Important Information
Warranty
The PCI-6110E/6111E boards are warranted against defects in materials and workmanship for a period of one year
from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option,
repair or replace equipment that proves to be defective during the warranty period. This warranty includes parts and
labor.
The media on which you receive National Instruments software are warranted not to fail to execute programming
instructions, due to defects in materials and workmanship, for a period of 90 days from date of shipment, as evidenced
by receipts or other documentation. National Instruments will, at its option, repair or replace software media that do
not execute programming instructions if National Instruments receives notice of such defects during the warranty
period. National Instruments does not warrant that the operation of the software shall be uninterrupted or error free.
A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside
of the package before any equipment will be accepted for warranty work. National Instruments will pay the shipping
costs of returning to the owner parts which are covered by warranty.
National Instruments believes that the information in this manual is accurate. The document has been carefully
reviewed for technical accuracy. In the event that technical or typographical errors exist, National Instruments reserves
the right to make changes to subsequent editions of this document without prior notice to holders of this edition. The
reader should consult National Instruments if errors are suspected. In no event shall National Instruments be liable for
any damages arising out of or related to this document or the information contained in it.
EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND
SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
CUSTOMER’S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL
INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS
WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the liability of National
Instruments will apply regardless of the form of action, whether in contract or tort, including negligence. Any action
against National Instruments must be brought within one year after the cause of action accrues. National Instruments
shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided
herein does not cover damages, defects, malfunctions, or service failures caused by owner’s failure to follow the
National Instruments installation, operation, or maintenance instructions; owner’s modification of the product;
owner’s abuse, misuse, or negligent acts; and power failure or surges, fire, flood, accident, actions of third parties,
or other events outside reasonable control.
Copyright
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical,
including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part,
without the prior written consent of National Instruments Corporation.
Trademarks
ComponentWorks™, CVI™, DAQ-STC™, LabVIEW™, Measure™, MITE™, NI-DAQ™, NI-PGIA™, RTSI™,
SCXI™, and VirtualBench™ are trademarks of National Instruments Corporation.
Product and company names listed are trademarks or trade names of their respective companies.
WARNING REGARDING MEDICAL AND CLINICAL USE OF NATIONAL INSTRUMENTS PRODUCTS
National Instruments products are not designed with components and testing intended to ensure a level of reliability
suitable for use in treatment and diagnosis of humans. Applications of National Instruments products involving
medical or clinical treatment can create a potential for accidental injury caused by product failure, or by errors on the
part of the user or application designer. Any use or application of National Instruments products for or involving
medical or clinical treatment must be performed by properly trained and qualified medical personnel, and all traditional
medical safeguards, equipment, and procedures that are appropriate in the particular situation to prevent serious injury
or death should always continue to be used when National Instruments products are being used. National Instruments
products are NOT intended to be a substitute for any form of established process, procedure, or equipment used to
monitor or safeguard human health and safety in medical or clinical treatment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table
of
Organization of This Manual........................................................................................xi
Conventions Used in This Manual................................................................................xii
National Instruments Documentation ...........................................................................xiii
Related Documentation.................................................................................................xiv
Customer Communication ............................................................................................xiv
Chapter 1
About the 611X E Boards .............................................................................................1-1
What You Need to Get Started .....................................................................................1-2
Software Programming Choices ...................................................................................1-2
National Instruments Application Software...................................................1-2
NI-DAQ Driver Software...............................................................................1-3
Register-Level Programming .........................................................................1-4
Optional Equipment......................................................................................................1-5
Custom Cabling ............................................................................................................1-5
Unpacking.....................................................................................................................1-6
Chapter 2
Software Installation.....................................................................................................2-1
Hardware Installation....................................................................................................2-1
Board Configuration .....................................................................................................2-2
Chapter 3
Analog Input .................................................................................................................3-2
Input Mode .....................................................................................................3-2
Input Polarity and Input Range.......................................................................3-3
Considerations for Selecting Input Ranges......................................3-4
Input Coupling................................................................................................3-4
Dither..............................................................................................................3-4
© National Instruments Corporation
v
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Analog Trigger ............................................................................................................. 3-6
Timing Signal Routing ................................................................................................. 3-11
Programmable Function Inputs...................................................................... 3-12
Chapter 4
I/O Connector............................................................................................................... 4-1
Analog Input Signal Connections................................................................................. 4-8
Types of Signal Sources............................................................................................... 4-9
Floating Signal Sources ................................................................................. 4-9
Ground-Referenced Signal Sources............................................................... 4-9
Differential Connection Considerations......................................................... 4-10
Analog Output Signal Connections.............................................................................. 4-13
TRIG1 Signal................................................................................... 4-19
TRIG2 Signal................................................................................... 4-20
AIGATE Signal ............................................................................... 4-25
SISOURCE Signal........................................................................... 4-25
Waveform Generation Timing Connections.................................................. 4-26
WFTRIG Signal............................................................................... 4-26
UPDATE* Signal ............................................................................ 4-27
UISOURCE Signal.......................................................................... 4-28
PCI-6110E/6111E User Manual
vi
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
GPCTR1_SOURCE Signal..............................................................4-32
GPCTR1_OUT Signal .....................................................................4-33
GPCTR1_UP_DOWN Signal..........................................................4-34
Field Wiring Considerations.........................................................................................4-35
Chapter 5
Loading Calibration Constants .....................................................................................5-1
Self-Calibration.............................................................................................................5-2
External Calibration......................................................................................................5-2
Customer Communication
Glossary
Index
© National Instruments Corporation
vii
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Figures
Figure 3-1. PCI-6110E Block Diagram ................................................................... 3-1
Figure 3-2. PCI-6111E Block Diagram ................................................................... 3-2
Figure 3-3. Effects of Dither on Signal Acquisition ................................................ 3-5
Figure 3-7. Above-High-Level Analog Triggering Mode ....................................... 3-8
Figure 3-8. Inside-Region Analog Triggering Mode ............................................... 3-8
Figure 3-11. CONVERT* Signal Routing................................................................. 3-11
Figure 3-12. RTSI Bus Signal Connection ................................................................ 3-13
Figure 4-2. 611X E Board PGIA.............................................................................. 4-8
Figure 4-5. Analog Output Connections .................................................................. 4-13
Figure 4-6. Digital I/O Connections......................................................................... 4-14
Figure 4-7. Timing I/O Connections........................................................................ 4-16
Figure 4-8. Typical Posttriggered Acquisition......................................................... 4-17
Figure 4-9. Typical Pretriggered Acquisition .......................................................... 4-18
Figure 4-10. SCANCLK Signal Timing .................................................................... 4-18
Figure 4-11. EXTSTROBE* Signal Timing.............................................................. 4-19
Figure 4-12. TRIG1 Input Signal Timing .................................................................. 4-20
Figure 4-13. TRIG1 Output Signal Timing................................................................ 4-20
Figure 4-14. TRIG2 Input Signal Timing .................................................................. 4-21
Figure 4-15. TRIG2 Output Signal Timing................................................................ 4-21
Figure 4-16. STARTSCAN Input Signal Timing ...................................................... 4-22
Figure 4-17. STARTSCAN Output Signal Timing.................................................... 4-23
Figure 4-18. CONVERT* Input Signal Timing......................................................... 4-24
Figure 4-19. CONVERT* Output Signal Timing...................................................... 4-24
Figure 4-20. SISOURCE Signal Timing.................................................................... 4-26
Figure 4-21. WFTRIG Input Signal Timing .............................................................. 4-27
Figure 4-22. WFTRIG Output Signal Timing............................................................ 4-27
Figure 4-23. UPDATE* Input Signal Timing............................................................ 4-28
Figure 4-24. UPDATE* Output Signal Timing ......................................................... 4-28
Figure 4-25. UISOURCE Signal Timing................................................................... 4-29
Figure 4-26. GPCTR0_SOURCE Signal Timing ...................................................... 4-30
PCI-6110E/6111E User Manual
viii
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-27. GPCTR0_GATE Signal Timing in Edge-Detection Mode ...................4-31
Figure 4-28. GPCTR0_OUT Signal Timing ..............................................................4-31
Figure 4-29. GPCTR1_SOURCE Signal Timing.......................................................4-32
Figure 4-30. GPCTR1_GATE Signal Timing in Edge-Detection Mode ...................4-33
Figure 4-31. GPCTR1_OUT Signal Timing ..............................................................4-33
Figure 4-32. GPCTR Timing Summary .....................................................................4-34
Figure B-1. 68-Pin 611X E Series Connector Pin Assignments ...............................B-2
Tables
Table 3-1.
Actual Range and Measurement Precision ............................................3-3
Table 4-1.
Table 4-2.
Table 4-3.
Signal Descriptions for I/O Connector Pins .........................................4-3
I/O Signal Summary for the 611X E .....................................................4-6
Signal Source Types ..............................................................................4-10
© National Instruments Corporation
ix
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About
This
Manual
This manual describes the electrical and mechanical aspects of the
611X E family of boards and contains information concerning their
operation and programming.
The 611X E family of boards includes:
•
•
PCI-6110E
PCI-6111E
Your 611X E board is a high-performance multifunction analog, digital,
and timing I/O board for PCI bus computers. Supported functions
Organization of This Manual
The PCI-6110E/6111E User Manual is organized as follows:
•
you need to get started, describes the optional software and optional
•
•
•
Chapter 2, Installation and Configuration, explains how to install
and configure your 611X E board.
hardware functions on your 611X E board.
output signal connections to your 611X E board via the board I/O
connector.
•
•
•
Chapter 5, Calibration, discusses the calibration procedures for
your 611X E board.
Appendix A, Specifications, lists the specifications of your 611X E
board.
connectors on your 611X E board.
© National Instruments Corporation
xi
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
•
•
•
•
Appendix C, Common Questions, contains a list of commonly
asked questions and their answers relating to usage and special
features of your 611X E board.
Appendix D, Customer Communication, contains forms you can
our products.
The Glossary contains an alphabetical list and description of terms
used in this manual, including acronyms, abbreviations, definitions
metric prefixes, mnemonics, and symbols.
The Index alphabetically lists topics covered in this manual,
including the page where you can find the topic.
Conventions Used in This Manual
The following conventions are used in this manual.
<>
Angle brackets enclose the name of a key on the keyboard (for example,
<option>). Angle brackets containing numbers separated by an ellipsis
represent a range of values associated with a bit or signal name
(for example, DIO<3..0>).
611X E
This refers to either the PCI-6110E or PCI-6111E board.
This icon to the left of bold italicized text denotes a note, which alerts
you to important information.
This icon to the left of bold italicized text denotes a caution, which
advises you of precautions to take to avoid injury, data loss, or a
system crash.
!
bold
Bold text denotes the names of menus, menu items, parameters, dialog
boxes, dialog box buttons or options, icons, windows, Windows 95 tabs,
or LEDs.
bold italic
Bold italic text denotes a note, caution, or warning.
italic
Italic text denotes emphasis, a cross reference, or an introduction to a
key concept. This font also denotes text from which you supply the
appropriate word or value, as in Windows 3.x.
Macintosh
Macintosh refers to all Macintosh OS computers with PCI bus, unless
otherwise noted.
PCI-6110E/6111E User Manual
xii
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
monospace
Text in this font denotes text or characters that you should literally enter
from the keyboard, sections of code, programming examples, and
syntax examples. This font also is used for the proper names of disk
drives, paths, directories, programs, subprograms, subroutines, device
names, functions, operations, variables, filenames, and extensions, and
for statements and comments taken from program code.
NI-DAQ
PC
NI-DAQ refers to the NI-DAQ driver software for Macintosh or
PC compatible computers unless otherwise noted.
Refers to all PC AT series computers with PCI bus unless otherwise
noted.
SCXI
SCXI stands for Signal Conditioning eXentsions for Instrumentation
and is a National Instruments product line designed to perform
front-end signal conditioning for National instruments plug-in DAQ
boards.
National Instruments Documentation
The PCI-6110E/6111E User Manual is one piece of the documentation
set for your DAQ system. You could have any of several types of
documentation depending on the hardware and software in your system.
Use the documentation you have as follows:
•
•
•
Getting Started with SCXI—If you are using SCXI, this is the first
manual you should read. It gives an overview of the SCXI system
and contains the most commonly needed information for the
modules, chassis, and software.
Your SCXI hardware user manuals—If you are using SCXI, read
these manuals next for detailed information about signal
connections and module configuration. They also explain in greater
detail how the module works and contain application hints.
Your DAQ hardware documentation—This documentation has
detailed information about the DAQ hardware that plugs into or is
connected to your computer. Use this documentation for hardware
installation and configuration instructions, specification
information about your DAQ hardware, and application hints.
•
Software documentation—You may have both application software
and NI-DAQ software documentation. National Instruments
application software includes ComponentWorks, LabVIEW,
LabWindows/CVI, Measure, and VirtualBench. After you set up
your hardware system, use either your application software
© National Instruments Corporation
xiii
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
documentation or the NI-DAQ documentation to help you write
your application. If you have a large, complicated system, it is
worthwhile to look through the software documentation before you
configure your hardware.
•
•
Accessory installation guides or manuals—If you are using
accessory products, read the terminal block and cable assembly
installation guides. They explain how to physically connect the
relevant pieces of the system. Consult these guides when you are
making your connections.
SCXI chassis manuals—If you are using SCXI, read these manuals
for maintenance information on the chassis and installation
instructions.
Related Documentation
The following documents contain information you may find helpful:
•
DAQ-STC Technical Reference Manual
•
National Instruments Application Note 025, Field Wiring and Noise
Considerations for Analog Signals
•
PCI Local Bus Specification Revision 2.0
Customer Communication
National Instruments wants to receive your comments on our products
and manuals. We are interested in the applications you develop with our
products, and we want to help if you have problems with them. To make
it easy for you to contact us, this manual contains comment and
configuration forms for you to complete. These forms are in
Appendix D, Customer Communication, at the end of this manual.
PCI-6110E/6111E User Manual
xiv
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1
Introduction
This chapter describes your 611X E board, lists what you need to get
started, describes the optional software and optional equipment, and
explains how to unpack your 611X E board.
About the 611X E Boards
Thank you for buying a National Instruments PCI-6110E/6111E
board. Your 611X E board is a completely Plug and Play, multifunction
analog, digital, and timing I/O board for PCI bus computers. The
611X E board features a 12-bit ADC per channel with four or two
simultaneously sampling analog inputs, 16-bit DACs with voltage
outputs, eight lines of TTL-compatible digital I/O, and two 24-bit
counter/timers for timing I/O. Because the 611X E board has no DIP
switches, jumpers, or potentiometers, it is easily software-configured
and calibrated.
The 611X E board is a completely switchless and jumperless data
acquisition (DAQ) board for the PCI bus. This feature is made possible
by the National Instruments MITE bus interface chip that connects the
board to the PCI I/O bus. The MITE implements the PCI Local Bus
Specification so that the interrupts and base memory addresses are all
software configured.
The 611X E board uses the National Instruments DAQ-STC system
timing controller for time-related functions. The DAQ-STC consists
of three timing groups that control analog input, analog output, and
general-purpose counter/timer functions. These groups include a total
of seven 24-bit and three 16-bit counters and a maximum timing
resolution of 50 ns. The DAQ-STC makes possible such applications as
buffered pulse generation, equivalent time sampling, and seamlessly
changing the sampling rate.
Often with DAQ boards, you cannot easily synchronize several
measurement functions to a common trigger or timing event. The
611X E board has the Real-Time System Integration (RTSI) bus to
solve this problem. The RTSI bus consists of our RTSI bus interface
© National Instruments Corporation
1-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
and a ribbon cable to route timing and trigger signals between several
functions on as many as five DAQ boards in your computer.
Detailed specifications of the 611X E board are in Appendix A,
Specifications.
What You Need to Get Started
To set up and use the 611X E board, you will need the following:
❑ Either the PCI-6110E or PCI-6111E board
❑ PCI-6110E/6111E User Manual
❑ One of the following software packages and documentation:
ComponentWorks
LabVIEW for Macintosh
LabVIEW for Windows
LabWindows/CVI for Windows
Measure
NI-DAQ for PC Compatibles
VirtualBench
❑ Your computer
Software Programming Choices
You have several options to choose from when programming your
National Instruments DAQ and SCXI hardware. You can use National
Instruments application software, NI-DAQ, or register-level
programming.
National Instruments Application Software
ComponentWorks contains tools for data acquisition and instrument
control built on NI-DAQ driver software. ComponentWorks provides
a higher-level programming interface for building virtual instruments
through standard OLE controls and DLLs. With ComponentWorks, you
can use all of the configuration tools, resource management utilities,
and interactive control utilities included with NI-DAQ.
LabVIEW features interactive graphics, a state-of-the-art user
interface, and a powerful graphical programming language. The
PCI-6110E/6111E User Manual
1-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
LabVIEW Data Acquisition VI Library, a series of VIs for using
LabVIEW with National Instruments DAQ hardware, is included with
LabVIEW. The LabVIEW Data Acquisition VI Library is functionally
equivalent to NI-DAQ software.
LabWindows/CVI features interactive graphics, state-of-the-art user
interface, and uses the ANSI standard C programming language. The
LabWindows/CVI Data Acquisition Library, a series of functions for
using LabWindows/CVI with National Instruments DAQ hardware, is
included with the NI-DAQ software kit. The LabWindows/CVI Data
Acquisition Library is functionally equivalent to the NI-DAQ software.
VirtualBench features virtual instruments that combine DAQ products,
software, and your computer to create a stand-alone instrument with the
added benefit of the processing, display, and storage capabilities of
your computer. VirtualBench instruments load and save waveform data
to disk in the same forms that can be used in popular spreadsheet
programs and word processors.
