I N S T A L L A T I O N G U I D E
REMOTE CONTROL ANYWHERE!® KIT
-
RCA TT2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTROdUCTION
The Niles RCA-TT2 Remote Control Anywhere! Kit enables you to operate your remote controlled
audio/video equipment from virtually any location. Now you can place your audio/video (A/V)
components out of sight (behind cabinet doors, in the rear of a room, or in a different room) and still
conveniently control your system.
CONTENTS
Check that your RCA-TT2 Remote Control Anywhere! Kit contains the following:
• Connection hub
• Tabletop sensor
• 12VDC power supply
Connection Hub
Tabletop Sensor
MicroFlasher (3)
• MicroFlasher® (3)
• CAT-5 sensor cable (50’) (15.24 meters)
12VDC Power
Supply
CAT-5 Sensor
Cable (50ft)
1
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES ANd BENEFITS – REMOTE CONTROL ANYWHERE! KIT
COMPLETE SYSTEM
Everything needed to assemble a complete IR extender system is included in one box:
ONE INFRAREd SENSOR
Receives/initiates the IR commands and routes them to the Main System Unit
ONE MAIN SYSTEM UNIT
Amplifies and distributes the commands to each infrared MicroFlasher®
IR MICROFLASHER® (THREE)
Transmit the IR commands to the audio/video components
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES ANd BENEFITS – IR SENSOR
HIGH-FIdELITY WIdEBANd dESIGN
Ensures compatibility with virtually any brand of equipment, even those using faster, more difficult
to reproduce IR codes
PATENT PENdING UNIVERSAL NOISE SUPPRESION dESIGN
Enables operation in virtually any IR environment: near plasma and LCD displays, compact fluores-
cent lights, and direct sunlight
EXTENdEd IR RECEIVING RANGE
Enjoy the convenience of 20’ to 35’ of remote control range (6.1 meters to 10.6 meters)
PRINTEd CIRCUIT BOARd
Our printed circuit board uses surface mount technology (SMT) to ensure reliability
COMPACT SIZE
Tabletop design fits almost anywhere; only 2-7/8” wide x 1-1/16” high x 3-1/8” deep
(7.30 cm wide x 2.70 cm high x 2.86 cm deep)
3
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES ANd BENEFITS – MAIN SYSTEM UNIT
UNIVERSAL SYSTEM
Compatible with virtually all brands of audio/video equipment and remote controls
VERSATILE CONNECTIONS
Accommodates one IR MicroSensor® with removable screwless connector plus four flashers
via 3.5 mm jacks
SYSTEM FEEdBACK LEd
Confirms proper operation
3-30V AC/dC STATUS INPUT
Provides system status to connected sensors and keypads
EXPANdABLE
An IRH610 IR Expansion Hub can be used to provide additional inputs
INTEGRATEd MOUNTING WINGS
Both horizontal and vertical installation is supported
POWER SUPPLY
UL listed regulated power supply with universal voltage capability
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES ANd BENEFITS – MICROFLASHER®
MINIATURE ANd dISCRETE
MicroFlasher mounts directly to the IR remote sensor window of your audio/video equipment while
maintaining a clean appearance
INFRAREd BLOCKING COVER
Useful when controlling several identical TVs (or audio/video components) that use the same remote
control and IR commands
TRANSPARENT TO IR COMMANdS
Even though the MicroFlasher covers the IR remote sensor window, you can still directly operate
your equipment using a remote control
EASY INSTALLATION
A strip of self-adhesive tape provides secure mounting
CONNECTING WIRE
A 10’ connecting wire (3 m) is fitted with a 3.5 mm mono mini-plug to provide a secure connection
to the MSU
5
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION CONSIdERATIONS
WARNING – TO pREVENT pOSSIbLE INjURy, THE FOLLOWING bASIC SAFETy pRECAUTIONS SHOULD bE
ObSERVED IN THE INSTALLATION AND USE OF yOUR RCA-TT2 REMOTE CONTROL ANyWHERE! KIT.
1. Read through the entire manual – Before attempting any installation, read this manual
thoroughly and keep it for future reference.
