Industrial Modem
Designed for unattended sites
•
•
Designed to survive harsh environmental conditions for unattended operation,
such as remote monitoring.
Dual Watchdog Timers which can restart the modem if the modem crashes, starts
executing invalid code or has a power interruption.
•
•
Fully customisable.
A unique voice messaging system that can be used as a voice mail box or
answering machine.
•
•
•
•
Dial & Talk Alarm feature.
Automatic Power Off when modem is not used.
No internal batteries for non-volatile storage ensuring a long life.
Small rugged packaging.
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Contact Information
Please contact NetComm for help, information, sales enquiries or to join the NetComm Info Mailing List:
Technical Support
Web Page:
Phone: (02) 9870 2332
Fax: (02) 9870 2619
TeleMarketing
Phone: (02) 9424 2056
Fax:
(02) 9424 2525
Mailing List
For the latest sales and technical information, subscribe to the NetComm Info Mailing List by sending an e-mail to:
In the body of the message enter the word:
subscribe
This will add your e-mail address to the NetComm Information Mailing List and you will be e-mailed news and
updates regularly.
YML391-3A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Legal & Regulatory Information
Copyright Information
This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or
review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or
transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior
written permission of NetComm Limited.
NetComm Limited accepts no liability or responsibility, for consequences arising from the use of this product.
NetComm limited reserves the right to change the specifications and operating details of this product without
notice.
NetComm is a registered trademark of NetComm Limited.
All other trademarks are acknowledged the property of their respective owners.
Australian Customer Information
Austel (The Australian Telecommunications Authority) requires you to be aware of the following information and
warnings:
Users may experience minor audio distortion when using this product. This distortion may be generated by the low
bit rate for voice sampling.
Some of the modem default settings have been selected to comply with Austel technical specifications. If you
intend to change any default settings you must comply with the following rules:
1. The modem must not answer an incoming call less than two seconds after the first ring signal. As a Òrule-of-
thumbÓ your modem should be set so it answers incoming calls after the second ring (ATS0=2).
2. If Busy signal detection is switched off, the modem must not attempt more than two automatic redials and
must wait at least two seconds before redialling.
3. If Busy signal detection is switched on, the modem must not attempt more than nine automatic redials and
must wait at least two seconds before redialling.
4. If, after redialling the maximum number of times, the modem is still unable to establish a connection you must
wait 30 minutes before attempting to redial.
5. The use of Bell standard 103 and 212A is not permitted in Australia. Use of these modes will cause your
modem to lose its permit status.
Changing the default values of the modem, in such a way as to cause your modem to operate in a non-compliant
manner when connected to a telecommunications network operated by a carrier, is contrary to the
Telecommunications Act 1991 and may result in penalties of $12,000.
New Zealand Customer Information
New Zealand Telecom requires you to be aware of these important warnings:
This equipment may not necessarily provide for the effective hand-over of a call to or from a telephone connected
to the same line.
The operation of this equipment on the same line as telephones or other equipment with audible warning devices or
automatic ring detectors will give rise to bell tinkle or noise and may cause false tripping of the ring detector.
Should such problems occur, the user is not to contact Telecom Faults Service.
The telephone associated with the authorised apparatus must be permitted for connection to the New Zealand
public telephone network.
The transmit level from this device is set at a fixed level and because of this there may be circumstances where the
device does not give its optimum performance. Before reporting such occurrences as faults, please check the line
with a standard Telepermitted telephone, and do not report a fault unless the telephone performance is impaired.
YML391-3A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
If your modem ever suffers physical damage that causes its internal parts to become exposed, it should be
disconnected from the phone line immediately. The modem must then be repaired before reconnection to the phone
line is permissible.
Should it be necessary to physically move your modem, disconnect it from the phone line or earthing lead before
disconnecting the power connection. When reconnecting your modem, reconnect the power or earthing lead before
reconnecting it to the phone line.
Some parameters required for compliance with TelecomÕs PTC Specifications are dependent on the equipment
connected to the RS 232 port. The connected equipment shall be set to operate within the following limits for
compliance with Telecom Specifications:
1. Equipment connected to the RS 232 port shall be certified to meet the requirements of Reg. 18 of the New
Zealand Wiring Regulations 1976.
2. When the user manually initiates a call, via equipment connected to the RS232 port, the equipment shall
operate within the following restrictions:
a. Not more than 5 call attempts shall be made to the same number within a one hour period.
b. There shall be at least 60 seconds between call attempts.
c. Not more than a total of 10 call attempts shall be made to the same number for any single manual call
initiation.
d. Automatic calls to different numbers shall be not less than 5 seconds apart.
