VHF W ire le ss Micro p h o n e Sy ste m
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION
Thank you for purchasing a Nady Encore I Wireless Microphone System and
congratulations on your choice. The Encore I is loaded with top professional operat-
ing features and is the best performance and price value available in VHF wireless
systems.
CONTENTS ........................................................................................... 2
INTRODUCTION .................................................................................... 3
USING THIS MANUAL............................................................................ 3
SYSTEM FEATURES ................................................................................ 4
ENCORE I RECEIVER .............................................................................. 5
WHT-15 HANDHELD MICROPHONE TRANSMITTER ................................. 8
USING THIS MANUAL
This booklet gives instructions for the operation of the Encore I VHF wireless, including
handheld, instrument, lavalier, headmic and plug-in transmitter systems. Please read
the instructions for your system completely before operating unit.
This manual will first list the features of the Encore I and then will take you step by
step to show you how to operate your new system. After reading the receiver
instructions, turn to the section of the booklet that covers the type of transmitter used
with your new system. Each section will give you detailed operating instructions. Also
included in this manual are system specifications and servicing information.
WLT-15 LAVALIER/ LAPEL OR HEADWORN MICROPHONE
BODYPACK TRANSMITTER ................................................................... 10
WGT-15 INSTRUMENT BODYPACK TRANSMITTER................................. 12
THE LINK 2™ PLUG-IN TRANSMITTER. .................................................. 14
SPECIFICATIONS ................................................................................. 17
SERVICE .............................................................................................. 18
3
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM FEATURES
ENCORE I RECEIVER
1. Rackmounting the Receiver
There are 2 options available for rackmounting the Encore I receiver: singly or side-
by-side with another Encore Series receiver.
• Available on selected frequencies in the VHF high band
(171-216 MHz) for interference-free, long-range performance
• Proprietary companding circuitry for an industry-best 120dB Dynamic Range,
and the clearest, most natural sound available
• Operating Range: Up to 250 feet typical (depending on site conditions) – up to
500+ feet line-of-sight
a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of
the receiver (as shown) and slide in the optional ERM-12 RACK EARS (9).
b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from
both Encore receivers, join the two receivers with the EJC-2 JOINING CLIP (10)
and attach the ERM-22 RACK EARS (12) as shown. (Note: Do not mount the
receiver in a rack directly above an amplifier or other source of high heat – this
could degrade the performance of the Encore I. Always ensure adequate
airflow and heat dissipation in any rack configuration.)
• Noise-free transmitter ON-OFF operation
• Rugged, foam-padded traveling case provides easy, safe transport and storage
ENCORE I RECEIVER
• Half-rack receiver design with retractable front panel antenna
• RF and AF 5-LED displays for monitoring incoming signal strength
and audio level
• Balanced XLR and unbalanced adjustable 1/4" jack outputs
• Mute (squelch) adjust control
• Externally powered by AC/DC power adapter
• Unique snap-out panel locking tabs for single receiver or dual receiver
(side-by-side) optional rack mounting
2. Powering the Receiver
Plug the 12V AC/ DC ADAPTER (15) provided into the DC INPUT JACK (11) on the
back of the receiver. Then plug the power supply into an AC outlet. (Note: Any 12V
DC source with 400mA capability can also be used.) Press the POWER SWITCH (8)
once to turn on the receiver. The POWER ON LED (7) will now light and the receiver
is operational.
3. Antenna
WHT-15 HANDHELD MIC TRANSMITTER
The Encore I receiver is supplied with a TELESCOPIC ANTENNA (16). This should be
extended fully to obtain maximum range. Optimal antenna position is vertical. For
maximum range, it is always best to maintain a line of sight (no obstructions)
between the receiver antenna and the transmitter at all times whenever possible.
