M O
D
E L
SVL-6
SVL-6
SPEAKER SELECTION/VOLUME CONTROL SYSTEM
NILES
®
I N S T A L L A T I O N & O P E R A T I O N G U I D E
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Feat ures and Benefit s
The SVL-6 offers a number of improvements over other
speaker selector/volume controllers:
● The SVL-6 uses 12 position volume controls which are
superior to 10 position designs. You get a broader range of
adjustment —there are 10 steps of attenuation instead of
8. Steps 11-6 attenuate -3 dB per step; steps 5-2 are 6 dB
per step. Step 12 is "full-on" and step 1 is "full-off".
TECH
SUPPORT
HOTLINE
If you have
questions regarding
the operation of the
Niles SVL-6, contact
your local Niles
● Greater dynamic range —you get 42 dB of total attenua-
tion instead of the usual 20 or 30 dB.
● POP-FREE switching between all steps.
dealer or Niles
Customer Service at
1-800-289-4434.
● Pre-printed Room Labels are included for easy identifica-
tion of speaker ON/OFF buttons.
● Rear-panel switch for constant or selectable impedance
protection.
● Isolated left and right channel ground returns make the
SVL-6 compatible with all types of amplifiers.
● Self-cleaning, silver-plated switch contacts assure many
years of trouble free use.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
● Printed circuit board design assures high reliability.
● Two-piece removable connectors greatly simplify installa-
tion and hookup. All wiring can be attached directly to the
connectors before installing them in the SVL-6.
● Removable connectors accommodate up to 14 gauge wire
or "pins", making the SVL-6 compatible with most "high-
definition" speaker cables.
● 100% tested, electronically and acoustically, for frequency
response, distortion and power handling.
● Standard 17" width allows the SVL-6 to stack neatly with
other standard size components.
● May be used with 4, 6, or 8-ohm speaker systems.
● Ideal for both home and commercial sound installations.
● Only an 1/8" standard screwdriver and wire stripper are
required for installation.
● Power handling: 100 watts/channel continuous music
power.
● Frequency response: 20 Hz to 20 kHz +/-1.2 dB.
● Ten year parts and labor warranty.
● Proudly made in the USA.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion Considerat ions
SVL-6 Power Handling
TOOLS
REQUIRED
The SVL-6 is designed for use with a receiver or amplifier hav-
ing a maximum power output of 100 watts per channel at 8
ohms. Damage caused by the use of a higher-power receiver
or amplifier will void the warranty. Consult your Niles dealer,
or receiver/amplifier manufacturer, if you are uncertain about
the power rating of your receiver or amplifier.
• 1/8" Standard
Slotted Screwdriver
• Wire Stripper
IMPORTANT: DO NOT USE THE SVL-6 W ITH AMPS OR
RECEIVERS RATED AT MORE THAN 10 0 W ATTS PER
CHANNEL RMS AT 8 OHMS.
IMPORTANT
DO NOT use the
SVL-6 with amps
or receivers rated
at more than 100
watts per channel
RMS at 8 ohms.
Am plifier Im pedance Load
As m ore pairs of speakers are parallel connected to a
receiver or am p lifier, th e overall system im p ed an ce
becom es lower. For exam ple, if two pairs of 8-ohm
speakers are connected in parallel, the impedance will be
4 ohms; two pairs of 4-ohm speakers in parallel become 2
ohms, and so on.
Most receivers or amplifiers are not rated for use below a 4
ohm load. Most manufacturers do not recommend connect-
ing more than two pairs of speakers without using some
form of impedance correction.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
The SVL-6 includes impedance correction circuitry which
protects your receiver or amplifier from low impedance
loads. The circuitry assures that your receiver or amplifier will
see a safe operating load, even when all six speaker pairs are
playing at the same time.
The actual impedance load the SVL-6 presents to your receiv-
er or amplifier will vary, depending on how many speaker
pairs are playing, and the impedance rating of each speaker.
If you have six pairs of 8-ohm speakers playing, the SVL-6 will
present a 4.3 ohm impedance load to your receiver/amplifier.
With six pairs of 4-ohm speakers playing, the load drops to
slightly under 4 ohms.
If you intend to use the SVL-6 with more than two pairs of
4-ohm speakers, it is recommended that you verify that the
receiver or amplifier is capable of driving a 4-ohm load.
Consult your Niles dealer, or the receiver/amplifier manu-
facturer, if you are uncertain about the capabilities of the
receiver/amplifier.
Type of Speaker Wire
For most applications, we recommend you use 16 or 18
gauge stranded copper speaker wire for the SVL-4 connec-
tions. For wiring runs longer than 80 feet, 14 gauge wire is
recommended. Using speaker wire larger than 14 gauge for
the SVL-6 connections is not recommended —the wire may
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
not fit into the connectors. Never use solid-core, aluminum,
or "Romex" type wire with the SVL-6. When running speaker
wires inside walls, most states and municipalities in the U.S.
specify that you must use a special type of speaker wire.