FAILURE TO MEET THE ABOVE REQUIREMENTS MAY NEGATE THE USER RIGHTS UNDER THE
TELECOM TERMS OF SERVICE.
When operating in V.22bis or V.22 mode over some older telephone exchanges, it may be necessary to issue the
&G2 command.
Setting the S0 register (auto-answer) to S0 = 1 or to values greater than 5 will render this equipment non-compliant
with the Telepermit requirements.
This equipment does not provide a guard tone with the V.22 and V.22bis answer modes. In some circumstances
this could cause interference with the telephone network signalling systems, and could result in lost calls. Telecom
will not accept responsibility should such problems occur. Such occurrences will be rare.
The preferred method is to use DTMF tones (ATDT...) as this is faster than pulse (decadic) dialling, and is
available on most New Zealand telephone exchanges. Where DTMF is not available and decadic must be used,
your communications software must be set up to record numbers according to the following translation table as the
modem is not directly compatible with the New Zealand (10-N) Reverse dialling standard.
Number to be dialled
Number to program into computer
0
1
2
3
4
5
6
7
8
9
0
9
8
7
6
5
4
3
2
1
Note that where DTMF dialling is used, the numbers should be entered normally.
YML391-3A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Introduction
This manual provides a brief introduction to the Industrial SmartModem and gives an overview of the features and
commands available.
The IG6000 Industrial SmartModem has a SmartModem 336 core with additional features that make it suitable for
industrial and unattended operation. Particular attention has been paid to ensuring that the modem restarts reliably
in the event of power interruption or internal malfunction. The modem uses the latest generation Rockwell DSP
which will enable new features to be soft-uploadable when they become available.
YML391-3A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Modem Controls and Indicators
Links (Internal controls)
LK1
1
2
Set factory defaults
Normal
LK2
LK3
LK4
LK5
LK6
LK7
LK8
1
1
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
1
2
Power down disabled
DTR wakeup enabled
None DTR wakeup disabled
Link connects RS232 shield to ground
PSTN
LK9
PSTN IN
OUT
Leased Line
LEDS
DCD - Data Carrier Detect (Inner LED)
LED will glow when the modem detects a valid carrier signal from a remote modem.
PWR - Power (Outer LED)
LED will glow to indicate when the modem is turned on. LED will be off when the modem is in power down
mode.
YML391-3A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Modem Features
Power Down Feature
S119 can be set with the number of seconds of no activity before the modem shuts down. The modem will not shut
down if DTR is asserted, if the modem is connected, any key on the keyboard is pressed or an alarm switch is on.
The modem will wake up if:
•
•
•
DTR is raised
there is a Ringing signal or
an alarm switch is asserted.
S119 defaults to 0 (power down disabled).
The modem draws almost no power when powered down.
Dial and Talk Feature
This feature enables a modem to alert, by spoken word, that an alarm situation at a remote site needs attention. The
modems can be configured to dial up to 10 preset numbers and speak a stored message when one of two external
switches are closed.
These switches will connect to pins 12 and 7 (alarm 1) and pins 13 and 7 (alarm2) of the RS232 connector. An
alarm condition is recognised when a short circuit is applied across either pair of pins, eg by use of a relay.
By default to modem will ring stored number 0 if either alarm switch is closed.
To set stored number 0 type:
AT&Z0 = nnnnnnnnnn where nnnnnnnn is the phone number.
You may store up to 10 numbers using &Z0 to &Z9.
The numbers to ring for each alarm can be specified by the AT#ALM command:
AT#ALM1=1,4,8,3
Means than if alarm switch 1 is pressed the modem should ring the stored numbers 1 then 4 then 8 then 3.
AT#ALM2= 9
Means that if alarm switch 2 is pressed dial stored number 9.
YML391-3A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Voice Messaging System
This feature can be installed into an IG6000 by downloading a vocabulary file to the modem to enable it to respond
to DTMF tones from a remote modem.
If this feature is enabled by using the #MEM command:
AT#MEM1
AT#MEM2
AT#MEM0
Modem will answer in voice mode after S110 rings if DTR is low
Modem will answer in voice mode after S110 rings regardless of DTR
All voice features off
Dial the modem and wait for it to answer. After the number of rings specified by S110 (default 4) the modem will
answer the call and respond with "Leave a Message after the Beep". If you key in a DTMF digit during the time
this message is played, the message will stop and you can complete entering the PIN number. The factory default
PIN number is 1234. This can be changed by using the new #PIN command.