• Features the Nady DM-10D unidirectional neodymium dynamic cartridge for
optimum true sound, maximum feedback rejection and minimal handling noise
• OFF/STANDBY/ON switch allows convenient audio muting with the
transmitter "ON"
• Low battery LED indicator flashes once for unit "ON"; lights steady for low
battery alert
• Rubber, "easy-mount" mic clip included
4. Mute (Squelch) Adjustment
In normal operation, the MUTE CONTROL (2) should be set fully counterclockwise to
the factory preset minimum RF level. However, in areas of high RF activity, the mute
(or squelch, as it is sometimes called) may need to be adjusted to compensate for the
adverse conditions in a particular location. If, with the transmitter off, one or more
LEDs of the 5 LED RF LEVEL DISPLAY (4) flicker or stay on, the squelch control should
be turned clockwise until the LEDs extinguish. When the squelch is properly adjusted,
the RF LEVEL LED displays will only light when the system transmitter is turned on.
Turning the squelch control too far clockwise will reduce the range, but yield a quieter
mute (squelch) function. When the 5 LED RF LEVEL display extinguishes, the transmit-
ter is out of range for that given location, and the user should move closer to the
receiver to re-establish the radio link.
WGT-15 & WLT-15 BODYPACK TRANSMITTERS
• Choice of instrument (WGT-15) or headworn/lavalier microphone (WLT-15)
bodypack transmitter
• OFF/STANDBY/ON switch allows convenient audio muting with the
transmitter "ON"
• Low battery LED indicator flashes once for unit "ON"; lights steady for low
battery alert
• Locking 3.5mm mini-jack provides secure connection for removable micro
phone or instrument cable
• Easily accessible input level adjust control for optimum sound
LINK 2™ PLUG-IN TRANSMITTER
• Plug-in transmitter converts your favorite XLR handheld or lavalier micro
phone to wireless instantly
• Rugged construction and positive locking connector for reliable performance
• Selectable phantom power and LO/HI audio input level
• Optional leatherette pouch with clip available for use as bodypack
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
16
5. Connecting the Audio Output
The Encore I receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR
(14) and an adjustable line level UNBALANCED AUDIO OUTPUT 1/ 4" JACK (13).
The level from the UNBALANCED OUTPUT is controlled by the rear panel VOLUME
CONTROL (6). (Note: As when making any connection, make sure the amplifier or
mixing board volume is at the minimum level before plugging in the receiver to avoid
possible sound system damage. Also make sure that the phantom power on the input
of the mixer is turned OFF before making connection to the receiver.)
7
a. Instrument Connection (using the WGT-15 instrument transmitter)
Insert an audio cord with a 1/4" mono phone plug in the UNBALANCED
OUTPUT JACK (13) on the rear panel of the receiver. Plug the other end of the
cord into an amplifier, effects, or mixing board. Adjust the VOLUME CON-
TROL (6) on the Encore I receiver clockwise to about 3/4 rotation, until the
volume level is comfortable for your application. This setting is roughly
equivalent to a direct instrument cord connection. Turning the volume up to
maximum will provide 4dB gain over a cord.
5
8
4
b. Microphone Connection (using the WLT-15 transmitter with either a headset
or lavalier microphone or the WHT-15 handheld microphone transmitter)
For microphone use, either the BALANCED MIC AUDIO OUTPUT XLR (14) or
the 1/4" line level UNBALANCED OUTPUT (13) can be used. The XLR output
is set at a non-adjustable microphone level, similar to hardwired mic levels.
Plug an XLR connector into the XLR output jack on the rear of the unit and plug
the other end into your amplifier or mixing board. (Note: Make sure the
phantom power on your mixing board is turned off and the volume is turned
down when making connections.)
12-15V
VOLUME
MUTE
UNBALANCED OUT DC INPUT
BALANCED OUT
15
11
6
2
13
14
For your convenience, the XLR output level is preset at the factory and is not
adjustable with the receiver volume control. To use the 1/4" UNBALANCED
OUTPUT JACK (13), follow the instructions for the Instrument Connection
(above), except start with the receiver volume at 1/2 MAX and adjust the
volume control until the volume level is optimal. If the volume control is set too
high, you may overload your mixer or amp.
