FLOORTEC R 580 B
DEUTSCH
FRANÇAIS
ENGLISH
BETRIEBSANLEITUNG
MANUEL D’UTILISATION
USER MANUAL
NEDERLANDS
GEBRUIKSAANWIJZING
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
INTRODUCTION ................................................................................................................................... 2
TARGET ........................................................................................................................................................... 2
HOW TO KEEP THIS MANUAL ....................................................................................................................... 2
CHANGES AND IMPROVEMENTS ................................................................................................................. 2
UNPACKING ......................................................................................................................................... 4
DESCRIPTION ................................................................................................................................................. 4
BATTERY CHECK/SETTING ON A NEW MACHINE ...................................................................................... 7
BEFORE START-UP ........................................................................................................................................ 8
MACHINE OPERATION ................................................................................................................................... 9
MACHINE LONG INACTIVITY ....................................................................................................................... 10
FIRST PERIOD OF USE ................................................................................................................................ 10
MAINTENANCE .................................................................................................................................. 10
SCHEDULED MAINTENANCE TABLE .......................................................................................................... 11
MAIN BROOM HEIGHT CHECK AND ADJUSTMENT .................................................................................. 12
MAIN BROOM REPLACEMENT .................................................................................................................... 12
FRAME DUST FILTER CLEANING AND INTEGRITY CHECK ..................................................................... 14
CLOSED POCKET DUST FILTER CLEANING AND INTEGRITY CHECK ................................................... 14
SKIRT HEIGHT AND OPERATION CHECK .................................................................................................. 15
CHARGING THE BATTERIES ....................................................................................................................... 16
TROUBLESHOOTING ........................................................................................................................ 17
146 2601 000(1)2005-03 A
FLOORTEC R 580 B
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
OTHER REFERENCE MANUALS
INTRODUCTION
–
–
Spare Part List, supplied with the machine.
Service manual (that can be consulted at Nilfisk-Alto
Service Centers).
MANUAL PURPOSE AND CONTENTS
The purpose of this Manual is to provide the operator with
all necessary information to use the machine properly in a
safe and autonomous way. It contains information about
technical characteristics, operation, machine storage,
maintenance, spare parts and safety conditions.
Before carrying out any procedure on the machine, the
operators and technicians in charge of the machine
maintenance must read this manual carefully. Contact an
authorised Nilfisk-Alto Service Center in case of doubts
regarding the interpretation of the instructions and for any
further information.
SPARE PARTS AND MAINTENANCE
All necessary operating, maintenance and repair
procedures must be carried out by qualified personnel or
by Nilfisk-Alto Service Centers (listed at the end of this
manual). Only original spare parts and accessories must
be used.
Call Nilfisk-Alto for service or to order spare parts and
accessories, specifying the machine model and serial
number.
TARGET
CHANGES AND IMPROVEMENTS
This manual is intended for qualified operators and
technicians involved in the machine maintenance.
Nilfisk-Alto constantly improves its products and reserves
the right to make changes and improvements at its
discretion without being obliged to apply such benefits to
the machine that were sold previously. Any change and/or
addition of accessory must be approved and performed by
Nilfisk-Alto.
HOW TO KEEP THIS MANUAL
The User manual must be kept near the machine, inside
an adequate case, far from liquids and other substances
that can cause damage to it.
SAFETY
IDENTIFICATION DATA
The following symbols indicate potentially dangerous
situations. Always read this information carefully and take
all necessary precautions to safeguard people and
property.
No accident prevention program is effective without the
total cooperation of the person responsible for the
machine operation. Most of the accidents that may occur
in a factory, while working or moving around, are caused
by failure to comply with the simplest rules for exercising
prudence. A careful and prudent Operator is the best
guarantee against accidents and is essential for
successful completion of any prevention program.
The machine model and serial number are marked on the
outside, under the seat (28, Fig. B).
The machine model year is written in the EC statement
and it is also indicated by the first two figures of the
machine serial number.
This information is useful when requiring machine and
engine replacement parts. Use the following table to write
down the machine identification data for any further
reference.
MACHINE model ........................................................
MACHINE serial number ............................................
2
FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
SYMBOLS
DANGER!
It indicates a dangerous situation with risk
of death for the Operator.
WARNING!
–
–
Carefully read all the instructions before carrying out
any maintenance/repair procedure.
Take all necessary precautions to prevent hair,
jewels and loose clothes from being caught in the
moving parts of the machine.
WARNING!
It indicates a potential risk of injury for
people.
–
–
Do not smoke while charging the batteries.
Do not leave the machine unattended with the key
inserted in the ignition switch and the parking brake
disengaged.
Do not use the machine on surfaces with a gradient
greater than the one indicated on the machine.
Do not wash the machine with direct or pressurised
water jets, or with corrosive substances. Do not use
compressed air for general cleaning, except for the
filters (see the related paragraph).
CAUTION!
It indicates a caution or a remark related to
important or useful functions. Pay attention
to the paragraphs marked by this symbol.
–
–
NOTE
Consult the User manual before performing
any procedure.
–
While using this machine, take care not to cause
damage to other people, especially children.
Do not put any can containing fluids on the machine.
The storage temperature must be between 0°C and
+40°C.
GENERAL INSTRUCTIONS
Specific warnings and cautions to inform about potential
damages to people and machine are shown below.
–
–
–
The machine operating temperature must be
between 0°C and +40°C.
DANGER!
–
–
The humidity must be between 30% and 95%.
Always protect the machine against the sun, rain and
bad weather, both under operation or inactivity
condition.
The machine cannot be used for towing or pushing
objects and/or loads.
Do not use the machine as a transport vehicle; the
machine maximum capacity is 110 kg, besides the
weight of the operator.
Do not allow the brooms to operate while the machine
is stationary to avoid damaging the floor.
In case of fire, possibly use a powder fire
extinguisher, not a water one.
Do not bump into shelves or scaffoldings, particularly
where there is a risk of falling objects.
Adjust the operation speed to suit the floor conditions.
This machine cannot be used on public roads.
Do not tamper with the machine safety guards and
follow the ordinary maintenance instructions
scrupulously.
–
–
–
To perform maintenance/repair procedures turn the
machine ignition key to OFF position and disconnect
the battery.
This machine must be used by properly trained and
authorised personnel only. Children or disabled
people cannot use this machine.
Keep sparks, flames and smoking materials away
from the batteries. During the normal operation
explosive gases are released.
Do not wear jewels when working near electrical
components.
–
–
–
–
–
–
–
–
–
Do not work under the lifted machine, if it is not
securely fixed.
Each time you work under the open hood, ensure that
the hood cannot be closed by accident.
Do not operate the machine near toxic, dangerous,
inflammable and/or explosive powders, liquids or
vapours.
Battery charging produces highly explosive hydrogen
gas. Keep the hood open during battery charging and
perform the operation only in well-ventilated areas
and far from naked flames.
–
–
–
–
–
Do not remove or modify the plates affixed to the
machine by the Manufacturer.