AT#PINnn…nnn
where nn…nnn is the pin number. Up to 10 digits of PIN number can be specified
If you key in the correct PIN number the modem will say "OK" and ask for a command. You may key in 0 for a
menu of available functions.
Functions Available using DTMF keys
1-9
*1
*2
*3
*4
*5
*6
*9
*0
##
Play back stored message 1 to 20
Record a new welcome message to replace "Leave a Message after the Beep"
Record a new message
Playback the current welcome message
Report number of stored messages and the state of the alarm switches (ON or OFF)
Play all messages
Enable / disable answering machine record function
Erase stored messages but retain the welcome message
Erase all stored messages including the welcome message (return to factory default message)
Hang up
Messages 1 and 2 are used by the alarm switches. Other messages can be stored and used as a voice mail box
which can be shared by a group of people who know the PIN number.
If no pin number is entered the user can leave a message after the welcome message beep.
+
To avoid recording a lot of silence the messages can be terminated with the # DTMF key.
About 8 minutes of voice storage in a maximum of 20 individual messages is available.
How to Load the Voice Alarm Messages
If you have not downloaded a vocabulary file use the following procedure:
1.
2.
3.
4.
5.
Connect the modem to a PC running a terminal program (like Hyperterm).
Type ATS119=0 to stop modem going to sleep.
Type AT#MINI and wait for EPROMs to erase. The modem will beep when ready.
Type AT#MEM2 to put the modem into voice answering mode.
Connect modem to phone line and using a touch tone phone dial the modem. The modem will answer
with a brief message "Leave a message after the beep!"
6.
Record your message into the modem for Alarm Condition #1, leaving 2 seconds of silence after the beep
before speaking.
YML391-3A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
7.
8.
9.
Press the # button on the phone when your message is finished.
Hang up the phone wait a few seconds.
Ring the modem again and record a second message for Alarm #2 following steps 8 and 9. Your
messages are now recorded.
10.
11.
Reconnect modem to a terminal program and type AT#MCD to display the stored messages. The duration
of the 2 messages you have recorded should be visible.
If you wish the modem to answer calls in data mode type AT#MEM0&W in a terminal program to turn
off the voice answering function or AT#MEM1 if you want the voice answering function only when DTR
is low.
To redo the messages, erase the EPROMs using AT#MINI and record the messages again.
Remote Voice Setting of Alarm Messages
If you have installed the vocabulary file, use the procedure detailed in the VOICE MESSAGING SYSTEM to enter
the modem PIN number then use DTMF command *2 the record the first message then enter *2 again to enter the
second message. You may playback the messages immediately by keying DTMF 1 and DTMF 2 to verify that they
sound OK.
Hang up by keying ##.
YML391-3A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Operating Modes
Asynchronous Mode
Asynchronous Mode is the normal default mode of the modem. Control and monitoring is performed by executing
the AT commands using a PC fitted with suitable communications software.
Synchronous Operation
Your modem supports two synchronous modes. Mode 1 allows operation with computers which support
asynchronous and synchronous communication on a single RS-232 port. Mode 2 allows your modem to be
operated with dedicated synchronous terminals.
Although your modem can only operate over a single two-wire connection, it will still perform full-duplex
synchronous communication. Half-duplex operation could be simulated by controlling the state of the RTS and
CTS signals.
Terminal Speeds
Your synchronous terminal or host should use the clock signals provided by the modem to synchronise transmit
and receive data. The clock speed will represent the actual connection speed of the modem.
+
When synchronous mode is selected, your modem cannot operate in constant speed mode or use the error
correction or data compression facilities of the modem. Only variable speed mode is available in synchronous
connections (this refers to the modem's terminal speed).
Line Speeds
Your modem supports a number of synchronous line speeds.
When operating in synchronous mode, your modem should always be configured with a locked, non-auto-ranging
B setting (this refers to modem line speed).
For V.34, the B setting only sets the maximum speed. The modem will automatically determine the highest usable
speed for the line.
Synchronous Mode 1
Synchronous mode 1 is selected with the &M1 command.
•
Type: AT&M1 <E>
Your modem will enter synchronous mode whenever it successfully connects to a remote modem.
You should also:
Type: AT&D2 <E>
This allows hang up via your computerÕs DTR signal.