Using ComponentWorks, LabVIEW, LabWindows/CVI, or
VirtualBench software will greatly reduce the development time
for your data acquisition and control application.
NI-DAQ Driver Software
The NI-DAQ driver software is included at no charge with all National
Instruments DAQ hardware. NI-DAQ is not packaged with SCXI or
accessory products, except for the SCXI-1200. NI-DAQ has an
extensive library of functions that you can call from your application
programming environment. These functions include routines for analog
input (A/D conversion), buffered data acquisition (high-speed A/D
conversion), analog output (D/A conversion), waveform generation
(timed D/A conversion), digital I/O, counter/timer operations, SCXI,
RTSI, self-calibration, messaging, and acquiring data to extended
memory.
NI-DAQ has both high-level DAQ I/O functions for maximum ease of
use and low-level DAQ I/O functions for maximum flexibility and
performance. Examples of high-level functions are streaming data to
disk or acquiring a certain number of data points. An example of a
low-level function is writing directly to registers on the DAQ device.
NI-DAQ does not sacrifice the performance of National Instruments
DAQ devices because it lets multiple devices operate at their peak.
© National Instruments Corporation
1-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
NI-DAQ also internally addresses many of the complex issues between
the computer and the DAQ hardware such as programming interrupts
and DMA controllers. NI-DAQ maintains a consistent software
interface among its different versions so that you can change platforms
with minimal modifications to your code. Whether you are using
conventional programming languages or National Instruments
application software, your application uses the NI-DAQ driver
software, as illustrated in Figure 1-1.
ComponentWorks,
Conventional
LabVIEW,
Programming
LabWindows/CVI,
Environment
or VirtualBench
NI-DAQ
Driver Software
DAQ or
SCXI Hardware
Personal Computer
or Workstation
Figure 1-1. The Relationship between the Programming Environment,
NI-DAQ, and Your Hardware
Register-Level Programming
The final option for programming any National Instruments DAQ
hardware is to write register-level software. Writing register-level
programming software can be very time-consuming and inefficient,
and is not recommended for most users.
Even if you are an experienced register-level programmer, using
NI-DAQ or application software to program your National Instruments
DAQ hardware is easier than, and as flexible as, register-level
programming, and can save weeks of development time.
PCI-6110E/6111E User Manual
1-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Optional Equipment
National Instruments offers a variety of products to use with the 611X E
board, including cables, connector blocks, and other accessories, as
follows:
•
•
Cables and cable assemblies
Connector blocks, shielded and unshielded 50- and 68-pin screw
terminals
•
•
RTSI bus cables
Low channel-count signal conditioning modules, boards, and
accessories, including conditioning for strain gauges, RTDs,
and relays
For more specific information about these products, refer to your
National Instruments catalogue or call the office nearest you.
Custom Cabling
National Instruments offers cables and accessories for you to prototype
your application or to use if you frequently change board
interconnections.
If you want to develop your own cable, however, the following
guidelines may be useful:
•
For the analog input signals, shielded twisted-pair wires for each
analog input pair yield the best results, assuming that you use
differential inputs. Tie the shield for each signal pair to the ground
reference at the source.
•
•
Route the analog lines separately from the digital lines.
When using a cable shield, use separate shields for the analog and
digital halves of the cable. Failure to do so results in noise coupling
into the analog signals from transient digital signals.
Mating connectors and a backshell kit for making custom 68-pin cables
are available from National Instruments.
© National Instruments Corporation
1-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
The following list gives recommended part numbers for connectors that
mate to the I/O connector on the 611X E board:
•
Honda 68-position, solder cup, female connector
(part number PCS-E68FS)
•
Honda backshell (part number PCS-E68LKPA)
Unpacking
The 611X E board is shipped in an antistatic package to prevent
electrostatic damage to the board. Electrostatic discharge can damage
several components on the board. To avoid such damage in handling
the board, take the following precautions:
•
•
•
Ground yourself via a grounding strap or by holding a grounded
object.
Touch the antistatic package to a metal part of your computer
chassis before removing the board from the package.
Remove the board from the package and inspect the board for
loose components or any other sign of damage. Notify National
Instruments if the board appears damaged in any way. Do not
install a damaged board into your computer.
•
Never touch the exposed pins of connectors.
PCI-6110E/6111E User Manual
1-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Installation and
Configuration
2
This chapter explains how to install and configure your 611X E board.
Software Installation
Install your software before you install the 611X E board. Refer to the
appropriate release notes indicated below for specific instructions on
the software installation sequence.
If you are using LabVIEW, LabWindows/CVI, or other National
Instruments application software packages, refer to the appropriate
release notes. After you have installed your application software, refer
to your NI-DAQ release notes and follow the instructions given there
for your operating system and application software package.
If you are using NI-DAQ, refer to your NI-DAQ release notes. Find
the installation section for your operating system and follow the
instructions given there.
Hardware Installation
You can install the 611X E board in any available expansion slot in your
hardware. The following are general installation instructions, but
consult your computer user manual or technical reference manual for
specific instructions and warnings.
1. Write down the 611X E board serial number in the
PCI-6110E/6111E Hardware and Software Configuration Form in
Appendix D, Customer Communication, of this manual.
2. Turn off and unplug your computer.
4. Remove the expansion slot cover on the back panel of the
computer.
© National Instruments Corporation
2-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Installation and Configuration
5. Insert the 611X E board into a 5 V PCI slot. Gently rock the board
to ease it into place. It may be a tight fit, but do not force the board
into place.
6. If required, screw the mounting bracket of the 611X E board to the
back panel rail of the computer.
7. Replace the cover.
8. Plug in and turn on your computer.
The 611X E board is installed. You are now ready to configure your
software. Refer to your software documentation for configuration
instructions.
Board Configuration
Due to the National Instruments standard architecture for data
acquisition and the PCI bus specification, the 611X E board
is completely software configurable. You must perform two types
of configuration on the 611X E board—bus-related and data
acquisition-related configuration.
The 611X E board is fully compatible with the industry standard
PCI Local Bus Specification Revision 2.0. This allows the PCI system to
automatically perform all bus-related configurations and requires no
user interaction. Bus-related configuration includes setting the board
base memory address and interrupt channel.
Data acquisition-related configuration includes such settings as analog
input coupling and range, and others. You can modify these settings
using NI-DAQ or application level software, such as ComponentWorks,
LabVIEW, LabWindows/CVI, and VirtualBench.
PCI-6110E/6111E User Manual
2-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Hardware Overview
This chapter presents an overview of the hardware functions on your
611X E board. Figure 3-1 shows a block diagram for the
PCI-6110E board.
CH0+
+
AI CH0
Mux
12
12
12
12
CH0
Latch
CH0
Amplifier
–
CH0
12-Bit ADC
Data (16)
Data (16)
Data (16)
CH0-
CH1+
+
AI CH1
Mux
CH1
Latch
CH1
Amplifier
–
CH1
12-Bit ADC
CH1-
CH2+
+
AI CH2
Mux
CH2
Latch
CH2
Amplifier
–
CH2
12-Bit ADC
Control
CH2-
Generic
Bus
Interface
PCI
Bus
Interface
Mini
MITE
ADC
FIFO
Data (32)
CH3+
+
Address/Data
AI CH3
Mux
CH3
Latch
CH3
Amplifier
–
CH3
12-Bit ADC
Data (16)
AI Control
CH3-
Calibration
Mux
EEPROM
IRQ
DMA
Analog
Trigger
Circuitry
2
Trigger
Trigger Level
DACs
Analog Input
Timing/Control
DMA/IRQ
Trigger
PFI / Trigger
Analog
EEPROM
DMA
Input
Control Interface
Control
Bus
Interface
Counter/
Timing I/O
DAQ-STC
Bus
Interface
DAQ - STC
Timing
FPGA
I/O
Bus
Interface
Analog
Output
Control
Analog Output
Timing/Control
RTSI Bus
Interface
Digital I/O
Digital I/O (8)
AO Control
Data (32)
DAC
FIFO
DAC0
Data (16)
DAC1
RTSI Bus
Calibration
DACs
4
Figure 3-1. PCI-6110E Block Diagram
© National Instruments Corporation
3-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
Figure 3-2 shows a block diagram for the PCI-6111E board.
CH0+
+
AI CH0
Mux
12
12
CH0
Latch
CH0
Amplifier
–
CH0
12-Bit ADC
Data (16)
Control
CH0-
Generic
Bus
Interface
PCI
Bus
Interface
Mini
MITE
ADC
FIFO
Data (32)
CH1+
+
Address/Data
AI CH1
Mux
CH1
Latch
CH1
Amplifier
–
CH1
12-Bit ADC
Data (16)
AI Control
CH1-
Calibration
Mux
EEPROM
IRQ
DMA
Analog
Trigger
Circuitry
2
Trigger
Trigger Level
DACs
Analog Input
Timing/Control
DMA/IRQ
Trigger
PFI / Trigger
Analog
EEPROM
DMA
Input
Control Interface
Control
Bus
Interface
Counter/
Timing I/O
DAQ-STC
Bus
Interface
DAQ - STC
Timing
FPGA
I/O
Bus
Interface
Analog
Output
Control
Analog Output
Timing/Control
RTSI Bus
Interface
Digital I/O
Digital I/O (8)
AO Control
Data (32)
DAC
FIFO
DAC0
DAC1
RTSI Bus
Calibration
DACs
4
Figure 3-2. PCI-6111E Block Diagram
Analog Input
The analog input section for the 611X E board is software configurable.
You can select different analog input configurations through
application software. The following sections describe in detail each of
the analog input categories.
Input Mode
The 611X E board supports only differential inputs (DIFF). The DIFF
input configuration provides up to four channels on the PCI-6110E
board and up to two channels on the PCI-6111E board.
A channel configured in DIFF mode uses two analog channel input lines.
One line connects to the positive input of the board programmable gain
instrumentation amplifier (PGIA), and the other connects to the negative
input of the PGIA. For more information about DIFF input
PCI-6110E/6111E User Manual
3-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
configuration, refer to the Analog Input Signal Connections section in
Chapter 4, Signal Connections, which contains diagrams showing the
signal paths for DIFF input.
Input Polarity and Input Range
The 611X E board has bipolar inputs only. Bipolar input means that the
input voltage range is between –V /2 and + V /2. These boards have
ref
ref
a bipolar input range of 20 V (±10 V).
You can program range settings on a per channel basis so that you can
configure each input channel uniquely.
The software-programmable gain on these boards increases their
overall flexibility by matching the input signal ranges to those that the
ADC can accommodate. They have gains of 0.2, 0.5, 1, 2, 5, 10, 20, and
50, and are suited for a wide variety of signal levels. With the proper
gain setting, you can use the full resolution of the ADC to measure the
input signal. Table 3-1 shows the overall input range and precision
according to the gain used.
Table 3-1. Actual Range and Measurement Precision
Range
Configuration
1
2
Gain
Actual Input Range
Precision
–10 to +10 V
0.2
0.5
1.0
–50 to +50 V
–20 to +20 V
–10 to +10 V
–5 to +5 V
24.41 mV
9.77 mV
4.88 mV
2.0
2.44 mV
5.0
–2 to +2 V
–1 to +1V
–500 to +500 mV
–200 to +200 mV
976.56 µV
488.28 µV
244.14 µV
97.66 µV
10.0
20.0
50.0
1
Warning: The 611X E is not designed for input voltages greater than 42 V, even if a
user-installed voltage divider reduces the voltage to within the input range of the DAQ
device. Input voltages greater than 42 V can damage the 611X E, any device connected to
it, and the host computer. Overvoltage can also cause an electric shock hazard for the
operator. National Instruments is NOT liable for damage or injury resulting from such
misuse.
2
The value of 1 LSB of the 12-bit ADC; that is, the voltage increment corresponding to a
change of one count in the ADC 12-bit count.
Note: See Appendix A, Specifications, for absolute maximum ratings.
© National Instruments Corporation
3-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
Considerations for Selecting Input Ranges
The range you select depends on the expected range of the incoming
signal. A large input range can accommodate a large signal variation
but reduces the voltage resolution. Choosing a smaller input range
improves the voltage resolution but may result in the input signal going
out of range. For best results, match the input range as closely as
possible to the expected range of the input signal.
Input Coupling
Dither
You can configure the 611X E board for either AC or DC input coupling
on a per channel basis. Use AC coupling when your AC signal contains
a large DC component. If you enable AC coupling, you remove the
large DC offset for the input amplifier and amplify only the AC
component. This makes effective use of the ADC dynamic range.
Dither adds approximately 0.5 LSBrms of white Gaussian noise to
the signal to be converted by the ADC. This addition is useful for
applications involving averaging to increase the resolution of the
611X E board, as in calibration or spectral analysis. In such
applications, noise modulation is decreased and differential linearity is
of quantization and reduces measurement noise, resulting in improved
resolution.
Figure 3-3 illustrates the effect of dither on signal acquisition.
Figure 3-3a shows a small (±4 LSB) sine wave acquired without dither.
The ADC quantization is clearly visible. Figure 3-3b shows what
happens when 50 such acquisitions are averaged together; quantization
is still plainly visible. In Figure 3-3c, the sine wave is acquired with
dither. There is a considerable amount of visible noise. But averaging
about 50 such acquisitions, as shown in Figure 3-3d, eliminates both the
added noise and the effects of quantization. Dither has the effect of
forcing quantization noise to become a zero-mean random variable
rather than a deterministic function of the input signal.
PCI-6110E/6111E User Manual
3-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
You cannot disable dither on the 611X E board. This is because the
ADC resolution is so fine that the ADC and the PGIA inherently
produce almost 0.5 LSBrms of noise. This is equivalent to having a
dither circuit that is always enabled.
LSBs
6.0
LSBs
6.0
4.0
2.0
4.0
2.0
0.0
0.0
-2.0
-4.0
-6.0
-2.0
-4.0
-6.0
0
100
200
300
400
500
0
100
200
300
400
500
a. Dither disabled; no averaging
b. Dither disabled; average of 50 acquisitions
LSBs
6.0
LSBs
6.0
4.0
2.0
4.0
2.0
0.0
0.0
-2.0
-4.0
-6.0
-2.0
-4.0
-6.0
0
100
200
300
400
500
0
100
200
300
400
500
c. Dither enabled; no averaging
d. Dither enabled; average of 50 acquisitions
Figure 3-3. Effects of Dither on Signal Acquisition
Analog Output
The 611X E board supplies two channels of analog output voltage at the
I/O connector. The range is fixed at bipolar ±10 V.
© National Instruments Corporation
3-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
Analog Trigger
In addition to supporting internal software triggering and external
digital triggering to initiate a data acquisition sequence, these boards
also support analog triggering. You can configure the analog trigger
circuitry to accept either a direct analog input from the PFI0/TRIG1 pin
on the I/O connector or a postgain signal from the output of the PGIA
on any of the channels, as shown in Figures 3-4 and 3-5. The
trigger-level range for the direct analog channel is ±10 V in 78 mV steps
for the 611X E board. The range for the post-PGIA trigger selection is
simply the full-scale range of the selected channel, and the resolution is
that range divided by 256.
Note:
The PFI0/TRIG1 pin is an analog input when configured as an analog
trigger. Therefore, it is susceptible to crosstalk from adjacent pins, which
can result in false triggering when the pin is left unconnected. To avoid
false triggering, make sure this pin is connected to a low-impedance signal
source (less than 1 kΩ source impedance) if you plan to enable this input
via software.
ADC
+
Analog
Input
CH0
PGIA
-
ADC
+
Analog
Input
CH1
PGIA
-
ADC
Analog
Trigger
Circuit
Mux
+
-
DAQ-STC
Analog
Input
CH2
PGIA
PGIA
ADC
+
-
Analog
Input
CH3
PFI0/TRIG1
Figure 3-4. Analog Trigger Block Diagram for the PCI-6110E
PCI-6110E/6111E User Manual
3-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
ADC
ADC
+
-
Analog
Input
CH0
PGIA
PGIA
Analog
Trigger
Circuit
Mux
DAQ-STC
+
-
Analog
Input
CH1
PFI0/TRIG1
Figure 3-5. Analog Trigger Block Diagram for the PCI-6111E
Five analog triggering modes are available, as shown in Figures 3-6
through 3-10. You can set lowValue and highValue independently in
software.
In below-low-level analog triggering mode, the trigger is generated
when the signal value is less than lowValue, as shown in Figure 3-6.
HighValue is unused.
lowValue
Trigger
Figure 3-6. Below-Low-Level Analog Triggering Mode
© National Instruments Corporation
3-7
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
In above-high-level analog triggering mode, the trigger is generated
when the signal value is greater than highValue, as shown in Figure 3-7.
LowValue is unused.
highValue
Trigger
Figure 3-7. Above-High-Level Analog Triggering Mode
In inside-region analog triggering mode, the trigger is generated when
the signal value is between the lowValue and the highValue, as shown
in Figure 3-8.
highValue
lowValue
Trigger
Figure 3-8. Inside-Region Analog Triggering Mode
PCI-6110E/6111E User Manual
3-8
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
In high-hysteresis analog triggering mode, the trigger is generated when
the signal value is greater than highValue, with the hysteresis specified
by lowValue, as shown in Figure 3-9.
highValue
lowValue
Trigger
Figure 3-9. High-Hysteresis Analog Triggering Mode
In low-hysteresis analog triggering mode, the trigger is generated when
the signal value is less than lowValue, with the hysteresis specified by
highValue, as shown in Figure 3-10.
highValue
lowValue
Trigger
Figure 3-10. Low-Hysteresis Analog Triggering Mode
The analog trigger circuit generates an internal digital trigger based on
the analog input signal and the user-defined trigger levels. This digital
trigger can be used by any of the timing sections of the DAQ-STC,
including the analog input, analog output, and general-purpose
counter/timer sections. For example, the analog input section can be
configured to acquire n scans after the analog input signal crosses a
specific threshold. As another example, the analog output section can
be configured to update its outputs whenever the analog input signal
crosses a specific threshold.
