User Guide for
4xN 10/100/1000 Span iMatrix Switch™
Model ISW-CU3-S4x16
Doc. PUB ISWCU3S4U Rev. 1, 07/06
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Contents
Chapter 1
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 2
Installing the iMatrix Switch
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Configuring the iMatrix Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using the Command Line Interface (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting to Switch Span Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to the Monitoring Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Remote Interface Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daisy Chaining iMatrix Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3
Using iMatrix Switch Web Manager
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessing Web Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Viewing Switch Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switch Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Configuring the iMatrix Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Message Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 4
Using System Manager
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing System Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Exploring System Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Creating a Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Deleting a Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adding iMatrix Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Deleting an iMatrix Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Configuring an iMatrix Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Viewing iMatrix Switch Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Modifying an iMatrix Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Controlling Switch Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Entering Port Names and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appendix A
Specifications and Models
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix B
Command Line Interface
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Chapter 1
Introduction
Overview
Net Optics 4xN 10/100/1000 Span Port iMatrix Switches enhance LAN vis-
ibility by providing access across multiple 10/100/1000 Span ports for up to
four analyzers or security devices. The physical layer connections through the
iMatrix Switch eliminate the need to reconnect and reconfigure analyzers for
each new monitoring task. This flexibility instantly improves ease of use and
return on investment.
The 4xN 10/100/1000 Span iMatrix Switch supports simultaneous passive
monitoring of any four Span ports connected to the iMatrix Switch, each with
a separate distributed analyzer.
Scalable Deployment
Double or triple Span port coverage by daisy chaining iMatrix Switches. The
Daisy Chain option allows a single monitoring device or host PC to manage
up to three iMatrix Switches and 48 Span ports.
Remote Control
The iMatrix Switch Web Manager and System Manager allows you to remote-
ly set IP parameters and change which link is monitored with a click of your
mouse. The Web Manager is browser-based interface accessible from any PC
with a browser and access to the iMatrix Switch’s IP address. System Manager
is an SNMP-based management interface.
Reliability
For extra uptime protection, Net Optics iMatrix Switches offer redundant
power connections. Should the primary power source fail, the iMatrix Switch
automatically switches to the backup power source. Power LEDs on the front
of the iMatrix Switch indicate the current power source.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Key Features
Passive, Secure Technology
• Provides complete cross-link visibility at 1000 Mbps without data stream
interference or introducing a point of failure
• Daisy Chain iMatrix Switches for doubled or tripled coverage
• Redundant power ensures monitoring uptime
• Fully RoHS compliant
Ease of Use
• Remote management software provides control over which links are
being monitored
• LED indicators on the iMatrix Switch allow for quick status checks
• Front-mounted network connectors for easy installation and operation
• Flexible design with removable feet allows for either rack-mount or stand
alone use
• Tested and compatible with all major manufacturers’ monitoring devices,
including protocol analyzers, probes, and intrusion detection/prevention
systems
Support
• Net Optics offers free technical support throughout the lifetime of your
purchase. Our technical support team is available from 8 am to 5 pm Pacific
Time, Monday through Friday at +1 (408) 737-7777 and via email at
[email protected]. FAQs are also available on Net Optics website
2
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Unpacking and Inspection
Carefully unpack the 10/100/1000 Span Port iMatrix Switch and check for
damaged or missing parts. The iMatrix Switch ships with the following:
• 10/100/1000 Span Port iMatrix Switch
• Two power cords
• One RS232 cable
• Nine straight-through CAT5e cables
• Two Mini-DIN cables
• 10/100/1000 Span Port iMatrix Switch Quick Install Guide
• One software CD
• Pads for surface mounting
• Brackets and fasteners for rack mounting
You may have also ordered an extended warranty. Carefully check the pack-
ing slip against parts received. If any part is missing or damaged, contact Net
Optics' Customer Service immediately.
About this Guide
This Guide provides you all the information you need to configure and operate
the 10/100/1000 Span Port iMatrix Switch. Please read the entire Guide before
attempting to install or operate the iMatrix Switch.
