Nikon Switch KT 10FV2 User Manual

Fiber connection: ST connectors  
Fiber optic cable  
Features  
• Complies with IEEE 802.3 10Base-FL standard.  
• A complete interface of the AUI to fiber optic cable link.  
• Flexible selection for half-duplex or full-duplex mode  
• Supports data transfer rate up to 20Mbps for full-duplex  
• Capability for driving the fiber optic cable segment up  
to 2000M (6560 ft.).  
Two ST style connectors are provided for connection to  
fiber optic cable. One is for transmitting and the other is  
for receiving. See the following figure:  
Installation Guide  
Ethernet Fiber Optic Transceiver  
Model: KT-10F v2  
• Selectable SQE test function  
• Link integrity test for automatic checking of fiber  
optic cable lines  
• Supports LED indications for the Transmit, Receive,  
Link, and Collision status.  
• Dimension:  
• Input voltage: 10.2 to 15.75 VDC  
42mmx65mmx20mm  
Fiber mode: multimode  
Wavelength: 850µm  
• Input current: 250mA @12 VDC (typical)  
The transceiver can operate with a variety of fiber optic  
sizes, for example, 50/125µm, 62.5/125µm, and 100/140µm.  
Connectors & Cables  
DOC.G990126-KT10F-V2-K  
P/N: 750-0125-001  
AUI connection: D-sub 15 pin male connector  
AUI drop cable (50 meters max.)  
Setting Switches  
There are two switches which are accessible on the side of  
the transceiver enclosure. The functions of these switches  
are:  
The AUI connector is used for attaching the transceiver to  
the AUI port provided by an Ethernet device such as an  
Ethernet MAC controller, an Ethernet repeater, or an  
Ethernet concentrator via an AUI drop cable. The pin  
assignments are shown as below:  
General Description  
The KT-10F Ethernet transceiver complies with IEEE 802.3  
transceiver specifications and 10Mbps Ethernet CSMA/  
CD operation to extend the your existing Ethernet segment  
up to 2000 meters by using fiber optic cable.  
SW# Setting  
SW1 On  
Off  
SW2 On  
Off  
Function  
Enable SQE test (factory default)  
Disable SQE test (for repeater device)  
Full-duplex mode  
The transceiver is attached to the AUI connector of an  
Ethernet device via standard AUI cable.  
Half-duplex mode (factory default)  
Pin Assignments of the AUI (DB15) Connector  
Pin  
3
Name  
DO +  
DO -  
DO S  
DI +  
DI -  
DI S  
CO +  
CO -  
CO S  
CI +  
CI -  
Pairs  
Use  
Transmit  
Pair  
Data Out (+)  
Data Out (-)  
Data Out Shield  
Data In +  
Important:  
10  
11  
5
12  
4
The transceiver is shipped from the factory with the SQE  
test enabled. If the transceiver is connected to an Ethernet  
repeater, a 10Base-T hub, or a wiring concentrator, the SQE  
test function should be disabled.  
Receive  
Pair  
Data In -  
Data In Shield  
Control Out +  
Control Out -  
Control Shield  
Control In +  
Control In -  
7
15  
8
Optional  
Pair  
2
9
Collision  
Pair  
1
6
13  
14  
CI S  
VC  
VP  
Control Shield  
Voltage Common  
Voltage Plus  
Voltage Shield  
Power  
Pair  
VS  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miller Electric Welding System CST 250 VRD User Manual
MTD Lawn Mower 82 0632 User Manual
Murphy Plumbing Product OS77 Series User Manual
NETGEAR Network Router HR314 User Manual
Nikon Camcorder S9200 User Manual
Nokia Bluetooth Headset BH 302 User Manual
Omega Engineering Network Card BNC 08DI User Manual
Omega Vehicle Security Electric Heater PHCN 410 User Manual
Panasonic Fax Machine KX FPC141 User Manual
Panasonic Telephone 391 User Manual