Download from Www.Somanuals.com. All Manuals Search And Download.
Warning Statement
All contents subject to change without prior notice
WARNING
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his/her own expense.
You are cautioned that any changes or modifications not expressly approved in this manual could void your
authority to operate this equipment. The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B
of Part 15 of FCC Rules.
WARNING
This is a Class A product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
λ
Operate the unit on 100–240 V AC, 50/60 Hz to DC 12V 7A power adaptor.
Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified
personnel before operating it further.
λ
λ
Unplug the unit from the wall outlet or set the power switch to the OFF position if it is not to be used for
several days.
λ
λ
λ
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
The wall outlet should be near the unit and easily accessible.
The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall
outlet with the power switch set to the OFF position.
λ
λ
λ
Do not look into the lens while the lamp is on.
Do not place your hand or objects near the ventilation holes. The air coming out is hot.
Avoid using an extension cord with a low voltage limit, as it may cause short-circuiting and physical
injury.
λ
λ
Do not catch your finger between the unit and surface of the floor when moving the projector installed
on the floor.
Be careful not to catch your finger in the cooling fan.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
λ
λ
λ
λ
λ
λ
λ
λ
λ
λ
λ
Quick cooling function for reducing projector cooling time;
Compact and portable unit;
High quality short throw lens;
Adjustable color balance control for data/video display;
Halogen 75W projection lamp with 3200K color;
Ability to display 16.7 million colors;
Multi-language on-screen menus;
Built-in speaker providing mixed mono audio when an audio input is connected;
Powerful AV function to provide a high quality AV picture;
External Power Adapter with Universal AC Voltage input 100–240V, 12VDC at 7A output;
The apparent brightness of the projected image will vary depending on the ambient lighting conditions,
selected input source contrast/brightness settings, and the projection distance (to which it is directly
proportional).
λ
The lamp brightness will decline over time and may vary within the lamp manufacturer’s specifications.
This is normal behavior and should be expected.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping Contents
The projector is shipped with the cables required for connection to a PC and video output devices. Carefully
unpack the box and verify that you have all of the items shown below. If any of these items are missing,
please contact your place of purchase.
The supplied accessories will be suitable for your region, and may differ from those illustrated.
Projector
User’s manual
AC power adapter
Audio cable
Power cord
S-Video cable
Pull the tab before using the
remote control.
Remote control with battery
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
Front / Upper View
1. External control panel
(See "External control panel" on
page 9 for detailed information.)
2. Ventilation grill
1
4
3
5
3. Lens cap
4. Focus adjuster
5. Front IR remote sensor
2
Left Side View
Refer to "Connection" on page 12 for more information on making connections to various equipment.
8
7
9
6
10
6. 12VDC Power jet input
7. Main Power Switch
9. Video input socket
10. S-Video input socket
8. 3.5mm Audio in Phone Jack
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Right Side View
11
12
11. 2W mono speaker
12. Lamp cover
Lower / Bottom View
13
14
13. Lamp Cover
14. Ceiling mount and adjustable feet
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
External Control Panel
11
10
1
2
9
8
3
4
7
6
5
1. Focus adjuster (lens focus can be adjusted by this key).
2. Power (Refer to "Start up" on page 14 and "Shutdown" on page 15 for more information.)
Turns the projector on or off.
3. Right key. (OSD control only).
4. Down key. (OSD control only).
5. Volume increase. Digital volume control.
6. OSD Menu. Menu recalls for OSD.
7. Volume decrease. Digital volume control.
8. OSD Enter/Source (Refer to "Switching input signal" on page 14 for more information.)
Sequentially selects the input signal Video, S-Video, Component Video, or RGB.
9. Left Key. (OSD control only).
10. Up key. (OSD control only).
11. Top infrared sensor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
POWER – Turns the projector on or off.
SOURCE – Sequentially selects the input signal Video, S-Video, Component Video, or RGB.
MUTE – Audio mute on or off.
Display – Display the video standard and mode.
UP – Up key for OSD control.
LEFT – Left key for OSD control.
RIGHT – Right key for OSD control.
DOWN – Down key for OSD control.
ENTER – Enter key for OSD control.
VOL+ – Volume increase. Digital volume control.
VOL- – Volume decrease. Digital volume control.
MODE – Sequentially selects video mode Dynamic, Static, Theater, or Game.
MENU – OSD menu recall.
ALIGNMENT – Display alignment signal for focus adjustment.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees of the projector’s IR remote control sensors to
function correctly. The distance between the remote control and the sensors should not exceed 6 meters (~
20 feet).
Make sure that there are no obstacles between the
remote control and the IR sensors on the projector
that might obstruct the infra-red beam.
Replacing the remote control battery
1. Pull out the battery holder.
2. Insert the new battery into the holder. Note:
The positive polarity should face outward.
3. Push the holder into the remote control
until it clicks into place.
λ
Avoid excessive heat and humidity. There
may be battery damage if the battery is
incorrectly replaced.
λ
Replace only with the same or equivalent type
battery, as recommended by the battery manufacturer.