This guide covers the following models:
Part Number
Description
ISW-CU3-S4X16
4x16 10/100/1000 Span Port iMatrix Switch
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Product Diagrams
Monitor Port LED Displays
Power LEDs
Span Port Connectors
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
Monitor
1
Daisy Chain
Monitor
2
Daisy Chain
Monitor
3
Daisy Chain
Monitor
4
Monitor Ports
Monitor Daisy Chain Ports
Figure 1: Front Panel ISW-CU3-S4X16
Power Plug
Power Plug
Remote Interface
Port
DIP Switch
CONTROL PORT
1
CONTROL PORT
2
1
2
3
4
5
6
7
8
O
F
F
Daisy Chain
Control Ports
Control Ports
Rubber Feet
(removable)
Rubber Feet
(removable)
Figure 2: Rear Panel
LED Indicators
Monitor Port LEDs: Each Monitor Port has a 2-character LED that shows
the number of the Span port currently connected to the monitor port.
Link/Activity Indicator: If a good link is established, the LED illuminates a
steady green. If there is current activity on this link, the LED flashes.
10/100/1000 Indicator: If the Port is set to 10 Mbps, the LED will illuminate
orange. If the Port is set to 100 Mbps, the LED will illuminate yellow. If the
Port is set to 1000 Mbps, the LED will illuminate green.
PWR 1/ PWR 2: Main and Redundant Power. If the Tap is deployed with
both power supplies, both LEDs illuminate when the Tap is connected to
power. An off power LED indicates that the corresponding power supply is
not functioning or not connected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Chapter 2
Installing the iMatrix Switch
Overview
The procedure for installing the iMatrix Switch follows these basic steps:
• Plan the installation
• Configure IP parameters
• Mount the iMatrix Switch
• Connect the Management Port
• Connect to the network
• Connect to the monitoring devices
• Apply power to the iMatrix Switch
• Check the installation
Installation Planning
There are two methods for connecting your iMatrix Switch:
Single iMatrix Switch Mode
• A single monitoring device to controls the Monitor Ports of a single
iMatrix Switch from one COM Port.
Daisy Chaining Mode
• Allows up to three iMatrix Switches to be controlled from one monitoring
device or host PC.
Remote Access
The remote access features require that you assign an IP address to the
iMatrix Switch. If you are daisy chaining iMatrix Switches, you only need an
IP address for the Controller iMatrix Switch. You may also wish to assign a
netmask.
If you plan to remotely control the iMatrix Switch over WAN, you can also set
a gateway and IP address where you plan to use the SNMP management tool.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Configuring the iMatrix Switch
The iMatrix Switch is configured with default values that allow you to install
the iMatrix Switch and then modify parameters from Web Manager or SNMP
Manager.
The defaults values are:
IP Address: 10.60.0.123
Netmask: 255.255.0.0
Monitor Ports 1-4: Gigabit
CLI username: netoptics
CLI password: netoptics
You can set all parameters, check status, and control Monitor Port connections
from the Command Line Interface. You can change most settings later from
one of the remote interfaces.
Using the Command Line Interface (CLI)
All configuration and control options are accessible from the iMatrix Switch's
Command Line Interface. You must set a new username and password, IP
address for the iMatrix Switch, and the port speeds. Other parameters are
optional and dependent on your installation.
For security reasons, some parameters can only be set with the CLI.
Use these commands to:
• Set CLI username and password
• Enable or disable the remote interfaces
• Turn character echo to the terminal emulation software on or off
If you wish to disable the Management Port and remote interfaces, you can do
so from the CLI using the Display command.
To access the iMatrix Switch CLI:
1. Make sure power to the iMatrix Switch is off.
2. Connect a PC with terminal emulation software, such as HyperTerminal,
to the iMatrix Switch Control Port 2 using the RS232 DB-9 cable supplied
with the iMatrix Switch.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
DB9 Control Port 2
CONTROL PORT
1
CONTROL PORT
2
1
2
3
4
5
6
7
8
O
F
F
To COM port on monitoring device or computer
Figure 9: Connecting to the CLI
3. Launch your terminal emulation software and set the communication
parameters to:
19200 baud
8 data bits
No parity
1 stop bit
No flow control
3. Connect power to the iMatrix Switch. The CLI banner and login prompt
appears.
*************************************
* Net Optics Command Line Interface *
*************************************
Login:
Password:
Figure 9: Login and Password Prompts
4. Type netoptics and press Enter.
5. At the password prompt, type netoptics and press Enter. The NetOp-
tics:prompt appear.
To change the username and password:
1. Change the username by typing the following command:
set username <username>
where <username> is your new username.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
2. Change the password by typing the following command:
set password <password>
where <password> is your new password.
