Contents
Conventions, Formats and Scope ..................................................................................... v
Chapter 1
Introduction
Package Contents ..........................................................................................................1-3
Chapter 2
Physical Description
GS108T Front and Back Panel Configuration ................................................................2-1
System LEDs ...........................................................................................................2-3
Device Hardware Interfaces ...........................................................................................2-3
RJ-45 Ports ..............................................................................................................2-3
Powered-Device Port ...............................................................................................2-3
Reset Button ............................................................................................................2-4
Chapter 3
Applications
Contents
iii
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Step 1: Preparing the Site ..............................................................................................4-1
Step 2: Installing the Switch ...........................................................................................4-2
Step 5: Applying Power ..................................................................................................4-4
Using an AC Power Source .....................................................................................4-4
Appendix A
Additional Troubleshooting Suggestions ....................................................................... A-2
Auto-Negotiation ..................................................................................................... A-3
Appendix B
iv
Contents
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
The NETGEAR ProSafeTM GS108T Hardware Installation Guide describes how to install and
power on the GS108T Smart Switch. The information in this manual is intended for readers with
intermediate computer and Internet skills.
®
Conventions, Formats and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•
Typographical Conventions. This manual uses the following typographical conventions:
Italic
Emphasis, books, CDs, file and server names, extensions
User input, IP addresses, GUI screen text
Command prompt, CLI text, code
URL links
Bold
Fixed
italic
•
Formats. This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.
v
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Danger: This is a safety warning. Failure to take heed of this notice may result in
personal injury or death.
•
Scope. This manual is written for the GS108T Smart Switch according to these specifications:
Product Version
GS108T Smart Switch
January 2010
Manual Publication Date
Note: Product updates are available on the NETGEAR, Inc. website at
How to Print this Manual
Your computer must have the free Adobe Acrobat reader installed in order to view and print PDF
files. The Acrobat reader is available on the Adobe Web site at
•
•
Printing a PDF Chapter. Use the PDF of This Chapter link at the top left of any page.
–
Click the PDF of This Chapter link at the top left of any page in the chapter you want to
print. The PDF version of the chapter you were viewing opens in a browser window.
–
Click the print icon in the upper left of your browser window.
Printing a PDF version of the Complete Manual. Use the Complete PDF Manual link at the
top left of any page.
–
Click the Complete PDF Manual link at the top left of any page in the manual. The PDF
version of the complete manual opens in a browser window.
–
Click the print icon in the upper left of your browser window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
vi
About This Manual
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Revision History
Version
Number
Part Number
Date
Description
202-10248-01 1.0
202-10562-01 1.0
March 2007
Initial release
January 2010
Hardware v2.0 and new software features including:
• DoS protection
• DHCP filtering
• Voice VLAN
• Auto-VoIP
• DiffServ
• MAC filtering
• Protected ports
• MAC and standard/extended IP ACLs
About This Manual
vii
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
viii
About This Manual
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Congratulations on the purchase of your GS108T Gigabit Smart Switch. The GS108T Smart
Switch is a state-of-the-art, high-performance, IEEE-compliant network solution designed for
users who require a small desktop switch and want the power of Gigabit connectivity to eliminate
bottlenecks, boost performance, and increase productivity. To simplify installation, the switch is
shipped ready for use out of the box.
This chapter serves as an introduction to the GS108T Smart Switch and provides the following
information:
•
•
•
Overview
This Installation Guide is for the GS108T Gigabit Smart Switch. This product offers support for
eight 10/100/1000 Mbps auto-sensing ports.
Using Gigabit ports, high-speed connections can be made to a server or network backbone. For
example:
•
•
Linking to high-speed servers
Providing 10/100/1000 Mbps copper connectivity
The GS108T Smart Switch also provides the benefit of administrative management with a
complete package of features for the observation, configuration, and control of the network. With a
Web-based Graphical User Interface (GUI), the switch’s many capabilities can be viewed and used
in a simple and intuitive manner. The switch’s management features include configuration for port
and switch information, VLAN for traffic control, port trunking for increased bandwidth, and
Class of Service (CoS) for traffic prioritization. These features provide better understanding and
control of the network. Initial discovery of the switch on the network requires the Smart Control
Center program, a utility that runs on a PC.