To return to asynchronous operation:
Type: AT&M0 <E>
•
•
Synchronous Mode 2
Synchronous mode 2 is selected with the &M2 command.
•
Type: AT&M2 <E>
Your modem will enter synchronous mode whenever it successfully connects to a remote modem.
You should also:
•
Type: AT&D2 <E>
This allows you to dial and hang up.
YML391-3A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
When the terminal asserts the DTR signal (DTR makes an OFF-ON transition), your modem will dial stored phone
number zero. The phone number may contain dial modifiers.
To return to asynchronous mode:
•
Type: AT&M0 <E>
Your modem will remain in asynchronous mode.
Leased Line Operation
A leased line, or private line, is a telephone line that permanently connects two or more locations. The leased line
does not have any switching equipment associated with it.
Leased-line operation with the modem is selected with the &L command.
If you select leased line operation with the &L1 command, you must issue the ATA command to answer a call, and
the ATD command to initiate a call.
If you use &L2 or &L3 to select Auto leased line operation, you do not need to issue the ATA or ATD commands;
&L2 selects Originate mode automatically and &L3 selects Answer mode automatically. To dial or answer, raise
DTR; to hang up and return to local command state, lower DTR.
+
You will require a special phone cable (available from your dealer) to connect your modem to a leased-
line socket. The phone cable supplied with your modem is suitable for use with normal, dial-up, voice (PSTN)
lines.
Before commencing leased-line communications, it is recommended that a non-auto-ranging B setting be specified.
+
If error correction is required, select a Reliable mode, not an Auto-Reliable mode. (See the \N command.)
Auto-ranging and fallback are disabled in leased-line mode. Your modem will only attempt to connect using the
communications standard specified by the B command and the terminal speed.
Once a connection has been established, if your modem detects a loss of carrier it will continuously attempt to re-
establish the connection.
If the modem is in auto leased-line operation and this configuration has ben stored in memory using the AT&W
command, a timeout period of 10 seconds is available after power up to disable the leased-line mode via the AT&O
command. Alternatively, this command can be sent with DTR low.
YML391-3A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Modem AT Commands
Your Industrial Modem ª has a number of specific commands that control and enhance its operation. To access and
change these commands open a local terminal connection with your modem using your preferred communications
software, such as WinFax Pro, and type the letters AT followed by the specific command and press <Enter>. The
AT commands are case insensitive and may be entered in either lower or capital letters.
n
indicates the default settings
Commands
Command
Description
A
D
H
O
Answer call
Dial number
Hang up modem
Enter On-line state
Dial Modifiers
Dial Digits
0-9, A, B, C, D, #, *
,
Pause while dialling
F or ^
Disable calling tones
J
Initiate MNP 10 at 1200 bps (V.22)
MNP 10 cellular power level adjustment for this call
Redial last number
K
L
M
P
Initiate MNP 10 at 4800 bps (V.32)
Pulse dial number
R
S=n
T
Switch to answer mode
Dial stored number ÔnÕ (where n=0-9)
Tone dial number
W
;
Wait for dial tone
Return to Local command state
Hook flash
!
@
Wait for quiet answer
YML391-3A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
General Commands
+++
?