1
9
9
1
12
10
12
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WHT-15 HANDHELD MICROPHONE TRANSMITTER
1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the
BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the
correct polarity as marked, and screw the cover back on to the microphone. Make
sure the cover is screwed on completely. A fresh alkaline battery can last up to 16
hours in use, but in order to ensure optimum performance, it is recommended that
you replace the battery after every 10 hours of use.
2. Turn on the WHT-15 by sliding the OFF/ STANDBY/ ON SWITCH (20) to the
STANDBY position (transmitter on, audio muted) or the ON position (transmitter
and audio both on). The BATTERY INDICATOR LED (21) will give a single quick flash,
indicating usable battery strength. In the case of a dead or low battery, the LED will
either not go on at all or will stay on continuously, indicating that the battery should
be replaced with a fresh one. To preserve battery life, turn the transmitter off when
not in use.
21
20
17
3. The microphone is now ready to use. Most or all of the RF LEVEL DISPLAY
LEDs (4) on the Encore I receiver should now be lit, indicating a received signal
from the transmitter. When ready to speak, slide the transmitter switch to the ON
position. Adjust the volume of the receiver as per the Audio Output Microphone
Connection section of the above Encore I receiver instructions. The AF LEVEL
LED DISPLAY (5) on the Encore I receiver will light up to 5 LEDs (4 green and 1 red)
for all input signals. Occasional flickering on and off during use of the top red LED
indicator in this display is normal, however if the red LED stays on continuously,
it means the signal is too loud and there is the possibility of overload distortion. Back
off from the microphone until the red LED indicator only flickers on peaks.
21
20
[Note: Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback (howling or screeching) will be avoided.]
18
[Note: Microphone elements can easily be destroyed by the buildup of salts and
minerals from perspiration and saliva. It is good practice to put a windscreen on the
mic element at all times to protect it.]
19
17
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WLT-15 LAVALIER/ LAPEL OR HEADWORN MICROPHONE
BODYPACK TRANSMITTER
24
1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23),
observing the correct polarity. Close the compartment.
29
28
2. The WLT-15 is provided with a 3.5 mm LOCKING JACK (24) for connecting the
microphone. Plug in either the LAVALIER/ LAPEL (25) or the HEADWORN MICRO-
PHONE (26), as supplied. To secure the connection, turn the metal slip ring on the
plug clockwise to thread it on to the jack. To unplug, reverse the process. Slip the
transmitter into a pocket or clip on to your clothes. To use the lavalier mic, attach it at
chest level. Do not place too close to the mouth – a distance of about six inches
usually works best. To use the headworn mic, place it on the head and adjust the mic
boom so that the mic is about one inch to the side of the front of the mouth. (Note:
The lavalier or headworn mic wire is also the transmit antenna, and rolling up or
shortening the wire may reduce the effective operating range. Extend the wire fully
during use, and keep it as straight as possible.)
27
22
25
3. Turn on the WLT-15 by sliding the OFF/ STANDBY/ ON SWITCH (27) to the
STANDBY position (transmitter on, audio muted) or the ON position (transmitter and
audio both on). The BATTERY INDICATOR LED (28) will give a single quick flash,
indicating usable battery strength. In the case of a dead or low battery, the LED
either will not go on at all or will stay on continuously, indicating that the battery
should be replaced with a fresh one.
26
4. The microphone is now ready to use. Most or all of the RF DISPLAY LEDs (4) on
the Encore I receiver should now be lit, indicating a received signal from the
transmitter. When ready to speak, slide the transmitter switch to the ON position
and adjust the volume of the receiver as per the Audio Output Microphone
Connection section of the above Encore I receiver instructions. The AF LEVEL LED
DISPLAY (5) on the Encore I receiver will light up to 5 LEDs (4 green and 1 red) for
all input signals. Occasional flickering on and off during use of the top red LED
indicator in this display is normal, however if the red LED stays on continuously, it
means the signal is too loud and there is the possibility of overload distortion.