© National Instruments Corporation
3-9
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
Digital I/O
The 611X E board contains eight lines of digital I/O for general-purpose
use. You can individually software-configure each line for either input
or output. At system startup and reset, the digital I/O ports are all high
impedance.
The hardware up/down control for general-purpose counters 0 and 1 are
connected onboard to DIO6 and DIO7, respectively. Thus, you can use
DIO6 and DIO7 to control the general-purpose counters. The up/down
control signals are input only and do not affect the operation of the DIO
lines.
PCI-6110E/6111E User Manual
3-10
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
Timing Signal Routing
The DAQ-STC provides a very flexible interface for connecting timing
signals to other boards or external circuitry. The 611X E board uses the
RTSI bus to interconnect timing signals between boards, and the
Programmable Function Input (PFI) pins on the I/O connector to
connect the board to external circuitry. These connections are designed
to enable the 611X E board to both control and be controlled by other
boards and circuits.
There are a total of 13 timing signals internal to the DAQ-STC that can
be controlled by an external source. These timing signals can also be
controlled by signals generated internally to the DAQ-STC, and these
selections are fully software configurable. For example, the signal
routing multiplexer for controlling the CONVERT* signal is shown in
Figure 3-11.
RTSI Trigger <0..6>
CONVERT*
PFI<0..9>
Sample Interval Counter TC
GPCTR0_OUT
Figure 3-11. CONVERT* Signal Routing
© National Instruments Corporation
3-11
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
sources, including the external signals RTSI<0..6> and PFI<0..9> and
the internal signals Sample Interval Counter TC and GPCTR0_OUT.
Many of these timing signals are also available as outputs on the RTSI
pins, as indicated in the RTSI Triggers section later in this chapter, and
on the PFI pins, as indicated in Chapter 4, Signal Connections.
Programmable Function Inputs
The 10 PFIs are connected to the signal routing multiplexer for each
timing signal, and software can select one of the PFIs as the external
source for a given timing signal. It is important to note that any of the
PFIs can be used as an input by any of the timing signals and that
multiple timing signals can use the same PFI simultaneously. This
flexible routing scheme reduces the need to change physical
connections to the I/O connector for different applications. You can
also individually enable each of the PFI pins to output a specific internal
timing signal. For example, if you need the UPDATE* signal as an
output on the I/O connector, software can turn on the output driver for
the PFI5/UPDATE* pin.
Board and RTSI Clocks
Many functions performed by the 611X E board require a frequency
timebase to generate the necessary timing signals for controlling A/D
conversions, DAC updates, or general-purpose signals at the I/O
connector.
The 611X E board can use either its internal 20 MHz timebase or a
timebase received over the RTSI bus. In addition, if you configure the
board to use the internal timebase, you can also program the board to
drive its internal timebase over the RTSI bus to another board that is
programmed to receive this timebase signal. This clock source, whether
local or from the RTSI bus, is used directly by the board as the primary
frequency source. The default configuration at startup is to use the
internal timebase without driving the RTSI bus timebase signal. This
timebase is software selectable.
PCI-6110E/6111E User Manual
3-12
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
RTSI Triggers
The seven RTSI trigger lines on the RTSI bus provide a very flexible
interconnection scheme for the 611X E board sharing the RTSI bus.
These bidirectional lines can drive any of eight timing signals onto the
RTSI bus and can receive any of these timing signals. This signal
connection scheme is shown in Figure 3-12.
DAQ-STC
TRIG1
TRIG2
CONVERT*
UPDATE*
WFTRIG
GPCTR0_SOURCE
GPCTR0_GATE
GPCTR0_OUT
STARTSCAN
AIGATE
Trigger
7
SISOURCE
UISOURCE
GPCTR1_SOURCE
RTSI_OSC (20 MHz)
Clock
Figure 3-12. RTSI Bus Signal Connection
Refer to the Timing Connections section of Chapter 4, Signal
Connections, for a description of the signals shown in Figure 3-12.
© National Instruments Corporation
3-13
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Signal Connections
This chapter describes how to make input and output signal connections
to your 611X E board via the board I/O connector.
to 68-pin accessories with the SH6868EP shielded cable.
I/O Connector
the 611X E board. A signal description follows the connector pinouts.
Caution: Connections that exceed any of the maximum ratings of input or output
signals on the 611X E board can damage the 611X E board and the
computer. Maximum input ratings for each signal are given in the
Protection column of Table 4-2. National Instruments is NOT liable for
any damages resulting from such signal connections.
!
© National Instruments Corporation
4-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
34 68
ACH1+ 33 67
ACH0–
ACH0+
ACH0GND
ACH1–
ACH2+1
ACH2GND1
ACH3–1
NC
32 66
31 65
30 64
29 63
28 62
ACH1GND
ACH2–1
ACH3+1
ACH3GND1
NC
NC 27 61
NC 26 60
NC
NC
NC
NC 24 58
25 59
NC
NC
NC
23 57
22 56
21 55
NC
NC
DAC0OUT
DAC1OUT
AOGND
AOGND
DGND
DIO0
NC 20 54
19 53
18 52
17 51
16 50
15 49
DIO4
DGND
DIO1
DIO5
DIO6
DGND
DIO2
DGND
+5 V 14 48
DGND 13 47
DGND 12 46
DIO7
DIO3
SCANCLK
PFI0/TRIG1
11 45
10 44
EXTSTROBE*
DGND
PFI1/TRIG2
DGND
9
8
7
6
5
4
3
2
1
43
42
41
40
39
38
37
36
35
PFI2/CONVERT*
PFI3/GPCTR1_SOURCE
PFI4/GPCTR1_GATE
GPCTR1_OUT
DGND
+5 V
DGND
PFI5/UPDATE*
PFI6/WFTRIG
DGND
PFI7/STARTSCAN
PFI8/GPCTR0_SOURCE
DGND
PFI9/GPCTR0_GATE
GPCTR0_OUT
FREQ_OUT
DGND
1 NC on PCI-6111E
PCI-6110E/6111E User Manual
4-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
I/O Connector Signal Descriptions
Table 4-1. Signal Descriptions for I/O Connector Pins
Signal Name
Reference
Direction
Description
ACH <0..3> GND
—
—
Analog Input Channels 0 through 3 ground—These pins are
the bias current return point for differential measurements.
ACH <2..3> GND signals are no connects on the
PCI-6111E.
ACH<0..3> +
ACH<0..3> –
ACH <0..3>
GND
Input
Input
Analog Input Channels 0 through 3 (+)—These pins are
routed to the (+) terminal of the respective channel’s
amplifier. ACH <2..3> + signals are no connects on the
PCI-6111E.
ACH <0..3>
GND
Analog Input Channels 0 through 3 (–)—These pins are
routed to the (–) terminal of the respective channel’s
amplifier. ACH <2..3> – signals are no connects on the
PCI-6111E.
DAC0OUT
DAC1OUT
AOGND
DGND
AOGND
AOGND
—
Output
Output
—
Analog Channel 0 Output—This pin supplies the voltage
output of analog output channel 0.
Analog Channel 1 Output—This pin supplies the voltage
output of analog output channel 1.
Analog Output Ground—The analog output voltages are
referenced to this node.
—
—
Digital Ground—This pin supplies the reference for the
digital signals at the I/O connector as well as the +5 VDC
supply.
DIO<0..7>
+5 V
DGND
DGND
DGND
Input or
Output
Digital I/O signals—DIO6 and 7 can control the up/down
signal of general-purpose counters 0 and 1, respectively.
Output
Output
+5 VDC Source—These pins are fused for up to 1 A of
+5 V supply. The fuse is self-resetting.
SCANCLK
Scan Clock—This pin pulses once for each A/D conversion
when enabled. The low-to-high edge indicates when the
input signal can be removed from the input or switched to
another signal.
EXTSTROBE*
DGND
Output
External Strobe—This output can be toggled under software
control to latch signals or trigger events on external devices.
© National Instruments Corporation
4-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Table 4-1. Signal Descriptions for I/O Connector Pins (Continued)
Signal Name
PFI0/TRIG1
Reference
Direction
DGND
Input
PFI0/Trigger 1—As an input, this is either one of the
Programmable Function Inputs (PFIs) or the source for the
hardware analog trigger. PFI signals are explained in the
Timing Connections section later in this chapter. The
hardware analog trigger is explained in the Analog Trigger
section in Chapter 3, Hardware Overview.
Output
As an output, this is the TRIG1 signal. In posttrigger data
acquisition sequences, a low-to-high transition indicates the
initiation of the acquisition sequence. In pretrigger
applications, a low-to-high transition indicates the initiation
of the pretrigger conversions.
PFI1/TRIG2
DGND
Input
PFI1/Trigger 2—As an input, this is one of the PFIs.
Output
As an output, this is the TRIG2 signal. In pretrigger
applications, a low-to-high transition indicates the initiation
of the posttrigger conversions. TRIG2 is not used in
posttrigger applications.
PFI2/CONVERT*
DGND
DGND
Input
PFI2/Convert—As an input, this is one of the PFIs.
Output
As an output, this is the CONVERT* signal. A high-to-low
edge on CONVERT* indicates that an A/D conversion is
occurring.
PFI3/GPCTR1_SOURCE
Input
PFI3/Counter 1 Source—As an input, this is one of the
PFIs.
Output
As an output, this is the GPCTR1_SOURCE signal. This
signal reflects the actual source connected to the
general-purpose counter 1.
PFI4/GPCTR1_GATE
DGND
Input
PFI4/Counter 1 Gate—As an input, this is one of the PFIs.
Output
As an output, this is the GPCTR1_GATE signal. This signal
reflects the actual gate signal connected to the
general-purpose counter 1.
GPCTR1_OUT
PFI5/UPDATE*
DGND
DGND
Output
Counter 1 Output—This output is from the general-purpose
counter 1 output.
Input
PFI5/Update—As an input, this is one of the PFIs.
Output
As an output, this is the UPDATE* signal. A high-to-low
edge on UPDATE* indicates that the analog output primary
group is being updated.
PCI-6110E/6111E User Manual
4-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Table 4-1. Signal Descriptions for I/O Connector Pins (Continued)
Signal Name
PFI6/WFTRIG
Reference
Direction
Description
DGND
Input
PFI6/Waveform Trigger—As an input, this is one of the
PFIs.
Output
As an output, this is the WFTRIG signal. In timed analog
output sequences, a low-to-high transition indicates the
initiation of the waveform generation.
PFI7/STARTSCAN
DGND
DGND
DGND
Input
PFI7/Start of Scan—As an input, this is one of the PFIs.
Output
As an output, this is the STARTSCAN signal. This pin
pulses once at the start of each analog input scan in the
interval scan. A low-to-high transition indicates the start of
the scan.
PFI8/GPCTR0_SOURCE
PFI9/GPCTR0_GATE
Input
PFI8/Counter 0 Source—As an input, this is one of the
PFIs.
Output
As an output, this is the GPCTR0_SOURCE signal. This
signal reflects the actual source connected to the
general-purpose counter 0.
Input
PFI9/Counter 0 Gate—As an input, this is one of the PFIs.
Output
As an output, this is the GPCTR0_GATE signal. This signal
reflects the actual gate signal connected to the
general-purpose counter 0.
GPCTR0_OUT
FREQ_OUT
DGND
DGND
Output
Output
Counter 0 Output—This output is from the general-purpose
counter 0 output.
Frequency Output—This output is from the frequency
generator output.
© National Instruments Corporation
4-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Table 4-2 shows the I/O signal summary for the 611X E boards.
Table 4-2. I/O Signal Summary for the 611X E
Signal Impedance
Typeand Input/
Direction Output
Protection
(Volts)
On/Off
Sink
(mA
at V)
Rise
Time
(ns)
Source
(mA at V)
Signal Name
ACH<0..3> +
Bias
AI
1 MΩ
42 V
—
—
—
—
in parallel
with
100 pF1
1 MΩ
in parallel
with
10 pF2
ACH<0..3> –
ACH <0..3> GND
DAC0OUT
AI
10 nF
—
42 V
—
—
—
—
—
—
±200 pA
—
AI
—
AO
50 Ω
Short-circuit
to ground
5 at 10
5 at -10 300
V/µs
—
DAC1OUT
AO
50 Ω
Short-circuit
to ground
5 at 10
5 at -10 300
V/µs
—
AOGND
DGND
VCC
AO
DO
DO
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.1 Ω
Short-circuit
to ground
1 A
DIO<0..7>
DIO
—
V
+0.5
13 at (V -0.4)
cc
24 at
0.4
1.1
50 kΩ pu
cc
SCANCLK
DO
DO
—
—
3.5 at (V -0.4) 5 at 0.4
cc
1.5
1.5
1.5
50 kΩ pu
EXTSTROBE*
PFI0/TRIG1
—
—
3.5 at (V -0.4) 5 at 0.4
cc
50 kΩ pu
AI
DIO
10 kΩ
±35
3.5 at (V -0.4) 5 at 0.4
cc
9 kΩ pu
and10 kΩ
pd
V
+0.5
cc
PFI1/TRIG2
DIO
DIO
—
—
V
+0.5
+0.5
+0.5
3.5 at (V -0.4) 5 at 0.4
cc
1.5
1.5
1.5
50 kΩ pu
50 kΩ pu
50 kΩ pu
cc
PFI2/CONVERT*
PFI3/GPCTR1_SOURCE
V
3.5 at (V -0.4) 5 at 0.4
cc
cc
V
3.5 at (V -0.4) 5 at 0.4
cc
cc
PCI-6110E/6111E User Manual
4-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Table 4-2. I/O Signal Summary for the 611X E (Continued)
Signal Impedance
Typeand Input/
Direction Output
Protection
(Volts)
On/Off
Sink
(mA
at V)
Rise
Time
(ns)
Source
(mA at V)
Signal Name
PFI4/GPCTR1_GATE
GPCTR1_OUT
Bias
DIO
DO
—
—
—
—
—
—
—
—
—
V
+0.5
3.5 at (V -0.4) 5 at 0.4
cc
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
50 kΩ pu
cc
—
V
3.5 at (V -0.4) 5 at 0.4
cc
PFI5/UPDATE*
DIO
DIO
DIO
DIO
DIO
DO
+0.5
+0.5
+0.5
+0.5
+0.5
3.5 at (V -0.4) 5 at 0.4
cc
cc
PFI6/WFTRIG
V
V
V
V
3.5 at (V -0.4) 5 at 0.4
cc
cc
cc
cc
cc
PFI7/STARTSCAN
PFI8/GPCTR0_SOURCE
PFI9/GPCTR0_GATE
GPCTR0_OUT
3.5 at (V -0.4) 5 at 0.4
cc
3.5 at (V -0.4) 5 at 0.4
cc
3.5 at (V -0.4) 5 at 0.4
cc
—
—
3.5 at (V -0.4) 5 at 0.4
cc
FREQ_OUT
DO
3.5 at (V -0.4)
cc
5 at 0.4
1 Applies to gain ≤ 1, impedance refers to ACH<0..3>–
2Applies to gain > 1, impedance refers to ACH<0..3>–
AI = Analog Input, DIO = Digital Input/Output, pu = pull-up, AO = Analog Output, DO = Digital Output,
AI/DIO = Analog Input/Digital Input/Output
The tolerance on the 50 kΩ pull-up and pull-down resistors is very large. Actual value may range between 17 and 100 kΩ.
© National Instruments Corporation
4-7
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Analog Input Signal Connections
The analog input signals for the 611X E board are ACH<0..3>+ and
ACH<0..3>–. The ACH<0..3>+ signals are routed to the positive input
of the PGIA, and signals connected to ACH<0..3>– are routed to the
negative input of the PGIA.
Caution: Exceeding the differential and common-mode input ranges distorts your
input signals. Exceeding the maximum input voltage rating can damage
the 611X E board and the computer. National Instruments is NOT liable for
any damages resulting from such signal connections. The maximum input
voltage ratings are listed in the Protection column of Table 4-2.
!
With the different configurations, you can use the PGIA in different
ways. Figure 4-2 shows a diagram of your 611X E board PGIA.
Instrumentation
Amplifier
Vin+
+
+
PGIA
Vm
Measured
Voltage
Vin-
-
-
Vm = [Vin+ - Vin-]* Gain
Figure 4-2. 611X E Board PGIA
The PGIA applies gain and common-mode voltage rejection and
presents high input impedance to the analog input signals connected to
the 611X E board. Signals are routed to the positive and negative inputs
of the PGIA. The PGIA converts two input signals to a signal that is the
difference between the two input signals multiplied by the gain setting
of the amplifier. The amplifier output voltage is referenced to the
ground for the board. The 611X E board A/D converter (ADC) measures
this output voltage when it performs A/D conversions.
PCI-6110E/6111E User Manual
4-8
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Types of Signal Sources
When making signal connections, you must first determine whether the
signal sources are floating or ground-referenced. The following
sections describe these two types of signals.
Floating Signal Sources
A floating signal source is not connected in any way to the building
ground system but, rather, has an isolated ground-reference point. Some
examples of floating signal sources are outputs of transformers,
thermocouples, battery-powered devices, optical isolator outputs, and
isolation amplifiers. An instrument or device that has an isolated output
is a floating signal source. You must tie the ground reference of a
floating signal to the 611X E board analog input ground to establish a
local or onboard reference for the signal. Otherwise, the measured input
signal varies as the source floats out of the common-mode input range.