Escape Sequence
Displays help. May be followed by the command(s) or a keyword for which
help is needed
A/
Repeat Command
B0
n
Auto-Connect
B1
Auto-Connect
B2
Auto-Connect
B3
V.21 - 300 bps
B4
Bell 103 - 300 bps
B5
V.23 - 1200/75 bps
B6
V.22 - 1200 bps
B7
B8
Bell 212A - 1200 bps
V.22bis - 2400 bps
B9
Auto-Connect
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
E0
V.32 - 4800 bps
V.32bis - 7200 bps
V.32 (Non-TCM) - 9600 bps
V.32 - 9600 bps
V.32bis - 12000 bps
V.32bis - 14400 bps
V.34/V.Fast Class - 14400 bps
V.34/V.Fast Class - 16800 bps
V.34/V.Fast Class - 19200 bps
V.34/V.Fast Class - 21600 bps
V.34/V.Fast Class - 24000 bps
V.34/V.Fast Class - 26400 bps
V.34/V.Fast Class - 28800 bps
V.34 31200 bps
V.34 33600 bps
Local command state echo off
Local command state echo on
Go on-hook
E1
n
H0
H1
I0
I1
I2
Go off-hook
Numeric firmware identity
Checksum of firmware - return checksum
Checksum of firmware - return OK/ERROR
Modem Model
I3
I4
I5
Firmware Version and date
Manufacturer ID
I9
I10
L0
Verbal firmware identity
Display modem statistics
Lowest volume level
L1
Low volume level
L2
L3
M0
M1
M2
M3
n
n
Medium volume level
Highest volume level
Speaker is always off
Speaker on when connecting, off when connected
Speaker always on
Speaker off when dialling or after connection established
YML391-3A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
M4
O1
O2
O3
O4
O5
O6
O7
P
Speaker on during dial, answer, retrain or rate change
Enter On-line state and force communication retrain (V.22bis and V.32bis only)
Retrain, donÕt go on-line (V.22bis & V.32bis)
Change line speed to 4800 bps (V.32 & V.32bis)
Change line speed to 7200 bps (V.32 & V.32bis)
Change line speed to 9600 bps (V.32 & V.32bis)
Change line speed to 12000 bps (V.32 & V.32bis)
Change line speed to 14400 bps (V.32 & V.32bis)
Pulse dialling
Q0
n
Modem returns response codes
Q1
Q2
R9
Modem does not return response codes
Modem does not return RINGING or response codes when answering
9600 bps (locked terminal speed - no autobaud)
14,400 bps (locked terminal speed - no autobaud)
19,200 bps (locked terminal speed - no autobaud)
28,800 bps (locked terminal speed - no autobaud)
38,400 bps (locked terminal speed - no autobaud)
57,600 bps (locked terminal speed - no autobaud)
115,200 bps (locked terminal speed - no autobaud)
230,400 bps (locked terminal speed - no autobaud)
Display value in S Register ÔnÕ
R14
R19
R28
R38
R57
R115
R230
Sn?
Sn=x
T
Place ÔxÕ in S Register ÔnÕ
Tone dialling
Numeric response codes
Verbal response codes
n
n
V0
V1
W0
W1
W2
X0
CONNECT message reports the terminal speed
CONNECT message reports the terminal speed
CONNECT message reports the line speed
Basic response codes (codes 0-4,8)
n
X1
X2
X3
X4
X5
X6
Zn
&B0
&B1
&B2
&B3
&B4
&C0
&C1
&C2
&C3
&D0
&D1
&D2
Extended response codes (codes 0-5,8,10-12,30-40,60-62)
Extended response codes (codes 0-6,8,10-12,30-40,60-62)
Extended response codes (codes 0-5,7,8,10-12,30-40,60-62)
Extended response codes (codes 0-7,10-12,30-40,60-62)
Extended response codes (codes 0-7,10-13,30-40,60-62)
Extended response codes (codes 0-5,7-8,10-13,30-40,60-62)
Restore configuration profile n (n=0,1,2,3)
8 bit character length
9 bit character length
10 bit character length
11 bit character length
10 or 11 bit character length determined by autobaud
DCD signal always asserted
n
n
n
DCD signal responds to remote modem
DCD signal always on, pulses low on disconnect
DCD asserted during voice session
Ignore DTR
Return to Local command state if DTR goes low
n
Hangup & return to Local Com if DTR goes low, disable auto-answer until DTR
asserted
&D3
&F0
Initialise with values in &Y profile if DTR goes low
Restore factory defaults
YML391-3A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
&F1
Restore non-error correction factory defaults
&F.
