iW1, iW2, iW3
In-Wall Loudspeakers
OWNER’S MANUAL
Now Hear This
527 Stone Road
Benicia, CA 94510
800-NHT-9993
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for purchasing NHT in-wall loudspeakers. Please take a few minutes to read through this Owner's Manual prior to installing
your new speakers. The information provided will help you to obtain maximum performance from your audio system. If you have ques-
tions or need assistance at any time during the installation or operation of your new speakers, please call your NHT Dealer or our Toll-
Free Customer Hotline at:
1-800-NHT-9993
„
Design
NHT loudspeakers are designed to deliver refined, musical sound from attractive and affordable packages. Our efforts are guided by
the study of human hearing and are optimized for real world use. Every NHT speaker undergoes rigorous testing and quality control at
the factory to ensure you years of listening pleasure.
NHT in-wall loudspeakers are designed to deliver the sonic performance and value of NHT’s freestanding loudspeakers, while offering
the invisibility of in-wall installation. The custom designed drive units are mounted in a rigid baffle assembly designed to minimize the
audible effects of unwanted vibrations and resonance. The mounting assembly is designed to be intuitive and flexible, making it ideal
for new or existing construction. With high performance sonics and a paintable face, NHT in-wall loudspeakers are the perfect solution
for architectural audio and home theater installations.
Caution: In-wall loudspeakers should be installed by an experienced and licensed custom
installation professional. Be sure that the installer possesses sufficient skill, the proper tools,
knowledge of local fire and building codes, and a familiarity with the structure of the building
(especially wall and/or ceiling materials, layouts, electrical and plumbing lines, etc.).
„
Placement
NHT in-wall loudspeakers are designed for in-wall installation between standard 2” x 4” wood studs. Installation in outdoor locations or
in moisture-prone interior environments such as indoor swimming pools or saunas is not recommended.
Spend some time considering speaker placement prior to installing the NHT in-wall loudspeaker. Once the speakers are installed, they
are permanent, so their location should be selected carefully. Mount the speakers in a location where they face the listening area with-
out obstruction from furniture, and preferably at least three feet from side walls. The speakers should be mounted on a flat wall surface
to ensure a good seal between the speaker assembly and the wall. For best sonic performance, position the speakers so that the dis-
tance between the primary listening position and the wall is 1.5 times the distance between the two speakers (fig.1). To get an idea how
they will look in the room, try taping the supplied cutout templates to the wall. Keep in mind that room furnishings play an important role
in absorbing and reflecting soundwaves. Midrange and high frequencies in particular will be absorbed by soft furnishings such as sofas,
carpets and curtains. A large number of these soft furnishings will tend to dull the sound somewhat, while a “live” room with few fur-
nishings tends to brighten the sound.
D
NHT in-wall loudspeakers are not magnetically shielded, do not install them in a
Center of
Speaker
Plane
location where they will be within 12” of a direct view television. Unshielded
magnets placed in close proximity to a television screen can cause picture dis-
coloration and may damage the picture tube. When installing three NHT in-wall
1.5 x D
loudspeakers for front channels in a home theater system, you can position the
fig.1
L & R speakers farther apart to create a wider soundstage. When installing NHT
in-wall loudspeakers as center channel speakers, they should be installed at
least 12” directly above or below the location where the television will be.
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing List:
Baffles
1 pair of baffles
1 pair of frames
iW1
iW2
iW3
1 pair of metal grilles
2 cutout template/paint shields
iWB mounting bracket includes:
(optional, purchased seperatly)
(1) Mounting bracket
(2) Mounting wings
(4) 5 x 50mm flathead screws
Tools Needed:
#2 Philips screwdriver
Pencil
iWB
(optional)
Tape measure
Utility knife or keyhole saw
Level
Wire strippers
Safety goggles
Protective gloves
Grille
Mounting Bracket
Mounting
Wing
Tech Tips: Pre-Wiring for New Construction
1. For best results, avoid running speaker wire near AC wire, as it may induce a 60Hz hum in the audio signal. It’s a good idea to run
the speaker wire after the AC wiring has already been completed, so that you can route the speaker wire at least three feet away from
the AC wiring. If speaker wire and AC wiring must run parallel, install the speaker wire within a steel conduit. Note that low voltage
wiring (doorbell, intercom, telephone, security, etc.) is unlikely to induce hum and can typically be run parallel to speaker cable with no
detrimental effects.
