O w n e r ’ s M a n u a l
MGT
-
16
16-Channel Mini uHF
wireless Instrument system
Download from Www.Somanuals.com. All Manuals Search And Download.
System Features
MGT-16 system Features
MT-16a & MT-16r Transmitters
• UHF wireless system for guitar/bass
• Choice of two transmitter housings—
MT-16A with 30° angled ¼” plug for use
with either recessed or surface mounted
jacks, or MT-16R with 90° angled ¼” plug
for surface mounted jacks only
• 16 user-selectable PLL frequencies
for interference-free operation
• Up to 250’ operating range, line-of-sight
• Infrared ASC™ Auto-Sync Channel
transfer from receiver to transmitter
for instant setup
• Up to eight hours of battery life
from a single AAA alkaline or NiMH
rechargeable battery
• Battery operated receiver and transmitter
• Infrared channel sync with receiver
for instant setup
MGT-16 receiver
• Compact, portable,“pedal style” receiver
• Power On/Off switch; Power/Low Battery
LED indicators; IR Sync LED; Input level
attenuation switch; Internal audio level
control trim-pot
• Dual ¼ wave antennas
• Infrared sync with transmitter for
• External flexible antenna
instant setup
• Unbalanced ¼” line out jack
• Power On/Off/Mute switch;
Volume Control; LED indicators
for Power On, Low Battery, and
RF Reception; DIP-switch channel
selection with IR sync to transmitter
• Powered by DC adapter (included) or
two AA alkaline batteries for portability
(up to 8 hours battery life)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick User Controls Guide
MGT-16 Instrument receiver
7
8
9
IR PO LO RX
1
OFF ON
10
11
12
2
POWER
3
LEVEL
13
14
4
CHANNEL
ACT SQ
1
2
3
4
5
6
15
16
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. ASC™ IR SYNC INFRARED LED WINDOW
For downloading selected Channel
(Frequency) to transmitter
12. POWER ON LED Indicates the receiver is On
13. MUTE (SQUELCH) CONTROL Adjust with a small
screwdriver inserted in slot. Controls the
mute level for the receiver—turn counter-
clockwise for maximum range; turn clockwise,
if needed, to minimize noises from outside
RF interference upon muting.
2. POWER SWITCH Select OFF/MUTE/ON
(MUTE=power On, audio output highly
attenuated)
3. VOLUME CONTROL Adjusts the audio output
level—at maximum setting the gain will
be about +4dB over a direct instrument-to-
cord-to-amp connection
Note: Set control carefully. If trim-pot
is turned past minimum and maximum
adjustment points it may need to be backed
up to achieve desired setting.
4. CHANNEL SELECT DIP-SWITCH Select one of
16 pre-set channels per MGT-16 DIP-Switch
Frequency Selection Chart (see page 14)
5. BATTERY COMPARTMENT Insert two AA
batteries for optional DC operation,
note correct polarity
14. ASC™ IR SYNC BUTTON Press to make the IR link
download the receiver’s selected frequency to
the TX. First, turn on the MT-16A/R transmitter
(or turn off and then on again if already on) and
position its IR window 6-12” away from the
RX IR window, press the SYNC button once
and wait one second for the RX to respond.
If the IR data download is successful, the
receiver SIGNAL LED (10) will light indicating
the transmitter is locked in and transmitting.
15. AA BATTERIES Two required for optional battery
operation
6. BATTERY COMPARTMENT COVER
7. AUDIO OUTPUT JACK For connecting audio cable
8. DC INPUT JACK For connecting external AC/DC
adapter for powering receiver
9. ANTENNAS Dual ¼ wave
10. SIGNAL LED Indicates the received signal
from the transmitter
16. POWER ADAPTER For AC operation (included)
11. LOW BATTERY LED Indicates batteries need
replacement (if not using power adapter)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick User Controls Guide
MT-16a/r Instrument Transmitter
19
MT-16R
(Straight plug)
MT-16A
(Angled plug)
18
17
20
21
22
23
26
24
25
17. POWER SWITCH To power transmitter Off/On
18. 15dB ATTENUATION PAD Select to reduce the
input gain by 15dB for higher level audio
input signals
23. INTERNAL AUDIO LEVEL ADJUST Remove battery
to access slot and adjust internal trim-pot
with small screwdriver for optimal input
level setting. Note: this is to be done only in
rare cases as factory level setting is already
optimized for most guitars and basses and
15dB Pad also available.
