts calculating a route.
BEGINNING ROUTE GUIDANCE
After setting a destination and performing route calculation, the suggested route is displayed.
Ⅲ
Highlight the “OK” key and press the ENTER
button. The system will navigate you through
the guide points using visual and voice guid-
ance.
Ⅲ
Ⅲ
When approaching a guide point, the system
automatically changes to the split screen and
shows an enlarged view of the intersection in
the left screen.
When arriving at the destination, the route
guidance automatically ends.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
SHIFT_
Nissan, the Nissan Brand Symbol, ЉSHIFT_Љ tagline, Z and Nissan model names are Nissan trademarks.
© 2007 Nissan North America, Inc.
QR8E-0Z33U0
Printing: August 2007 (13)
Download from Www.Somanuals.com. All Manuals Search And Download.
|