2. Avoid contact with all high voltage electrical wiring and equipment.
3. Keep away from water and moisture – Never use or install electronic products near water, ie.,
near a bathtub, sink, washing machine, in a wet basement, near a swimming pool, or anywhere
else the product may be exposed to water or moisture.
4. Power supply cord protection – Do not run the power cord where it may be subject to wear or
abuse. Do not allow anything to rest on or roll over the power cord which may damage it.
6. Lightning – It is suggested that you remove the power supply from the wall if your system will
not be used for long periods of time. Power surges due to lightning strikes may damage your
equipment.
7. Check your local building and electrical codes – There may be specific requirements regarding
running low voltage in your area.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TOOLS REQUIREd
• Pencil
• Drywall saw
• Standard screwdriver
• Phillips screwdriver
• Wire strippers
• Drill (and assorted bits)
GETTING STARTEd
While the Remote Control Anywhere! Kit is compatible with most brands of audio/video components,
there are a few exceptions. you should perform a temporary hook-up to test for compatibility
before you conceal wire or permanently mount any parts.
Steps One through Five describe how to perform a quick and easy check for compatibility. Once you
have determined that all of your remote controlled A/V components are compatible, proceed
with the rest of the installation.
7
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 1 – PLACING THE CONNECTION HUB
place the Connection Hub so that the MicroFlasher wires will reach the components.
Never place the connection hub closer than 1’ away from a television set (Figure 1).
Figure 1 Connection Hub Placement
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 2 – CONNECTING THE SENSOR CABLE TO THE
CONNECTION HUB
Select four conductors of the supplied CAT-5 wire and strip approximately 1/4" of insulation from
the wire. Insert each wire into the appropriate hole on the removable connector plug (Figure 2),
and snap the locking tab down. To help you, the connector plug is keyed. Insert the smooth side of
the connector plug into the smooth side of the socket. Don’t force the scalloped side of the con-
nector plug into the smooth side of the socket.
To Niles IR Flasher
To 12VDC power Supply
Plugged into an switched AC
To unswitched
AC Outlet
Outlet. Typically found in back of
a receiver.
MSU140
TS120 Tabletop Sensor
MSU140 Sensor Connection
Figure 2: MSU140 Installation
9
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 3 – CONNECTING THE SENSOR CABLE TO THE
TABLETOP SENSOR
Pull out the removable connector from the bottom of the tabletop sensor. Insert each wire into the
appropriate hole on the removable connector plug (Figure 3), and snap the locking tab down.
To help you, the connector plug is keyed. Insert the smooth side of the connector plug into the
smooth side of the socket. Don’t force the scalloped side of the connector plug into the smooth
side of the socket.
Figure 3: Removable Connector Plug
TECH TIP: Wire size is expressed by it’s AWG (American Wire Gauge) number. The lower
the AWG number, the larger the wire, i.e., 20 AWG wire is physically larger than 22 AWG.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 4 – CONNECTING THE 12VdC POWER SUPPLY ANd EACH
MICROFLASHER®
plug each MicroFlasher into any of the sockets labeled FLASHER OUTpUTS on the connection hub
(Figure 5). plug the connector on the supplied 12VDC power supply into the socket labeled pOWER
on the connection hub and then plug the wall adapter into a live electrical outlet. The power LED
should light. If the LED does not light, confirm that the outlet you used is live by plugging in a lamp.
NOTE: MAKE ALL FINAL CONNECTIONS TO THE MSU bEFORE CONNECTING THE pOWER SUppLy. THIS
WILL AVOID pOTENTIAL DAMAGE TO COMpONENTS.
Figure 4: Installing Sensor Connector
Figure 5: Connection Ports
11
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 5 – MOUNTING A MICROFLASHER TO A/V COMPONENTS
Make sure all of your remote controls have batteries and that they are able to operate the A/V com-
ponents. Locate a place for the remote control that is within arm’s length of the A/V components,
yet cannot directly control them. Place the tabletop sensor no closer than two feet in front of the
remote control (Figure 6).