Reset modem (clear security database/Telephone numbers)
No guard tone generated
550 Hz guard tone generated
1800 Hz guard tone generated
Flow control disabled
RTS/CTS flow control
XON/XOFF flow control
Transparent XON/XOFF flow control
Failsafe flow control
Asynchronous mode
Abort dial character disabled
Abort dial character enabled
39/61 make/break ratio (USA)
33/67 make/break ratio (Aus/UK)
DSR signal always asserted
DSR signal asserted at start of handshake
DSR signal asserted at end of handshake (before CONNECT message)
Terminate current test
Local Analogue Loopback test
Local Digital Loopback test
Grant Remote Digital Loopback test
Deny Remote Digital Loopback test
Remote Digital Loopback test
Remote Digital Loopback with Self-test
Local Analog Loopback with Self-test
View active configuration profile
View stored profile (n=0-3)
&G0
&G1
&G2
&K0
&K3
&K4
&K5
&K9
&M0
&N0
&N1
&P0
n
n
n
n
n
n
&P1
&S0
&S1
&S2
&T0
&T1
&T3
&T4
&T5
&T6
&T7
&T8
&V
&Vn
&V8
&Wn
&Yn
&Zn=x
#A0
n
View differences between active and default
Save current configuration into stored profile n (n=0,1,2,3)
Select stored profile n for Power on and &D3
Store x as phone number n (x=0-9)
Prevent Remote Access
#A1
Allow remote access
#A2
#ALMn=x
#B0
#B1
#C0
n
n
Allow remote access with security password
Dial number/s x (x=0-9 in &Z) for remote alert n
In 1200bps originate mode B0=V.23, B2=V.22
In 1200bps originate mode B0=V.22, B2=V.23
V.25 calling tones disabled
#C1
#J0
#J1
#K0
n
n
n
V.25 calling tones enabled
Assume V.42 compatibility
Check V.42 compatibility
Disable MNP 10
#K1
Enable MNP 10
#K2
Enable MNP 10 for Cellular links
All voice features off
Voice mode after S110 rings if DTR is low
Voice mode after S110 rings regardless of DTR
Erase Voice mode alarm message
AT command operation
#MEM0
#MEM1
#MEM2
#MINI
#M0
#O0
n
n
n
Characters ignored if modem buffers overflow
YML391-3A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
#O1
Disconnects if terminal buffer overflows
#O2
#O3
#PIN=n
#R0
Disconnects if line buffer overflows
Disconnects if either buffer overflows
Pin Number where n is the pin number
Remote Control Mode
#V0
#V1
Command and S Register verifier off
Command and S Register verifier on
S0=0 setting after AT&F
n
n
%B0
%B1
%C0
%C1
%C2
%C3
%Dn
%E0
%E1
%E2
%H0
%H1
%H2
%H3
%H9
%K0
%K1
%L0
%Ln
%M0
%M1
%N0
%N1
%N2
%P0
%P1
%Q
%R0
%R1
%R2
%S0
%S1
%T0
%T1
%U0
%U1
%U2
%W0
%W1
\A0
S0=2 setting after AT&F
Compression disabled
MNP 5 compression enabled
V.42bis data compression enabled
V.42bis data compression enabled with fallback to MNP 5
Set disconnect delay to n seconds (default %D0)
Disable auto-retrain
Enable auto-retrain
Automatic Speed Stepping
Use B setting for initial MNP 10 connection speed
Initial connection is made at 1200 bps (MNP 10)
Initial connection is made at 4800 bps (MNP 10)
Initial connection is made at 9600 bps (MNP 10)
Use B setting for connection but do not upshift (MNP 10)
CTS operates normally
n
n
n
n
CTS off during dial and handshake
Report current received signal level (-dBm)
Set transmit level (n=11 to 19; -11dBm to -19dBm)
Mode LEDs indicate connection speed
Mode LEDs indicate line quality, V.42/MNP errors & flow ctrl
Standard Baud Rates
n
n
Standard to 14400 then 20800, 31200, 41600 and 62400
Standard to 38400 then 51200
n
n
CONNECT message appears before DCD asserted
CONNECT message appears after DCD asserted
Report current line quality (EQM) (0=perfect)
&R command determines state of CTS
CTS always follows RTS (not reset by &F)
CTS follows DTR when offline (not reset by &F)
DSR is not overridden
DSR mimics the state of DTR (not reset by &F)
DCD always follows state of carrier
DCD is always high (not reset by &F)
Standard error correction response codes
V.42 response codes when V.42 connection established
V.42 response codes for V.42 connections, MNP 2,4,10 compression
Disable welcome message
n
n
n
n
n
Send message specified by *W to remote modem after connect
MNP block size = 64
MNP block size = 128
MNP block size = 192
MNP block size = 256
\A1
\A2
\A3
\Bn
Send Break sequence to remote modem (default \B3)
YML391-3A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
\J0
\J1
n
Fallback to direct mode disabled
Fallback to direct mode enabled
Received Break control (default \K5)
Constant speed mode
Variable speed mode
MNP reliable mode
V.42/MNP auto-reliable mode
V.42 reliable mode
V.42 auto-reliable mode
V.42/MNP reliable mode, fallback to MNP reliable mode
MNP auto-reliable mode
Flow control disabled
XON/XOFF flow control from modem and computer
CTS flow control
CTS-RTS flow control (same as &K3)
Modem-only XON/XOFF flow control
CTS flow control (CTS low until connection)
CTS-RTS flow control - CTS low until connect
Display active configuration with detailed description
Set inactivity timer to n seconds (Default \T0)
Disable reliable response codes
Enable reliable response codes
Extended response codes
Extended response codes with diagnostic information
XON/XOFF pass through disabled
XON/XOFF pass through enabled
Enable V.34
\Kn
\N0
\N1
\N2
\N3
\N4
\N5
\N6
\N7
\Q0
\Q1
\Q2
\Q3
\Q4
\Q5
\Q6
\S
\Tn
\V0
\V1
\V8
\V9
\X0
\X1
*C0
*C1
*Wttt...tt
n
n
n
n
Disable V.34 use V.FC
Specify welcome message text used by %W1(ttt...tt = text use | for new line)
Modulation Setting
+MS?