2. When drilling holes through wall studs or ceiling joists, use a drill bit that is at least as wide as the speaker cable that will be routed
through them. Always drill through the center of the stud or joist. If the hole must be drilled within one inch of the edge of a wall stud,
add a nail plate to the drywall side to protect the cable from possible nails and screws put in the wall later. Line up the holes in the
studs or joists as you go, so that pulling the cable through them will be easier.
Download from Www.Somanuals.com. All Manuals Search And Download.
„
Installation: New Construction
(unfinished walls)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
fig.2
1. Begin by installing the iWB mounting bracket between adjacent studs.
NHT in-wall loudspeakers should only be used in the vertical orientation
(fig.5). Attach the mounting wings to the bracket by inserting them into the
locking plastic tabs in the side of the bracket (fig.2).
1
2
1
2
3
4
1
2
1
2
3
4
2. Select the desired location for the speaker, using a level to ensure that it
is precisely positioned. The wings feature progressively elongated sections
(1”, 1”, 2”, 2”, 2”, 3”, 3”) with screw holes spaced in one-inch increments.
Attach the wings to the studs with the 5 x 50mm flathead screws or staples.
For maximum stability, use two screws for each wing. Bend back the extra
portion of the wing at one of the “break” lines (fig.3).
Bend
Bend
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1 4
1 3
1 2
1 1
0 1
3
4
1 5
2 6
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
3. Complete the pre-wiring before the drywall goes up (see “Tech Tips: Pre-
Wiring for New Construction”). Leave an extra few feet of speaker wire, and
secure it close to the mounting bracket
fig.3
Studs
4. During the drywall phase, cut a hole 10 1/4” high by 8 1/8” wide around
the bracket. When installled, the frame will extend out about 1 inch beyond
the perimeter of the cutout to hide minor imperfections in the cutout.
5. If the NHT in-wall loudspeaker assembly and grille are to be painted to
match the room color, paint them now before installing the baffle (see
“Painting”).
Frame
6. After the drywall is complete, install the frame. The frame attaches to the
bracket via six plastic mounting clamps on the back of the frame that swivel
to “sandwich” the drywall between the speaker assembly and the clamps
(fig.4). First rotate the mounting clamps inward so that the body of the frame
can slide through the mounting bracket. Tighten the screws snugly, making
sure not to over tighten, as this may compromise the fit of the frame. The
gasket on the drywall side of the speaker assembly lip reduces unwanted
vibrations against the drywall and will compress slightly to allow the frames
lip to rest flush against the ceiling. The spring loaded mounting clamps pro-
vide tension once installed.
Mounting
Clamp
fig.4
7. Connect the speaker wire to the spring posts on the back of the baffle,
making sure to observe correct polarity (see “Connections”).
8. Put the baffle into the frame so the holes on the baffle line up with the
holes in the center of the raised bosses on the frame (fig. 5). Push each 4 x
16mm screw through the holes on the baffle and into the hole on the frame
and tighten it by hand temporarily so that the baffle and the frame stay togeth-
er. Once all the screws are started, tighten each of them snugly, making sure
not to overtighten, as this may compromise the fit of the baffle. The use of
power screwdrivers is not recommended. Exercise caution to not damage the
drivers when inserting the screws.
fig.5
9. Remove the protective cover from the tweeter/midrange bridge.
10. Attach the metal grille by inserting it into the grooves in the baffle.
Tweeter /
Midrange
Bridge
Download from Www.Somanuals.com. All Manuals Search And Download.
Tech Tips: Optimizing Sonic Performance
Bass response is smoothest when the speaker is mounted within a rigid wall that flexes very little. For improved perfor-
mance, add 2”x4” cross-braces horizontally roughly one foot above and one foot below the speaker location. Use wood
glue and extra screws when attaching the drywall to the studs around the speaker. Additionally, once the speaker cutout
has been made in the drywall, add a bead of wood glue inside the wall where the drywall meets the studs and cross-
braces. If possible, use two layers of drywall for maximum rigidity.
For an easier option, use NHT’s Acoustic Foam Insert Kit. The kit contains flame retardant, dense foam blocks that stiff-
en the drywall and can be added after the drywall is up. See your NHT dealer for details.
For more controlled bass response, add insulation to the wall cavity around and behind the speaker to provide acoustic
damping. Be sure to add the same amount of insulation to speakers in the same room to ensure consistent sound. Use
R-12 or R-19 fiberglass insulation, and be sure to wear protective gloves to avoid contact with the fibers. If the insulation
is paper- or foil-faced, position the paper or foil side away from the speaker.
„
Installation: Existing or New Construction
(retrofitting finished walls)
Warning: Exercise caution when drilling into existing walls. Do not drill through existing wires,
pipes, conduits, heating or air conditioning ducts. If you feel resistance while drilling, stop
immediately.
