DigiComp16booklet 1/23/03 10:26 AM Page 2
SERVICE FOR YOUR NADY AUDIO PRODUCT
(U.S.) Should your NADY AUDIO product require service, please contact the
Nady Service Department via telephone at (510) 652-2411, or e-mail at
(International) For service, please contact the NADY AUDIO distributor in your
country through the dealer from whom you purchased this product.
O W N E R ’ S M A N U A L
DO NOT ATTEMPT TO SERVICE THIS UNIT
YOURSELF AS IT CAN BE DANGEROUS AND
WILL ALSO VOID THE WARRANTY.
DigiComp 16
NADY SYSTEMS, INC. • 6701 SHELLMOUND STREET, EMERYVILLE, CA 94608
18-bit Digital Compressor
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:26 AM Page 6
Block Diagram
Contents
Warning ..................................................................4
Preset Function Descriptions
Stereo AGC ..........................................................12
Dynamic Compression Process............................13
Stereo 2 Bands Compressor ................................13
Stereo 2 Bands Compressor Preset ....................14
Mono 2 Bands + 5 Bands Eq Compressor ..........15
Mono 2 Bands + Bands Eq
Installation
Inspection................................................................5
Desktop Use ..........................................................5
Rackmount..............................................................5
Compressor Presets ............................................16
Compression Effects Summary Table ..................16
Front Panel Controls
Input Level Control ................................................6
Output Level Control ..............................................6
Process Bypass Switch ..........................................6
Peak LED................................................................6
Power LED..............................................................6
Program Select Control ..........................................6
Variations Select Control ........................................6
Block Diagram ....................................................18
Specifications......................................................19
Service ....................................................Back Cover
Rear Panel Connections
Power Jacks............................................................7
Bypass Jacks..........................................................7
Input (Left/Mono &Right) Jacks ..............................7
Output (Left & Right) Jacks ....................................7
Installation and Connection
Audio Connections and Power Up..........................8
Analog ....................................................................8
a. Input Jack Wiring ..........................................8
b. Level Setting ................................................8
c. Compression Process Bypass......................9
Installation ..............................................................9
a. Standard Use................................................9
b. Application Examples ..................................9
18
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:26 AM Page 8
Warning
An equilateral triangle enclosing a lightening flash/arrowhead symbol is
AGC
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure which may be of sufficient
magnitude to constitute a risk of electric shock.
EXP SPEED CMP SPEED
EXP THR
(dB)
-61
-34
-42
-34
-44
-44
-37
-37
-37
-37
-44
-44
-42
-34
-61
CMP THR
(dB)
-26
-29
-26
-29
-29
-29
-29
-22
-27
-27
-27
-27
-27
-27
-27
THR HOLD EXP RATIO
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
(dB/s)
3.5
3.5
3.5
4
3.2
3.3
3.2
4.1
4.1
4.5
4.5
5.6
6
(dB/s)
23
19.5
19.5
24
(dB)
-44
-32
-38
-31
-31
-42
-33
-31
-31
-30
-29
-42
-31
-30
-32
(In:Out)
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
An equilateral triangle enclosing an exclamation point is intended to alert
the user to the presence of important operating and service instructions in
the literature enclosed with this unit.
AGC 1
AGC 2
AGC 3
AGC 4
AGC 5
AGC 6
AGC 7
AGC 8
AGC 9
AGC 10
AGC 11
AGC 12
AGC 13
AGC 14
AGC 15
IMPORTANT SAFETY INSTRUCTIONS
24
22.5
24.3
23
When using this electronic device, basic precautions should always be taken, including the following:
1. Read all instructions before using the product.
23
2. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet
basement, near a swimming pool, etc.).
24.3
22.5
24
19.5
19.5
23
3. This product should be used only with a cart or stand that will keep it level and stable and prevent
wobbling.
6
6
4. This product, in combination with headphones or speakers, may be capable of producing sound
levels that could cause permanent hearing loss. Do not operate for a long period of time at a high
volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the
ears, you should consult an audiologist.
EQ CLASSIC PRESET
5. The product should be positioned so that proper ventilation is maintained.
PEQ 1
PEQ 2
PEQ 3
PEQ 4
PEQ 5
6. The product should be located away from heat sources such as radiators, heat vents, or other
devices (including amplifiers) that produce heat.