19. INPUT ¼” PLUG Connect directly into
guitar/bass output jack
20. LOW BATTERY LED Indicates battery
needs replacement
Note: Set control carefully. If trim-pot
is turned past minimum and maximum
adjustment points it may need to be backed
up to achieve desired setting.
21. IR RECEPTOR SENSOR/WINDOW Infrared LED
sensor for linking the TX to the RX during
IR frequency download
24. ANTENNA Permanently attached antenna
25. BATTERY Single AAA alkaline or NiMH battery
required for operation
22. BATTERY COMPARTMENT Insert one AAA
battery, observing correct polarity
26. BATTERY COMPARTMENT COVER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ir sync selected Frequency Download
from MGT-16 receiver to MT-16a/r Transmitter
(1) ASC™ IR SYNC INFRARED LED WINDOW
For downloading selected Channel
(Frequency) to transmitter
14
IR PO LO RX
1
(21) IR RECEPTOR SENSOR/WINDOW Infrared LED
OFF ON
POWER
sensor for linking the TX to the RX during
IR frequency download.
ACT SQ
14. ASC™ IR SYNC BUTTON Press to make the IR link
download the receiver’s selected frequency to
the TX. First, turn on the MT-16A/R transmitter
(or turn off and then on again if already on) and
position its IR window 6-12” away from the
RX IR window, press the SYNC button once
and wait one second for the RX to respond.
If the IR data download is successful, the
receiver SIGNAL LED (10) will light indicating
the transmitter is locked in and transmitting.
21
System Operation
MGT-16 wireless Instrument receiver
it is recommended that the batteries
be replaced after six hours of use, or as
antennas
The MGT-16 receiver is supplied with
indicated by the low Battery Indicator (11).
As the batteries begin to weaken below
usable voltage, the low battery indicator
will light up continuously, warning that the
batteries are now too low and should be
replaced as soon as possible. To preserve
battery life, keep the receiver Off when it
is not in use.
Dual antennas (9) attached. They should be
extended fully to obtain maximum range.
The optimal positions of the antennas are
45 degrees from the receiver and 90 degrees
from each other. For maximum range, it is
always best to maintain a line-of-sight (no
obstructions) between the receiver antennas
and the transmitter whenever possible.
For AC operation, power the receiver with
the supplied aC Power adaptor (16). Plug the
adapter’s barrel plug into the DC Input Jack (8)
on the back of the receiver, then plug the
adapter into an AC outlet.
Powering the receiver
The MGT-16 receiver can operate with either
two AA size batteries (DC operation) or with
the supplied AC adaptor (AC operation).
AC operation of the MGT-16 receiver is
the same as DC operation except that the
Low Battery Indicator is inactive when the
AC adapter is connected.
For DC operation, open the receiver’s
Battery Compartment Door (6) and place
two fresh AA batteries in the battery
compartment, observing the correct polarity.
Two fresh alkaline or NiMH AA batteries will
generally provide 6-8 hours performance,
but in order to ensure optimal performance
Note: When the AC adapter is used, the installed
batteries are automatically disconnected internally
and are not operational. The AC adapter only
7
Download from Www.Somanuals.com. All Manuals Search And Download.
powers the unit and will not charge NiMH
rechargeable batteries if installed. For battery
operation the AC adapter must be disconnected.