Usually, the requirement is that the wire that has a specific
"CL" fire rating, such as "CL-2" or "CL-3". Consult your Niles
dealer, building contractor, or local building and inspection
department if unsure about which type of wire is best for
your application.
"TECH TIP"
Wire size is
expressed by it's
AWG (American
Wire Gauge)
number. The lower
the AWG number,
the larger the wire,
i.e., 12 AWG wire is
physically larger
than 14 AWG.
Avoiding Int erference
Speaker wires can act as an antenna for electrical noise.
Locating speaker wires too close to a light dimmer or switch
may cause a "buzzing" or "popping" sound to be heard
though the speakers. If you must locate the SVL-6 wiring near
electrical devices, route the speaker wires several feet away
from the electrical wiring.
Using t he SVL-6 wit h Tube-Type Am plifiers
Virtually all tube amplifiers must have a load connected at all
times. If the amplifier to be connected to the SVL-6 is a tube
amplifier, be sure to always have at least one pair of speakers
switched on at all times. An alternative is to permanently
connect a 150 ohm, 5 watt resistor across the tube amplifier's
output in parallel with the SVL-6. See (Fig ure 1) on next
page for hookup diagram.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Tube Amplifier
Figure 1
Using a
Tube Amplifier
150
150
Niles SVL-6
AMPLIFIER
L- R-
SPEAKER
6
SPEAKER
5
SPEAKER
4
SPEAKER
3
SPEAKER
2
SPEAKER
1
L+
R+
L+
L-
R-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
L-
R-
R+
L+
L
-
R
-
R+
L+
L-
R-
R+
ON OFF
N
I
L
E
S
CONSTANT
PROTECTION
Niles Audio
Corporation, Inc.
Miami, Florida USA
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
12 position volume control
provides greater attenuation
than conventional 10 position
designs.
Recessed
areas for
custom room
labels.
SVL-6 SPEAKER SELECTION/ VOLUME CONTROL SYSTEM
PROTECTION
Attractive
low-profile
design.
N
I
L
E
S
1
2
3
4
5
6
Simple
push-button
operation.
Connect up to six pairs
of speakers.
Protection switch safeguards your
receiver or amplifier even with all
6 pairs of speakers playing.
AMPLIFIER
L- R-
SPEAKER
6
SPEAKER
5
SPEAKER
4
SPEAKER
L-
3
SPEAKER
2
SPEAKER
1
L+
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
R-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
ON OFF
N
I
L
E
S
CONSTANT
PROTECTION
Niles Audio
Corporation, Inc.
Miami, Florida USA
Constant
Two-piece
removable
connectors.
Impedance
Protection
Switch
8
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion
1. Select a convenient location for the SVL-6.
2. Run all the necessary wiring to the SVL-6. Label the wires
for future reference. See (Figure 2).
Receiver
Figure 2
Wiring Diagram
Niles SVL-6
Speaker
Pair 6
Speaker
Pair 5
Speaker
Pair 4
Speaker
Pair 3
Speaker
Pair 2
Speaker
Pair 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
3. Make the connections to the SVL-6. The amplifier/speaker
connectors on the SVL-6 are removable. If you wish, you may
remove the SVL-6's connectors to facilitate installation [see
(Fig ure 3)]. Strip 3/8" of insulation from the end of each
wire. Tightly twist the end of each wire until there are no
frayed ends. Insert each wire into the appropriate hole on the
connector terminals. Be certain that proper phasing is
observed —connect the positive terminals on the SVL-6 to
the positive terminals on the amplifier and speakers and the
negative terminals on the SVL-6 to the negative terminals on
the amplifier and speakers. Re-install the connectors if they
were removed. See (Figure 4).
4. Locate the pre-printed Room Labels. Affix the appropriate
label to the recessed area over each ON/OFF selector button.
Figure 4
Installing the Connectors
Figure 3
Removing the Connectors
1
0
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Op erat ion
There are two ways to use the SVL-6. You may play and
adjust the volume of one pair of speakers at a time, or play
multiple pairs simultaneously.
"TECH TIP"
If your amplifier or
receiver has "A"
and "B" speaker-
pair outputs,
If you intend to play more than one pair of speakers at the
same time, you will need to become familiar with the oper-
ation of the SVL-6's PROTECTION button.
connect the SVL-6
to the "A" outputs.
Do not connect
anything to "B".
This will prevent
the amplifier or
receiver from
Playin g On e Pair of Sp eakers At a Tim e
1. Make sure the amplifier or receiver power is OFF and set
the volume to minimum.
2. Set the SVL-6 volume control for the speaker pair you
wish to play to maximum (fully clockwise).
driving an
3. Locate the ON/OFF button on the SVL-6 which corre-
sponds to the speaker pair you wish to play. Set it to the
ON position.
unusually low
impedance load.