3. Record the username and password in a secure location.
To set the iMatrix Switch IP address:
1. Type set ip <ip address> where <ip address> is the IP address you are
assigning to the iMatrix Switch and press Enter.
For example, typing set ip 10.60.0.100 sets the iMatrix Switch IP address
to 10.60.0.100.
To display current settings:
1. Type show set and press Enter. The CLI displays the current settings
similar to the example in Figure 10.
show set
IP Address:
Netmask:
Manager:
Gateway:
HW Version:
SW Version:
10.60.0.123
255.255.0.0
10.10.1.40
10.60.0.118
REV 1.00
REV 1.00
Port 1 Parameters: Gigabit
Port 2 Parameters: Gigabit
Port 3 Parameters: Gigabit
Port 4 Parameters: Gigabit
Figure 10: Show Set Command Example
To disable the remote interfaces:
1. Type show display and press Enter to view the current setting. The default
value is Display: ON.
2. Type display and press Enter. Access to the iMatrix Switch from remote
interfaces will be blocked.
3. To restore the display and remote interfaces, type display and press Enter.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
To use the Help command:
1. Type Help and press Enter at the NetOpticsprompt. The list of help
topics is displayed.
NetOptics: help
*************************************
* Net Optics Command Line Interface *
*************************************
Usage: “help”
<variable>:
set
- Configure various options.
reset - Reset options.
switch - Switch control commands.
show - show current configuration and
status.
echo - Turn on or off echoing of
characters.
display- Toggle to enable/disable network
- accessibility.
help - This help screen.
Figure 11: iMatrix Switch CLI Help Menu
5. To view the syntax for changing the iMatrix Switch’s configuration param-
eters, type help set and press Enter.
6. To view the syntax for other commands, type help followed by the com-
mand. For more information on CLI commands, see Appendix B.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Connecting to Switch Span Ports
1. Connect Span Port 1 of the iMatrix Switch to the appropriate Span port on
your switch using CAT5e straight-through cables.
2. Repeat Step 1 for each additional network switch Span port you wish to
monitor.
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
Monitor
1
Daisy Chain
Monitor
2
Daisy Chain
Monitor
3
Daisy Chain
Monitor
4
To switch Span Port
To switch Span Port
Figure 4: Connecting Span Ports
Connecting to the Monitoring Device
You need to connect the iMatrix Switch to the input ports (NICs) of the moni-
tor device and connect Control Port 2 to a COM port on the monitoring device
or computer where you access the CLI.
1. Verify that the DIP switch located on the rear of the unit is set as shown in
Figure 5 below.
/
.
1
2
3
4
5
6
7
8
Figure 5: DIP Switch Settings for Single iMatrix Switch (Controller)
Note:________________________________________________________________
DIP switches 3 through 8 must remain in the ON position.
______________________________________________________________________
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
2. Connect a CAT5e cable to the iMatrix Switch Monitor Port 1 and the input
port of the monitoring device.
3. Repeat Step 3 above to connect Monitor Ports 2 through 4 of the iMatrix
Switch to a monitoring device.
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
Monitor
1
Daisy Chain
Monitor
2
Daisy Chain
Monitor
3
Daisy Chain
Monitor
4
To monitoring device NIC 4
To monitoring device NIC 3
To monitoring device NIC 2
To monitoring device NIC 1
Figure 7: Connecting Monitor Ports
4. Supply power to the iMatrix Switch using the power cords included with
the unit. Verify that the Power LEDs illuminate.
Connecting the Remote Interface Port
In order to access the remote interfaces, you must connect the Remote Inter-
face Port to a network switch or hub as shown in Figure 8.
CONTROL PORT
1
CONTROL PORT
2
1
2
3
4
5
6
7
8
O
F
F
To network switch or hub
Figure 8: Connecting the Remote Interface Port
Note:________________________________________________________________
Access to the remote interface is controller by the Display command in the
CLI. To have access to the remote interfaces, make sure the Display option is
set to ON.
______________________________________________________________________
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Daisy Chaining iMatrix Switches
You have the option of connecting as many as three switches together for
control by a single monitoring device or computer. It does not matter if you
are connecting the monitoring ports to one device or separate devices.