selecting the MGT-16 receiver
Channel and Ir sync
The Frequency select DIP switches (4)
are used for selecting one of 16 preset
frequencies. Simply position the DIP
Note: For quietest optimal performance, use
the AC/DC adapter as battery operation raises
the noise floor around 4 dB. Generally this is
only a concern when playing high-gain lead
guitar. For such applications, experiment to see
if slightly quieter performance with the AC/DC
supply is preferred.
switches to a desired open channel on the
receiver. There should be no flickering of
the rF signal leD (10) with the transmitter
off. See the MGT-16 DIP-Switch Frequency
Selection Chart on page 14 for the correct
switch position for each of the 16 available
channels. Once you have selected
the receiver frequency it can easily be
downloaded to the transmitter to establish
the necessary RF connection. For help in
finding open channels, see RF Interference
and Finding Open Channels on page 12.
Turn on the MGT-16 receiver by sliding
the Power switch (2) to the second position
(receiver On but audio output Muted/
Attenuated), or to the third position for
normal operation (receiver On and audio
un-Muted). The Power leD (12) will light up
and the receiver is operational.
The Ir sync Button (14) on the MGT-16 receiver
is used to transfer the selected frequency
info from the receiver to the transmitter for
quick synchronization prior to use. Begin
programming by holding the wireless
transmitter’s Ir receptor/sensor window (21)
about 6-12” from the receiver’s Ir synch
Infrared leD window (1). Press the IR Sync
Button once to begin the IR sync download
of the selected frequency to the transmitter.
adjusting the squelch
The rF squelch (13) control should be
adjusted counterclockwise to the minimum
RF squelch setting at which the rF signal
leD (10) remains on while your transmitter is
in normal use, up to the maximum operating
range anticipated in use for your application.
However, in areas of high RF activity, the
squelch control may need to be adjusted
clockwise. If the transmitter is off and the
receiver RF Signal LED indicator is flickering
or stays on continuously, the squelch should
be adjusted to a higher level (clockwise
for less mute sensitivity level) to stop the
flickering. Be careful not to select too high
a clockwise setting as this may reduce the
operating range to below what is needed.
A range walk test will help in selecting
the proper level. If the range is not critical,
note that a clockwise (maximum squelch)
setting will also yield a quieter mute
Note: To insure proper synchronization, the
transmitter must always be just turned on, or
else turned of then on again before synching.
function, which may be desirable in certain
applications. The squelch level is factory
preset at maximum sensitivity and operating
range (i.e. counterclockwise for minimum
squelch/maximum usable range).
IR PO LO RX
OFF ON
6-12”
POWER
LEVEL
CHANNEL
ACT SQ
Note: Set controls carefully. If trim-pots are turned
past minimum or maximum adjustment points
they may need to be backed up to achieve
desired setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MT-16a/r Instrument Transmitter
When the rF signal leD (10) on the receiver
lights up, the system frequency is properly
synchronized. To change to a different
frequency, reset the Frequency select DIP
switches (4) and sync the transmitter again
to the new selected frequency first, after
turning the transmitter off and then on
again. If no action is taken during the 10
seconds of active data transfer ( i.e., the
transmitter is not turned on or properly
positioned) the receiver and the transmitter
units do not link and transmitter’s previously
programmed channel remains unchanged.
Powering the Transmitter
The MT-16A/R Instrument transmitter
requires one aaa size battery (25). To install
the battery, push the locking tabs on the
Battery Cover (25) and push out to expose
the Battery Compartment (22). Insert one
fresh AAA battery according to the correct
polarity as indicated on the transmitter
body. Close the battery cover, ensuring the
cover is snapped shut. A fresh AAA alkaline
battery generally provides up to 6-8 hours
of operation, but in order to ensure optimal
performance it is recommended that the
battery be replaced after six hours of use or
as indicated by the low Battery Indicator (20).
Note: Only one transmitter can be used with one
receiver. It is not possible to use two transmitters
on the same frequency and mix the output of
these transmitters into one wireless receiver.
Note: The IR link is infrared light and works best
when this data transfer is accomplished in a
light-shielded or darker environment. It may not
be successful in a brightly lit area. If the transfer
fails, repeat the procedure in a darker location
or somehow shield the link from outside light to
successfully program the transmitter with the
selected channel info from the receiver.