4. Turn on the amplifier or receiver and select as source,
such as the tuner or CD player.
5. Slowly turn up the amplifier or receiver volume and set it
to a comfortable (not maximum) listening level. Be careful
not to overdrive or "clip" your am plifier. If the sound
becomes muddy or distorted, you have reached the limit of
your amplifier's volume capability and should quickly reduce
the volume to avoid damaging your speakers.
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
6. Using the appropriate volume control on the front of
the SVL-6, adjust the volume of the speakers to the desired
listening level.
7. You can turn off the speakers by turning the appropri-
ate volume control on the SVL-6 fully counter-clockwise
or by pressing the ON/OFF button.
"TECH TIP"
You will need to
activate the SVL-6's
PROTECTION button
whenever the
overall system
impedance might
fall below
P la yin g
Tw o
o r
M o r e
Sp e a k e r
P a ir s
Sim ult an eously
1. Make sure the amplifier or receiver power is OFF and
set the volume to minimum.
4 ohms.
2. On the right side of the SVL-6's front panel is a button
labeled PROTECTION. This button activates the SVL-6's
impedance correction circuitry. The circuitry assures that
your receiver or amplifier will see a safe operating load
when playing multiple speaker pairs simultaneously. Since
most receivers and amplifiers are not rated for use below a
4 ohm load, you will need to activate the PROTECTION
button whenever the overall system impedance might fall
below 4 ohms. Use the following chart as a guide for set-
ting the PROTECTION button.
WHEN PLAYING THE FOLLOWING :
1 or 2 pair of 8-ohm speakers
OFF
ON
OFF
ON
ON
3 or more pairs of 8-ohm speakers
1 pair of 4-ohm speakers
2 or more pairs of 4-ohm speakers
Any combination of 4 and 8 ohm speakers
Set t he PROTECTION but t on t o t he correct posit ion using t he chart shown above.
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
3. Set the SVL-6 volume controls which correspond to the
speaker pairs you wish to play to maximum.
4. Locate the appropriate ON/OFF buttons on the SVL-6. Set
them to the ON position.
5. Turn on the amplifier or receiver and select as source, such
as the tuner or CD player.
6. Slowly turn up the amplifier or receiver volume and set it to
a comfortable (not maximum) listening level. Be careful not to
overdrive or "clip" your amplifier. If the sound becomes
muddy or distorted, you have reached the limit of your ampli-
fier's volume capability and should quickly reduce the volume
to avoid damaging your speakers.
7. Using the appropriate volume controls on the front of the
SVL-6, adjust the volume of the speakers to the desired listen-
ing level.
8. You can turn off the speakers by turning the corresponding
volume controls on the SVL-6 fully counter-clockwise, or by
pressing the appropriate ON/OFF button. Refer to the
Protection chart for the correct setting of the PROTECTION
button.
1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
SPECIFICATIONS
Const ant Prot ect ion Swit ch
Audio Power
The SVL-6 is equipped with a manual override for the protec-
tion circuit that enables you to defeat the front panel protec-
tion switch and maintain constant impedance protection. This
will safeguard your amplifier from being overdriven due to
accidental or improper use by anyone unfamiliar with the
equipment.
Handling
100 watts/channel
continuous music power
Frequency Response
+/- 1.2 dB from 20 Hz to
20 kHz
Mount ing
Table-Top component
To engage this override, move the rear panel "CONSTANT
PROTECTION" switch to the "ON" position. Constant imped-
ance protection will be maintained until the switch is turned
to "OFF".
Wiring Requirem ent s
Individual runs of
2-conductor speaker
wire. Connectors
Balancing Speaker Volum e
accommodate wire sizes
14-22 gauge (16 gauge
recommended)
The volume control on your receiver or amplifier serves as the
"master" volume for all speaker pairs connected.
Overall Dim ensions
17" wide x 2" high x
9-1/4" deep
The volume level of the speakers may vary from room to
room. This is caused by several factors. Two lesser factors are
the size of the speaker and its efficiency. The largest factor is
the physical size of the room.
Weight
8 3/4 lbs.
The SVL-6's volume controls allow you to adjust the volume
of each speaker pair individually. You can leave the amplifier
or receiver volume set at one position and use the SVL-6 vol-
ume controls exclusively.
1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
NILES ®
®
Niles Audio
Corporation
www.nilesaudio.com
© 1999 Niles Audio Corporation. All rights reserved. Because Niles constantly strives to improve the
quality of its products, Niles reserves the right to change product specifications without notice. Niles
and the Niles logo are registered trademarks of Niles Audio Corporation. Printed in USA 4/96
DS00096A
12331 S.W. 130 Street
Miami, Florida 33186
Tel: (305) 238-4373
Fax: (305) 238-0185
Download from Www.Somanuals.com. All Manuals Search And Download.
|