1-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
The GS108T Smart Switch is a free-standing switch. It is IEEE-compliant and offers low latency
for high-speed networking. All ports can automatically negotiate to the highest speed. This
capability makes the switch ideal for environments that have a mix of Ethernet, Fast Ethernet, or
Gigabit Ethernet devices. In addition, all RJ-45 ports operate in half-duplex or full-duplex mode.
The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair
(UTP) cable.
Features
The following list identifies the key features of the GS108T Smart Switch.
•
•
•
Eight RJ-45 10/100/1000 Mbps auto sensing Gigabit switching ports.
The devices support full NETGEAR Smart Switch functionality.
The devices provide full compatibility with IEEE standards:
•
•
•
•
•
IEEE 802.3i, (10BASE-T)
IEEE 802.3u (100BASE-TX)
IEEE 802.3ab (1000BASE-T)
IEEE 802.3x (Full-duplex flow control)
IEEE 802.3af (Power over Ethernet)
•
•
•
Auto-sensing and auto-negotiating capabilities for all ports.
Auto Uplink™ on all ports to make the right connection.
Automatic address learning function to build the packet-forwarding information table. The
table contains up to 4K Media Access Control (MAC) addresses.
•
•
•
•
•
•
•
Store-and-Forward transmission to remove bad packets from the network.
Full-duplex IEEE 802.3x pause frame flow control.
Active flow control to minimize packet loss/frame drops.
Half-duplex back-pressure control.
Per port LEDs, power LED.
NETGEAR Green product series.
External 12V/1A PA or power obtained from IEEE 802.3af PSE.
1-2
Introduction
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Green Features
The GS108T Smart Switch supports the following power-saving features:
•
•
The power consumption automatically adjusts based on the RJ-45 cable length.
Each port is configured to automatically power down when the port link is down.
Package Contents
Figure 1-1 shows the package contents of the GS108T Gigabit Smart Switch.
Figure 1-1
Verify that the package contains the following:
•
•
•
•
GS108T Gigabit Smart Switch
Rubber footpads for tabletop installation
Wall mounting screws (2)
External power supply
Introduction
1-3
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
•
•
Installation guide
Smart Switch Resource CD with Smart Control Center utility and User’s manual
If any item is missing or damaged, contact the place of purchase immediately.
1-4
Introduction
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Physical Description
This chapter describes the GS108T Gigabit Smart Switch hardware features. Topics include:
•
•
•
GS108T Front and Back Panel Configuration
The GS108T Smart Switch is an eight-port 10/100/1000 Mbps Smart Switch. Every RJ-45 port is
capable of sensing the line speed and negotiating the operation duplex mode with the link partner
automatically
Figure 2-1 illustrates the NETGEAR GS108T Smart Switch front panel:
Link/Speed/ACT LEDs
Power/Status LED
10/100/1000 Mbps Ethernet Ports
Figure 2-1
The front panel contains the following:
•
•
•
•
•
Eight RJ-45 connectors for 10/100/1000 Mbps auto-sensing Gigabit Ethernet switching ports
Reset button to restart the device
Recessed default reset button to restore the device back to the factory defaults
Link, Speed, and Activity LEDs for each port
Power and Status LED
2-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Figure 2-2 illustrates the NETGEAR GS108T Smart Switch back panel:
Power Connector
Figure 2-2
The back panel contains a DC input for the supplied 12V/1A external power adapter.
LED Designations
Port LEDs
The following table describes the port LED designations.
Table 2-1. Port LEDs
LED
Designation
100 Mbps Link/ACT (Left LED)
• Off - No 100 Mbps link is established on the port.
• Solid Green - A valid 100 Mbps link is established on the port.
• Flashing Green - Packet transmission or reception is occurring on
the port at 100 Mbps.
10 Mbps Link/ACT (Right LED)
• Off - No 10 Mbps link is established on the port.
• Solid Green - A valid 10 Mbps link is established on the port.
• Flashing Green - Packet transmission or reception is occurring on
the port at 10 Mbps.
1000 Mbps Link/ACT (Both LEDs) • Off - No 1000 Mbps link is established on the port.
• Solid Green - A valid 1000 Mbps link is established on the port.
• Flashing Green - Packet transmission or reception is occurring on
the port at 1000 Mbps.
2-2
Physical Description
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
System LEDs
The following table describes the system LED designations.
Table 2-2. System LEDs
LED
Designation
Power/Status LED
• Solid Green - Power is supplied to the switch and is operating normally.
• Solid Yellow - The switch is booting.
