User's Manual
ELVIS Series
R
Version 1.0 July 2003
English
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENT
1. QUICK START - PASSIVE SPEAKER CABINET....................................................................................3
-. For Passive Full-range Speakers
-. For Passive Subwoofer & Satellite Speakers
2. QUICK START - ACTIVE SPEAKER CABINET.....................................................................................5
-. For Active Full-range Speakers
-. For Active Subwoofer & Satellite Speakers
3. CONNECTION PLATE...........................................................................................................................7
-. PASSIVE FULL-RANGE Speaker for ELVIS10/ELVIS12/ELVIS15/ELVIS12M
-. PASSIVE SUBWOOFER Speaker for ELVIS12S/ELVIS15S
-. Active FULL-RANGE Speaker for ELVIS10A/ELVIS12/AELVIS15A/ELVIS12MA
-. Active SUBWOOFER Speaker for ELVIS12SA/ELVIS15SA
4. WIRE CONNECTIONS .........................................................................................................................10
-. For Passive Speaker Cabinets
-. For Active Speaker Cabinets
5. ELVIS TECHNICAL SPECIFICATIONS.................................................................................................11
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. QUICK START - PASSIVE SPEAKER CABINET
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely
down.
-. For Passive Full-range Speakers
1). Connect one side of the speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier
and the other side to the Input socket of your speaker cabinet.
2). Complete other connections as illustrated.
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume controls of your amplifier to about 70%.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
6). After using, turn off your stereo power amplifier first, then the mixer.
QUICK START
Elvis Passive Full-range Speakers
speaker cable
speaker cable
Stereo
Power Amplifier
Left
Right
Tripod
Mount
Tripod
Mount
Main Mix
Output
Main Mix
Output
Mixer
3
Download from Www.Somanuals.com. All Manuals Search And Download.
-. For Passive Subwoofer & Satellite Speakers
1). Connect one side of speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier and the other
side to the Input socket of your subwoofer, with the second speaker cable connect the Output of the subwoofer to the
Input of satellite.
2). Complete other connections as illustrated.
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume controls of your amplifier to about 70%.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
6). After using, turn off your stereo power amplifier first, then the mixer.
QUICK START
ELVIS Passive Subwoofer & Satellite Speakers
Speaker Cable
Speaker Cable
pole
pole
Mount
Mount
Speaker Cable
Speaker Cable
Stereo
Power Amplifier
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. QUICK START - ACTIVE SPEAKER CABINET
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely
down.
-. For Active Full-range Speakers
1). Connect one side of the signal cable at your audio mixer in to Output Left /Right (with Stereo-Jack or XLR) and
the other side of the cable in to the Line Input (COMBO) of your active speaker cabinet (with Stereo-Jack or XLR).
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control fo the active speaker cabinets.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the
output level.
6). After using, turn off your active speaker cabinets first, then the mixer.
QUICK START
Elvis Active Full-range Speakers
Signal Cable
Signal Cable
Power Cord
Power Cord
Left
Main Mix
Output
Right
Main Mix
Output
Tripod
Mount
Tripod
Mount
Mixer
5
Download from Www.Somanuals.com. All Manuals Search And Download.
-. For Active Subwoofer & Satellite Speakers
1). Connect one side of signal cable at your audio mixer in to Output Left /Right (with Stereo-Jack or XLR) and the other
side of the cable in to the Left / Mono Input (COMBO) of the active subwoofer; with the second signal cable connect
the Left Output of the subwoofer (Stereo/Mono-Jack or XLR) to the Line Input (COMBO) of the active satellite (with
Stereo - Jack or XLR).
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control fo the active speaker cabinets.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the
output level.
6). After using, turn off your active speaker cabinets first, then the mixer.
QUICK START
Elvis Active Subwoofer & Satellite Speakers
Signal Cable
Power Cord
Tripod
Mount
Tripod
Mount
Signal Cable
Left
Main Mix
Output
Right
Main Mix
Output
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. CONNECTION PLATE
- PASSIVE FULL-RANGE Speaker for ELVIS10 / ELVIS12 / ELVIS15 / ELVIS12M
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2/-2 not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2/-2 not connected).
ELVIS 12
SOUND REINFORCEMENT SPEAKER SYSTEM
Power Handling:
AES - 180 Watts
PEAK - 360 Watts
IMPEDANCE:
8 ohms nominal
MODEL
SERIAL
DESIGNED AND DEVELOPMENT IN ITALY
INPUT
THRU
LINK
(2)
(1)
- PASSIVE SUBWOOFER Speaker for ELVIS12S / ELVIS15S
(1) INPUT: Receive the power coming from an external amplifier (SPK +1/-1 connected;+2/-2 not connected).
(2) OUTPUT: Power output for satellite speaker, under passive crossover filtered at 125Hz (SPK +1/-1 connected;
+2/-2 not connected).