Dispose of the used battery according to the manufacturer’s instructions.
Never throw a battery into a fire. There may be danger of an explosion.
If the battery is dead, or if you will not be using the remote control for a long time, remove the battery to
prevent damage to the remote control from the possibility of battery leakage.
λ
λ
λ
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections;
2. Use the correct signal cables for each source; and
3. Ensure that the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see "Shipping
Contents" on page 6). They are commercially available from electronics stores.
Cable connection
Connecting video source devices
This section describes how to connect the projector to video source devices using video cables. Video cable
connections are recommended for video presentations.
You can connect your projector to various video source devices that provide any one of the following output
sockets:
λ
λ
S-Video
Video (composite)
You need only connect the projector to a video source device using just one of the above connecting
methods; however, each provides a different level of video quality. The method you choose will most likely
depend upon the availability of matching terminals on both the projector and the video source device as
described below:
Better video quality
The S-Video method provides a better quality analog video than standard composite video.
If you have both composite Video and S-Video output terminals on your video source device, you should elect to
use the S-Video option.
Lesser video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal, result from your
projector, being the lesser video quality of the available methods described here.
Connecting audio
The projector has a built-in mono speaker that is designed to provide basic audio functionality accompanying data
presentations for business purposes only. It is not designed for, nor intended for, stereo audio reproduction use as
might be expected in home theatre or home cinema applications. Any stereo audio input (if provided) is mixed into a
common mono audio output through the projector speaker.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have a separate sound system, you will most likely want to connect the audio output of your video source
device to that sound system, instead of to the mono audio projector.
The audio connections illustrated in the following sections are provided for informational purposes only. You need
not connect audio to the projector if there is an alternate sound system available, or if audio is not required.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Start-up
1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted).
Check that the Power indicator on our projector adapter lights orange after power has been applied.
2. Plug the DC plug into the projector’s 12VDC socket. Remove the lens cap. If it is left on, it could become
deformed due to the heat produced by the projection lamp.
3. Switch on the main power at the left side of the projector. Check that the Power inductor on the projector
lights green.
3. Press the Power button on the remote control or projector to start the unit. The Power indicator lights off
and lights green after 3 seconds when the unit is on.
4. The start-up procedure takes about 5 seconds after pressing Power, and the image will appear as normal
(If necessary). Rotate the focus ring to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 45
seconds before energizing the lamp.
5. Switch all of the connected equipment on.
6. You can also press Source on the projector or remote control to select your desired input signal. For more
information, please refer to "Switching input signal" on page 14.
If the frequency/ resolution of the input signal exceed the projector’s operating range, you will see the
message “Out Range” displayed on a blue screen.
Switching input signal
The projector can be connected to multiple devices at the same time;
however, it can only display one at a time. To cycle through the available
input sources, press the Enter button on the projector control panel, or the
Source button on the remote control. The selected source name will display
at the Top-Left of the screen for 10 seconds after each button press.
The brightness level of the projected image will change accordingly
when you switch between different input signals. Data (graphic) "PC"
presentations using mostly static images are generally brighter than
"Video" presentations using mostly moving images (movies).
The input type affects the options available for the Application Mode. See "Selecting an application
mode" on page 18 for details.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutdown
1. Press Power to turn the projector off.
2. The Power indicator light flashes green and the lamp shuts down. The fans continue to run for
approximately 45 seconds to cool down the projector.
λ
λ
To protect the lamp, the projector will not respond to any commands during the cooling process.
To shorten the cooling time, you can also activate the Quick Cooling function.
3. Switch off the main Power at the left side and disconnect the power cord at the adaptor from the wall
socket.
λ
Do not unplug the adaptor or power cord before the projector shutdown sequence is complete, or
during the 45-second cooling down process.
λ
If the projector is not properly shut down, you risk damaging the lamp. Do not move the projector while
the lamp is hot.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Menu system
OSD MENU1
Video
S-Vide
Dynamic
Static
Theater
Game
Front/Up
Front/Down
Rear/Up
Rear/Down
OSD Menu 2
0 to 100 Brightness (Default 50)
0 to 100 Contrast (Default 50)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
0 to 100 Color (Default 50)
OSD Menu 3
0 to 100 Hue (Default 50)
English
French
German
Spanish
Portuguese
Italian
System Default
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture menus
Some picture adjustments are available only when certain input sources are in use.
FUNCTION
(Default setting
/ Value)
DESCRIPTION
Source Input
1. Video Input: RCA composite video
2. S-Video Input: Mini DIN5 S-Video
Video Mode
1. Dynamic (Default): Is suitable for enjoying colorful movies and TV in a blackened
living room lighting level environment.
2. Static Mode: Is suitable for enjoying DVD movies and TV best viewed in a darkened
(not bright) lounge room environment.
3. Theater Mode: Is suitable for playing cinema movies in a totally darkened living
room lighting level environment.
4. Gaming Mode: Is suitable for playing gamebox-based video games in a normal
living room lighting level environment.
