PULL
PULL
REAR OUTLETS
RACK LIGHTS
DIMMER
ON
STANDARD
VOLTAGE
OVER
VOLTAGE
MIN
MAX
OFF
POWER CONDITIONER & LIGHT MODULE
1800 WATTS CAPACITY
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls, functions, and connections
FRO N T PAN EL
PULL
PULL
REAR OUTLETS
RACK LIGHTS
DIMMER
ON
STANDARD
VOLTAGE
OVER
VOLTAGE
MIN
MAX
OFF
POWER CONDITIONER & LIGHT MODULE
1800 WATTS CAPACITY
1
6
2
3
5
6
4
2
1. POWER SWITCH
Outlet switch (with built-in LED ON indicator) activates protection and filtration to all back panel outlets. To turn
the unit ON or OFF, press the upper or lower portion of this button.
2. 2 RETRACTABLE RACK LIGHTS
Pull out for illumination and swivel to desired angle
3. LIGHT SWITCH
Activates rack illumination
4. DIMMER CONTROL
Use to control the intensity of the illumination. Turning clockwise increases the light output.
5. DIGITAL VOLTMETER READOUT
Displays incoming AC line voltage
6. VOLTAGE LED METER
Separate green and red LEDs monitor the incoming voltage range. The green LED indicates voltage is in the
normal operating range. The red LED lights when the voltage exceeds 125V, indicating that the supplied power
is out of range for normal operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PAN EL
8
9
7
7. POWER CORD
Heavy duty 14-guage power cord for connection to the AC power mains (~115V/ 60Hz)
8. CIRCUIT BREAKER
Resettable 15 amp thermal circuit breaker
9. 8 REAR PANEL OUTLETS
EMI/ RFI filtered, spike/ surge protected and switched
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and operation
1. The PCL Series conditioners are the perfect accessories for any rack mount system. Install in the top slot of a
standard 19-inch rack, and the 8 switched AC outlets on the rear panel will provide full safety protection to all
your rack equipment. These conditioners protect your delicate electronic equipment by combining a high
voltage varistor surge and transient suppressor with an RFI/ EMI interference filter. The filter helps prevent noise
from fluorescent lights, motors, and similar sources of “electronic pollution” from contaminating the AC feed to
your senitive video, audio, vtr or computer circuits.
2. Plug Power Cord (7) into a standard grounded 115V outlet
3. Plug sensitive electronic equipment into the 8 Rear Panel Outlets (9)
4. Turn Outlet Power Switch (1) to “ON” position. Lit LED indicates conditioned power to the connected
equipment.
5. For discreet illumination of your rack equipment on stage, in studios, and in other dark locations (PCL-
810/ 815 only), pull the 2 Retractable Rack Lights (2) out and adjust the Dimmer Control (4) for the lamp
brightness desired (see fig.1 below). The lights swivel and can be adjusted to the proper angle for your appli-
cation. The lamps are supplied with standard 5W night-light bulbs. If you find the heat from the bulbs exces-
sive, reduce the setting of the Dimmer Control or substitute lesser wattage bulbs. You can easily replace the
bulbs without removing the unit from the rack by unscrewing the cap on the end of each light tube. (Note: Be
careful not to push the tubes in while the caps are unscrewed.)
6. The Digital Voltmeter Readout (5) (PCL-815 only) is calibrated to a nominal 117 VAC at the factory.
No adjustments are necessary.
7. The Digital Voltmeter Readout (5) automatically displays incoming voltage when the Power Cord (7)
is connected.
8. MAXIMUM LOAD: The PCL Series Power Conditioners 8 Rear Panel Outlets are rated at 15 amps total load
(or 1800W at 120VAC). If this maximum load is exceeded, the Circuit Breaker (8) will trip, cutting off power
to all connected equipment in your rack. If this happens, reduce the load by unplugging one or more units
from the power conditioner, and push the circuit breaker to reset it (see fig.2 below).
fig.2
fig.1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
PROTECTION PROVIDED
High voltage varistor surge and transient suppressor,
RFI/ EMI interference filtration
8 standard 3-prong grounded AC receptacles
Maximum 1800W/ 15A load
~120VAC/ 60 Hz
OUTLET CONNECTORS
POWER CONSUMPTION
POWER SOURCE
CIRCUIT BREAKER
15A thermal type
LAMPS (PCL-810/ 815)
DIMENSIONS
5W (two)
19” X 1.75” X 7.3”
(483 X 44 X 185mm), 1U rack height
WEIGHT
PCL-800 4.45 lbs (2.0 Kg)
PCL-810 4.5 lbs (2.05 Kg)
PCL-815 4.55 lbs (2.07 Kg)
For improvement purposes, specifications, design and appearance subject to change without prior notice
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|