• Off - Power is disconnected.
Device Hardware Interfaces
RJ-45 Ports
RJ-45 ports are auto-sensing ports. When inserting a cable into an RJ-45 port, the switch
automatically ascertains the maximum speed (10, 100, or 1000 Mbps) and duplex mode (half-
duplex or full-duplex) of the attached device. All ports support only unshielded twisted-pair (UTP)
cable terminated with an 8-pin RJ-45 plug.
To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This
technology allows attaching devices to the RJ-45 ports with either straight-through or crossover
cables. When inserting a cable into the switch’s RJ-45 port, the switch automatically:
•
•
Senses whether the cable is a straight-through or crossover cable.
Determines whether the link to the attached device requires a “normal” connection (such as
when connecting the port to a PC) or an “uplink” connection (such as when connecting the
port to a router, switch, or hub).
•
Configures the RJ-45 port to enable communications with the attached device, without
requiring user intervention. In this way, the Auto Uplink technology compensates for setting
uplink connections, while eliminating concern about whether to use crossover or straight-
through cables when attaching devices.
Powered-Device Port
The NETGEAR GS108T Smart Switch is a PoE Powered Device (PD) and can receive power
from PoE Power Sourcing Equipment (PSE). To power the GS108T Smart Switch from a PoE
power source, such as the NETGEAR GS748TPS ProSafe Gigabit Stackable PoE Smart Switch,
you can connect the PSE to Port 1 on the GS108T Smart Switch through a standard Cat5 UTP
cable. This allows the GS108T Smart Switch to be powered by PoE.
Physical Description
2-3
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Reset Button
The Smart Switch has a Reset button on the front panel to allow you to manually reboot the switch.
This action is equivalent to powering the unit off and back on. The last saved configuration is
loaded into the switch as it resets. To operate the Reset button, insert a device such as a paper clip
into the opening to press the recessed button. The front-panel LEDs should extinguish and light
again as the switch performs its Power On Self Test (POST).
Factory Defaults Button
The Smart Switch has a Factory Defaults button on the front panel so that you can remove the
current configuration and return the device to its factory settings. When you enable the Factory
Defaults button, all settings, including the password, VLAN settings, and port configurations will
be set to the factory default values. To operate the Factory Defaults button, insert a device such as
a paper clip into the opening to press the recessed button for at least two seconds.
2-4
Physical Description
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Applications
Your GS108T Gigabit Smart Switch is designed to provide flexibility in configuring your network
connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps
hubs and switches.
Desktop Switching
The GS108T Smart Switch can be used as a desktop switch to build a small network that enables
users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port
connected to the server or PC can provide 2000 Mbps throughput.
Internet
Server
Firewall
`
`
`
`
Desktop PCs
Figure 3-1
3-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
3-2
Applications
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Installation
This chapter describes the installation procedures for your GS108T Gigabit Smart Switch. Switch
installation involves the following steps:
Step 1: Preparing the Site
Before you install the switch, ensure the operating environment meets the site requirements in the
following table.
Table 4-1. Site Requirements
Characteristics Requirements
Mounting
• Desktop installations - Provide a flat table or shelf surface.
• Wall-mount installations - Wall-mount: select a location. You also need the mounting
screws supplied with your switch.
Access
Locate the switch in a position that allows access to the front panel RJ-45 ports, view the
front panel LEDs, and access the power connector.
4-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Table 4-1. Site Requirements (continued)
Characteristics Requirements
Power source
Provide a power adapter (included). Power specifications for the switch are shown in
Appendix A . Ensure the AC outlet is not controlled by a wall switch, which can
accidentally turn off power to the outlet and the switch.
Alternatively, you can use IEEE802.3af-compliant power sourcing equipment (PSE) to
supply power to the switch. Connect the PSE to Port 1 on the GS108T switch.
When both an external power supply and a PoE source are connected to the GS108T
switch, the external power source takes priority.
Environmental
• Temperature - Install the switch in a dry area, with ambient temperature between 0 and
50ºC (32 and 122ºF). Keep the switch away from heat sources such as direct sunlight,
warm air exhausts, hot-air vents, and heaters.
• Operating humidity - The installation location should have a maximum relative
humidity of 90%, non-condensing.
• Ventilation - Do not restrict airflow by covering or obstructing air inlets on the sides of
the switch. Keep at least 2 inches (5.08 centimeters) free on all sides for cooling. Be
sure there is adequate airflow in the room or wiring closet where the switch is installed.