146 2601 000(1)2005-03 A
FLOORTEC R 580 B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
–
In case of machine malfunctions, ensure that these
are not due to lack of maintenance. Otherwise,
request assistance from the authorised personnel or
from an authorised Service Center.
MACHINE DESCRIPTION
OPERATION CAPABILITIES
The sweeper is used to sweep dust or light debris on
smooth and solid floor, in civil or industrial environment,
under safe operation conditions by a qualified Operator.
–
–
In case of part replacement, order ORIGINAL spare
parts from an authorised Dealer or Retailer.
To ensure the proper and safe operation of the
machine, have the scheduled maintenance, detailed
in the related chapter of this Manual, performed by
the authorised personnel or an authorised Service
Center.
The machine must be disposed of properly, because
of the presence of toxic-harmful materials (batteries,
oils, plastics, etc.), which are subject to standards
that require disposal in special centres (see the
“Scrapping” chapter).
If the machine is used according to the instructions,
the vibrations do not cause dangerous situations. The
machine vibration level is less than 2.5 m/s2 (EN
1032-96/A1-98).
Do not tilt the machine more than 30° from its
horizontal position, or the highly corrosive acid could
leak out of the batteries. When the machine is to be
tilted for maintenance operations, remove the
batteries.
CONVENTIONS
Forward, backward, front, rear, left or right are intended
with reference to the operator’s position, that is to say on
the driver’s seat (27, Fig. B).
–
DESCRIPTION
Control panel
(See Fig. B)
1. Hopper lifting/lowering enabling switch
2. Horn switch
3. Working light switch (optional)
4. Position for optional switch (rotating light)
5. Display
–
–
6. Display selection button for the following operations,
in sequence:
- Working hours
- Last digit of the hours - (dot) - minutes
- Battery voltage (V)
UNPACKING
7. Discharged battery warning light (red)
8. Semi-discharged battery warning light (yellow)
9. Charged battery warning light (green)
10. Steering wheel
11. Steering wheel inclination adjusting knobs
12. Emergency stop button
13. Position for optional switch
14. Filter-shaker switch
15. Hopper lifting/lowering switch
16. Hopper overturning switch
17. Vacuum activation/deactivation lever
18. Ignition switch
When the machine is delivered, check that the packing
and the machine were not damaged during transportation.
In case of visible damages, keep the packing and have it
checked by the Parcel Service that delivered it. Call the
Carrier immediately to fill in a damage claim.
Please check that the following items have been supplied
with the machine:
Technical documents:
–
–
–
–
Sweeper manual
Spare Parts List
No. 1 main fuse (F0) 150A
Battery connector
19. Parking brake lock control lever (in combination with
pedal, position 26).
20. Drive pedal
21. Right broom lifting/lowering lever
4
FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
TECHNICAL DATA
22. Left broom lifting/lowering lever (optional)
23. Seat longitudinal position adjusting lever
24. Main broom lifting/lowering lever
25. Front skirt lifting pedal
26. Service brake pedal (parking brake when combined
with lever, position 19)
27. Driver seat with safety microswitch
28. Serial number plate
29. Forward/reverse gear switch
General
Values
Working width (with one side broom)
Working width (with two side brooms)
Machine length
1,050 mm
1,310 mm
1,776 mm
1,207 mm
1,310 mm
1,350 mm
Machine width (with one side broom)
Machine width (with two side brooms)
Maximum height, at the steering wheel
Minimum ground clearance (skirts not
included)
Outside view
(See Fig. C)
1. Pivoting light (always on when the ignition switch is
turned to “I” position)
2. Working light aiming adjusting screws
3. Dust filter cover
60 mm
Hopper maximum lifting height
Maximum weight liftable by the hopper
Minimum/maximum dumping height
Minimum turning radius
1,650 mm
110 kg
270 mm/1,370 mm
1,690 mm
Ø 300 mm x 800 mm
Ø 500 mm
7 Km/h
Main broom size
4. Hopper
5. Left door
Side broom size
Maximum forward speed
Maximum reverse speed
Gradeability
6. Left fastener with locking screw
7. Right opening door
8. Right fastener
9. Working light (optional)
10. Right side broom
11. Left side broom (optional)
12. Main broom
13. Battery compartment hood
14. Rear drive wheels on fixed axis
15. Front steering wheel
16. Left side skirt
3.5 Km/h
16%
Hopper capacity
130 litres
Front axis weight in running conditions
Rear axis weight in running conditions
243 Kg
386 Kg
Machine whole weight with 4x6V 180 Ah
standard batteries
629 Kg
Front steering wheel
Rear wheels, driving
4.00 - 4 mm
4.00 - 4 mm
66.9 dB(A)
Sound level (A Lpa
)
17. Right side skirt
18. Front skirt
19. Rear skirt
Electric motors
Values
Electrical system voltage
24V
24V, 1.100W,
2.800 rpm
20. Dust filter container
Suction/main broom motor
Under-hood compartment
(See Fig. V)
1. Hood (open position)
Drive motor
24V, 750W, 5.000 rpm
24V, 90W, 85 rpm
Side broom reduction unit
Filter-shaker motor
24V, 90W, 5,700 rpm
2. Batteries
3. Battery caps
4. Battery connector
Batteries
Values
No. 4 6V, lead
batteries, with acid
electrolyte, in serial
connection
5. Main broom motor resettable thermal fuse
6. Right side broom motor resettable thermal fuse
7. Left side broom motor resettable thermal fuse
8. Lamellar fuse box
9. Suction/main broom motor
10. Vacuum fan
11. Drive motor
12. Wiring junction box
13. Drive electronic board
14. Hopper lifting system hydraulic oil tank
15. Battery installation diagram
16. Open hood support rod
Standard batteries
No. 1 24V, lead battery
with acid electrolyte
Optional batteries
Optional batteries (gel or lead, available
at Nilfisk retailers)
Values
Battery total voltage
24V
Usable battery capacity
Battery case dimensions
Battery compartment max. size
330Ah
300x800 mm
360x800x380 mm
Dust vacuuming and filtering
Paper dust filter, 5-10 µm
Values
2
4.5 m
Main broom compartment vacuum
7.6 mm H O
2
146 2601 000(1)2005-03 A
FLOORTEC R 580 B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
Wiring diagram
(See Fig. AF)
BE1: Pivoting light (optional)
BZ1: Reverse gear buzzer
Colour code
BK:
BU:
BN:
GN:
GY:
OG:
PK:
RD:
VT:
WH:
Black
Blue
Brown
Green
Grey
Orange
Pink
Red
C1:
Battery connector
EB1: Drive electronic board
EB2: Display board
ES1: Line electromagnetic switch
ES2: Main broom electromagnetic switch
ES3: Pump relay
Violet
White
ES4: Pump relay
F0:
F1:
F2:
F3:
F4:
F5:
F6:
F7:
F8:
F9:
K1:
L1:
L2:
L3:
M1:
M2:
M3:
M4:
M5:
M7:
M8:
R1:
Main fuse
Key fuse
Hydraulic pump fuse
Hopper actuator fuse
Filter-shaker fuse
Hydraulic diagram
(See Fig. AG)
1. Hydraulic oil tank
2. Hydraulic oil filter
3. Hydraulic pump
4. Motor
Service fuse
Working light fuse (optional)
Right side broom resettable thermal fuse
Left side broom resettable thermal fuse (optional)
Main broom resettable thermal fuse
Ignition switch
Right light (optional)
Left light (optional)
Working light (optional)
Drive motor
Main broom motor
Hydraulic pump
Actuator
Filter-shaker motor
Right side broom motor
Left side broom motor (optional)
Accelerator potentiometer (pedal in-built)
5. Safety valve
6. Hopper lifting cylinder
ELECTRICAL FUSES
Under the hood, outside the electrical box, there are the
following fuses:
–
Circuit breakers, which can be reset by pressing
the related key:
–
–
–
Main broom motor (5, Fig. V)
Right side broom motor (6, Fig. V)
Left side broom motor (7, Fig. V) (optional)
–
Lamellar fuses, protected by a transparent plastic
cover, which protect the following circuits:
–
F1 (15A) (the first starting from above): ignition
switch
–
–
–
–
–
–
–
F2 (20A): hydraulic pump
F3 (10A): hopper actuator
F4 (15A): filter-shaker
F5 (10A): auxiliaries
F6 (10A): working lights (optional)
spare 1 (20A)
SW0: Emergency switch
SW1: Forward/reverse gear switch
SW2: Main broom microswitch
SW3: Hopper enabling switch
SW4: Hopper lifting/lowering switch
SW5: Hopper overturning switch
SW7: Right side broom microswitch
SW8: Left side broom microswitch (optional)
SW9: Hopper horizontal position microswitch
SW10: Hopper lifted position microswitch
SW11: Hopper open position microswitch
SW12: Hopper closed position microswitch
SW13: Filter-shaker switch
spare 2 (15A)
Inside the electrical box (12, Fig. V), there is the following
fuse:
–
F0 (150A): main (2, Fig. Z).