Ground-Referenced Signal Sources
A ground-referenced signal source is connected in some way to the
building system ground and is, therefore, already connected to a
common ground point with respect to the 611X E board, assuming that
the computer is plugged into the same power system. Nonisolated
outputs of instruments and devices that plug into the building power
system fall into this category.
The difference in ground potential between two instruments connected
to the same building power system is typically between 1 and 100 mV
but can be much higher if power distribution circuits are not properly
connected. If a grounded signal source is improperly measured, this
difference may appear as an error in the measurement. The connection
instructions for grounded signal sources are designed to eliminate this
ground potential difference from the measured signal.
Differential Measurements
The following sections discuss the use of differential (DIFF)
measurements and considerations for measuring both floating and
ground-referenced signal sources.
© National Instruments Corporation
4-9
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Table 4-3 summarizes the recommended DIFF signal connections and
includes input examples for both types of signal sources.
Table 4-3. Signal Source Types
DIFF Input
Examples and
Signal Source
Floating Signal Source
(Not Connected to Building Ground)
Grounded Signal Source
Input Examples
• Ungrounded Thermocouples
• Plug-in cards with nonisolated
outputs
• Signal conditioning with isolated
outputs
• Battery devices
Differential
(DIFF)
ACH0(+)
ACH0(+)
+
+
+
+
V
V
1
ACH0(-)
1
ACH0(-)
-
-
-
-
ACH0GND
ACH0GND
See text for information on bias resistors.
Differential Connection Considerations
A differential connection is one in which the 611X E board analog input
signal has its own reference signal or signal return path. The 611X E
channels are always configured in DIFF input mode. The input signal is
tied to the positive input of the PGIA, and its reference signal, or return,
is tied to the negative input of the PGIA.
Each differential signal uses two inputs—one for the signal and one for
its reference signal.
Differential signal connections reduce picked up noise and increase
common-mode noise rejection. Differential signal connections also
allow input signals to float within the common-mode limits of the
PGIA.
PCI-6110E/6111E User Manual
4-10
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Differential Connections for Ground-Referenced
Signal Sources
Figure 4-3 shows how to connect a ground-referenced signal source to
a channel on the 611X E board.
Instrumentation
ACH0+
ACH0-
Amplifier
+
-
Ground-
Referenced
Signal
+
Vs
PGIA
+
-
Source
-
Measured
Voltage
Vm
Common-
Mode
Noise and
Ground
+
Vcm
-
Potential
ACH0GND
I/O Connector
ACH0 Connections Shown
Figure 4-3. Differential Input Connections for Ground-Referenced Signals
With this type of connection, the PGIA rejects both the common-mode
noise in the signal and the ground potential difference between the
signal source and the 611X E board ground, shown as V in Figure 4-3.
cm
Differential Connections for Nonreferenced or
Floating Signal Sources
Figure 4-4 shows how to connect a floating signal source to a channel
on the 611X E board.
© National Instruments Corporation
4-11
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
ACH0+
ACH0-
Instrumentation
Amplifier
+
Floating
Signal
Source
+
-
VS
100pf
1MΩ
-
PGIA
+
-
Measured
Voltage
Vm
Bias
Current
Return
Paths
10nf
Bias
Resistor
(see text)
ACH0GND
I/O Connector
ACH0 Connections Shown
Figure 4-4. Differential Input Connections for Nonreferenced Signals
Figure 4-4 shows a bias resistor connected between ACH0 – and the
floating signal source ground. If you do not use the resistor and the
source is truly floating, the source is not likely to remain within the
causing erroneous readings. You must reference the source to the
respective channel ground.
Common-Mode Signal Rejection Considerations
Figure 4-3 shows connections for signal sources that are already
referenced to some ground point with respect to the 611X E board. In
this case, the PGIA can reject any voltage caused by ground potential
differences between the signal source and the board. In addition, with
differential input connections, the PGIA can reject common-mode noise
pickup in the leads connecting the signal sources to the board. The
+
-
PGIA can reject common-mode signals as long as V
and V (input
in
in
signals) are both within ±11 V of the channel ground, for gain ≥ 1. For
gain <1, the input signals, for ACHO +, can be within ±42 V of the
channel ground.
PCI-6110E/6111E User Manual
4-12
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Analog Output Signal Connections
The analog output signals are DAC0OUT, DAC1OUT, and AOGND.
DAC0OUT is the voltage output signal for analog output channel 0.
DAC1OUT is the voltage output signal for analog output channel 1.
AOGND is the ground reference signal for the analog output channels.
Figure 4-5 shows how to make analog output connections to the
611X E board.
DAC0OUT
Channel 0
+
VOUT 0
Load
Load
-
AOGND
-
VOUT 1
DAC1OUT
+
Channel 1
Analog Output Channels
611X E Board
Figure 4-5. Analog Output Connections
Digital I/O Signal Connections
The digital I/O signals are DIO<0..7> and DGND. DIO<0..7> are the
signals making up the DIO port, and DGND is the ground reference
signal for the DIO port. You can program all lines individually to be
inputs or outputs.
© National Instruments Corporation
4-13
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Caution: Exceeding the maximum input voltage ratings, which are listed in
Table 4-2, can damage the 611X E board and the computer. National
Instruments is NOT liable for any damages resulting from such signal
connections.
!
Figure 4-6 shows signal connections for three typical digital I/O
applications.
+5 V
LED
DIO<4..7>
TTL Signal
DIO<0..3>
+5 V
Switch
DGND
I/O Connector
611X E Board
Figure 4-6. Digital I/O Connections
Figure 4-6 shows DIO<0..3> configured for digital input and
DIO<4..7> configured for digital output. Digital input applications
include receiving TTL signals and sensing external device states such
as the switch state shown in Figure 4-6. Digital output applications
include sending TTL signals and driving external devices such as the
LED shown in Figure 4-6.
PCI-6110E/6111E User Manual
4-14
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Power Connections
Two pins on the I/O connector supply +5 V from the computer power
supply via a self-resetting fuse. The fuse will reset automatically within
a few seconds after the overcurrent condition is removed. These pins are
referenced to DGND and can be used to power external digital circuitry.
•
Power rating
+4.65 to +5.25 VDC at 1 A
Caution: Under no circumstances should you connect these +5 V power pins directly
to analog or digital ground or to any other voltage source on the 611X E
board or any other device. Doing so can damage the 611X E board and the
computer. National Instruments is NOT liable for damages resulting from
such a connection.
!
Timing Connections
Caution: Exceeding the maximum input voltage ratings, which are listed in
!
Table 4-2, can damage the 611X E board and the computer. National
connections.
All external control over the timing of the 611X E board is routed
through the 10 programmable function inputs labeled PFI0 through
PFI9. These signals are explained in detail in the next section,
Programmable Function Input Connections. These PFIs are
bidirectional; as outputs they are not programmable and reflect the state
of many DAQ, waveform generation, and general-purpose timing
signals. There are five other dedicated outputs for the remainder of the
control any DAQ, waveform generation, and general-purpose timing
The DAQ signals are explained in the DAQ Timing Connections section
later in this chapter. The waveform generation signals are explained in
the Waveform Generation Timing Connections section later in this
chapter. The general-purpose timing signals are explained in the
General-Purpose Timing Signal Connections section later in this
chapter.
© National Instruments Corporation
4-15
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
All digital timing connections are referenced to DGND. This reference
is demonstrated in Figure 4-7, which shows how to connect an external
TRIG1 source and an external CONVERT* source to two 611X E board
PFI pins.
PFI0/TRIG1
PFI2/CONVERT*
TRIG1
Source
CONVERT*
Source
DGND
I/O Connector
611X E Board
Figure 4-7. Timing I/O Connections
Programmable Function Input Connections
There are a total of 13 internal timing signals that you can externally
control from the PFI pins. The source for each of these signals is
software-selectable from any of the PFIs when you want external
control. This flexible routing scheme reduces the need to change the
physical wiring to the board I/O connector for different applications
requiring alternative wiring.
internal timing signal. For example, if you need the CONVERT* signal
as an output on the I/O connector, software can turn on the output driver
PCI-6110E/6111E User Manual
4-16
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
for the PFI2/CONVERT* pin. Be careful not to drive a PFI signal
externally when it is configured as an output.
As an input, you can individually configure each PFI for edge or level
detection and for polarity selection, as well. You can use the polarity
selection for any of the 13 timing signals, but the edge or level detection
will depend upon the particular timing signal being controlled. The
detection requirements for each timing signal are listed within the
section that discusses that individual signal.
In edge-detection mode, the minimum pulse width required is 10 ns.
This applies for both rising-edge and falling-edge polarity settings.
There is no maximum pulse-width requirement in edge-detect mode.
In level-detection mode, there are no minimum or maximum
pulse-width requirements imposed by the PFIs themselves, but there
may be limits imposed by the particular timing signal being controlled.
These requirements are listed later in this chapter.
DAQ Timing Connections
The DAQ timing signals are SCANCLK, EXTSTROBE*, TRIG1,
TRIG2, STARTSCAN, CONVERT*, AIGATE, and SISOURCE.
Posttriggered data acquisition allows you to view only data that is
acquired after a trigger event is received. A typical posttriggered DAQ
sequence is shown in Figure 4-8. Pretriggered data acquisition allows
you to view data that is acquired before the trigger of interest in addition
to data acquired after the trigger. Figure 4-9 shows a typical
pretriggered DAQ sequence. The description for each signal shown in
these figures is included later in this chapter.
TRIG1
STARTSCAN
CONVERT*
Scan Counter
4
3
2
1
0
Figure 4-8. Typical Posttriggered Acquisition
© National Instruments Corporation
4-17
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
TRIG1
Don't Care
TRIG2
STARTSCAN
CONVERT*
Scan Counter
3
2
1
0
2
2
2
1
0
Figure 4-9. Typical Pretriggered Acquisition
SCANCLK Signal
SCANCLK is an output-only signal that generates a pulse with the
leading edge occurring approximately 50 to 100 ns after an A/D
conversion begins. The polarity of this output is software-selectable but
is typically configured so that a low-to-high leading edge can clock
external analog input multiplexers indicating when the input signal has
been sampled and can be removed. This signal has a 450 ns pulse width
and is software enabled. Figure 4-10 shows the timing for the
SCANCLK signal.
CONVERT*
t
d
SCANCLK
t
w
t
t
d
= 50 to 100 ns
w = 450 ns
Figure 4-10. SCANCLK Signal Timing
EXTSTROBE* Signal
EXTSTROBE* is an output-only signal that generates either a single
pulse or a sequence of eight pulses in the hardware-strobe mode. An
external device can use this signal to latch signals or to trigger events.
In the single-pulse mode, software controls the level of the
EXTSTROBE* signal. A 10 µs and a 1.2 µs clock are available for
generating a sequence of eight pulses in the hardware-strobe mode.
PCI-6110E/6111E User Manual
4-18
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figure 4-11 shows the timing for the hardware-strobe mode
EXTSTROBE* signal.
V
V
OH
OL
t
t
t
w
w
w
= 600 ns or 5 µs
Figure 4-11. EXTSTROBE* Signal Timing
TRIG1 Signal
Any PFI pin can externally input the TRIG1 signal, which is available
as an output on the PFI0/TRIG1 pin.
Refer to Figures 4-8 and 4-9 for the relationship of TRIG1 to the DAQ
sequence.
As an input, the TRIG1 signal is configured in the edge-detection mode.
You can select any PFI pin as the source for TRIG1 and configure the
polarity selection for either rising or falling edge. The selected edge
of the TRIG1 signal starts the data acquisition sequence for both
posttriggered and pretriggered acquisitions. The 611X E supports
analog triggering on the PFI0/TRIG1 pin. See Chapter 3,
Hardware Overview, for more information on analog triggering.
As an output, the TRIG1 signal reflects the action that initiates a DAQ
sequence. This is true even if the acquisition is being externally
triggered by another PFI. The output is an active high pulse with a
pulse width of 25 to 50 ns. This output is set to tri-state at startup.
© National Instruments Corporation
4-19
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figures 4-12 and 4-13 show the input and output timing requirements
for the TRIG1 signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-12. TRIG1 Input Signal Timing
t
w
t
= 25-50 ns
w
Figure 4-13. TRIG1 Output Signal Timing
The board also uses the TRIG1 signal to initiate pretriggered DAQ
operations. In most pretriggered applications, the TRIG1 signal is
generated by a software trigger. Refer to the TRIG2 signal description
for a complete description of the use of TRIG1 and TRIG2 in a
pretriggered DAQ operation.
TRIG2 Signal
Any PFI pin can externally input the TRIG2 signal, which is available
as an output on the PFI1/TRIG2 pin. Refer to Figure 4-9 for the
relationship of TRIG2 to the DAQ sequence.
As an input, the TRIG2 signal is configured in the edge-detection mode.
You can select any PFI pin as the source for TRIG2 and configure the
polarity selection for either rising or falling edge. The selected edge of
the TRIG2 signal initiates the posttriggered phase of a pretriggered
acquisition sequence. In pretriggered mode, the TRIG1 signal initiates
the data acquisition. The scan counter indicates the minimum number
PCI-6110E/6111E User Manual
4-20
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
of scans before TRIG2 can be recognized. After the scan counter
decrements to zero, it is loaded with the number of posttrigger scans to
acquire while the acquisition continues. The board ignores the TRIG2
signal if it is asserted prior to the scan counter decrementing to zero.
After the selected edge of TRIG2 is received, the board will acquire a
fixed number of scans and the acquisition will stop. This mode acquires
data both before and after receiving TRIG2.
As an output, the TRIG2 signal reflects the posttrigger in a pretriggered
acquisition sequence. This is true even if the acquisition is being
externally triggered by another PFI. The TRIG2 signal is not used in
posttriggered data acquisition. The output is an active high pulse with a
pulse width of 25 to 50 ns. This output is set to tri-state at startup.
Figures 4-14 and 4-15 show the input and output timing requirements
for the TRIG2 signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-14. TRIG2 Input Signal Timing
t
w
t
= 25-50 ns
w
Figure 4-15. TRIG2 Output Signal Timing
© National Instruments Corporation
4-21
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
STARTSCAN Signal
Any PFI pin can externally input the STARTSCAN signal, which is
available as an output on the PFI7/STARTSCAN pin. Refer to
Figures 4-8 and 4-9 for the relationship of STARTSCAN to the DAQ
sequence.
As an input, the STARTSCAN signal is configured in the
edge-detection mode. You can select any PFI pin as the source for
STARTSCAN and configure the polarity selection for either rising or
falling edge. The selected edge of the STARTSCAN signal initiates a
scan. The sample interval counter starts if you select internally
triggered CONVERT*.
As an output, the STARTSCAN signal reflects the actual start pulse that
initiates a scan. This is true even if the starts are being externally
triggered by another PFI. You have two output options. The first is an
active high pulse with a pulse width of 25 to 50 ns, which indicates the
terminates at the start of the last conversion in the scan, which indicates
a scan in progress. STARTSCAN will be deasserted toff after the last
conversion in the scan is initiated. This output is set to tri-state at
startup.
Figures 4-16 and 4-17 show the input and output timing requirements
for the STARTSCAN signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-16. STARTSCAN Input Signal Timing
PCI-6110E/6111E User Manual
4-22
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
t
w
STARTSCAN
t
= 25-50 ns
w
a. Start of Scan
Start Pulse
CONVERT*
STARTSCAN
t
off
t
= 10 ns minimum
off
b. Scan in Progress, Two Conversions per Scan
Figure 4-17. STARTSCAN Output Signal Timing
The CONVERT* pulses are masked off until the board generates the
STARTSCAN signal. If you are using internally generated conversions,
the first CONVERT* appears when the onboard sample interval counter
reaches zero. If you select an external CONVERT*, the first external
pulse after STARTSCAN generates a conversion. The STARTSCAN
pulses should be separated by at least one scan period.
A counter on the 611X E board internally generates the STARTSCAN
signal unless you select some external source. This counter is started by
the TRIG1 signal and is stopped either by software or by the sample
counter.
Scans generated by either an internal or external STARTSCAN signal
are inhibited unless they occur within a DAQ sequence. Scans occurring
within a DAQ sequence may be gated by either the hardware (AIGATE)
signal or software command register gate.
CONVERT* Signal
Any PFI pin can externally input the CONVERT* signal, which is
available as an output on the PFI2/CONVERT* pin.
© National Instruments Corporation
4-23
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Refer to Figures 4-8 and 4-9 for the relationship of STARTSCAN to the
DAQ sequence.
As an input, the CONVERT* signal is configured in the edge-detection
mode. You can select any PFI pin as the source for CONVERT* and
configure the polarity selection for either rising or falling edge. The
selected edge of the CONVERT* signal initiates an A/D conversion.
As an output, the CONVERT* signal reflects the actual convert pulse
that is connected to the ADC. This is true even if the conversions are
being externally generated by another PFI. The output is an active low
pulse with a pulse width of 50 to 100 ns. This output is set to tri-state at
startup.
Figures 4-18 and 4-19 show the input and output timing requirements
for the CONVERT* signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-18. CONVERT* Input Signal Timing
t
w
t
= 50-100 ns
w
Figure 4-19. CONVERT* Output Signal Timing
The ADC switches to hold mode within 20 ns of the selected edge. This
hold-mode delay time is a function of temperature and does not vary
from one conversion to the next.
PCI-6110E/6111E User Manual
4-24
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
The sample interval counter on the 611X E board normally generates the
CONVERT* signal unless you select some external source. The counter
is started by the STARTSCAN signal and continues to count down and
reload itself until the scan is finished. It then reloads itself in
preparation for the next STARTSCAN pulse.
A/D conversions generated by either an internal or external
CONVERT* signal are inhibited unless they occur within a DAQ
sequence. Scans occurring within a DAQ sequence may be gated by
either the hardware (AIGATE) signal or software command register
gate.