Re-position the microphone farther from the source or adjust the AUDIO INPUT
LEVEL CONTROL (29) until the red LED indicator flickers only on the loudest inputs.
[Note: Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback (howling and screeching) will be avoided.
Please also observe the pickup patterns of the microphone selected: omnidirectional
mics pick up sound equally from all directions and are prone to feedback if not used
carefully. Unidirectional mics are more resistant to feedback, but pick up sound
sources best that are directly in front of the mic. Also, mics that are farther from the
sound source, such as lavaliers, require more acoustic gain and thus are also more
prone to feedback than close-source mics such as handheld or headworn mics that
are used close to the mouth.]
22
Opening Battery Compartment
(Note: Microphone elements can easily be destroyed by the buildup of salts and
minerals from perspiration and saliva. It is good practice to put a windscreen on the
mic element at all times to protect it.)
23
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WGT-15 INSTRUMENT BODYPACK TRANSMITTER
32
35
1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31),
observing the correct polarity. Close the compartment. The WGT-15 is provided
with a 3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To
secure the connection, turn the metal slip ring on the plug clockwise to thread it on to
the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip on
to your clothes or instrument strap. (Note: As the cord to the instrument also serves as
the antenna, be sure to extend it fully for maximum range. Rolling up or shortening
the cord may reduce the effective operating range.)
34
33
32
30
2. Turn on the WGT-15 by sliding the OFF/ STANDBY/ ON SWITCH (32) to the
STANDBY position (transmitter on, audio muted) or the ON position (transmitter and
audio both on). The BATTERY INDICATOR LED (33) will give a single quick flash,
indicating usable battery strength. In the case of a dead or low battery, the LED
either will not go on at all or will stay on continuously, indicating that the battery
should be replaced with a fresh one.
3. The WGT-15 transmitter is now ready to use. Most or all of the RF DISPLAY LEDs
(4) on the Encore I receiver should now be lit, indicating a received signal from the
transmitter. Adjust the volume of the receiver as per the Audio Output Instrument
Connections section of the above Encore I receiver instructions. For optimum
performance, an INPUT LEVEL CONTROL (34) is provided on the top panel of the
WGT-15. Adjust the gain by turning the control with a small slot head screwdriver.
It is recommended that this control be turned to maximum gain. However, for ultra
high-gain instrument sources such as active bass pickups or even extra hot guitar
pickups, turning the level down slightly will create a cleaner sound. (Note: Turning
down the input gain too much can compromise the signal-to-noise ratio and is not
recommended. Set for the maximum possible gain and headroom without noticeable
distortion on the high level peaks).
The AF LEVEL LED DISPLAY (5) on the Encore I receiver will light up to 5 LEDs (4
green and 1 red) for all input signals. Occasional flickering on and off during use of
the top red LED indicator in this display is normal, however if the red LED stays on
continuously, turn down the instrument volume or adjust the INPUT LEVEL CONTROL
(34) on the WGT-15 transmitter, or noticeable distortion may result.
(Note: Scratchy noises can sometimes occur when some electric guitars/basses with
dirty pots or connections are used with any wireless system. For this reason, the
supplied INSTRUMENT CORD (35) has a factory installed capacitor inside the 1/
4" plug. This capacitor provides first order filtering of the RF signal from the cord
into the guitar and eliminates virtually all scratchy noises. Should your equipment still
give you scratchy noises, we suggest these steps to eliminate them:
1) Make sure all guitar volume and tone pots are clean and all contacts are
solid – this is very important.
30
Opening Battery Compartment
2) Provide extra filtering with a 220 pF capacitor soldered across the hot to
ground terminals of the guitar's volume and tone pots.)