ACCESSORIES/OPTIONS
In addition to the standard components, the machine can
be equipped with the following accessories/options,
according to the machine specific use:
SW14: Light switch (optional)
SW15: Horn switch
SW16: Working light switch (optional)
SW17: Safety microswitch (in the seat)
SW18: Accelerator pedal microswitch
–
–
–
–
–
–
–
–
–
Left side broom;
Main and side brooms with harder or softer bristles;
Antistatic polyester or polyester BIA C dust filter;
Pocket filter;
Pivoting light;
Working light;
Non marking skirt;
Non marking wheels;
Protective roof.
For further information concerning the optional
accessories, contact Your Retailer.
6
FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
b) Batteries installed on the machine but dry, that is
without electrolyte.
USE
WARNING!
1. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
2. Remove the battery caps (3, Fig. V).
On some points of the machine there are
some adhesive plates indicating:
–
–
–
–
DANGER
WARNING
CAUTION
NOTE
WARNING!
Be extremely careful when working with
sulphuric acid, as it is corrosive. If it comes
in contact with skin or eyes, rinse
While reading this Manual, the Operator must pay
particular attention to these symbols.
Do not cover these plates for any reason and immediately
replace them if they are damaged.
thoroughly with water and call a physician.
Batteries have to be filled up in a properly
ventilated area. Use protective gloves.
3. Fill the cells (or each element) of the batteries with
sulphuric acid for batteries (density from 1.27 to
1.29 Kg at 25°C) in accordance with the
instructions given in the Battery User's Manual.
The correct quantity of sulphuric acid is indicated
in the Battery Manual.
BATTERY CHECK/SETTING ON A NEW
MACHINE
The machine requires one 24V battery, or four 6V
batteries in serial connection.
Let the battery rest and fill in with sulphuric acid in
accordance with the instructions specified in the
Battery manual.
The machine can be supplied in one of the following
modes:
a) Batteries already installed and ready to be used.
1. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
4. Charge the batteries (see the relevant procedure
in the Maintenance chapter).
c) Without battery
Check that the batteries are connected to the
machine through the related connector (4, Fig. V).
2. Disengage the support rod an lower the hood and
ensure that it is correctly closed.
3. Insert the ignition key (18, Fig. B) in the control
panel and turn it to “I” position (without activating
the forward/reverse gear pedal 20, Fig. B).
If the green warning light (9, Fig. B) turns on, the
battery is ready to be used.
1. Buy appropriate batteries (see the Technical
Characteristics paragraph).
For the battery choice and installation, apply to
qualified battery retailers.
2. Install the batteries and set the battery type (WET
or GEL) on the machine (see the following
paragraph).
3. Charge the batteries (see the relevant procedure
in the Maintenance chapter).
If the yellow or red warning light (8 or 7, Fig. B)
turns on, it is necessary to charge the battery (see
procedure in Maintenance chapter).
146 2601 000(1)2005-03 A
FLOORTEC R 580 B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
BATTERY INSTALLATION AND BATTERY
TYPE SETTING (WET OR GEL)
STARTING AND STOPPING THE MACHINE
Starting the machine
1. Sit in the driver's seat (27, Fig. B) and, using the lever
(23) adjust the seat to a comfortable position.
2. Unlock the steering wheel (10, Fig. B) by means of
the handle (11) and adjust its tilting according to one's
comfort; after the adjustment, release the handle (11)
and lightly move the steering wheel to hook it on the
internal retainer.
3. From the driver's seat (27, Fig. B), insert the key in
the ignition switch (18, Fig. B); turn it to “I” position,
without activating the forward/reverse gear pedal
(20), then wait (for a few seconds) for the display (5,
Fig. B) to turn on and the working hours to appear.
Check that the green warning light turns on (9, Fig.
B).
Battery installation
1. Install the batteries on the machine according to the
diagram (15, Fig. V).
According to the battery dimensions, check if it is
possible to put them inside the related plastic
container, supplied with the machine.
If the batteries dimensions are larger than the
container capacity, use the square guides, supplied
with the machine, to ensure the stability inside the
battery compartment.
WARNING!
Non-sealed lead/acid batteries always need
an appropriate container to prevent the acid
form leaking.
Do not install the non-sealed lead/acid
batteries without an appropriate container.
4. If the warning light becomes red or yellow (7 or 8, Fig.
B) turn the ignition key to “0” position and take it out.
Charge the batteries (see the procedure in the
Maintenance paragraph).
WET or GEL battery setting
NOTE
NOTE
The seat (27, Fig. B) is equipped with a safety
sensor, which allows the machine operation
only if the operator is seated on the driver's
seat.
The machine factory setting is for lead (WET)
batteries. If the setting corresponds to the
chosen battery, do not perform the setting
procedure.
5. Disengage the parking brake by pressing the related
pedal (26, Fig. B) and unlocking the lever (19).
6. To sweep, start the machine with the hands upon the
steering wheel and press the pedal (10, Fig. P).