AIGATE Signal
Any PFI pin can externally input the AIGATE signal, which is not
available as an output on the I/O connector. The AIGATE signal can
mask off scans in a DAQ sequence. You can configure the PFI pin you
select as the source for the AIGATE signal in either the level-detection
or edge-detection mode. You can configure the polarity selection for the
PFI pin for either active high or active low.
In the level-detection mode if AIGATE is active, the STARTSCAN
signal is masked off and no scans can occur. In the edge-detection
mode, the first active edge disables the STARTSCAN signal, and the
second active edge enables STARTSCAN.
The AIGATE signal can neither stop a scan in progress nor continue a
previously gated-off scan; in other words, once a scan has started,
AIGATE does not gate off conversions until the beginning of the next
scan and, conversely, if conversions are being gated off, AIGATE does
not gate them back on until the beginning of the next scan.
SISOURCE Signal
Any PFI pin can externally input the SISOURCE signal, which is not
available as an output on the I/O connector. The onboard scan interval
counter uses the SISOURCE signal as a clock to time the generation of
the STARTSCAN signal. You must configure the PFI pin you select as
the source for the SISOURCE signal in the level-detection mode. You
can configure the polarity selection for the PFI pin for either active high
or active low.
© National Instruments Corporation
4-25
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
The maximum allowed frequency is 20 MHz, with a minimum pulse
width of 23 ns high or low. There is no minimum frequency limitation.
Either the 20 MHz or 100 kHz internal timebase generates the
SISOURCE signal unless you select some external source. Figure 4-20
shows the timing requirements for the SISOURCE signal.
t
p
t
t
w
w
t
= 50 ns minimum
= 23 ns minimum
p
t
w
Figure 4-20. SISOURCE Signal Timing
Waveform Generation Timing Connections
The analog group defined for the 611X E board is controlled by
WFTRIG, UPDATE*, and UISOURCE.
WFTRIG Signal
Any PFI pin can externally input the WFTRIG signal, which is available
as an output on the PFI6/WFTRIG pin.
As an input, the WFTRIG signal is configured in the edge-detection
mode. You can select any PFI pin as the source for WFTRIG and
configure the polarity selection for either rising or falling edge. The
selected edge of the WFTRIG signal starts the waveform generation for
the DACs. The update interval (UI) counter is started if you select
internally generated UPDATE*.
As an output, the WFTRIG signal reflects the trigger that initiates
waveform generation. This is true even if the waveform generation is
being externally triggered by another PFI. The output is an active high
pulse with a pulse width of 25 to 50 ns. This output is set to tri-state at
startup.
PCI-6110E/6111E User Manual
4-26
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figures 4-21 and 4-22 show the input and output timing requirements
for the WFTRIG signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-21. WFTRIG Input Signal Timing
t
w
t
= 25-50 ns
w
Figure 4-22. WFTRIG Output Signal Timing
UPDATE* Signal
Any PFI pin can externally input the UPDATE* signal, which is
available as an output on the PFI5/UPDATE* pin.
As an input, the UPDATE* signal is configured in the edge-detection
mode. You can select any PFI pin as the source for UPDATE* and
configure the polarity selection for either rising or falling edge. The
selected edge of the UPDATE* signal updates the outputs of the DACs.
In order to use UPDATE*, you must set the DACs to posted-update
mode.
As an output, the UPDATE* signal reflects the actual update pulse that
is connected to the DACs. This is true even if the updates are being
externally generated by another PFI. The output is an active low pulse
with a pulse width of 50 to 75 ns. This output is set to tri-state at startup.
© National Instruments Corporation
4-27
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figures 4-23 and 4-24 show the input and output timing requirements
for the UPDATE* signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-23. UPDATE* Input Signal Timing
t
w
t
= 50-75 ns
w
Figure 4-24. UPDATE* Output Signal Timing
The DACs are updated within 100 ns of the leading edge. Separate the
UPDATE* pulses with enough time that new data can be written to the
DAC latches.
The UI counter for the 611X E board normally generates the UPDATE*
signal unless you select some external source. The UI counter is started
by the WFTRIG signal and can be stopped by software or the internal
Buffer Counter.
D/A conversions generated by either an internal or external UPDATE*
signal do not occur when gated by the software command register gate.
UISOURCE Signal
Any PFI pin can externally input the UISOURCE signal, which is not
available as an output on the I/O connector. The UI counter uses the
UISOURCE signal as a clock to time the generation of the UPDATE*
signal. You must configure the PFI pin you select as the source for the
UISOURCE signal in the level-detection mode. You can configure the
PCI-6110E/6111E User Manual
4-28
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
polarity selection for the PFI pin for either active high or active low.
Figure 4-25 shows the timing requirements for the UISOURCE signal.
t
p
t
t
w
w
t
= 50 ns minimum
= 10 ns minimum
p
t
w
Figure 4-25. UISOURCE Signal Timing
The maximum allowed frequency is 20 MHz, with a minimum pulse
width of 10 ns high or low. There is no minimum frequency limitation.
Either the 20 MHz or 100 kHz internal timebase normally generates the
UISOURCE signal unless you select some external source.
General-Purpose Timing Signal Connections
The general-purpose timing signals are GPCTR0_SOURCE,
GPCTR0_GATE, GPCTR0_OUT, GPCTR0_UP_DOWN,
GPCTR1_SOURCE, GPCTR1_GATE, GPCTR1_OUT,
GPCTR1_UP_DOWN, and FREQ_OUT.
GPCTR0_SOURCE Signal
Any PFI pin can externally input the GPCTR0_SOURCE signal, which
is available as an output on the PFI8/GPCTR0_SOURCE pin.
As an input, the GPCTR0_SOURCE signal is configured in the
edge-detection mode. You can select any PFI pin as the source for
GPCTR0_SOURCE and configure the polarity selection for either
rising or falling edge.
As an output, the GPCTR0_SOURCE signal reflects the actual clock
connected to general-purpose counter 0. This is true even if another PFI
is externally inputting the source clock. This output is set to tri-state at
startup.
© National Instruments Corporation
4-29
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figure 4-26 shows the timing requirements for the GPCTR0_SOURCE
signal.
t
p
t
t
w
w
t
= 50 ns minimum
= 10 ns minimum
p
t
w
Figure 4-26. GPCTR0_SOURCE Signal Timing
The maximum allowed frequency is 20 MHz, with a minimum pulse
width of 10 ns high or low. There is no minimum frequency limitation.
The 20 MHz or 100 kHz timebase normally generates the
GPCTR0_SOURCE signal unless you select some external source.
GPCTR0_GATE Signal
Any PFI pin can externally input the GPCTR0_GATE signal, which is
available as an output on the PFI9/GPCTR0_GATE pin.
As an input, the GPCTR0_GATE signal is configured in the
edge-detection mode. You can select any PFI pin as the source for
GPCTR0_GATE and configure the polarity selection for either rising or
falling edge. You can use the gate signal in a variety of different
applications to perform actions such as starting and stopping the
counter, generating interrupts, saving the counter contents, and so on.
As an output, the GPCTR0_GATE signal reflects the actual gate signal
connected to general-purpose counter 0. This is true even if the gate is
being externally generated by another PFI. This output is set to tri-state
at startup.
PCI-6110E/6111E User Manual
4-30
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
Figure 4-27 shows the timing requirements for the GPCTR0_GATE
signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-27. GPCTR0_GATE Signal Timing in Edge-Detection Mode
GPCTR0_OUT Signal
This signal is available only as an output on the GPCTR0_OUT pin.
The GPCTR0_OUT signal reflects the terminal count (TC) of
general-purpose counter 0. You have two software-selectable output
options—pulse on TC and toggle output polarity on TC. The output
polarity is software selectable for both options. This output is set to
tri-state at startup. Figure 4-28 shows the timing of the GPCTR0_OUT
signal.
TC
GPCTR0_SOURCE
GPCTR0_OUT
(Pulse on TC)
GPCTR0_OUT
(Toggle output on TC)
Figure 4-28. GPCTR0_OUT Signal Timing
GPCTR0_UP_DOWN Signal
This signal can be externally input on the DIO6 pin and is not available
as an output on the I/O connector. The general-purpose counter 0 will
count down when this pin is at a logic low and count up when it is at a
logic high. You can disable this input so that software can control the
up-down functionality and leave the DIO6 pin free for general use.
© National Instruments Corporation
4-31
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
GPCTR1_SOURCE Signal
Any PFI pin can externally input the GPCTR1_SOURCE signal, which
is available as an output on the PFI3/GPCTR1_SOURCE pin.
As an input, the GPCTR1_SOURCE signal is configured in the
edge-detection mode. You can select any PFI pin as the source for
GPCTR1_SOURCE and configure the polarity selection for either
rising or falling edge.
As an output, the GPCTR1_SOURCE monitors the actual clock
connected to general-purpose counter 1. This is true even if the source
clock is being externally generated by another PFI. This output is set to
tri-state at startup.
Figure 4-29 shows the timing requirements for the GPCTR1_SOURCE
signal.
t
p
t
t
w
w
t
= 50 ns minimum
= 10 ns minimum
p
t
w
Figure 4-29. GPCTR1_SOURCE Signal Timing
The maximum allowed frequency is 20 MHz, with a minimum pulse
width of 10 ns high or low. There is no minimum frequency limitation.
The 20 MHz or 100 kHz timebase normally generates the
GPCTR1_SOURCE unless you select some external source.
GPCTR1_GATE Signal
Any PFI pin can externally input the GPCTR1_GATE signal, which is
available as an output on the PFI4/GPCTR1_GATE pin.
As an input, the GPCTR1_GATE signal is configured in edge-detection
mode. You can select any PFI pin as the source for GPCTR1_GATE and
configure the polarity selection for either rising or falling edge. You can
use the gate signal in a variety of different applications to perform such
PCI-6110E/6111E User Manual
4-32
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
actions as starting and stopping the counter, generating interrupts,
saving the counter contents, and so on.
As an output, the GPCTR1_GATE signal monitors the actual gate
signal connected to general-purpose counter 1. This is true even if the
gate is being externally generated by another PFI. This output is set to
tri-state at startup.
Figure 4-30 shows the timing requirements for the GPCTR1_GATE
signal.
t
w
Rising-edge
polarity
Falling-edge
polarity
t
= 10 ns minimum
w
Figure 4-30. GPCTR1_GATE Signal Timing in Edge-Detection Mode
GPCTR1_OUT Signal
This signal is available only as an output on the GPCTR1_OUT pin.
The GPCTR1_OUT signal monitors the TC board general-purpose
counter 1. You have two software-selectable output options—pulse on
TC and toggle output polarity on TC. The output polarity is software
selectable for both options. This output is set to tri-state at startup.
Figure 4-31 shows the timing requirements for the GPCTR1_OUT
signal.
TC
GPCTR1_SOURCE
GPCTR1_OUT
(Pulse on TC)
GPCTR1_OUT
(Toggle output on TC)
Figure 4-31. GPCTR1_OUT Signal Timing
© National Instruments Corporation
4-33
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
GPCTR1_UP_DOWN Signal
This signal can be externally input on the DIO7 pin and is not available
as an output on the I/O connector. General-purpose counter 1 counts
down when this pin is at a logic low and counts up at a logic high.
This input can be disabled so that software can control the up-down
functionality and leave the DIO7 pin free for general use. Figure 4-32
shows the timing requirements for the GATE and SOURCE input
signals and the timing specifications for the 611X E board OUT output
signals.
tsc
tsp
tsp
V
IH
SOURCE
VIL
tgsu
tgh
V
IH
IL
GATE
OUT
V
tgw
tout
V
V
OH
OL
Source Clock Period
Source Pulse Width
Gate Setup Time
Gate Hold Time
tsc
50 ns minimum
23 ns minimum
10 ns minimum
0 ns minimum
10 ns minimum
80 ns maximum
tsp
tgsu
tgh
tgw
tout
Gate Pulse Width
Output Delay Time
Figure 4-32. GPCTR Timing Summary
The GATE and OUT signal transitions shown in Figure 4-32 are
referenced to the rising edge of the SOURCE signal. This timing
diagram assumes that the counters are programmed to count rising
edges. The same timing diagram, but with the source signal inverted
and referenced to the falling edge of the source signal, would apply
when the counter is programmed to count falling edges.
The GATE input timing parameters are referenced to the signal at the
SOURCE input or to one of the internally generated signals on the
611X E board. Figure 4-32 shows the GATE signal referenced to the
rising edge of a source signal. The gate must be valid (either high or
PCI-6110E/6111E User Manual
4-34
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
low) for at least 10 ns before the rising or falling edge of a source signal
for the gate to take effect at that source edge, as shown by t and t
gsu
gh
in Figure 4-32. The gate signal is not required to be held after the active
edge of the source signal.
If you use an internal timebase clock, the gate signal cannot be
synchronized with the clock. In this case, gates applied close to a source
arrangement results in an uncertainty of one source clock period with
respect to unsynchronized gating sources.
The OUT output timing parameters are referenced to the signal at the
SOURCE input or to one of the internally generated clock signals on the
611X E board. Figure 4-32 shows the OUT signal referenced to the
rising edge of a source signal. Any OUT signal state changes occur
within 80 ns after the rising or falling edge of the source signal.
FREQ_OUT Signal
This signal is available only as an output on the FREQ_OUT pin. The
frequency generator for the 611X E board outputs the FREQ_OUT pin.
The frequency generator is a 4-bit counter that can divide its input clock
by the numbers 1 through 16. The input clock of the frequency
generator is software-selectable from the internal 10 MHz and 100 kHz
timebases. The output polarity is software selectable. This output is set
to tri-state at startup.
Field Wiring Considerations
Environmental noise can seriously affect the accuracy of measurements
made with the 611X E board if you do not take proper care when
running signal wires between signal sources and the board. The
following recommendations apply mainly to analog input signal routing
to the board, although they also apply to signal routing in general.
Minimize noise pickup and maximize measurement accuracy by taking
the following precautions:
•
Use differential analog input connections to reject common-mode
noise.
•
Use individually shielded, twisted-pair wires to connect analog
input signals to the board. With this type of wire, the signals
attached to the ACH+ and ACH– inputs are twisted together and
then covered with a shield. You then connect this shield only at one
© National Instruments Corporation
4-35
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Signal Connections
point to the signal source ground. This kind of connection is
required for signals traveling through areas with large magnetic
fields or high electromagnetic interference.
•
Route signals to the board carefully. Keep cabling away from noise
sources. The most common noise source in a PCI data acquisition
system is the video monitor. Separate the monitor from the analog
signals as much as possible.
The following recommendations apply for all signal connections to the
611X E board:
•
Separate the 611X E board signal lines from high-current or
high-voltage lines. These lines can induce currents in or voltages on
the 611X E board signal lines if they run in parallel paths at a close
distance. To reduce the magnetic coupling between lines, separate
them by a reasonable distance if they run in parallel, or run the lines
at right angles to each other.
•
•
Do not run signal lines through conduits that also contain power
lines.
Protect signal lines from magnetic fields caused by electric motors,
welding equipment, breakers, or transformers by running them
through special metal conduits.
For more information, refer to the application note, Field Wiring and
Noise Consideration for Analog Signals, available from National
Instruments.
PCI-6110E/6111E User Manual
4-36
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
5
Calibration
This chapter discusses the calibration procedures for your 611X E
board. If you are using the NI-DAQ device driver, that software
includes calibration functions for performing all of the steps in the
calibration process.
Calibration refers to the process of minimizing measurement and output
voltage errors by making small circuit adjustments. On the 611X E
board, these adjustments take the form of writing values to onboard
calibration DACs (CalDACs).
Some form of board calibration is required for all but the most forgiving
applications. If you do not calibrate your board, your signals and
measurements could have very large offset, gain, and linearity errors.
Three levels of calibration are available to you and described in this
chapter. The first level is the fastest, easiest, and least accurate;
whereas, the last level is the slowest, most difficult, and most accurate.
Loading Calibration Constants
The 611X E board is factory calibrated before shipment at
approximately 25° C to the levels indicated in Appendix A,
Specifications. The associated calibration constants—the values that
were written to the CalDACs to achieve calibration in the factory—are
stored in the onboard nonvolatile memory (EEPROM). Because the
CalDACs have no memory capability, they do not retain calibration
information when the board is unpowered. Loading calibration
constants refers to the process of loading the CalDACs with the values
stored in the EEPROM. NI-DAQ software determines when this is
necessary and does it automatically. If you are not using NI-DAQ,
you must load these values yourself.
In the EEPROM there is a user-modifiable calibration area in addition
to the permanent factory calibration area. This means that you can load
the CalDACs with values either from the original factory calibration or
from a calibration that you subsequently performed.
© National Instruments Corporation
5-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Calibration
This method of calibration is not very accurate because it does not take
into account the fact that the board measurement and output voltage
errors can vary with time and temperature. It is better to self-calibrate
when the board is installed in the environment in which it will be used.
Self-Calibration
The 611X E board can measure and correct for almost all of its
calibration-related errors without any external signal connections. Your
National Instruments software provides a self-calibration method. This
self-calibration process, which generally takes less than a minute, is
the preferred method of assuring accuracy in your application. Initiate
self-calibration to minimize the effects of any offset, gain, and linearity
drifts, particularly those due to warmup.
Immediately after self-calibration, the only significant residual
calibration error could be gain error due to time or temperature drift
of the onboard voltage reference. This error is addressed by external
calibration, which is discussed in the following section. If you are
interested primarily in relative measurements, you can ignore a small
amount of gain error, and self-calibration should be sufficient.