• Operating conditions - Keep the switch at least 6 ft. (1.83 m) away from nearest
source of electromagnetic noise, such as a photocopy machine.
Step 2: Installing the Switch
The GS108T Smart Switch can be used on a flat surface or mounted on the wall.
Installing the Switch on a Flat Surface
The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the
four concave spaces on the bottom of the switch. The rubber footpads cushion the switch against
shock/vibrations.
Wall Mounting the Switch
To mount the switch on a wall (optional), install the two provided screws in positions that
correspond to the slots on the bottom side of the GS108T, then mount the switch.
4-2
Installation
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Step 3: Checking the Installation
Before applying power to the switch, perform the following:
•
•
•
•
Inspect the equipment thoroughly.
Verify that all cables are installed correctly.
Check cable routing to make sure cables are not damaged or creating a safety hazard.
Ensure all equipment is mounted properly and securely.
Step 4: Connecting Devices to the Switch
The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The GS108T
Smart Switch contains Auto Uplink technology, which allows the attaching of devices using either
straight-through or crossover cables.
`
`
Desktop PC
Desktop PC
Figure 4-1
(Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these
connections.
Note: Ethernet specifications limit the cable length between the switch and the attached
device to 100 m (328 ft.).
Installation
4-3
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Step 5: Applying Power
The GS108T Smart Switch does not have an ON/OFF switch. You can apply or remove power by:
•
•
Connecting or disconnecting the power adapter to or from an AC power source
Connecting or disconnecting Port 1 to or from a PoE power source.
Note: When both an external AC power source and a PoE power source are connected to
the GS108T switch, the external AC power source takes priority.
Using an AC Power Source
Before connecting the power cord, select an AC outlet that is not controlled by a wall switch,
which can turn off power to the switch. After selecting an appropriate outlet, use the following
procedure to apply AC power.
1. Connect the end of the supplied IEC AC power adapter cable to the power receptacle on the
back of the switch.
2. Connect the AC power adapter cable into a power source such as a wall socket or power strip.
When applying power, the Power LED on the switch’s front panel illuminates.
If the Power LED does not go on, check that the power cable is plugged in correctly and that the
Using a PoE Power Source
The NETGEAR GS108T Smart Switch is a PoE Powered Device (PD) and can receive power
from IEEE 802.3af-compliant PoE Power Sourcing Equipment (PSE). To power the GS108T
Smart Switch through PoE, use the following procedures:
1. Connect a standard Cat5 UTP cable to Port 1 (also labeled PoE-PD) on the front of the switch.
2. Connect the other end of the Cat5 cable to the appropriate port on the PoE Power Sourcing
Equipment (PSE).
When applying power, the Power LED on the switch’s front panel illuminates.
If the Power LED does not go on, check that the power cable is plugged in correctly and that the
4-4
Installation
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Step 6: Managing the Switch using a Web Browser or the PC
Utility
The GS108T Smart Switch contains software for viewing, changing, and monitoring the way it
works. This management software is not required for the switch to work. The ports can be used
without using the management software. However, the management software enables the setup of
VLAN and Trunking features and also improves the efficiency of the switch, which results in the
improvement of its overall performance as well as the performance of the network.
After powering up the switch for the first time, the Smart Switch can be configured using a Web
browser or a utility program called Smart Control Center. For more information about managing
the switch, see the GS108T Software Administration Manual on the Smart Switch Resource CD.
Note: When the device powers up, there is a default IP address already configured on the
device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0.
Installation
4-5
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
4-6
Installation
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Troubleshooting
This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics
include the following:
•
•
Troubleshooting Chart
The following table lists symptoms, causes, and solutions of possible problems.
Table A-1. Troubleshooting Chart
Symptom
Cause
Solution
Power LED is off.
No power is received.
If you are using AC power, check the power cord
connections for the switch at the switch and at the
power source (such as the wall socket or power
strip). Ensure all cables used are correct and comply
with Ethernet specifications.
If you are using a PSE, verify that the Ethernet cable
between the switch and the PSE is good. Make sure
the cable does not exceed the maximum length
supported by the PSE. Make sure the PSE has not
exceeded the amount of power it can provide to all
connected devices.
Link LED is off or
intermittent.
Port connection is not
working.