ELVIS 12S
POWER HANDLING:
AES - 200 Watts
PEAK - 400 Watts
IMPEDANCE:
4 ohms nominal
MODEL
SERIAL
DESIGNED AND DEVELOPMENT IN ITALY
INPUT
OUTPUT
(1)
(2)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
-. ACTIVE FULL- RANGE Speaker for ELVIS10A / ELVIS12A / ELVIS15A / ELVIS12MA
(1) Bi-polar main power switch.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
(4) POWER, blue LED, indicate ON status.
(5) SIGN / COMP, signal/compressor, green/red LED
(6) LINE OUT at + 4dB on XLR connector
(7) LINE IN at + 4dB on COMBO connector.
(8) VOLUME main power amplifier control.
(9) LOW / MID / HIGH, EQ tone control at +/- 6dB.
(10) GAIN control for microphone -10/- 45dB.
(11) MIC IN on balanced XLR, for microphone.
MIC IN
(11)
(10)
MIC GAIN
-10dB
-45dB
HIGH
-6dB
-6dB
-6dB
+6dB
+6dB
+6dB
(9)
MIDDLE
LOW
VOLUME
(8)
(7)
-
+4dBu
LINE-IN
MODEL
SERIAL
LINE-OUT
(6)
(3)
AC INPUT: 230V~ 50Hz
GND
ON
SIGN
COMP
(5)
(4)
POWER
OFF
Use only with
a
250V fuse
(2)
(1)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
-. ACTIVE SUBWOOFER Speaker for ELVIS12 SA / ELVIS15 SA
(1) Bi-polar main power switch.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
(4) POWER, blue LED, indicate ON status.
(5) SIGN / COMP, signal/compressor, green/red LED
(6) LEFT signal output on XLR or Jack connector for active satellite, under electronic crossover at 125Hz.
(7) RIGHT on XLR connector for active satellite, under electronic crossover at 125Hz.
(8) VOLUME main power amplifier control.
(9) RIGHT, input signal on XLR connector.
(10) LEFT/MONO, input signal on COMBO connector.
LINK
(6)
LEFT/
MONO
OUT
RIGHT
(7)
VOLUME
(8)
-
+4dBu
LEFT/
MONO
(10)
IN
RIGHT
(9)
(3)
MODEL
SERIAL
GND
AC INPUT: 230V~ 50Hz
ON
SIGN
COMP
(5)
(4)
POWER
OFF
Use only with
a
250V fuse
(2)
(1)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. WIRE CONNECTIONS
-. For Passive Speaker Cabinets
Please use only the power connectors to make connections with other signal source equipment for the passive speaker
cabinets. The power connector has four terminals: 1+, 1-, 2+, 2-.
1+
2+
In our cabinets, only 1+/1- are used to connect the Speaker+/Speaker-, and 2+/2- are not used.
-. For Active Speaker Cabinets
As to these circumstances, audio connections is mostly intended for the signal flow, so, determine the wire configuration
according to your real application system and its connecting facility. Normally, you have the following choices:
Balanced
Tip
Tip
Ring
Ring
SLEEVE RING TIP
TIP RING SLEEVE
Sleeve
Sleeve
1
2
1
2
3
3
Tip
1
2
3
Ring
TIP RING SLEEVE
Sleeve
Unbalanced
Tip
1
2
3
Ring
Sleeve
TIP RING SLEEVE
Tip
1
2
3
Sleeve
TIP SLEEVE
Tip
Tip
TIP SLEEVE
SLEEVE TIP
Sleeve
Sleeve
Tip
Tip
Ring
Ring
TIP RING SLEEVE
SLEEVE RING TIP
Sleeve
Sleeve
1
2
1
2
3
3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. ELVIS TECHNICAL SPECIFICATIONS
ELVIS10
ELVIS12
2-way vented box
180W AES standard
360W Peak
ELVIS15
2-way vented box
250W AES standard
500W Peak
ELVIS12M
2-way vented box
180W AES standard
360W Peak
2-way vented box
120W AES standard
240W Peak
System type
Continuous power
Peak Power Rating
96dB/116.5dB Max
65Hz/20kHz +/-6dB
8Ohm Nominal
Sensitivity (1W, 1m)
Frequency Response
Impedance
97dB/119.5dB Max
60Hz/20kHz +/-6dB
8Ohm Nominal
98dB/122dB Max
55Hz/20kHz +/-6dB
8Ohm Nominal
97dB/119dB Max
75Hz/20kHz +/-6dB
8Ohm Nominal
Crossover Frequency
2700Hz 12dB/oct
2500Hz 12dB/oct
2200Hz 12dB/oct
2500Hz 12dB/oct
Protection
Electronics High Frequencies Protection
Low-Frequency
10"/266mm woofer
12"/318mm woofer
1"Compression Driver
15"/385mm woofer
12"/318mm woofer