Classic 1
Classic 2
Classic 3
Classic 4
Classic 5
Classic 6
Classic 7
Classic 8
G=1dB; F=75Hz
Q=1
G=1dB; F=75Hz
Q=1
G=1dB; F=75Hz
Q=5
G=2dB; F=50Hz
Q=5
G=1dB; F=75Hz
Q=1
G=1dB; F=75Hz
Q=1
G=1dB; F=75Hz;
Q=5
G=2dB; F=50Hz;
Q=5
G=0dB
G=0,5dB;
F=1KHz; Q=1
G=-1dB; F=1KHz
Q=1
G=-1dB; F=1KHz
Q=1
G=-6dB;F=1KHz;
Q=1
G=-1dB;F=1KHz
Q=1
G=0.5dB; F=1KHz
Q=1
G=-1dB; F=1KHz
Q=1
G=-6dB; F=1KHz;
Q=1
G=-0dB
G=1dB; F=12KHz
Q=1
7. The product should be connected to a power supply only of the type described in the operating
instructions or as marked on the product. Replace the fuse only with one of the specified type, size,
and correct rating.
G=-1dB;
F=600Hz; Q=5
G=-1dB
F=600Hz;Q=5
G=-10dB;
F=100Hz; Q=5
G=-1dB;
F=600Hz; Q=5
G=0dB
G=1dB;
G=-1dB;
F=3.7KHz;Q=5 F=12KHz;Q=1
G=-2dB;
F=3.7KHz;Q=5
G=-4.5dB;
F=3.7KHz;Q=1
G=1dB;
G=1dB; F=7KHz
Q=5
G=2dB;F=10KHz
Q=5
8. The power supply cord should: (1) be undamaged, (2) never share an outlet or extension cord
with other devices so that the outlet’s or extension cord’s power rating is exceeded, and (3) never be
left plugged into the outlet when not being used for a long period of time.
G=-1dB;
9. Care should be taken so that objects do not fall into, and liquids are not spilled through, the
enclosure’s openings.
F=3.7KHz; Q=5 F=12KHz; Q=1
G=0dB
G=1dB; F=12KHZ
Q=1
G=1dB; F=7KHz;
Q=5
10. The product should be serviced by qualified service personnel if:
G=-1dB
F=600Hz; Q=5
G=-10dB;
G=-2dB;
F=3.7KHz; Q=5
G=-4.5dB; G=2dB; F=10KHz;
F=3.7KHz; Q=1 Q=5
A. The power supply cord or the plug has been damaged.
B. Objects have fallen into, or liquid has been spilled onto the product.
C. The product has been exposed to rain.
F=100Hz; Q=5
D. The product does not appear to operate normally or exhibits a marked change
in performance.
E. The product has been dropped, or the enclosure damaged.
11. Do not attempt to service the product beyond what is described in the user maintenance
instructions. All other servicing should be referred to qualified service personnel.
4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:26 AM Page 10
Installation
This type of dynamic process is very useful for the dynamic control of instruments or
“single” sounds.
To ensure years of enjoyment from your NADY AUDIO DigiComp 16 sound processor,
please read and understand this manual thoroughly before using the unit.
Mono 2 Band + 5 Bands EQ Compressor Presets
There are 8 presets available using the above algorithms:
INSPECTION
Your DigiComp 16 was carefully packed at the factory in packaging designed to protect
the units in shipment. Before installing and using your unit, carefully examine the
packaging and all contents for any signs of physical damage that may have occurred in
transit.
1) Classic 1
3) Classic 3
5) Classic 5
7) Classic 7
2) Classic 2
4) Classic 4
6) Classic 6
8) Classic 8
(Note: Nady Systems is not responsible for shipping damage. If the unit is damaged in
shipping, do not return to us, but notify your dealer and the shipping company
immediately to make a claim. Such claims must be made by the consignee in a timely
manner.)
These are all designed for use with single instruments. These presets are well tailored
for use on classic guitars or acoustic instruments, where different equalizations of the
sound (ranging from bright equalizations to warmer ones) can give the instruments more
or less character and deepness.