Hold the MicroFlasher four inches in front of the remote sensor window on the A/V component’s
front panel. Press buttons on the remote control while watching the front panel of the A/V
component. When the component responds repeatedly to the commands, peel off the protective
backing on the MicroFlasher and place the MicroFlasher in that location.
If the A/V component’s remote sensor is not clearly
marked, slowly move the MicroFlasher over the win-
dow of the A/V component while pushing buttons on
Tabletop Sensor
the remote control until you get a response (Figure 7).
Repeat this procedure for each A/V component you
wish to control.
When the A/V component responds repeatedly, peel off
the protective backing on the MicroFlasher and place
the MicroFlasher in that location.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 6 – MOUNTING THE CONNECTION HUB
Make sure that your system tested OK before proceeding.
Once you have decided on the ideal location for the connection
hub, unplug the 12VDC power supply from the electrical outlet
and disconnect the sensor and the MicroFlasher cables from the
connection hub (Figure 8). Also remove the connector from the
tabletop sensor (Figure 9).
The connection hub can be either mounted on a wall using screws
or placed on a shelf using the included adhesive feet (Figure 10).
Figure 7: Locating IR Sensor
Figure 8: Removing Cables
Figure 9: Removing Sensor Connector
13
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
MSU140 base
Self-Adhesive
Rubber Feet
Figure 10A: Wall-mount placement
Figure 10B: Tabletop placement
Affix the enclosed self-adhesive
rubber feet to the base of the MSU140
Use sheetrock screws
STEP 7 – RUNNING THE SENSOR CABLE
Conceal the sensor cable between the tabletop sensor and the connection hub. For specific
information refer to “Running Sensor Cable in New
Construction” or “Concealing Sensor Cable in Existing
Walls.” If you need to cut and restrip the wire, make sure
that only 1/4” of wire is exposed. Exposing too much
wire could create “shorts” within the system.
IMpORTANT: IF yOU HAVE DOUbTS AbOUT WHETHER yOU
ARE CApAbLE OF INSTALLING A NILES RCA-TT2 REMOTE
CONTROL ANyWHERE! KIT IN yOUR WALLS, CONSULT A NILES
DEALER OR pROFESSIONAL INSTALLER. THEy HAVE SpECIAL
TOOLS, TECHNIqUES, AND ExpERIENCE TO MAKE THE
IMpOSSIbLE pOSSIbLE. THE INSTALLER CAN pROVIDE yOU
WITH AN ESTIMATE bEFORE ANy WORK IS DONE.
Figure 11: Connecting Power Supply and Flashers
14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 8 – MOUNTING LOCATION
The TS120 is designed to be mounted over or under almost any flat, horizontal surface. Suggested
locations include:
• On top of the television set
• On a shelf in an entertainment center
• Under a shelf in an entertainment center
Hidden Entertainment Equipment
Figure 12: Typical Mounting Location
TS120
15
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
STEP 9 – RECONNECTING THE CONNECTION HUB
Reconnect the sensor plug, flashers and power supply as outlined in steps 2, 3 and 4 (Figure 11).
That’s it! Now you are ready to control your audio/video equipment from the room you chose.
NOTE: MAKE SURE THAT THE STRIppED ENDS OF THE WIRE DO NOT COME IN CONTACT WITH ONE
ANOTHER OR ANy SURFACE OTHER THAN THE CONNECTOR.
NORMAL OPERATION
To control your audio/video components, simply aim your remote control at the tabletop sensor.
If you are within range (and your remote control’s batteries are fresh), the LED on the sensor will
flash a bright blue color each time you press a button on the remote (Figure 13). If you are using
a remote control with macro capabilities (a single press of a button issues a string of commands),
allow sufficient time for all of the commands to execute.
Figure 13: System Operation
16
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
OPTIONAL ACCESSORIES
AddITIONAL FLASHERS
Although the RCA-TT2 Remote Control Anywhere! Kit includes three flashers, the connection hub
can accommodate up to four. Order model MF1 (Stock# FG01019) from your authorized Niles dealer
for each additional A/V component you wish to control.
STATUS FEEdBACK WALL AdAPTER
The tabletop sensor features a status feedback LED that glows green whenever your system is on.