In a daisy chain configuration, one iMatrix Switch serves as the Controller
to one or two Client iMatrix Switches. The Controller/Client relationship is
set with the DIP switches on the rear of the iMatrix Switch. iMatrix Switches
are set to function as a Controller by default. Network traffic is passed from
the Clients to the Controller and control is sent through the Controller to the
Clients.
The basic steps to daisy chaining iMatrix Switches are:
1. Connect the Controller iMatrix Switch as described in the previous
sections.
2. Connect the Controller and Client Control Ports
3. Connect the Controller and Client Monitor Ports
4. Connect the additional Span Ports
To daisy chain iMatrix Switches:
1. Configure and install the Controller iMatrix Switch as described in the
preceding sections.
2. Choose the iMatrix Switch you will use as Client 1 and set the DIP switch
positions (located on rear of unit) as shown in Figure 9. If you are install-
ing a third switch, set the DIP switch as shown in Figure 9 for Client 2.
3. Connect CAT5e cables between the Daisy Chain Ports of iMatrix Switch 1
and the Monitor Ports of iMatrix Switch 2. If you are connecting a third
iMatrix Switch, connect CAT5e cables between the Daisy Chain Ports of
iMatrix Switch 2 and the Monitor Ports of iMatrix Switch 3 (see Figure 9).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
M
1
Daisy Chain
r
2
Daisy Chain
M
3
Daisy Chain
M4
iMatrix Switch Client 2
Client 2 DIP Switch Settings
1
2
3
4
5
6
7
8
OFF
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
Mor
1
Daisy Chain
Mr
2
Daisy Chain
Mo
3
Daisy Chain
Mo4
iMatrix Switch Client 1
Client 1 DIP Switch Settings
1
2
3
4
5
6
7
8
OFF
1
2
3
4
9
10
11
12
2
1
4x16 10/100/1000 Span Port Switch
5
6
7
8
13
14
15
16
Daisy Chain
Monitor
1
Daisy Chain
Monitor
2
Daisy Chain
Monitor
3
Daisy Chain
Monitor
4
Controller iMatrix Switch
Master DIP Switch Settings
1
2
3
4
5
6
7
8
To monitoring device
To monitoring device
To monitoring device
To monitoring device
OFF
Figure 9: Connecting Daisy Chained Monitor Ports
4. Connect the supplied Mini-DIN cable between Daisy Chain Port OUT of
the Controller iMatrix Switch and Daisy Chain Port IN of iMatrix Switch
Client 1.
If you are installing a third iMatrix, connect the supplied Mini-DIN cable
between Daisy Chain Port OUT of iMatrix Switch 2 and Daisy Chain Port
IN of iMatrix Switch 3 (see Figure 10).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
CONTROL PORT
1
CONTROL PORT
2
1
2
3
4
5
6
7
8
O
F
F
CONTROL PORT
1
CONTROL PORT 2
1
2
3
4
5
6
7
8
O
F
F
CONTROL PORT
1
CONTROL PORT 2
1
2
3
4
5
6
7
8
O
F
F
Figure 10: Connecting the Daisy Chain Control Ports
5. Supply power to the iMatrix Switch using the power cords included with
the unit. Verify that the Power LEDs illuminate.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Chapter 3
Using iMatrix Switch Web Manager
Overview
This chapter describes how to monitor and control individual iMatrix Switches
using Web Manager. The following topics are covered:
• Accessing Web Manager
• Viewing iMatrix Switch Status
• Controlling iMatrix Switch Connections
• Configuring the iMatrix Switch
Web Manager is the browser-based interface that allows you to change configu-
ration settings, view status, and control which Span ports are connected to the
monitoring devices.
Note:____________________________________________________________________
To access Web Manager, the Display option in the CLI must be set to ON. For
more information, see Using the Command Line Interface on page 4.
__________________________________________________________________________
Accessing Web Manager
Web Manager is a browser-based interface that provides access to any iMatrix
Switch with an IP address accessible from the computer running Web Manager.
Web Manager supports all common browsers.
To access Web Manager:
1. Open an Internet browser on your computer.
2. Enter the iMatrix Switch’s IP address in the URL box and press Enter. The
default IP address is 10.60.0.123. The Web Manager page appears as shown in
Figure 11.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Figure 11: Web Manager Page
To save any changes to the iMatrix Switch, you must click Submit Changes. To
update the display, click your browser's refresh button.