To turn on the transmitter, slide the
Power switch (17) in the direction of the
arrow. The Low Battery Indicator will
flash once. The unit is now on and the
receiver’s rF signal leD (10) will light up
if the transmitter has been frequency
synchronized to the receiver’s selected
frequency as per below.
Connecting audio Output
As the batteries weaken, the Low Battery
Indicator will flash to warn that the battery
level is too low and should be replaced as
soon as possible. To preserve battery life,
turn the transmitter Off when not in use.
To turn the transmitter Off, slide the Power
Switch in the opposite direction of the arrow.
The MGT-16 receiver’s audio Output Jack
(7) is a ¼”unbalanced line out and its level
is controlled by the Volume Knob (3). Plug
an audio cable with a ¼” mono (tip/sleeve)
plug into the audio output jack and plug the
other end into your pedal board or amplifier
as you would with a direct cord from the
instrument. When the Volume knob is
set to maximum receiver volume setting,
the system audio output is approximately
+4dB higher than a direct instrument-to-
cord-to-amp connection.
The transmitter has a 15dB Pad (18) On/Off
switch which can be selected to attenuate
high output instrument pick-up levels if
needed to reduce distortion through the
system. To turn On, slide the switch in the
direction of the arrow. Turning opposite the
arrow indication is for standard 1:1 gain
operation and is recommended for normal,
optimal low-noise operation.
Note: As when making any connection, make sure
the amplifier volume control is set at the minimum
level before plugging in the receiver to avoid
possible speaker damage.
Your MGT-16 receiver is now operational
and ready to use. Once you have completed
the above steps, proceed to the following
instructions for the MT-16A/R Instrument
transmitter.
The transmitter has an Internal audio
level adjust (23) to set the audio deviation
level. It is accessed by inserting a small
screwdriver into the slot. Turning this
9
Download from Www.Somanuals.com. All Manuals Search And Download.
trim-pot counterclockwise reduces overall
system audio output (thus lowering
distortion but raising background noise),
while turning clockwise increases overall
system audio output (thus lowering
background noise but raising distortion). The
Audio Level Adjust is factory set to the mid
position, which is the optimal setting for
normal operation.
When programming is finished, close the
battery compartment door, ensuring that it
latches. The MT-16A/R is now ready for use.
note: Manually matching the transmitter frequency
without the receiver is not possible. For proper
operation, the transmitter must have the same
channel as selected on the receiver.
Operating the MT-16a/r
Instrument Transmitter
note: The Audio Level Adjust is not intended for
high-input signal adjustment—the 15dB pad is
provided for that purpose. It is for use only in
extreme cases during which satisfactory audio
cannot be achieved with the pad alone.
During normal operation with the unit
powered On, the MT-16A/R transmitter
should be fully inserted onto the instrument
(guitar, bass, etc.). When ready to play,
slide the Power switch (2) to On position
in the direction of the arrow. The receiver
signal leD (10) should light up if system is
properly synchronized. Adjust the volume
on the receiver (see Connecting Audio
Output on page 9) for unity gain (one-to-
one) with a hard-wired cord. Or, select up
to an added 4-5dB boost by adjusting the
receiver volume to maximum for normal use
with guitars and bass guitars. A listening
test prior to use will determine which
receiver volume and transmitter input pad
settings are best for your application. To
Mute/un-Mute (attenuate) the audio during
use, set the receiver power switch to the
second (Mute) position. Or, just turn off the
transmitter with the Transmitter Power switch
(17). The Signal LED will turn off and the
audio will be muted (Off). When ready to
play again, slide the receiver’s power switch
to the third (On) position. Or, just turn on
the transmitter.
Note: Set control carefully. If trim-pot is turned past
minimum or maximum adjustment points, it may
need to be backed up to achieve desired setting.