6a. The forward/reverse direction is selected with the
related switch (29, Fig. B) on the left control panel.
The drive speed can be adjusted from zero to
maximum speed by increasing the pressure exerted
on the pedal.
7. Lower the main broom with the lever (24, Fig. B), then
turn the suction on with the lever (17, Fig. B).
8. Activate the lever (21, Fig. B) to lower the right side
broom.
If not, perform the following procedures:
2. According to the installed battery (WET or GEL),
perform the setting procedure of the machine
electronic board and proceed as follow:
–
–
Turn the ignition switch (18, Fig. B) to “0” position.
Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
–
–
Disconnect the battery connector (4, Fig. V).
Remove the screws (1, Fig. AD) and take out the
right control panel (2) with care.
–
–
Install a jumper wire (1, Fig. AE) on the WET
connectors (2) for lead battery or on the GEL
connectors (3) for gel battery.
Carefully reassemble the control panel (2, Fig.
AD) and fix it by using the related screws (1).
Connect the battery connector (4, Fig. V).
Disengage the support rod (16, Fig. V) and close
the hood (13, Fig. C).
9. Activate the lever (22, Fig. B) to lower the left side
broom, if present.
–
–
NOTE
All brooms (10, 11, 12, Fig. C) can be lifted or
lowered when the machine is moving.
When the brooms are lifted, they do not turn.
When the main broom is lifted, the suction is
not operating.
BEFORE START-UP
1. Check that there are no open doors/hoods and that
the machine is in normal operating conditions.
2. If the machine has not been used yet after the
transportation, check that each block and locking
system used for the transportation, have been
removed.
10. To sweep, start the machine with the hands upon the
steering wheel (10, Fig. B) and press the pedal (20)
correctly.
8
FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
Stopping the machine
HOPPER DUMPING
1. The maximum dumping height of the hopper is 1,380
mm (Fig. U).
2. To empty the hopper, drive the machine near the
dustbin and proceed as follows:
1. To stop the machine, release the pedal (20, Fig. B).
To stop the machine quickly, also push the service
brake pedal (26, Fig. B).
In case of emergency, press the emergency
push-button (12, Fig. B) to immediately stop the
machine. To disengage the safety switch (12), turn it
in the direction indicated by the arrow.
2. Turn the ignition switch (18, Fig. B) to “0” and remove
the key.
–
–
Lift the side and main brooms;
Close the suction by means of the lever (17, Fig.
B);
–
Press the filter-shaker switch (14, Fig. B).
WARNING!
3. Engage the parking brake by pressing the brake
pedal (26, Fig. B) and by activating the brake lock
control lever (19).
Always carry out this operation on a level
ground to avoid machine unbalance.
MACHINE OPERATION
WARNING!
1. Avoid stopping for a long time with the machine in the
same position and the brooms rotating: this could
create unwanted marks on the floor.
2. To collect light and bulky waste materials, lift the front
skirt by activating the pedal (25, Fig. B); do not keep
pushing onto the lever for a long time in order not to
reduce the suction capability of the machine.
When lifting and emptying the hopper (4,
Fig. C), keep the parking brake engaged
with the pedal and lever (26 and 19, Fig. B).
3. Keep people far from the machine and especially
from the hopper (4, Fig. C).
4. Press both the enabling switch (1, Fig. B) and the
hopper lifting switch (15) to lift the hopper (1, Fig. T)
up to the desired position.
WARNING!
When operating on wet grounds, it is
necessary to operate the lever (17, Fig. B)
and turn the suction off to prevent the dust
filter from being damaged.
5. Press both the enabling switch (1, Fig. B) and the
hopper (2, Fig. U) overturning switch (16, Fig. B) and
discharge all the debris in the dustbin (1. Fig. U).
WARNING!
3. For the machine proper operation, the dust filter must
be as clean as possible. To clean it while sweeping,
proceed as follows:
The hopper (2, Fig. U) can be overturned
only after having lifted it at a minimum
height of 270 mm.
–
–
–
Lift the main broom by means of the lever (24, Fig.
B) to stop the suction.
Press the filter-shaker switch (14, Fig. B) at short
intervals.
Then, lower the main broom to restart the suction,
and resume operation.
6. To bring the hopper back to its original position
(horizontal position), press the enabling switch (1,
Fig. B) while pressing the hopper overturning switch
(16. Fig. B).
While working, repeat the operation every 10
minutes (depending on the dustiness of the area
to be cleaned).
NOTE
This operation can also be performed when the
machine is moving.
NOTE
When the dust filter is obstructed and/or the
hopper is full, the machine cannot collect dust
and debris.
4. The hopper (4, Fig. C) should be emptied after each
working period and whenever is full.
146 2601 000(1)2005-03 A
FLOORTEC R 580 B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
7. Press both the enabling switch (1, Fig. B) and the
hopper lowering switch (15) to lower the hopper down
to the desired position.
MAINTENANCE
The lifespan of the machine and its maximum operating
safety are ensured by correct and regular maintenance.
The following chart provides the scheduled maintenance.
The intervals shown may vary according to particular
working conditions, which are to be defined by the person
in charge of the maintenance.
WARNING!
The hopper can be overturned only if it is
not in its original position (horizontal
position).
8. The machine is ready to start working again.
WARNING!
Operations to be carried out with the
machine off, the ignition key not inserted
and (if required) the battery disconnected.
Moreover, carefully read the instructions in
the Safety chapter.
AFTER USING THE MACHINE
After working, before leaving the machine:
–
–
Lift the main broom with the lever (24, Fig. B).
Lift the side brooms with the levers (21 and 22, Fig.
B).
All scheduled or extraordinary maintenance operations
must be performed by qualified personnel, or by an
authorised Service Center.
This manual describes only the easier and most common
maintenance procedures.
–
–
Close the suction by means of the related lever (17,
Fig. B), then press the filter-shaker switch (14, Fig. B)
for a short interval; open the suction again.
Dump the hopper (4, Fig. C) (see previous
paragraph).
–
–
Remove the ignition key from the switch (18, Fig. B).
Engage the parking brake by pressing the brake
pedal (26, Fig. B), then activate the brake lock control
lever (19).
NOTE
For other maintenance procedures contained
in the Scheduled Maintenance Table or for
extraordinary maintenance operations see the
specific Service Manual that can be consulted
at any Service Center.
WORKING LIGHT ADJUSTMENT
If necessary, adjust the working light (9, Fig. C) beam
aiming with the screws (22).
MACHINE LONG INACTIVITY
If you foresee that the machine will not be used for more
than 30 days, proceed as follows:
–
Check that the machine storage area is dry and
clean.
–
Disconnect the battery connector (4, Fig. V).
FIRST PERIOD OF USE
After the first period of use (first 8 hours) it is necessary to
check that the fixing and connecting elements are
correctly tightened, that the visible parts are integral and
that there are no leakages.