External Calibration
The 611X E board has an onboard calibration reference to ensure the
accuracy of self-calibration. Its specifications are listed in Appendix A,
Specifications. The reference voltage is measured at the factory and
stored in the EEPROM for subsequent self-calibrations. This voltage is
stable enough for most applications, but if you are using your board at
an extreme temperature or if the onboard reference has not been
measured for a year or more, you may wish to externally calibrate your
board.
An external calibration refers to calibrating your board with a known
external reference rather than relying on the onboard reference.
Redetermining the value of the onboard reference is part of this process
and the results can be saved in the EEPROM, so you should not have to
perform an external calibration very often. You can externally calibrate
your board by calling the NI-DAQ calibration function.
PCI-6110E/6111E User Manual
5-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Calibration
To externally calibrate your board, be sure to use a very accurate
external reference. The reference should be several times more accurate
than the board itself. For example, to calibrate a 16-bit board, the
external reference should be at least ±0.001% (±10 ppm) accurate.
© National Instruments Corporation
5-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
A
Specifications
This appendix lists the specifications of your 611X E board. These
specifications are typical at 25° C unless otherwise noted.
PCI-6110E/6111E
Analog Input
Input Characteristics
Number of channels
PCI-6110E ...................................4 differential
PCI-6111E ...................................2 differential
Resolution...........................................12 bits, 1 in 4,096
Max sampling rate ..............................5 MS/s
Min sampling rate ...............................1 kS/s
Analog input characteristics
Input Range
±50 V
Gain Error1
Offset Error
10 mV
SFDR2
70 dB
70 dB
75 dB
75 dB
75 dB
75 dB
75 dB
75 dB
CMRR3
32 dB
35 dB
50 dB
56 dB
62 dB
67 dB
70 dB
72 dB
System Noise4
0.50%
0.5
0.5
0.5
0.5
0.5
0.5
0.6
1.0
±20 V
0.50%
10 mV
±10 V
0.10%
0.8 mV
±5 V
0.05%
0.5 mV
±2 V
0.05%
0.28 mV
0.20 mV
0.15 mV
0.10 mV
±1 V
0.05%
±500 mV
±200 mV
0.05%
0.05%
1Relative to reading, max
2All input ranges, DC to 100 kHz
3All input ranges, DC to 60 Hz
4LSBrms, not including quantization
© National Instruments Corporation
A-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Input coupling .................................... DC/AC
Max working voltage for all analog input channels
+ input ......................................... Should remain within ±11 V for
ranges ≥ ±10 V; should remain
within ±42 V for ranges < ±10 V
– input ......................................... Should remain within ±11 V
Overvoltage protection....................... ±42 V
Inputs protected
+ input ......................................... all channels
– input ......................................... all channels
FIFO buffer size................................. 8,192 samples
Data transfers ..................................... DMA, interrupts,
programmed I/O
DMA modes....................................... Scatter-gather
Accuracy Information
See following table
PCI-6110E/6111E User Manual
A-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
© National Instruments Corporation
A-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Transfer Characteristics
INL .................................................... ±0.5 LSB typ, ±1 LSB max
DNL................................................... ±0.3 LSB typ, ±0.75 LSB max
Spurious free dynamic range (SFDR). See table, analog input
characteristics
Effective number of bits (ENOB)....... 11.0 bits, DC to 100 kHz
Offset error ........................................ See table, analog input
characteristics
Amplifier Characteristics
Input impedance................................. 1 MΩ in parallel with 100 pF
Input bias current ............................... ±200 pA
Input offset current............................. ±100 pA
CMRR................................................ See table, analog input
characteristics
Dynamic Characteristics
Interchannel skew .............................. 1 ns typ
f
= 100 kHz
in
input range = ±10 V
Bandwidth (0.5 to –3 dB)
Input range > ±0.2 V ................... 5 MHz
Input range = ±0.2 V ................... 4 MHz
System noise ...................................... See table, analog input
characteristics
Crosstalk ............................................ –80 dB, DC to 100 kHz
Stability
Recommended warm-up time ............. 15 min.
Offset temperature coefficient
Pregain ........................................ ±5 µV/° C
PCI-6110E/6111E User Manual
A-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Postgain .......................................±50 µV/° C
Gain temperature coefficient...............±20 ppm/° C
Onboard calibration reference
Level ............................................5.000 V (±2.5 mV) (actual
value stored in EEPROM)
Temperature coefficient ...............±0.6 ppm/° C max
Long-term stability.......................±6 ppm/ 1, 000 h
Analog Output
Output Characteristics
Number of channels ............................2 voltage
Resolution...........................................16 bits, 1 in 65,536
Max update rate
1 channel......................................4 MS/s, system dependent
2 channel......................................2.5 MS/s, system dependent
FIFO buffer size..................................2,048 samples
Data transfers......................................DMA, interrupts,
programmed I/O
DMA modes .......................................Scatter gather
Transfer Characteristics
Relative accuracy (INL)......................±4 LSB typ, ±8 LSB max
DNL....................................................±2 LSB typ, ±8 LSB max
Offset error .........................................±5.0 mV max
Gain error
(relative to internal reference).............±0.1% of output range max
Voltage Output
Ranges ................................................±10 V
Output coupling ..................................DC
© National Instruments Corporation
A-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Output impedance .............................. 50 Ω ±5%
Current drive ...................................... ±5 mA min
Output stability .................................. Any passive load
Protection .......................................... Short-circuit to ground
Power-on state.................................... 0 V
Dynamic Characteristics
Slew rate ............................................ 300 V/µs
Noise.................................................. 1 mV , DC to 5 MHz
rms
Spurious free dynamic range .............. 75 dB, DC to 10 kHz
Stability
Offset temperature coefficient............ ±500 µV/° C
Gain temperature coefficient
Internal reference......................... ±50 ppm/° C
External reference ....................... ±25 ppm/° C
Onboard calibration reference
Level ........................................... 5.000 V (±2.5 mV) (actual
value stored in EEPROM)
Temperature coefficient............... ±0.6 ppm/° C max
Long-term stability ...................... ±6 ppm/ 1, 000 h
Digital I/O
Number of channels ........................... 8 input/output
Compatibility ..................................... TTL/CMOS
PCI-6110E/6111E User Manual
A-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Digital logic levels
Level
Min
Max
Input low voltage
Input high voltage
0.0 V
2.0 V
—
0.8 V
5.0 V
Input low current (V = 0 V)
–320 µA
10 µA
in
Input high current (V = 5 V)
—
in
Output low voltage (I = 24 mA)
—
0.4 V
—
OL
Output high voltage (I = 13 mA)
4.35 V
OH
Power-on state ....................................Input (High-Z)
Data transfers......................................Programmed I/O
Timing I/O
Number of channels ............................2 up/down counter/timers,
1 frequency scaler
Resolution
Counter/timers .............................24 bits
Frequency scaler ..........................4 bits
Compatibility......................................TTL/CMOS
Base clocks available
Counter/timers .............................20 MHz, 100 kHz
Frequency scaler ..........................10 MHz, 100 kHz
Base clock accuracy............................±0.01%
Max source frequency.........................20 MHz
Min source pulse duration ..................10 ns, edge-detect mode
Min gate pulse duration .....................10 ns, edge-detect mode
© National Instruments Corporation
A-7
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Data transfers ..................................... DMA, interrupts,
programmed I/O
DMA modes....................................... Scatter-gather
Triggers
Analog Trigger
Source
PCI-6110E................................... All analog input channels,
external trigger (PFI0/TRIG1)
PCI-6111E................................... All analog input channels,
external trigger (PFI0/TRIG1)
Level .................................................. ± full-scale, internal;
±10 V, external
Slope .................................................. Positive or negative
(software selectable)
Resolution .......................................... 8 bits, 1 in 256
Hysteresis........................................... Programmable
Bandwidth ......................................... (–3 dB) 5 MHz internal/external
External input (PFI0/TRIG1)
Impedance ................................... 10 kΩ
Coupling...................................... AC/DC
Protection .................................... –0.5 V to (V + 0.5) V when
cc
configured as a digital signal,
±35 V when configured as an
analog trigger signal or
disabled, ±35 V powered off
Digital Trigger
Compatibility ..................................... TTL
Response ............................................ Rising or falling edge
Pulse width......................................... 10 ns min
PCI-6110E/6111E User Manual
A-8
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
RTSI
Trigger Lines ......................................7
Bus Interface
Type ...................................................Master, slave
Power Requirement
+5 VDC (±5%)
PCI-6110E ...................................2.5 A
PCI-6111E ...................................2.0 A
Power available at I/O connector ........+4.65 to +5.25 VDC at 1 A
Physical
Dimensions
(not including connectors) .................31.2 by 10.6 cm (12.3 by 4.2 in)
I/O connector ......................................68-pin male SCSI-II type
Environment
Operating temperature ........................0° to 45° C
Storage temperature ............................–20° to 70° C
Relative humidity ...............................5% to 90% noncondensing
© National Instruments Corporation
A-9
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Cable Connector
Descriptions
B
This appendix describes the cable connectors on your 611X E board.
Figure B-1 shows the pin assignments for the 68-pin 611X E connector.
This connector is available when you use the SH6868EP cable
assemblies with the 611X E board.
© National Instruments Corporation
B-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Cable Connector Descriptions
34 68
ACH1+ 33 67
ACH0–
ACH0+
ACH0GND
ACH1–
ACH2+1
ACH2GND1
ACH3–1
NC
32 66
31 65
30 64
29 63
28 62
ACH1GND
ACH2–1
ACH3+1
ACH3GND1
NC
NC 27 61
NC 26 60
NC
NC
NC
NC 24 58
25 59
NC
NC
NC
23 57
22 56
21 55
NC
NC
DAC0OUT
DAC1OUT
AOGND
AOGND
DGND
DIO0
NC 20 54
19 53
18 52
17 51
16 50
15 49
DIO4
DGND
DIO1
DIO5
DIO6
DGND
DIO2
DGND
+5 V 14 48
DGND 13 47
DGND 12 46
DIO7
DIO3
SCANCLK
PFI0/TRIG1
11 45
10 44
EXTSTROBE*
DGND
PFI1/TRIG2
DGND
9
8
7
6
5
4
3
2
1
43
42
41
40
39
38
37
36
35
PFI2/CONVERT*
PFI3/GPCTR1_SOURCE
PFI4/GPCTR1_GATE
GPCTR1_OUT
DGND
+5 V
DGND
PFI5/UPDATE*
PFI6/WFTRIG
DGND
PFI7/STARTSCAN
PFI8/GPCTR0_SOURCE
DGND
PFI9/GPCTR0_GATE
GPCTR0_OUT
FREQ_OUT
DGND
1 NC on PCI-6111E
Figure B-1. 68-Pin 611X E Series Connector Pin Assignments
PCI-6110E/6111E User Manual
B-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
C
Common Questions
This appendix contains a list of commonly asked questions and their
answers relating to usage and special features of your 611X E board.
General Information
What is the 611X E board?
The 611X E board is a switchless and jumperless enhanced MIO board
that uses the DAQ-STC for timing.
What is the DAQ-STC?
The DAQ-STC is the system timing control application-specific
integrated circuit (ASIC) designed by National Instruments and is the
backbone of the 611X E board. The DAQ-STC contains seven 24-bit
counters and three 16-bit counters. The counters are divided into the
following three groups:
•
•
•
Analog input—two 24-bit, two 16-bit counters
Analog output—three 24-bit, one 16-bit counters
General-purpose counter/timer functions—two 24-bit counters
The groups can be configured independently with timing resolutions of
50 ns or 10 µs. With the DAQ-STC, you can interconnect a wide variety
of internal timing signals to other internal blocks. The interconnection
scheme is quite flexible and completely software configurable. New
capabilities such as buffered pulse generation, equivalent time
sampling, and seamlessly changing the sampling rate are possible.
What does sampling rate mean to me?
It means that this is the fastest you can acquire data on your board and
still achieve accurate results. The 611X E board has a sampling rate of
5 MS/s. This sampling rate is at 5 MS/s regardless if 1 or 4 channels are
acquiring data.
© National Instruments Corporation
C-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Common Questions
What type of 5 V protection does the 611X E board have?
The 611X E board has 5 V lines equipped with a self-resetting 1 A fuse.
Installation and Configuration
How do you set the base address for the 611X E board?
The base address of the 611X E board is assigned automatically through
the PCI bus protocol. This assignment is completely transparent to you.
What jumpers should I be aware of when configuring my
611X E board?
The 611X E board is jumperless and switchless.
Which National Instruments document should I read first to get
started using DAQ software?
Your NI-DAQ or application software release notes documentation is
always the best starting place.
Analog Input and Output
I have connected a differential input signal, but my readings are
random and drift rapidly. What’s wrong?
referenced to a level that is considered floating with reference to the
board ground reference. Even if you are in differential mode, the signal
must still be referenced to the same ground level as the board reference.
There are various methods of achieving this while maintaining a high
common-mode rejection ratio (CMRR). These methods are outlined in
Chapter 4, Signal Connections.
I’m using the DACs to generate a waveform, but I discovered with
a digital oscilloscope that there are glitches on the output signal. Is
this normal?
When it switches from one voltage to another, any DAC produces
glitches due to released charges. The largest glitches occur when the
most significant bit (MSB) of the D/A code switches. You can build a
lowpass deglitching filter to remove some of these glitches, depending
on the frequency and nature of your output signal.
PCI-6110E/6111E User Manual
C-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Common Questions
Can I synchronize a one-channel analog input data acquisition with
a one-channel analog output waveform generation on my
611X E board?
Yes. One way to accomplish this is to use the waveform generation
timing pulses to control the analog input data acquisition. To do this,
follow steps 1 through 4 below, in addition to the usual steps for data
acquisition and waveform generation configuration.
1. Enable the PFI5 line for output, as follows:
•
If you are using NI-DAQ, call
Select_Signal(deviceNumber, ND_PFI_5,
ND_OUT_UPDATE, ND_HIGH_TO_LOW).
•
If you are using LabVIEW, invoke Route Signal VI with signal
name set to PFI5 and signal source set to AO Update.
2. Set up data acquisition timing so that the timing signal for A/D
conversion comes from PFI5, as follows:
•
If you are using NI-DAQ, call
Select_Signal(deviceNumber, ND_IN_CONVERT,
ND_PFI_5, ND_HIGH_TO_LOW).
•
If you are using LabVIEW, invoke AI Clock Config VI with
clock source code set to PFI pin, high to low, and clock source
string set to 5.
3. Initiate analog input data acquisition, which will start only when
the analog output waveform generation starts.
4. Initiate analog output waveform generation.
Timing and Digital I/O
What types of triggering can be hardware-implemented on my
611X E board?
Hardware digital and analog triggering are both supported on the
611X E board.
What added functionality does the DAQ-STC make possible in
contrast to the Am9513?
The DAQ-STC incorporates much more than just 10 Am9513-style
counters within one chip. In fact, the DAQ-STC has the complexity of
more than 24 chips. The DAQ-STC makes possible PFI lines, analog
triggering, selectable logic level, and frequency shift keying. The
DAQ-STC also makes buffered operations possible, such as direct
© National Instruments Corporation
C-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Common Questions
up/down control, single or pulse train generation, equivalent time
sampling, buffered period, and buffered semiperiod measurement.
What is the difference in timebases between the Am9513
counter/timer and the DAQ-STC?
The DAQ-STC-based MIO boards have a 20 MHz timebase. The
Am9513-based MIO boards have a 1 MHz or 5 MHz timebase.
Will the counter/timer applications that I wrote previously, work
with the DAQ-STC?
If you are using NI-DAQ with LabVIEW, some of your applications
drawn using the CTR VIs will still run. However, there are many
differences in the counters between the 611X E and other boards; the
counter numbers are different, timebase selections are different, and the
DAQ-STC counters are 24-bit counters (unlike the 16-bit counters on
boards without the DAQ-STC).
If you are using the NI-DAQ language interface or LabWindows/CVI,
the answer is no, the counter/timer applications that you wrote
previously will not work with the DAQ-STC. You must use the GPCTR
functions; ICTR and CTR functions will not work with the DAQ-STC.
The GPCTR functions have the same capabilities as the ICTR and CTR
functions, plus more, but you must rewrite the application with the
GPCTR function calls.
I’m using one of the general-purpose counter/timers on my
611X E board, but I do not see the counter/timer output on the I/O
connector. What am I doing wrong?
If you are using the NI-DAQ language interface or LabWindows/CVI,
you must configure the output line to output the signal to the I/O
connector. Use the Select_Signalcall in NI-DAQ to configure the
output line. By default, all timing I/O lines except EXTSTROBE* are
tri-stated.
What are the PFIs and how do I configure these lines?
PFIs are Programmable Function Inputs. These lines serve as
connections to virtually all internal timing signals.
If you are using the NI-DAQ language interface or LabWindows/CVI,
use the Select_Signalfunction to route internal signals to the I/O
PCI-6110E/6111E User Manual
C-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Common Questions
connector, route external signals to internal timing sources, or tie
internal timing signals together.
If you are using NI-DAQ with LabVIEW and you want to connect
external signal sources to the PFI lines, you can use AI Clock Config,
AI Trigger Config, AO Clock Config, AO Trigger and Gate Config,
CTR Mode Config, and CTR Pulse Config advanced level VIs to
indicate which function the connected signal will serve. Use the Route
Signal VI to enable the PFI lines to output internal signals.
Caution: If you enable a PFI line for output, do not connect any external signal
source to it; if you do, you can damage the board, the computer, and the
connected equipment.
!
What are the power-on states of the PFI and DIO lines on the I/O
connector?
impedance by the hardware. This means that the board circuitry is not
actively driving the output either high or low. However, these lines may
have pull-up or pull-down resistors connected to them as shown in
Table 4-2. These resistors weakly pull the output to either a logic high
or logic low state. For example, DIO(0) will be in the high impedance
state after power on, and Table 4-2 shows that there is a 50 kΩ pull-up
resistor. This pull-up resistor will set the DIO(0) pin to a logic high
when the output is in a high impedance state.