This is a very useful feature when operating your equipment from a remote location. For this feature
to work, your system receiver (or preamp) must have a switched AC outlet and you must purchase
the optional Status Feedback 12VDC Wall Adapter (FG01035). The Status Feedback wall adapter
is plugged into the switched AC outlet of your receiver. The 12VDC output plug is inserted into the
connection hub’s Status Input (Figure 14).
AddITIONAL SENSORS
The RCA-TT2 Remote Control Anywhere! Kit includes one tabletop sensor. Niles also makes a
variety of sensors for virtually any application. See your Niles dealer for more information or visit
17
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
Optional Niles Universal
12VDC power Supply
(FG01035)
Figure 14: Connecting the
Status Adapter
RUNNING SENSOR CABLE IN NEW CONSTRUCTION
Scheduling and Preparation
Plan to schedule the sensor wiring after the electrical wiring is finished. That way you can avoid cable
routes which could potentially induce interference over the sensor cable. The basic rules are:
• Never run the sensor cable through the same hole as an electrical cable.
• Never run the sensor cable into the same J-box as electrical cable.
• Avoid running the sensor cable beside the electrical cable. Keep it at least 3 or 4 feet distant
from any electrical power cable.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
As side-by-side wiring is unavoidable in particular spots in every house, just move the sensor cable
route away as soon as possible. If construction forces a side by side run for more than ten feet,
install metal conduit or shielded sensor cable. Low-voltage cables such as doorbells, intercoms,
telephone, speaker, security, or television cannot cause interference on your sensor cables, so you
can safely run all of them at the same time, through the same holes, side-by-side.
SAFETY FIRST!
Wear gloves, safety goggles and head protection when drilling. Avoid nails, they ruin bits and they
can cause injury. Pay particular attention when using “hole-hogs” and other powerful electric drills;
the torque of the drill when suddenly stopped by a nail can break a strong person’s wrist.
dRILLING
Use a bit that is large enough for the cables you plan to run. An auger bit is the preferred bit for
rough-in wiring. It will actually pull itself through the wood, so that the drill motor, not you, does
most of the work. Always drill the holes in the center of the stud. If you have to notch the stud or
drill the hole closer than one inch from the edge of the stud, protect the cable with a nail plate.
When drilling holes in ceiling joists, drill in the center of the joists and try to locate the hole near
the end of the joist. DO NOT drill through a “glulam” or any load bearing beam without the
direction of your contractor.
Try to line the holes up perfectly, because it makes pulling the cable much easier. A good technique
is to snap a chalk line across the face of the studs or against the bottom of the ceiling joists. Then
work backward so that you can always see the holes you have already drilled. Paying careful
attention to this will save you a lot of time later!
19
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
PULLING THE CABLE
Whenever you run the cable farther than 4-1/2 feet from a hole in a stud or joist (open attic space,
going up walls, etc.), fasten the cable to the joists or studs using cable clamps or appropriately
sized cable staples. The cable should not have large sags in it, nor should it be too tight. Try to
protect the cable from being stepped on in attics or other unfinished crawl spaces. There are guard
strips, raceways and conduits which can be used to protect the cable. Consult the local building
code for special requirements in your area.
CONCEALING SENSOR CABLE IN EXISTING WALLS
This is actually a fairly simple task if you restrict your choice of the tabletop sensor location and
cable routes to the interior walls or ceilings of your home. Interior walls in almost all North American
residences are hollow, so that it is easy to route new sensor cable around the house. What you see
when you look at the painted wall board, plaster, or paneling is only the skin of the wall. Behind
the skin is the skeleton; two-by-four wood or metal “studs” running vertically from the floor to the
ceiling in walls and 2 x 6 or larger “joists” running horizontally in the ceilings and floors. In between
the studs and the joists is the space for the wiring and plumbing of your home.
Exterior walls are different. They must insulate the house from the heat and cold outside, so they
are stuffed with insulation. The national building code requires that the hollow wall space in exterior
walls be broken by a horizontal stud placed between the vertical studs. This “fire blocking” makes
it very difficult to retrofit long lengths of cable. In some areas of the country the exterior walls are
constructed of solid masonry, and have no hollow space for cables.