10 FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
SCHEDULED MAINTENANCE TABLE
Every 10
hours
Every 50
hours
Every 100
hours
Every 200
hours
Every 400
hours
Maintenance operation
Battery fluid level check
On delivery
(1)
Hopper lifting hydraulic system oil level check
(1)
Motor-to-main broom belt visual inspection and
tension check
(*)
Skirt height and operation check
Side and main broom height check
Frame dust filter cleaning and integrity check
Closed pocket filter cleaning and integrity
check
Filter-shaker operation check
Brake adjustment
(*)
(*)
(*)
Nut and screw tightening check
(*) (2)
Drive wheel gearing chain tension check and
cleaning
Steering chain cleaning
(*)
(*)
Vacuum hose integrity check
Pulley-to-main broom belt replacement
(*)
(*)
(*)
(*)
Motor-to-main broom pulley V-belt
replacement
Hopper gasket integrity check
Hopper lifted position control microswitch
adjustment check
Hopper horizontal position control micro-switch
adjustment check
(*)
Motor carbon brush check and replacement
Hydraulic oil change
(*)
(*) (3)
(*): For the related procedure, see the Service Manual
(1): or before each start-up
(2): And after the first 8 running-in hours
(3): replace hydraulic oil for the first time after 500 hours, then after 2,000 hours or every year.
146 2601 000(1)2005-03 A
FLOORTEC R 580 B 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
10. Engage the retainer (6, Fig. C) and close the left door
(5).
MAIN BROOM HEIGHT CHECK AND
ADJUSTMENT
NOTE
NOTE
If it is not possible to adjust the print (1, Fig. D)
correctly, because the ground pressure at the
ends of the broom is different, refer to the
Service Manual for the related adjustment
procedure.
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
1. Check the main broom for proper ground clearance,
proceeding as follows:
–
–
Drive the machine on a level ground;
Keep the machine stationary and rotate the main
broom for a few seconds;
MAIN BROOM REPLACEMENT
NOTE
–
–
Stop and lift the main broom, then move the
machine;
Check that the main broom print (1, Fig. D), along
its length, is from 2 to 4 cm wide.
If the print (1) is not within specifications, it is
necessary to adjust the broom height, proceeding
as described in the following steps.
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
WARNING!
It is advisable to use protective gloves
when replacing the main broom because
there can be cutting debris between the
bristles.
2. To stop the machine, turn the ignition switch (18, Fig.
B) to “0” position.
1. Drive the machine on a level ground and activate the
parking brake using the pedal and the lever (26 and
19, Fig. B).
2. Turn the ignition switch (18, Fig. B) to “0” position.
3. Open the hood (1, Fig. V) and disconnect the battery
connector (4, Fig. V).
WARNING!
Before opening the left door (5, Fig. C)
switch the machine off to prevent the belts
and pulleys rotation.
3. Remove the screw with a screwdriver, then release
the fastener (6, Fig. C).
4. Open the left door (5, Fig. C).
4. Disengage the retainer (8, Fig. C) and open the right
door (7).
5. Loose the locknut (2, Fig. E).
6. Turn the handwheel (1, Fig E) and remind that:
5. Unscrew and remove the knobs (1, Fig. F).
6. Remove the broom compartment cover (1, Fig. G).
7. Remove the broom (1, Fig. H).
8. Check that the drive hub (1, Fig. I) is free from dirt or
foreign materials (ropes, rags, etc.) accidentally
rolled up.
–
to decrease the pressure of the broom on the
ground, it must be screwed.
–
to increase the pressure of the broom on the
ground, it must be unscrewed.
9. The new broom must be installed with the bristles
rows positioned as shown in the figure (2, Fig. I).
10. Install the new broom (3, Fig. I) on the machine and
ensure that its mesh (4) correctly fits on the related
drive hub (1).
NOTE
When the handwheel is completely
unscrewed, you have reached the maximum
pressure of the broom on the ground.
11. Reinstall the broom compartment cover (1, Fig. G)
and screw the knobs (1, Fig. F).
12. Engage the retainer (8, Fig. C) and close the right
door (7).
13. Carry out the main broom height check and
adjustment, as described in the previous paragraph.
7. Screw the locknut (2, Fig. E).
8. Perform step 1 again to check the proper adjustment
of the main broom height from the ground.
9. When the broom is too worn to be adjusted, replace it
as shown in the next paragraph.
12 FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
SIDE BROOM HEIGHT CHECK AND
ADJUSTMENT
SIDE BROOM REPLACEMENT
NOTE
Brooms of various hardness are available. This
NOTE
procedure is applicable to all types of brooms.
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
WARNING!
1. Check the side brooms for proper ground clearance,
proceeding as follows:
It is advisable to use protective gloves
when replacing the side broom because
there can be cutting debris between the
bristles.
–
–
Drive the machine on a level ground;
Keep the machine stationary, lower the side
brooms and rotate them for a few seconds;
Stop and lift the side brooms, then move the
machine;
Check that the side broom prints are, in extension
and orientation, as shown in the figure (1 and 2,
Fig. J).
1. Drive the machine on a level ground and activate the
parking brake using the pedal and the lever (26 and
19, Fig. B).
2. Turn the ignition switch (18, Fig. B) to “0” position.
3. Activate the lever (21 or 22, Fig. B) to lift the related
side broom.
4. From the inside of the side broom, unscrew the 4 nuts
(1, Fig. L), then remove the broom and the hub (2) by
disengaging it from the shaft (3).
Recover the key (4) and the washer (5).
5. At the bench, remove the four screws (6) and
separate the broom (8) from the hub (7).
6. Install the new broom (8) onto the hub (7), and tighten
the screws (6).
–
–
In case the prints are not within specifications, it is
necessary to adjust the broom height, proceeding
as described in the following steps.
2. Engage the parking brake using the pedal and the
lever (26 and 19, Fig. B).
3. Turn the ignition switch (18, Fig. B) to “0” position.
4. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
5. For the right side broom, use the lever (1, Fig. K):
loosen the ring nut (2) and adjust the register (3) until
the correct print is achieved (1. Fig. J). Then fit it on
the lever by means of the ring nut (2, Fig. K).
For the left side broom, use the lever (4, Fig. K):
Loosen the ring nut (5, Fig. J) and adjust the adjuster
(6) until the correct print (2) is achieved. Then fit it on
the lever by means of the ring nut (5, Fig. K).
6. Perform step 1 again to check the proper adjustment
of the side broom height from the ground.
7. Reinstall the new broom with the hub (2) on the
machine after seating the key (4). Position the washer
(5) and tighten the screw (1).
8. Carry out the side broom height check and
adjustment, as described in the previous paragraph.
7. When the broom is too worn to be adjusted, replace it
as shown in the next paragraph.
NOTE
If necessary, adjust also the side brooms tilting
position (see the related procedure on the
Service Manual).
146 2601 000(1)2005-03 A
FLOORTEC R 580 B 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
FRAME DUST FILTER CLEANING AND
INTEGRITY CHECK
CLOSED POCKET DUST FILTER
CLEANING AND INTEGRITY CHECK
NOTE
NOTE
Besides the standard paper filter, optional
polyester filters are also available. The
following procedure is applicable to each type
of filter.
