T E C H N I C A L D A T A S H E E T
800
SW
S U B W O O F E R
®
SW SUBWOOFER
— Designed for low frequency enhancement.
SW-800 In-wall
Enclosure
SW-800 Subwoofer
INTRODUCTION
INTRODUCTION
SW-800 WOOFER
SPECIFICATIONS
The SW-800/SA-100/SW-800 Enclosure,
together comprise an in-wall powered
subwoofer system. This system is ideal
anywhere additional bass response is
desired, but bulky traditional floor stand-
ing subwoofer enclosures just won't
work. Because of it’s modular design the
system can be configured for the exact
requirements of your application.
FREQUENCY
RESPONSE
35 Hz to 150Hz +/- 3 dB
RECOMMENDED
AMPLIFIER POWER
10 to 150 watts
SA-100 Subwoofer Amplifier
LEVEL
SENSITIVITY
POWER
BYPASS
PHASE
NORMAL
ACTIVE
PROTECT
BYPASS
REVERSE
88 dB 2.83V @ 1 meter.
SA-100
FRONT
SPEAKER LEVEL
INPUT
FULL RANGE
OUTPUT
SUB WOOFER
OUTPUT
RAILS
MAIN C.B.
3.0 AMP
3.0 AMP
FULL
RANGE
OUT
HI
PASS
OUT
MAIN
IN
SUB
OUT
AMP
IN
IMPEDANCE
GAIN
SENS
6 Ohm nominal
REAR
HEIGHT X WIDTH
(With frame)
FFEEAATTUURREESS AANNDD BBEENNEEFFIITTSS
14-1/4" H x 10- 3/16" W
the cone. In this way, an SW-800
delivers exceptionally deep and
detailed bass at realistic sound
pressure levels, without the
mechanically induced limiting
and distortion of typical designs.
Component System
Design
Weather-Proof
Construction
The subwoofer, the frame and
the baffle are all weather-proof.
The MicroPerf™ aluminum grille
is rust proof and the mounting
screws are all stainless steel.
HOLE CUTOUT
A system can consist of up to four
SW-800 in-wall subwoofers,
each with SW-800 in wall enclo-
sures, and one SA-100 sub-
woofer amplifier. Vary the num-
ber of SW-800’s to the size of the
room. For example, in a large
Home Theater you would place
three or four SW-800’s and one
amplifier. In a small room like a
den you would place one SW-
800, controlled by one SA-100
amplifier.
13-1/8" H x 9-1/8" W
DEPTH BEHIND WALL
(Assumes 1/2” drywall )
Without In-Wall
Enclosure
X-Matrix™ Reinforced
Baffle
Three Stage Installation
System Prevents Theft and
Simplifies Painting
The X-Matrix baffle design uses
specially molded ribs to add rigid-
ity to the baffle. Rigidity reduces
resonance and coloration, result-
ing in more detail and more real-
ism at high volume levels.
SW-800 3-1/8"
You install only the parts you
need for a particular stage of
construction. When the framing
and wiring are finished, you
install the SW-800 in-wall
enclosure and bracket. After the
drywall is up, but before the
painter begins to paint, you
install the frame and provide the
rustproof aluminum grilles to
the painter so that they can be
painted to match the surround-
ings. Only when construction is
completely finished do you put
the valuable SW-800 subwoofer
in the wall.
CONNECTIONS
Accommodates up to
12 gauge wire
Absolutely Flush to the
Wall Appearance
Mica-Filled Polypropylene
Woofer
The unique mounting system of
the SW loudspeakers powerfully
clamps the frame to the bracket,
sandwiching the wall material
between them. Because the
clamping action is totally uniform
around the frame, there are no
shadows or gaps between the
wall and the frame.
The mica-filled polypropylene
cone achieves new standards in
transient speed and dynamic
range because of its phenomenal
rigidity and high stiffness to mass
ratio. The inverted butyl sur-
round, the BumpBackTM magnet
and the rigid steel basket are all
optimized for large excursions of
B L
E
N
D
I
N
G
H
I
G
H
F I
T
D
E
L
I
T
Y
A
N
D
A R
C
H
I
T
E
C
U
R
E®
CONTINUED OTHER SIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
|