31
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
THE LINK 2™ PLUG-IN TRANSMITTER
4. Microphone Operation
a. Turn on the Link 2 by sliding the ON/ STANDBY/ OFF SWITCH (41) to the
STANDBY position (transmitter on, audio muted) or the ON position (transmitter
and audio both on). The LOW BATTERY INDICATOR LED (40) will give a single
quick flash, indicating usable battery strength. In case of dead or low battery,
the indicator will either not go on at all or stay on continuously, indicating a
battery voltage below 7V. If this occurs, replace with fresh 9V battery. Remem-
ber to turn the transmitter off when not in use.
b. The Link 2 is now ready to use. Most or all of the RF DISPLAY LEDs (4) on the
Encore I receiver should now be lit, indicating a received signal from the
transmitter. When ready to speak, slide the transmitter switch to the ON position
and adjust the volume of the receiver as per the Audio Output Microphone
Connection section of the above Encore I receiver instructions. The AF LEVEL LED
DISPLAY (5) on the Encore I receiver will light up to 5 LEDs (4 green and 1 red)
for all input signals. Occasional flickering on and off during use of the top red
LED indicator in this display is normal, however if the red LED stays on continu-
ously, it means the signal is too loud and there is the possibility of overload
distortion. Re-position the microphone farther from the source or adjust the
Link 2 transmitter gain with the VOLUME LO/ HI GAIN SWITCH (39). Set for the
maximum possible level without noticeable distortion on the high level peaks. Set
the GAIN SWITCH to LO to decrease the audio level, and set the GAIN SWITCH
to HI to increase the audio level. The red LED indicator should flicker only on the
loudest inputs.
1. Transmitter Set-Up
First, slide open the BATTERY COMPARTMENT DOOR (43) to expose compartment.
Insert a fresh 9V ALKALINE BATTERY (45), observing polarity. Close the battery
compartment door.
2. Handheld Microphone Installation
• Step 1 - Rotate the transmitter's threaded LOCKING RING (37) clockwise
toward the XLR CONNECTOR (36) until it stops.
• Step 2 - Hold your mic in one hand and The Link 2 in the other.
• Step 3 - Plug your mic into the XLR CONNECTOR.
• Step 4 - Lock the mic into place with the adjustable threaded LOCKING RING
by rotating the ring, counterclockwise, to the top of the transmitter.
• Step 5 - To release the XLR CONNECTOR, turn the threaded LOCKING RING
clockwise and press the RELEASE BUTTON (44).
3. Lavalier Microphone Installation
The lavalier microphone you are using must terminate with an XLR connector and
conform to the pin assignments shown below. If it does not conform or is supplied
with a different connector, you must use an appropriate adapter or the lav mic may
not work with the Link 2. If you have any questions, please contact your Nady dealer
or Nady Systems’ Customer Service Department.
Note: The pin assignments on The Link 2’s XLR connector are as shown:
(Note: Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback (howling and screeching) will be avoided.
Please also observe the pickup patterns of the microphone selected: omnidirec-
tional mics pick up sound equally from all directions and are prone to feedback
if not used carefully. Unidirectional mics are more resistant to feedback, but pick
up sound sources best that are directly in front of the mic. Also, mics that are
farther from the sound source, such as lavaliers, require more acoustic gain and
thus are also more prone to feedback than close-source mics such as handheld
or headworn mics that are used close to the mouth.)
Ground
1
6.2K
3
XLR
Connector
Top View
2 6.5K
Phantom Volt. (full 9V battery
voltage) switchable
1
2
Mic
Input
3
(Note: Microphone elements can easily be destroyed by the buildup of salts and
minerals from perspiration and saliva. It is good practice to put a windscreen on
the mic element at all times to protect it.)
Note: Select phantom power, as needed, with the PHANTOM POWER ON/ OFF
SWITCH (42).
15
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
ENCORE I OVERALL SYSTEM PERFORMANCE
Frequency Response
Dynamic Range
25-20,000 Hz, +/-3dB
120dB
38
Total Harmonic Distortion
RF Carrier Frequency Range
Frequency Stability
Modulation
< 0.3%
169-216 MHz
+/- 0.005%, crystal controlled
FM (F3E), +/-20KHz max.
