e. Turn on your computer, connect the power adapter to the WAG302 and verify
the following:
Deploy the WAG302
)NSTALLATION 'UIDE
WAG302 ProSafe Dual Band Wireless Access Point
•
Power: The power light should be lit. If the power light is not lit, check the
connections and check to see if the power outlet is controlled by a wall
switch that is turned off.
1. Disconnect the WAG302 and position it where you will deploy it. The best location is
elevated, such as wall mounted or on the top of a cubicle, at the center of your
wireless coverage area, and within line of sight of all the mobile devices.
•
•
Test: The test light blinks when the WAG302 is first turned on.
Start Here
2. Position the antenna. Vertical positioning provides best side-to-side coverage.
Horizontal positioning provides best top-to-bottom coverage.
LAN: The LAN light on the WAG302 should be lit (amber for a 10 Mbps
connection and green for a 100 Mbps connection). If not, make sure the
Ethernet cable is securely attached at both ends.
Please refer to the Reference Manual on your Resource CD for instructions on advanced
3. Connect an Ethernet cable from your WAG302 Access Point to a LAN port on your
router, switch, or hub.
configuration options.
Estimated Completion Time: 30 minutes.
•
Wireless: The WLAN lights (e.g., 802.11a and 802.11g) should be lit.
4. Connect the power adapter to the wireless access point and plug the power adapter in
to a power outlet. The PWR, LAN, and Wireless LAN lights should light up.
Tip: Before mounting the WAG302 in a high location, first set up and test the WAG302 to
verify wireless network connectivity.
2. Configure LAN and Wireless Access
Tip: The WAG302 supports Power Over Ethernet (PoE). If you have a switch that
provides PoE, you will not need to use the power adapter to power the WAG302. This
can be especially convenient when the WAG302 is installed in a high location far
away from a power outlet.
a. Configure the WAG302 Ethernet port for LAN access.
First, Set Up the WAG302
•
Connect to the WAG302 by opening your browser and
1. Connect the wireless access point to your computer and
modem
Now, Verify Wireless Connectivity
a. Unpack the box and verify the contents.
Using a computer with an 802.11a/g wireless adapter, verify connectivity by using a
browser such as Netscape® or Internet Explorer to connect to the Internet, or check for
file and printer access on your network.
•
•
When prompted, enter admin for the user name and
password for the password, both in lower case letters.
b. Prepare a PC with an Ethernet
adapter. If this PC is already part
Click the Basic Settings link and configure the IP Settings for your network.
of your network, record its
Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference
Manual on the Resource CD for ProSafe Wireless Access Point.
Blue NETGEAR
TCP/IP configuration settings.
Configure the PC with a static IP
address of 192.168.0.36 and
A
b. Configure the wireless interface for wireless access. See the online help or the
Reference Manual for full instructions.
Cable
c. Test wireless connectivity using a PC with a wireless adapter configured
according to the wireless settings you just set in the WAG302 to establish a
wireless connection to the WAG302.
255.255.255.0 as the subnet mask.
c. Connect an Ethernet cable from
the WAG302 to the PC (point A in
the illustration).
B
Now that you have finished the setup steps, you are ready to deploy the WAG302 in
your network. If needed, you can now reconfigure the PC you used in step 1 back to
its original TCP/IP settings.
Computer
d. Securely insert the other end of the
Ethernet
Port
WAG302
cable into the WAG302 Ethernet
port (point B in the illustration).
Download from Www.Somanuals.com. All Manuals Search And Download.
|