The polyester closed pocket filters are normally
kept clean by activating the electric
filter-shaker supplied with the machine.
If necessary, they can be cleaned using the
procedure indicated below.
1. Drive the machine on a level ground and activate the
parking brake using the pedal and the lever (26 and
19, Fig. B).
When the filtration surfaces are no longer
suitable, the filter must be replaced.
2. Turn the ignition switch (18, Fig. B) to “0” position.
3. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
1. Drive the machine on a level ground and activate the
parking brake using the pedal and the lever (26 and
19, Fig. B).
4. Disconnect the battery connector (4, Fig. V).
Remove the filter cover (2, Fig. M) by disengaging it
from the retainers (1).
2. Turn the ignition switch (18, Fig. B) to “0” position.
3. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
5. Disconnect the electric connector (1, Fig. N) from the
filter-shaker.
4. Remove the filter cover (2, Fig. M) by disengaging it
from the retainers (1).
6. Remove the filter-shaker support frame handwheels
(2, Fig. N).
5. Unscrew the knobs (1, Fig. AA) and remove the
brackets (2).
7. Remove the filter-shaker support frame (3, Fig. N).
8. Pull out the dust filter (4, Fig. N) upwards.
9. In an appropriate outdoor area, clean the filter
shaking it on a level and clean surface, tapping the
side (1, Fig. O), opposite the wire gauze (2).
Complete the cleaning by using compressed air (3) at
max. 6 bars, blowing only from the side protected by
the wire gauze (2), at a minimum distance of 30 cm.
According to the filter type, observe the following
cautions:
6. Pull out the dust filter (1, Fig. AB) upward, and
remove it after disconnecting the electrical connector
(2) from the filter-shaker.
7. Disassemble the polyester filtering surface, as
indicated by the following steps; these procedures
must be carried out in a suitable outdoor area and the
Operator must be suitably equipped (gloves, mask,
glasses).
8. Remove the filter-shaker motor (1, Fig. AC) by
unscrewing the two fixing screws.
–
Paper filter (standard): do not use water or
detergents to clean it; the filter can be damaged;
Polyester filter (optional): To clean it, see the
above-mentioned instructions. If necessary, for a
better cleaning, it is allowed to wash the filter with
water and non-lathering detergents. This provides
better quality cleaning but reduces the life of the
filter, which will have to be replaced more
frequently. The use of inadequate detergents can
damage the filter.
9. Open the filter-shaker motor support unit (2, Fig. AC)
completely and release the filtering pocket tension
rods (3).
10. Remove all the filtering pocket tension rods (4, Fig.
AC).
11. Open the upper retaining cord (5, Fig. AC) of the
closed pocket filter to remove it from the upper frame
(6).
12. Remove the internal pocket separator (7, Fig. AC).
13. Clean the polyester fiber surface (8, Fig. AC) from the
dirty side, using an external vacuum cleaner,
spreading it out completely or cleaning pocket by
pocket. At the same time, clean both the surfaces of
the pocket separator (7, Fig. AC) removing anything
deposited on them. Check the filtering surface for
tears. In case of tears, replace it. It is also possible to
use compressed air (max. 6 bars), blowing the air
from the clean side towards the dirty side.
–
Check the filter body for tears.
10. Clean the filter compartment rubber seal (1, Fig. P)
along its perimeter and check its integrity. If
necessary, replace it.
11. Install in the reverse order of removal (steps from 8 to
1).
NOTE
When reinstalling the filter, the wire gauze (2,
Fig. O) must be facing upward.
WARNING!
Do not wash the filter with water. The
polyester fibber can shrink and become
unusable.
14 FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
14. Reassemble all the filter components in the reverse
order of disassembly.
15. If necessary, clean the filter compartment rubber seal
(3, Fig. AB) along its perimeter and check its integrity.
If necessary, replace it.
10. Press the front (25, Fig. B) skirt lifting pedal
completely, and check that the front skirt lifts 5 cm
approximately.
Release the pedal and check that the skirt returns to
the initial position and not in an intermediate position.
If necessary, adjust the skirt lifting cable (1, Fig. X), by
means of the adjuster (2) on the left front side of the
skirt (for the front skirt control cable replacement, see
the Service Manual).
16. Reassemble all the components in the reverse order
of disassembly.
SKIRT HEIGHT AND OPERATION CHECK
11. Reassemble in the reverse order of disassembly.
Side skirts
1. Drive the machine on a level ground that is suitable
for checking the skirt height.
2. Engage the parking brake using the pedal and the
lever (26 and 19, Fig. B).
3. Turn the ignition switch (18, Fig. B) to “0” position.
4. Disengage the retainers (8 and 6, Fig. C) and open
the right and left doors (7 and 5).
5. Check the side skirt (2, Fig. F) integrity.
Replace the skirts when they have cuts (1, Fig. Q)
larger than 20 mm or cracks/tears (2) larger than 10
mm (for skirt replacement, see the Service Manual).
6. Check that side skirt (2, Fig. F) height from ground is
within 0 – 3 mm (Fig. R).
HOPPER LIFTING SYSTEM OIL LEVEL
CHECK
WARNING!
These operations must be performed with
the hopper (4, Fig. C) in its original position
(as shown in the figure).
1. Engage the parking brake using the pedal and the
lever (26 and 19, Fig. B).
2. Lift the hood (1, Fig. V) and secure it with the rod (16).
3. Check that the hydraulic oil level in the tank (14, Fig.
V) is between the MIN (minimum level) and MAX
(maximum level) marks shown in figure Y.
4. If necessary, add hydraulic oil - viscosity grade 32 cSt
- through the plug (1, Fig. Y).
After loosening the screws (3, Fig. F), if necessary,
adjust the skirt position. Then tighten the screws (3).
Front and rear skirt
7. Remove the main broom, as described in the related
paragraph.
5. Disengage the support rod (16, Fig. V) and close the
hood (1).
8. Check the front (1, Fig. W) and rear (2) skirts for
integrity.
Replace the skirts when they have cuts (1, Fig. Q)
larger than 20 mm or cracks/tears (2) larger than 10
mm (for skirt replacement, see the Service Manual).
9. Check that the front (1, Fig. W) and rear (2) skirts rub
lightly on the floor but are not completely lifted from
the ground (Fig. S).
After loosening the screws (3, Fig. W), adjust the skirt
position if necessary. Then tighten the screws (3).
146 2601 000(1)2005-03 A
FLOORTEC R 580 B 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
CHARGING THE BATTERIES
SAFETY FUNCTIONS
WARNING!
The machine is equipped with the following safety
functions.
Battery charging produces highly
explosive hydrogen gas. Charge the
batteries in well-ventilated areas and away
from naked flames. Do not smoke while
charging the batteries. Keep the hood open
while recharging the battery.
RUNNING ENABLING SWITCH
It allows the machine to run only if the operator is on the
driver's seat (27, Fig. B).