Viewing Switch Status
You can view iMatrix Switch information from the Switch Status section of Web
Manager. The following table explains the status fields.
Field Name
Value
1 - 4
Description
Total Switches
Total Data Port
Indicates the number of switches configured
1 - 16
Display the total number of ports available for
this switch model or the total number of Span
ports available in a daisy-chain configuration.
Switch 1 Model
Switch 2 Model
Switch 3 Model
-
-
-
Displays the model of the switch
Displays the model of the switch
Displays the model of the switch
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Field Name
Value
Description
Switch Hardware
Version
Displays the hardware version of the switch
Switch Software
Version
Displays the software version of the switch
Switch Control
Web Manager lets you set which data port is connected to the Monitor Port. To
change the network link you are monitoring, enter the number of the data port for
the link and click Submit Changes.
To disconnect the Monitor Port from all data ports, select Yes from the Reset All
Switches drop-down menu and click Submit Changes.
Configuring the iMatrix Switch
Web Manager allows you to set the IP parameters for the switch. To change a set-
ting, enter the IP address in the text box and click Submit Changes. The following
table explains each available option.
Field Name
Function/Value Description
IP Address
0.0.0.0
0.0.0.0
IP address of the iMatrix Switch. The de-
fault IP address is 10.60.0.123. You can
change the IP address by typing a new IP
address in the text box.
Net Mask
Displays current Net Mask of the
iMatrix Switch. The default Net Mask is
255.255.0.0. You can change the Net
Mask by typing a new Net Mask in the
text box.
Manager IP
Address
0.0.0.0
0.0.0.0
IP address of the computer running
iMatrix System Manager over a WAN.
You can change the IP address by typing
a new IP address in the text box.
Gateway IP
Address
Displays the IP address of the current
WAN Gateway. You can change the
Gateway by typing a new IP address in
the text box.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span Port iMatrix Switch
Message Board
You can post a message about the iMatrix Switch in the Message Board text box.
Anyone who open Web Manager for this iMatrix Switch will see your message.
To enter a message, simple click in the text box and type your message.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Chapter 4
Using System Manager
Overview
This chapter describes how to install and use Net Optics' System Manager, which
allows you to change settings, view status, and retrieve data remotely from mul-
tiple Net Optics iMatrix Switch devices. The following topics are covered:
• Installing System Manager
• Exploring System Manager
• Creating a Group
• Adding and Deleting iMatrix Switches
• Using the Status Tab
• Using the Configuration Tab
Installing System Manager
The installation executable file for System Manager can be found on the CD
included with the iMatrix Switch.
To install System Manger:
1. Locate Setup.exe on the CD and double click it. The License Agreement dialog
box appears as shown in Figure 12.
Figure 12: Net Optics System Manager License Agreement
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
3. After reading the agreement, select I Agree and click Next to install System
Manager. The Welcome dialog box appears as shown in Figure 13.
Figure 13: Welcome Dialog Box
2. Click Next. The Select Installation Folder dialog box shown in Figure 14
appears.
Figure 14: Select Installation Folder
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
3. To install in the default folder, make no changes to the path in the Folder: text
box. To install in a different location, either type the path in the Folder: text
box or click Browse to find another location.
To check the space available for System Manager on the selected drive, click
Disk Cost.
4. To limit access to System Manager to the current user of the PC, select Just
Me. To allow access to any user logged into the PC, select Everyone.
5. Click Next. The Confirm Installation dialog box shown in Figure 15 appears.
To continue the installation, click Next. The Progress dialog box appears as
shown in Figure 16.
Figure 15: Confirm Installation
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Figure 16: Installation Progress
6. If you want to stop the installation, click Cancel. When the installation is com-
plete, the Installation Complete dialog box appears as shown in Figure 17.
Figure 17: Installation Complete
7. Click Close. System Manager is now installed on your computer and there is a
Net Optics shortcut icon on your desktop.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Exploring System Manager
This section explains the features and functions of System Manager. With System
Manager you can:
• Create iMatrix Switch groups
• Add and delete iMatrix Switches from the system
• Remotely configure iMatrix Switches
• View iMatrix Switch status information
• Connect Monitor Ports to Span Ports
• Add text information about the iMatrix Switch
NOTE ___________________________________________________________________
To access the iMatrix Switch with System Manager, the Display option in the CLI
must be set to ON. For more information, see Using the Command Line Interface
on page 4.