Programming the MT-16a/r
to the selected Channel
Before beginning operation, the MT-16A/R
transmitter must be synchronized with
the selected frequency from the receiver
using the Ir receptor/sensor window (21) on
the transmitter and the Ir sync window (1)
on the receiver (see Selecting the MGT-16
Receiver Channel and IR Sync on page 8).
After first turning the transmitter on (or
off and then on again if already on), begin
programming by holding the transmitter’s
IR Receptor/Sensor Window about 6-12”
from the receiver’s IR Synch Window. Press
the Ir sync Button (14) once to begin the IR
sync download of the selected frequency
to the transmitter. Upon successful data
transfer (usually in less than two seconds)
the transmitter will transmit a radio signal
on the same channel (frequency) as
the receiver. The signal leD (10) on the
receiver will light up, indicating that the
link is completed. If all the necessary steps
noted above are not taken during the ten
seconds of active data transfer, the receiver
and the transmitter units will not link and
the transmitter’s previously programmed
channel remains unchanged.
Note: While playing, the audio level should be
adjusted on the instrument as when using a
hard-wired cord.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
MGT-16 sysTeM
Frequency response
Dynamic range
50Hz–16kHz (-3dB)
120dB
Oscillating system
Total Harmonic Distortion (THD)
rF Carrier Frequency range
Modulation
Phase Lock Loop (PLL)
<0.8%
902.40MHz–923.70MHz
FM (F3E), +/-30KHz normal
Up to 250 feet (typical, depending on site conditions)
Operating range
MGT-16 reCeIVer
Controls
Audio Level, Power ON/MUTE/OFF,
Frequency Select DIP-switches, IR sync button
Unbalanced ¼”, DC Adapter input jack
Power ON (Red-continuous), Low Power (Orange-continuous),
RX reception (Green)
Connectors
leD Indicators
antennas
Dual ¼ wave, adjustable orientation
>105dB (w/AC/DC power supply)
-110dBm nominal, 12dB SINAD
-95dBm (minimum/normal setting), adjustable
1.0KΩ
signal-to-noise ratio
receiver sensitivity
squelch sensitivity
Output Impedance
Power Consumption
Battery
DC: 3V/ 115mA or AC/DC adapter: 10VDC/200mA
Two AA alkaline or NiMH
Battery life
Up to 8 hours
Dimensions
weight (w/o batteries)
Housing Construction
2.75” W x 5.00” D x 1.88” H (7.0 cm x 12.7 cm x 4.78 cm)
5.7 oz (161.6 g)
ABS Plastic
MT-16a/r TransMITTer
rF Power Out
25mW nominal, 50mW maximum
Harmonic & spurious emissions
Controls
-50dB
Power ON/OFF, 15dB Attenuation Pad select switch
leD Indicators
Input Impedance
Power Consumption
Battery
Power ON (Red-single flash), Low Battery (Red flash)
500KΩ
DC 1.5V/90mA
One AAA alkaline
Up to 8 hours
Battery life
antenna
¼ wave, permanently attached
Dimensions
MT-16A: 4.5” W x 2.0” D x 1.0” H (11.43 cm x 5.08 cm x 2.54 cm)
MT-16R: 3.5” W x 2.5” D x 1.0” H (8.9 cm x 6.35 cm x 2.54 cm)
MT-16A: 1.2 oz (34 g)
weight (w/o batteries)
MT-16R: 1.1 oz (31.2 g)
Housing Construction
ABS Plastic
Specifications subject to change at any time without prior notice for purposes of product improvement
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions and Troubleshooting
no or low audio
If you are not getting audio through the system, carefully re-check all setups. Especially
note that the receiver and transmitter must be set to operate on the same RF channel.
Make sure that the receiver Power switch (2) on the MGT-16 receiver is not in the second
position (audio muted/attenuated). The receiver’s unbalanced audio Out (7) is adjustable,
so make sure the Volume Control (3) is set properly.
rF Interference and Finding Open Channels
If you encounter slight receiving interference when the transmitter is far from the receiver,
it can often be overcome by adjusting the receiver‘s squelch adjust (13) (see Adjusting the
Squelch on page 8). If you receive interference on a selected channel with the transmitter
Off, you must reprogram the receiver and transmitter to a different channel.