EMERGENCY PUSH-BUTTON
WARNING!
It is located in an easily accessible position (12, Fig. B); it
has to be pressed in case of emergency, to stop all the
machine functions.
Be extremely careful when charging the
battery as there may be battery fluid
leakages. The battery liquid is corrosive. If
it comes in contact with the skin or eyes,
rinse thoroughly with water and consult a
physician.
HOPPER LIFTING/LOWERING AND
OVERTURNING ENABLING SWITCH
It is in the position (1, Fig. B) and must be pressed and
held to activate the hopper lifting/lowering and overturning
switches.
1. Drive the machine on a level ground and activate the
parking brake using the pedal and the lever (26 and
19, Fig. B).
2. Turn the ignition switch (18, Fig. B) to “0” position.
3. Lift the hood (13, Fig. C) and secure it with the rod
(16, Fig. V).
4. Check the correct level of electrolyte inside the
battery; if necessary, top up through the caps (3, Fig.
V).
Leave the caps (3) open for the next battery charge.
If necessary, clean the upper surface of the batteries.
5. Check that the battery charger is appropriate,
referring to its instructions.
HOPPER LIFTING CYLINDER SAFETY
DEVICE VALVE
It is located on the hopper lifting cylinder.
It stops the hopper in the position it has reached (without
possibility for it to lower accidentally) if the hydraulic
system piping, feeding the lifting cylinder should break.
The battery charger voltage rating is 24 V.
Use a battery charger suitable for the type of batteries
installed.
6. Disconnect the battery connector (4, Fig. V) and
connect it to the external battery charger.
7. Connect the battery charger to the electrical system
and charge the batteries.
8. When the recharging is complete, disconnect the
battery charger from the electrical system and from
the battery connector (4, Fig. V).
9. Check the correct level of electrolyte inside the
batteries and close the caps (3, Fig. V).
10. Reconnect the battery connector (4, Fig. V) to the
machine.
11. Disengage the support rod (16, Fig. V) and close the
hood (13, Fig. C): the machine is ready to be used.
16 FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
TROUBLESHOOTING
SCRAPPING
TROUBLE
REMEDY
Have the machine scrapped by a qualified scrapper.
Before scrapping the machine, remove the following
components:
Check that the battery
connector (4, Fig. V) is correctly
connected to the machine.
After having turned the ignition
key (18, Fig. B) to “I” position, the
display does not illuminate and
the machine does not work.
–
–
–
–
–
–
–
Battery
Check the F1 (1, Fig. Z) and F0
(2, Fig. Z) fuse integrity
Polyester dust filter
Main and side brooms
Hydraulic oil
Hydraulic oil filter
Electronic boards
Plastic components and hoses
Turn the ignition switch to “0”
position, then turn it to “I”
position being careful not to
activate the accelerator pedal
during this operation
The machine does not move
when pressing the accelerator
pedal.
Check that the related fuse (5,
Fig. V) is not deactivated;
otherwise reactivate it by means
of the related key
WARNING!
The main broom does not work
The side brooms do not work
The removed components must be
disposed of properly according to the Law
in force.
Check that the related fuse (6 or
7, Fig. V) is not deactivated;
otherwise reactivate it by means
of the related key
The machine operates only when Re-charge the battery. If the
stationary, otherwise the red
warning light turns on.
problem persists, replace the
battery.
Check if the dust filter (4, Fig. N)
is clogged
Check if the hopper (4, Fig. C) is
full
The machine collects little
debris/dust
Check that the skirts (16, 17, 18,
19, Fig. C) are not broken or
incorrectly adjusted
Check if the brooms (10, 11, 12,
Fig. C) are at the correct height
Install a battery with greater
capacity: 240 Ah
The battery autonomy is low
The hopper does not lift
Check the fuse (F2, Fig. Z)
integrity
Check the fuse (F3, Fig. Z)
integrity
The hopper does not lift
Check that the hopper is lifted
from the ground at an height
greater than 270 mm
Before lowering the hopper by
means of the related switch (15,
Fig. B), check that the hopper
has returned to the horizontal
position by means of the related
switch (16, Fig. B).
The hopper does not lower
Check that the main broom is
lifted with the lever (24, Fig. B)
The filter-shaker does not work
Check the fuse (F4, Fig. Z)
integrity
For further information, refer to the Service Manual,
available at any Nilfisk-Alto Service Center.
146 2601 000(1)2005-03 A
FLOORTEC R 580 B 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
EC CERTIFICATE OF CONFORMITY
$OWRꢀ'HXWVFKODQGꢀ*PE+
'ꢁꢃꢄꢂꢃꢅꢀ%HOOHQEHUJ
3URGXFWꢀ
6ZHHSHU
ꢂꢉ9
7KHꢁGHVLJQꢁRIꢁWKHꢁDSSOLDQFHꢁFRUUHVSRQGV
WRꢁWKHꢁIROORZLQJꢁSHUWLQHQWꢁUHJXODWLRQVꢀ
(&ꢀ/RZꢀ9ROWDJHꢀ'LUHFWLYHꢀꢅꢋꢊꢂꢋꢊ((&
(&ꢀ(0&ꢀ'LUHFWLYHꢀꢃꢄꢊꢋꢋꢌꢊ((&
$SSOLHGꢁKDUPRQL]HGꢁVWDQGDUGVꢀ
(1ꢀꢍꢂꢍꢈꢈꢁꢍꢎ(1ꢀꢍꢂꢍꢈꢈꢁꢂꢎ(1ꢀꢂꢄꢉꢎ(1ꢀꢋꢉꢄ
(1ꢀꢇꢇꢈꢍꢉꢁꢍꢎꢀ(1ꢀꢇꢇꢈꢍꢉꢁꢂ
$SSOLHGꢁQDWLRQDOꢁVWDQGDUGVꢁDQGꢁWHFKQLFDO
VSHFLILFDWLRQVꢀ
,(&ꢀꢌꢈꢋꢋꢇꢁꢂꢁꢅꢂ
'LSOꢆꢁ,QJꢆꢀ:ROIJDQJꢀ1LHXZNDPS
7HVWVꢀDQGꢀDSSURYDOV
%HOOHQEHUJꢎꢀꢍꢍꢆꢈꢂꢆꢂꢈꢈꢇ
18 FLOORTEC R 580 B
146 2601 000(1)2005-03 A
Download from Www.Somanuals.com. All Manuals Search And Download.
AF
SW14
SW15
L1
YEBK
VT
CL1
BE1
BK
BK
SW13
BN
M5
0V
SW10
SW11
SW12
apre
PK
BU
PK
BU
RD
BU
M4
0V
SW5
VT
VT
chiude
WHBK
SW4
WH
GY
SW9
GYBK
GY
GYBK
ES4
OG
ES3
0V
0V
M3
RD
BK
SW3
SW8
BK
0V
BNBK
SW7
GYBK
WHBK
SW2
VTBK
BN
OGBK
OG
OGBK
0V
F6
F5
F4
F3
F2
YE
OG
YE
BK
ES2
BK
BU
VT
0V
WH
RD
M2
M7
GY
M8
RD
RD
A
BN
EB2
K1
A
A
SW0
F1
F0
RD
RD
F8
F9
F7
OG
RD
RD
0V
ES1
RD
BK
RD
RD
EB1
M1
OG
RD
PK
-
C1
SW17
SW18
VT
BN
0V
SW1
0V
BZ1
VT
-
OG
BU
0V
24V BATTERIES
WH
OG
R1
S310215
Download from Www.Somanuals.com. All Manuals Search And Download.