Up to 250 ft. typical (depending on site
conditions); up to 500+ feet optimum
line-of-sight
Operating Range
44
TRANSMITTERS
43
36
Audio Inputs
•WHT-15
•WLT-15/ WGT-15
Nady DM-10D neodymium dynamic cartridge
3.5mm mono locking jack for connecting to omni
or unidirectional lavalier mic or unidirectional
head worn mic, with phantom power (WLT-15);
or connecting to instrument cable (WGT-15)
Locking XLR jack for connecting to microphone or
cable, with selectable phantom power
37
41
39
•LINK 2™
Controls
•WHT-15
•WLT-15/ WGT-15
•LINK 2™
OFF/STANDBY/ON switch
OFF/STANDBY/ON switch, input level adjust
OFF/STANDBY/ON, LO/HI Level, and ON/OFF
Phantom power switch
Unit "ON" (single flash),
Low Battery Alert (steady)
50mW (Max. allowed by FCC)
> –40dB
40
42
LED Indicator
36
37
XLR Connector – Connects microphone to the transmitter module for signal input
Locking Ring – Locks microphone to the transmitter
RF Power Out
Harmonic & Spurious Emissions
Battery
Battery Life
Dimensions
•WHT-15
•WLT-15/ WGT-15
•LINK 2™
Weight (w/ o battery)
•WHT-15
•WLT-15/ WGT-15
•LINK 2™
38 Optional Pouch – For lavalier bodypack operation (with beltclip and strap ring for
9V Alkaline
Up to 15 hours
securing)
39
Gain Control Switch – Adjusts the input sensitivity (LO or HI)
Low Battery LED – Single flash (power on), lit steady (low battery)
Power Switch - Turns the power ON/STANDBY/OFF. In standby position, the power is
on and the audio is off.
9.5" X 1.4" Diam. (24.1 X 3.5 cm)
4.1" X 2.4"X 0.8" (10.4 X 6.1 X 2.0 cm)
4.5" X 1.5" X 1.25" (11.4 X 3.8 X 3.2 cm)
40
41
6.9 oz (193 g)
3.6 oz (101 g)
2.6 oz (71 g)
42
43
44
45
Phantom Power ON/ OFF Switch – Turns the phantom power ON/OFF
Battery Compartment
Release Button – Press to release XLR connector
9V Alkaline Battery
17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ENCORE I RECEIVER
Controls
Connectors
Power ON/OFF, volume control, mute control
Balanced XLR and unbalanced adjustable
1/4" audio out jacks, 2.1 mm barrel-type
DC input jack
LED Indicators
Dimensions (Max.)
Weight
Power ON, 5-LED RF & AF level displays ,
1.75" x 7.5" x 8.1" (4.4 x 19 x 20.7 cm)
1.6 lbs (.73 kg)
Power Requirements
12V @ 400mA, nominal,
AC/DC adapter supplied
11.2" (28.5 cm), single telescopic
Antenna
SERVICE
(U.S.) Should your Nady Encore I Wireless Microphone System require service,
please contact the Nady Service Department via telephone at (510) 652-2411 or e-
mail to [email protected] for a Return Authorization (R/A) Number and a
service quote (if out of warranty). Make sure the R/A Number is clearly marked on
the outside of the package and enclose a cashier’s check or money order (if not
prepaid with a credit card). Ship the unit prepaid to: Nady Systems, Inc., Service
Department, 6701 Shellmound Street, Emeryville, CA 94608. Include a brief
description of the problems you are experiencing.
The warranty card enclosed with this system contains additional valuable warranty
and service information. Keep it in a safe place for future possible reference. Do
not attempt to service this unit yourself as it will void the warranty.
(International) For service, please contact the Nady distributor in your country
through the dealer from whom you purchased this product.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Nady Wireless Systems are type accepted under FCC rules parts 90, 74 and 15. The
device complies with RSS-210 of Industry & Science Canada. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NADY SYSTEM S, INC.
6701 Shellmound Street • Emeryville, CA 94608 USA
Tel: 510/652-2411 • Fax: 510/652-5075
Download from Www.Somanuals.com. All Manuals Search And Download.
|