1. Using a studfinder or the “knocking” method, locate the wall studs in the wall area where you wish to mount the speaker. The speak-
er should be installed between adjacent studs, no closer than two inches from either stud (fig.6).
2. Determine that there are no obstructions behind the desired cutout
area. This may be accomplished by drilling a hole in the center of the
cutout area and using an “L”-shaped piece of metal (like a coat hang-
fig.6
Cut
er) to “feel around” behind the wall. If you discover an obstruction, fill
the hole with patching compound and try another location.
3. If there are no obstructions found behind the wall, use the supplied
cutout template and a pencil to draw a 10 1/4”H x 8 1/8”W outline of
the area to be cut out. Use a level to ensure that the cutout is pre-
cisely positioned. Begin by drilling the four corners with a 1/4” bit
Drill
(fig.6). Then cut out the wall section with a utility knife or keyhole saw,
following the lines traced around the mounting template. If the wall is
painted or wallpapered, use the keyhole saw.
4. If the wall is constructed of lath and plaster, outline the penciled
marks with masking tape, drill the four corners with a 1/4” drill bit, and
use a utility knife to cut through the plaster down to the lath. Use a
saber saw with a metal cutting blade or a pair of tin snips to gently cut
Download from Www.Somanuals.com. All Manuals Search And Download.
through the lath, being careful not to vibrate plaster off the wall.
5. If the frame and grille are to be painted in the wall, paint now before
installing the baffle (see “Painting”).
Frame
6. Now install the frame. The frame attaches to the wall (or iWB brack-
et) via six plastic mounting clamps on the back of the frame that swiv-
el to “sandwich” the drywall between the speaker assembly and the
clamps (fig.7). First rotate the mounting clamps inward so that the
body of the frame assembly can slide through the wall. Tighten the
screws snugly, making sure not to over tighten, as this may compro-
mise the fit of the frame. The gasket on the drywall side of the frame
reduces unwanted vibrations against the drywall and will compress
slightly to allow the frames lip to rest flush against the wall. The spring
loaded mounting clamps provide tension once installed.
Mounting
Clamp
fig.7
7. Connect the speaker wire to the spring posts on the back of the baf-
fle, making sure to observe correct polarity (see “Connections”).
8. Put the baffle into the frame so the holes on the baffle line up with
the holes in the center of the raised bosses on the frame (fig. 8). Push
one of the 4 x 16mm screws through a hole on the baffle and into the
hole on the frame and tighten it by hand so that the baffle and the
frame stay together. Insert the remaining screws, then tighten all of
them snugly, making sure not to overtighten, as this may compromise
the fit of the baffle. The use of power screwdrivers is not recommend-
ed. Exercise caution not to damage the drivers when inserting the
screws.
9. Remove the protective cover from the tweeter/midrange bridge.
10. Attach the metal grille by inserting it into the grooves in the baffle.
fig.8
Tweeter /
Midrange
Bridge
Download from Www.Somanuals.com. All Manuals Search And Download.
„
Painting
fig.9
The frame and grille are painted in a matte white finish that may be
painted to match the wall. The baffle must be removed before
installing the paint shield. Keep in mind that the grille contains hun-
dreds of tiny holes that are essential to the sound of the speaker. Take
care not to clog these holes with paint.
Paint
Shield
Fold down
outer ring
Remove
Baffle
1. Remove the baffle from the frame by removing the six screws and
carefully separating the baffle from the frame.
2. Paint the frame and the grille at the same time using the same
paint. Use the supplied paint shield (fig.9) to protect the hole from
overspray. Fold the corners down and insert the paint shield into the
grooves where the grille would attach. Be careful not to punch
through the round hole in the middle of the shield.
Place Inside
Frame
3. When using spray paint, apply two thin coats, making sure to let the
first coat dry completely before applying the second. This will avoid
runs. When using a compressor and spray gun, apply the paint using
its finest setting. Painting with a brush is not recommended, but when
necessary be sure to thin the paint so it does not cover the holes in
the grille. If paint does cover any of the grille holes, poke them out
with a paper clip.
Ready to
paint
4. Once painting is complete, remove the paint shield from the bezel by carefully punching out the round hole in the middle, and using
this hole to pull the shield free.
5. Reinstall the baffle. Do not attempt to paint the black baffle surface (which houses the drivers) behind the grille. Its black finish pre-
vents the speaker’s black drive units from being visible once the grille is attached.
