JGS516_JGS524_IG.fm Page 1 Tuesday, January 3, 2012 4:42 PM
19-Inch Rack Mounting
Installation
Installation Guide
Use the rack-mount kit supplied with
your switch.
Estimated time: 5–10 Minutes
1. Use the Phillips head screws to
fasten the mounting brackets to
the sides of the switch. Tighten
the screws with a No. 1 Phillips
screwdriver.
Select a Location
ProSafe® 16-port or 24-port Gigabit Switch JGS516 V2 or
JGS524 V2
Decide where you want to place the switch. Find a flat horizontal surface or a
19-inch rack.
Package Contents
Make sure that the location is:
2. Align the bracket and rack holes.
Use two pan-head screws with
nylon washers to fasten each
bracket to the rack. Tighten the
screws with a No. 2 Phillips
screwdriver to secure the switch
in the rack.
•
•
Not in direct sunlight or near a heater or heating vent.
Verify that all items are in the box. The package includes:
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear
space on all sides of the switch.
•
•
•
•
•
ProSafe® 16-port or 24-port Gigabit Switch JGS516 V2 or JGS524 V2
Power cord with localized plug
•
Well ventilated, especially if it is in a closet.
Adhesive feet
Install the Switch
Rack-mount brackets and hardware
Installation Guide (this document)
Troubleshooting
1. For each device that you want to connect to the switch, provide an enhanced
Category 5 (Cat 5e) Ethernet cable with RJ-45 connections. Each Ethernet
cable has to be less than 328 feet (100 meters) long.
You can use the LEDs to troubleshoot hardware problems.
Front View
2. Install the switch on a flat surface or in a standard 19-inch rack.
Power LED Is Off
•
Flat surface. The switch comes with four self-adhesive footpads. Stick one
footpad on each of the four concave spaces on the bottom of the switch. The
footpads cushion the switch against shock and vibrations.
The switch has no power.
•
•
Make sure that the power cord is securely connected to the switch.
•
Rack mounting. Follow the instructions in the 19-Inch Rack Mounting
section.
Make sure that the power cord is connected to a functioning power outlet. If it is
connected to a power strip, make sure that the power strip is turned on. If the
socket is controlled by a light switch, make sure the switch is in the on position.
Verify Cable Connections
24 Gigabit ports for the JGS524,
or 16 for the JGS516
LEDs
Port LED Is Off for a Connected Device or Stays On Continuously
Before you apply power, perform the following checks:
1. Inspect the equipment thoroughly.
There is a hardware connection problem.
The switch supports 10 Mbps, 100 Mbps, and 1000 Mbps connections. Using
Gigabit Ethernet (1000 Mbps), the switch sends files across the network at speeds
up of to 2000 Mbps due to the full duplex nature of Gigabit Ethernet connections.
The switch supports straight-through or crossover Ethernet cables. Each port on the
switch configures itself based on the cable that you plug into it. Depending on the
model, you can use the switch to connect either up to 24 or 16 Ethernet devices
such as computers, file servers, printers, routers, switches, or hubs.
2. Verify that all cables are installed correctly.
•
Make sure that the cable connectors are securely plugged in to the switch and
the device.
3. Check cable routing to ensure that cables are not damaged and will not create
•
•
Make sure that the connected device is turned on.
a safety hazard.
If the Ethernet cable is connected to a network interface card or other Ethernet
adapter, make sure that the card or adapter is installed correctly and is working.
4. Be sure that all equipment is mounted securely.
•
Make sure the cable is less than 328 feet (100 meters) long.
Download from Www.Somanuals.com. All Manuals Search And Download.
|