AG
200 BAR
70 BAR
750cc / HYDRAULIC OIL 32 cSt
S310132
Download from Www.Somanuals.com. All Manuals Search And Download.
M
O
Q
T
N
V
S310121
S310124
S310037
S310125
S310122
S310192
S310039
S310126
P
R
S
S310212
S310038
W
X
U
S310127
S310128
Download from Www.Somanuals.com. All Manuals Search And Download.
Y
Z
Nilfisk-ALTO
HEADQUARTER
DENMARK
Nilfisk-Advance Group
Sognevej 25
2605 Brøndby
Denmark
Tel: (+45) 43 23 81 00
SUBSIDIARIES
AUSTRALIA
Nilfisk - ALTO
GERMANY
Nilfisk-ALTO
SPAIN
Nilfisk-ALTO
48 Egerton St.
PO box 6046
Silverwater NSW 2128
Australia
Tel: (+61) 2 8748 5966
Fax: (+61) 2 8748 5960
Division of Nilfisk-Advance A/S
Guido-Oberdorfer-Str. 2-8
89287 Bellenberg
Division of Nilfisk-Advance S.A.
Torre D´Ara
Paseo del Rengle, 5 Pl. 10
08302 Mataró Barcelona
Spain
Tel: (+34) 93 741 24 00
Fax : (+34) 93 757 80 20
E-mail: info@nilfisk-alto.es
Germany
S310129
S310130
S310187
S310213
Tel: (+49) (0) 730 67 20
Fax: (+49) (0) 730 67 23 10
E-mail: info@nilfisk-alto.de
Info-export@nilfisk-alto.de
AA
AB
AD
AE
AUSTRIA
ALTO Österreich GmbH
Nilfisk-Advance AG
Metzgerstrasse 68
5101 Bergheim/Salzburg
Austria
Tel : (+43) 662 456 400 11
Fax: (+43) 662 456 400 34
E-mail: verkauf@nilfisk-alto.at
GREAT BRITAIN
Nilfisk-ALTO
Division of Nilfisk-Advance Ltd.
Bowerbank Way
Gilwilly Industrial Estate
Penrith Cumbria CA11 9BQ
Great Britain
Tel: (+44) 1 768 86 89 95
Fax: (+44) 1 768 86 47 13
E-mail: sales@nilfisk-alto.co.uk
SWEDEN
ALTO Sverige AB
Aminogatan 18, Box 40 29
431 04 Mölndal
Sweden
Tel: (+46) 31 706 73 00
Fax: (+46) 31 7067341
E-mail: info@nilfisk-alto.se
BRAZIL
Wap do Brasil Ltda.
Rua das Palmeiras,
USA
ALTO U.S. Inc.
16253 Swingley Ridge Road
Suite 200
Chesterfield
Missouri 63017-1544
USA
350-Bairro Capela Velha
83.705-500 – Araucária - Paraná
Brasil
Tel: (+55) 41 2106 7400
Fax (+55) 41 2106 7403/7404
E-mail: [email protected]
HUNGARY
ALTO Hungary Kft
Csengery ut. 119
8800 Nagykanizsa
Hungary
Tel: (+36) 93 509 701
Fax: (+36) 93 509 704
Tel.: (+1) 636 530 0871
Fax: (+1) 636 530 0872
E-mail: [email protected]
CANADA
ALTO Canada
24 Constellation Road
Rexdale
Ontario M9W 1K1
Canada
Tel: (+1) 416 675 5830
Fax: (+1) 416 675 6989
MALAYSIA
ALTO DEN-SIN Malaysia Sdn Bhd
SD14, Jalan KIP 11
S310186
ALTO U.S.Inc
2100 Highway 265
Springdale
Arkansas 72764
USA
Tel: (+1) 479 750 1000
Fax: (+1) 479 756 0719
E-mail: [email protected]
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Malaysia
Tel: (+603) 6274 6913
Fax: (+603) 6274 6318
E-mail: [email protected]
7
AC
5
2
CZECH REPUBLIC
ALTO Ceskà republika s.r.o.
Zateckých 9
14000 Praha 4
Czech Republic
Tel. (+420) 24 14 08 419
Fax (+420) 24 14 08 439
E-mail: [email protected]
ALTO U.S.Inc
1100 Haskins Road
Bowling Green
1
NETHERLANDS
Nilfisk-ALTO
ALTO Nederland B.V.
Camerastraat 9
1
Ohio 43402
USA
1322 BB Almere
The Netherlands
Tel: (+31) 36 5460 760
Fax: (+31) 36 5460 700
E-mail: [email protected]
Postbox 60112
Tel: (+1) 419 352 75 11
Fax: (+1) 419 353 71 87
E-Mail: [email protected]
DENMARK
Nilfisk-ALTO
Division of Nilfisk-Advance A/S
Industrivej 1
ALTO Cleaning Systems, Inc.
12249 Nations Ford Road
Pineville
1
9560 Hadsund
Denmark
1320 AC Almere
1
Tel: (+45) 72 18 21 00
Fax: (+45) 72 18 21 05
E-mail: salg@nilfisk-alto.dk
E-mail: service@nilfisk-alto.dk
The Netherlands
North Carolina 28134
USA
Tel: (+1) 704 971 1240
Fax: (+1) 704 971 1241
E-mail: info@nilfisk-advance.us
NORWAY
ALTO Norge AS
Bjørnerudveien 24
1266 Oslo
8
Nilfisk-ALTO Food Division
Division of Nilfisk-Advance A/S
Blytækkervej 2,
Norway
Tel: (+47) 22 75 17 70
Fax: (+47) 22 75 17 71
E-mail: info@nilfisk-alto.no
6
3
9000 Aalborg
Denmark
Tel: (+45) 72 18 21 00
Fax: (+45) 72 18 20 99
E-mail: scanio.technology@nilfisk-alto.dk
4
2
SINGAPORE
ALTO DEN-SIN
Singapore Pte. Ltd.
No. 17 Link Road
FRANCE
Nilfisk-ALTO
ALTO France SA
Aéroparc 1
19 rue Icare
67960 Entzheim
France
Singapore 619034
Singapore
Tel: (+65) 6268 1006
Fax: (+65) 6268 4916
E-mail: [email protected]
Tel: (+33) 3 88 28 84 00
Fax: (+33) 3 88 30 05 00
E-mail: info@nilfisk-alto-fr
1
S310145
S310214
Download from Www.Somanuals.com. All Manuals Search And Download.
|