Report selected options
+MS=?
+MS=
<mod>
Report list of supported options
<mod>,<automode>,<min_rate>,<max_rate><E>
see table
<automode>
<automode>
<min_rate>
<max_rate>
=0 (automode disabled, fixed modulation)
=1 (automode enabled, auto select speed/mod)
=lowest rate for modem connection
=highest rate for modem connection
<mod>
0
Modulation
V.21
Possible Rates (bps)
300
1
V.22
1200
2
3
V.22bis
V.23
2400 or 1200
1200
9
V.32
9600 or 4800
10
11 n
V.32bis
V.34
14400, 12000, 9600, 7200,or 4800
33,600, 31,200, 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000,
9600, 7200, 4800, or 2400
64
69
Bell 103
Bell 212
300
1200
YML391-3A
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Distinctive Ring
The Industrial Modem is able to discriminate between three different types of rings. This is useful if you purchase
the Telstra Duet service. With Telstra Duet, two phone numbers are shared for one telephone line. One number
can be used for Voice and the other number can be used for your Modem. To enable the modem to answer only
when your modem number is dialled, issue the command: AT-SDR=4 S0=2&W.
AT-SDR=n,x
where n=0 to 7, default=0,
x=0 Disable Distinctive Ring response suffix;
x=1 Enable Distinctive Ring response suffix (default)
Any ring detected and reported as "RING"
AT-SDR=0
AT-SDR=1,1
AT-SDR=1,0
AT-SDR=2,1
AT-SDR=2,0
AT-SDR=3,1
AT-SDR=3,0
AT-SDR=4,1
AT-SDR=4,0
AT-SDR=5,1
AT-SDR=5,0
AT-SDR=6,1
AT-SDR=6,0
AT-SDR=7
Single ring detected and reported as "RING1"
Single ring detected and reported as "RING"
Double ring detected and reported as "RING2"
Double ring detected and reported as "RING"
Single and double ring detected and reported as "RING1"or"RING2"
Single and double ring detected and reported as "RING"
Triple ring detected and reported as "RING3"
Triple ring detected and reported as "RING"
Single and triple ring detected and reported as "RING1"or"RING3"
Single and triple ring detected and reported as "RING"
Double and triple ring detected and reported as "RING2"or"RING3"
Double and triple ring detected and reported as "RING"
Any ring detected and reported as "RING1"or "RING2"or"RING3"
+
Use AT-SDR=4 for Telstra's Duet service. Do not set Auto Answer below 2 when Distinctive Ring is
enabled.
YML391-3A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Response Codes
Num
0
Verbal
OK
Description
Command accepted
1
2
3
4
CONNECT
RING
NO CARRIER
ERROR
Connection established
Incoming call detected
Carrier not detected
Command error
6
7
8
13
5
NO DIALTONE
BUSY
NO ANSWER
RINGING
Dial tone has not been detected
The number dialled is busy
Silence not detected
The number dialled is ringing
Connected at 1200 bps
Connected at 2400 bps
Connected at 4800 bps
Connected at 7200 bps
Connected at 9600 bps
Connected at 12000 bps
Connected at 14400 bps
Connected at 16800 bps
Connected at 19200 bps
Connected at 21600 bps
Connected at 24000 bps
Connected at 26400 bps
Connected at 28800 bps
Connected at 31200 bps
Connected at 33600 bps
CONNECT 1200
CONNECT 2400
CONNECT 4800
CONNECT 7200
CONNECT 9600
CONNECT 12000
CONNECT 14400
CONNECT 16800
CONNECT 19200
CONNECT 21600
CONNECT 24000
CONNECT 26400
CONNECT 28800
CONNECT 31200
CONNECT 33600
10
11
32
12
30
31
33
34
35
36
37
38
95
97
A full list of response codes is provided in your SmartModem Reference Guide included on the NetComm CD
ROM.