To reprogram, you must first find an open channel. To do this, follow the operating
procedure outlined in Selecting the MGT-16 Receiver Channel and IR Sync on page
8. With the transmitter Off, change the receiver DIP switches setting to one of the
16 channels until you find one for which the signal leD (10) doesn’t flicker or light up.
Also, for optimal interference-free operation, the Signal LED must not flicker or light up
on any of the three immediately adjacent channels, both above and below the selected
channel (i.e., a field of seven adjacent channels, with the chosen channel in the middle,
should all be clear). If operating multiple MGT-16 systems simultaneously, repeat
this procedure every time a new channel is selected, with all other transmitters and
receivers turned on.
It is important to note that wireless frequencies are shared with other radio services.
According to current FCC regulations, wireless microphone operation is not protected from
interference from other licensed operations in the band. If any interference is received
by a government or non-government operation and wireless microphone use is deemed
responsible for the interference, the wireless microphone must cease operation or change
frequencies. Note: This requirement is applicable in the U.S. only.
Note: If the Signal LED is lit, this indicates good signal strength in operation. If the Signal LED remains
lit with the transmitter Off, this indicates the presence of likely RF interfering signals at that location.
Should this occur, select a different channel.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous Tips
• The receiver antennas should be kept
away from any metal surfaces whenever
possible as they can reflect away or shield
the incoming RF signal.
Keep antennas away from noise sources
such as motors, automobiles, neon light,
signal processors, computers, and large
metal objects.
• When inserting batteries, make sure they
• A receiver cannot receive signals from
are inserted with the correct polarity.
two or more transmitters simultaneously.
• Before operation, confirm that the receiver
and associated transmitter are tuned to
the same frequency/channel.
• Turn the transmitter off when it is not in
use. For longest life, remove the batteries
if the unit is not going to be used for a
long period of time as the transmitters
draw a tiny residual current even when
off in order to maintain the programmed
settings. Also, since batteries installed
for a long time can sometimes corrode
and/or leak, causing damage, it is
• After making a receiver channel change,
make sure that the corresponding change
is also made on the matching transmitter.
• Use only fresh alkaline or fully charged
NiMH batteries. Do not use “general
purpose” carbon batteries. When batteries
are weak, replace all of them at the same
time. Do not mix new and old batteries,
or different types of batteries.
generally recommended that batteries
be removed whenever the transmitters
are not being used.
• When using the MT-16A/R with guitars
and basses: Scratchy noises can
sometime occur when electric guitars
with dirty pots or connections are used
with a wireless system. If you hear
scratchy noises, we suggest these steps
to eliminate them:
• Position the receiver so it has the least
possible obstructions between it and the
transmitter. Line-of-sight is best.
• During operation, the transmitter and
receiver should be as close as possible
to each other for optimal results.
• Although placement of the receiver on
the floor provides good performance in
most applications, for best operation the
receiver should be placed at least 3 feet
(1 meter) above the ground and 3 feet
(1 meter) away from a wall or metal
1) Make sure all guitar volume and tone pots
are clean and all contacts are solid. This is
very important.
2) Consider soldering a 47pF capacitor
across the pot to ground terminal of the
guitar’s volume and tone pots—this will
provide extra filtering.
surfaces. The transmitter should also be
at least 3 feet (1 meter) from the receiver.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MGT-16 DIP-Switch
Frequency Selection Chart
Frequency Plan: 902.4MHz-923.7MHz (16 Channels) u.s.