__________________________________________________________________________
To access System Manager:
1. Double click the System Manager icon on your PC desktop. The initial window,
shown in Figure 18, will not show any iMatrix Switches.
System Frame
Information Frame
Figure 18: Initial window
The System Frame displays iMatrix Switches and iMatrix Switch Groups as you
add them to the system. The Information Frame displays Status, Configuration
and Control information for individual iMatrix Switches.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Tip! _____________________________________________________________________
To use pop-up menu shortcuts, click your right mouse button in the System Frame.
__________________________________________________________________________
Using the Toolbar
Figure 19 shows the System Manager toolbar.
Figure 19: Toolbar
The table below describes the headings found on the toolbar.
Tool
Description
New Node
New Group
Delete
Add iMatrix Switches to a group
Create an iMatrix Switch group
Delete iMatrix Switch from System Manager
Modify
Change the iMatrix Switch name, IP address, model, and add
notes
Refresh
Exit
Refresh the data displayed in the Information Frame.
Close Net Optics System Manager
About
View information about System Manager
Creating a Group
You can organize iMatrix Switch devices into groups for quick access. You must
create a Group before you can add iMatrix Switches to your system.
To create an iMatrix Switch group:
1. Click New Group in the toolbar as shown in Figure 20. A new group bar
appears in the System Frame as shown in Figure 21.
Figure 20: New Group
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Figure 21: Group Bar
2. Type the name of the new group and press Enter.
Deleting a Group
You can delete a group however, all iMatrix Switches in that group will also be
deleted from System Manager.
Note:____________________________________________________________________
Deleting an iMatrix Switch from System Manager does not affect the current
operating status of the iMatrix Switch. It will continue to pass traffic from the Span
Ports connected at the time you delete the iMatrix Switch from System Manager to
the Monitor Ports.
__________________________________________________________________________
To delete a Group:
1. Right click on the group bar of the group you want to delete.
2. Select Delete from the pop-up menu. The Group and all associated iMatrix
Switches are deleted from System Manager.
Adding iMatrix Switches
To configure and control iMatrix Switches with System Manager, you must add
iMatrix Switches to System Manager. Once you have added an iMatrix Switch,
you can configure, modify, group, and delete it from System Manager.
Note:____________________________________________________________________
The iMatrix Switch must be connected to the network as described in Chapter 2
before it can be added to System Manager.
__________________________________________________________________________
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
To add an iMatrix Switch to the system:
1. Select the Group to which you want to add an iMatrix Switch by clicking the
group bar.
2. Click New Node in the toolbar as shown in Figure 22. The New Node dialog
box appears as shown in Figure 23.
Figure 22: Adding a New iMatrix Switch
Figure 23: New iMatrix Switch
2. Enter a name for the iMatrix Switch you are adding in the Node Name text
box. Each Node Name in the system must be unique.
3. Enter the IP address of the iMatrix Switch in the IPAddress text box. Make
sure the IP address is unique on the network.
4. Select your model of the iMatrix Switch from the Product drop-down list.
5. Enter any relevant information about the iMatrix Switch in the Notes text box.
6. Check your settings and click Create. The System Manger now shows the
iMatrix Switch in the system similar to Figure 24.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Figure 24: Net Optics System Manager with an iMatrix Switch
The indicator to the right of the iMatrix Switch picture blinks green when the
iMatrix Switch is functioning normally. If there is an alarm condition on the
iMatrix Switch, the indicator blinks red. If System Manager cannot communi-
cate with the iMatrix Switch, the graphic of the switch appears grayed. Check
that the iMatrix Switch is connected to the network and verify the configuration
information.
7. Repeat Steps 1-6 for each iMatrix Switch you are adding to System Manager.
Tip! _____________________________________________________________________
To change the order in which iMatrix Switches appear in the System Frame, click
and drag iMatrix Switches into the desired order.
__________________________________________________________________________
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Deleting an iMatrix Switch
You can delete an iMatrix Switch from System Manager when you remove an
iMatrix Switch from your network. If you have removed an iMatrix Switch from
the network, System Manager continues to poll the iMatrix Switch’s IP address for
data until you delete the iMatrix Switch from System Manager.