Start by examining all the possible routes you might take to run the sensor cable from the sensor
location Installation to the A/V components to be controlled. Use a stud sensor or other device to
20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (continued)
locate the internal structure of the wall. you want to avoid all studs or joists. A typical route would be
from the sensor location up the inside of the wall to a new hole drilled into the top “plate”
(horizontal 2 x 4 at the top of the inside of the wall), into the attic crawl space, then down another
plate to the wall behind the stereo system itself. The other very common route is through the bottom
plate of the wall into an unfinished basement or crawl space.
Identify where all of your electrical, phone, and TV wiring is likely to be and plan to route around
it all. you can accidentally induce interference on your sensor cable right beside electrical cable
for more than a few feet. Try to keep sensor cable running parallel to power cables at least 3 feet
away. To find exactly where an electrical cable is routed, try inspecting the inside of the wall by
turning off the breaker for a particular power outlet or switch, removing the cover plate and switch
or receptacle, and shining a penlight into the wall. If you have access to an attic or basement space,
you can see which part of the wall space is free of obstructions (Figure 15).
Figure 15: Unobstructed space for sensor cable
21
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION continued
When you don’t have access above or below the wall, try to estimate the existing cable and pipe
locations from the positions of electrical outlets and plumbing fixtures on both sides of the wall.
Also, take a look at the outside of your house, sometimes a conduit, vent or drain pipe will be visible
and will offer useful information. Choose the route with the fewest potential obstacles. If your house
is built on a slab or you are wiring between two finished floors, look for baseboards which could
be removed and replaced with the cable behind them. Doorjambs can be removed and often have
enough space for sensor cable all the way around the door (Figure 16).
Sometimes, an under-the-carpet run is possible. As a last resort, heating and air conditioning vents
can be used as cable raceways for plenum rated cable (check your local building codes, some
municipalities require a conduit)
When you are dealing with the unknown because of the structure of your home, or with difficult
materials to patch the wall, such as plaster, lath and plaster, faux finishes, wallpaper etc., be
patient. A careful study of the potential problems before you start the job will pay off later.
Figure 16: Routing Wire Around a Door
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
MSU140
Mounting
Tabletop
IR System Compatible with virtually all brands
of remotes using carrier frequencies between
25kHz and 90kHz
Wiring Requirements
Individual “home-runs” of CAT-5 cable
Unit Dimensions
Wiring Requirements Individual home-runs of
2-7/8" wide x 1-1/16" high x 3-1/8" deep
CAT-5 cable from each sensor/keypad
(7.30 cm wide x 2.70 cm high x 2.86 cm deep)
Unit Dimensions 4-3/4" wide x 1-1/4" high x
2" deep (12.07 cm wide x 3.18 cm high x 5.08
cm deep)
MF1
IR System Compatible with virtually all brands
of remotes using carrier frequencies between
25kHz and 90kHz
Power Requirements
12 vDC power supply (included).
TS120
IR Transmitting Range Up to 4' (1.22 meters)
(Typically mounts to the IR remote sensor
window of an audio/video component)
IR System Compatible with virtually all brands
of remotes using carrier frequencies between
25kHz and 90kHz
IR Transmitting Angle
Transmits in a “pinpoint” transmission pattern
(the off-axis power drops off very rapidly)
IR Receiving Range 20' to 35' (6.10 meters to
10.67 meters) depending upon the strength of
the remote control
Unit Dimensions
IR Receiving Angle 30° off-axis (horizontal
and vertical) at 25' (7.62 meters)
5/16" Wide x 3/16" High x 1/2" Long
.79 cm Wide x .48 cm High x 1.27 cm Long
23
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITEd WARRANTY
Niles Audio Corporation (“NILES”) warrants its active products (those requiring AC or battery power) to the original purchaser to be free
of manufacturing defects in material and workmanship for a period of two years from date of purchase.