Channel selection Frequency
Channel selection Frequency
1
2
3
4
5
6
7
8
902.4
904.8
905.4
906.7
907.8
909.8
910.8
911.2
9
913.9
914.0
916.0
917.9
919.7
920.0
921.1
923.7
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
10
11
12
13
14
15
16
Accessories
Part number
Description
AC-MGT-16
10VDC/200mA AC/DC receiver power supply adapter included
Service Information
In the u.s. If you are experiencing operational problems with your system, please refer to
service, please contact the Nady Service Department at (510) 652-2411 to obtain a Return
Authorization (R/A) Number and service quote (if out of warranty). Make sure the R/A
Number is clearly marked on the outside of the package that you are returning.
If your unit is out of warranty, please enclose a cashier’s check or money order (or pay
by credit card) per instructions by the Nady Service Department. Ship your unit prepaid
to: Nady Systems, Service Department, 6701 Shellmound Street, Emeryville, CA 94608.
Include a brief description of the problem you are experiencing. For service of a unit under
warranty, please follow the instructions in the following section.
Outside the u.s. For service or warranty matters please contact the Nady distributor in your
country through the dealer/store from which you purchased this product.
Do not attempt to service this unit yourself as
it can be dangerous and will also void the warranty.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
One-Year Limited Warranty
Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects
in material or workmanship for a period of one year from the date of original retail purchase. If any such
defect is discovered within the warranty period, Nady Systems, Inc. will repair or replace the unit free of
charge, subject to verification of the defect or malfunction upon return to Nady Systems. Please do not
return your Nady product to the store where it was purchased as Nady Systems handles your warranty
service directly. Communication with our Service Department is the most efficient means of servicing
your unit and we are dedicated to keeping you a satisfied customer.
To the extent permitted by law, any applicable implied warranties, including warranties of merchantability
and fitness are hereby limited to one year from the date of purchase. Consequential or incidental
damages resulting from a breach of any applicable express or implied warranties are hereby excluded.
This warranty is in lieu of all other agreements and warranties, general or special, express or implied
and no representative or person including a Nady dealer, agent, or employee is authorized to assume
for us any other liability in connection with the sale or use of this Nady Systems’ product.
Whereas some states do not allow limitations on how long implied warranties last, and do not allow
exclusion of incidental or consequential damages, the above limitations and exclusions may not apply
to you. This warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.
This warranty is subject to the following conditions:
1) This system must have been purchased from an authorized Nady dealer and all warranty
service must be performed by Nady’s service department. Any service not performed by Nady
will automatically void this warranty.
2) Items not covered: physical damage resulting from improper handling of the unit in transit from the
factory by the shipper (Nady Systems is not responsible for such damage and all such claims must be
made against the shipping company by the consignee); defects caused by normal wear of the product
(expendable parts are typically connectors, cables, potentiometers, switches and similar components);
damage or defects caused by abuse, neglect, accident, failure to connect or operate the unit in any way
that does not comply with applicable technical or safety regulations, or improper repair, excessive heat
or humidity, alteration or unreasonable use of the unit, causing cracks, broken cases/housings or parts;
damage caused by leaking batteries; finish or appearance items; items damaged in shipment en route to
Nady Systems, Inc. for repair. The warranty is null and void if any Nady serial number has been removed
or defaced.
How To Obtain service:
1) If factory service is required, please contact our Service Department at (510) 652-2411 for a return
authorization (R/A) number. Make sure the R/A number is clearly marked on the outside of your package.
(Please note: if an R/A number is not included, our Shipping Department cannot accept your package.)
2) Send the unit back to Nady Systems, 6701 Shellmound Street, Emeryville, CA, 94608, freight pre-paid.
You must include proof of date and place of purchase (i.e., photocopy of your bill of sale) or Nady cannot
be responsible for repair or replacement. Nady Systems, Inc. will not repair, nor be held responsible,
for any units returned without proper identification, return address, and R/A number clearly marked
on the package.
3) Per the above, Nady will perform all warranty service and return the unit to you at no charge.
Nady Systems will inform the buyer if product sent in does not meet the terms of this warranty
and will provide a quote for fixing the unit and/or shipping it back exclusively at the buyer’s expense.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|
6701 Shellmound Street Emeryville, CA USA 94608
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|