To delete an iMatrix Switch from System Manager:
1. Select the iMatrix Switch you want to delete by clicking its icon.
2. Click Delete in the toolbar. A confirmation dialog box appears.
Figure 25: Delete Confirmation
3. Click Yes to delete the iMatrix Switch from System Manager.
Configuring an iMatrix Switch
You can set configuration parameters of an iMatrix Switch in the system from the
Configure tab.
To configure the iMatrix Switch:
1. Click on the icon of the iMatrix Switch you want to configure and click the
Configure tab as shown in Figure 26.
Figure 26: iMatrix Switch Configure Tab
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
2. For the parameter you wish to configure, click on the corresponding value field.
3. Select an option from the drop-down list or enter a new value from your
keyboard.
4. The new configuration parameters take effect next time System Manager polls
the iMatrix Switch.
The table below describes the configuration options on the Configure Tab.
Host Name
The name of the iMatrix Switch
The IP address of the iMatrix Switch.
The IP address netmask.
IP Address
Netmask
Gateway IP Address
The IP address of the gateway.
System Manager IP
Address
The IP address of the host PC running System Manager
or third-party SNMP management tool.
Monitor Port 1
Parameter
The speed setting for Monitor Port 1 (GigaBit, 10 Mbps, or
100 Mbps).
Monitor Port 2
Parameter
The speed setting for Monitor Port 2 (GigaBit, 10 Mbps, or
100 Mbps).
Monitor Port 3
Parameter
The speed setting for Monitor Port 3 (GigaBit, 10 Mbps, or
100 Mbps).
Monitor Port 4
Parameter
The speed setting for Monitor Port 4 (GigaBit, 10 Mbps, or
100 Mbps).
Viewing iMatrix Switch Information
System Manager allows you to view the current iMatrix Switch configuration
information, including the Monitor Port connections.
To view iMatrix Switch information:
1. Click the image of the iMatrix Switch you want to view in the System Frame. A
window similar to Figure 27 appears.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Figure 27: iMatrix Switch Status Tab
The Status tab is a read-only list of information from the iMatrix Switch. Use the
scroll bar and arrows to view the entire list if necessary.
TIP! _____________________________________________________________________
Fields that have been updated since the last refresh appear with a circle and arrow
just to the left of the value field.
__________________________________________________________________________
The following table explains the status fields.
Switch 1 Model
Switch 2 Model
Switch 3 Model
Hardware Version
Model of the Controller iMatrix Switch.
Model of the first Client iMatrix Switch, if present.
Model of the second Client iMatrix Switch, if present.
Hardware version of the Controller iMatrix Switch. The hard-
ware version is not displayed for Client iMatrix Switches.
Software Version
Software version of the Controller iMatrix Switch. The soft-
ware version is not displayed for Client iMatrix Switches.
Monitor Port 1
Data Port
The Span Port currently connected to Monitor Port 1. To
change the Monitor Port connection, use the Control Tab.
Monitor Port 2
Data Port
The Span Port currently connected to Monitor Port 2. To
change the Monitor Port connection, use the Control Tab.
Monitor Port 3
Data Port
The Span Port currently connected to Monitor Port 3. To
change the Monitor Port connection, use the Control Tab.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Monitor Port 4
Data Port
The Span Port currently connected to Monitor Port 4. To
change the Monitor Port connection, use the Control Tab.
Total Data Ports
Total number of Data Ports on the iMatrix Switch including
any ports on daisy-chained Client iMatrix Switches.
Total Switches
Total number of daisy-chained Client iMatrix Switches plus
the Controller iMatrix Switch (1-3).
Modifying an iMatrix Switch
You can change the IP address and other basic iMatrix Switch configuration
parameters from the Modify iMatrix Switch dialog box.
To modify the iMatrix Switch configuration:
1. In the System Frame, click on the image of the iMatrix Switch you want to
change.
2. Click Modify in the toolbar. The Modify Node dialog box appears as shown in
Figure 28.
Figure 28: Modify iMatrix Switch
3. Make the desired changes and click Save Change.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Controlling Switch Connections
Use the Control Tab to connect the Monitor Ports to a connected Span Port. You
can connect four monitoring devices to any four Span Ports on the switch or
daisy-chained switches.
To connect a Monitor Port to a Span Port:
1. Click the Control tab. Figure 29 shows the Control Tab for a 2xN iMatrix
Switch. The 4xN GigaBit Copper Span Switch will show four Monitor Port
columns.