© National Instruments Corporation
C-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
D
Customer Communication
For your convenience, this appendix contains forms to help you gather the information necessary
to help us solve your technical problems and a form you can use to comment on the product
documentation. When you contact us, we need the information on the Technical Support Form and
the configuration form, if your manual contains one, about your system configuration to answer your
questions as quickly as possible.
National Instruments has technical assistance through electronic, fax, and telephone systems to quickly
provide the information you need. Our electronic services include a bulletin board service, an FTP site,
a fax-on-demand system, and e-mail support. If you have a hardware or software problem, first try the
electronic support systems. If the information available on these systems does not answer your
questions, we offer fax and telephone support through our technical support centers, which are staffed
by applications engineers.
Electronic Services
Bulletin Board Support
National Instruments has BBS and FTP sites dedicated for 24-hour support with a collection of files
and documents to answer most common customer questions. From these sites, you can also download
the latest instrument drivers, updates, and example programs. For recorded instructions on how to use
the bulletin board and FTP services and for BBS automated information, call 512 795 6990. You can
access these services at:
United States: 512 794 5422
Up to 14,400 baud, 8 data bits, 1 stop bit, no parity
United Kingdom: 01635 551422
Up to 9,600 baud, 8 data bits, 1 stop bit, no parity
France: 01 48 65 15 59
Up to 9,600 baud, 8 data bits, 1 stop bit, no parity
FTP Support
To access our FTP site, log on to our Internet host, ftp.natinst.com, as anonymousand use
documents are located in the /supportdirectories.
© National Instruments Corporation
D-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax-on-Demand Support
Fax-on-Demand is a 24-hour information retrieval system containing a library of documents on a wide
range of technical information. You can access Fax-on-Demand from a touch-tone telephone at
512 418 1111.
E-Mail Support (Currently USA Only)
You can submit technical support questions to the applications engineering team through e-mail at the
Internet address listed below. Remember to include your name, address, and phone number so we can
contact you with solutions and suggestions.
Telephone and Fax Support
National Instruments has branch offices all over the world. Use the list below to find the technical
support number for your country. If there is no National Instruments office in your country, contact
the source from which you purchased your software to obtain support.
Country
Telephone
Fax
Australia
Austria
Belgium
Brazil
Canada (Ontario)
Canada (Québec)
Denmark
Finland
03 9879 5166
0662 45 79 90 0
02 757 00 20
011 288 3336
905 785 0085
514 694 8521
45 76 26 00
09 725 725 11
01 48 14 24 24
089 741 31 30
2645 3186
03 6120092
02 413091
03 5472 2970
02 596 7456
5 520 2635
03 9879 6277
0662 45 79 90 19
02 757 03 11
011 288 8528
905 785 0086
514 694 4399
45 76 26 02
09 725 725 55
01 48 14 24 14
089 714 60 35
2686 8505
France
Germany
Hong Kong
Israel
Italy
Japan
03 6120095
02 41309215
03 5472 2977
02 596 7455
5 520 3282
Korea
Mexico
Netherlands
Norway
Singapore
Spain
Sweden
Switzerland
Taiwan
0348 433466
32 84 84 00
2265886
91 640 0085
08 730 49 70
056 200 51 51
02 377 1200
01635 523545
512 795 8248
0348 430673
32 84 86 00
2265887
91 640 0533
08 730 43 70
056 200 51 55
02 737 4644
01635 523154
512 794 5678
United Kingdom
United States
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support Form
Photocopy this form and update it each time you make changes to your software or hardware, and use
the completed copy of this form as a reference for your current configuration. Completing this form
accurately before contacting National Instruments for technical support helps our applications
engineers answer your questions more efficiently.
If you are using any National Instruments hardware or software products related to this problem,
include the configuration forms from their user manuals. Include additional pages if necessary.
Name __________________________________________________________________________
Company _______________________________________________________________________
Address ________________________________________________________________________
_______________________________________________________________________________
Fax (___)___________________ Phone (___) _________________________________________
Computer brand ________________ Model ________________ Processor___________________
Operating system (include version number) ____________________________________________
Clock speed ______MHz RAM _____MB
Mouse ___yes ___no Other adapters installed _______________________________________
Hard disk capacity _____MB Brand _____________________________________________
Display adapter __________________________
Instruments used _________________________________________________________________
_______________________________________________________________________________
National Instruments hardware product model __________ Revision ______________________
Configuration ___________________________________________________________________
National Instruments software product ____________________________Version ____________
Configuration ___________________________________________________________________
The problem is: __________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
List any error messages: ___________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
The following steps reproduce the problem:____________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI-6110E/6111E Hardware and Software
Configuration Form
Record the settings and revisions of your hardware and software on the line to the right of each item.
Complete a new copy of this form each time you revise your software or hardware configuration, and
use this form as a reference for your current configuration. Completing this form accurately before
contacting National Instruments for technical support helps our applications engineers answer your
questions more efficiently.
National Instruments Products
PCI-6110E/6111E board ___________________________________________________________
PCI-6110E/6111E board serial number _______________________________________________
Base memory address of the PCI-6110E/6111E board ___________________________________
Interrupt level of the PCI-6110E/6111E board __________________________________________
National Instruments application software choice ________________________________________
Software version __________________________________________________________________
Other Products
Computer make and model _________________________________________________________
Microprocessor ___________________________________________________________________
Clock frequency or speed ___________________________________________________________
Type of video board installed ________________________________________________________
Operating system (DOS or Windows) _________________________________________________
Operating system version ___________________________________________________________
Operating system mode ____________________________________________________________
Programming language ____________________________________________________________
Programming language version ______________________________________________________
Other boards in system _____________________________________________________________
Base memory address of other boards _________________________________________________
Interrupt level of other boards _______________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Documentation Comment Form
National Instruments encourages you to comment on the documentation supplied with our products.
This information helps us provide quality products to meet your needs.
Title:
PCI-6110E/6111E User Manual
Edition Date: April 1998
Part Number: 321759B-01
Please comment on the completeness, clarity, and organization of the manual.
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
If you find errors in the manual, please record the page numbers and describe the errors.
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
Thank you for your help.
Name _________________________________________________________________________
Title __________________________________________________________________________
Company _______________________________________________________________________
Address ________________________________________________________________________
_______________________________________________________________________________
Phone (___)__________________________ Fax (___)___________________________________
Mail to: Technical Publications
National Instruments Corporation
Fax to: Technical Publications
National Instruments Corporation
(512) 794-5678
6504 Bridge Point Parkway
Austin, TX 78730-5039
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Prefix
p-
Meaning
pico-
Value
10–12
10–9
10–6
10–3
103
n-
nano-
micro-
milli-
kilo-
µ-
m-
k-
M-
G-
mega-
giga-
106
109
Symbols/Numbers
°
degrees
greater than
>
≥
<
≤
/
greater than or equal to
less than
less than or equal to
per
%
±
+
percent
plus or minus
positive of, or plus
© National Instruments Corporation
G-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
–
negative of, or minus
ohms
Ω
square root of
+5 V
+5 VDC source signal
A
A
amperes
AC
alternating current
ACH
ACH0GND
A/D
analog input channel signal
analog input channel ground signal
analog-to-digital
ADC
analog-to-digital converter—an electronic device, often an
integrated circuit, that converts an analog voltage to a digital
number
AI
analog input
AIGATE
AIGND
ANSI
AO
analog input gate signal
analog input ground signal
American National Standards Institute
analog output
AOGND
ASIC
analog output ground signal
Application-Specific Integrated Circuit—a proprietary
semiconductor component designed and manufactured to perform
a set of specific functions.
B
bipolar
a signal range that includes both positive and negative values
(for example, –5 V to +5 V)
PCI-6110E/6111E User Manual
G-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
C
C
Celsius
CalDAC
CH
calibration DAC
channel—pin or wire lead to which you apply or from which you
read the analog or digital signal. Analog signals can be single-
ended or differential. For digital signals, you group channels to
form ports. Ports usually consist of either four or eight digital
channels
cm
centimeter
CMOS
CMRR
complementary metal-oxide semiconductor
common-mode rejection ratio—a measure of an instrument’s
ability to reject interference from a common-mode signal, usually
expressed in decibels (dB)
CONVERT*
counter/timer
CTR
convert signal
a circuit that counts external pulses or clock pulses (timing)
counter
D
D/A
digital-to-analog
DAC
digital-to-analog converter—an electronic device, often an
integrated circuit, that converts a digital number into a
corresponding analog voltage or current
DAC0OUT
DAC1OUT
DAQ
analog channel 0 output signal
analog channel 1 output signal
data acquisition—a system that uses the computer to collect,
receive, and generate electrical signals
DAQ-STC
Data acquisition system timing controller. An application-specific
integrated circuit (ASIC) for the system timing requirements of a
© National Instruments Corporation
G-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
general A/D and D/A system, such as a system containing the
National Instruments E Series boards.
dB
decibel—the unit for expressing a logarithmic measure of the ratio
of two signal levels: dB=20log10 V1/V2, for signals in volts
DC
direct current
DGND
DI
digital ground signal
digital input
DIFF
DIO
differential mode
digital input/output
DIP
dual inline package
dithering
DMA
the addition of Gaussian noise to an analog input signal
direct memory access—a method by which data can be transferred
to/from computer memory from/to a device or memory on the bus
while the processor does something else. DMA is the fastest
method of transferring data to/from computer memory.
DNL
DO
differential nonlinearity—a measure in least significant bit of the
worst-case deviation of code widths from their ideal value of 1 LSB
digital output
E
EEPROM
electrically erasable programmable read-only memory—ROM that
can be erased with an electrical signal and reprogrammed
EXTSTROBE
external strobe signal
F
FIFO
first-in first-out memory buffer—FIFOs are often used on DAQ
devices to temporarily store incoming or outgoing data until that
data can be read or written. For example, an analog input FIFO
stores the results of A/D conversions until the data can be read into
PCI-6110E/6111E User Manual
G-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
system memory. Programming the DMA controller and servicing
interrupts can take several milliseconds in some cases. During this
time, data accumulates in the FIFO for future retrieval. With a
larger FIFO, longer latencies can be tolerated. In the case of analog
output, a FIFO permits faster update rates, because the waveform
data can be stored in the FIFO ahead of time. This again reduces the
effect of latencies associated with getting the data from system
memory to the DAQ device.
FREQ_OUT
ft
frequency output signal
feet
G
GATE
gate signal
GPCTR
general-purpose counter signal
GPCTR0_GATE
GPCTR0_OUT
GPCTR0_SOURCE
GPCTR0_UP_DOWN
GPCTR1_GATE
GPCTR1_OUT
GPCTR1_SOURCE
GPCTR1_UP_DOWN
general-purpose counter 0 gate signal
general-purpose counter 0 output signal
general-purpose counter 0 clock source signal
general-purpose counter 0 up down signal
general-purpose counter 1 gate signal
general-purpose counter 1 output signal
general-purpose counter 1 clock source signal
general-purpose counter 1 up down signal
H
h
hour
hex
Hz
hexadecimal
hertz
© National Instruments Corporation
G-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
I
INL
integral nonlinearity–For an ADC, deviation of codes of the actual
transfer function from a straight line.
I/O
input/output—the transfer of data to/from a computer system
involving communications channels, operator interface devices,
and/or data acquisition and control interfaces
IOH
IOL
current, output high
current, output low
K
kHz
kilohertz
L
LED
LSB
light emitting diode
least significant bit
M
m
meter
MB
megabytes of memory
megahertz
MHz
MIO
MITE
MSB
mux
multifunction I/O
MXI Interface to Everything
most significant bit
multiplexer—a switching device with multiple inputs that
sequentially connects each of its inputs to its output, typically
at high speeds, in order to measure several signals with a single
analog input channel
PCI-6110E/6111E User Manual
G-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
mV
millivolts
N
NC
normally closed, or not connected
NI-DAQ
noise
National Instruments driver software for DAQ hardware
an undesirable electrical signal—Noise comes from external
sources such as the AC power line, motors, generators,
transformers, fluorescent lights, CRT displays, computers,
electrical storms, welders, radio transmitters, and internal sources
such as semiconductors, resistors, and capacitors. Noise corrupts
signals you are trying to send or receive.
NRSE
nonreferenced single-ended mode—all measurements are made
with respect to a common (NRSE) measurement system reference,
but the voltage at this reference can vary with respect to the
measurement system ground
O
OUT
output pin—a counter output pin where the counter can generate
various TTL pulse waveforms
P
PCI
Peripheral Component Interconnect—a high-performance
expansion bus architecture originally developed by Intel to replace
ISA and EISA. It is achieving widespread acceptance as a standard
for PCs and work-stations; it offers a theoretical maximum transfer
rate of 132 MB/s.
PFI
Programmable Function Input
PFI0/trigger 1
PFI0/TRIG1
PFI1/TRIG2
PFI1/trigger 2
PFI2/CONVERT*
PFI3/GPCTR1_SOURCE
PFI2/convert
PFI3/general purpose counter 1 source
© National Instruments Corporation
G-7
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
PFI4/GPCTR1_GATE
PFI5/UPDATE*
PFI6/WFTRIG
PFI4/general-purpose counter 1 gate
PFI5/update
PFI6/waveform trigger
PFI7/STARTSCAN
PFI8/GPCTR0_SOURCE
PFI9/GPCTR0_GATE
PGIA
PFI7/start of scan
PFI8/general-purpose counter 0 source
PFI9/general-purpose counter 0 gate
Programmable Gain Instrumentation Amplifier
port
(1) a communications connection on a computer or a remote
controller (2) a digital port, consisting of four or eight lines of
digital input and/or output
ppm
pu
parts per million
pull-up
R
RAM
rms
random access memory
root mean square
RSE
referenced single-ended mode—all measurements are made with
respect to a common reference measurement system or a ground.
Also called a grounded measurement system
RTD
resistive temperature detector—a metallic probe that measures
temperature based upon its coefficient of resistivity
RTSIbus
real-time system integration bus—the National Instruments timing
bus that connects DAQ boards directly, by means of connectors on
top of the boards, for precise timing synchronization between
multiple boards
RTSI_OSC
RTSI Oscillator—RTSI bus master clock
PCI-6110E/6111E User Manual
G-8
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
S
s
seconds
S
samples
SCANCLK
SCXI
scan clock signal
Signal Conditioning eXtensions for Instrumentation—the National
Instruments product line for conditioning low-level signals within
an external chassis near sensors so only high-level signals are sent
to DAQ boards in the noisy computer environment
SE
single-ended—a term used to describe an analog input that is
measured with respect to a common ground
settling time
the amount of time required for a voltage to reach its final value
within specified limits
signal conditioning
SISOURCE
SOURCE
the manipulation of signals to prepare them for digitizing
SI counter clock signal
source signal
S/s
samples per second—used to express the rate at which a DAQ
board samples an analog signal
STARTSCAN
system noise
start scan signal
a measure of the amount of noise seen by an analog circuit or an
ADC when the analog inputs are grounded
T
TC
tgh
terminal count—the ending value of a counter
gate hold time
tgsu
tgw
tout
gate setup time
gate pulse width
output delay time
© National Instruments Corporation
G-9
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
THD
total harmonic distortion—the ratio of the total rms signal due to
harmonic distortion to the overall rms signal, in decibel or a
percentage
thermocouple
TRIG
a temperature sensor created by joining two dissimilar metals. The
junction produces a small voltage as a function of the temperature.
trigger signal
t
t
source clock period
source pulse width
transistor-transistor logic
sc
sp
TTL
U
UI
update interval
UISOURCE
unipolar
UPDATE
update interval counter clock signal
a signal range that is always positive (for example, 0 to +10 V)
update signal
V
V
volts
VDC
VI
volts direct current
virtual instrument—(1) a combination of hardware and/or software
elements, typically used with a PC, that has the functionality of a
classic stand-alone instrument (2) a LabVIEW software module
(VI), which consists of a front panel user interface and a block
diagram program
VIH
VIL
Vin
Vm
volts, input high
volts, input low
volts in
measured voltage
PCI-6110E/6111E User Manual
G-10
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
VOH
VOL
Vref
Vrms
volts, output high
volts, output low
reference voltage
volts, root mean square
W
WFTRIG
waveform generation trigger signal
© National Instruments Corporation
G-11
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
nonreferenced or floating signal
sources (figure), 4-12
signal summary (table), 4-6
AIGATE signal, 4-25
amplifier characteristic specifications,
A-3 to A-4
Numbers
+5 V signal
description (table), 4-3
power connections, 4-15
self-resetting fuse, 4-15, C-2
analog input, 3-2 to 3-5
dither, 3-4 to 3-5
input coupling, 3-4
input mode, 3-2 to 3-3
A
AC input coupling, 3-4
ACH<0..3>+ signal
input polarity and range, 3-3 to 3-4
questions about, C-2 to C-3
selection considerations, 3-4
signal connections, 4-8
specifications, A-1 to A-5
amplifier characteristics, A-3 to A-4
dynamic characteristics, A-4
input characteristics, A-1 to A-2
stability, A-4 to A-5
analog input connections, 4-8
description (table), 4-3
differential connections
ground-referenced signal sources
(figure), 4-11
nonreferenced or floating signal
sources (figure), 4-12
signal summary (table), 4-6
ACH<0..3>- signal
transfer characteristics, A-2 to A-3
analog output, 3-5
analog input connections, 4-8
description (table), 4-3
differential connections
ground-referenced signal sources
(figure), 4-11
questions about, C-2 to C-3
signal connections, 4-13
specifications, A-5 to A-6
dynamic characteristics, A-6
output characteristics, A-5
stability, A-6
nonreferenced or floating signal
sources (figure), 4-12
signal summary (table), 4-6
ACH<0..3>GND signal
description (table), 4-3
differential connections
ground-referenced signal sources
(figure), 4-11
transfer characteristics, A-5
voltage output, A-5 to A-6
analog trigger
above-high-level analog triggering mode
(figure), 3-8
avoiding false triggering (note), 3-6
© National Instruments Corporation
I-1
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
below-low-level analog triggering mode
(figure), 3-7
ComponentWorks software, 1-3
configuration
block diagrams
PCI-6110E/6111E, 2-2
PCI-6110E, 3-6
questions about, C-2
PCI-6111E, 3-7
high-hysteresis analog triggering mode
(figure), 3-9
inside-region analog triggering mode
(figure), 3-8
low-hysteresis analog triggering mode
(figure), 3-9
connectors. See I/O connectors.