Flip/Mirror
Brightness
1. Front/Down: Front projection on floor
2. Front/Up: Front projection on ceiling
3. Rear/Up: Rear projection on ceiling
4. Rear/Down: Rear projection on floor
Adjusts the brightness of the image. The higher the value, the brighter the image; the
lower the setting, the darker the image. Adjust this control so that the black areas of
the image appear as black and the detail in the dark areas is visible.
Contrast
Adjusts the degree of difference between dark and light in the image. The higher the
value, the greater the contrast. Use this to set the peak white level after you have
previously adjusted the Brightness setting to suit your selected input and viewing
environment.
Color
Increases or decreases the color intensity of the image.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hue
Adjusts the color tones of the image. The higher the value, the more greenish the
image becomes. The lower the value, the more reddish the image becomes.
Language sets the language for the OSD control menus.
Use Left / Right on the projector, or Left / Right on the remote control, to
select your desired language.
Language
Default
Returns all settings to the factory preset values.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
THE PROJECTOR DOES NOT TURN ON.
Cause
Remedy
There is no power from the power cable.
Plug the power cord into the AC inlet on the projector,
and plug the power cord from the power outlet. If the
power outlet has a switch, make sure that it is switched
on.
Attempting to turn the projector on again during the
cooling process.
Wait until the cooling down process has completed.
NO PICTURE.
Cause
Remedy
Turn the video source on and check that the signal
cable is connected correctly.
The video source is not turned on or connected
correctly.
The projector is not correctly connected to the input
source device.
Check the connection.
The input signal has not been correctly selected.
Select the correct input signal with the Source key on
the projector or remote control.
The lens cap is still attached to the lens.
Remove the lens cap.
BLURRED IMAGE.
Cause
Remedy
The projection lens is not correctly focused.
The projector and the screen are not aligned properly.
Adjust the focus of the lens using the focus adjuster.
Adjust the projection angle and direction, as well as the
height of the unit (if necessary).
The lens cap is still attached to the lens.
Remove the lens cap.
REMOTE CONTROL DOES NOT WORK.
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the remote control and the Remove the obstacle.
projector.
You are too far away from the projector.
Stand within 6 meters (19.5 feet) of the projector.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
λ
λ
Use a canister of compressed air to remove dust.
If there is dirt or smearing, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe
the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as described in "Shutdown"
on page 15, and unplug the power cord.
λ
λ
To remove dirt or dust, wipe the case with the supplied cleaning cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral PH detergent. Then wipe the
case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case
.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
λ
Make sure the temperature and humidity of the storage area are within the recommended range for the
projector. Please refer to "Specifications" on page 22, or consult your dealer about the range.
Retract the adjuster feet.
λ
λ
λ
Remove the batteries from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When you carry the projector
yourself, please use the original box or the soft carry case that is provided.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
* All specifications are subject to change without notice.
Display Technology
Resolution
Single Liquid Crystal on Silicon (LCoS) Display
640 x 480 x RGB
Contrast Ratio
600:1 (Full On/Full Off)
75W Halogen, 1000 hours STD
Video: 480i, 576i
Lamp Type and Life
Maximum Resolution
Dimensions (WxHxD)
9.44 x 3.54 x 7.9 inches
240mm x 90mm x 200mm
Aspect Ratio
4:3 Standard
Noise Level
<32dB
Projection Lens
Image Size
f=24.0 – 30.1 mm, F/2.4-2.50
30 to 90 inch (1.5 to 3 meters)
NTSC, PAL, 480i, 576i
Video Compatibility
Displayable Colors
Projection Method
Power Supply
8-bit per channel color processing
Front/rear/ceiling mount/table top
AC/DC Adapter, 100~240VAC, 50-60Hz, 12VDC 7A
Power Consumption
84 watts,
<5 watts in standby mode
Operating Temperature
I/O Connectors
23 to 102 F (-5 to 42C), 80% maximum humidity
S-Video, 3.5mm Line-in, Triple IR receivers
OSD Language
English, French, German, Spanish, Portuguese, Italian
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
90
240
200
Unit: mm
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Limited Warranty
NEXTAR warrants this product against any defects in material and workmanship, under normal usage and
storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be
defective within the warranty period, NEXTAR’s only obligation—and your exclusive remedy—shall be
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer
from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance with
NEXTAR’s written instructions, especially the requirement that ambient humidity must be between 10% and
90%, temperature between 0 degrees centigrade and 40 degrees centigrade, altitude lower than 10000 feet, and
avoidance of operation of the projector in a dusty environment. This warranty gives you specific legal rights, and
you may have other rights that vary from country to country.
Please refer to the warranty card. Limited warranty is subject to change without notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Nextar may find it necessary to modify, amend or otherwise change or update this manual.
We reserve the right to do this any time, without any prior notice. All specifications and features are subject to
change without notice.
All screen shots shown are simulated and may not represent the actual screen on production units sold to
consumers.
For instruction manuals, updated drivers or other information, be sure to visit our website at:
Or write us at:
Nextar
1661 Fairplex Dr.
La Verne, CA USA 91750
25
Download from Www.Somanuals.com. All Manuals Search And Download.
|