Figure 29: Control Tab
2. Click a port in the Mon. 1 column to connect the device on Monitor Port 1
to a Span Port. The example in Figure 30 shows Monitor Port 1 connected to
Span Port 2.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Figure 30: Connecting Monitor Port 1
2. Click a port in the Mon. 2 column to connect the device on Monitor Port 2 to a
Span Port. The example in Figure 31 shows Monitor Port 2 connected to Span
Port 4.
Figure 31: Connecting Monitor Port 2
3. Repeat for Steps 1 and 2 for Mon. 3 and Mon. 4 columns. You cannot connect
more than one Monitor Port to a Span Port.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
4. To clear all port connections, click Reset All.
Entering Port Names and Notes
You have the option of naming the Span Ports and entering a note. Naming the
Span Ports will make switch management easier. Add notes to the Span Port con-
nection to communicate important information to other users of System Manager.
To enter Span Port Names and Notes:
1. Click the text box next to the Span Port number you wish to name.
2. Enter the name of the Span Port and press Enter.
3. Click the text box in the Note column to add a note about this Span Port.
4. You can also enter a message about this particular switch in the Message Board
text box at the bottom of the page.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Appendix A
Specifications and Models
Specifications
Electrical
Power Input
100-240VAC, 0.5A, 47-63Hz
Environmental
Operating Temperature
0˚C to 55˚C
Storage Temperature
-10˚C to 70˚C
Relative Humidity
5% min, 95% max, non-condensing
Mechanical
Dimensions
1.75” high x 15.75” deep x 17” wide
Cable Interfaces:
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5e
Link Distance Supported: 90 meters (includes network and monitor
segments)
Connectors:
(4) RJ45, 8-pin connectors (monitor ports)
(4) RJ45, 8-pin connectors (monitor daisy chain ports)
(16) RJ45, 8-pin connectors (Span ports)
(2) Mini-DIN, 4-pin connectors (daisy-chain control
(2) DB9 serial control interfaces
Indicators
(4) 2-character LED
(20) Link/Activity LEDs
(2) Power LEDS
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Software
Command Line Interface
Any terminal emulation software
iMatrix Web Manager
Any browser
iMatrix System Manager
Windows 98, Windows 2000, Windows XP
Certifications
Fully RoHS compliant
36
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Appendix B
Command Line Interface
Command Sub-Command Syntax
Description
Help
Set
help set
Displays the set command
options.
Reset
Show
Echo
help reset
help show
help echo
help display
Displays the reset command
options.
Displays the show command
options.
Displays the echo command
options.
Display
IP
Displays the display command
options.
Set
set ip <address> Where <address> is the IP
address of the iMatrix Switch.
Netmask
Gateway
set netmask
<address>
Where <address> is the IP
address of the netmask.
set gateway
<address>
Where <address> is the IP
address of the gateway.
Manager
set manager
<address>
Where <address> is the IP
address of the remote man-
ager.
Parameter Port set parameter
port <port ID>
Where <port ID> is 1, 2, 3, or 4
and <parameter> is
0 = GigaBit
<parameter>
1 = 10 Mbps
2 = 100 Mbps
3 = 1000 Mbps
Username
Password
set username
<username>
Where <username> is the
authorized user's name, 9
characters or less.
set password
<password>
Where <password> is the
authorized user's password, 9
characters or less.
Reset
Storage
Switch
reset storage
reset switch
Resets configuation to factory
defaults.
Disconnects all Monitor Ports
from any data ports.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Description
Command Sub-Command Syntax
Switch
Monitor
Port
switch monitor
<monitor> port
<port ID>
Sets which data port is moni-
tored where <monitor> is 1,
2, 3, or 4 and <port ID> is the
data port number
Show
Set
show set
Displays currents settings.
Switch
show status
Displays current data port con-
nected to the monitor port.
Display
show display
Displays the display setting.
Display OFF disables remote
interfaces.
User
n/a
show user
Displays current user logged
into the CLI.
Echo
echo <on/off>
Echo off stops typed character
from being displayed on the
screen.
Display
n/a
display
Toggles the remote interface
on and off.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4xN 10/100/1000 Span iMatrix Switch
Notes:
39
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2006 by Net Optics, Inc. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|