1" Compression Driver
High-Frequency
1"Compression Driver
1"Compression Driver
Spherical Wave Guide
Horn Coverage
Custom Horn with Polypropilene Reinforced
80 H 80 V
80 H 80 V
80 H 80 V
80 H 80 V
Connectors(+1/-1)
2xSPK4 Input/Link @+1/-1 connected - +2/-2 not connected
Enclosure
Trapezoidal cabinet in 18mm particle board P.B. -Covered with resistant carpet -Black metal grille protection
580 345 305mm
Dimensions HxWxD
635 405 340mm
40.34lbs/18.30kg
48.28lbs/21.9kg
6.03CFT
700 455 370mm
50.17lbs/22.76kg
58.86lbs/26.7kg
7.35CFT
615 400 345mm
38.93lbs/17.66kg
46.29lbs/21kg
6.10CFT
31.22lbs/14.16kg
37.92lbs/17.2kg
4.58CFT
Net Weight lbs/kg
Gross Weight lbs/kg
Volume
ELVIS12S
vented box
ELVIS15S
System type
vented box
Continuous Power
Peak Power Rating
Sensitivity (1W, 1m)
Frequency Response
Impedance
200W AES standard
400W Peak
300W AES standard
600W Peak
97dB/119dB Max
50Hz/20kHz +/-6dB
4Ohm Nominal
125Hz 6dB/oct
98dB/122dB Max
45Hz/20kHz +/-6dB
4Ohm Nominal
125Hz 6dB/oct
Crossover Frequency
Protection
Low-Frequency
High-Frequency
Spherical Wave Guide
Horn Coverage
Connectors (+1/-1)
Enclosure
12"/318mm woofer
15"/385mm woofer
2xSPK4 @ in/out
2xSPK4 @ in/out
Trapezoidal cabinet in 18mm particle board P.B. -Covered with resistant
carpet -Black metal grille protection
Dimensions HxWxD
495x400x455mm
51.15lbs/23.2kg
57.98lbs/26.3kg
6.15CFT
565x455x525mm
Net Weight lbs/kg
Gross Weight lbs/kg
Volume
65.48lbs/29.7kg
74.52lbs/33.8kg
8.67CFT
ELVIS10A
ELVIS12A
250Watt IHF
ELVIS15A
350Watt IHF
250Watt RMS
ELVIS12MA
250Watt IHF
Output Power IHF
Output Power RMS
Max SPL at 1mt
Input Sensitivity
Input Impedance
Connectors
150Watt IHF
120Watt RMS
180Watt RMS
180Watt RMS
117.5 dB ( IHF Power )
121 dB ( IHF Power )
123 dB ( IHF Power )
121 dB ( IHF Power )
Line 0dB/0.775V/Mic-10 at -45dB
30kOhms Balanced - 15kOhms Unbalanced
Mic on XLR/Line Input on Combo/Line-Mix Output on XLR
Subsonic Filter
Protections
30Hz - 24dB/oct.
30Hz - 24dB/oct.
30Hz - 24dB/oct.
30Hz - 24dB/oct.
Soft - Start, compressor
External Control
Mic Gain - EQ-High-Mid-Low-Volume-Ground Switch
230Volt/115Volt 50 / 60Hz
Power Supply
Net Weight lbs/kg
Gross Weight lbs/kg
Volume
40.12lbs/18.2kg
46.83lbs/21.24kg
4.58CFT
50.95lbs/23.11kg
58.89lbs/26.71kg
6.03CFT
62.83lbs/28.5kg
71.52lbs/32.44kg
7.35CFT
49.54lbs/22.47kg
56.92lbs/25.82kg
6.10CFT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ELVIS12SA
250Watt IHF
ELVIS15SA
350Watt IHF
Output Power IHF
Output Power RMS
Max SPL at 1mt
Input Sensitivity
Input Impedance
Connectors
180Watt RMS
250Watt RMS
121 dB ( IHF Power )
123 dB ( IHF Power )
Line 0dB/0.775V
30kohms-input/600ohms-output
L/Mono-R IN on XLR/L-R OUT on XLR
Electronic Crossover 125Hz at 24dB/oct.
Soft - start, compressor
Subsonic Filter
Protections
External Control
Power Supply
Volume - Stereo/Mono & Ground Swicth
230Volt/115Volt 50/60Hz
60.36lbs/27.38kg
76.68lbs/34.78kg
85.72lbs/38.88kg
8.67CFT
Net Weight lbs/kg
Gross Weight lbs/kg
Volume
67.19lbs/30.48kg
6.15CFT
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SEIKAKU TECHNICAL GROUP LIMITED
No. 1, Lane 17, Sec. 2, Han Shi W. Road, Taichung, 401 Taiwan
All rights reserved to ALTO Mobile. Due to continued development in response to
customer feedback, product features, specifications and/or internal/external design may be
changed without prior notice. No photocopying, translation or reproduction of any part of this user
c
manual is allowed without prior written permission.Copyright 2004 Seikaku Technical Group Limited.
NF01105-1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|