This Warranty is subject to the following additional conditions and limitations.The Warranty is void and inapplicable if NILES deems
that the product has been used or handled other than in accordance with the instructions provided by the manufacturer, including
but not limited to damage caused by accident, mishandling, improper installation, abuse, negligence, or normal wear and tear, or
any defect caused by repair to the product by anyone other than NILES or an authorized NILES dealer.
To obtain warranty service, take the unit to the nearest authorized NILES dealer, who will test the product and if necessary, forward
it to NILES for service. If there are no authorized NILES dealers in your area, you must write to NILES and include your name,
model and serial number of your unit, along with a brief description of the problem. A factory Return Authorization Number will
be sent to you. DO NOT RETURN ANy UNIT WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIppING INSTRUCTIONS
FROM NILES.
If the above conditions are met, the purchaser’s sole remedy shall be to return the product to NILES, in which case NILES will
repair or replace, at its sole option, the defective product without charge for parts or labor. NILES will return a unit repaired or
replaced under warranty by shipping same by its usual shipping method from the factory (only) at its expense within the United
States of America. THERE ARE NO OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION, EITHER EXPRESS OR IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PRODUCT.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER/
PURCHASER. NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE
EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the name of your nearest authorized NILES dealer, contact:
NILES AUDIO CORpORATION, p.O. bOx 160818, Miami, Florida 33116.
Please fill in your product information and retain for your records.
RCA-TT2
Model ____________________________ Serial No. _________________________ purchase Date ____________
24
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY REGISTRATION CARd
RCA-TT2
Model purchased__________________________________ Serial Number __________________________
Date purchased (month/day/year)______________________ Dealer Name and Location _________________
❍
❍
❍
❍
❍
Dr.
Name ____________________________________ Address _____________________________________
City_______________________________State__________Zip ___________ Tel ( ) ____________
Miss
Mr.
Mrs.
Ms.
❍
❍
❍
❍
❍
❍
Age:
New Age
R&B
Popular
Rock
Myself
Are there products/capabilities
❍
Under 25
that you would like to see introduced?
________________________
________________________
________________________
________________________
Which factor(s) influenced the purchase
of your Niles product? (Please check
all that apply)
❍
❍
❍
❍
25-34
Other ________________
35-44
How did you hear about Niles?
45-54
55 & over
❍
❍
Architect/Developer
Custom Installer
❍
❍
❍
❍
❍
❍
❍
Ease of Use
Price/Value
Income:
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Direct Mail
Product Features
❍
Under $24,999
Friend/Family
In-Store Display
Interior Designer
Magazine Ad
Mail-Order Catalog
Newspaper Ad
Product Brochure
Product Review
Retail Salesperson
E-Tailer
Quality/Durability
❍
❍
❍
❍
❍
$25,000-$44,999
$45,000-$74,999
$75,000-$99,999
$100,000-$129,999
Over $130,000
Reputation
Style/Appearance
Warranty
Do you . . . ?
❍
Own a House. If yes,
Occupation:
how many square feet?
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Arts/Entertainment
Business Owner
______________________
Engineer
Finance/Accounting
What magazines do you read?
1. _____________________
2. _____________________
3. _____________________
Who will install the product?
❍
Own a Town House/
General Office
Condominium/Co-op
Management
❍
❍
Rent an Apartment
Professional
Sales/Marketing
Student
Rent a House
Are you interested in receiving
Tradesperson
literature on other Niles products?
❍
❍
Yes
No
Musical tastes: (Please check
all that apply)
❍
❍
❍
Custom Installer
❍
❍
❍
❍
Alternative
Country
Classical
Jazz
Electrician
Friend
25
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Bl e n d i n g Hi g H Fi d e l i t y An d Ar c H i t e c t u r e
N i l e s A u d i o C o r p o r a t i o n
1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6
3 0 5 - 2 3 8 - 4 3 7 3
•
1 - 8 0 0 - B u y - H i f i w w w . n i l e s a u d i o . c o m
©2009 Niles Audio Corporation. All rights reserved. Niles, the Niles logos, MicroSensor, MicroFlasher, Remote Control
Anywhere! and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation.
All other trademarks are the property of their respective owners. DS00685A
Download from Www.Somanuals.com. All Manuals Search And Download.
|