Check the crimp on the connectors and make sure
that the plug is properly inserted and locked into the
port at both the switch and the connecting device.
Ensure all cables used are correct and comply with
Ethernet specifications. Check for a defective NIC on
the connected device. Check for a defective cable or
port by testing them in an alternate environment
where all products are functioning.
Troubleshooting
A-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Table A-1. Troubleshooting Chart
Symptom
Cause
Solution
File transfer is slow or
Half-duplex or full-duplex Make sure the attached device is set to auto-
performance degradation setting on the switch and negotiate.
is a problem.
the connected device are
not the same.
A segment or device is
One or more devices are Verify that the cabling is correct. Ensure all
not recognized as part of not properly connected,
connectors are securely positioned in the required
the network.
or cabling does not meet ports. Equipment may have been accidentally
Ethernet guidelines.
disconnected.
ACT LED is flashing
continuously on all
connected ports and the been created.
network is disabled.
A network loop
(redundant path) has
Break the loop by ensuring that there is only one
path from any networked device to any other
networked device.
Additional Troubleshooting Suggestions
If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the
troubleshooting suggestions in this section.
Network Adapter Cards
Ensure the network adapter cards installed in the PCs are in working condition and the software
driver has been installed.
Configuration
If problems occur after altering the network configuration, restore the original connections and
determine the problem by implementing the new changes, one step at a time. Ensure that cable
distances, repeater limits, and other physical aspects of the installation do not exceed the Ethernet
limitations.
Switch Integrity
If required, verify the integrity of the switch by resetting the switch. To reset the switch, remove
the AC power from the switch and then reapply AC power. If the problem continues, contact
NETGEAR technical support. In North America, call 1-888-NETGEAR. If you are outside of
North America, please refer to the support information card included with your product.
A-2
Troubleshooting
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Auto-Negotiation
The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the
link supports auto negotiation. If the device does not support auto negotiation, the switch only
determines the speed correctly and the duplex mode defaults to half-duplex.
The gigabit port on the Gigabit module negotiates speed, duplex mode, and flow control, provided
that the attached device supports auto-negotiation.
Troubleshooting
A-3
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
A-4
Troubleshooting
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Technical Specifications
Network Protocol and Standards Compatibility
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x flow control
IEEE 802.3af
Management
Windows 2000 + XP, Vista; Microsoft Explorer 6.0 or higher
IEEE 802.1Q VLAN
IEEE 802.3ad Link Aggregation
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1W Rapid Spanning Tree Protocol
IEEE 802.1X Port Security
IEEE 802.3ab LLDP
SNMP v1, v2c, and v3
HTTP and HTTPS
Port Mirroring (RX, TX, and Both)
IGMP Snooping v1/v2/v3
IEEE 802.1p Class of Service (CoS)
SNTP (Simple Network Time Protocol) 2 servers. Disabled by default.
Jumbo Frame Support
Technical Specifications
B-1
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Interface
Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all
ports).
LEDs
Per port (Gigabit): Link/Activity, Speed
Per device: Power
Performance Specifications
Forwarding modes: Store-and-forward
Bandwidth: 16 Gbps
Address database size: 4K media access control (MAC) addresses per system
Mean Time Between Failure (MTBF): 278,553 hours (~32 years)
Power Supply
Power Consumption: 8.5W maximum
100-240VAC/50-60 Hz universal input
Physical Specifications
Dimensions (H x W x D): 27 x 158 x 105 / 1.1 x 6.2 x 4.1 (mm/in)
Weight: 0.56/1.23 (kg/lbs)
Environmental Specifications
Operating temperature: 0°C to 50°C (32 to 122°F)
Storage temperature: -20°C to 70°C (28 to 158°F)
Operating humidity: 10%-90% maximum relative humidity, non-condensing
Storage humidity: 5%-95% maximum relative humidity, non-condensing
Operating altitude: 3,000 m (10,000 ft.) maximum
Storage altitude: 3,000 m (10,000 ft.) maximum
B-2
Technical Specifications
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
Electromagnetic Emissions
FCC Class B
CE mark, commercial
CE Class B, include EN55022 (CISPR 22) / 55024 / 50082-1
VCCI Class B
C-Tick
KCC
Safety
CE mark, commercial
UL listed (UL 1950)/cUL IEC950/EN60950
CB and CCC
Technical Specifications
B-3
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GS108T Hardware Installation Guide
B-4
Technical Specifications
v1.0, January 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|