CONVERT* signal
input timing (figure), 4-24
multiplexer for controlling (figure), 3-11
output timing (figure), 4-24
signal routing, 3-11 to 12
timing connections, 4-23 to 4-25
counter/timer applications, C-4 to C-5
customer communication, xiv, D-1 to D-2
specifications, A-8
AOGND signal
analog output signal connections, 4-13
description (table), 4-3
D
signal summary (table), 4-6
DAC0OUT signal
analog output signal connections, 4-13
description (table), 4-3
signal summary (table), 4-6
DAC1OUT signal
analog output signal connections, 4-13
description (table), 4-3
signal summary (table), 4-6
DAQ timing connections, 4-17 to 4-26
AIGATE signal, 4-25
B
bipolar input, 3-3
block diagrams
PCI-6110E, 3-1
PCI-6111E, 3-2
board configuration, 2-2
bulletin board support, D-1
bus interface specifications, A-9
CONVERT* signal, 4-23 to 4-25
EXTSTROBE* signal, 4-18 to 4-19
SCANCLK signal, 4-18
SISOURCE signal, 4-25 to 4-26
STARTSCAN signal, 4-22 to 4-23
TRIG1 signal, 4-19 to 4-20
TRIG2 signal, 4-20 to 4-21
typical posttriggered acquisition
(figure), 4-17
C
cables. See also I/O connectors.
custom cabling, 1-5 to 1-6
field wiring considerations, 4-35 to 4-36
optional equipment, 1-5
calibration, 5-1 to 5-3
external calibration, 5-2 to 5-3
loading calibration constants, 5-1 to 5-2
self-calibration, 5-2
typical pretriggered acquisition
(figure), 4-18
clocks, board and RTSI, 3-12
commonly asked questions. See questions and
answers.
DAQ-STC system timing controller
overview, 1-1
questions about, C-1, C-3 to C-4
common-mode signal rejection, 4-12
PCI-6110E/6111E User Manual
I-2
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
data acquisition timing connections. See DAQ
timing connections.
DC input coupling, 3-4
E
EEPROM storage of calibration constants, 5-1
electronic support services, D-1 to D-2
e-mail support, D-2
DGND signal
description (table), 4-3
environment specifications, A-9
environmental noise, avoiding, 4-35 to 4-36
equipment, optional, 1-5
digital I/O connections, 4-13 to 4-14
signal summary (table), 4-6
timing connections, 4-16
differential measurements, 4-9 to 4-12
common-mode signal rejection, 4-12
connection considerations, 4-10
DIFF input mode, 3-2 to 3-3
floating signal sources, 4-9, 4-11 to 4-12
ground-referenced signal sources,
4-9, 4-11
EXTSTROBE* signal
description (table), 4-3
signal summary (table), 4-6
timing connections, 4-18 to 4-19
F
fax and telephone support numbers, D-2
Fax-on-Demand support, D-2
field wiring considerations, 4-35 to 4-36
floating signal sources
nonreferenced signal sources,
4-11 to 4-12
recommended configuration (table), 4-10
digital I/O
description, 4-9
operation, 3-10
differential connections, 4-11 to 4-12
recommended configuration (table), 4-10
FREQ_OUT signal
questions about, C-3 to C-5
signal connections, 4-13 to 4-14
specifications, A-6 to A-7
digital trigger specifications, A-8
DIO<0..7> signal
description (table), 4-5
general-purpose timing connections, 4-35
signal summary (table), 4-7
frequently asked questions. See questions and
answers.
FTP support, D-1
fuse, self-resetting, 4-15, C-2
description (table), 4-3
digital I/O connections, 4-13 to 4-14
signal summary (table), 4-6
dither
enabling, 3-4 to 3-5
signal acquisition effects (figure), 3-5
documentation
G
conventions used in manual, xii-xiii
National Instruments documentation,
xiii-xiv
general-purpose timing signal connections,
4-29 to 4-35
FREQ_OUT signal, 4-35
GPCTR0_GATE signal, 4-30 to 4-31
GPCTR0_OUT signal, 4-31
GPCTR0_UP_DOWN signal, 4-31
GPCTR1_GATE signal, 4-32 to 4-33
GPCTR1_OUT signal, 4-33
organization of manual, xi-xii
related documentation, xiv
dynamic characteristic specifications
analog input, A-4
analog output, A-6
© National Instruments Corporation
I-3
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
GPCTR1_SOURCE signal, 4-32
GPCTR1_UP_DOWN signal,
4-34 to 4-35
timing signal routing, 3-11 to 13
board and RTSI clocks, 3-12
CONVERT* signal routing
(figure), 3-11
questions about, C-4 to C-5
glitches, C-2
GPCTR0_GATE signal, 4-30 to 4-31
GPCTR0_OUT signal
programmable function inputs, 3-12
RTSI triggers, 3-13
description (table), 4-5
general-purpose timing connections, 4-31
signal summary (table), 4-7
I
input characteristic specifications, A-1 to A-2
input mode. See differential measurements.
input polarity and range, 3-3 to 3-4
actual range and measurement precision
(table), 3-3
GPCTR0_SOURCE signal, 4-29 to 4-30
GPCTR0_UP_DOWN signal, 4-31
GPCTR1_GATE signal, 4-32 to 4-33
GPCTR1_OUT signal
selection considerations, 3-4
installation
description (table), 4-4
general-purpose timing connections, 4-33
signal summary (table), 4-7
hardware, 2-1 to 2-2
questions about, C-2
software, 2-1
GPCTR1_SOURCE signal, 4-32
GPCTR1_UP_DOWN signal, 4-34 to 4-35
ground-referenced signal sources
description, 4-9
unpacking PCI-6110E/6111E, 1-6
I/O connectors, 4-1 to 4-7
cable connectors for
differential connections, 4-11
recommended configuration (table), 4-10
PCI-6110E/6111E, 1-6
exceeding maximum ratings
(warning), 4-1
I/O signal summary (table), 4-6 to 4-7
pin assignments (figure), 4-2, B-2
signal descriptions (table), 4-3 to 4-5
H
hardware installation
procedure, 2-1 to 2-2
unpacking PCI-6110E/6111E, 1-6
hardware overview
L
analog input, 3-2 to 3-5
dither, 3-4 to 3-5
input mode, 3-2 to 3-3
input polarity and range, 3-3 to 3-4
selection considerations, 3-4
analog output, 3-5
LabVIEW and LabWindows/CVI application
software, 1-2 to 1-3
M
manual. See documentation.
analog trigger, 3-6 to 3-9
block diagrams
PCI-6110E, 3-1
PCI-6111E, 3-2
digital I/O, 3-10
PCI-6110E/6111E User Manual
I-4
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
PFI2/CONVERT* signal
description (table), 4-4
signal summary (table), 4-6
PFI3/GPCTR1_SOURCE signal
description (table), 4-4
signal summary (table), 4-6
PFI4/GPCTR1_GATE signal
description (table), 4-4
signal summary (table), 4-7
PFI5/UPDATE* signal
N
NI-DAQ driver software, 1-3 to 1-4
noise, avoiding, 4-35 to 4-36
NRSE (nonreferenced single-ended input),
4-11 to 4-12
O
optional equipment, 1-5
output characteristic specifications, A-5
description (table), 4-4
signal summary (table), 4-7
PFI6/WFTRIG signal
P
PCI-6110E/6111E. See also hardware
overview.
description (table), 4-5
signal summary (table), 4-7
PFI7/STARTSCAN signal
description (table), 4-5
custom cabling, 1-5 to 1-6
optional equipment, 1-5
overview, 1-1 to 1-2
signal summary (table), 4-7
PFI8/GPCTR0_SOURCE signal
description (table), 4-5
signal summary (table), 4-7
PFI9/GPCTR0_GATE signal
description (table), 4-5
signal summary (table), 4-7
PFIs (programmable function inputs),
4-16 to 4-17
questions about, C-1 to C-5
analog input and output, C-2 to C-3
general information, C-1 to C-2
installation and configuration, C-2
timing and digital I/O, C-3 to C-5
requirements for getting started, 1-2
software programming choices, 1-2 to 1-4
ComponentWorks, 1-3
LabVIEW and LabWindows/CVI
application software, 1-2 to 1-3
National Instruments application
software, 1-2 to 1-3
NI-DAQ driver software, 1-3 to 1-4
register-level programming, 1-4
VirtualBench, 1-3
connecting to external signal source
(warning), C-5
overview, 4-16 to 4-17
questions about, C-4 to C-5
signal routing, 3-12
timing input connections, 4-16 to 4-17
PGIA (programmable gain instrumentation
amplifier)
unpacking, 1-6
PFI0/TRIG1 signal
analog input connections, 4-8
common-mode signal rejection, 4-12
differential connections
description (table), 4-4
signal summary (table), 4-6
PFI1/TRIG2 signal
floating signal sources (figure), 4-12
ground-referenced signal
description (table), 4-4
sources, 4-11
signal summary (table), 4-6
physical specifications, A-9
© National Instruments Corporation
I-5
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
pin assignments (figure), 4-2, B-2
polarity selection, analog input, 3-3 to 3-4
posttriggered data acquisition, 4-17
power connections
common-mode signal rejection, 4-12
connection considerations, 4-10
floating signal sources, 4-9,
4-11 to 4-12
ground-referenced signal sources,
4-9, 4-11
+5 V power pins, 4-15
self-resetting fuse, 4-15
nonreferenced signal sources,
4-11 to 4-12
recommended configuration
(table), 4-10
power requirement specifications, A-9
pretriggered data acquisition, 4-17 to 4-18
programmable function inputs (PFIs). See
PFIs (programmable function inputs).
programmable gain instrumentation amplifier.
See PGIA (programmable gain
instrumentation amplifier).
digital I/O, 4-13 to 4-14
field wiring considerations, 4-35 to 4-36
I/O connector, 4-1 to 4-7
exceeding maximum ratings
(warning), 4-1
Q
I/O signal summary (table),
4-6 to 4-7
questions and answers
pin assignments (figure), 4-2, B-2
signal descriptions (table), 4-3 to 4-5
power connections, 4-15
RTSI trigger lines, 3-13
timing connections, 4-15 to 4-35
DAQ timing connections,
4-17 to 4-26
analog input and output, C-2 to C-3
general information, C-1 to C-2
installation and configuration, C-2
timing and digital I/O, C-3 to C-5
R
register-level programming, 1-4
requirements for getting started, 1-2
RTSI clocks, 3-12
AIGATE signal, 4-25
CONVERT* signal,
4-23 to 4-25
EXTSTROBE* signal,
4-18 to 4-19
SCANCLK signal, 4-18
SISOURCE signal, 4-25 to 4-26
STARTSCAN signal,
RTSI trigger lines, 3-13
signal connection (figure), 3-13
specifications, A-8
S
4-22 to 4-23
TRIG1 signal, 4-19 to 4-20
TRIG2 signal, 4-20 to 4-21
typical posttriggered acquisition
(figure), 4-17
typical pretriggered acquisition
(figure), 4-18
SCANCLK signal
description (table), 4-3
signal summary (table), 4-6
timing connections, 4-18
signal connections
analog input, 4-8
analog output, 4-13
differential measurements, 4-9 to 4-12
PCI-6110E/6111E User Manual
I-6
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
general-purpose timing signal
connections, 4-29 to 4-35
FREQ_OUT signal, 4-35
GPCTR0_GATE signal,
4-30 to 4-31
input characteristics, A-1 to A-2
stability, A-4 to A-5
transfer characteristics, A-2 to A-3
analog output, A-5 to A-6
dynamic characteristics, A-6
output characteristics, A-5
stability, A-6
transfer characteristics, A-5
voltage output, A-5 to A-6
analog trigger, A-8
bus interface, A-9
digital I/O, A-6 to A-7
digital trigger, A-8
environment, A-9
physical, A-9
GPCTR0_OUT signal, 4-31
GPCTR0_SOURCE signal,
4-29 to 4-30
GPCTR0_UP_DOWN
signal, 4-31
GPCTR1_GATE signal,
4-32 to 4-33
GPCTR1_OUT signal, 4-33
GPCTR1_SOURCE signal, 4-32
GPCTR1_UP_DOWN signal,
4-34 to 4-35
power requirements, A-9
RTSI, A-8
programmable function input
connections, 4-16 to 4-17
waveform generation timing
connections, 4-26 to 4-29
UISOURCE signal, 4-28 to 4-29
UPDATE* signal, 4-27 to 4-28
WFTRIG signal, 4-26 to 4-27
types of signal sources, 4-9
floating, 4-9
timing I/O, A-7 to A-8
stability specifications
analog input, A-4 to A-5
analog output, A-6
STARTSCAN signal
input timing (figure), 4-22
output timing (figure), 4-23
timing connections, 4-22 to 4-23
ground-referenced, 4-9
SISOURCE signal, 4-25 to 4-26
software installation, 2-1
software programming choices, 1-2 to 1-4
ComponentWorks, 1-3
T
technical support, D-1 to D-2
telephone and fax support numbers, D-2
theory of operation. See hardware overview.
timing connections, 4-15 to 4-35
DAQ timing connections, 4-17 to 4-26
AIGATE signal, 4-25
LabVIEW and LabWindows/CVI
application software, 1-2 to 1-3
National Instruments application
software, 1-2 to 1-3
NI-DAQ driver software, 1-3 to 1-4
register-level programming, 1-4
VirtualBench, 1-3
CONVERT* signal, 4-23 to 4-25
EXTSTROBE* signal, 4-18 to 4-19
SCANCLK signal, 4-18
SISOURCE signal, 4-25 to 4-26
STARTSCAN signal, 4-22 to 4-23
TRIG1 signal, 4-19 to 4-20
specifications
analog input, A-1 to A-5
amplifier characteristics, A-3 to A-4
dynamic characteristics, A-4
TRIG2 signal, 4-20 to 4-21
© National Instruments Corporation
I-7
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
typical posttriggered acquisition
(figure), 4-17
output timing (figure), 4-21
timing connections, 4-20 to 4-21
typical pretriggered acquisition
(figure), 4-18
general-purpose timing signal
connections, 4-29 to 4-35
FREQ_OUT signal, 4-35
trigger, analog
above-high-level analog triggering mode
(figure), 3-8
avoiding false triggering (note), 3-6
below-low-level analog triggering mode
(figure), 3-7
GPCTR0_GATE signal, 4-30 to 4-31
GPCTR0_OUT signal, 4-31
GPCTR0_SOURCE signal,
4-29 to 4-30
block diagrams
PCI-6110E, 3-6
PCI-6111E, 3-7
GPCTR0_UP_DOWN signal, 4-31
GPCTR1_GATE signal, 4-32 to 4-33
GPCTR1_OUT signal, 4-33
GPCTR1_SOURCE signal, 4-32
GPCTR1_UP_DOWN signal,
4-34 to 4-35
high-hysteresis analog triggering mode
(figure), 3-9
inside-region analog triggering mode
(figure), 3-8
low-hysteresis analog triggering mode
(figure), 3-9
programmable function input
connections, 4-16 to 4-17
questions about, C-3 to C-5
timing I/O connections (figure), 4-16
waveform generation timing connections,
4-26 to 4-29
specifications, A-8
triggers
questions about, C-3
specifications
analog trigger, A-8
digital trigger, A-8
UISOURCE signal, 4-28 to 4-29
UPDATE* signal, 4-27 to 4-28
WFTRIG signal, 4-26 to 4-27
U
timing I/O specifications, A-7 to A-8
timing signal routing, 3-11 to 3-13
board and RTSI clocks, 3-12
CONVERT* signal routing (figure), 3-11
programmable function inputs, 3-12
RTSI triggers, 3-13
UISOURCE signal, 4-28 to 4-29
unpacking PCI-6110E/6111E, 1-6
UPDATE* signal
input signal timing (figure), 4-28
output signal timing (figure), 4-28
timing connections, 4-27 to 4-28
transfer characteristic specifications
analog input, A-2 to A-3
V
analog output, A-5
VCC signal (table), 4-6
TRIG1 signal
VirtualBench software, 1-3
voltage output specifications, A-5 to A-6
input timing (figure), 4-20
output timing (figure), 4-20
timing connections, 4-19 to 4-20
TRIG2 signal
input timing (figure), 4-21
PCI-6110E/6111E User Manual
I-8
© National Instruments Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
W
waveform generation, questions about, C-3
waveform generation timing connections,
4-26 to 4-29
UISOURCE signal, 4-28 to 4-29
UPDATE* signal, 4-27 to 4-28
WFTRIG signal, 4-26 to 4-27
WFTRIG signal
input signal timing (figure), 4-27
output signal timing (figure), 4-27
timing connections, 4-26 to 4-27
wiring considerations, 4-35 to 4-36
© National Instruments Corporation
I-9
PCI-6110E/6111E User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|