„
Connections
Before connecting speakers to your system, it is important that you turn off the power to your amplifier / receiver to avoid dam-
age to the equipment. Before installing the speaker, map out the wiring paths between the speakers and the amplifier. Make
sure that the speaker wire does not rest on sharp or pointed objects.
The NHT in-wall loudspeaker is compatible with virtually all quality amplifiers. Proper wiring of the speakers is essential to good sound.
At a minimum, 16AWG 2-conductor speaker wire is recommended for runs of 10 feet or less, with heavier special purpose speaker cable
used for longer runs. For best results, use equal length runs of wire for the left and right speakers. When permanently installing wire
inside walls, be sure to use wire that is rated for in-wall use and has special jacketing for fire prevention. In the U.S., the U.L.
standard is CL-2, CL-3 and CM wire, and in Canada the CSA standard is FT4 wire. The wire should be run in accordance with
National Electrical Code and any applicable local building codes. Prepare the wire by stripping 1/4” to 3/8” of insulation from the
ends and twisting the exposed wire strands tightly. The spring loaded binding posts on the back of the speaker will accept raw wire only.
Be sure to wire both the left and right speakers "in-phase." That is, the Positive + (red) terminal on the amplifier output must
be connected to the corresponding Positive + (red) terminal on the speaker. Likewise with the Negative - (black) terminals.
All speaker wire have some sort of marking along one or both conductors to help you make the correct connections. Incorrect speaker
phase is indicated by weak bass and the lack of a well-defined stereo image.
Download from Www.Somanuals.com. All Manuals Search And Download.
„
Operation
NHT in-wall loudspeakers are designed to handle a wide range of listening levels, but every speaker has limits. It is important to use
common sense and listen for signs of possible distress from the speakers. Underpowered amplifiers are most often the cause of speak-
er damage. For example, a 60-watt amplifier runs out of power when called upon to produce more than 60 watts, and the resulting dis-
tortion can damage the speaker. If you tend to listen at high volume levels, more powerful amplifiers are preferable because they are
less likely to run out of power.
Noticeable distortion or harsh breakup is an indication that either your amplifier or your speakers are running beyond their capacity, and
the volume should be decreased. If you can feel any heat emanating from the woofer or tweeter, reduce the level immediately. Speaker
damage most often occurs from sustained high volume levels, not from transient sounds or brief musical peaks. Excessive boosting of
bass, treble or equalizer controls can worsen the problem, and is not recommended.
„
Maintenance
NHT in-wall loudspeakers require minimal maintenance under normal use. The grille and frame may be cleaned using a damp cloth or
a mild, non-abrasive cleaner. Do not expose the speaker to direct sunlight, high temperatures, or moisture. Do not attempt to clean the
actual drivers.
Limited Warranty
Valid Only in the U.S.A.
Warranty Period
For the period of 5 years for parts and 5 years for labor from date of original purchase (the warranty period) from an autho-
rized NHT dealer, Now Hear This (NHT) warrants that if our product fails to function properly under normal use due to a man-
ufacturing defect when installed and operated according to the owner’s manual instructions enclosed with the unit, it will be
repaired or replaced with a unit of comparable value at the option of NHT without charge to you for parts or actual repair work.
Parts supplied under this warranty may be new or rebuilt at the option of NHT.
What’s Not Covered
This warranty does not cover any product which is used in any trade or business, or in an industrial or commercial applica-
tion.
This warranty does not cover the cabinet or any appearance item, or any damage caused to the product resulting from: alter-
ations, modifications not authorized in writing by NHT, accident, misuse or abuse, damage due to lightning or power surges,
or being subjected to power in excess of the speaker’s published power rating.
This warranty does not cover the cost of parts which would otherwise be provided without charge under this warranty, obtained
from any source other than an authorized NHT service location. This warranty does not cover defects or damage caused by
the use of unauthorized parts or labor or from improper maintenance.
Altered, defaced or removed serial numbers void this warranty.
Your Rights
The liability of NHT will be limited to the purchase price of the product, and NHT will not be liable for incidental or consequential
damages. NHT limits its obligations under any implied warranties under state laws to a period not exceeding the warranty
period. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclu-
sion or limitation of incidental or consequential damages. The above limitations or exclusions may not apply to you. This war-
ranty gives you specific legal rights, and you may have other rights which vary from state to state.
To Obtain Service
NHT has appointed a number of authorized service companies throughout the USA should your product ever require service.
To receive warranty service, you will need to present your sales receipt showing place and date of original owner’s transac-
tion.
To find the name and address of the nearest authorized NHT service location, call or write: Customer Service Department,
Keep this warranty with your sales receipt. Record date and place of purchase for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|