CONTENTS:
• DigiComp 16 (verify that the same serial number is the same as shown on
shipping carton)
Compression Effects Summary Table
• AC Power supply adapter
• Instruction manual
• Warranty Card
LIMITER
Band Split (Hz)
Limiter Low
Volume Low
Volume High
Band (dB)
Band (dB)
Band (dB)
AGC PURE
ACOUSTIC
MASTER
CLEAN
DANCE
KICK DRUM
MIX DOWN
JUMP UP
800
2500
630
3150
160
250
5000
1250
0
-2
-2
0
2
4
0
6.5
8
0
6.5
-4.5
5
2
2.5
2
DESKTOP USE
The DigiComp 16 may be placed anywhere safely as needed where it will not fall or be
possibly damaged. Attach the rubber feet provided to the bottom of the unit if the unit is
placed on a surface you wish to protect.
-3
-1.5
-1.5
-3
(Note: The DigiComp 16 itself doesn’t generate any magnetic or hum fields, but it may
pick up hum or noise from fields generated by power amplifiers. If it does, re-position the
unit to eliminate the noise. Since the DigiComp 16 adapter may generate hum fields,
locate it away from other audio equipment or wiring as much as possible.)
2
2
-1
4
COMPRESSOR
Threshold (Hz)
Release (dB/s)
Attack (dB)
AGC PURE
ACOUSTIC
MASTER
CLEAN
DANCE
KICK DRUM
MIX DOWN
JUMP UP
CLASSIC
1,2,3,4,5,6,7
0
-2
-2
2.5
-1.5
-0.5
-2
-1.5
-6
-
-
RACK MOUNTING
33
34
30
50
86
32
57
6.5
111
29
111
72
137
25
72
The DigiComp 16 has single rack height, and up to three DigiComp 16’s may be
mounted side-by-side in a standard universal 19” equipment rack available from rack
manufacturers or your music dealer.
85.6
16
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:26 AM Page 12
Front Panel Controls
(3)
(7)
(6)
brilliance. It is well suited for processing dynamic and brilliant recordings, increasing their
"punch".
6) Kick Drum: In this preset, mid-low range is emphasized, while high and mid
frequencies are slightly attenuated. This special preset is extremely well suited for drum
recordings. It is ideal for underlining drums’ low range in multitrack recordings or mixed
microphone environments.
7) Mixdown: Mixdown is less brilliant than Clean Preset and mid-low end is more
pronounced. This is ideal for underlining bass and drums without losing definition in the
rest of the range. This preset is also suited for harmonically complex instruments, e.g.
double bass, which have a non-negligible high frequency range.
9) Jumping Up: The Jumping Up Preset is quite similar to Clean Preset in its general
timbre, but this preset is particularly effective with male voices and is capable of
maintaining the level in soft passages of a music program. For female voices, the Clean
Program is generally preferred.
(1)
(2)
(4)
(5)
Before using the DigiComp 16, it is best to familiarize yourself with the functions of all the
controls and connections. After you have set up your unit, you should refer back to these
descriptions to fully optimize operation in your paticular application.
Mono 2 Bands+ 5 Bands EQ Compressor
(1) Input Level Control
The DigiComp 16’s Mono 2 Bands +5 Bands EQ dynamic process algorithm is based on
a "multi-band" process concept, splitting the full band signal entering the dynamic
process algorithm into 2 "sub-bands" — the low frequencies band and the mid/high
frequencies band. This enables differentiation of the dynamic processes operating on the
low frequencies (with higher energy content) and on the mid/high frequencies (with lower
energy content). This technique avoids the common "pumping" effect which often occurs
when applying a dynamic process to a sound signal.
Once the input signal is split into 2 "sub-bands", the DigiComp 16 operates a first limiting
process on the low frequencies band, and then, once the full band, is restored, it applies
a powerful stereo dynamic process on the two "recombined" channels.
The input signal to the dynamic compression "block" is the sum of the input signals
filtered with a 5 bands parametric EQ.
The input level control sets the main input gain, before the signal reaches the input bus.
It controls both Left (MONO) and Right input levels simultaneously.
(2) Output Level Control
The output level control sets the level going to the amplifer or mixer from this apparatus.
(3) Process Bypass Switch
This switch allows you to bypass the digital process to have the input signal available on
the outputs.
(4) Peak LED
This displays the signal level being processed by the DigiComp 16. If the signal level is
at overload, this LED will light red continuously and you might begin to hear the signal
distort. Back off the INPUT CONTROL (1) until the LED lights only occasionally.
(5) Power LED
This is lit whenever the DigiComp 16 power adapter is plugged in.