YML391-3A
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
S Registers
Reg
0
1
2
3
4
5
6
7
Range
0-255
0-255
1-255
0-127
0-127
0-127
4-7
Def
00
00
43(+)
13
10
08
04
30
04
06
18
95
50
00
00
05
00
00
50
00
03
00
Unit
rings
rings
ASCII
ASCII
ASCII
ASCII
secs
secs
secs
0.1secs
0.1secs
msecs
0.02secs
Function
Rings Before Answer
Ring Count
Escape Sequence Character
Carriage Return Character
Line Feed Character
Backspace Character
Wait for Dial Tone
1-60
1-7
Wait for Carrier
8
9
Delay for Pause Modifier
Carrier Detect Response Time
Lost Carrier/Hang Up Delay
Touch Tone Timing
Escape Sequence Guard Time
Test in Progress (read only)
Test Timer
1-255
1-255
70-254
3-255
0-8
10
11
12
16
18
25
26
27
29
30
33
38
42
43
45
47
62
69
74
80
81
82
95
96
97
100
105
110
119
0-255
0-255
0-255
0-255
10-100
0-255
0-255
0-255
0-255
0-255
0-255
1-255
0-255
0-255
0-255
1-19
1-19
1-255
0-63
1-255
1-255
1-10
0-255
0-255
0-255
secs
0.01secs
0.01secs
secs
0.01secs
10secs
DTR Loss Detection Time
RTS-CTS Delay
Delay Before Security Dial-back
Hook Flash Duration (also sets S100)
Inactivity Timer (data mode)
EQM Threshold for V.32/V.32bis
Disconnect Delay
Modem Disconnect Reason
Break Sequence Length
EQM Threshold - V.22/V.22bis/212A
Auto-Range Time
secs
15
98
08
75
60
msecs
secs
0.01secs
secs
V.42 detection timer
Command line timeout
Modem Disconnect Reason (Previous Call)
Flow Control High Water Mark
Flow Control Low Water Mark
Failsafe Flow Control Overrun
Extended Result Codes
Help Page Width
15
03
60
0
80
24
5
30
4
0
5%
5%
bitmap
Help Page Length
100msecs
secs
rings
Hook Flash Duration (also sets S29)
Voice-mode ÒDead-manÓ timer
Voice-mode Rings before Answer
Power Down Feature
secs
Use AT? to see the Command Set supported by your modem's version of code.
YML391-3A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
Specifications
Dimensions
•
•
•
Height: 31mm
Length: 218mm
Width: 122mm
Communications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ITU-T 33600bps
ITU-T 31200bps
ITU-T V.34 (2400-33600bps)
ITU-T V.32bis (14400bps)
ITU-T V.32bis (1200bps)
ITU-T V.32 (9600bps)
ITU-T V.32 (7200bps)
ITU-T V.32 (4800bps)
ITU-T V.22bis (2400bps)
ITU-T V.22 (1200bps)
ITU-T V.23 (1200/75bps)
ITU-T V.21 (300bps)
Bell 212A (1200bps)
Bell 103 (300bps)
ITU-T V.17 (fax 12,000-14,400bps)
ITU-T V.29 (fax 7200-9600bps)
ITU-T V.27ter (fax 2400-4800bps)
Terminal Speeds
•
300bps - 230,400bps
Power
•
•
Plug Pack: 15VAC 6VA supplied
Will operate directly from 6.0 to 14.5 V DC
Caller ID
•
•
Austel TS 030
Bellcore MDMF message format
Command Sets
•
•
AT commands
EIA Class 1 &2 fax commands, V.25bis commands
Data Formats
•
•
Synchronous,
Asynchronous: 7/8 data bits
Flow Control
•
RTS/CTS, XON/XOFF and Transparent XON/XOFF (async mode only)
YML391-3A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial Modem User Guide
•
•
Error Correction
V.42, MNP 2-4, MNP10
Data Compression
•
V.42bis, MNP 5
Encryption
•
•
•
•
DES 64-bit Cypher Feedback (Aust only)
SuperSecure
Failsafe Feature
Hardware and firmware watchdog circuitry resets modem in the event of a lockup condition
Environmental
•
Operating: -10¡ to +50¡ C
Humidity
•
Up to 95% non-condensing
Build Options
•
•
9-38 V DC operation
HOST interface TTL levels via 20 way dual row pinstrip connector.
YML391-3A
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|