(6) Program Select Control
The Program select knob is used to choose the program you wish to activate.
(7) Variations Select Control
Each program on this apparatus has the AGC parameter which can be adjusted by
means of this knob.
This feature allows you to modify the "color" of the input signal before applying the
dynamic process.
6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:33 AM Page 14
Rear Panel Connections
This technique helps avoid the common "pumping" effect which often arises when
applying a dynamic process to a sound signal.
(10)
(11)
(12)
(9)
(13)
Once the input signal is split into 2 "sub-bands", the DigiComp 16 operates a first limiting
process on the low frequencies band, and then, once the full band, is restored, it
applies a powerful stereo dynamic process on the two "recombined" channels.
(8)
(8) Power Jack
This is a plug for connecting the Nady 9VAC power supply adapter (supplied).
The DigiComp 16 comes with a power adapter suitable for the voltage of the country it is
shipped to (either 110 or 220V, 50 or 60Hz).
(Note: The correct power supply must be used AT ALL TIMES — any other power supply
might create a fire risk and/or permanently damage your unit. This damage would NOT
be covered under your warranty.)
This type of dynamic process is very useful for the dynamic control of complex audio —
a CD, an orchestra, etc.
Stereo 2 Bands Compressor Presets
(9) Bypass Jack
1) AGC pure: This preset is a simple automatic level control. Its speed varies with the
different "variation" control positions. From a timbre point of view, it's a rather neutral
process, and it doesn't alter the general balance of the original signal. It simply keeps
the level in proximity of a fixed level, correcting the source variations. Note that variation
1 disables the AGC — it does so even in the compressor presets. This variation can be
considered a sort of bypass.
2) Acoustic: The general impression this preset gives is of definition and power. The
timbre is lively and brilliant, ideal for small ensemble music and keeping live soft
passages. Frequency response is slightly rolled off in the low end.
This is a 1/4” phone jack for connecting to an effects bypass footswitch. You can bypass
the effects in two ways, thus allowing the direct signal to pass through the DigiComp 16
unchanged:
• By pressing the PROCESS BYPASS SWITCH (3), or by connecting a footswitch to this
jack and pressing the footswitch. Each time this footswitch is pressed, the Bypass mode
will turn on and off alternately.
(10) & (11) Output (Left & Right) Jacks
3) Master: Master is very neutral and is usable as a high performance AGC. It can be
put before power amps and recorders in order to optimize their dynamic range. Timbre is
very similar to original signals, and so the unique appreciable differences are in the
dynamic range corrections. Variations 2 through 16 activate even the AGC to enable
variable compressor action.
4) Clean: This is a high definition preset, providing great brilliance and dynamic
impression. Nevertheless it is never fatiguing and "pushes" the sound without
unbalancing it. Highs and the punch range are emphasized and lows are not overly
attenuated. It is great for underlining details in female vocals.
These 1/4” unbalanced phone jacks connect to devices such as the effects returns,
channel inputs or inserts on a mixing console, or power amplifier inputs. For mono
applications, use the LEFT (10) output.
(12) & (13) Input (Left/Mono & Right) Jacks
These 1/4” unbalanced phone jacks connect to sources such as the effects sends of
mixing consoles. They may be used with nominal input levels from -8/9dBV. The
Left/Mono input jack is normal to the Right jack. This means that when nothing is
plugged into the RIght input jack, the signal present at the Left/Mono input is routed to
the Right as well.
5) Dance: With this program, medium range and mid-low range are emphasized, while
high frequencies are slightly attenuated. This helps control dance music’s intrinsic
14
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 10:33 AM Page 16
Installation and Connection
Audio Connections and Power Up
The connections between the DigiComp 16 and other audio devices have to be made
using high-quality cables to insure optimum performance of this unit. It is best to use low
capacitance shielded cables with a flexible internal conductor. Connect the cables to the
unit properly by observing the following precautions:
• Do not bundle audio cables with AC power cords.
• Do not place audio cables and DigiComp 16 near sources of electromagnetic
interference such as transformers, monitors, computers, etc.
Dynamic Compression Process
As the name implies, compression reduces the dynamic range of a signal. It is used
extensively in audio recording, production work, noise reduction, and live performance
applications, and needs to be used with care. A compressor is basically a variable gain
device wherein the amount of gain used depends on the level of the input. In this case,
the gain will be reduced when the signal level is high, making louder passages softer
• Always unplug cables by firmly grasping the body of the plug and pulling directly
outward.
• Do not place cables where they can be stepped on.
• Avoid twisting a cable or having it make sharp, right angle turns. Before powering up
the DigiComp 16, check that all connections have been made correctly.
• Turn down volume controls of the amplifier or mixer. Insert the Power plug into the
POWER input on the rear panel of the DigiComp 16 and plug the power adapter into
an AC outlet. Turn on the power of the amplifier/mixer and adjust the volume.
and reducing the dynamic range.
Analog
a. Input Jack Wiring
The DigiComp 16’s LEFT INPUT (12) jack is also the mono input for the unit. If you only
connect a single mono cable to the LEFT INPUT (12) jack, it will also be routed
automatically to the RIGHT INPUT (13). However, if you are using stereo input signals
and also connecting a cable to the RIGHT INPUT (13) jack, the automatic routing will be
avoided and the left input cable will feed only the LEFT INPUT (12), and the right input
cable will feed only the RIGHT INPUT (13).
b. Level Setting
Proper setting of the input and
output levels is crucial in order
to achieve the maximum
signal-to-noise ratio. It is
usually best to set both input
and output level controls at 3/4
or 75% of maximum. This will
A compressor’s input/output relationship can be illustrated by a simple graph:
The horizontal axis corresponds to the input signal level, and the vertical axis is the
output level (both measured in decibels). A line at 45 degrees corresponds to a gain of
one — any input level is mapped to exactly the same output level. The compressor
changes the slope of that line (makes it more horizontal) above some value called the
threshold (which is most often adjustable). The height of the line defines the dynamic
range of the output, and the slope of the line is the same as the compressor's gain.
decrease the possibility of
overload distortion and keep
Stereo 2 Bands Compressor
the amount of background noise to a minimum. If the Signal LED (4) on the DigiComp 16
lights up, signaling a process saturation, turn down the INPUT LEVEL (1) or decrease
the volume of the source (instrument, mixer send, etc.). If the unit level is causing the
mixer or amp to distort, turn the OUTPUT LEVEL (2) down.
The DigiComp 16’s Stereo 2-bands dynamic process algorithm is based on a
"multiband" process concept, splitting the full band of the input signals into 2
"sub-bands" — the low frequencies band and the mid/high frequencies band — in order
to differentiate the dynamic processes operating on the low frequencies (with higher
energy content) and the mid/high frequencies (with lower energy content).
8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 12:50 PM Page 18
Preset Functions
c. Compression Process Bypass
Stereo AGC
At any time you can bypass the process, thereby allowing the direct signal to pass
through the DigiComp 16 unchanged. This can be done in two ways:
• By pressing the BYPASS switch (3)
• By connecting a footswitch to the BYPASS jack (9) and pressing the footswitch. On the
back panel you will find a footswitch jack labelled BYPASS. This is a mono jack with
connections for a standard footswitch. The footswitch must be plugged in before the
DigiComp 16 has its power turned on — the DigiComp 16 will automatically recognize
the right “polarity” of the pedal.
The DigiComp 16’s dynamic process algorithm also includes a stereo Automatic Gain
Control (AGC) "block" that, if used, is able to maintain almost stable the mean amplitude
of the input signal, increasing it when the "average"of the input signal amplitudes seems
to be low and decreasing it when the "average" of the input signal amplitude seems to be
too high. This process is useful when the sound reaching the input of the DigiComp 16 is
coming from different sources having different output levels and it is necessary to
"NORMALIZE" the input level of the DigiComp 16 to obtain better performance from the
Installation
a. Standard Use
The DigiComp 16 may be placed anywhere — on a table, on top of an amp, next to a
mixing console. If it will be on furniture, use the rubber feet provided for the bottom of the
unit. Make sure to place the unit’s power supply away from other audio equipment that
may induce fields, and away from the signal wiring. It is possible that the DigiComp 16
may pick up noise fields generated by other equipment such as a large power amplifier.
In this case, move the unit until the noise goes away.
b. Application Examples
Line Instrument — When connecting audio cables and/or turning power on and off, make
sure that all devices in your system have their volume controls turned down. The
DigiComp 16 has two 1/4” unbalanced inputs and two 1/4” unbalanced outputs. This
input/output configuration may provide three different audio connection options:
dynamic process operating as "second block" of the algorithm.
1) Expander Speed: This parameter represents the speed at which the signal is
expanded beyond the Expander Threshold. This occurs only if the Max value is different
from 0dB.
2) Compressor Speed: This parameter represents the speed at which the signal is
compressed once it goes beyond the Compressor Threshold. This occurs only if the Min
value is different from 0dB.
3) Expander Threshold: This is the threshold beyond which the signal is expanded.
4) Compressor Threshold: This is the threshold beyond which the signal is
compressed.
• Mono
Connect an audio cable to the LEFT INPUT (12) of the DigiComp 16 from a mono
source, and another audio cable from the LEFT OUTPUT (10) of the DigiComp 16 to an
amplification system or mixer input.
5) Hold Threshold: When this threshold is crossed by the signal level, coming from the
compression region, the compression coefficient is maintained steady. When the
crossing is from the expansion region, the expansion coefficient is kept the same.
6) Max: This is the maximum expansion ratio between input and output in the expansion
region.
From Instrument or
Effect Send
7) Min: This is the maximum compression ratio between input and output in the
compression region. The AGC = Const. areas are regions in which the multiplying
coefficient value assumes the last calculated before crossing the different thresholds, so
in the expansion area the COEF AGC value is increasing, while in the compression area
the COEF AGC value is decreasing.
To Mixing or Amplifier
Console
12
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DigiComp16booklet 1/23/03 12:01 PM Page 20
• Mono In, Stereo Out
While still using the LEFT (12) mono input, connect two audio cables from the LEFT (10)
and RIGHT (11) OUPUTS of the DigiComp 16 to a stereo amplification system or two
mixer inputs.
Insert jacks on the back of a mixer provide a way of "inserting" external processing
equipment into the signal path. The insert occurs after the input amplifier, and before the
channel fader; essentially it is the same as connecting the source (instrument or mic)
into the DigiComp 16 before the mixer's channel input. Usually, insert connections
require a special, stereo-splitting Y-cord. This Y-cord has a stereo 1/4” TRS jack that
plugs into the mixer's channel insert socket, and two mono 1/4” TRS jacks (input and
output) that will plug into the DigiComp 16. This kind of adapter cord will virtually insert
the compression processing into one mixer's channel. Carefully adjust the DigiComp 16
input and output levels in order to satisfy the dynamic requirements of both the
processed channels. If you don't hear anything, try to swap the Input and Output ends of
the TRS cable plugged into the DigiComp 16. Do not use the effects send/return
connections found on most mixers for effect modules, as this could result in heavy
frequency response alterations.
• Stereo
Connect two audio cables to the LEFT (12) and RIGHT INPUTS (13) of the DigiComp 16
from a stereo source, and two other audio cables from the LEFT (10) and RIGHT (11)
OUPUTS of the DigiComp 16 to a stereo amplification system or two mixer inputs.
Mono In
If you only want to use the DigiComp 16 for a mono input signal and to connect both of
its outputs back to the mixer, you will need three audio cables. Connect a channel insert
from the console to the LEFT mono input of the DigiComp 16 via TRS, and another
audio cable from the LEFT or RIGHT output of the DigiComp 16 to an adjacent mixer
input.
Interfacing to a Mixing Console — The DigiComp 16 can accept mono or stereo sends
at all system levels. The input circuitry of the DigiComp 16 can easily accept
professional +8/9 dBu levels while having enough input and output gain to interface with
the low signal levels of home recording systems. The DigiComp 16 may be connected to
a mixing console connecting the unit directly to the channel insert socket of a single
channel that is to be processed. Another way of interfacing the DigiComp 16 to a mixer
or recording console would be in-line between the output of the mixing console and the
input of a tape deck or power amplifier. This last setup would be used only if you wanted
to process the entire mix.
Stereo In - Stereo Out
This connection is similar to the one described above. However, by utilizing two TRS
cables and the console channel inserts, you can process two signals or a stereo signal
(e.g., from a keyboard). This operational mode is the one used with the algorithms (1 to
8), designed to process audio stereo sources such as CD’s. Improper level setting when
using a dynamic processor is the most common cause of noise and distortion problems,
so always be careful to ensure optimum audio.
Using Inserts — In the figure below, the situation is described in which the DigiComp 16
applies the desired dynamic process to single instrument signals; in this case, you must
use a mixer that features individual channel inserts.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|